* [PATCH v4 0/6] Add TPS6594 PMIC support on several boards
@ 2023-07-27 13:09 ` Esteban Blanc
0 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
TPS6594 is a Power Management IC which provides regulators and others
features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and
PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can
communicate through the I2C or SPI interfaces.
TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives.
This serie adds device tree nodes for TI TPS6594 PMICs found in the
following boards:
- J721EXSOMXEVM:
Link: https://www.ti.com/tool/J721EXSOMXEVM
- J721S2XSOMXEVM:
Link: https://www.ti.com/tool/J721S2XSOMXEVM
- J7200XSOMXEVM:
Link: https://www.ti.com/tool/J7200XSOMXEVM
- AM62A-SKEVM:
Link: https://www.ti.com/tool/SK-AM62A-LP
- J784S4XEVM
Link: https://www.ti.com/tool/J784S4XEVM
Changes from v3:
https://lore.kernel.org/all/20230417154832.216774-1-eblanc@baylibre.com/
- Rebased on top of v6.5-rc1.
- Change pinctrl number for irq pin as wkup_pmx0 was split on some boards.
- Use already present wkup_i2c0 node instead of creating a new one.
Changes from v2:
https://lore.kernel.org/lkml/20230414112843.1358067-1-eblanc@baylibre.com/
- Change node name as per Krzysztof review.
- Add a fix for the interrupt range of wakeup gpio used by TPS6594 pmic
on J784S4.
The interruptions of the PMIC were not working before that.
- Remove dependencies on other patch series as that was a mistake, see
https://lore.kernel.org/lkml/CRYY2V3HJ0CP.96JQ18PLZB3C@burritosblues/
Changes from v1:
https://lore.kernel.org/lkml/20230329142948.833800-1-eblanc@baylibre.com/
- Harmonize regulators names across the different boards.
- Adjust AVS voltage range.
- Remove some outdated comments.
- Add PMIC to J784S4 board.
- Compatible string modified to match dt-bindings.
- Add gpio-controller and gpio-cells properties.
Apelete Seketeli (1):
arm64: dts: ti: k3-j784s4-evm: Fix interrupt ranges for TPS6594 PMIC
Esteban Blanc (2):
arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
Jerome Neanne (2):
arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC
Julien Panis (1):
arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC
arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 95 +++++++++
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 ++++++++++++++
arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 163 ++++++++++++++
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 ++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 104 +++++++++
.../boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 2 +-
6 files changed, 719 insertions(+), 1 deletion(-)
--
2.38.5
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v4 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
2023-07-27 13:09 ` Esteban Blanc
@ 2023-07-27 13:09 ` Esteban Blanc
-1 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 ++++++++++++++++++++
1 file changed, 157 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index b37f4f88ece4..e45d97cc41a5 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -127,6 +127,14 @@ J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
};
};
+&wkup_pmx3 {
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
+ >;
+ };
+};
+
&main_pmx0 {
main_i2c0_pins_default: main-i2c0-default-pins {
pinctrl-single,pins = <
@@ -264,6 +272,155 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659414: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka1: buck1 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka2: buck2 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_phyio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd1_lpddr4_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdd_wk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ lp876441: pmic@4c {
+ compatible = "ti,lp8764-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+
+ regulators: regulators {
+ buckb1: buck1 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buckb2: buck2 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb3: buck3 {
+ regulator-name = "vdd_core_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb4: buck4 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&ospi0 {
--
2.38.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v4 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
@ 2023-07-27 13:09 ` Esteban Blanc
0 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 ++++++++++++++++++++
1 file changed, 157 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index b37f4f88ece4..e45d97cc41a5 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -127,6 +127,14 @@ J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /* (H21) WKUP_I2C0_SDA */
};
};
+&wkup_pmx3 {
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 7) /* (E18) WKUP_GPIO0_84 */
+ >;
+ };
+};
+
&main_pmx0 {
main_i2c0_pins_default: main-i2c0-default-pins {
pinctrl-single,pins = <
@@ -264,6 +272,155 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659414: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka1: buck1 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka2: buck2 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_phyio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd1_lpddr4_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdd_wk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ lp876441: pmic@4c {
+ compatible = "ti,lp8764-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <84 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+
+ regulators: regulators {
+ buckb1: buck1 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buckb2: buck2 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb3: buck3 {
+ regulator-name = "vdd_core_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb4: buck4 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&ospi0 {
--
2.38.5
^ permalink raw reply related [flat|nested] 24+ messages in thread* RE: [PATCH v4 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
2023-07-27 13:09 ` Esteban Blanc
@ 2023-08-02 4:04 ` Kumar, Udit
-1 siblings, 0 replies; 24+ messages in thread
From: Kumar, Udit @ 2023-08-02 4:04 UTC (permalink / raw)
To: Esteban Blanc, Menon, Nishanth, Raghavendra, Vignesh,
kristo@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, jneanne@baylibre.com,
aseketeli@baylibre.com, jpanis@baylibre.com, Tonking, Reid
Hi Esteban,
>This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
>Theses devices provides regulators (bucks and LDOs), but also
>GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
>which monitors the SoC error output signal, and a PFSM
>(Pre-configurable Finite State Machine) which manages the
>operational modes of the PMIC.
>
>Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
>---
> arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 ++++++++++++++++++++
> 1 file changed, 157 insertions(+)
>
>diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
>b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
>index b37f4f88ece4..e45d97cc41a5 100644
>--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
>+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
>@@ -127,6 +127,14 @@ J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /*
>(H21) WKUP_I2C0_SDA */
> };
> };
>
>+&wkup_pmx3 {
>+ pmic_irq_pins_default: pmic-irq-pins-default {
>+ pinctrl-single,pins = <
>+ J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 7) /* (E18)
>WKUP_GPIO0_84 */
Could you use 0x01c format instead of 0x1c,
and similar format in other patches in this series too.
Rest LGTM
>+ >;
>+ };
>+};
>+
[..]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread* RE: [PATCH v4 1/6] arm64: dts: ti: k3-j7200-som-p0: Add TP6594 family PMICs
@ 2023-08-02 4:04 ` Kumar, Udit
0 siblings, 0 replies; 24+ messages in thread
From: Kumar, Udit @ 2023-08-02 4:04 UTC (permalink / raw)
To: Esteban Blanc, Menon, Nishanth, Raghavendra, Vignesh,
kristo@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, jneanne@baylibre.com,
aseketeli@baylibre.com, jpanis@baylibre.com, Tonking, Reid
Hi Esteban,
>This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
>Theses devices provides regulators (bucks and LDOs), but also
>GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
>which monitors the SoC error output signal, and a PFSM
>(Pre-configurable Finite State Machine) which manages the
>operational modes of the PMIC.
>
>Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
>---
> arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 157 ++++++++++++++++++++
> 1 file changed, 157 insertions(+)
>
>diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
>b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
>index b37f4f88ece4..e45d97cc41a5 100644
>--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
>+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
>@@ -127,6 +127,14 @@ J721E_WKUP_IOPAD(0x9c, PIN_INPUT_PULLUP, 0) /*
>(H21) WKUP_I2C0_SDA */
> };
> };
>
>+&wkup_pmx3 {
>+ pmic_irq_pins_default: pmic-irq-pins-default {
>+ pinctrl-single,pins = <
>+ J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 7) /* (E18)
>WKUP_GPIO0_84 */
Could you use 0x01c format instead of 0x1c,
and similar format in other patches in this series too.
Rest LGTM
>+ >;
>+ };
>+};
>+
[..]
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v4 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
2023-07-27 13:09 ` Esteban Blanc
@ 2023-07-27 13:09 ` Esteban Blanc
-1 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
1 file changed, 199 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index d57dd43da0ef..5348aafe3277 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -61,6 +61,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
};
};
+&wkup_pmx1 {
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J721S2_WKUP_IOPAD(0x28, PIN_INPUT, 7)
+ >;
+ };
+};
+
&wkup_pmx2 {
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
pinctrl-single,pins = <
@@ -97,6 +106,196 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659411: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka1234: buck1234 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd_mcuwk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcu_gpioret_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659414: pmic@4c {
+ compatible = "ti,tps6594-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ buckb1: buck1 {
+ regulator-name = "vdd_io_1v8_reg";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buckb2: buck2 {
+ regulator-name = "vdd_fpd_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb3: buck3 {
+ regulator-name = "vdd_phy_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb5: buck5 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob1: ldo1 {
+ regulator-name = "vdd_wk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob2: ldo2 {
+ regulator-name = "vdd_gpioret_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob3: ldo3 {
+ regulator-name = "vda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ lp876411: pmic@58 {
+ compatible = "ti,lp8764-q1";
+ reg = <0x58>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+
+ regulators {
+ buckc1234: buck1234 {
+ regulator-name = "vdd_core_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&main_i2c0 {
--
2.38.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v4 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
@ 2023-07-27 13:09 ` Esteban Blanc
0 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
1 file changed, 199 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
index d57dd43da0ef..5348aafe3277 100644
--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -61,6 +61,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */
};
};
+&wkup_pmx1 {
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J721S2_WKUP_IOPAD(0x28, PIN_INPUT, 7)
+ >;
+ };
+};
+
&wkup_pmx2 {
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
pinctrl-single,pins = <
@@ -97,6 +106,196 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659411: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka1234: buck1234 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd_mcuwk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcu_gpioret_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659414: pmic@4c {
+ compatible = "ti,tps6594-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1-supply = <&vsys_3v3>;
+ buck2-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ buckb1: buck1 {
+ regulator-name = "vdd_io_1v8_reg";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buckb2: buck2 {
+ regulator-name = "vdd_fpd_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb3: buck3 {
+ regulator-name = "vdd_phy_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb5: buck5 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob1: ldo1 {
+ regulator-name = "vdd_wk_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob2: ldo2 {
+ regulator-name = "vdd_gpioret_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob3: ldo3 {
+ regulator-name = "vda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ lp876411: pmic@58 {
+ compatible = "ti,lp8764-q1";
+ reg = <0x58>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+
+ regulators {
+ buckc1234: buck1234 {
+ regulator-name = "vdd_core_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&main_i2c0 {
--
2.38.5
^ permalink raw reply related [flat|nested] 24+ messages in thread* RE: [PATCH v4 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
2023-07-27 13:09 ` Esteban Blanc
@ 2023-08-03 10:31 ` Kumar, Udit
-1 siblings, 0 replies; 24+ messages in thread
From: Kumar, Udit @ 2023-08-03 10:31 UTC (permalink / raw)
To: Esteban Blanc, Menon, Nishanth, Raghavendra, Vignesh,
kristo@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, jneanne@baylibre.com,
aseketeli@baylibre.com, jpanis@baylibre.com, Achath, Vaishnav
Hi Esteban
> [...]
>Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
>---
> arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
> 1 file changed, 199 insertions(+)
>
>diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>index d57dd43da0ef..5348aafe3277 100644
>--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>@@ -61,6 +61,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20)
>MCU_OSPI0_LBCLKO */
> };
> };
>
>+&wkup_pmx1 {
>+ pmic_irq_pins_default: pmic-irq-pins-default {
>+ pinctrl-single,pins = <
>+ /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
>+ J721S2_WKUP_IOPAD(0x28, PIN_INPUT, 7)
>+ >;
I see, this pin is getting shared with OSPI-1 .
I think either OSPI or PMIC could be functional at one time ?
>+ };
>+};
>+
> [...]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread* RE: [PATCH v4 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
@ 2023-08-03 10:31 ` Kumar, Udit
0 siblings, 0 replies; 24+ messages in thread
From: Kumar, Udit @ 2023-08-03 10:31 UTC (permalink / raw)
To: Esteban Blanc, Menon, Nishanth, Raghavendra, Vignesh,
kristo@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, jneanne@baylibre.com,
aseketeli@baylibre.com, jpanis@baylibre.com, Achath, Vaishnav
Hi Esteban
> [...]
>Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
>---
> arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
> 1 file changed, 199 insertions(+)
>
>diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>index d57dd43da0ef..5348aafe3277 100644
>--- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>@@ -61,6 +61,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20)
>MCU_OSPI0_LBCLKO */
> };
> };
>
>+&wkup_pmx1 {
>+ pmic_irq_pins_default: pmic-irq-pins-default {
>+ pinctrl-single,pins = <
>+ /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
>+ J721S2_WKUP_IOPAD(0x28, PIN_INPUT, 7)
>+ >;
I see, this pin is getting shared with OSPI-1 .
I think either OSPI or PMIC could be functional at one time ?
>+ };
>+};
>+
> [...]
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v4 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
2023-08-03 10:31 ` Kumar, Udit
@ 2023-08-03 11:13 ` Vaishnav Achath
-1 siblings, 0 replies; 24+ messages in thread
From: Vaishnav Achath @ 2023-08-03 11:13 UTC (permalink / raw)
To: Kumar, Udit, Esteban Blanc, Menon, Nishanth, Raghavendra, Vignesh,
kristo@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, jneanne@baylibre.com,
aseketeli@baylibre.com, jpanis@baylibre.com
On 03/08/23 16:01, Kumar, Udit wrote:
> Hi Esteban
>
Hi Esteban, Udit,
>> [...]
>> Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
>> ---
>> arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
>> 1 file changed, 199 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>> b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>> index d57dd43da0ef..5348aafe3277 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>> @@ -61,6 +61,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20)
>> MCU_OSPI0_LBCLKO */
>> };
>> };
>>
>> +&wkup_pmx1 {
>> + pmic_irq_pins_default: pmic-irq-pins-default {
>> + pinctrl-single,pins = <
>> + /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
>> + J721S2_WKUP_IOPAD(0x28, PIN_INPUT, 7)
>> + >;
>
> I see, this pin is getting shared with OSPI-1 .
> I think either OSPI or PMIC could be functional at one time ?
>
OSPI CS1 is not being used, so the corresponding entry under OSPI1 can be removed.
Thanks and Regards,
Vaishnav
>> + };
>> +};
>> +
>> [...]
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v4 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
@ 2023-08-03 11:13 ` Vaishnav Achath
0 siblings, 0 replies; 24+ messages in thread
From: Vaishnav Achath @ 2023-08-03 11:13 UTC (permalink / raw)
To: Kumar, Udit, Esteban Blanc, Menon, Nishanth, Raghavendra, Vignesh,
kristo@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, jneanne@baylibre.com,
aseketeli@baylibre.com, jpanis@baylibre.com
On 03/08/23 16:01, Kumar, Udit wrote:
> Hi Esteban
>
Hi Esteban, Udit,
>> [...]
>> Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
>> ---
>> arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
>> 1 file changed, 199 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>> b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>> index d57dd43da0ef..5348aafe3277 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>> @@ -61,6 +61,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20)
>> MCU_OSPI0_LBCLKO */
>> };
>> };
>>
>> +&wkup_pmx1 {
>> + pmic_irq_pins_default: pmic-irq-pins-default {
>> + pinctrl-single,pins = <
>> + /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
>> + J721S2_WKUP_IOPAD(0x28, PIN_INPUT, 7)
>> + >;
>
> I see, this pin is getting shared with OSPI-1 .
> I think either OSPI or PMIC could be functional at one time ?
>
OSPI CS1 is not being used, so the corresponding entry under OSPI1 can be removed.
Thanks and Regards,
Vaishnav
>> + };
>> +};
>> +
>> [...]
>
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v4 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
2023-08-03 11:13 ` Vaishnav Achath
@ 2023-08-03 12:43 ` Kumar, Udit
-1 siblings, 0 replies; 24+ messages in thread
From: Kumar, Udit @ 2023-08-03 12:43 UTC (permalink / raw)
To: Vaishnav Achath, Esteban Blanc, Menon, Nishanth,
Raghavendra, Vignesh, kristo@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, jneanne@baylibre.com,
aseketeli@baylibre.com, jpanis@baylibre.com, u-kumar1
Thanks Vaishnav
On 8/3/2023 4:43 PM, Vaishnav Achath wrote:
>
> On 03/08/23 16:01, Kumar, Udit wrote:
>> Hi Esteban
>>
> Hi Esteban, Udit,
>
>>> [...]
>>> Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
>>> ---
>>> arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
>>> 1 file changed, 199 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>>> b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>>> index d57dd43da0ef..5348aafe3277 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>>> @@ -61,6 +61,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20)
>>> MCU_OSPI0_LBCLKO */
>>> };
>>> };
>>>
>>> +&wkup_pmx1 {
>>> + pmic_irq_pins_default: pmic-irq-pins-default {
>>> + pinctrl-single,pins = <
>>> + /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
>>> + J721S2_WKUP_IOPAD(0x28, PIN_INPUT, 7)
>>> + >;
>> I see, this pin is getting shared with OSPI-1 .
>> I think either OSPI or PMIC could be functional at one time ?
>>
> OSPI CS1 is not being used, so the corresponding entry under OSPI1 can be removed.
let me handle this in on going series
https://lore.kernel.org/all/20230802113500.162276-1-u-kumar1@ti.com/
> Thanks and Regards,
> Vaishnav
>
>>> + };
>>> +};
>>> +
>>> [...]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v4 2/6] arm64: dts: ti: k3-j721s2-som-p0: Add TP6594 family PMICs
@ 2023-08-03 12:43 ` Kumar, Udit
0 siblings, 0 replies; 24+ messages in thread
From: Kumar, Udit @ 2023-08-03 12:43 UTC (permalink / raw)
To: Vaishnav Achath, Esteban Blanc, Menon, Nishanth,
Raghavendra, Vignesh, kristo@kernel.org, robh+dt@kernel.org,
krzysztof.kozlowski+dt@linaro.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, jneanne@baylibre.com,
aseketeli@baylibre.com, jpanis@baylibre.com, u-kumar1
Thanks Vaishnav
On 8/3/2023 4:43 PM, Vaishnav Achath wrote:
>
> On 03/08/23 16:01, Kumar, Udit wrote:
>> Hi Esteban
>>
> Hi Esteban, Udit,
>
>>> [...]
>>> Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
>>> ---
>>> arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 199 +++++++++++++++++++
>>> 1 file changed, 199 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>>> b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>>> index d57dd43da0ef..5348aafe3277 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
>>> @@ -61,6 +61,15 @@ J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20)
>>> MCU_OSPI0_LBCLKO */
>>> };
>>> };
>>>
>>> +&wkup_pmx1 {
>>> + pmic_irq_pins_default: pmic-irq-pins-default {
>>> + pinctrl-single,pins = <
>>> + /* (C21) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
>>> + J721S2_WKUP_IOPAD(0x28, PIN_INPUT, 7)
>>> + >;
>> I see, this pin is getting shared with OSPI-1 .
>> I think either OSPI or PMIC could be functional at one time ?
>>
> OSPI CS1 is not being used, so the corresponding entry under OSPI1 can be removed.
let me handle this in on going series
https://lore.kernel.org/all/20230802113500.162276-1-u-kumar1@ti.com/
> Thanks and Regards,
> Vaishnav
>
>>> + };
>>> +};
>>> +
>>> [...]
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v4 3/6] arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
2023-07-27 13:09 ` Esteban Blanc
@ 2023-07-27 13:09 ` Esteban Blanc
-1 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
From: Jerome Neanne <jneanne@baylibre.com>
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 163 ++++++++++++++++++++
1 file changed, 163 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index 38ae13cc3aa3..c16dc59e1b0e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -152,6 +152,12 @@ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
>;
};
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xd4, PIN_INPUT, 7) /* (G26) WKUP_GPIO0_9 */
+ >;
+ };
+
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
@@ -212,6 +218,163 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659413: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ ti,primary-pmic;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck12-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka12: buck12 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_phyio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd1_lpddr4_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659411: pmic@4c {
+ compatible = "ti,tps6594-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ buckb1234: buck1234 {
+ regulator-name = "vdd_core_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb5: buck5 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob1: ldo1 {
+ regulator-name = "vdd_sd_dv";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob2: ldo2 {
+ regulator-name = "vdd_usb_3v3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob3: ldo3 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&ospi0 {
--
2.38.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v4 3/6] arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
@ 2023-07-27 13:09 ` Esteban Blanc
0 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
From: Jerome Neanne <jneanne@baylibre.com>
This patch adds support for TPS6594 PMIC family on wakup I2C0 bus.
Theses devices provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 163 ++++++++++++++++++++
1 file changed, 163 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index 38ae13cc3aa3..c16dc59e1b0e 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -152,6 +152,12 @@ J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
>;
};
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xd4, PIN_INPUT, 7) /* (G26) WKUP_GPIO0_9 */
+ >;
+ };
+
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
pinctrl-single,pins = <
J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
@@ -212,6 +218,163 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659413: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ ti,primary-pmic;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck12-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka12: buck12 {
+ regulator-name = "vdd_cpu_avs";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_phyio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd1_lpddr4_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vdda_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+
+ tps659411: pmic@4c {
+ compatible = "ti,tps6594-q1";
+ reg = <0x4c>;
+ system-power-controller;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck1234-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ buckb1234: buck1234 {
+ regulator-name = "vdd_core_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buckb5: buck5 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob1: ldo1 {
+ regulator-name = "vdd_sd_dv";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob2: ldo2 {
+ regulator-name = "vdd_usb_3v3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob3: ldo3 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldob4: ldo4 {
+ regulator-name = "vda_pll_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&ospi0 {
--
2.38.5
^ permalink raw reply related [flat|nested] 24+ messages in thread* Re: [PATCH v4 3/6] arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
2023-07-27 13:09 ` Esteban Blanc
@ 2023-08-03 15:52 ` jerome Neanne
-1 siblings, 0 replies; 24+ messages in thread
From: jerome Neanne @ 2023-08-03 15:52 UTC (permalink / raw)
To: Esteban Blanc, nm, vigneshr, kristo, robh+dt,
krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, aseketeli,
jpanis
On 27/07/2023 15:09, Esteban Blanc wrote:
> From: Jerome Neanne <jneanne@baylibre.com>
>
[...]
> + tps659411: pmic@4c {
> + compatible = "ti,tps6594-q1";
> + reg = <0x4c>;
> + system-power-controller;
> + interrupt-parent = <&wkup_gpio0>;
> + interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + buck1234-supply = <&vsys_3v3>;
> + buck5-supply = <&vsys_3v3>;
> + ldo1-supply = <&vsys_3v3>;
> + ldo2-supply = <&vsys_3v3>;
> + ldo3-supply = <&vsys_3v3>;
> + ldo4-supply = <&vsys_3v3>;
> +
> + regulators {
> + buckb1234: buck1234 {
> + regulator-name = "vdd_core_0v8";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buckb5: buck5 {
> + regulator-name = "vdd_ram_0v85";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldob1: ldo1 {
> + regulator-name = "vdd_sd_dv";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldob2: ldo2 {
> + regulator-name = "vdd_usb_3v3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
This voltage is static 3.3V: regulator-min-microvolt = <3300000>;
> + ldob3: ldo3 {
> + regulator-name = "vdd_io_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldob4: ldo4 {
> + regulator-name = "vda_pll_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> };
>
> &ospi0 {
Regards,
Jerome.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 24+ messages in thread* Re: [PATCH v4 3/6] arm64: dts: ti: k3-j721e-som-p0: Add TP6594 family PMICs
@ 2023-08-03 15:52 ` jerome Neanne
0 siblings, 0 replies; 24+ messages in thread
From: jerome Neanne @ 2023-08-03 15:52 UTC (permalink / raw)
To: Esteban Blanc, nm, vigneshr, kristo, robh+dt,
krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, aseketeli,
jpanis
On 27/07/2023 15:09, Esteban Blanc wrote:
> From: Jerome Neanne <jneanne@baylibre.com>
>
[...]
> + tps659411: pmic@4c {
> + compatible = "ti,tps6594-q1";
> + reg = <0x4c>;
> + system-power-controller;
> + interrupt-parent = <&wkup_gpio0>;
> + interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> +
> + buck1234-supply = <&vsys_3v3>;
> + buck5-supply = <&vsys_3v3>;
> + ldo1-supply = <&vsys_3v3>;
> + ldo2-supply = <&vsys_3v3>;
> + ldo3-supply = <&vsys_3v3>;
> + ldo4-supply = <&vsys_3v3>;
> +
> + regulators {
> + buckb1234: buck1234 {
> + regulator-name = "vdd_core_0v8";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + buckb5: buck5 {
> + regulator-name = "vdd_ram_0v85";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldob1: ldo1 {
> + regulator-name = "vdd_sd_dv";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldob2: ldo2 {
> + regulator-name = "vdd_usb_3v3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
This voltage is static 3.3V: regulator-min-microvolt = <3300000>;
> + ldob3: ldo3 {
> + regulator-name = "vdd_io_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldob4: ldo4 {
> + regulator-name = "vda_pll_1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> };
>
> &ospi0 {
Regards,
Jerome.
^ permalink raw reply [flat|nested] 24+ messages in thread
* [PATCH v4 4/6] arm64: dts: ti: k3-j784s4-evm: Fix interrupt ranges for TPS6594 PMIC
2023-07-27 13:09 ` Esteban Blanc
@ 2023-07-27 13:09 ` Esteban Blanc
-1 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
From: Apelete Seketeli <aseketeli@baylibre.com>
This patch fixes the interrupt range for TPS6594 PMIC on MCU/WAKEUP
domain for RTC peripheral.
Signed-off-by: Apelete Seketeli <aseketeli@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
index 657fb1d72512..62a0f172fb2d 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
@@ -107,7 +107,7 @@ wkup_gpio_intr: interrupt-controller@42200000 {
#interrupt-cells = <1>;
ti,sci = <&sms>;
ti,sci-dev-id = <177>;
- ti,interrupt-ranges = <16 928 16>;
+ ti,interrupt-ranges = <16 960 16>;
};
/* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */
--
2.38.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v4 4/6] arm64: dts: ti: k3-j784s4-evm: Fix interrupt ranges for TPS6594 PMIC
@ 2023-07-27 13:09 ` Esteban Blanc
0 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
From: Apelete Seketeli <aseketeli@baylibre.com>
This patch fixes the interrupt range for TPS6594 PMIC on MCU/WAKEUP
domain for RTC peripheral.
Signed-off-by: Apelete Seketeli <aseketeli@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
index 657fb1d72512..62a0f172fb2d 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-mcu-wakeup.dtsi
@@ -107,7 +107,7 @@ wkup_gpio_intr: interrupt-controller@42200000 {
#interrupt-cells = <1>;
ti,sci = <&sms>;
ti,sci-dev-id = <177>;
- ti,interrupt-ranges = <16 928 16>;
+ ti,interrupt-ranges = <16 960 16>;
};
/* MCU_TIMERIO pad input CTRLMMR_MCU_TIMER*_CTRL registers */
--
2.38.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v4 5/6] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC
2023-07-27 13:09 ` Esteban Blanc
@ 2023-07-27 13:09 ` Esteban Blanc
-1 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
From: Jerome Neanne <jneanne@baylibre.com>
This patch adds support for TPS6593 PMIC on wkup I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 104 +++++++++++++++++++++++
1 file changed, 104 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 430b8a2c5df5..c37a94ac98cf 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -251,6 +251,10 @@ vdd_sd_dv: regulator-TLV71033 {
};
};
+&wkup_gpio0 {
+ status = "okay";
+};
+
&main_pmx0 {
main_uart8_pins_default: main-uart8-default-pins {
pinctrl-single,pins = <
@@ -365,6 +369,17 @@ J784S4_WKUP_IOPAD(0x170, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
};
};
+&wkup_pmx1 {
+ status = "okay";
+
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ /* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J784S4_WKUP_IOPAD(0x28, PIN_INPUT, 7)
+ >;
+ };
+};
+
&wkup_pmx0 {
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
pinctrl-single,pins = <
@@ -416,6 +431,95 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659413: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+ ti,primary-pmic;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck12-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka12: buck12 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcuio_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vds_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&mcu_uart0 {
--
2.38.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v4 5/6] arm64: dts: ti: k3-j784s4-evm: Add support for TPS6594 PMIC
@ 2023-07-27 13:09 ` Esteban Blanc
0 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
From: Jerome Neanne <jneanne@baylibre.com>
This patch adds support for TPS6593 PMIC on wkup I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 104 +++++++++++++++++++++++
1 file changed, 104 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 430b8a2c5df5..c37a94ac98cf 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -251,6 +251,10 @@ vdd_sd_dv: regulator-TLV71033 {
};
};
+&wkup_gpio0 {
+ status = "okay";
+};
+
&main_pmx0 {
main_uart8_pins_default: main-uart8-default-pins {
pinctrl-single,pins = <
@@ -365,6 +369,17 @@ J784S4_WKUP_IOPAD(0x170, PIN_INPUT, 0) /* (Y36) MCU_ADC1_AIN7 */
};
};
+&wkup_pmx1 {
+ status = "okay";
+
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ /* (G33) MCU_OSPI1_CSn1.WKUP_GPIO0_39 */
+ J784S4_WKUP_IOPAD(0x28, PIN_INPUT, 7)
+ >;
+ };
+};
+
&wkup_pmx0 {
mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-default-pins {
pinctrl-single,pins = <
@@ -416,6 +431,95 @@ eeprom@50 {
compatible = "atmel,24c256";
reg = <0x50>;
};
+
+ tps659413: pmic@48 {
+ compatible = "ti,tps6594-q1";
+ reg = <0x48>;
+ system-power-controller;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&wkup_gpio0>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+ ti,primary-pmic;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ buck12-supply = <&vsys_3v3>;
+ buck3-supply = <&vsys_3v3>;
+ buck4-supply = <&vsys_3v3>;
+ buck5-supply = <&vsys_3v3>;
+ ldo1-supply = <&vsys_3v3>;
+ ldo2-supply = <&vsys_3v3>;
+ ldo3-supply = <&vsys_3v3>;
+ ldo4-supply = <&vsys_3v3>;
+
+ regulators {
+ bucka12: buck12 {
+ regulator-name = "vdd_ddr_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka3: buck3 {
+ regulator-name = "vdd_ram_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka4: buck4 {
+ regulator-name = "vdd_io_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ bucka5: buck5 {
+ regulator-name = "vdd_mcu_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa1: ldo1 {
+ regulator-name = "vdd_mcuio_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa2: ldo2 {
+ regulator-name = "vdd_mcuio_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa3: ldo3 {
+ regulator-name = "vds_dll_0v8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldoa4: ldo4 {
+ regulator-name = "vda_mcu_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&mcu_uart0 {
--
2.38.5
^ permalink raw reply related [flat|nested] 24+ messages in thread
* [PATCH v4 6/6] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC
2023-07-27 13:09 ` Esteban Blanc
@ 2023-07-27 13:09 ` Esteban Blanc
-1 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
From: Julien Panis <jpanis@baylibre.com>
This patch adds support for TPS6593 PMIC on main I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 95 +++++++++++++++++++++++++
1 file changed, 95 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index ecc0e13331c4..fbf9c5e2c031 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -221,11 +221,106 @@ AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
};
};
+&mcu_pmx0 {
+ status = "okay";
+
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ AM62AX_MCU_IOPAD(0x000, PIN_INPUT, 7) /* (E11) MCU_GPIO0_0 */
+ >;
+ };
+};
+
+&mcu_gpio0 {
+ status = "okay";
+};
+
&main_i2c0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&main_i2c0_pins_default>;
clock-frequency = <400000>;
+
+ tps659312: pmic@48 {
+ compatible = "ti,tps6593-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&mcu_gpio0>;
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+ buck123-supply = <&vcc_3v3_sys>;
+ buck4-supply = <&vcc_3v3_sys>;
+ buck5-supply = <&vcc_3v3_sys>;
+ ldo1-supply = <&vcc_3v3_sys>;
+ ldo2-supply = <&vcc_3v3_sys>;
+ ldo3-supply = <&buck5>;
+ ldo4-supply = <&vcc_3v3_sys>;
+
+ regulators {
+ buck123: buck123 {
+ regulator-name = "vcc_core";
+ regulator-min-microvolt = <715000>;
+ regulator-max-microvolt = <895000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4: buck4 {
+ regulator-name = "vcc_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5: buck5 {
+ regulator-name = "vcc_1v8_sys";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1: ldo1 {
+ regulator-name = "vddshv5_sdio";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2: ldo2 {
+ regulator-name = "vpp_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3: ldo3 {
+ regulator-name = "vcc_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4: ldo4 {
+ regulator-name = "vdda_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&main_i2c1 {
--
2.38.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 24+ messages in thread* [PATCH v4 6/6] arm64: dts: ti: k3-am62a7-sk: Add support for TPS6593 PMIC
@ 2023-07-27 13:09 ` Esteban Blanc
0 siblings, 0 replies; 24+ messages in thread
From: Esteban Blanc @ 2023-07-27 13:09 UTC (permalink / raw)
To: nm, vigneshr, kristo, robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-kernel, devicetree, linux-kernel, u-kumar1, eblanc,
jneanne, aseketeli, jpanis
From: Julien Panis <jpanis@baylibre.com>
This patch adds support for TPS6593 PMIC on main I2C0 bus.
This device provides regulators (bucks and LDOs), but also
GPIOs, a RTC, a watchdog, an ESM (Error Signal Monitor)
which monitors the SoC error output signal, and a PFSM
(Pre-configurable Finite State Machine) which manages the
operational modes of the PMIC.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Signed-off-by: Esteban Blanc <eblanc@baylibre.com>
---
arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 95 +++++++++++++++++++++++++
1 file changed, 95 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
index ecc0e13331c4..fbf9c5e2c031 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -221,11 +221,106 @@ AM62AX_IOPAD(0x12c, PIN_INPUT, 0) /* (W16) RGMII1_TX_CTL */
};
};
+&mcu_pmx0 {
+ status = "okay";
+
+ pmic_irq_pins_default: pmic-irq-pins-default {
+ pinctrl-single,pins = <
+ AM62AX_MCU_IOPAD(0x000, PIN_INPUT, 7) /* (E11) MCU_GPIO0_0 */
+ >;
+ };
+};
+
+&mcu_gpio0 {
+ status = "okay";
+};
+
&main_i2c0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&main_i2c0_pins_default>;
clock-frequency = <400000>;
+
+ tps659312: pmic@48 {
+ compatible = "ti,tps6593-q1";
+ reg = <0x48>;
+ ti,primary-pmic;
+ system-power-controller;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_irq_pins_default>;
+ interrupt-parent = <&mcu_gpio0>;
+ interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+ buck123-supply = <&vcc_3v3_sys>;
+ buck4-supply = <&vcc_3v3_sys>;
+ buck5-supply = <&vcc_3v3_sys>;
+ ldo1-supply = <&vcc_3v3_sys>;
+ ldo2-supply = <&vcc_3v3_sys>;
+ ldo3-supply = <&buck5>;
+ ldo4-supply = <&vcc_3v3_sys>;
+
+ regulators {
+ buck123: buck123 {
+ regulator-name = "vcc_core";
+ regulator-min-microvolt = <715000>;
+ regulator-max-microvolt = <895000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4: buck4 {
+ regulator-name = "vcc_1v1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5: buck5 {
+ regulator-name = "vcc_1v8_sys";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1: ldo1 {
+ regulator-name = "vddshv5_sdio";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2: ldo2 {
+ regulator-name = "vpp_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3: ldo3 {
+ regulator-name = "vcc_0v85";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4: ldo4 {
+ regulator-name = "vdda_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
};
&main_i2c1 {
--
2.38.5
^ permalink raw reply related [flat|nested] 24+ messages in thread