* No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
@ 2009-04-26 14:29 Tim Kaufmann
2009-04-26 14:51 ` Tim Kaufmann
2009-04-27 10:41 ` Christian Tramnitz
0 siblings, 2 replies; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-26 14:29 UTC (permalink / raw)
To: xen-devel
Hello,
my system: Intel DQ45CB with latest BIOS (0079 as of April 6th 2009)
and VT-d enabled, Core 2 Quad Q9550 (E0), 8 GB RAM.
Tested with OpenSuse 11.1, packaged Kernel/Xen 3.3 and kernel opts
"iommu=1", "iommu=1 msi=1", "dom0_mem=1024M iommu=1", "dom0_mem=1024M
iommu=1 msi=1". System freezes on boot, last messages displayed are
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
Installed Debian Lenny and compiled 2.6.18.8 / Xen 3.4rc3 - same
result as above.
I'd like to help debugging this, but I'd need someone to help me
setting up Serial-over-LAN with one of my other computers (Ubuntu 8.04
LTS, XP, Mac OS X 10.5).
Tim
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-26 14:29 No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB Tim Kaufmann
@ 2009-04-26 14:51 ` Tim Kaufmann
2009-04-26 21:04 ` Ross Philipson
2009-04-27 10:41 ` Christian Tramnitz
1 sibling, 1 reply; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-26 14:51 UTC (permalink / raw)
To: xen-devel
Am 26.04.2009 um 16:29 schrieb Tim Kaufmann:
> Installed Debian Lenny and compiled 2.6.18.8 / Xen 3.4rc3 - same
> result as above.
May be it's interesting to know the last messages before this setup
hangs:
(XEN) Brought up 4 CPUs
(XEN) Intel VT-d Snoop Control not supported.
(XEN) Intel VT-d DMA Passthrough not supported.
(XEN) Intel VT-d Queued Invalidation not supported.
(XEN) Intel VT-d Interrupt Remapping not supported.
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
(XEN) CPUIDLE: disabled due to no HPET. Force enable with "cpuidle".
The latter one disappears when I turn on HPET in BIOS.
Tim
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-26 14:51 ` Tim Kaufmann
@ 2009-04-26 21:04 ` Ross Philipson
2009-04-26 23:35 ` Tim Kaufmann
0 siblings, 1 reply; 28+ messages in thread
From: Ross Philipson @ 2009-04-26 21:04 UTC (permalink / raw)
To: Tim Kaufmann, xen-devel
> my system: Intel DQ45CB with latest BIOS (0079 as of April 6th 2009) and VT-d enabled, Core 2 Quad Q9550 (E0), 8 GB RAM.
You said it is an Intel system; is the over all system an OEM system or a custom assembly? Whose BIOS is ver 0079?
The trace below is much like the tail end of the trace we saw when we encountered a problem like this. Can you try using "iommu_inclusive_mapping=1" on the xen boot command line? This works around a VT-d related BIOS issue.
Thanks
Ross
-----Original Message-----
From: xen-devel-bounces@lists.xensource.com [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Tim Kaufmann
Sent: Sunday, April 26, 2009 10:51 AM
To: xen-devel
Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
Am 26.04.2009 um 16:29 schrieb Tim Kaufmann:
> Installed Debian Lenny and compiled 2.6.18.8 / Xen 3.4rc3 - same
> result as above.
May be it's interesting to know the last messages before this setup
hangs:
(XEN) Brought up 4 CPUs
(XEN) Intel VT-d Snoop Control not supported.
(XEN) Intel VT-d DMA Passthrough not supported.
(XEN) Intel VT-d Queued Invalidation not supported.
(XEN) Intel VT-d Interrupt Remapping not supported.
(XEN) I/O virtualisation enabled
(XEN) I/O virtualisation for PV guests disabled
(XEN) CPUIDLE: disabled due to no HPET. Force enable with "cpuidle".
The latter one disappears when I turn on HPET in BIOS.
Tim
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-26 21:04 ` Ross Philipson
@ 2009-04-26 23:35 ` Tim Kaufmann
2009-04-27 13:39 ` Ross Philipson
0 siblings, 1 reply; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-26 23:35 UTC (permalink / raw)
To: Ross Philipson; +Cc: xen-devel
> You said it is an Intel system; is the over all system an OEM system
> or a custom assembly?
It's a custom assembly and the BIOS ver 0079 belongs to the mainboard.
To be precise, here it is:
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&Inst=Yes&ProductID=2933&DwnldID=17562&strOSs=All&OSFullName=Alle%20Betriebssysteme&lang=deu
> Can you try using "iommu_inclusive_mapping=1" on the xen boot
> command line? This works around a VT-d related BIOS issue.
That didn't help. Now that I compiled Xen with debug options, the last
lines before the boot process hangs look like this:
(XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 1:1.0
This output is the same, no matter if I boot with iommu=1 only or with
both iommu and iommu_inclusive_mapping enabled.
Attached, there's a full xm dmesg of the machine after booting it with
IOMMU disabled.
Tim
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ \047_ \ |_ \| || |_| | | |__| \047__/ __| |_ \ __|
\047_ \| \047__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@xxxxxxxxxxxx) (gcc version 4.3.2
(Debian 4.3.2-1.1) ) Sun Apr 26 16:00:39 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: iommu_inclusive_mapping=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd3c1000 (usable)
(XEN) 00000000bd3c1000 - 00000000bd403000 (ACPI NVS)
(XEN) 00000000bd403000 - 00000000bd526000 (reserved)
(XEN) 00000000bd526000 - 00000000bd53a000 (ACPI NVS)
(XEN) 00000000bd53a000 - 00000000bd63c000 (reserved)
(XEN) 00000000bd63c000 - 00000000bd63d000 (ACPI NVS)
(XEN) 00000000bd63d000 - 00000000bd642000 (reserved)
(XEN) 00000000bd642000 - 00000000bd64c000 (ACPI data)
(XEN) 00000000bd64c000 - 00000000bd667000 (ACPI NVS)
(XEN) 00000000bd667000 - 00000000bd686000 (reserved)
(XEN) 00000000bd686000 - 00000000bd68c000 (ACPI NVS)
(XEN) 00000000bd68c000 - 00000000bd800000 (usable)
(XEN) 00000000bd800000 - 00000000bdb00000 (reserved)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8084MB (8278860kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD64AE18, 0064 (r1 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: FACP BD649D98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD642018, 6818 (r1 INTEL DQ45CB 4F INTL
20051117)
(XEN) ACPI: FACS BD652F40, 0040
(XEN) ACPI: APIC BD649F18, 006C (r2 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: MCFG BD654E18, 003C (r1 INTEL DQ45CB 4F
MSFT 97)
(XEN) ACPI: ASF! BD653D18, 00A0 (r32 INTEL DQ45CB 4F TFSM
F4240)
(XEN) ACPI: HPET BD654D98, 0038 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: SPCR BD654C98, 0050 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: TCPA BD654C18, 0032 (r2 INTEL DQ45CB 4F MSFT
1000013)
(XEN) ACPI: DMAR BD63CC18, 0120 (r1 INTEL DQ45CB 4F
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd652f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.098 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 14.318MHz HPET
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) microcode.c:73:d32767 microcode: CPU3 resumed
(XEN) Brought up 4 CPUs
(XEN) I/O virtualisation disabled
(XEN) HPET: 8 timers in total, 4 timers will be used for broadcast
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80200000 memsz=0x287a00
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80488000 memsz=0x8a8e8
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80513000 memsz=0xc08
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80514000 memsz=0xcd81c
(XEN) elf_parse_binary: memory: 0xffffffff80200000 -> 0xffffffff805e181c
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0xffffffff80000000
(XEN) elf_xen_parse_note: ENTRY = 0xffffffff80200000
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80206000
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: FEATURES = "writable_page_tables|
writable_descriptor_tables|auto_translated_physmap|pae_pgdir_above_4gb|
supervisor_mode_kernel"
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_addr_calc_check: addresses:
(XEN) virt_base = 0xffffffff80000000
(XEN) elf_paddr_offset = 0xffffffff80000000
(XEN) virt_offset = 0x0
(XEN) virt_kstart = 0xffffffff80200000
(XEN) virt_kend = 0xffffffff805e181c
(XEN) virt_entry = 0xffffffff80200000
(XEN) p2m_base = 0xffffffffffffffff
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, lsb, paddr 0xffffffff80200000 ->
0xffffffff805e181c
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000230000000->0000000234000000 (1994281
pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff80200000->ffffffff805e181c
(XEN) Init. ramdisk: ffffffff805e2000->ffffffff817a4800
(XEN) Phys-Mach map: ffffffff817a5000->ffffffff826fc148
(XEN) Start info: ffffffff826fd000->ffffffff826fd4b4
(XEN) Page tables: ffffffff826fe000->ffffffff82715000
(XEN) Boot stack: ffffffff82715000->ffffffff82716000
(XEN) TOTAL: ffffffff80000000->ffffffff82800000
(XEN) ENTRY ADDRESS: ffffffff80200000
(XEN) Dom0 has maximum 4 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 ->
0xffffffff80487a00
(XEN) elf_load_binary: phdr 1 at 0xffffffff80488000 ->
0xffffffff805128e8
(XEN) elf_load_binary: phdr 2 at 0xffffffff80513000 ->
0xffffffff80513c08
(XEN) elf_load_binary: phdr 3 at 0xffffffff80514000 ->
0xffffffff8054eff8
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three times to
switch input to Xen)
(XEN) Freed 128kB init memory.
(XEN) PCI add device 00:19.0
(XEN) PCI add device 00:03.2
(XEN) PCI add device 00:1f.5
(XEN) Set CPU acpi_id(1) cpuid(0) Px State info:
(XEN) _PPC: 0
(XEN) Set CPU acpi_id(1) cpuid(0) Px State info:
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=64,
bit_offset=0, reserved=0, address=409
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=16,
bit_offset=0, reserved=0, address=408
(XEN) _PSS: state_count=2
(XEN) State0: 2830MHz 27000mW 10us 10us 0x4822 0x4822
(XEN) State1: 1998MHz 13800mW 10us 10us 0x616 0x616
(XEN) _PSD: num_entries=5 rev=0 domain=1 coord_type=252
num_processors=1
(XEN) _PPC: 0
(XEN) xen_pminfo: @acpi_cpufreq_cpu_init,HARDWARE addr space
(XEN) CPU 0 initialization completed
(XEN) Set CPU acpi_id(2) cpuid(1) Px State info:
(XEN) _PPC: 0
(XEN) Set CPU acpi_id(2) cpuid(1) Px State info:
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=64,
bit_offset=0, reserved=0, address=409
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=16,
bit_offset=0, reserved=0, address=408
(XEN) _PSS: state_count=2
(XEN) State0: 2830MHz 27000mW 10us 10us 0x4822 0x4822
(XEN) State1: 1998MHz 13800mW 10us 10us 0x616 0x616
(XEN) _PSD: num_entries=5 rev=0 domain=2 coord_type=252
num_processors=1
(XEN) _PPC: 0
(XEN) xen_pminfo: @acpi_cpufreq_cpu_init,HARDWARE addr space
(XEN) CPU 1 initialization completed
(XEN) Set CPU acpi_id(3) cpuid(2) Px State info:
(XEN) _PPC: 0
(XEN) Set CPU acpi_id(3) cpuid(2) Px State info:
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=64,
bit_offset=0, reserved=0, address=409
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=16,
bit_offset=0, reserved=0, address=408
(XEN) _PSS: state_count=2
(XEN) State0: 2830MHz 27000mW 10us 10us 0x4822 0x4822
(XEN) State1: 1998MHz 13800mW 10us 10us 0x616 0x616
(XEN) _PSD: num_entries=5 rev=0 domain=3 coord_type=252
num_processors=1
(XEN) _PPC: 0
(XEN) xen_pminfo: @acpi_cpufreq_cpu_init,HARDWARE addr space
(XEN) CPU 2 initialization completed
(XEN) Set CPU acpi_id(4) cpuid(3) Px State info:
(XEN) _PPC: 0
(XEN) Set CPU acpi_id(4) cpuid(3) Px State info:
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=64,
bit_offset=0, reserved=0, address=409
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=16,
bit_offset=0, reserved=0, address=408
(XEN) _PSS: state_count=2
(XEN) State0: 2830MHz 27000mW 10us 10us 0x4822 0x4822
(XEN) State1: 1998MHz 13800mW 10us 10us 0x616 0x616
(XEN) _PSD: num_entries=5 rev=0 domain=4 coord_type=252
num_processors=1
(XEN) _PPC: 0
(XEN) xen_pminfo: @acpi_cpufreq_cpu_init,HARDWARE addr space
(XEN) CPU 3 initialization completed
(XEN) no cpu_id for acpi_id 5
(XEN) no cpu_id for acpi_id 6
(XEN) no cpu_id for acpi_id 7
(XEN) no cpu_id for acpi_id 8
(XEN) PCI add device 00:1a.0
(XEN) PCI add device 00:1a.1
(XEN) PCI add device 00:1a.2
(XEN) PCI add device 00:1d.0
(XEN) PCI add device 00:1d.1
(XEN) PCI add device 00:1d.2
(XEN) PCI add device 01:01.0
(XEN) PCI add device 01:00.0
(XEN) PCI add device 00:1f.2
(XEN) PCI add device 00:1a.7
(XEN) PCI add device 00:1d.7
(XEN) PCI add device 00:1f.5
(XEN) PCI add device 00:1f.3
(XEN) PCI add device 00:1b.0
(XEN) irq.c:640:d0 Cannot bind IRQ 2 to guest. In use by \047cascade
\047.
(XEN) irq.c:640:d0 Cannot bind IRQ 2 to guest. In use by \047cascade
\047.
(XEN) mtrr: type mismatch for c1fe0000,10000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1fc0000,20000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1f80000,40000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1f00000,80000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1e00000,100000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1c00000,200000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1800000,400000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1000000,800000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c0000000,1000000 old: write-back new:
write-combining
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-26 14:29 No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB Tim Kaufmann
2009-04-26 14:51 ` Tim Kaufmann
@ 2009-04-27 10:41 ` Christian Tramnitz
2009-04-27 11:16 ` Tim Kaufmann
1 sibling, 1 reply; 28+ messages in thread
From: Christian Tramnitz @ 2009-04-27 10:41 UTC (permalink / raw)
To: xen-devel
So what is your actual problem then?
> (XEN) I/O virtualisation enabled
This means VT-d is enabled.
If you are wondering about:
> (XEN) I/O virtualisation for PV guests disabled
You may want to have a look at iommu=pv if that is what you need...
Best regards,
Christian
Tim Kaufmann wrote:
> Hello,
>
> my system: Intel DQ45CB with latest BIOS (0079 as of April 6th 2009) and
> VT-d enabled, Core 2 Quad Q9550 (E0), 8 GB RAM.
>
> Tested with OpenSuse 11.1, packaged Kernel/Xen 3.3 and kernel opts
> "iommu=1", "iommu=1 msi=1", "dom0_mem=1024M iommu=1", "dom0_mem=1024M
> iommu=1 msi=1". System freezes on boot, last messages displayed are
>
> (XEN) I/O virtualisation enabled
> (XEN) I/O virtualisation for PV guests disabled
>
> Installed Debian Lenny and compiled 2.6.18.8 / Xen 3.4rc3 - same result
> as above.
>
> I'd like to help debugging this, but I'd need someone to help me setting
> up Serial-over-LAN with one of my other computers (Ubuntu 8.04 LTS, XP,
> Mac OS X 10.5).
>
> Tim
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 10:41 ` Christian Tramnitz
@ 2009-04-27 11:16 ` Tim Kaufmann
2009-04-27 14:51 ` Christian Tramnitz
0 siblings, 1 reply; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-27 11:16 UTC (permalink / raw)
To: Christian Tramnitz; +Cc: xen-devel
Am 27.04.2009 um 12:41 schrieb Christian Tramnitz:
> So what is your actual problem then?
As I wrote: I cannot boot with iommu=1 because the system freezes.
Tim
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-26 23:35 ` Tim Kaufmann
@ 2009-04-27 13:39 ` Ross Philipson
[not found] ` <F126C20F-9063-4FCC-BF8F-FE4CCDBCF1E5@taquiri.de>
0 siblings, 1 reply; 28+ messages in thread
From: Ross Philipson @ 2009-04-27 13:39 UTC (permalink / raw)
To: Tim Kaufmann; +Cc: xen-devel
Tim,
Could you send along a few things that might be helpful?
1. The rest of the xen output from your debug build leading up to the hang.
2. A listing of your PCI devices using lspci.
3. A dump of the ACPI DMAR using pmtools/acpidump - using something like this
$ acpidump -t DMAR -b > dmar.bin
Thanks
Ross
-----Original Message-----
From: Tim Kaufmann [mailto:tk@taquiri.de]
Sent: Sunday, April 26, 2009 7:36 PM
To: Ross Philipson
Cc: xen-devel
Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
> You said it is an Intel system; is the over all system an OEM system
> or a custom assembly?
It's a custom assembly and the BIOS ver 0079 belongs to the mainboard.
To be precise, here it is:
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&Inst=Yes&ProductID=2933&DwnldID=17562&strOSs=All&OSFullName=Alle%20Betriebssysteme&lang=deu
> Can you try using "iommu_inclusive_mapping=1" on the xen boot
> command line? This works around a VT-d related BIOS issue.
That didn't help. Now that I compiled Xen with debug options, the last
lines before the boot process hangs look like this:
(XEN) [VT-D]iommu.c:1252:d32767 domain_context_mapping:PCI: bdf = 1:1.0
This output is the same, no matter if I boot with iommu=1 only or with
both iommu and iommu_inclusive_mapping enabled.
Attached, there's a full xm dmesg of the machine after booting it with
IOMMU disabled.
Tim
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ \047_ \ |_ \| || |_| | | |__| \047__/ __| |_ \ __|
\047_ \| \047__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@xxxxxxxxxxxx) (gcc version 4.3.2
(Debian 4.3.2-1.1) ) Sun Apr 26 16:00:39 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: iommu_inclusive_mapping=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd3c1000 (usable)
(XEN) 00000000bd3c1000 - 00000000bd403000 (ACPI NVS)
(XEN) 00000000bd403000 - 00000000bd526000 (reserved)
(XEN) 00000000bd526000 - 00000000bd53a000 (ACPI NVS)
(XEN) 00000000bd53a000 - 00000000bd63c000 (reserved)
(XEN) 00000000bd63c000 - 00000000bd63d000 (ACPI NVS)
(XEN) 00000000bd63d000 - 00000000bd642000 (reserved)
(XEN) 00000000bd642000 - 00000000bd64c000 (ACPI data)
(XEN) 00000000bd64c000 - 00000000bd667000 (ACPI NVS)
(XEN) 00000000bd667000 - 00000000bd686000 (reserved)
(XEN) 00000000bd686000 - 00000000bd68c000 (ACPI NVS)
(XEN) 00000000bd68c000 - 00000000bd800000 (usable)
(XEN) 00000000bd800000 - 00000000bdb00000 (reserved)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8084MB (8278860kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD64AE18, 0064 (r1 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: FACP BD649D98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD642018, 6818 (r1 INTEL DQ45CB 4F INTL
20051117)
(XEN) ACPI: FACS BD652F40, 0040
(XEN) ACPI: APIC BD649F18, 006C (r2 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: MCFG BD654E18, 003C (r1 INTEL DQ45CB 4F
MSFT 97)
(XEN) ACPI: ASF! BD653D18, 00A0 (r32 INTEL DQ45CB 4F TFSM
F4240)
(XEN) ACPI: HPET BD654D98, 0038 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: SPCR BD654C98, 0050 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: TCPA BD654C18, 0032 (r2 INTEL DQ45CB 4F MSFT
1000013)
(XEN) ACPI: DMAR BD63CC18, 0120 (r1 INTEL DQ45CB 4F
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd652f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.098 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 14.318MHz HPET
(XEN) microcode.c:73:d32767 microcode: CPU1 resumed
(XEN) microcode.c:73:d32767 microcode: CPU2 resumed
(XEN) microcode.c:73:d32767 microcode: CPU3 resumed
(XEN) Brought up 4 CPUs
(XEN) I/O virtualisation disabled
(XEN) HPET: 8 timers in total, 4 timers will be used for broadcast
(XEN) ACPI sleep modes: S3
(XEN) mcheck_poll: Machine check polling timer started.
(XEN) *** LOADING DOMAIN 0 ***
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80200000 memsz=0x287a00
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80488000 memsz=0x8a8e8
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80513000 memsz=0xc08
(XEN) elf_parse_binary: phdr: paddr=0xffffffff80514000 memsz=0xcd81c
(XEN) elf_parse_binary: memory: 0xffffffff80200000 -> 0xffffffff805e181c
(XEN) elf_xen_parse_note: GUEST_OS = "linux"
(XEN) elf_xen_parse_note: GUEST_VERSION = "2.6"
(XEN) elf_xen_parse_note: XEN_VERSION = "xen-3.0"
(XEN) elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000
(XEN) elf_xen_parse_note: PADDR_OFFSET = 0xffffffff80000000
(XEN) elf_xen_parse_note: ENTRY = 0xffffffff80200000
(XEN) elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff80206000
(XEN) elf_xen_parse_note: unknown xen elf note (0xd)
(XEN) elf_xen_parse_note: FEATURES = "writable_page_tables|
writable_descriptor_tables|auto_translated_physmap|pae_pgdir_above_4gb|
supervisor_mode_kernel"
(XEN) elf_xen_parse_note: LOADER = "generic"
(XEN) elf_xen_parse_note: SUSPEND_CANCEL = 0x1
(XEN) elf_xen_addr_calc_check: addresses:
(XEN) virt_base = 0xffffffff80000000
(XEN) elf_paddr_offset = 0xffffffff80000000
(XEN) virt_offset = 0x0
(XEN) virt_kstart = 0xffffffff80200000
(XEN) virt_kend = 0xffffffff805e181c
(XEN) virt_entry = 0xffffffff80200000
(XEN) p2m_base = 0xffffffffffffffff
(XEN) Xen kernel: 64-bit, lsb, compat32
(XEN) Dom0 kernel: 64-bit, lsb, paddr 0xffffffff80200000 ->
0xffffffff805e181c
(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN) Dom0 alloc.: 0000000230000000->0000000234000000 (1994281
pages to be allocated)
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN) Loaded kernel: ffffffff80200000->ffffffff805e181c
(XEN) Init. ramdisk: ffffffff805e2000->ffffffff817a4800
(XEN) Phys-Mach map: ffffffff817a5000->ffffffff826fc148
(XEN) Start info: ffffffff826fd000->ffffffff826fd4b4
(XEN) Page tables: ffffffff826fe000->ffffffff82715000
(XEN) Boot stack: ffffffff82715000->ffffffff82716000
(XEN) TOTAL: ffffffff80000000->ffffffff82800000
(XEN) ENTRY ADDRESS: ffffffff80200000
(XEN) Dom0 has maximum 4 VCPUs
(XEN) elf_load_binary: phdr 0 at 0xffffffff80200000 ->
0xffffffff80487a00
(XEN) elf_load_binary: phdr 1 at 0xffffffff80488000 ->
0xffffffff805128e8
(XEN) elf_load_binary: phdr 2 at 0xffffffff80513000 ->
0xffffffff80513c08
(XEN) elf_load_binary: phdr 3 at 0xffffffff80514000 ->
0xffffffff8054eff8
(XEN) Scrubbing Free RAM: .done.
(XEN) Xen trace buffers: disabled
(XEN) Std. Loglevel: All
(XEN) Guest Loglevel: All
(XEN) Xen is relinquishing VGA console.
(XEN) *** Serial input -> DOM0 (type \047CTRL-a\047 three times to
switch input to Xen)
(XEN) Freed 128kB init memory.
(XEN) PCI add device 00:19.0
(XEN) PCI add device 00:03.2
(XEN) PCI add device 00:1f.5
(XEN) Set CPU acpi_id(1) cpuid(0) Px State info:
(XEN) _PPC: 0
(XEN) Set CPU acpi_id(1) cpuid(0) Px State info:
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=64,
bit_offset=0, reserved=0, address=409
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=16,
bit_offset=0, reserved=0, address=408
(XEN) _PSS: state_count=2
(XEN) State0: 2830MHz 27000mW 10us 10us 0x4822 0x4822
(XEN) State1: 1998MHz 13800mW 10us 10us 0x616 0x616
(XEN) _PSD: num_entries=5 rev=0 domain=1 coord_type=252
num_processors=1
(XEN) _PPC: 0
(XEN) xen_pminfo: @acpi_cpufreq_cpu_init,HARDWARE addr space
(XEN) CPU 0 initialization completed
(XEN) Set CPU acpi_id(2) cpuid(1) Px State info:
(XEN) _PPC: 0
(XEN) Set CPU acpi_id(2) cpuid(1) Px State info:
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=64,
bit_offset=0, reserved=0, address=409
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=16,
bit_offset=0, reserved=0, address=408
(XEN) _PSS: state_count=2
(XEN) State0: 2830MHz 27000mW 10us 10us 0x4822 0x4822
(XEN) State1: 1998MHz 13800mW 10us 10us 0x616 0x616
(XEN) _PSD: num_entries=5 rev=0 domain=2 coord_type=252
num_processors=1
(XEN) _PPC: 0
(XEN) xen_pminfo: @acpi_cpufreq_cpu_init,HARDWARE addr space
(XEN) CPU 1 initialization completed
(XEN) Set CPU acpi_id(3) cpuid(2) Px State info:
(XEN) _PPC: 0
(XEN) Set CPU acpi_id(3) cpuid(2) Px State info:
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=64,
bit_offset=0, reserved=0, address=409
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=16,
bit_offset=0, reserved=0, address=408
(XEN) _PSS: state_count=2
(XEN) State0: 2830MHz 27000mW 10us 10us 0x4822 0x4822
(XEN) State1: 1998MHz 13800mW 10us 10us 0x616 0x616
(XEN) _PSD: num_entries=5 rev=0 domain=3 coord_type=252
num_processors=1
(XEN) _PPC: 0
(XEN) xen_pminfo: @acpi_cpufreq_cpu_init,HARDWARE addr space
(XEN) CPU 2 initialization completed
(XEN) Set CPU acpi_id(4) cpuid(3) Px State info:
(XEN) _PPC: 0
(XEN) Set CPU acpi_id(4) cpuid(3) Px State info:
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=64,
bit_offset=0, reserved=0, address=409
(XEN) _PCT: descriptor=130, length=12, space_id=127, bit_width=16,
bit_offset=0, reserved=0, address=408
(XEN) _PSS: state_count=2
(XEN) State0: 2830MHz 27000mW 10us 10us 0x4822 0x4822
(XEN) State1: 1998MHz 13800mW 10us 10us 0x616 0x616
(XEN) _PSD: num_entries=5 rev=0 domain=4 coord_type=252
num_processors=1
(XEN) _PPC: 0
(XEN) xen_pminfo: @acpi_cpufreq_cpu_init,HARDWARE addr space
(XEN) CPU 3 initialization completed
(XEN) no cpu_id for acpi_id 5
(XEN) no cpu_id for acpi_id 6
(XEN) no cpu_id for acpi_id 7
(XEN) no cpu_id for acpi_id 8
(XEN) PCI add device 00:1a.0
(XEN) PCI add device 00:1a.1
(XEN) PCI add device 00:1a.2
(XEN) PCI add device 00:1d.0
(XEN) PCI add device 00:1d.1
(XEN) PCI add device 00:1d.2
(XEN) PCI add device 01:01.0
(XEN) PCI add device 01:00.0
(XEN) PCI add device 00:1f.2
(XEN) PCI add device 00:1a.7
(XEN) PCI add device 00:1d.7
(XEN) PCI add device 00:1f.5
(XEN) PCI add device 00:1f.3
(XEN) PCI add device 00:1b.0
(XEN) irq.c:640:d0 Cannot bind IRQ 2 to guest. In use by \047cascade
\047.
(XEN) irq.c:640:d0 Cannot bind IRQ 2 to guest. In use by \047cascade
\047.
(XEN) mtrr: type mismatch for c1fe0000,10000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1fc0000,20000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1f80000,40000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1f00000,80000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1e00000,100000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1c00000,200000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1800000,400000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c1000000,800000 old: write-back new:
write-combining
(XEN) mtrr: type mismatch for c0000000,1000000 old: write-back new:
write-combining
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 11:16 ` Tim Kaufmann
@ 2009-04-27 14:51 ` Christian Tramnitz
0 siblings, 0 replies; 28+ messages in thread
From: Christian Tramnitz @ 2009-04-27 14:51 UTC (permalink / raw)
To: xen-devel
Tim Kaufmann wrote:
> As I wrote: I cannot boot with iommu=1 because the system freezes.
Sorry I should have paid more attention on the actual text and not just
to the topic.
Have you tried any of the "no-" params yet (no-snoop, no-qinval,
no-intremap)?
It could also be related to powersaving, could you disable (xen-)cpuidle
for testing?
Best regards,
Christian
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
[not found] ` <831D55AF5A11D64C9B4B43F59EEBF72035FCB540F1@FTLPMAILBOX02.citrite.net>
@ 2009-04-27 16:48 ` Tim Kaufmann
2009-04-27 18:00 ` Ross Philipson
0 siblings, 1 reply; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-27 16:48 UTC (permalink / raw)
To: Ross Philipson; +Cc: xen-devel
I sent the requested files to Ross, now we're working on getting the
Serial-over-LAN (SOL) to work so I can capture the boot messages.
The board has two COM ports. One does not have a standard connector.
It's only a couple of pins directly on the board, so we can't use this
without getting a connector for it. I turned that one off in the BIOS.
lspci still shows the "serial KT controller", so this must be the COM-
Port created by AMT/SOL. The board's manual states, that the SOL-Port
is Com4 by the way.
As the data is sent via Ethernet, the USB-to-Serial-Converter and the
Nullmodem-Cable probably won't be useful. I downloaded the AMT-SDK
from intel.com and successfully connected to the AMT-Stack on the Xen-
PC. I can start a SOL-Console - now what? :-)
Tim
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 16:48 ` Tim Kaufmann
@ 2009-04-27 18:00 ` Ross Philipson
2009-04-27 18:31 ` Tim Kaufmann
0 siblings, 1 reply; 28+ messages in thread
From: Ross Philipson @ 2009-04-27 18:00 UTC (permalink / raw)
To: Tim Kaufmann; +Cc: xen-devel
So I haven't tried the AMT SOL stuff before but you may be able to setup the AMT commander/director tools (AMT Developer Toolkit) to get the SOL output. You will probably have to do some AMT provisioning to be able to connect the tools. Then you can setup the xen command line to do serial tracing - try it first with COM4. Also can you send a more verbose lspci trace (lspci -vv e.g.)?
Thanks
Ross
-----Original Message-----
From: Tim Kaufmann [mailto:tk@taquiri.de]
Sent: Monday, April 27, 2009 12:48 PM
To: Ross Philipson
Cc: xen-devel
Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
I sent the requested files to Ross, now we're working on getting the
Serial-over-LAN (SOL) to work so I can capture the boot messages.
The board has two COM ports. One does not have a standard connector.
It's only a couple of pins directly on the board, so we can't use this
without getting a connector for it. I turned that one off in the BIOS.
lspci still shows the "serial KT controller", so this must be the COM-
Port created by AMT/SOL. The board's manual states, that the SOL-Port
is Com4 by the way.
As the data is sent via Ethernet, the USB-to-Serial-Converter and the
Nullmodem-Cable probably won't be useful. I downloaded the AMT-SDK
from intel.com and successfully connected to the AMT-Stack on the Xen-
PC. I can start a SOL-Console - now what? :-)
Tim
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 18:00 ` Ross Philipson
@ 2009-04-27 18:31 ` Tim Kaufmann
2009-04-27 18:39 ` Ross Philipson
0 siblings, 1 reply; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-27 18:31 UTC (permalink / raw)
To: Ross Philipson; +Cc: xen-devel
> connect the tools.
Done.
> Then you can setup the xen command line to do serial tracing - try
> it first with COM4.
A hint on how to *properly* set this up would be very welcome.
> Also can you send a more verbose lspci trace (lspci -vv e.g.)?
Attached.
Tim
automatix:~# lspci -vv
00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM
Controller (rev 03)
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset
Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at e220 [size=8]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation 4 Series Chipset
Integrated Graphics Controller (rev 03)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0400000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 Communication controller: Intel Corporation 4 Series Chipset
HECI Controller (rev 03)
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0627100 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:03.2 IDE interface: Intel Corporation 4 Series Chipset PT IDER
Controller (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at e210 [size=8]
Region 1: I/O ports at e200 [size=4]
Region 2: I/O ports at e1f0 [size=8]
Region 3: I/O ports at e1e0 [size=4]
Region 4: I/O ports at e1d0 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:03.3 Serial controller: Intel Corporation 4 Series Chipset Serial
KT Controller (rev 03) (prog-if 02 [16550])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 3
Region 0: I/O ports at e1c0 [size=8]
Region 1: Memory at d0625000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:19.0 Ethernet controller: Intel Corporation 82567LM-3 Gigabit
Network Connection (rev 02)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 255
Region 0: Memory at d0600000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at d0624000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at e100 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable+
Address: 00000000fee0100c Data: 41c0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: e1000e
00:1a.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #4
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at e0e0 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #5
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at e0c0 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #6
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at e0a0 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller
#2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 0: Memory at d0626c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] Vendor Specific Information <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation ICH10 HD Audio Controller (rev
02)
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d0620000 (64-bit, non-prefetchable) [disabled]
[size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive-
BWMgmt- ABWMgmt-
Kernel modules: snd-hda-intel
00:1d.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #1
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at e080 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #2
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at e060 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #3
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at e040 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller
#1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0626800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] Vendor Specific Information <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a2) (prog-
if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: d0500000-d05fffff
Prefetchable memory behind bridge: 00000000d0700000-00000000d07fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Gammagraphx, Inc. Device 0000
00:1f.0 ISA bridge: Intel Corporation ICH10 LPC Interface Controller
(rev 02)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
00:1f.2 SATA controller: Intel Corporation ICH10 6 port SATA AHCI
Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 254
Region 0: I/O ports at e1b0 [size=8]
Region 1: I/O ports at e1a0 [size=4]
Region 2: I/O ports at e190 [size=8]
Region 3: I/O ports at e180 [size=4]
Region 4: I/O ports at e020 [size=32]
Region 5: Memory at d0626000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/3 Enable+
Address: fee0100c Data: 4139
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] Vendor Specific Information <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation ICH10 SMBus Controller (rev 02)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at d0627000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at e000 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00:1f.5 IDE interface: Intel Corporation ICH10 2 port SATA IDE
Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at e170 [size=8]
Region 1: I/O ports at e160 [size=4]
Region 2: I/O ports at e150 [size=8]
Region 3: I/O ports at e140 [size=4]
Region 4: I/O ports at e130 [size=16]
Region 5: I/O ports at e120 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information <?>
Kernel driver in use: ata_piix
Kernel modules: ata_piix
01:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado]
(rev 78)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC
Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at d000 [size=128]
Region 1: Memory at d0521100 (32-bit, non-prefetchable) [size=128]
Expansion ROM at d0700000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: 3c59x
Kernel modules: 3c59x
01:01.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 70) (prog-if 10
[OHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d0520000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at d0521000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot
+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 18:31 ` Tim Kaufmann
@ 2009-04-27 18:39 ` Ross Philipson
2009-04-27 19:01 ` Pasi Kärkkäinen
0 siblings, 1 reply; 28+ messages in thread
From: Ross Philipson @ 2009-04-27 18:39 UTC (permalink / raw)
To: Tim Kaufmann; +Cc: xen-devel
So using com4, you will need something like this:
xen.gz console=com4 com4=115200,8n1,0xe1c0,0
Note that 0xe1c0 is the IO port for the KT Controller below. Give that a shot. I am interested to see if this works since this would be a useful method of debugging.
Thanks
Ross
-----Original Message-----
From: Tim Kaufmann [mailto:tk@taquiri.de]
Sent: Monday, April 27, 2009 2:31 PM
To: Ross Philipson
Cc: xen-devel
Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
> connect the tools.
Done.
> Then you can setup the xen command line to do serial tracing - try
> it first with COM4.
A hint on how to *properly* set this up would be very welcome.
> Also can you send a more verbose lspci trace (lspci -vv e.g.)?
Attached.
Tim
automatix:~# lspci -vv
00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM
Controller (rev 03)
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset
Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at e220 [size=8]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation 4 Series Chipset
Integrated Graphics Controller (rev 03)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0400000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 Communication controller: Intel Corporation 4 Series Chipset
HECI Controller (rev 03)
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0627100 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:03.2 IDE interface: Intel Corporation 4 Series Chipset PT IDER
Controller (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at e210 [size=8]
Region 1: I/O ports at e200 [size=4]
Region 2: I/O ports at e1f0 [size=8]
Region 3: I/O ports at e1e0 [size=4]
Region 4: I/O ports at e1d0 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:03.3 Serial controller: Intel Corporation 4 Series Chipset Serial
KT Controller (rev 03) (prog-if 02 [16550])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 3
Region 0: I/O ports at e1c0 [size=8]
Region 1: Memory at d0625000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:19.0 Ethernet controller: Intel Corporation 82567LM-3 Gigabit
Network Connection (rev 02)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 255
Region 0: Memory at d0600000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at d0624000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at e100 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable+
Address: 00000000fee0100c Data: 41c0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: e1000e
00:1a.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #4
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at e0e0 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #5
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at e0c0 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #6
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at e0a0 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller
#2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 0: Memory at d0626c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] Vendor Specific Information <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation ICH10 HD Audio Controller (rev
02)
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d0620000 (64-bit, non-prefetchable) [disabled]
[size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI
00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive-
BWMgmt- ABWMgmt-
Kernel modules: snd-hda-intel
00:1d.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #1
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at e080 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #2
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at e060 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #3
(rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at e040 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller
#1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0626800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] Vendor Specific Information <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a2) (prog-
if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: d0500000-d05fffff
Prefetchable memory behind bridge: 00000000d0700000-00000000d07fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Gammagraphx, Inc. Device 0000
00:1f.0 ISA bridge: Intel Corporation ICH10 LPC Interface Controller
(rev 02)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
00:1f.2 SATA controller: Intel Corporation ICH10 6 port SATA AHCI
Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 254
Region 0: I/O ports at e1b0 [size=8]
Region 1: I/O ports at e1a0 [size=4]
Region 2: I/O ports at e190 [size=8]
Region 3: I/O ports at e180 [size=4]
Region 4: I/O ports at e020 [size=32]
Region 5: Memory at d0626000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/3 Enable+
Address: fee0100c Data: 4139
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] Vendor Specific Information <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation ICH10 SMBus Controller (rev 02)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at d0627000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at e000 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00:1f.5 IDE interface: Intel Corporation ICH10 2 port SATA IDE
Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at e170 [size=8]
Region 1: I/O ports at e160 [size=4]
Region 2: I/O ports at e150 [size=8]
Region 3: I/O ports at e140 [size=4]
Region 4: I/O ports at e130 [size=16]
Region 5: I/O ports at e120 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information <?>
Kernel driver in use: ata_piix
Kernel modules: ata_piix
01:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado]
(rev 78)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC
Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at d000 [size=128]
Region 1: Memory at d0521100 (32-bit, non-prefetchable) [size=128]
Expansion ROM at d0700000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: 3c59x
Kernel modules: 3c59x
01:01.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 70) (prog-if 10
[OHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d0520000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at d0521000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot
+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 18:39 ` Ross Philipson
@ 2009-04-27 19:01 ` Pasi Kärkkäinen
2009-04-27 19:07 ` Ross Philipson
0 siblings, 1 reply; 28+ messages in thread
From: Pasi Kärkkäinen @ 2009-04-27 19:01 UTC (permalink / raw)
To: Ross Philipson; +Cc: Tim Kaufmann, xen-devel
On Mon, Apr 27, 2009 at 02:39:40PM -0400, Ross Philipson wrote:
> So using com4, you will need something like this:
>
> xen.gz console=com4 com4=115200,8n1,0xe1c0,0
>
> Note that 0xe1c0 is the IO port for the KT Controller below. Give that a shot. I am interested to see if this works since this would be a useful method of debugging.
>
This is my DQ35JO configuration for AMT/SOL remote console (that server is NOT running Xen though):
grub.conf:
# Intel AMT serial-over-lan console
serial --port=0x3440 --speed=115200
terminal --timeout=10 console serial
kernel /vmlinuz-2.6.18-128.1.6.el5 ro root=.. console=ttyS1,115200n8 console=tty0
0x3440 is the IOport for AMT serial port from lspci.
Linux detects DQ35JO AMT serial port as ttyS1.
Then I connect to the serial console from a Linux desktop using "gamt" tool.
Hopefully that helps.
-- Pasi
> Thanks
> Ross
>
> -----Original Message-----
> From: Tim Kaufmann [mailto:tk@taquiri.de]
> Sent: Monday, April 27, 2009 2:31 PM
> To: Ross Philipson
> Cc: xen-devel
> Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
>
>
> > connect the tools.
>
> Done.
>
> > Then you can setup the xen command line to do serial tracing - try
> > it first with COM4.
>
> A hint on how to *properly* set this up would be very welcome.
>
> > Also can you send a more verbose lspci trace (lspci -vv e.g.)?
>
> Attached.
>
> Tim
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 19:01 ` Pasi Kärkkäinen
@ 2009-04-27 19:07 ` Ross Philipson
2009-04-27 21:15 ` Tim Kaufmann
0 siblings, 1 reply; 28+ messages in thread
From: Ross Philipson @ 2009-04-27 19:07 UTC (permalink / raw)
To: Pasi Kärkkäinen; +Cc: Tim Kaufmann, xen-devel
Cool, thanks. So maybe xen will just see it as com1 - Tim, you can try that instead of com4 but you will still have to specify the IO port for xen as below.
Thanks
Ross
-----Original Message-----
From: Pasi Kärkkäinen [mailto:pasik@iki.fi]
Sent: Monday, April 27, 2009 3:02 PM
To: Ross Philipson
Cc: Tim Kaufmann; xen-devel
Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
On Mon, Apr 27, 2009 at 02:39:40PM -0400, Ross Philipson wrote:
> So using com4, you will need something like this:
>
> xen.gz console=com4 com4=115200,8n1,0xe1c0,0
>
> Note that 0xe1c0 is the IO port for the KT Controller below. Give that a shot. I am interested to see if this works since this would be a useful method of debugging.
>
This is my DQ35JO configuration for AMT/SOL remote console (that server is NOT running Xen though):
grub.conf:
# Intel AMT serial-over-lan console
serial --port=0x3440 --speed=115200
terminal --timeout=10 console serial
kernel /vmlinuz-2.6.18-128.1.6.el5 ro root=.. console=ttyS1,115200n8 console=tty0
0x3440 is the IOport for AMT serial port from lspci.
Linux detects DQ35JO AMT serial port as ttyS1.
Then I connect to the serial console from a Linux desktop using "gamt" tool.
Hopefully that helps.
-- Pasi
> Thanks
> Ross
>
> -----Original Message-----
> From: Tim Kaufmann [mailto:tk@taquiri.de]
> Sent: Monday, April 27, 2009 2:31 PM
> To: Ross Philipson
> Cc: xen-devel
> Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
>
>
> > connect the tools.
>
> Done.
>
> > Then you can setup the xen command line to do serial tracing - try
> > it first with COM4.
>
> A hint on how to *properly* set this up would be very welcome.
>
> > Also can you send a more verbose lspci trace (lspci -vv e.g.)?
>
> Attached.
>
> Tim
>
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 19:07 ` Ross Philipson
@ 2009-04-27 21:15 ` Tim Kaufmann
2009-04-27 21:23 ` Ross Philipson
2009-04-28 17:56 ` Ross Philipson
0 siblings, 2 replies; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-27 21:15 UTC (permalink / raw)
To: Ross Philipson; +Cc: xen-devel
Got SOL workin'.
Grub looks like this:
title Xen 3.4.0-rc3-pre / Debian GNU/Linux, kernel 2.6.18.8-
xen
root (hd0,0)
kernel /xen-3.4.0-rc3-pre.gz console=com1
com1=115200,8n1,0xe1c0,0
module /vmlinuz-2.6.18.8-xen root=/dev/mapper/raidvg-lv--
dom0--root ro console=tty0
module /initrd.img-2.6.18.8-xen
I'm using amtterm on the client machine. It's in Debian testing
currently, but can easily be downloaded and installed via dpkg -i in
Ubuntu 8.04 LTS.
I connected to AMT with
amtterm -u admin -p supersecretpassword 10.11.1.31
As soon as I rebooted the AMT computer the client was receiving data.
Attached is the output of booting with iommu=1. For reasons unknown,
the lines I quoted as an example a couple of mails ago aren't in there.
Tim
Some tags for Google: Xen SOL Serial over LAN Intel AMT Console DQ45CB
root@obelix:~# amtterm -u admin -p ****** 10.11.1.31
amtterm: NONE -> CONNECT (connection to host)
ipv4 10.11.1.31 [10.11.1.31] 16994 open
amtterm: CONNECT -> INIT (redirection initialization)
amtterm: INIT -> AUTH (session authentication)
amtterm: AUTH -> INIT_SOL (serial-over-lan initialization)
amtterm: INIT_SOL -> RUN_SOL (serial-over-lan active)
serial-over-lan redirection ok
connected now, use ^] to escape
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ '_ \ |_ \| || |_| | | |__| '__/ __| |_ \ __| '_ \|
'__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@taquiri.dyndns.org) (gcc version
4.3.2 (Debian 4.3.2-1.1) ) Sun Apr 26 16:00:39 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6c1000 (usable)
(XEN) 00000000bd6c1000 - 00000000bd703000 (ACPI NVS)
(XEN) 00000000bd703000 - 00000000bd826000 (reserved)
(XEN) 00000000bd826000 - 00000000bd83a000 (ACPI NVS)
(XEN) 00000000bd83a000 - 00000000bd93c000 (reserved)
(XEN) 00000000bd93c000 - 00000000bd93d000 (ACPI NVS)
(XEN) 00000000bd93d000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd94c000 (ACPI data)
(XEN) 00000000bd94c000 - 00000000bd967000 (ACPI NVS)
(XEN) 00000000bd967000 - 00000000bd986000 (reserved)
(XEN) 00000000bd986000 - 00000000bd98c000 (ACPI NVS)
(XEN) 00000000bd98c000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8087MB (8281932kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD94AE18, 005C (r1 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: FACP BD949D98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD942018, 6818 (r1 INTEL DQ45CB 4F INTL
20051117)
(XEN) ACPI: FACS BD952F40, 0040
(XEN) ACPI: APIC BD949F18, 006C (r2 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: MCFG BD954E18, 003C (r1 INTEL DQ45CB 4F
MSFT 97)
(XEN) ACPI: ASF! BD953D18, 00A0 (r32 INTEL DQ45CB 4F TFSM
F4240)
(XEN) ACPI: SPCR BD954D18, 0050 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: TCPA BD954C98, 0032 (r2 INTEL DQ45CB 4F MSFT
1000013)
(XEN) ACPI: DMAR BD93CC18, 0120 (r1 INTEL DQ45CB 4F
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd952f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:485: Host address width 36
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed91000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed92000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed93000
(XEN) [VT-D]dmar.c:358: found INCLUDE_ALL
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base
= bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter
may be needed.
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.099 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 21:15 ` Tim Kaufmann
@ 2009-04-27 21:23 ` Ross Philipson
2009-04-28 17:56 ` Ross Philipson
1 sibling, 0 replies; 28+ messages in thread
From: Ross Philipson @ 2009-04-27 21:23 UTC (permalink / raw)
To: Tim Kaufmann; +Cc: xen-devel
That is cool that SOL worked easily. I just found that Fedora had the AMT sol client gamt that was mentioned earlier. I will have to try it out.
I will check some of the stuff out that you sent. One thing that jumped right out:
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base
= bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter
That looks like an invalid RMRR value so there are probably some issues with this particular BIOS version. Though the iommu_inclusive_mapping=1 should have gotten you by that issue if it was causing the hang so there are probably other problems.
Thanks
Ross
-----Original Message-----
From: Tim Kaufmann [mailto:tk@taquiri.de]
Sent: Monday, April 27, 2009 5:16 PM
To: Ross Philipson
Cc: Pasi Kärkkäinen; xen-devel
Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
Got SOL workin'.
Grub looks like this:
title Xen 3.4.0-rc3-pre / Debian GNU/Linux, kernel 2.6.18.8-
xen
root (hd0,0)
kernel /xen-3.4.0-rc3-pre.gz console=com1
com1=115200,8n1,0xe1c0,0
module /vmlinuz-2.6.18.8-xen root=/dev/mapper/raidvg-lv--
dom0--root ro console=tty0
module /initrd.img-2.6.18.8-xen
I'm using amtterm on the client machine. It's in Debian testing
currently, but can easily be downloaded and installed via dpkg -i in
Ubuntu 8.04 LTS.
I connected to AMT with
amtterm -u admin -p supersecretpassword 10.11.1.31
As soon as I rebooted the AMT computer the client was receiving data.
Attached is the output of booting with iommu=1. For reasons unknown,
the lines I quoted as an example a couple of mails ago aren't in there.
Tim
Some tags for Google: Xen SOL Serial over LAN Intel AMT Console DQ45CB
root@obelix:~# amtterm -u admin -p ****** 10.11.1.31
amtterm: NONE -> CONNECT (connection to host)
ipv4 10.11.1.31 [10.11.1.31] 16994 open
amtterm: CONNECT -> INIT (redirection initialization)
amtterm: INIT -> AUTH (session authentication)
amtterm: AUTH -> INIT_SOL (serial-over-lan initialization)
amtterm: INIT_SOL -> RUN_SOL (serial-over-lan active)
serial-over-lan redirection ok
connected now, use ^] to escape
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ '_ \ |_ \| || |_| | | |__| '__/ __| |_ \ __| '_ \|
'__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@taquiri.dyndns.org) (gcc version
4.3.2 (Debian 4.3.2-1.1) ) Sun Apr 26 16:00:39 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6c1000 (usable)
(XEN) 00000000bd6c1000 - 00000000bd703000 (ACPI NVS)
(XEN) 00000000bd703000 - 00000000bd826000 (reserved)
(XEN) 00000000bd826000 - 00000000bd83a000 (ACPI NVS)
(XEN) 00000000bd83a000 - 00000000bd93c000 (reserved)
(XEN) 00000000bd93c000 - 00000000bd93d000 (ACPI NVS)
(XEN) 00000000bd93d000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd94c000 (ACPI data)
(XEN) 00000000bd94c000 - 00000000bd967000 (ACPI NVS)
(XEN) 00000000bd967000 - 00000000bd986000 (reserved)
(XEN) 00000000bd986000 - 00000000bd98c000 (ACPI NVS)
(XEN) 00000000bd98c000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8087MB (8281932kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD94AE18, 005C (r1 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: FACP BD949D98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD942018, 6818 (r1 INTEL DQ45CB 4F INTL
20051117)
(XEN) ACPI: FACS BD952F40, 0040
(XEN) ACPI: APIC BD949F18, 006C (r2 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: MCFG BD954E18, 003C (r1 INTEL DQ45CB 4F
MSFT 97)
(XEN) ACPI: ASF! BD953D18, 00A0 (r32 INTEL DQ45CB 4F TFSM
F4240)
(XEN) ACPI: SPCR BD954D18, 0050 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: TCPA BD954C98, 0032 (r2 INTEL DQ45CB 4F MSFT
1000013)
(XEN) ACPI: DMAR BD93CC18, 0120 (r1 INTEL DQ45CB 4F
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd952f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:485: Host address width 36
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed91000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed92000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed93000
(XEN) [VT-D]dmar.c:358: found INCLUDE_ALL
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base
= bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter
may be needed.
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.099 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-27 21:15 ` Tim Kaufmann
2009-04-27 21:23 ` Ross Philipson
@ 2009-04-28 17:56 ` Ross Philipson
2009-04-29 23:47 ` Tim Kaufmann
1 sibling, 1 reply; 28+ messages in thread
From: Ross Philipson @ 2009-04-28 17:56 UTC (permalink / raw)
To: Tim Kaufmann; +Cc: xen-devel
[-- Attachment #1: Type: text/plain, Size: 10093 bytes --]
Attached is a textual version of your DMAR and some notes. In notes.txt at the bottom I noted that both RMRRs seem to have some issues but the iommu_inclusive_mapping=1 should have handled them. The rest of the DMAR looks OK to me. There are the DRHDs that I would expect to see for AUDIO, GFX, AMT/ME, and the INCLUDE_ALL.
So from what I see and what is in the logs, I am not sure. You said the BIOS you have is the latest - did you check with Intel to see if there are any known issues?
Thanks
Ross
-----Original Message-----
From: Tim Kaufmann [mailto:tk@taquiri.de]
Sent: Monday, April 27, 2009 5:16 PM
To: Ross Philipson
Cc: Pasi Kärkkäinen; xen-devel
Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
Got SOL workin'.
Grub looks like this:
title Xen 3.4.0-rc3-pre / Debian GNU/Linux, kernel 2.6.18.8-
xen
root (hd0,0)
kernel /xen-3.4.0-rc3-pre.gz console=com1
com1=115200,8n1,0xe1c0,0
module /vmlinuz-2.6.18.8-xen root=/dev/mapper/raidvg-lv--
dom0--root ro console=tty0
module /initrd.img-2.6.18.8-xen
I'm using amtterm on the client machine. It's in Debian testing
currently, but can easily be downloaded and installed via dpkg -i in
Ubuntu 8.04 LTS.
I connected to AMT with
amtterm -u admin -p supersecretpassword 10.11.1.31
As soon as I rebooted the AMT computer the client was receiving data.
Attached is the output of booting with iommu=1. For reasons unknown,
the lines I quoted as an example a couple of mails ago aren't in there.
Tim
Some tags for Google: Xen SOL Serial over LAN Intel AMT Console DQ45CB
root@obelix:~# amtterm -u admin -p ****** 10.11.1.31
amtterm: NONE -> CONNECT (connection to host)
ipv4 10.11.1.31 [10.11.1.31] 16994 open
amtterm: CONNECT -> INIT (redirection initialization)
amtterm: INIT -> AUTH (session authentication)
amtterm: AUTH -> INIT_SOL (serial-over-lan initialization)
amtterm: INIT_SOL -> RUN_SOL (serial-over-lan active)
serial-over-lan redirection ok
connected now, use ^] to escape
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ '_ \ |_ \| || |_| | | |__| '__/ __| |_ \ __| '_ \|
'__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@taquiri.dyndns.org) (gcc version
4.3.2 (Debian 4.3.2-1.1) ) Sun Apr 26 16:00:39 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6c1000 (usable)
(XEN) 00000000bd6c1000 - 00000000bd703000 (ACPI NVS)
(XEN) 00000000bd703000 - 00000000bd826000 (reserved)
(XEN) 00000000bd826000 - 00000000bd83a000 (ACPI NVS)
(XEN) 00000000bd83a000 - 00000000bd93c000 (reserved)
(XEN) 00000000bd93c000 - 00000000bd93d000 (ACPI NVS)
(XEN) 00000000bd93d000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd94c000 (ACPI data)
(XEN) 00000000bd94c000 - 00000000bd967000 (ACPI NVS)
(XEN) 00000000bd967000 - 00000000bd986000 (reserved)
(XEN) 00000000bd986000 - 00000000bd98c000 (ACPI NVS)
(XEN) 00000000bd98c000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8087MB (8281932kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD94AE18, 005C (r1 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: FACP BD949D98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD942018, 6818 (r1 INTEL DQ45CB 4F INTL
20051117)
(XEN) ACPI: FACS BD952F40, 0040
(XEN) ACPI: APIC BD949F18, 006C (r2 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: MCFG BD954E18, 003C (r1 INTEL DQ45CB 4F
MSFT 97)
(XEN) ACPI: ASF! BD953D18, 00A0 (r32 INTEL DQ45CB 4F TFSM
F4240)
(XEN) ACPI: SPCR BD954D18, 0050 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: TCPA BD954C98, 0032 (r2 INTEL DQ45CB 4F MSFT
1000013)
(XEN) ACPI: DMAR BD93CC18, 0120 (r1 INTEL DQ45CB 4F
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd952f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:485: Host address width 36
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed91000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed92000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed93000
(XEN) [VT-D]dmar.c:358: found INCLUDE_ALL
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base
= bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter
may be needed.
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.099 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
[-- Attachment #2: dmar.txt --]
[-- Type: text/plain, Size: 6798 bytes --]
DMAR dump utility - reading input file DMAR: ../dmar.bin size: 288
DMA Remapping Reporting Structure
==================================================
Signature: DMAR
Length: 0x00000120
Revision: 0x01
Checksum: 0xdd
OEMID: INTEL
OEM Table ID: DQ45CB
OEM Revision: 0x0000004f
Creator ID: INTL
Creator Revision: 0x00000001
HAW: 0x23
Flags: 0x00
Reserved[10]: 00 00 00 00 00 00 00 00 00 00
Remapping Structures...
DMA Remapping Hardware Unit Definition (DRHD) Structure #1
Type: 0x0000 (ACPI_DMAR_DRHD)
Length: 0x0018
Flags: 0x00 -- INCLUDE_ALL = no
Reserved: 0x00
Segment Number: 0x0000
Register Base: 0xfed90000
Device Scope Structure #1
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1b Function: 0x00
DMA Remapping Hardware Unit Definition (DRHD) Structure #2
Type: 0x0000 (ACPI_DMAR_DRHD)
Length: 0x0020
Flags: 0x00 -- INCLUDE_ALL = no
Reserved: 0x00
Segment Number: 0x0000
Register Base: 0xfed91000
Device Scope Structure #1
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x02 Function: 0x00
Device Scope Structure #2
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x02 Function: 0x01
DMA Remapping Hardware Unit Definition (DRHD) Structure #3
Type: 0x0000 (ACPI_DMAR_DRHD)
Length: 0x0028
Flags: 0x00 -- INCLUDE_ALL = no
Reserved: 0x00
Segment Number: 0x0000
Register Base: 0xfed92000
Device Scope Structure #1
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x03 Function: 0x00
Device Scope Structure #2
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x03 Function: 0x02
Device Scope Structure #3
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x03 Function: 0x03
DMA Remapping Hardware Unit Definition (DRHD) Structure #4
Type: 0x0000 (ACPI_DMAR_DRHD)
Length: 0x0010
Flags: 0x01 -- INCLUDE_ALL = yes
Reserved: 0x00
Segment Number: 0x0000
Register Base: 0xfed93000
Reserved Memory Region Reporting (RMRR) Structure #1
Type: 0x0001 (ACPI_DMAR_RMRR)
Length: 0x0058
Reserved: 0x0000
Segment Number: 0x0000
Base Address: 0xbd626000
End Address: 0xbd639fff
Device Scope Structure #1
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1d Function: 0x00
Device Scope Structure #2
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1d Function: 0x01
Device Scope Structure #3
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1d Function: 0x02
Device Scope Structure #4
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1d Function: 0x07
Device Scope Structure #5
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1a Function: 0x00
Device Scope Structure #6
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1a Function: 0x01
Device Scope Structure #7
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1a Function: 0x02
Device Scope Structure #8
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1a Function: 0x07
Reserved Memory Region Reporting (RMRR) Structure #2
Type: 0x0001 (ACPI_DMAR_RMRR)
Length: 0x0028
Reserved: 0x0000
Segment Number: 0x0000
Base Address: 0xbdc00000
End Address: 0xffffffffbfffffff
Device Scope Structure #1
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x02 Function: 0x00
Device Scope Structure #2
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x02 Function: 0x01
==================================================
End DMAR
[-- Attachment #3: lspci.txt --]
[-- Type: text/plain, Size: 19312 bytes --]
00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
00:03.0 Communication controller: Intel Corporation 4 Series Chipset HECI Controller (rev 03)
00:03.2 IDE interface: Intel Corporation 4 Series Chipset PT IDER Controller (rev 03)
00:03.3 Serial controller: Intel Corporation 4 Series Chipset Serial KT Controller (rev 03)
00:19.0 Ethernet controller: Intel Corporation 82567LM-3 Gigabit Network Connection (rev 02)
00:1a.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #4 (rev 02)
00:1a.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #5 (rev 02)
00:1a.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #6 (rev 02)
00:1a.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation ICH10 HD Audio Controller (rev 02)
00:1d.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a2)
00:1f.0 ISA bridge: Intel Corporation ICH10 LPC Interface Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation ICH10 6 port SATA AHCI Controller (rev 02)
00:1f.3 SMBus: Intel Corporation ICH10 SMBus Controller (rev 02)
00:1f.5 IDE interface: Intel Corporation ICH10 2 port SATA IDE Controller (rev 02)
01:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
01:01.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 70)
automatix:~# lspci -vv
00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03)
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at e220 [size=8]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at d0400000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:03.0 Communication controller: Intel Corporation 4 Series Chipset HECI Controller (rev 03)
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0627100 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:03.2 IDE interface: Intel Corporation 4 Series Chipset PT IDER Controller (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at e210 [size=8]
Region 1: I/O ports at e200 [size=4]
Region 2: I/O ports at e1f0 [size=8]
Region 3: I/O ports at e1e0 [size=4]
Region 4: I/O ports at e1d0 [size=16]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:03.3 Serial controller: Intel Corporation 4 Series Chipset Serial KT Controller (rev 03) (prog-if 02 [16550])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 3
Region 0: I/O ports at e1c0 [size=8]
Region 1: Memory at d0625000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:19.0 Ethernet controller: Intel Corporation 82567LM-3 Gigabit Network Connection (rev 02)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 255
Region 0: Memory at d0600000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at d0624000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at e100 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+
Address: 00000000fee0100c Data: 41c0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: e1000e
00:1a.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at e0e0 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #5 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at e0c0 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #6 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at e0a0 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1a.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller
#2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 0: Memory at d0626c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] Vendor Specific Information <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1b.0 Audio device: Intel Corporation ICH10 HD Audio Controller (rev
02)
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d0620000 (64-bit, non-prefetchable) [disabled] [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0
<64ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive-
BWMgmt- ABWMgmt-
Kernel modules: snd-hda-intel
00:1d.0 USB Controller: Intel Corporation ICH10 USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at e080 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller: Intel Corporation ICH10 USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at e060 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller: Intel Corporation ICH10 USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at e040 [size=32]
Capabilities: [50] Vendor Specific Information <?>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller: Intel Corporation ICH10 USB2 EHCI Controller
#1 (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0626800 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] Vendor Specific Information <?>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a2) (prog- if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: d0500000-d05fffff
Prefetchable memory behind bridge: 00000000d0700000-00000000d07fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Gammagraphx, Inc. Device 0000
00:1f.0 ISA bridge: Intel Corporation ICH10 LPC Interface Controller (rev 02)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
00:1f.2 SATA controller: Intel Corporation ICH10 6 port SATA AHCI Controller (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 254
Region 0: I/O ports at e1b0 [size=8]
Region 1: I/O ports at e1a0 [size=4]
Region 2: I/O ports at e190 [size=8]
Region 3: I/O ports at e180 [size=4]
Region 4: I/O ports at e020 [size=32]
Region 5: Memory at d0626000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/3 Enable+
Address: fee0100c Data: 4139
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot
+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA <?>
Capabilities: [b0] Vendor Specific Information <?>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus: Intel Corporation ICH10 SMBus Controller (rev 02)
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at d0627000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at e000 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00:1f.5 IDE interface: Intel Corporation ICH10 2 port SATA IDE Controller (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Intel Corporation Device 1003
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at e170 [size=8]
Region 1: I/O ports at e160 [size=4]
Region 2: I/O ports at e150 [size=8]
Region 3: I/O ports at e140 [size=4]
Region 4: I/O ports at e130 [size=16]
Region 5: I/O ports at e120 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] Vendor Specific Information <?>
Kernel driver in use: ata_piix
Kernel modules: ata_piix
01:00.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at d000 [size=128]
Region 1: Memory at d0521100 (32-bit, non-prefetchable) [size=128]
Expansion ROM at d0700000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: 3c59x
Kernel modules: 3c59x
01:01.0 FireWire (IEEE 1394): Agere Systems FW323 (rev 70) (prog-if 10
[OHCI])
Subsystem: Intel Corporation Device 1003
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d0520000 (32-bit, non-prefetchable) [size=4K]
Region 1: Memory at d0521000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot
+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
[-- Attachment #4: notes.txt --]
[-- Type: text/plain, Size: 4939 bytes --]
** The RMRRs, one for USB and one for GFX
Reserved Memory Region Reporting (RMRR) Structure #1
Type: 0x0001 (ACPI_DMAR_RMRR)
Length: 0x0058
Reserved: 0x0000
Segment Number: 0x0000
Base Address: 0xbd626000
End Address: 0xbd639fff
Device Scope Structure #1
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1d Function: 0x00
Device Scope Structure #2
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1d Function: 0x01
Device Scope Structure #3
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1d Function: 0x02
Device Scope Structure #4
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1d Function: 0x07
Device Scope Structure #5
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1a Function: 0x00
Device Scope Structure #6
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1a Function: 0x01
Device Scope Structure #7
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1a Function: 0x02
Device Scope Structure #8
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x1a Function: 0x07
Reserved Memory Region Reporting (RMRR) Structure #2
Type: 0x0001 (ACPI_DMAR_RMRR)
Length: 0x0028
Reserved: 0x0000
Segment Number: 0x0000
Base Address: 0xbdc00000
End Address: 0xffffffffbfffffff
Device Scope Structure #1
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x02 Function: 0x00
Device Scope Structure #2
==========================
Type: 0x01 (ACPI_DEV_ENDPOINT)
Length: 0x08
Reserved: 00 00
Enumeration ID: 0x00 - Reserved
Start Bus Num: 0x00
Path Depth = 1, Path Entries:
-- Device: 0x02 Function: 0x01
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6c1000 (usable)
(XEN) 00000000bd6c1000 - 00000000bd703000 (ACPI NVS)
(XEN) 00000000bd703000 - 00000000bd826000 (reserved)
(XEN) 00000000bd826000 - 00000000bd83a000 (ACPI NVS)
(XEN) 00000000bd83a000 - 00000000bd93c000 (reserved)
(XEN) 00000000bd93c000 - 00000000bd93d000 (ACPI NVS)
(XEN) 00000000bd93d000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd94c000 (ACPI data)
(XEN) 00000000bd94c000 - 00000000bd967000 (ACPI NVS)
(XEN) 00000000bd967000 - 00000000bd986000 (reserved)
(XEN) 00000000bd986000 - 00000000bd98c000 (ACPI NVS)
(XEN) 00000000bd98c000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
** RMRR 0xbd626000 - 0xbd639fff for USB falls in this e820 range. It should be reserved but is
in a usable range. Not really correct.
(XEN) 0000000000100000 - 00000000bd6c1000 (usable)
** RMRR 0xbdc00000 - 0xffffffffbfffffff for GFX seems way off. It starts in this range but just
keeps going and going.
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
[-- Attachment #5: xen.txt --]
[-- Type: text/plain, Size: 8420 bytes --]
root@obelix:~# amtterm -u admin -p ****** 10.11.1.31
amtterm: NONE -> CONNECT (connection to host)
ipv4 10.11.1.31 [10.11.1.31] 16994 open
amtterm: CONNECT -> INIT (redirection initialization)
amtterm: INIT -> AUTH (session authentication)
amtterm: AUTH -> INIT_SOL (serial-over-lan initialization)
amtterm: INIT_SOL -> RUN_SOL (serial-over-lan active) serial-over-lan redirection ok connected now, use ^] to escape
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ '_ \ |_ \| || |_| | | |__| '__/ __| |_ \ __| '_ \|
'__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@taquiri.dyndns.org) (gcc version
4.3.2 (Debian 4.3.2-1.1) ) Sun Apr 26 16:00:39 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6c1000 (usable)
(XEN) 00000000bd6c1000 - 00000000bd703000 (ACPI NVS)
(XEN) 00000000bd703000 - 00000000bd826000 (reserved)
(XEN) 00000000bd826000 - 00000000bd83a000 (ACPI NVS)
(XEN) 00000000bd83a000 - 00000000bd93c000 (reserved)
(XEN) 00000000bd93c000 - 00000000bd93d000 (ACPI NVS)
(XEN) 00000000bd93d000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd94c000 (ACPI data)
(XEN) 00000000bd94c000 - 00000000bd967000 (ACPI NVS)
(XEN) 00000000bd967000 - 00000000bd986000 (reserved)
(XEN) 00000000bd986000 - 00000000bd98c000 (ACPI NVS)
(XEN) 00000000bd98c000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8087MB (8281932kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD94AE18, 005C (r1 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: FACP BD949D98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD942018, 6818 (r1 INTEL DQ45CB 4F INTL
20051117)
(XEN) ACPI: FACS BD952F40, 0040
(XEN) ACPI: APIC BD949F18, 006C (r2 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: MCFG BD954E18, 003C (r1 INTEL DQ45CB 4F
MSFT 97)
(XEN) ACPI: ASF! BD953D18, 00A0 (r32 INTEL DQ45CB 4F TFSM
F4240)
(XEN) ACPI: SPCR BD954D18, 0050 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: TCPA BD954C98, 0032 (r2 INTEL DQ45CB 4F MSFT
1000013)
(XEN) ACPI: DMAR BD93CC18, 0120 (r1 INTEL DQ45CB 4F
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd952f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:485: Host address width 36
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed91000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed92000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed93000
(XEN) [VT-D]dmar.c:358: found INCLUDE_ALL
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base = bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter may be needed.
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.099 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
[-- Attachment #6: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-28 17:56 ` Ross Philipson
@ 2009-04-29 23:47 ` Tim Kaufmann
2009-04-30 1:00 ` Tim Kaufmann
2009-04-30 4:38 ` Cui, Dexuan
0 siblings, 2 replies; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-29 23:47 UTC (permalink / raw)
To: Ross Philipson; +Cc: xen-devel
Am 28.04.2009 um 19:56 schrieb Ross Philipson:
> Attached is a textual version of your DMAR and some notes. In
> notes.txt at the bottom I noted that both RMRRs seem to have some
> issues but the iommu_inclusive_mapping=1 should have handled them.
I tried again with no success, logfile attached.
> You said the BIOS you have is the latest - did you check with Intel
> to see if there are any known issues?
No, I wouldn't know where to ask. The support pages for the
motherboard show nothing. I tried to downgrade to an earlier BIOS
which was said to be ok here:
http://lists.xensource.com/archives/html/xen-users/2008-10/msg00618.html
Unfortunately the flash tool didn't flash the older BIOS.
Tim
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ '_ \ |_ \| || |_| | | |__| '__/ __| |_ \ __| '_ \|
'__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@taquiri.dyndns.org) (gcc version
4.3.2 (Debian 4.3.2-1.1) ) Sun Apr 26 16:00:39 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
iommu_inclusive_mapping=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6c1000 (usable)
(XEN) 00000000bd6c1000 - 00000000bd703000 (ACPI NVS)
(XEN) 00000000bd703000 - 00000000bd826000 (reserved)
(XEN) 00000000bd826000 - 00000000bd83a000 (ACPI NVS)
(XEN) 00000000bd83a000 - 00000000bd93c000 (reserved)
(XEN) 00000000bd93c000 - 00000000bd93d000 (ACPI NVS)
(XEN) 00000000bd93d000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd94c000 (ACPI data)
(XEN) 00000000bd94c000 - 00000000bd967000 (ACPI NVS)
(XEN) 00000000bd967000 - 00000000bd986000 (reserved)
(XEN) 00000000bd986000 - 00000000bd98c000 (ACPI NVS)
(XEN) 00000000bd98c000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8087MB (8281932kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD94AE18, 005C (r1 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: FACP BD949D98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD942018, 6818 (r1 INTEL DQ45CB 4F INTL
20051117)
(XEN) ACPI: FACS BD952F40, 0040
(XEN) ACPI: APIC BD949F18, 006C (r2 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: MCFG BD954E18, 003C (r1 INTEL DQ45CB 4F
MSFT 97)
(XEN) ACPI: ASF! BD953D18, 00A0 (r32 INTEL DQ45CB 4F TFSM
F4240)
(XEN) ACPI: SPCR BD954D18, 0050 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: TCPA BD954C98, 0032 (r2 INTEL DQ45CB 4F MSFT
1000013)
(XEN) ACPI: DMAR BD93CC18, 0120 (r1 INTEL DQ45CB 4F
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd952f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:485: Host address width 36
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed91000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed92000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed93000
(XEN) [VT-D]dmar.c:358: found INCLUDE_ALL
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base
= bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter
may be needed.
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.069 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-29 23:47 ` Tim Kaufmann
@ 2009-04-30 1:00 ` Tim Kaufmann
2009-04-30 4:38 ` Cui, Dexuan
1 sibling, 0 replies; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-30 1:00 UTC (permalink / raw)
To: xen-devel; +Cc: Ross Philipson
> No, I wouldn't know where to ask. The support pages for the
> motherboard show nothing. I tried to downgrade to an earlier BIOS
> which was said to be ok here:
>
> http://lists.xensource.com/archives/html/xen-users/2008-10/msg00618.html
>
> Unfortunately the flash tool didn't flash the older BIOS.
Ok, I managed to downgrade using the board's BIOS recovery feature.
But even with that BIOS I cannot get a VT-d enabled Xen to boot.
Tim
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ '_ \ |_ \| || |_| | | |__| '__/ __| |_ \ __| '_ \|
'__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@taquiri.dyndns.org) (gcc version
4.3.2 (Debian 4.3.2-1.1) ) Sun Apr 26 16:00:39 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
max_loop=128 dom0_mem=1024M noreboot
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6df000 (usable)
(XEN) 00000000bd6df000 - 00000000bd721000 (ACPI NVS)
(XEN) 00000000bd721000 - 00000000bd83f000 (reserved)
(XEN) 00000000bd83f000 - 00000000bd842000 (ACPI NVS)
(XEN) 00000000bd842000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd943000 (ACPI NVS)
(XEN) 00000000bd943000 - 00000000bd948000 (reserved)
(XEN) 00000000bd948000 - 00000000bd950000 (ACPI data)
(XEN) 00000000bd950000 - 00000000bd96b000 (ACPI NVS)
(XEN) 00000000bd96b000 - 00000000bd98a000 (reserved)
(XEN) 00000000bd98a000 - 00000000bd990000 (ACPI NVS)
(XEN) 00000000bd990000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8087MB (8282036kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD94EE18, 005C (r1 INTEL DQ45CB 3D MSFT
10013)
(XEN) ACPI: FACP BD94DD98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD948018, 4E9A (r1 INTEL DQ45CB 3D INTL
20051117)
(XEN) ACPI: FACS BD956F40, 0040
(XEN) ACPI: APIC BD94DF18, 006C (r2 INTEL DQ45CB 3D MSFT
10013)
(XEN) ACPI: MCFG BD958E18, 003C (r1 INTEL DQ45CB 3D
MSFT 97)
(XEN) ACPI: ASF! BD957D18, 00A0 (r32 INTEL DQ45CB 3D TFSM
F4240)
(XEN) ACPI: SPCR BD958D18, 0050 (r1 INTEL DQ45CB 3D
AMI. 3)
(XEN) ACPI: TCPA BD958C98, 0032 (r2 INTEL DQ45CB 3D MSFT
1000013)
(XEN) ACPI: DMAR BD942C18, 0120 (r1 INTEL DQ45CB 3D
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd956f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:485: Host address width 36
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed91000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed92000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed93000
(XEN) [VT-D]dmar.c:358: found INCLUDE_ALL
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base
= bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter
may be needed.
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.128 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-29 23:47 ` Tim Kaufmann
2009-04-30 1:00 ` Tim Kaufmann
@ 2009-04-30 4:38 ` Cui, Dexuan
2009-04-30 10:44 ` Tim Kaufmann
2009-04-30 11:49 ` Tim Kaufmann
1 sibling, 2 replies; 28+ messages in thread
From: Cui, Dexuan @ 2009-04-30 4:38 UTC (permalink / raw)
To: Tim Kaufmann, Ross Philipson; +Cc: xen-devel
[-- Attachment #1: Type: text/plain, Size: 9785 bytes --]
Hi Tim,
DQ45CB should be Eaglelake/ICH10 based vPro McCreary platform.
Our McCreary test boxes can work fine with VT-d enabled and we don't meet with the hang you see.
You said your McCreary is a custom assembly; not sure what HW/BIOS differences cause your issue.
Can you apply the attached patch to the latest xen-unstable and build xen and try it again? And please post the serial log.
Per my experience, such issues generally are caused by not mapping some pages into VT-d page tables somehow. So let's try the attached patch.
Thanks,
-- Dexuan
-----Original Message-----
From: xen-devel-bounces@lists.xensource.com [mailto:xen-devel-bounces@lists.xensource.com] On Behalf Of Tim Kaufmann
Sent: Thursday, April 30, 2009 7:48 AM
To: Ross Philipson
Cc: xen-devel
Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
Am 28.04.2009 um 19:56 schrieb Ross Philipson:
> Attached is a textual version of your DMAR and some notes. In
> notes.txt at the bottom I noted that both RMRRs seem to have some
> issues but the iommu_inclusive_mapping=1 should have handled them.
I tried again with no success, logfile attached.
> You said the BIOS you have is the latest - did you check with Intel
> to see if there are any known issues?
No, I wouldn't know where to ask. The support pages for the
motherboard show nothing. I tried to downgrade to an earlier BIOS
which was said to be ok here:
http://lists.xensource.com/archives/html/xen-users/2008-10/msg00618.html
Unfortunately the flash tool didn't flash the older BIOS.
Tim
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ '_ \ |_ \| || |_| | | |__| '__/ __| |_ \ __| '_ \|
'__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@taquiri.dyndns.org) (gcc version
4.3.2 (Debian 4.3.2-1.1) ) Sun Apr 26 16:00:39 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
iommu_inclusive_mapping=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6c1000 (usable)
(XEN) 00000000bd6c1000 - 00000000bd703000 (ACPI NVS)
(XEN) 00000000bd703000 - 00000000bd826000 (reserved)
(XEN) 00000000bd826000 - 00000000bd83a000 (ACPI NVS)
(XEN) 00000000bd83a000 - 00000000bd93c000 (reserved)
(XEN) 00000000bd93c000 - 00000000bd93d000 (ACPI NVS)
(XEN) 00000000bd93d000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd94c000 (ACPI data)
(XEN) 00000000bd94c000 - 00000000bd967000 (ACPI NVS)
(XEN) 00000000bd967000 - 00000000bd986000 (reserved)
(XEN) 00000000bd986000 - 00000000bd98c000 (ACPI NVS)
(XEN) 00000000bd98c000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8087MB (8281932kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD94AE18, 005C (r1 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: FACP BD949D98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD942018, 6818 (r1 INTEL DQ45CB 4F INTL
20051117)
(XEN) ACPI: FACS BD952F40, 0040
(XEN) ACPI: APIC BD949F18, 006C (r2 INTEL DQ45CB 4F MSFT
10013)
(XEN) ACPI: MCFG BD954E18, 003C (r1 INTEL DQ45CB 4F
MSFT 97)
(XEN) ACPI: ASF! BD953D18, 00A0 (r32 INTEL DQ45CB 4F TFSM
F4240)
(XEN) ACPI: SPCR BD954D18, 0050 (r1 INTEL DQ45CB 4F
AMI. 3)
(XEN) ACPI: TCPA BD954C98, 0032 (r2 INTEL DQ45CB 4F MSFT
1000013)
(XEN) ACPI: DMAR BD93CC18, 0120 (r1 INTEL DQ45CB 4F
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd952f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:485: Host address width 36
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed91000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed92000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed93000
(XEN) [VT-D]dmar.c:358: found INCLUDE_ALL
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base
= bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter
may be needed.
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.069 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
[-- Attachment #2: map_all.patch --]
[-- Type: application/octet-stream, Size: 1303 bytes --]
diff -r cc6db34c2996 xen/drivers/passthrough/iommu.c
--- a/xen/drivers/passthrough/iommu.c Wed Apr 29 13:54:57 2009 +0100
+++ b/xen/drivers/passthrough/iommu.c Thu Apr 30 12:19:01 2009 +0800
@@ -51,9 +51,9 @@ static void __init parse_iommu_param(cha
{
char *ss;
iommu_enabled = 1;
- iommu_snoop = 1;
- iommu_qinval = 1;
- iommu_intremap = 1;
+ iommu_snoop = 0;
+ iommu_qinval = 0;
+ iommu_intremap = 0;
do {
ss = strchr(s, ',');
diff -r cc6db34c2996 xen/drivers/passthrough/vtd/x86/vtd.c
--- a/xen/drivers/passthrough/vtd/x86/vtd.c Wed Apr 29 13:54:57 2009 +0100
+++ b/xen/drivers/passthrough/vtd/x86/vtd.c Thu Apr 30 12:20:37 2009 +0800
@@ -168,6 +168,7 @@ void iommu_set_dom0_mapping(struct domai
* inclusive mapping maps in everything below 4GB except unusable
* ranges.
*/
+#if 0
if ( !page_is_ram_type(i, RAM_TYPE_CONVENTIONAL) &&
(!iommu_inclusive_mapping ||
page_is_ram_type(i, RAM_TYPE_UNUSABLE)) )
@@ -176,6 +177,7 @@ void iommu_set_dom0_mapping(struct domai
/* Exclude Xen bits */
if ( xen_in_range(i << PAGE_SHIFT, (i + 1) << PAGE_SHIFT) )
continue;
+#endif
tmp = 1 << (PAGE_SHIFT - PAGE_SHIFT_4K);
for ( j = 0; j < tmp; j++ )
[-- Attachment #3: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-30 4:38 ` Cui, Dexuan
@ 2009-04-30 10:44 ` Tim Kaufmann
2009-04-30 11:49 ` Tim Kaufmann
1 sibling, 0 replies; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-30 10:44 UTC (permalink / raw)
To: Cui, Dexuan; +Cc: xen-devel, Ross Philipson
Hi Dexuan,
> You said your McCreary is a custom assembly; not sure what HW/BIOS
> differences cause your issue.
May be there's a misunderstanding. I bought a boxed motherboard and
cpu, a case and a psu and had them assembled by a local computer
company. And I downloaded the official BIOS from intel.com.
> Can you apply the attached patch to the latest xen-unstable and
> build xen and try it again?
Like this?
cd /usr/src/xen-unstable
patch -p1 < ../map.all.patch
Tim
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-30 4:38 ` Cui, Dexuan
2009-04-30 10:44 ` Tim Kaufmann
@ 2009-04-30 11:49 ` Tim Kaufmann
2009-05-04 21:48 ` Tim Kaufmann
2009-05-05 7:57 ` Cui, Dexuan
1 sibling, 2 replies; 28+ messages in thread
From: Tim Kaufmann @ 2009-04-30 11:49 UTC (permalink / raw)
To: Cui, Dexuan; +Cc: xen-devel
Am 30.04.2009 um 06:38 schrieb Cui, Dexuan:
> So let's try the attached patch.
Couldn't wait, so I patched with
$ patch -p1 < ../map.all.patch
Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
Output below.
Tim
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ '_ \ |_ \| || |_| | | |__| '__/ __| |_ \ __| '_ \|
'__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@taquiri.dyndns.org) (gcc version
4.3.2 (Debian 4.3.2-1.1) ) Thu Apr 30 13:21:56 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6df000 (usable)
(XEN) 00000000bd6df000 - 00000000bd721000 (ACPI NVS)
(XEN) 00000000bd721000 - 00000000bd83f000 (reserved)
(XEN) 00000000bd83f000 - 00000000bd842000 (ACPI NVS)
(XEN) 00000000bd842000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd943000 (ACPI NVS)
(XEN) 00000000bd943000 - 00000000bd948000 (reserved)
(XEN) 00000000bd948000 - 00000000bd950000 (ACPI data)
(XEN) 00000000bd950000 - 00000000bd96b000 (ACPI NVS)
(XEN) 00000000bd96b000 - 00000000bd98a000 (reserved)
(XEN) 00000000bd98a000 - 00000000bd990000 (ACPI NVS)
(XEN) 00000000bd990000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8087MB (8282036kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD94EE18, 005C (r1 INTEL DQ45CB 3D MSFT
10013)
(XEN) ACPI: FACP BD94DD98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD948018, 4E9A (r1 INTEL DQ45CB 3D INTL
20051117)
(XEN) ACPI: FACS BD956F40, 0040
(XEN) ACPI: APIC BD94DF18, 006C (r2 INTEL DQ45CB 3D MSFT
10013)
(XEN) ACPI: MCFG BD958E18, 003C (r1 INTEL DQ45CB 3D
MSFT 97)
(XEN) ACPI: ASF! BD957D18, 00A0 (r32 INTEL DQ45CB 3D TFSM
F4240)
(XEN) ACPI: SPCR BD958D18, 0050 (r1 INTEL DQ45CB 3D
AMI. 3)
(XEN) ACPI: TCPA BD958C98, 0032 (r2 INTEL DQ45CB 3D MSFT
1000013)
(XEN) ACPI: DMAR BD942C18, 0120 (r1 INTEL DQ45CB 3D
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd956f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:485: Host address width 36
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed91000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed92000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed93000
(XEN) [VT-D]dmar.c:358: found INCLUDE_ALL
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base
= bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter
may be needed.
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.079 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-30 11:49 ` Tim Kaufmann
@ 2009-05-04 21:48 ` Tim Kaufmann
2009-05-05 7:41 ` Re[2]: " Sander Eikelenboom
2009-05-20 19:38 ` Sander Eikelenboom
2009-05-05 7:57 ` Cui, Dexuan
1 sibling, 2 replies; 28+ messages in thread
From: Tim Kaufmann @ 2009-05-04 21:48 UTC (permalink / raw)
To: xen-devel; +Cc: Dexuan Cui
Nobody's got a clue on how to solve this? Should I get myself another
motherboard, and if so, which one is recommended?
Tim
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re[2]: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-05-04 21:48 ` Tim Kaufmann
@ 2009-05-05 7:41 ` Sander Eikelenboom
2009-05-20 19:38 ` Sander Eikelenboom
1 sibling, 0 replies; 28+ messages in thread
From: Sander Eikelenboom @ 2009-05-05 7:41 UTC (permalink / raw)
To: Tim Kaufmann; +Cc: xen-devel
There are also VT-D troubles on ASUS motherboards, perhaps it's even AMI-bios
related. I'm having support requests running at both at the moment. I will
keep the list informed if it's solved (or not)
I was considering the DQ45CB if those support calls don't result in a fix,
but from what I hear from you even Intel isn't able to make it work out of
the box too :-(. And i'm not going to buy something again without knowing
sure it does what it promises and has error-free VT-D/IOMMU support.
I hope it gets straightened out soon, else AMD will release there first
chipset with IOMMU, perhaps they did a better job...
Perhaps it would be wise to make a list on the VT-D passthrough wiki of
motherboards that do or don't have error free VT-D.
--
Sander
Monday, May 4, 2009, 11:48:53 PM, you wrote:
> Nobody's got a clue on how to solve this? Should I get myself another
> motherboard, and if so, which one is recommended?
> Tim
--
Best regards,
Sander mailto:linux@eikelenboom.it
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-04-30 11:49 ` Tim Kaufmann
2009-05-04 21:48 ` Tim Kaufmann
@ 2009-05-05 7:57 ` Cui, Dexuan
1 sibling, 0 replies; 28+ messages in thread
From: Cui, Dexuan @ 2009-05-05 7:57 UTC (permalink / raw)
To: Tim Kaufmann; +Cc: xen-devel
Since you still meet with the hang even with all MFNs mapped, I have no idea now. :-(
Could you please try the latest native Linux kernel with IOMMU on?
If native Linux has the same symptom, I personally tend to think this is a BIOS issue.
Thanks,
-- Dexuan
-----Original Message-----
From: Tim Kaufmann [mailto:tk@taquiri.de]
Sent: 2009年4月30日 19:49
To: Cui, Dexuan
Cc: xen-devel
Subject: Re: [Xen-devel] No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
Am 30.04.2009 um 06:38 schrieb Cui, Dexuan:
> So let's try the attached patch.
Couldn't wait, so I patched with
$ patch -p1 < ../map.all.patch
Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
Output below.
Tim
__ __ _____ _ _ ___ _____
\ \/ /___ _ __ |___ /| || | / _ \ _ __ ___|___ / _ __ _ __
___
\ // _ \ '_ \ |_ \| || |_| | | |__| '__/ __| |_ \ __| '_ \|
'__/ _ \
/ \ __/ | | | ___) |__ _| |_| |__| | | (__ ___) |__| |_) | |
| __/
/_/\_\___|_| |_| |____(_) |_|(_)___/ |_| \___|____/ | .__/|_|
\___|
|_|
(XEN) Xen version 3.4.0-rc3-pre (root@taquiri.dyndns.org) (gcc version
4.3.2 (Debian 4.3.2-1.1) ) Thu Apr 30 13:21:56 CEST 2009
(XEN) Latest ChangeSet: Fri Apr 24 13:46:17 2009 +0100
19575:dc5bd14a4675
(XEN) Command line: console=com1 com1=115200,8n1,0xe1c0,0 iommu=1
(XEN) Video information:
(XEN) VGA is text mode 80x25, font 8x16
(XEN) VBE/DDC methods: none; EDID transfer time: 0 seconds
(XEN) EDID info not retrieved because no DDC retrieval method detected
(XEN) Disc information:
(XEN) Found 0 MBR signatures
(XEN) Found 5 EDD information structures
(XEN) Xen-e820 RAM map:
(XEN) 0000000000000000 - 000000000009e800 (usable)
(XEN) 000000000009e800 - 00000000000a0000 (reserved)
(XEN) 00000000000e0000 - 0000000000100000 (reserved)
(XEN) 0000000000100000 - 00000000bd6df000 (usable)
(XEN) 00000000bd6df000 - 00000000bd721000 (ACPI NVS)
(XEN) 00000000bd721000 - 00000000bd83f000 (reserved)
(XEN) 00000000bd83f000 - 00000000bd842000 (ACPI NVS)
(XEN) 00000000bd842000 - 00000000bd942000 (reserved)
(XEN) 00000000bd942000 - 00000000bd943000 (ACPI NVS)
(XEN) 00000000bd943000 - 00000000bd948000 (reserved)
(XEN) 00000000bd948000 - 00000000bd950000 (ACPI data)
(XEN) 00000000bd950000 - 00000000bd96b000 (ACPI NVS)
(XEN) 00000000bd96b000 - 00000000bd98a000 (reserved)
(XEN) 00000000bd98a000 - 00000000bd990000 (ACPI NVS)
(XEN) 00000000bd990000 - 00000000bdb00000 (usable)
(XEN) 00000000bdc00000 - 00000000c0000000 (reserved)
(XEN) 00000000fed1c000 - 00000000fed20000 (reserved)
(XEN) 00000000ff000000 - 0000000100000000 (reserved)
(XEN) 0000000100000000 - 000000023c000000 (usable)
(XEN) System RAM: 8087MB (8282036kB)
(XEN) ACPI: RSDP 000F03C0, 0024 (r2 INTEL)
(XEN) ACPI: XSDT BD94EE18, 005C (r1 INTEL DQ45CB 3D MSFT
10013)
(XEN) ACPI: FACP BD94DD98, 00F4 (r4 INTEL A M I 6222004 MSFT
10013)
(XEN) ACPI: DSDT BD948018, 4E9A (r1 INTEL DQ45CB 3D INTL
20051117)
(XEN) ACPI: FACS BD956F40, 0040
(XEN) ACPI: APIC BD94DF18, 006C (r2 INTEL DQ45CB 3D MSFT
10013)
(XEN) ACPI: MCFG BD958E18, 003C (r1 INTEL DQ45CB 3D
MSFT 97)
(XEN) ACPI: ASF! BD957D18, 00A0 (r32 INTEL DQ45CB 3D TFSM
F4240)
(XEN) ACPI: SPCR BD958D18, 0050 (r1 INTEL DQ45CB 3D
AMI. 3)
(XEN) ACPI: TCPA BD958C98, 0032 (r2 INTEL DQ45CB 3D MSFT
1000013)
(XEN) ACPI: DMAR BD942C18, 0120 (r1 INTEL DQ45CB 3D
INTL 1)
(XEN) NUMA turned off
(XEN) Faking a node at 0000000000000000-000000023c000000
(XEN) Domain heap initialised
(XEN) DMI 2.4 present.
(XEN) Using APIC driver default
(XEN) ACPI: PM-Timer IO Port: 0x408
(XEN) ACPI: ACPI SLEEP INFO: pm1x_cnt[404,0], pm1x_evt[400,0]
(XEN) ACPI: wakeup_vec[bd956f4c], vec_size[20]
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
(XEN) Processor #2 7:7 APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
(XEN) Processor #3 7:7 APIC version 20
(XEN) ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
(XEN) IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
(XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
(XEN) ACPI: IRQ0 used by override.
(XEN) ACPI: IRQ2 used by override.
(XEN) ACPI: IRQ9 used by override.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) [VT-D]dmar.c:485: Host address width 36
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed90000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1b.0
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed91000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed92000
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:3.3
(XEN) [VT-D]dmar.c:494: found ACPI_DMAR_DRHD
(XEN) [VT-D]dmar.c:349: dmaru->address = fed93000
(XEN) [VT-D]dmar.c:358: found INCLUDE_ALL
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1d.7
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.1
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.2
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:1a.7
(XEN) [VT-D]dmar.c:498: found ACPI_DMAR_RMRR
(XEN) [VT-D]dmar.c:401: RMRR address range not in reserved memory base
= bdc00000 end = ffffffffbfffffff; iommu_inclusive_mapping=1 parameter
may be needed.
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.0
(XEN) [VT-D]dmar.c:300: found endpoint: bdf = 0:2.1
(XEN) Intel VT-d DMAR tables have been parsed.
(XEN) Using ACPI (MADT) for SMP configuration information
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Initializing CPU#0
(XEN) Detected 2833.079 MHz processor.
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 0
(XEN) VMX: Supported advanced features:
(XEN) - APIC MMIO access virtualisation
(XEN) - APIC TPR shadow
(XEN) - Virtual NMI
(XEN) - MSR direct-access bitmap
(XEN) HVM: VMX enabled
(XEN) Intel machine check reporting enabled on CPU#0.
(XEN) CPU0: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU0 has no CMCI support
(XEN) CPU0: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 1/1 eip 8c000
(XEN) Initializing CPU#1
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 1
(XEN) Intel machine check reporting enabled on CPU#1.
(XEN) CPU1: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU1 has no CMCI support
(XEN) CPU1: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 2/2 eip 8c000
(XEN) Initializing CPU#2
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 2
(XEN) Intel machine check reporting enabled on CPU#2.
(XEN) CPU2: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU2 has no CMCI support
(XEN) CPU2: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Booting processor 3/3 eip 8c000
(XEN) Initializing CPU#3
(XEN) CPU: L1 I cache: 32K, L1 D cache: 32K
(XEN) CPU: L2 cache: 6144K
(XEN) CPU: Physical Processor ID: 0
(XEN) CPU: Processor Core ID: 3
(XEN) Intel machine check reporting enabled on CPU#3.
(XEN) CPU3: Thermal monitoring enabled (TM2)
(XEN) CMCI: CPU3 has no CMCI support
(XEN) CPU3: Intel(R) Core(TM)2 Quad CPU Q9550 @ 2.83GHz stepping 0a
(XEN) Total of 4 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) -> Using new ACK method
(XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=-1 pin2=-1
(XEN) checking TSC synchronization across 4 CPUs: passed.
(XEN) Platform timer is 3.579MHz ACPI PM Timer
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re[2]: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-05-04 21:48 ` Tim Kaufmann
2009-05-05 7:41 ` Re[2]: " Sander Eikelenboom
@ 2009-05-20 19:38 ` Sander Eikelenboom
2009-05-20 21:33 ` Tim Kaufmann
1 sibling, 1 reply; 28+ messages in thread
From: Sander Eikelenboom @ 2009-05-20 19:38 UTC (permalink / raw)
To: Tim Kaufmann; +Cc: xen-devel
Hello Tim,
Are you problems with VT-D and the Intel-Board DQ45CB fixed ?
Since i'm considering buying this motherboard for VT-D use ...
Regards,
Sander Eikelenboom
Monday, May 4, 2009, 11:48:53 PM, you wrote:
> Nobody's got a clue on how to solve this? Should I get myself another
> motherboard, and if so, which one is recommended?
> Tim
--
Best regards,
Sander mailto:linux@eikelenboom.it
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: Re[2]: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-05-20 19:38 ` Sander Eikelenboom
@ 2009-05-20 21:33 ` Tim Kaufmann
2009-05-22 2:45 ` Cui, Dexuan
0 siblings, 1 reply; 28+ messages in thread
From: Tim Kaufmann @ 2009-05-20 21:33 UTC (permalink / raw)
To: xen-devel
Cc: Anthony Bosio, "Matthias P. Würfl",
Sander Eikelenboom
Am 20.05.2009 um 21:38 schrieb Sander Eikelenboom:
> Are you problems with VT-D and the Intel-Board DQ45CB fixed ?
Almost.
In fact, the hang occurs with RAM > 2 GB and is caused by a BIOS
error. As one of the Intel guys on this list told me after several
tests:
> Please let me offer more technical details about the hang you suffer
> from:
> Due to the very very big and bad rmrr->end_address
> 0xffffffffbfffffff, in setup_dom0_rmrr() ->
> iommu_prepare_rmrr_dev(), intel_iommu_map_page() is invoked too too
> many times and you see the hang...
I already received a patch for Xen 3.4RC4 which I can properly enable
VT-d with. But there'll be a BIOS-Update soon, they promised.
Tim
^ permalink raw reply [flat|nested] 28+ messages in thread
* RE: Re[2]: No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB
2009-05-20 21:33 ` Tim Kaufmann
@ 2009-05-22 2:45 ` Cui, Dexuan
0 siblings, 0 replies; 28+ messages in thread
From: Cui, Dexuan @ 2009-05-22 2:45 UTC (permalink / raw)
To: Tim Kaufmann, xen-devel
Cc: Anthony Bosio, "Matthias P. Würfl", Eikelenboom
Tim Kaufmann wrote:
> Am 20.05.2009 um 21:38 schrieb Sander Eikelenboom:
>
>> Are you problems with VT-D and the Intel-Board DQ45CB fixed ?
>
> Almost.
>
> In fact, the hang occurs with RAM > 2 GB and is caused by a BIOS
> error. As one of the Intel guys on this list told me after several
> tests:
Actually the VT-d support of the motherboard is good.
The issue is caused by a small mistake in RMRR reporting in BIOS.
>
>> Please let me offer more technical details about the hang you suffer
>> from: Due to the very very big and bad rmrr->end_address
>> 0xffffffffbfffffff, in setup_dom0_rmrr() ->
>> iommu_prepare_rmrr_dev(), intel_iommu_map_page() is invoked too too
>> many times and you see the hang...
>
> I already received a patch for Xen 3.4RC4 which I can properly enable
> VT-d with. But there'll be a BIOS-Update soon, they promised.
Yes, I think a BIOS update should come out soon.
For now, we can use the following small patch as a workaround. :-)
diff -r f80cf52a4fb6 xen/drivers/passthrough/vtd/iommu.c
--- a/xen/drivers/passthrough/vtd/iommu.c Thu Apr 30 14:34:15 2009 +0100
+++ b/xen/drivers/passthrough/vtd/iommu.c Mon May 18 16:12:14 2009 +0800
@@ -1541,6 +1541,8 @@ static int iommu_prepare_rmrr_dev(struct
ASSERT(spin_is_locked(&pcidevs_lock));
ASSERT(rmrr->base_address < rmrr->end_address);
+ if ( (rmrr->end_address >> 32) & 0x80000000 )
+ rmrr->end_address &= 0xFFFFFFFF;
base = rmrr->base_address & PAGE_MASK_4K;
base_pfn = base >> PAGE_SHIFT_4K;
end = PAGE_ALIGN_4K(rmrr->end_address);
Thanks,
-- Dexuan
^ permalink raw reply [flat|nested] 28+ messages in thread
end of thread, other threads:[~2009-05-22 2:45 UTC | newest]
Thread overview: 28+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-04-26 14:29 No VT-d with Xen 3.3/3.4rc3 on Intel-Board DQ45CB Tim Kaufmann
2009-04-26 14:51 ` Tim Kaufmann
2009-04-26 21:04 ` Ross Philipson
2009-04-26 23:35 ` Tim Kaufmann
2009-04-27 13:39 ` Ross Philipson
[not found] ` <F126C20F-9063-4FCC-BF8F-FE4CCDBCF1E5@taquiri.de>
[not found] ` <831D55AF5A11D64C9B4B43F59EEBF72035FCB540E5@FTLPMAILBOX02.citrite.net>
[not found] ` <21F81074-ADE6-4913-A77E-4615F84E5CB9@taquiri.de>
[not found] ` <831D55AF5A11D64C9B4B43F59EEBF72035FCB540F1@FTLPMAILBOX02.citrite.net>
2009-04-27 16:48 ` Tim Kaufmann
2009-04-27 18:00 ` Ross Philipson
2009-04-27 18:31 ` Tim Kaufmann
2009-04-27 18:39 ` Ross Philipson
2009-04-27 19:01 ` Pasi Kärkkäinen
2009-04-27 19:07 ` Ross Philipson
2009-04-27 21:15 ` Tim Kaufmann
2009-04-27 21:23 ` Ross Philipson
2009-04-28 17:56 ` Ross Philipson
2009-04-29 23:47 ` Tim Kaufmann
2009-04-30 1:00 ` Tim Kaufmann
2009-04-30 4:38 ` Cui, Dexuan
2009-04-30 10:44 ` Tim Kaufmann
2009-04-30 11:49 ` Tim Kaufmann
2009-05-04 21:48 ` Tim Kaufmann
2009-05-05 7:41 ` Re[2]: " Sander Eikelenboom
2009-05-20 19:38 ` Sander Eikelenboom
2009-05-20 21:33 ` Tim Kaufmann
2009-05-22 2:45 ` Cui, Dexuan
2009-05-05 7:57 ` Cui, Dexuan
2009-04-27 10:41 ` Christian Tramnitz
2009-04-27 11:16 ` Tim Kaufmann
2009-04-27 14:51 ` Christian Tramnitz
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.