From: Sriram R <srirrama@codeaurora.org>
To: Greg KH <gregkh@linuxfoundation.org>
Cc: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>,
linux-wireless@vger.kernel.org, ath10k@lists.infradead.org,
stable@vger.kernel.org
Subject: Re: [PATCH 2/2 - linux-stable-4.4] ath10k: rebuild crypto header in rx data frames
Date: Tue, 01 May 2018 05:44:19 +0530 [thread overview]
Message-ID: <dc88bf84bb843958dceb401ca2e6be17@codeaurora.org> (raw)
In-Reply-To: <583dcb6821d9803277f60780385dff52@codeaurora.org>
On 2018-05-01 05:14, Sriram R wrote:
> On 2018-05-01 00:39, Greg KH wrote:
>> On Mon, Apr 30, 2018 at 11:56:27AM +0530, Sriram R wrote:
>>> Rx data frames notified through HTT_T2H_MSG_TYPE_RX_IND and
>>> HTT_T2H_MSG_TYPE_RX_FRAG_IND expect PN/TSC check to be done
>>> on host (mac80211) rather than firmware. Rebuild cipher header
>>> in every received data frames (that are notified through those
>>> HTT interfaces) from the rx_hdr_status tlv available in the
>>> rx descriptor of the first msdu. Skip setting RX_FLAG_IV_STRIPPED
>>> flag for the packets which requires mac80211 PN/TSC check support
>>> and set appropriate RX_FLAG for stripped crypto tail. Hw QCA988X,
>>> and QCA99X0 currently need the rebuilding of cipher header to
>>> perform PN/TSC check for replay attack.
>>>
>>> [Upstream Commit : 7eccb738fce57cbe53ed903ccf43f9ab257b15b3]
>>>
>>> Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
>>> Signed-off-by: Sriram R <srirrama@codeaurora.org>
>>> ---
>>> drivers/net/wireless/ath/ath10k/htt_rx.c | 98
>>> ++++++++++++++++++++++++++------
>>> 1 file changed, 82 insertions(+), 16 deletions(-)
>>
>> This patch breaks the build. Always test build your patches!
>>
>> thanks,
>>
>> greg k-h
> Hi Greg,
>
> This patch along with its dependency patches (in the following order)
>
> f980ebc058c2 : mac80211: allow not sending MIC up from driver for HW
> crypto
> f631a77ba920 : mac80211: allow same PN for AMSDU sub-frames
> cef0acd4d7d4 : mac80211: Add RX flag to indicate ICV stripped
> [PATCH 1/2 linux-stable-4.4] ath10k: Add new hw param to identify
> alignment for different chipsets
>
Hi Greg,
I feel this breaks since the above mentioned mac80211 commits are not
available in this queue.
https://git.kernel.org/pub/scm/linux/kernel/git/stable/stable-queue.git/diff/queue-4.4/series?id=8e2985dd801f00640be6998ec831018a688bb221
Could you please check after these commits are queued as well before
this patch is applied.
Please let me know if i miss something here so i could check from my
side as well.
Thanks,
Sriram.R
> build fine when checked with v4.4.130.
>
> Kindly let me know if you face any issues while trying out in this
> order.
>
> Thanks,
> Sriram.R
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
WARNING: multiple messages have this Message-ID (diff)
From: Sriram R <srirrama@codeaurora.org>
To: Greg KH <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org, linux-wireless@vger.kernel.org,
ath10k@lists.infradead.org,
Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Subject: Re: [PATCH 2/2 - linux-stable-4.4] ath10k: rebuild crypto header in rx data frames
Date: Tue, 01 May 2018 05:44:19 +0530 [thread overview]
Message-ID: <dc88bf84bb843958dceb401ca2e6be17@codeaurora.org> (raw)
In-Reply-To: <583dcb6821d9803277f60780385dff52@codeaurora.org>
On 2018-05-01 05:14, Sriram R wrote:
> On 2018-05-01 00:39, Greg KH wrote:
>> On Mon, Apr 30, 2018 at 11:56:27AM +0530, Sriram R wrote:
>>> Rx data frames notified through HTT_T2H_MSG_TYPE_RX_IND and
>>> HTT_T2H_MSG_TYPE_RX_FRAG_IND expect PN/TSC check to be done
>>> on host (mac80211) rather than firmware. Rebuild cipher header
>>> in every received data frames (that are notified through those
>>> HTT interfaces) from the rx_hdr_status tlv available in the
>>> rx descriptor of the first msdu. Skip setting RX_FLAG_IV_STRIPPED
>>> flag for the packets which requires mac80211 PN/TSC check support
>>> and set appropriate RX_FLAG for stripped crypto tail. Hw QCA988X,
>>> and QCA99X0 currently need the rebuilding of cipher header to
>>> perform PN/TSC check for replay attack.
>>>
>>> [Upstream Commit : 7eccb738fce57cbe53ed903ccf43f9ab257b15b3]
>>>
>>> Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
>>> Signed-off-by: Sriram R <srirrama@codeaurora.org>
>>> ---
>>> drivers/net/wireless/ath/ath10k/htt_rx.c | 98
>>> ++++++++++++++++++++++++++------
>>> 1 file changed, 82 insertions(+), 16 deletions(-)
>>
>> This patch breaks the build. Always test build your patches!
>>
>> thanks,
>>
>> greg k-h
> Hi Greg,
>
> This patch along with its dependency patches (in the following order)
>
> f980ebc058c2 : mac80211: allow not sending MIC up from driver for HW
> crypto
> f631a77ba920 : mac80211: allow same PN for AMSDU sub-frames
> cef0acd4d7d4 : mac80211: Add RX flag to indicate ICV stripped
> [PATCH 1/2 linux-stable-4.4] ath10k: Add new hw param to identify
> alignment for different chipsets
>
Hi Greg,
I feel this breaks since the above mentioned mac80211 commits are not
available in this queue.
https://git.kernel.org/pub/scm/linux/kernel/git/stable/stable-queue.git/diff/queue-4.4/series?id=8e2985dd801f00640be6998ec831018a688bb221
Could you please check after these commits are queued as well before
this patch is applied.
Please let me know if i miss something here so i could check from my
side as well.
Thanks,
Sriram.R
> build fine when checked with v4.4.130.
>
> Kindly let me know if you face any issues while trying out in this
> order.
>
> Thanks,
> Sriram.R
next prev parent reply other threads:[~2018-05-01 0:14 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-04-30 6:26 [PATCH 0/2 linux-stable-4.4] ath10k: rebuild crypto header in rx data frames Sriram R
2018-04-30 6:26 ` Sriram R
2018-04-30 6:26 ` [PATCH 1/2 linux-stable-4.4] ath10k: Add new hw param to identify alignment for different chipsets Sriram R
2018-04-30 6:26 ` Sriram R
2018-04-30 6:26 ` [PATCH 2/2 - linux-stable-4.4] ath10k: rebuild crypto header in rx data frames Sriram R
2018-04-30 6:26 ` Sriram R
2018-04-30 19:09 ` Greg KH
2018-04-30 19:09 ` Greg KH
2018-04-30 23:44 ` Sriram R
2018-04-30 23:44 ` Sriram R
2018-05-01 0:14 ` Sriram R [this message]
2018-05-01 0:14 ` Sriram R
2018-05-01 15:00 ` Greg KH
2018-05-01 15:00 ` Greg KH
2018-05-01 15:18 ` Sriram R
2018-05-01 15:18 ` Sriram R
2018-04-30 18:16 ` [PATCH 0/2 " Greg KH
2018-04-30 18:16 ` Greg KH
2018-05-02 20:59 ` Greg KH
2018-05-02 20:59 ` Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=dc88bf84bb843958dceb401ca2e6be17@codeaurora.org \
--to=srirrama@codeaurora.org \
--cc=ath10k@lists.infradead.org \
--cc=gregkh@linuxfoundation.org \
--cc=linux-wireless@vger.kernel.org \
--cc=stable@vger.kernel.org \
--cc=vthiagar@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.