[U-Boot] [PATCH] zynq/board.c: Add support for qspiboot and nandboot

[U-Boot] [PATCH] zynq/board.c: Add support for qspiboot and nandboot

[Mike Looijmans]

The Zynq can also boot from QSPI or NAND, and environment scripting
uses "qspiboot" and "nandboot" already. Add these to the board init
routines so that modeboot is properly set to one of these values when
the mode bits indicate so.

Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
---
 board/xilinx/zynq/board.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
index 5cd9bbf..cf80302 100644
--- a/board/xilinx/zynq/board.c
+++ b/board/xilinx/zynq/board.c
@@ -85,9 +85,15 @@ int board_init(void)
 int board_late_init(void)
 {
 	switch ((zynq_slcr_get_boot_mode()) & ZYNQ_BM_MASK) {
+	case ZYNQ_BM_QSPI:
+		setenv("modeboot", "qspiboot");
+		break;
 	case ZYNQ_BM_NOR:
 		setenv("modeboot", "norboot");
 		break;
+	case ZYNQ_BM_NAND:
+		setenv("modeboot", "nandboot");
+		break;
 	case ZYNQ_BM_SD:
 		setenv("modeboot", "sdboot");
 		break;
-- 
1.9.1

[U-Boot] [PATCH] zynq/board.c: Add support for qspiboot and nandboot

[Michal Simek]

Hi,

On 13.1.2017 14:04, Mike Looijmans wrote:
> The Zynq can also boot from QSPI or NAND, and environment scripting
> uses "qspiboot" and "nandboot" already. Add these to the board init
> routines so that modeboot is properly set to one of these values when
> the mode bits indicate so.
> 
> Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
> ---
>  board/xilinx/zynq/board.c | 6 ++++++
>  1 file changed, 6 insertions(+)
> 
> diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
> index 5cd9bbf..cf80302 100644
> --- a/board/xilinx/zynq/board.c
> +++ b/board/xilinx/zynq/board.c
> @@ -85,9 +85,15 @@ int board_init(void)
>  int board_late_init(void)
>  {
>  	switch ((zynq_slcr_get_boot_mode()) & ZYNQ_BM_MASK) {
> +	case ZYNQ_BM_QSPI:
> +		setenv("modeboot", "qspiboot");
> +		break;
>  	case ZYNQ_BM_NOR:
>  		setenv("modeboot", "norboot");
>  		break;
> +	case ZYNQ_BM_NAND:
> +		setenv("modeboot", "nandboot");
> +		break;
>  	case ZYNQ_BM_SD:
>  		setenv("modeboot", "sdboot");
>  		break;
> 

The same patch was merged some days ago. Please check latest master branch.

Thanks,
Michal

[U-Boot] [PATCH] zynq/board.c: Add support for qspiboot and nandboot

[Mike Looijmans]

?Ah, missed that. I noticed that "run $modeboot" didn't work for QSPI in the 
2017.1 tag, hadn't seen that one yet.

On 13-01-17 14:18, Michal Simek wrote:
> Hi,
>
> On 13.1.2017 14:04, Mike Looijmans wrote:
>> The Zynq can also boot from QSPI or NAND, and environment scripting
>> uses "qspiboot" and "nandboot" already. Add these to the board init
>> routines so that modeboot is properly set to one of these values when
>> the mode bits indicate so.
>>
>> Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
>> ---
>>  board/xilinx/zynq/board.c | 6 ++++++
>>  1 file changed, 6 insertions(+)
>>
>> diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
>> index 5cd9bbf..cf80302 100644
>> --- a/board/xilinx/zynq/board.c
>> +++ b/board/xilinx/zynq/board.c
>> @@ -85,9 +85,15 @@ int board_init(void)
>>  int board_late_init(void)
>>  {
>>  	switch ((zynq_slcr_get_boot_mode()) & ZYNQ_BM_MASK) {
>> +	case ZYNQ_BM_QSPI:
>> +		setenv("modeboot", "qspiboot");
>> +		break;
>>  	case ZYNQ_BM_NOR:
>>  		setenv("modeboot", "norboot");
>>  		break;
>> +	case ZYNQ_BM_NAND:
>> +		setenv("modeboot", "nandboot");
>> +		break;
>>  	case ZYNQ_BM_SD:
>>  		setenv("modeboot", "sdboot");
>>  		break;
>>
>
> The same patch was merged some days ago. Please check latest master branch.
>
> Thanks,
> Michal
>



Kind regards,

Mike Looijmans
System Expert

TOPIC Products
Materiaalweg 4, NL-5681 RJ Best
Postbus 440, NL-5680 AK Best
Telefoon: +31 (0) 499 33 69 79
E-mail: mike.looijmans at topicproducts.com
Website: www.topicproducts.com

Please consider the environment before printing this e-mail