* Some updates for GeodeLX based devices
@ 2009-05-13 14:46 Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 1/6] Remove alix machine, update geodelx one to use Alix settings Marcin Juszkiewicz
` (5 more replies)
0 siblings, 6 replies; 17+ messages in thread
From: Marcin Juszkiewicz @ 2009-05-13 14:46 UTC (permalink / raw)
To: openembedded-devel
As recently some useer on Angstrom-devel mailing list asked about state
of GeodeLX based devices in OE I decided to make it more up to date.
Result is this set of patches for review. I did not yet checked build
results on Alix.1c but this is planned for next few days.
[PATCH 1/6] Remove alix machine, update geodelx one to use Alix settings
This patch renames 'alix' machine to 'geodelx' which can be used by
anyone for other GeodeLX based devices.
[PATCH 2/6] kaeilos/sane-feed: remove alix, mark geodelx as i586
Fixed architecture settings for geodelx.
[PATCH 3/6] kaeilos.inc/sane-feed.inc: use spaces instead of tabs
[PATCH 4/6] kaeilos: use include/sane-feed.inc
Patch 2/6 looks strange when 4/6 is applied too but I wanted to make it
clean.
[PATCH 5/6] linux: drop alix, move geodelx to 2.6.29
GeodeLX machine in OE used 2.6.10 kernel which is deprecated in Ångström
(as our udev require at least 2.6.12 (if not .16 even)).
[PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
GCC 4.3.3 has "-march=geode" which is used in tune-geode.inc so I bumped
it for Ångström. This is part of 'upgrade gcc/binutils' plan.
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH 1/6] Remove alix machine, update geodelx one to use Alix settings
2009-05-13 14:46 Some updates for GeodeLX based devices Marcin Juszkiewicz
@ 2009-05-13 14:46 ` Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 2/6] kaeilos/sane-feed: remove alix, mark geodelx as i586 Marcin Juszkiewicz
` (4 subsequent siblings)
5 siblings, 0 replies; 17+ messages in thread
From: Marcin Juszkiewicz @ 2009-05-13 14:46 UTC (permalink / raw)
To: openembedded-devel; +Cc: Marcin Juszkiewicz
From: Marcin Juszkiewicz <hrw@openembedded.org>
Alix.1c is GeodeLX based so no need to keep two machine configs.
And there are people which tries to use geodelx as base for their
devices and get into troubles as it uses quite old kernel.
Signed-off-by: Marcin Juszkiewicz <hrw@openembedded.org>
---
conf/machine/alix.conf | 27 ---------------------------
conf/machine/geodelx.conf | 15 ++++++++++++---
2 files changed, 12 insertions(+), 30 deletions(-)
delete mode 100644 conf/machine/alix.conf
diff --git a/conf/machine/alix.conf b/conf/machine/alix.conf
deleted file mode 100644
index 7b9aa98..0000000
--- a/conf/machine/alix.conf
+++ /dev/null
@@ -1,27 +0,0 @@
-#@TYPE: Machine
-#@NAME: Alix
-#@DESCRIPTION: Machine.inciguration for PC Engines Alix1c board
-#
-# http://pcengines.ch/alix1c.htm
-
-# i386 doesn't work with NTPL, see http://ecos.sourceware.org/ml/libc-ports/2006-03/msg00030.html
-TARGET_ARCH = "i586"
-
-PREFERRED_PROVIDER_virtual/kernel = "linux"
-PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
-
-OLDEST_KERNEL = "2.6.17"
-GLIBC_ADDONS = "nptl"
-GLIBC_EXTRA_OECONF = "--with-tls"
-
-MACHINE_FEATURES = "kernel26 usbhost ext2 pci screen alsa acpi x86"
-
-require conf/machine/include/tune-geodelx.inc
-
-IMAGE_FSTYPES += "tar.gz"
-
-MACHINE_EXTRA_RRECOMMENDS = "\
- kernel-modules \
- "
-
-KERNEL_IMAGETYPE = "bzImage"
diff --git a/conf/machine/geodelx.conf b/conf/machine/geodelx.conf
index de4d9ca..bd87077 100644
--- a/conf/machine/geodelx.conf
+++ b/conf/machine/geodelx.conf
@@ -1,10 +1,15 @@
-TARGET_ARCH = "i486"
+#@TYPE: Machine
+#@NAME: Geode LX
+#@DESCRIPTION: Machine configuration for GeodeLX based devices
+
+TARGET_ARCH = "i586"
require conf/machine/include/tune-geodelx.inc
-PREFERRED_PROVIDERS += " virtual/${TARGET_PREFIX}depmod:module-init-tools-cross"
+PREFERRED_PROVIDER_virtual/kernel = "linux"
+PREFERRED_PROVIDER_virtual/xserver = "xserver-xorg"
-PREFERRED_PROVIDER_virtual/kernel="linux-geodelx"
+MACHINE_FEATURES = "kernel26 usbhost ext2 pci screen alsa acpi x86"
SELECTED_OPTIMIZATION_glibc := "${@'${SELECTED_OPTIMIZATION}'.replace('-fomit-frame-pointer', '')}"
@@ -12,3 +17,7 @@ KERNEL_IMAGETYPE = "bzImage"
GLIBC_ADDONS = "nptl"
GLIBC_EXTRA_OECONF = "--with-tls"
+
+IMAGE_FSTYPES += "tar.gz"
+
+MACHINE_EXTRA_RRECOMMENDS += "kernel-modules"
--
1.6.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 2/6] kaeilos/sane-feed: remove alix, mark geodelx as i586
2009-05-13 14:46 Some updates for GeodeLX based devices Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 1/6] Remove alix machine, update geodelx one to use Alix settings Marcin Juszkiewicz
@ 2009-05-13 14:46 ` Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 3/6] kaeilos.inc/sane-feed.inc: use spaces instead of tabs Marcin Juszkiewicz
` (3 subsequent siblings)
5 siblings, 0 replies; 17+ messages in thread
From: Marcin Juszkiewicz @ 2009-05-13 14:46 UTC (permalink / raw)
To: openembedded-devel; +Cc: Marcin Juszkiewicz
From: Marcin Juszkiewicz <hrw@openembedded.org>
hrw@alix:~$ uname -a
Linux alix 2.6.29-1-686 #1 SMP Sat Apr 4 17:36:29 UTC 2009 i586 GNU/Linux
hrw@alix:~$ cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 5
model : 10
model name : Geode(TM) Integrated Processor by AMD PCS
stepping : 2
cpu MHz : 498.034
cache size : 128 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu de pse tsc msr cx8 sep pge cmov clflush mmx mmxext 3dnowext 3dnow up
bogomips : 996.06
clflush size : 32
power management:
Signed-off-by: Marcin Juszkiewicz <hrw@openembedded.org>
---
conf/distro/include/kaeilos.inc | 3 +--
conf/distro/include/sane-feed.inc | 3 +--
2 files changed, 2 insertions(+), 4 deletions(-)
diff --git a/conf/distro/include/kaeilos.inc b/conf/distro/include/kaeilos.inc
index de7dca7..e7e63d2 100644
--- a/conf/distro/include/kaeilos.inc
+++ b/conf/distro/include/kaeilos.inc
@@ -226,19 +226,18 @@ FEED_ARCH_omap2430sdp = "armv6"
#i486 machines
FEED_ARCH_geodegx = "i486"
-FEED_ARCH_geodelx = "i486"
FEED_ARCH_netvista = "i486"
FEED_ARCH_wrap = "i486"
FEED_ARCH_x86 = "i486"
#i586 machines
FEED_ARCH_epia = "i586"
+FEED_ARCH_geodelx = "i586"
FEED_ARCH_i586-generic = "i586"
FEED_ARCH_qemux86 = "i586"
#i686 machines
-FEED_ARCH_alix = "i686"
FEED_ARCH_colinux = "i686"
FEED_ARCH_guinness = "i686"
FEED_ARCH_i686-generic = "i686"
diff --git a/conf/distro/include/sane-feed.inc b/conf/distro/include/sane-feed.inc
index 5bc19a1..2673f9d 100644
--- a/conf/distro/include/sane-feed.inc
+++ b/conf/distro/include/sane-feed.inc
@@ -116,19 +116,18 @@ FEED_ARCH_omap2430sdp = "armv6"
# i486 machines
FEED_ARCH_geodegx = "i486"
-FEED_ARCH_geodelx = "i486"
FEED_ARCH_netvista = "i486"
FEED_ARCH_wrap = "i486"
FEED_ARCH_x86 = "i486"
# i586 machines
FEED_ARCH_epia = "i586"
+FEED_ARCH_geodelx = "i586"
FEED_ARCH_i586-generic = "i586"
FEED_ARCH_qemux86 = "i586"
# i686 machines
-FEED_ARCH_alix = "i686"
FEED_ARCH_colinux = "i686"
FEED_ARCH_guinness = "i686"
FEED_ARCH_i686-generic = "i686"
--
1.6.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 3/6] kaeilos.inc/sane-feed.inc: use spaces instead of tabs
2009-05-13 14:46 Some updates for GeodeLX based devices Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 1/6] Remove alix machine, update geodelx one to use Alix settings Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 2/6] kaeilos/sane-feed: remove alix, mark geodelx as i586 Marcin Juszkiewicz
@ 2009-05-13 14:46 ` Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 4/6] kaeilos: use include/sane-feed.inc Marcin Juszkiewicz
` (2 subsequent siblings)
5 siblings, 0 replies; 17+ messages in thread
From: Marcin Juszkiewicz @ 2009-05-13 14:46 UTC (permalink / raw)
To: openembedded-devel; +Cc: Marcin Juszkiewicz
From: Marcin Juszkiewicz <hrw@openembedded.org>
Signed-off-by: Marcin Juszkiewicz <hrw@openembedded.org>
---
conf/distro/include/kaeilos.inc | 242 ++++++++++++++++++------------------
conf/distro/include/sane-feed.inc | 226 +++++++++++++++++-----------------
2 files changed, 234 insertions(+), 234 deletions(-)
diff --git a/conf/distro/include/kaeilos.inc b/conf/distro/include/kaeilos.inc
index e7e63d2..d34849f 100644
--- a/conf/distro/include/kaeilos.inc
+++ b/conf/distro/include/kaeilos.inc
@@ -1,9 +1,9 @@
#@TYPE: Distribution
-#@NAME: KaeilOS
-#@DESCRIPTION: Release independent distribution configuration for KaeilOS
+#@NAME: KaeilOS
+#@DESCRIPTION: Release independent distribution configuration for KaeilOS
#@MAINTAINER: Marco Cavallini <m.cavallini@koansoftware.com>
# KaeilOS is a registered trade mark of KOAN - Bergamo - Italia
-# Product website : http://www.KaeilOS.com
+# Product website : http://www.KaeilOS.com
# Preserve original DISTRO value
USERDISTRO := "${DISTRO}"
@@ -70,15 +70,15 @@ MAINTAINER = "KaeilOS Developers <info@koansoftware.com>"
INHERIT += "debian"
#activate config checker
-INHERIT += "sanity"
+INHERIT += "sanity"
#make devshell available as task
-INHERIT += "devshell"
+INHERIT += "devshell"
#use angstrom source mirrors to combat 404s
-INHERIT += "angstrom-mirrors"
+INHERIT += "angstrom-mirrors"
-#run QA tests on builds and packages and log them
+#run QA tests on builds and packages and log them
INHERIT += "insane"
QA_LOG = "1"
@@ -128,148 +128,148 @@ FEED_ARCH_bfin = "blackfin"
#armv4t machines
-FEED_ARCH_acern30 = "armv4t"
-FEED_ARCH_amsdelta = "armv4t"
-FEED_ARCH_ep93xx = "armv4t"
-FEED_ARCH_eteng500 = "armv4t"
-FEED_ARCH_om-gta01 = "armv4t"
-FEED_ARCH_om-gta02 = "armv4t"
-FEED_ARCH_h1940 = "armv4t"
-FEED_ARCH_h6300 = "armv4t"
-FEED_ARCH_kb9202 = "armv4t"
-FEED_ARCH_ks8695 = "armv4t"
-FEED_ARCH_rx1950 = "armv4t"
-FEED_ARCH_rx3000 = "armv4t"
-FEED_ARCH_sarge-at91 = "armv4t"
-FEED_ARCH_smdk2440 = "armv4t"
-FEED_ARCH_smdk2443 = "armv4t"
+FEED_ARCH_acern30 = "armv4t"
+FEED_ARCH_amsdelta = "armv4t"
+FEED_ARCH_ep93xx = "armv4t"
+FEED_ARCH_eteng500 = "armv4t"
+FEED_ARCH_om-gta01 = "armv4t"
+FEED_ARCH_om-gta02 = "armv4t"
+FEED_ARCH_h1940 = "armv4t"
+FEED_ARCH_h6300 = "armv4t"
+FEED_ARCH_kb9202 = "armv4t"
+FEED_ARCH_ks8695 = "armv4t"
+FEED_ARCH_rx1950 = "armv4t"
+FEED_ARCH_rx3000 = "armv4t"
+FEED_ARCH_sarge-at91 = "armv4t"
+FEED_ARCH_smdk2440 = "armv4t"
+FEED_ARCH_smdk2443 = "armv4t"
#armv5t machines
-FEED_ARCH_a1200 = "armv5te"
-FEED_ARCH_a780 = "armv5te"
-FEED_ARCH_akita = "armv5te"
-FEED_ARCH_asus620 = "armv5te"
-FEED_ARCH_asus730 = "armv5te"
+FEED_ARCH_a1200 = "armv5te"
+FEED_ARCH_a780 = "armv5te"
+FEED_ARCH_akita = "armv5te"
+FEED_ARCH_asus620 = "armv5te"
+FEED_ARCH_asus730 = "armv5te"
FEED_ARCH_at91sam9263ek = "armv5te"
-FEED_ARCH_aximx50 = "armv5te"
-FEED_ARCH_aximx50v = "armv5te"
-FEED_ARCH_c7x0 = "armv5te"
+FEED_ARCH_aximx50 = "armv5te"
+FEED_ARCH_aximx50v = "armv5te"
+FEED_ARCH_c7x0 = "armv5te"
FEED_ARCH_compulab-pxa270 = "armv5te"
FEED_ARCH_davinci-dvevm = "armv5te"
FEED_ARCH_devkitidp-pxa255 = "armv5te"
-FEED_ARCH_e680 = "armv5te"
-FEED_ARCH_er0100 = "armv5te"
-FEED_ARCH_gumstix = "armv5te"
+FEED_ARCH_e680 = "armv5te"
+FEED_ARCH_er0100 = "armv5te"
+FEED_ARCH_gumstix = "armv5te"
FEED_ARCH_gumstix-verdex = "armv5te"
FEED_ARCH_gumstix-connex = "armv5te"
-FEED_ARCH_h1910 = "armv5te"
-FEED_ARCH_h2200 = "armv5te"
-FEED_ARCH_h3900 = "armv5te"
-FEED_ARCH_h4000 = "armv5te"
-FEED_ARCH_h5000 = "armv5te"
-FEED_ARCH_htcalpine = "armv5te"
-FEED_ARCH_htcapache = "armv5te"
-FEED_ARCH_htcblueangel = "armv5te"
-FEED_ARCH_htchimalaya = "armv5te"
-FEED_ARCH_htcsable = "armv5te"
-FEED_ARCH_htctornado = "armv5te"
-FEED_ARCH_htcuniversal = "armv5te"
-FEED_ARCH_hx2000 = "armv5te"
-FEED_ARCH_hx4700 = "armv5te"
-FEED_ARCH_ixp4xxle = "armv5te"
+FEED_ARCH_h1910 = "armv5te"
+FEED_ARCH_h2200 = "armv5te"
+FEED_ARCH_h3900 = "armv5te"
+FEED_ARCH_h4000 = "armv5te"
+FEED_ARCH_h5000 = "armv5te"
+FEED_ARCH_htcalpine = "armv5te"
+FEED_ARCH_htcapache = "armv5te"
+FEED_ARCH_htcblueangel = "armv5te"
+FEED_ARCH_htchimalaya = "armv5te"
+FEED_ARCH_htcsable = "armv5te"
+FEED_ARCH_htctornado = "armv5te"
+FEED_ARCH_htcuniversal = "armv5te"
+FEED_ARCH_hx2000 = "armv5te"
+FEED_ARCH_hx4700 = "armv5te"
+FEED_ARCH_ixp4xxle = "armv5te"
FEED_ARCH_logicpd-pxa270 = "armv5te"
-FEED_ARCH_looxc550 = "armv5te"
-FEED_ARCH_lsarm = "armv5te"
-FEED_ARCH_magician = "armv5te"
-FEED_ARCH_mainstone = "armv5te"
-FEED_ARCH_mnci = "armv5te"
-FEED_ARCH_mtx-3 = "armv5te"
-FEED_ARCH_mx21ads = "armv5te"
-FEED_ARCH_n2100 = "armv5te"
+FEED_ARCH_looxc550 = "armv5te"
+FEED_ARCH_lsarm = "armv5te"
+FEED_ARCH_magician = "armv5te"
+FEED_ARCH_mainstone = "armv5te"
+FEED_ARCH_mnci = "armv5te"
+FEED_ARCH_mtx-3 = "armv5te"
+FEED_ARCH_mx21ads = "armv5te"
+FEED_ARCH_n2100 = "armv5te"
FEED_ARCH_navman-icn330 = "armv5te"
-FEED_ARCH_netbook-pro = "armv5te"
-FEED_ARCH_nokia770 = "armv5te"
-FEED_ARCH_rokre2 = "armv5te"
-FEED_ARCH_nslu2le = "armv5te"
-FEED_ARCH_omap1510inn = "armv5te"
-FEED_ARCH_omap1610h2 = "armv5te"
-FEED_ARCH_omap1710h3 = "armv5te"
-FEED_ARCH_omap5912osk = "armv5te"
-FEED_ARCH_palmld = "armv5te"
-FEED_ARCH_palmt650 = "armv5te"
-FEED_ARCH_palmt680 = "armv5te"
-FEED_ARCH_palmtc = "armv5te"
-FEED_ARCH_palmtt = "armv5te"
-FEED_ARCH_palmtt3 = "armv5te"
-FEED_ARCH_palmtt5 = "armv5te"
-FEED_ARCH_palmtx = "armv5te"
-FEED_ARCH_palmz31 = "armv5te"
-FEED_ARCH_palmz71 = "armv5te"
-FEED_ARCH_palmz72 = "armv5te"
-FEED_ARCH_poodle = "armv5te"
-FEED_ARCH_qemuarm = "armv5te"
-FEED_ARCH_spitz = "armv5te"
-FEED_ARCH_tosa = "armv5te"
-FEED_ARCH_triton = "armv5te"
-
-FEED_ARCH_ixp4xxbe = "armv5teb"
-FEED_ARCH_nslu2be = "armv5teb"
+FEED_ARCH_netbook-pro = "armv5te"
+FEED_ARCH_nokia770 = "armv5te"
+FEED_ARCH_rokre2 = "armv5te"
+FEED_ARCH_nslu2le = "armv5te"
+FEED_ARCH_omap1510inn = "armv5te"
+FEED_ARCH_omap1610h2 = "armv5te"
+FEED_ARCH_omap1710h3 = "armv5te"
+FEED_ARCH_omap5912osk = "armv5te"
+FEED_ARCH_palmld = "armv5te"
+FEED_ARCH_palmt650 = "armv5te"
+FEED_ARCH_palmt680 = "armv5te"
+FEED_ARCH_palmtc = "armv5te"
+FEED_ARCH_palmtt = "armv5te"
+FEED_ARCH_palmtt3 = "armv5te"
+FEED_ARCH_palmtt5 = "armv5te"
+FEED_ARCH_palmtx = "armv5te"
+FEED_ARCH_palmz31 = "armv5te"
+FEED_ARCH_palmz71 = "armv5te"
+FEED_ARCH_palmz72 = "armv5te"
+FEED_ARCH_poodle = "armv5te"
+FEED_ARCH_qemuarm = "armv5te"
+FEED_ARCH_spitz = "armv5te"
+FEED_ARCH_tosa = "armv5te"
+FEED_ARCH_triton = "armv5te"
+
+FEED_ARCH_ixp4xxbe = "armv5teb"
+FEED_ARCH_nslu2be = "armv5teb"
# armv6
-FEED_ARCH_mx31ads = "armv6"
-FEED_ARCH_mx31moboard = "armv6"
-FEED_ARCH_nokia800 = "armv6"
-FEED_ARCH_omap2420h4 = "armv6"
+FEED_ARCH_mx31ads = "armv6"
+FEED_ARCH_mx31moboard = "armv6"
+FEED_ARCH_nokia800 = "armv6"
+FEED_ARCH_omap2420h4 = "armv6"
FEED_ARCH_omap2430sdp = "armv6"
#i486 machines
-FEED_ARCH_geodegx = "i486"
-FEED_ARCH_netvista = "i486"
-FEED_ARCH_wrap = "i486"
-FEED_ARCH_x86 = "i486"
+FEED_ARCH_geodegx = "i486"
+FEED_ARCH_netvista = "i486"
+FEED_ARCH_wrap = "i486"
+FEED_ARCH_x86 = "i486"
#i586 machines
-FEED_ARCH_epia = "i586"
-FEED_ARCH_geodelx = "i586"
-FEED_ARCH_i586-generic = "i586"
-FEED_ARCH_qemux86 = "i586"
+FEED_ARCH_epia = "i586"
+FEED_ARCH_geodelx = "i586"
+FEED_ARCH_i586-generic = "i586"
+FEED_ARCH_qemux86 = "i586"
#i686 machines
-FEED_ARCH_colinux = "i686"
-FEED_ARCH_guinness = "i686"
-FEED_ARCH_i686-generic = "i686"
-FEED_ARCH_progear = "i686"
+FEED_ARCH_colinux = "i686"
+FEED_ARCH_guinness = "i686"
+FEED_ARCH_i686-generic = "i686"
+FEED_ARCH_progear = "i686"
#powerpc machines
-FEED_ARCH_dht-walnut = "ppc405"
-FEED_ARCH_magicbox = "ppc405"
-FEED_ARCH_xilinx-ml403 = "ppc405"
-FEED_ARCH_xilinx-ml410 = "ppc405"
-FEED_ARCH_sequoia = "ppc440e"
-FEED_ARCH_efika = "ppc603e"
-FEED_ARCH_lite5200 = "ppc603e"
-FEED_ARCH_lsppchd = "ppc603e"
-FEED_ARCH_lsppchg = "ppc603e"
-FEED_ARCH_storcenter = "ppc603e"
-FEED_ARCH_turbostation = "ppc603e"
-FEED_ARCH_mpc8313e-rdb = "ppce300c3"
-FEED_ARCH_mpc8323e-rdb = "ppce300c2"
+FEED_ARCH_dht-walnut = "ppc405"
+FEED_ARCH_magicbox = "ppc405"
+FEED_ARCH_xilinx-ml403 = "ppc405"
+FEED_ARCH_xilinx-ml410 = "ppc405"
+FEED_ARCH_sequoia = "ppc440e"
+FEED_ARCH_efika = "ppc603e"
+FEED_ARCH_lite5200 = "ppc603e"
+FEED_ARCH_lsppchd = "ppc603e"
+FEED_ARCH_lsppchg = "ppc603e"
+FEED_ARCH_storcenter = "ppc603e"
+FEED_ARCH_turbostation = "ppc603e"
+FEED_ARCH_mpc8313e-rdb = "ppce300c3"
+FEED_ARCH_mpc8323e-rdb = "ppce300c2"
#strongarm machines, no EABI
-FEED_ARCH_collie = "arm-oabi"
-FEED_ARCH_h3600 = "arm-oabi"
-FEED_ARCH_h3800 = "arm-oabi"
-FEED_ARCH_htcwallaby = "arm-oabi"
-FEED_ARCH_jornada56x = "arm-oabi"
-FEED_ARCH_jornada7xx = "arm-oabi"
-FEED_ARCH_shark = "arm-oabi"
-FEED_ARCH_simpad = "arm-oabi"
+FEED_ARCH_collie = "arm-oabi"
+FEED_ARCH_h3600 = "arm-oabi"
+FEED_ARCH_h3800 = "arm-oabi"
+FEED_ARCH_htcwallaby = "arm-oabi"
+FEED_ARCH_jornada56x = "arm-oabi"
+FEED_ARCH_jornada7xx = "arm-oabi"
+FEED_ARCH_shark = "arm-oabi"
+FEED_ARCH_simpad = "arm-oabi"
#Tweak packaging for strongarm machines since they can't use EABI
@@ -285,7 +285,7 @@ PACKAGE_EXTRA_ARCHS_htcwallaby = "arm-oabi"
IMAGE_NAME = "${DISTRO_NAME}-${IMAGE_BASENAME}-${LIBC}-${ANGSTROM_PKG_FORMAT}-${DISTRO_VERSION}-${MACHINE}"
DEPLOY_DIR_IMAGE = "${DEPLOY_DIR}/images/${MACHINE}"
-# KaeilOS *always* has some form of release config, so error out if someone thinks he knows better
+# KaeilOS *always* has some form of release config, so error out if someone thinks he knows better
DISTRO_CHECK := "${@bb.data.getVar("DISTRO_VERSION",d,1) or bb.fatal('Remove this line or set a dummy DISTRO_VERSION if you really want to build an unversioned distro')}"
# We want images supporting the following features (for task-base)
diff --git a/conf/distro/include/sane-feed.inc b/conf/distro/include/sane-feed.inc
index 2673f9d..31a7255 100644
--- a/conf/distro/include/sane-feed.inc
+++ b/conf/distro/include/sane-feed.inc
@@ -18,147 +18,147 @@ FEED_ARCH_bfin = "blackfin"
# armv4t machines
-FEED_ARCH_acern30 = "armv4t"
-FEED_ARCH_amsdelta = "armv4t"
-FEED_ARCH_ep93xx = "armv4t"
-FEED_ARCH_eteng500 = "armv4t"
-FEED_ARCH_om-gta01 = "armv4t"
-FEED_ARCH_om-gta02 = "armv4t"
-FEED_ARCH_h1940 = "armv4t"
-FEED_ARCH_h6300 = "armv4t"
-FEED_ARCH_kb9202 = "armv4t"
-FEED_ARCH_ks8695 = "armv4t"
-FEED_ARCH_rx1950 = "armv4t"
-FEED_ARCH_rx3000 = "armv4t"
-FEED_ARCH_sarge-at91 = "armv4t"
-FEED_ARCH_smdk2440 = "armv4t"
-FEED_ARCH_smdk2443 = "armv4t"
+FEED_ARCH_acern30 = "armv4t"
+FEED_ARCH_amsdelta = "armv4t"
+FEED_ARCH_ep93xx = "armv4t"
+FEED_ARCH_eteng500 = "armv4t"
+FEED_ARCH_om-gta01 = "armv4t"
+FEED_ARCH_om-gta02 = "armv4t"
+FEED_ARCH_h1940 = "armv4t"
+FEED_ARCH_h6300 = "armv4t"
+FEED_ARCH_kb9202 = "armv4t"
+FEED_ARCH_ks8695 = "armv4t"
+FEED_ARCH_rx1950 = "armv4t"
+FEED_ARCH_rx3000 = "armv4t"
+FEED_ARCH_sarge-at91 = "armv4t"
+FEED_ARCH_smdk2440 = "armv4t"
+FEED_ARCH_smdk2443 = "armv4t"
# armv5t machines
-FEED_ARCH_a1200 = "armv5te"
-FEED_ARCH_a780 = "armv5te"
-FEED_ARCH_akita = "armv5te"
-FEED_ARCH_asus620 = "armv5te"
-FEED_ARCH_asus730 = "armv5te"
+FEED_ARCH_a1200 = "armv5te"
+FEED_ARCH_a780 = "armv5te"
+FEED_ARCH_akita = "armv5te"
+FEED_ARCH_asus620 = "armv5te"
+FEED_ARCH_asus730 = "armv5te"
FEED_ARCH_at91sam9263ek = "armv5te"
-FEED_ARCH_aximx50 = "armv5te"
-FEED_ARCH_aximx50v = "armv5te"
-FEED_ARCH_c7x0 = "armv5te"
+FEED_ARCH_aximx50 = "armv5te"
+FEED_ARCH_aximx50v = "armv5te"
+FEED_ARCH_c7x0 = "armv5te"
FEED_ARCH_compulab-pxa270 = "armv5te"
FEED_ARCH_davinci-dvevm = "armv5te"
FEED_ARCH_devkitidp-pxa255 = "armv5te"
-FEED_ARCH_e680 = "armv5te"
-FEED_ARCH_er0100 = "armv5te"
-FEED_ARCH_gumstix = "armv5te"
+FEED_ARCH_e680 = "armv5te"
+FEED_ARCH_er0100 = "armv5te"
+FEED_ARCH_gumstix = "armv5te"
FEED_ARCH_gumstix-verdex = "armv5te"
FEED_ARCH_gumstix-connex = "armv5te"
-FEED_ARCH_h1910 = "armv5te"
-FEED_ARCH_h2200 = "armv5te"
-FEED_ARCH_h3900 = "armv5te"
-FEED_ARCH_h4000 = "armv5te"
-FEED_ARCH_h5000 = "armv5te"
-FEED_ARCH_htcalpine = "armv5te"
-FEED_ARCH_htcapache = "armv5te"
-FEED_ARCH_htcblueangel = "armv5te"
-FEED_ARCH_htchimalaya = "armv5te"
-FEED_ARCH_htcsable = "armv5te"
-FEED_ARCH_htctornado = "armv5te"
-FEED_ARCH_htcuniversal = "armv5te"
-FEED_ARCH_hx2000 = "armv5te"
-FEED_ARCH_hx4700 = "armv5te"
-FEED_ARCH_ixp4xxle = "armv5te"
+FEED_ARCH_h1910 = "armv5te"
+FEED_ARCH_h2200 = "armv5te"
+FEED_ARCH_h3900 = "armv5te"
+FEED_ARCH_h4000 = "armv5te"
+FEED_ARCH_h5000 = "armv5te"
+FEED_ARCH_htcalpine = "armv5te"
+FEED_ARCH_htcapache = "armv5te"
+FEED_ARCH_htcblueangel = "armv5te"
+FEED_ARCH_htchimalaya = "armv5te"
+FEED_ARCH_htcsable = "armv5te"
+FEED_ARCH_htctornado = "armv5te"
+FEED_ARCH_htcuniversal = "armv5te"
+FEED_ARCH_hx2000 = "armv5te"
+FEED_ARCH_hx4700 = "armv5te"
+FEED_ARCH_ixp4xxle = "armv5te"
FEED_ARCH_logicpd-pxa270 = "armv5te"
-FEED_ARCH_looxc550 = "armv5te"
-FEED_ARCH_lsarm = "armv5te"
-FEED_ARCH_magician = "armv5te"
-FEED_ARCH_mainstone = "armv5te"
-FEED_ARCH_mnci = "armv5te"
-FEED_ARCH_mtx-3 = "armv5te"
-FEED_ARCH_mx21ads = "armv5te"
-FEED_ARCH_n2100 = "armv5te"
+FEED_ARCH_looxc550 = "armv5te"
+FEED_ARCH_lsarm = "armv5te"
+FEED_ARCH_magician = "armv5te"
+FEED_ARCH_mainstone = "armv5te"
+FEED_ARCH_mnci = "armv5te"
+FEED_ARCH_mtx-3 = "armv5te"
+FEED_ARCH_mx21ads = "armv5te"
+FEED_ARCH_n2100 = "armv5te"
FEED_ARCH_navman-icn330 = "armv5te"
-FEED_ARCH_netbook-pro = "armv5te"
-FEED_ARCH_nokia770 = "armv5te"
-FEED_ARCH_rokre2 = "armv5te"
-FEED_ARCH_nslu2le = "armv5te"
-FEED_ARCH_omap1510inn = "armv5te"
-FEED_ARCH_omap1610h2 = "armv5te"
-FEED_ARCH_omap1710h3 = "armv5te"
-FEED_ARCH_omap5912osk = "armv5te"
-FEED_ARCH_palmld = "armv5te"
-FEED_ARCH_palmt650 = "armv5te"
-FEED_ARCH_palmt680 = "armv5te"
-FEED_ARCH_palmtc = "armv5te"
-FEED_ARCH_palmtt = "armv5te"
-FEED_ARCH_palmtt3 = "armv5te"
-FEED_ARCH_palmtt5 = "armv5te"
-FEED_ARCH_palmtx = "armv5te"
-FEED_ARCH_palmz31 = "armv5te"
-FEED_ARCH_palmz71 = "armv5te"
-FEED_ARCH_palmz72 = "armv5te"
-FEED_ARCH_poodle = "armv5te"
-FEED_ARCH_qemuarm = "armv5te"
-FEED_ARCH_spitz = "armv5te"
-FEED_ARCH_tosa = "armv5te"
-FEED_ARCH_triton = "armv5te"
-
-FEED_ARCH_ixp4xxbe = "armv5teb"
-FEED_ARCH_nslu2be = "armv5teb"
+FEED_ARCH_netbook-pro = "armv5te"
+FEED_ARCH_nokia770 = "armv5te"
+FEED_ARCH_rokre2 = "armv5te"
+FEED_ARCH_nslu2le = "armv5te"
+FEED_ARCH_omap1510inn = "armv5te"
+FEED_ARCH_omap1610h2 = "armv5te"
+FEED_ARCH_omap1710h3 = "armv5te"
+FEED_ARCH_omap5912osk = "armv5te"
+FEED_ARCH_palmld = "armv5te"
+FEED_ARCH_palmt650 = "armv5te"
+FEED_ARCH_palmt680 = "armv5te"
+FEED_ARCH_palmtc = "armv5te"
+FEED_ARCH_palmtt = "armv5te"
+FEED_ARCH_palmtt3 = "armv5te"
+FEED_ARCH_palmtt5 = "armv5te"
+FEED_ARCH_palmtx = "armv5te"
+FEED_ARCH_palmz31 = "armv5te"
+FEED_ARCH_palmz71 = "armv5te"
+FEED_ARCH_palmz72 = "armv5te"
+FEED_ARCH_poodle = "armv5te"
+FEED_ARCH_qemuarm = "armv5te"
+FEED_ARCH_spitz = "armv5te"
+FEED_ARCH_tosa = "armv5te"
+FEED_ARCH_triton = "armv5te"
+
+FEED_ARCH_ixp4xxbe = "armv5teb"
+FEED_ARCH_nslu2be = "armv5teb"
# armv6 machines
-FEED_ARCH_mx31ads = "armv6"
-FEED_ARCH_mx31moboard = "armv6"
-FEED_ARCH_nokia800 = "armv6"
-FEED_ARCH_omap2420h4 = "armv6"
+FEED_ARCH_mx31ads = "armv6"
+FEED_ARCH_mx31moboard = "armv6"
+FEED_ARCH_nokia800 = "armv6"
+FEED_ARCH_omap2420h4 = "armv6"
FEED_ARCH_omap2430sdp = "armv6"
# i486 machines
-FEED_ARCH_geodegx = "i486"
-FEED_ARCH_netvista = "i486"
-FEED_ARCH_wrap = "i486"
-FEED_ARCH_x86 = "i486"
+FEED_ARCH_geodegx = "i486"
+FEED_ARCH_netvista = "i486"
+FEED_ARCH_wrap = "i486"
+FEED_ARCH_x86 = "i486"
# i586 machines
-FEED_ARCH_epia = "i586"
-FEED_ARCH_geodelx = "i586"
-FEED_ARCH_i586-generic = "i586"
-FEED_ARCH_qemux86 = "i586"
+FEED_ARCH_epia = "i586"
+FEED_ARCH_geodelx = "i586"
+FEED_ARCH_i586-generic = "i586"
+FEED_ARCH_qemux86 = "i586"
# i686 machines
-FEED_ARCH_colinux = "i686"
-FEED_ARCH_guinness = "i686"
-FEED_ARCH_i686-generic = "i686"
-FEED_ARCH_progear = "i686"
+FEED_ARCH_colinux = "i686"
+FEED_ARCH_guinness = "i686"
+FEED_ARCH_i686-generic = "i686"
+FEED_ARCH_progear = "i686"
# powerpc machines
-FEED_ARCH_dht-walnut = "ppc405"
-FEED_ARCH_magicbox = "ppc405"
-FEED_ARCH_xilinx-ml403 = "ppc405"
-FEED_ARCH_xilinx-ml410 = "ppc405"
-FEED_ARCH_sequoia = "ppc440e"
-FEED_ARCH_efika = "ppc603e"
-FEED_ARCH_lite5200 = "ppc603e"
-FEED_ARCH_lsppchd = "ppc603e"
-FEED_ARCH_lsppchg = "ppc603e"
-FEED_ARCH_storcenter = "ppc603e"
-FEED_ARCH_turbostation = "ppc603e"
-FEED_ARCH_mpc8313e-rdb = "ppce300c3"
-FEED_ARCH_mpc8323e-rdb = "ppce300c2"
+FEED_ARCH_dht-walnut = "ppc405"
+FEED_ARCH_magicbox = "ppc405"
+FEED_ARCH_xilinx-ml403 = "ppc405"
+FEED_ARCH_xilinx-ml410 = "ppc405"
+FEED_ARCH_sequoia = "ppc440e"
+FEED_ARCH_efika = "ppc603e"
+FEED_ARCH_lite5200 = "ppc603e"
+FEED_ARCH_lsppchd = "ppc603e"
+FEED_ARCH_lsppchg = "ppc603e"
+FEED_ARCH_storcenter = "ppc603e"
+FEED_ARCH_turbostation = "ppc603e"
+FEED_ARCH_mpc8313e-rdb = "ppce300c3"
+FEED_ARCH_mpc8323e-rdb = "ppce300c2"
# strongarm machines, no EABI
-FEED_ARCH_collie = "arm-oabi"
-FEED_ARCH_h3600 = "arm-oabi"
-FEED_ARCH_h3800 = "arm-oabi"
-FEED_ARCH_htcwallaby = "arm-oabi"
-FEED_ARCH_jornada56x = "arm-oabi"
-FEED_ARCH_jornada7xx = "arm-oabi"
-FEED_ARCH_shark = "arm-oabi"
-FEED_ARCH_simpad = "arm-oabi"
+FEED_ARCH_collie = "arm-oabi"
+FEED_ARCH_h3600 = "arm-oabi"
+FEED_ARCH_h3800 = "arm-oabi"
+FEED_ARCH_htcwallaby = "arm-oabi"
+FEED_ARCH_jornada56x = "arm-oabi"
+FEED_ARCH_jornada7xx = "arm-oabi"
+FEED_ARCH_shark = "arm-oabi"
+FEED_ARCH_simpad = "arm-oabi"
# Tweak packaging for strongarm machines since they can't use EABI
--
1.6.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 4/6] kaeilos: use include/sane-feed.inc
2009-05-13 14:46 Some updates for GeodeLX based devices Marcin Juszkiewicz
` (2 preceding siblings ...)
2009-05-13 14:46 ` [PATCH 3/6] kaeilos.inc/sane-feed.inc: use spaces instead of tabs Marcin Juszkiewicz
@ 2009-05-13 14:46 ` Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 5/6] linux: drop alix, move geodelx to 2.6.29 Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices Marcin Juszkiewicz
5 siblings, 0 replies; 17+ messages in thread
From: Marcin Juszkiewicz @ 2009-05-13 14:46 UTC (permalink / raw)
To: openembedded-devel; +Cc: Marcin Juszkiewicz
From: Marcin Juszkiewicz <hrw@openembedded.org>
Signed-off-by: Marcin Juszkiewicz <hrw@openembedded.org>
---
conf/distro/include/kaeilos.inc | 163 +--------------------------------------
1 files changed, 1 insertions(+), 162 deletions(-)
diff --git a/conf/distro/include/kaeilos.inc b/conf/distro/include/kaeilos.inc
index d34849f..97132cb 100644
--- a/conf/distro/include/kaeilos.inc
+++ b/conf/distro/include/kaeilos.inc
@@ -118,168 +118,7 @@ TARGET_FPU_ppc603e ?= "hard"
TARGET_CC_ARCH_pn-webkit-gtk_armv5te = "-march=armv4t"
TARGET_CC_ARCH_pn-cairo_armv5te = "-march=armv4t"
-#Set the right arch for the feeds
-#Alphabetically sorted
-
-FEED_ARCH ?= "${TARGET_ARCH}"
-
-#blackfin machines
-FEED_ARCH_bfin = "blackfin"
-
-#armv4t machines
-
-FEED_ARCH_acern30 = "armv4t"
-FEED_ARCH_amsdelta = "armv4t"
-FEED_ARCH_ep93xx = "armv4t"
-FEED_ARCH_eteng500 = "armv4t"
-FEED_ARCH_om-gta01 = "armv4t"
-FEED_ARCH_om-gta02 = "armv4t"
-FEED_ARCH_h1940 = "armv4t"
-FEED_ARCH_h6300 = "armv4t"
-FEED_ARCH_kb9202 = "armv4t"
-FEED_ARCH_ks8695 = "armv4t"
-FEED_ARCH_rx1950 = "armv4t"
-FEED_ARCH_rx3000 = "armv4t"
-FEED_ARCH_sarge-at91 = "armv4t"
-FEED_ARCH_smdk2440 = "armv4t"
-FEED_ARCH_smdk2443 = "armv4t"
-
-#armv5t machines
-
-FEED_ARCH_a1200 = "armv5te"
-FEED_ARCH_a780 = "armv5te"
-FEED_ARCH_akita = "armv5te"
-FEED_ARCH_asus620 = "armv5te"
-FEED_ARCH_asus730 = "armv5te"
-FEED_ARCH_at91sam9263ek = "armv5te"
-FEED_ARCH_aximx50 = "armv5te"
-FEED_ARCH_aximx50v = "armv5te"
-FEED_ARCH_c7x0 = "armv5te"
-FEED_ARCH_compulab-pxa270 = "armv5te"
-FEED_ARCH_davinci-dvevm = "armv5te"
-FEED_ARCH_devkitidp-pxa255 = "armv5te"
-FEED_ARCH_e680 = "armv5te"
-FEED_ARCH_er0100 = "armv5te"
-FEED_ARCH_gumstix = "armv5te"
-FEED_ARCH_gumstix-verdex = "armv5te"
-FEED_ARCH_gumstix-connex = "armv5te"
-FEED_ARCH_h1910 = "armv5te"
-FEED_ARCH_h2200 = "armv5te"
-FEED_ARCH_h3900 = "armv5te"
-FEED_ARCH_h4000 = "armv5te"
-FEED_ARCH_h5000 = "armv5te"
-FEED_ARCH_htcalpine = "armv5te"
-FEED_ARCH_htcapache = "armv5te"
-FEED_ARCH_htcblueangel = "armv5te"
-FEED_ARCH_htchimalaya = "armv5te"
-FEED_ARCH_htcsable = "armv5te"
-FEED_ARCH_htctornado = "armv5te"
-FEED_ARCH_htcuniversal = "armv5te"
-FEED_ARCH_hx2000 = "armv5te"
-FEED_ARCH_hx4700 = "armv5te"
-FEED_ARCH_ixp4xxle = "armv5te"
-FEED_ARCH_logicpd-pxa270 = "armv5te"
-FEED_ARCH_looxc550 = "armv5te"
-FEED_ARCH_lsarm = "armv5te"
-FEED_ARCH_magician = "armv5te"
-FEED_ARCH_mainstone = "armv5te"
-FEED_ARCH_mnci = "armv5te"
-FEED_ARCH_mtx-3 = "armv5te"
-FEED_ARCH_mx21ads = "armv5te"
-FEED_ARCH_n2100 = "armv5te"
-FEED_ARCH_navman-icn330 = "armv5te"
-FEED_ARCH_netbook-pro = "armv5te"
-FEED_ARCH_nokia770 = "armv5te"
-FEED_ARCH_rokre2 = "armv5te"
-FEED_ARCH_nslu2le = "armv5te"
-FEED_ARCH_omap1510inn = "armv5te"
-FEED_ARCH_omap1610h2 = "armv5te"
-FEED_ARCH_omap1710h3 = "armv5te"
-FEED_ARCH_omap5912osk = "armv5te"
-FEED_ARCH_palmld = "armv5te"
-FEED_ARCH_palmt650 = "armv5te"
-FEED_ARCH_palmt680 = "armv5te"
-FEED_ARCH_palmtc = "armv5te"
-FEED_ARCH_palmtt = "armv5te"
-FEED_ARCH_palmtt3 = "armv5te"
-FEED_ARCH_palmtt5 = "armv5te"
-FEED_ARCH_palmtx = "armv5te"
-FEED_ARCH_palmz31 = "armv5te"
-FEED_ARCH_palmz71 = "armv5te"
-FEED_ARCH_palmz72 = "armv5te"
-FEED_ARCH_poodle = "armv5te"
-FEED_ARCH_qemuarm = "armv5te"
-FEED_ARCH_spitz = "armv5te"
-FEED_ARCH_tosa = "armv5te"
-FEED_ARCH_triton = "armv5te"
-
-FEED_ARCH_ixp4xxbe = "armv5teb"
-FEED_ARCH_nslu2be = "armv5teb"
-
-# armv6
-
-FEED_ARCH_mx31ads = "armv6"
-FEED_ARCH_mx31moboard = "armv6"
-FEED_ARCH_nokia800 = "armv6"
-FEED_ARCH_omap2420h4 = "armv6"
-FEED_ARCH_omap2430sdp = "armv6"
-
-#i486 machines
-FEED_ARCH_geodegx = "i486"
-FEED_ARCH_netvista = "i486"
-FEED_ARCH_wrap = "i486"
-FEED_ARCH_x86 = "i486"
-
-#i586 machines
-FEED_ARCH_epia = "i586"
-FEED_ARCH_geodelx = "i586"
-FEED_ARCH_i586-generic = "i586"
-FEED_ARCH_qemux86 = "i586"
-
-#i686 machines
-
-FEED_ARCH_colinux = "i686"
-FEED_ARCH_guinness = "i686"
-FEED_ARCH_i686-generic = "i686"
-FEED_ARCH_progear = "i686"
-
-#powerpc machines
-
-FEED_ARCH_dht-walnut = "ppc405"
-FEED_ARCH_magicbox = "ppc405"
-FEED_ARCH_xilinx-ml403 = "ppc405"
-FEED_ARCH_xilinx-ml410 = "ppc405"
-FEED_ARCH_sequoia = "ppc440e"
-FEED_ARCH_efika = "ppc603e"
-FEED_ARCH_lite5200 = "ppc603e"
-FEED_ARCH_lsppchd = "ppc603e"
-FEED_ARCH_lsppchg = "ppc603e"
-FEED_ARCH_storcenter = "ppc603e"
-FEED_ARCH_turbostation = "ppc603e"
-FEED_ARCH_mpc8313e-rdb = "ppce300c3"
-FEED_ARCH_mpc8323e-rdb = "ppce300c2"
-
-
-#strongarm machines, no EABI
-
-FEED_ARCH_collie = "arm-oabi"
-FEED_ARCH_h3600 = "arm-oabi"
-FEED_ARCH_h3800 = "arm-oabi"
-FEED_ARCH_htcwallaby = "arm-oabi"
-FEED_ARCH_jornada56x = "arm-oabi"
-FEED_ARCH_jornada7xx = "arm-oabi"
-FEED_ARCH_shark = "arm-oabi"
-FEED_ARCH_simpad = "arm-oabi"
-
-
-#Tweak packaging for strongarm machines since they can't use EABI
-
-PACKAGE_EXTRA_ARCHS_collie = "arm-oabi"
-PACKAGE_EXTRA_ARCHS_h3600 = "arm-oabi"
-PACKAGE_EXTRA_ARCHS_h3800 = "arm-oabi"
-PACKAGE_EXTRA_ARCHS_simpad = "arm-oabi"
-PACKAGE_EXTRA_ARCHS_htcwallaby = "arm-oabi"
-
+require conf/distro/include/sane-feed.inc
#Name the generated images in a sane way
IMAGE_NAME = "${DISTRO_NAME}-${IMAGE_BASENAME}-${LIBC}-${ANGSTROM_PKG_FORMAT}-${DISTRO_VERSION}-${MACHINE}"
--
1.6.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 5/6] linux: drop alix, move geodelx to 2.6.29
2009-05-13 14:46 Some updates for GeodeLX based devices Marcin Juszkiewicz
` (3 preceding siblings ...)
2009-05-13 14:46 ` [PATCH 4/6] kaeilos: use include/sane-feed.inc Marcin Juszkiewicz
@ 2009-05-13 14:46 ` Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices Marcin Juszkiewicz
5 siblings, 0 replies; 17+ messages in thread
From: Marcin Juszkiewicz @ 2009-05-13 14:46 UTC (permalink / raw)
To: openembedded-devel; +Cc: Marcin Juszkiewicz
From: Marcin Juszkiewicz <hrw@openembedded.org>
Signed-off-by: Marcin Juszkiewicz <hrw@openembedded.org>
---
.../geode-mfgpt-clock-event-device-support.patch | 237 ---
...de-mfgpt-support-for-geode-class-machines.patch | 311 ----
recipes/linux/linux/{alix => geodelx}/defconfig | 1599 ++++++++++++++------
recipes/linux/linux_2.6.25.bb | 1 -
recipes/linux/linux_2.6.29.bb | 1 +
5 files changed, 1115 insertions(+), 1034 deletions(-)
delete mode 100644 recipes/linux/linux/alix/geode-mfgpt-clock-event-device-support.patch
delete mode 100644 recipes/linux/linux/alix/geode-mfgpt-support-for-geode-class-machines.patch
rename recipes/linux/linux/{alix => geodelx}/defconfig (57%)
diff --git a/recipes/linux/linux/alix/geode-mfgpt-clock-event-device-support.patch b/recipes/linux/linux/alix/geode-mfgpt-clock-event-device-support.patch
deleted file mode 100644
index 6f0b10a..0000000
--- a/recipes/linux/linux/alix/geode-mfgpt-clock-event-device-support.patch
+++ /dev/null
@@ -1,237 +0,0 @@
-From: Andres Salomon <dilinger@queued.net>
-
-Add support for an MFGPT clock event device; this allows us to use MFGPTs as
-the basis for high-resolution timers.
-
-Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
-Signed-off-by: Andres Salomon <dilinger@debian.org>
-Cc: Andi Kleen <ak@suse.de>
-Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
-Cc: john stultz <johnstul@us.ibm.com>
-Cc: Thomas Gleixner <tglx@linutronix.de>
-Cc: Ingo Molnar <mingo@elte.hu>
-Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
----
-
- Documentation/kernel-parameters.txt | 4
- arch/i386/Kconfig | 10 +
- arch/i386/kernel/mfgpt.c | 165 ++++++++++++++++++++++++++
- 3 files changed, 179 insertions(+)
-
---- linux-2.6.22.orig/Documentation/kernel-parameters.txt
-+++ linux-2.6.22/Documentation/kernel-parameters.txt
-@@ -1012,6 +1012,10 @@
- meye.*= [HW] Set MotionEye Camera parameters
- See Documentation/video4linux/meye.txt.
-
-+ mfgpt_irq= [IA-32] Specify the IRQ to use for the
-+ Multi-Function General Purpose Timers on AMD Geode
-+ platforms.
-+
- mga= [HW,DRM]
-
- migration_cost=
---- linux-2.6.22.orig/arch/i386/Kconfig
-+++ linux-2.6.22/arch/i386/Kconfig
-@@ -1190,6 +1190,16 @@
- processor goes idle (as is done by the scheduler). The
- other workaround is idle=poll boot option.
-
-+config GEODE_MFGPT_TIMER
-+ bool "Geode Multi-Function General Purpose Timer (MFGPT) events"
-+ depends on MGEODE_LX && GENERIC_TIME && GENERIC_CLOCKEVENTS
-+ default y
-+ help
-+ This driver provides a clock event source based on the MFGPT
-+ timer(s) in the CS5535 and CS5536 companion chip for the geode.
-+ MFGPTs have a better resolution and max interval than the
-+ generic PIT, and are suitable for use as high-res timers.
-+
- config K8_NB
- def_bool y
- depends on AGP_AMD64
---- linux-2.6.22.orig/arch/i386/kernel/mfgpt.c
-+++ linux-2.6.22/arch/i386/kernel/mfgpt.c
-@@ -48,6 +48,12 @@
- #define MFGPT_HZ (32000 / MFGPT_DIVISOR)
- #define MFGPT_PERIODIC (MFGPT_HZ / HZ)
-
-+#ifdef CONFIG_GEODE_MFGPT_TIMER
-+static int __init mfgpt_timer_setup(void);
-+#else
-+#define mfgpt_timer_setup() (0)
-+#endif
-+
- /* Allow for disabling of MFGPTs */
- static int disable;
- static int __init mfgpt_disable(char *s)
-@@ -82,6 +88,9 @@
- }
- }
-
-+ /* set up clock event device, if desired */
-+ i = mfgpt_timer_setup();
-+
- return count;
- }
-
-@@ -197,3 +206,159 @@
- return -1;
- }
- EXPORT_SYMBOL(geode_mfgpt_alloc_timer);
-+
-+#ifdef CONFIG_GEODE_MFGPT_TIMER
-+
-+/*
-+ * The MFPGT timers on the CS5536 provide us with suitable timers to use
-+ * as clock event sources - not as good as a HPET or APIC, but certainly
-+ * better then the PIT. This isn't a general purpose MFGPT driver, but
-+ * a simplified one designed specifically to act as a clock event source.
-+ * For full details about the MFGPT, please consult the CS5536 data sheet.
-+ */
-+
-+#include <linux/clocksource.h>
-+#include <linux/clockchips.h>
-+
-+static unsigned int mfgpt_tick_mode = CLOCK_EVT_MODE_SHUTDOWN;
-+static u16 mfgpt_event_clock;
-+
-+static int irq = 7;
-+static int __init mfgpt_setup(char *str)
-+{
-+ get_option(&str, &irq);
-+ return 1;
-+}
-+__setup("mfgpt_irq=", mfgpt_setup);
-+
-+static inline void mfgpt_disable_timer(u16 clock)
-+{
-+ u16 val = geode_mfgpt_read(clock, MFGPT_REG_SETUP);
-+ geode_mfgpt_write(clock, MFGPT_REG_SETUP, val & ~MFGPT_SETUP_CNTEN);
-+}
-+
-+static int mfgpt_next_event(unsigned long, struct clock_event_device *);
-+static void mfgpt_set_mode(enum clock_event_mode, struct clock_event_device *);
-+
-+static struct clock_event_device mfgpt_clockevent = {
-+ .name = "mfgpt-timer",
-+ .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-+ .set_mode = mfgpt_set_mode,
-+ .set_next_event = mfgpt_next_event,
-+ .rating = 250,
-+ .cpumask = CPU_MASK_ALL,
-+ .shift = 32
-+};
-+
-+static inline void mfgpt_start_timer(u16 clock, u16 delta)
-+{
-+ geode_mfgpt_write(mfgpt_event_clock, MFGPT_REG_CMP2, (u16) delta);
-+ geode_mfgpt_write(mfgpt_event_clock, MFGPT_REG_COUNTER, 0);
-+
-+ geode_mfgpt_write(mfgpt_event_clock, MFGPT_REG_SETUP,
-+ MFGPT_SETUP_CNTEN | MFGPT_SETUP_CMP2);
-+}
-+
-+static void mfgpt_set_mode(enum clock_event_mode mode,
-+ struct clock_event_device *evt)
-+{
-+ mfgpt_disable_timer(mfgpt_event_clock);
-+
-+ if (mode == CLOCK_EVT_MODE_PERIODIC)
-+ mfgpt_start_timer(mfgpt_event_clock, MFGPT_PERIODIC);
-+
-+ mfgpt_tick_mode = mode;
-+}
-+
-+static int mfgpt_next_event(unsigned long delta, struct clock_event_device *evt)
-+{
-+ mfgpt_start_timer(mfgpt_event_clock, delta);
-+ return 0;
-+}
-+
-+/* Assume (foolishly?), that this interrupt was due to our tick */
-+
-+static irqreturn_t mfgpt_tick(int irq, void *dev_id)
-+{
-+ if (mfgpt_tick_mode == CLOCK_EVT_MODE_SHUTDOWN)
-+ return IRQ_HANDLED;
-+
-+ /* Turn off the clock */
-+ mfgpt_disable_timer(mfgpt_event_clock);
-+
-+ /* Clear the counter */
-+ geode_mfgpt_write(mfgpt_event_clock, MFGPT_REG_COUNTER, 0);
-+
-+ /* Restart the clock in periodic mode */
-+
-+ if (mfgpt_tick_mode == CLOCK_EVT_MODE_PERIODIC) {
-+ geode_mfgpt_write(mfgpt_event_clock, MFGPT_REG_SETUP,
-+ MFGPT_SETUP_CNTEN | MFGPT_SETUP_CMP2);
-+ }
-+
-+ mfgpt_clockevent.event_handler(&mfgpt_clockevent);
-+ return IRQ_HANDLED;
-+}
-+
-+static struct irqaction mfgptirq = {
-+ .handler = mfgpt_tick,
-+ .flags = IRQF_DISABLED | IRQF_NOBALANCING,
-+ .mask = CPU_MASK_NONE,
-+ .name = "mfgpt-timer"
-+};
-+
-+static int __init mfgpt_timer_setup(void)
-+{
-+ int timer, ret;
-+ u16 val;
-+
-+ timer = geode_mfgpt_alloc_timer(MFGPT_TIMER_ANY, MFGPT_DOMAIN_WORKING,
-+ THIS_MODULE);
-+ if (timer < 0) {
-+ printk(KERN_ERR "mfgpt-timer: Could not allocate a MFPGT "
-+ "timer\n");
-+ return -ENODEV;
-+ }
-+
-+ mfgpt_event_clock = timer;
-+ /* Set the clock scale and enable the event mode for CMP2 */
-+ val = MFGPT_SCALE | (3 << 8);
-+
-+ geode_mfgpt_write(mfgpt_event_clock, MFGPT_REG_SETUP, val);
-+
-+ /* Set up the IRQ on the MFGPT side */
-+ if (geode_mfgpt_setup_irq(mfgpt_event_clock, MFGPT_CMP2, irq)) {
-+ printk(KERN_ERR "mfgpt-timer: Could not set up IRQ %d\n", irq);
-+ return -EIO;
-+ }
-+
-+ /* And register it with the kernel */
-+ ret = setup_irq(irq, &mfgptirq);
-+
-+ if (ret) {
-+ printk(KERN_ERR "mfgpt-timer: Unable to set up the "
-+ "interrupt.\n");
-+ goto err;
-+ }
-+
-+ /* Set up the clock event */
-+ mfgpt_clockevent.mult = div_sc(MFGPT_HZ, NSEC_PER_SEC, 32);
-+ mfgpt_clockevent.min_delta_ns = clockevent_delta2ns(0xF,
-+ &mfgpt_clockevent);
-+ mfgpt_clockevent.max_delta_ns = clockevent_delta2ns(0xFFFE,
-+ &mfgpt_clockevent);
-+
-+ printk(KERN_INFO "mfgpt-timer: registering the MFGT timer as a "
-+ "clock event.\n");
-+ clockevents_register_device(&mfgpt_clockevent);
-+
-+ return 0;
-+
-+err:
-+ geode_mfgpt_release_irq(mfgpt_event_clock, MFGPT_CMP2, irq);
-+ printk(KERN_ERR "mfgpt-timer: Unable to set up the MFGPT clock "
-+ "source\n");
-+ return -EIO;
-+}
-+
-+#endif
diff --git a/recipes/linux/linux/alix/geode-mfgpt-support-for-geode-class-machines.patch b/recipes/linux/linux/alix/geode-mfgpt-support-for-geode-class-machines.patch
deleted file mode 100644
index 533412c..0000000
--- a/recipes/linux/linux/alix/geode-mfgpt-support-for-geode-class-machines.patch
+++ /dev/null
@@ -1,311 +0,0 @@
-From: Andres Salomon <dilinger@queued.net>
-
-This adds support for Multi-Function General Purpose Timers. It detects the
-available timers during southbridge init, and provides an API for allocating
-and setting the timers. They're higher resolution than the standard PIT, so
-the MFGPTs come in handy for quite a few things.
-
-Note that we never clobber the timers that the BIOS might have opted to use;
-we just check for unused timers.
-
-Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
-Signed-off-by: Andres Salomon <dilinger@debian.org>
-Cc: Andi Kleen <ak@suse.de>
-Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
-Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
----
-
- Documentation/kernel-parameters.txt | 3
- arch/i386/kernel/Makefile | 2
- arch/i386/kernel/geode.c | 4
- arch/i386/kernel/mfgpt.c | 199 ++++++++++++++++++++++++++
- include/asm-i386/geode.h | 50 ++++++
- 5 files changed, 257 insertions(+), 1 deletion(-)
-
---- linux-2.6.22.orig/arch/i386/kernel/Makefile
-+++ linux-2.6.22/arch/i386/kernel/Makefile
-@@ -40,7 +40,7 @@
- obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
- obj-$(CONFIG_HPET_TIMER) += hpet.o
- obj-$(CONFIG_K8_NB) += k8.o
--obj-$(CONFIG_MGEODE_LX) += geode.o
-+obj-$(CONFIG_MGEODE_LX) += geode.o mfgpt.o
-
- obj-$(CONFIG_VMI) += vmi.o vmiclock.o
- obj-$(CONFIG_PARAVIRT) += paravirt.o
---- linux-2.6.22.orig/arch/i386/kernel/geode.c
-+++ linux-2.6.22/arch/i386/kernel/geode.c
-@@ -146,10 +146,14 @@
-
- static int __init geode_southbridge_init(void)
- {
-+ int timers;
-+
- if (!is_geode())
- return -ENODEV;
-
- init_lbars();
-+ timers = geode_mfgpt_detect();
-+ printk(KERN_INFO "geode: %d MFGPT timers available.\n", timers);
- return 0;
- }
-
---- /dev/null
-+++ linux-2.6.22/arch/i386/kernel/mfgpt.c
-@@ -0,0 +1,199 @@
-+/*
-+ * Driver/API for AMD Geode Multi-Function General Purpose Timers (MFGPT)
-+ *
-+ * Copyright (C) 2006, Advanced Micro Devices, Inc.
-+ * Copyright (C) 2007, Andres Salomon <dilinger@debian.org>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of version 2 of the GNU General Public License
-+ * as published by the Free Software Foundation.
-+ *
-+ * The MFGPTs are documented in AMD Geode CS5536 Companion Device Data Book.
-+ */
-+
-+/*
-+ * We are using the 32Khz input clock - its the only one that has the
-+ * ranges we find desirable. The following table lists the suitable
-+ * divisors and the associated hz, minimum interval
-+ * and the maximum interval:
-+ *
-+ * Divisor Hz Min Delta (S) Max Delta (S)
-+ * 1 32000 .0005 2.048
-+ * 2 16000 .001 4.096
-+ * 4 8000 .002 8.192
-+ * 8 4000 .004 16.384
-+ * 16 2000 .008 32.768
-+ * 32 1000 .016 65.536
-+ * 64 500 .032 131.072
-+ * 128 250 .064 262.144
-+ * 256 125 .128 524.288
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/interrupt.h>
-+#include <linux/module.h>
-+#include <asm/geode.h>
-+
-+#define F_AVAIL 0x01
-+
-+static struct mfgpt_timer_t {
-+ int flags;
-+ struct module *owner;
-+} mfgpt_timers[MFGPT_MAX_TIMERS];
-+
-+/* Selected from the table above */
-+
-+#define MFGPT_DIVISOR 16
-+#define MFGPT_SCALE 4 /* divisor = 2^(scale) */
-+#define MFGPT_HZ (32000 / MFGPT_DIVISOR)
-+#define MFGPT_PERIODIC (MFGPT_HZ / HZ)
-+
-+/* Allow for disabling of MFGPTs */
-+static int disable;
-+static int __init mfgpt_disable(char *s)
-+{
-+ disable = 1;
-+ return 1;
-+}
-+__setup("nomfgpt", mfgpt_disable);
-+
-+/*
-+ * Check whether any MFGPTs are available for the kernel to use. In most
-+ * cases, firmware that uses AMD's VSA code will claim all timers during
-+ * bootup; we certainly don't want to take them if they're already in use.
-+ * In other cases (such as with VSAless OpenFirmware), the system firmware
-+ * leaves timers available for us to use.
-+ */
-+int __init geode_mfgpt_detect(void)
-+{
-+ int count = 0, i;
-+ u16 val;
-+
-+ if (disable) {
-+ printk(KERN_INFO "geode-mfgpt: Skipping MFGPT setup\n");
-+ return 0;
-+ }
-+
-+ for (i = 0; i < MFGPT_MAX_TIMERS; i++) {
-+ val = geode_mfgpt_read(i, MFGPT_REG_SETUP);
-+ if (!(val & MFGPT_SETUP_SETUP)) {
-+ mfgpt_timers[i].flags = F_AVAIL;
-+ count++;
-+ }
-+ }
-+
-+ return count;
-+}
-+
-+int geode_mfgpt_toggle_event(int timer, int cmp, int event, int enable)
-+{
-+ u32 msr, mask, value, dummy;
-+ int shift = (cmp == MFGPT_CMP1) ? 0 : 8;
-+
-+ if (timer < 0 || timer >= MFGPT_MAX_TIMERS)
-+ return -EIO;
-+
-+ /*
-+ * The register maps for these are described in sections 6.17.1.x of
-+ * the AMD Geode CS5536 Companion Device Data Book.
-+ */
-+ switch (event) {
-+ case MFGPT_EVENT_RESET:
-+ /*
-+ * XXX: According to the docs, we cannot reset timers above
-+ * 6; that is, resets for 7 and 8 will be ignored. Is this
-+ * a problem? -dilinger
-+ */
-+ msr = MFGPT_NR_MSR;
-+ mask = 1 << (timer + 24);
-+ break;
-+
-+ case MFGPT_EVENT_NMI:
-+ msr = MFGPT_NR_MSR;
-+ mask = 1 << (timer + shift);
-+ break;
-+
-+ case MFGPT_EVENT_IRQ:
-+ msr = MFGPT_IRQ_MSR;
-+ mask = 1 << (timer + shift);
-+ break;
-+
-+ default:
-+ return -EIO;
-+ }
-+
-+ rdmsr(msr, value, dummy);
-+
-+ if (enable)
-+ value |= mask;
-+ else
-+ value &= ~mask;
-+
-+ wrmsr(msr, value, dummy);
-+ return 0;
-+}
-+EXPORT_SYMBOL(geode_mfgpt_toggle_event);
-+
-+int geode_mfgpt_set_irq(int timer, int cmp, int irq, int enable)
-+{
-+ u32 val, dummy;
-+ int offset;
-+
-+ if (timer < 0 || timer >= MFGPT_MAX_TIMERS)
-+ return -EIO;
-+
-+ if (geode_mfgpt_toggle_event(timer, cmp, MFGPT_EVENT_IRQ, enable))
-+ return -EIO;
-+
-+ rdmsr(0x51400022, val, dummy);
-+
-+ offset = (timer % 4) * 4;
-+
-+ val &= ~((0xF << offset) | (0xF << (offset + 16)));
-+
-+ if (enable) {
-+ val |= (irq & 0x0F) << (offset);
-+ val |= (irq & 0x0F) << (offset + 16);
-+ }
-+
-+ wrmsr(0x51400022, val, dummy);
-+ return 0;
-+}
-+EXPORT_SYMBOL(geode_mfgpt_set_irq);
-+
-+static int mfgpt_get(int timer, struct module *owner)
-+{
-+ mfgpt_timers[timer].flags &= ~F_AVAIL;
-+ mfgpt_timers[timer].owner = owner;
-+ printk(KERN_INFO "geode-mfgpt: Registered timer %d\n", timer);
-+ return timer;
-+}
-+
-+int geode_mfgpt_alloc_timer(int timer, int domain, struct module *owner)
-+{
-+ int i;
-+
-+ if (!geode_get_dev_base(GEODE_DEV_MFGPT))
-+ return -ENODEV;
-+ if (timer >= MFGPT_MAX_TIMERS)
-+ return -EIO;
-+
-+ if (timer < 0) {
-+ /* Try to find an available timer */
-+ for (i = 0; i < MFGPT_MAX_TIMERS; i++) {
-+ if (mfgpt_timers[i].flags & F_AVAIL)
-+ return mfgpt_get(i, owner);
-+
-+ if (i == 5 && domain == MFGPT_DOMAIN_WORKING)
-+ break;
-+ }
-+ } else {
-+ /* If they requested a specific timer, try to honor that */
-+ if (mfgpt_timers[timer].flags & F_AVAIL)
-+ return mfgpt_get(timer, owner);
-+ }
-+
-+ /* No timers available - too bad */
-+ return -1;
-+}
-+EXPORT_SYMBOL(geode_mfgpt_alloc_timer);
---- linux-2.6.22.orig/include/asm-i386/geode.h
-+++ linux-2.6.22/include/asm-i386/geode.h
-@@ -156,4 +156,54 @@
- return (is_geode_gx() || is_geode_lx());
- }
-
-+/* MFGPTs */
-+
-+#define MFGPT_MAX_TIMERS 8
-+#define MFGPT_TIMER_ANY -1
-+
-+#define MFGPT_DOMAIN_WORKING 1
-+#define MFGPT_DOMAIN_STANDBY 2
-+#define MFGPT_DOMAIN_ANY (MFGPT_DOMAIN_WORKING | MFGPT_DOMAIN_STANDBY)
-+
-+#define MFGPT_CMP1 0
-+#define MFGPT_CMP2 1
-+
-+#define MFGPT_EVENT_IRQ 0
-+#define MFGPT_EVENT_NMI 1
-+#define MFGPT_EVENT_RESET 3
-+
-+#define MFGPT_REG_CMP1 0
-+#define MFGPT_REG_CMP2 2
-+#define MFGPT_REG_COUNTER 4
-+#define MFGPT_REG_SETUP 6
-+
-+#define MFGPT_SETUP_CNTEN (1 << 15)
-+#define MFGPT_SETUP_CMP2 (1 << 14)
-+#define MFGPT_SETUP_CMP1 (1 << 13)
-+#define MFGPT_SETUP_SETUP (1 << 12)
-+#define MFGPT_SETUP_STOPEN (1 << 11)
-+#define MFGPT_SETUP_EXTEN (1 << 10)
-+#define MFGPT_SETUP_REVEN (1 << 5)
-+#define MFGPT_SETUP_CLKSEL (1 << 4)
-+
-+static inline void geode_mfgpt_write(int timer, u16 reg, u16 value)
-+{
-+ u32 base = geode_get_dev_base(GEODE_DEV_MFGPT);
-+ outw(value, base + reg + (timer * 8));
-+}
-+
-+static inline u16 geode_mfgpt_read(int timer, u16 reg)
-+{
-+ u32 base = geode_get_dev_base(GEODE_DEV_MFGPT);
-+ return inw(base + reg + (timer * 8));
-+}
-+
-+extern int __init geode_mfgpt_detect(void);
-+extern int geode_mfgpt_toggle_event(int timer, int cmp, int event, int enable);
-+extern int geode_mfgpt_set_irq(int timer, int cmp, int irq, int enable);
-+extern int geode_mfgpt_alloc_timer(int timer, int domain, struct module *owner);
-+
-+#define geode_mfgpt_setup_irq(t, c, i) geode_mfgpt_set_irq((t), (c), (i), 1)
-+#define geode_mfgpt_release_irq(t, c, i) geode_mfgpt_set_irq((t), (c), (i), 0)
-+
- #endif
diff --git a/recipes/linux/linux/alix/defconfig b/recipes/linux/linux/geodelx/defconfig
similarity index 57%
rename from recipes/linux/linux/alix/defconfig
rename to recipes/linux/linux/geodelx/defconfig
index 9cffb88..1749011 100644
--- a/recipes/linux/linux/alix/defconfig
+++ b/recipes/linux/linux/geodelx/defconfig
@@ -1,9 +1,13 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc3
-# Mon Aug 27 14:49:39 2007
+# Linux kernel version: 2.6.29
+# Tue May 5 17:55:26 2009
#
+# CONFIG_64BIT is not set
CONFIG_X86_32=y
+# CONFIG_X86_64 is not set
+CONFIG_X86=y
+CONFIG_ARCH_DEFCONFIG="arch/x86/configs/i386_defconfig"
CONFIG_GENERIC_TIME=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_CLOCKSOURCE_WATCHDOG=y
@@ -11,17 +15,36 @@ CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
CONFIG_LOCKDEP_SUPPORT=y
CONFIG_STACKTRACE_SUPPORT=y
-CONFIG_SEMAPHORE_SLEEPERS=y
-CONFIG_X86=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_FAST_CMPXCHG_LOCAL=y
CONFIG_MMU=y
CONFIG_ZONE_DMA=y
-CONFIG_QUICKLIST=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_IOMAP=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_GPIO=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
-CONFIG_DMI=y
+# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
+CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+# CONFIG_GENERIC_TIME_VSYSCALL is not set
+CONFIG_ARCH_HAS_CPU_RELAX=y
+CONFIG_ARCH_HAS_DEFAULT_IDLE=y
+CONFIG_ARCH_HAS_CACHE_LINE_SIZE=y
+# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
+# CONFIG_HAVE_CPUMASK_OF_CPU_MAP is not set
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+# CONFIG_ZONE_DMA32 is not set
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+# CONFIG_AUDIT_ARCH is not set
+CONFIG_ARCH_SUPPORTS_OPTIMIZED_INLINING=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_X86_BIOS_REBOOT=y
+CONFIG_KTIME_SCALAR=y
CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
@@ -40,16 +63,36 @@ CONFIG_POSIX_MQUEUE=y
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
CONFIG_AUDIT=y
# CONFIG_AUDITSYSCALL is not set
-# CONFIG_IKCONFIG is not set
+
+#
+# RCU Subsystem
+#
+# CONFIG_CLASSIC_RCU is not set
+# CONFIG_TREE_RCU is not set
+CONFIG_PREEMPT_RCU=y
+# CONFIG_RCU_TRACE is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_SYSFS_DEPRECATED is not set
+CONFIG_HAVE_UNSTABLE_SCHED_CLOCK=y
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
# CONFIG_RELAY is not set
+CONFIG_NAMESPACES=y
+# CONFIG_UTS_NS is not set
+# CONFIG_IPC_NS is not set
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
# CONFIG_BLK_DEV_INITRD is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
# CONFIG_EMBEDDED is not set
CONFIG_UID16=y
CONFIG_SYSCTL_SYSCALL=y
@@ -60,32 +103,47 @@ CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_PCSPKR_PLATFORM=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
-CONFIG_ANON_INODES=y
CONFIG_EPOLL=y
CONFIG_SIGNALFD=y
CONFIG_TIMERFD=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
+CONFIG_AIO=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_PCI_QUIRKS=y
+# CONFIG_COMPAT_BRK is not set
CONFIG_SLAB=y
# CONFIG_SLUB is not set
# CONFIG_SLOB is not set
+CONFIG_PROFILING=y
+CONFIG_TRACEPOINTS=y
+# CONFIG_MARKERS is not set
+CONFIG_OPROFILE=m
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
+CONFIG_HAVE_IOREMAP_PROT=y
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
-# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
CONFIG_MODVERSIONS=y
# CONFIG_MODULE_SRCVERSION_ALL is not set
-CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
-# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
@@ -99,6 +157,7 @@ CONFIG_IOSCHED_CFQ=y
CONFIG_DEFAULT_CFQ=y
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="cfq"
+CONFIG_FREEZER=y
#
# Processor type and features
@@ -106,17 +165,18 @@ CONFIG_DEFAULT_IOSCHED="cfq"
CONFIG_TICK_ONESHOT=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
# CONFIG_SMP is not set
+# CONFIG_X86_MPPARSE is not set
CONFIG_X86_PC=y
# CONFIG_X86_ELAN is not set
# CONFIG_X86_VOYAGER is not set
-# CONFIG_X86_NUMAQ is not set
-# CONFIG_X86_SUMMIT is not set
-# CONFIG_X86_BIGSMP is not set
-# CONFIG_X86_VISWS is not set
# CONFIG_X86_GENERICARCH is not set
-# CONFIG_X86_ES7000 is not set
-# CONFIG_PARAVIRT is not set
+# CONFIG_X86_VSMP is not set
+# CONFIG_X86_RDC321X is not set
+CONFIG_SCHED_OMIT_FRAME_POINTER=y
+# CONFIG_PARAVIRT_GUEST is not set
+# CONFIG_MEMTEST is not set
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
@@ -126,7 +186,6 @@ CONFIG_X86_PC=y
# CONFIG_MPENTIUMII is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUMM is not set
-# CONFIG_MCORE2 is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
@@ -134,21 +193,20 @@ CONFIG_X86_PC=y
# CONFIG_MCRUSOE is not set
# CONFIG_MEFFICEON is not set
# CONFIG_MWINCHIPC6 is not set
-# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MGEODEGX1 is not set
CONFIG_MGEODE_LX=y
# CONFIG_MCYRIXIII is not set
# CONFIG_MVIAC3_2 is not set
# CONFIG_MVIAC7 is not set
+# CONFIG_MPSC is not set
+# CONFIG_MCORE2 is not set
+# CONFIG_GENERIC_CPU is not set
# CONFIG_X86_GENERIC is not set
+CONFIG_X86_CPU=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_X86_XADD=y
-CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-# CONFIG_ARCH_HAS_ILOG2_U32 is not set
-# CONFIG_ARCH_HAS_ILOG2_U64 is not set
-CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_BSWAP=y
@@ -157,16 +215,29 @@ CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_TSC=y
CONFIG_X86_MINIMUM_CPU_FAMILY=4
+CONFIG_X86_DEBUGCTLMSR=y
+CONFIG_CPU_SUP_INTEL=y
+CONFIG_CPU_SUP_CYRIX_32=y
+CONFIG_CPU_SUP_AMD=y
+CONFIG_CPU_SUP_CENTAUR_32=y
+CONFIG_CPU_SUP_TRANSMETA_32=y
+CONFIG_CPU_SUP_UMC_32=y
+CONFIG_X86_DS=y
+CONFIG_X86_PTRACE_BTS=y
CONFIG_HPET_TIMER=y
CONFIG_HPET_EMULATE_RTC=y
+CONFIG_DMI=y
+# CONFIG_IOMMU_HELPER is not set
+# CONFIG_IOMMU_API is not set
+CONFIG_NR_CPUS=1
# CONFIG_PREEMPT_NONE is not set
# CONFIG_PREEMPT_VOLUNTARY is not set
CONFIG_PREEMPT=y
-CONFIG_PREEMPT_BKL=y
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
+# CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS is not set
# CONFIG_X86_MCE is not set
CONFIG_VM86=y
# CONFIG_TOSHIBA is not set
@@ -175,23 +246,15 @@ CONFIG_X86_REBOOTFIXUPS=y
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=m
# CONFIG_X86_CPUID is not set
-
-#
-# Firmware Drivers
-#
-# CONFIG_EDD is not set
-# CONFIG_DELL_RBU is not set
-# CONFIG_DCDBAS is not set
-# CONFIG_DMIID is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
CONFIG_PAGE_OFFSET=0xC0000000
# CONFIG_X86_PAE is not set
+# CONFIG_ARCH_PHYS_ADDR_T_64BIT is not set
CONFIG_ARCH_FLATMEM_ENABLE=y
CONFIG_ARCH_SPARSEMEM_ENABLE=y
CONFIG_ARCH_SELECT_MEMORY_MODEL=y
-CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
@@ -199,12 +262,16 @@ CONFIG_FLATMEM_MANUAL=y
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_SPARSEMEM_STATIC=y
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
-# CONFIG_RESOURCES_64BIT is not set
+# CONFIG_PHYS_ADDR_T_64BIT is not set
CONFIG_ZONE_DMA_FLAG=1
CONFIG_BOUNCE=y
-CONFIG_NR_QUICK=1
CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_X86_CHECK_BIOS_CORRUPTION=y
+CONFIG_X86_BOOTPARAM_MEMORY_CORRUPTION_CHECK=y
+# CONFIG_X86_RESERVE_LOW_64K is not set
# CONFIG_MATH_EMULATION is not set
# CONFIG_MTRR is not set
# CONFIG_EFI is not set
@@ -214,121 +281,191 @@ CONFIG_SECCOMP=y
# CONFIG_HZ_300 is not set
CONFIG_HZ_1000=y
CONFIG_HZ=1000
+CONFIG_SCHED_HRTICK=y
# CONFIG_KEXEC is not set
CONFIG_PHYSICAL_START=0x100000
# CONFIG_RELOCATABLE is not set
CONFIG_PHYSICAL_ALIGN=0x100000
# CONFIG_COMPAT_VDSO is not set
+# CONFIG_CMDLINE_BOOL is not set
#
-# Power management options (ACPI, APM)
+# Power management and ACPI options
#
CONFIG_PM=y
-# CONFIG_PM_LEGACY is not set
# CONFIG_PM_DEBUG is not set
-# CONFIG_SUSPEND is not set
-# CONFIG_HIBERNATION is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_HIBERNATION=y
+CONFIG_PM_STD_PARTITION=""
CONFIG_ACPI=y
+CONFIG_ACPI_SLEEP=y
# CONFIG_ACPI_PROCFS is not set
-# CONFIG_ACPI_AC is not set
+# CONFIG_ACPI_PROCFS_POWER is not set
+CONFIG_ACPI_SYSFS_POWER=y
+# CONFIG_ACPI_PROC_EVENT is not set
+CONFIG_ACPI_AC=m
# CONFIG_ACPI_BATTERY is not set
-# CONFIG_ACPI_BUTTON is not set
+CONFIG_ACPI_BUTTON=m
# CONFIG_ACPI_FAN is not set
-# CONFIG_ACPI_DOCK is not set
-# CONFIG_ACPI_PROCESSOR is not set
-# CONFIG_ACPI_ASUS is not set
-# CONFIG_ACPI_TOSHIBA is not set
+CONFIG_ACPI_DOCK=y
+CONFIG_ACPI_PROCESSOR=m
+CONFIG_ACPI_THERMAL=m
+# CONFIG_ACPI_CUSTOM_DSDT is not set
CONFIG_ACPI_BLACKLIST_YEAR=0
# CONFIG_ACPI_DEBUG is not set
-CONFIG_ACPI_EC=y
-CONFIG_ACPI_POWER=y
-CONFIG_ACPI_SYSTEM=y
+# CONFIG_ACPI_PCI_SLOT is not set
CONFIG_X86_PM_TIMER=y
# CONFIG_ACPI_CONTAINER is not set
# CONFIG_ACPI_SBS is not set
+# CONFIG_APM is not set
#
# CPU Frequency scaling
#
# CONFIG_CPU_FREQ is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_USERSPACE is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND is not set
+# CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE is not set
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+CONFIG_CPU_IDLE_GOV_MENU=y
#
-# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
+# Bus options (PCI etc.)
#
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GOMMCONFIG is not set
# CONFIG_PCI_GODIRECT is not set
+# CONFIG_PCI_GOOLPC is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_MMCONFIG=y
+CONFIG_PCI_OLPC=y
+CONFIG_PCI_DOMAINS=y
# CONFIG_PCIEPORTBUS is not set
CONFIG_ARCH_SUPPORTS_MSI=y
# CONFIG_PCI_MSI is not set
+# CONFIG_PCI_LEGACY is not set
# CONFIG_PCI_DEBUG is not set
+# CONFIG_PCI_STUB is not set
# CONFIG_HT_IRQ is not set
CONFIG_ISA_DMA_API=y
# CONFIG_ISA is not set
# CONFIG_MCA is not set
-# CONFIG_SCx200 is not set
+CONFIG_SCx200=m
+CONFIG_SCx200HR_TIMER=m
CONFIG_GEODE_MFGPT_TIMER=y
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
+CONFIG_OLPC=y
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
#
-# Executable file formats
+# Executable file formats / Emulations
#
CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
# CONFIG_BINFMT_AOUT is not set
CONFIG_BINFMT_MISC=m
-
-#
-# Networking
-#
+CONFIG_HAVE_ATOMIC_IOMAP=y
CONFIG_NET=y
#
# Networking options
#
+CONFIG_COMPAT_NET_DEV_OPS=y
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_XFRM_IPCOMP=m
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
-# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_ASK_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
CONFIG_IP_FIB_HASH=y
-# CONFIG_IP_PNP is not set
+# CONFIG_IP_MULTIPLE_TABLES is not set
+# CONFIG_IP_ROUTE_MULTIPATH is not set
+# CONFIG_IP_ROUTE_VERBOSE is not set
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_ARPD is not set
CONFIG_SYN_COOKIES=y
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_INET_XFRM_TUNNEL is not set
-# CONFIG_INET_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_CUBIC=y
-CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_TCP_MD5SIG is not set
-# CONFIG_IP_VS is not set
-# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
+CONFIG_INET_AH=m
+CONFIG_INET_ESP=m
+CONFIG_INET_IPCOMP=m
+CONFIG_INET_XFRM_TUNNEL=m
+CONFIG_INET_TUNNEL=m
+CONFIG_INET_XFRM_MODE_TRANSPORT=m
+CONFIG_INET_XFRM_MODE_TUNNEL=m
+CONFIG_INET_XFRM_MODE_BEET=m
+CONFIG_INET_LRO=m
+CONFIG_INET_DIAG=m
+CONFIG_INET_TCP_DIAG=m
+CONFIG_TCP_CONG_ADVANCED=y
+CONFIG_TCP_CONG_BIC=m
+CONFIG_TCP_CONG_CUBIC=m
+CONFIG_TCP_CONG_WESTWOOD=m
+CONFIG_TCP_CONG_HTCP=m
+CONFIG_TCP_CONG_HSTCP=m
+CONFIG_TCP_CONG_HYBLA=m
+CONFIG_TCP_CONG_VEGAS=m
+CONFIG_TCP_CONG_SCALABLE=m
+CONFIG_TCP_CONG_LP=m
+CONFIG_TCP_CONG_VENO=m
+CONFIG_TCP_CONG_YEAH=m
+CONFIG_TCP_CONG_ILLINOIS=m
+# CONFIG_DEFAULT_BIC is not set
+# CONFIG_DEFAULT_CUBIC is not set
+# CONFIG_DEFAULT_HTCP is not set
+# CONFIG_DEFAULT_VEGAS is not set
+# CONFIG_DEFAULT_WESTWOOD is not set
+CONFIG_DEFAULT_RENO=y
+CONFIG_DEFAULT_TCP_CONG="reno"
+CONFIG_TCP_MD5SIG=y
+CONFIG_IPV6=m
+CONFIG_IPV6_PRIVACY=y
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
+CONFIG_INET6_AH=m
+CONFIG_INET6_ESP=m
+CONFIG_INET6_IPCOMP=m
+CONFIG_IPV6_MIP6=m
+CONFIG_INET6_XFRM_TUNNEL=m
+CONFIG_INET6_TUNNEL=m
+CONFIG_INET6_XFRM_MODE_TRANSPORT=m
+CONFIG_INET6_XFRM_MODE_TUNNEL=m
+CONFIG_INET6_XFRM_MODE_BEET=m
+CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
+CONFIG_IPV6_SIT=m
+CONFIG_IPV6_NDISC_NODETYPE=y
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IPV6_MULTIPLE_TABLES=y
+CONFIG_IPV6_SUBTREES=y
+CONFIG_IPV6_MROUTE=y
+CONFIG_IPV6_PIMSM_V2=y
# CONFIG_NETWORK_SECMARK is not set
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
CONFIG_BRIDGE_NETFILTER=y
#
@@ -337,11 +474,11 @@ CONFIG_BRIDGE_NETFILTER=y
CONFIG_NETFILTER_NETLINK=m
CONFIG_NETFILTER_NETLINK_QUEUE=m
CONFIG_NETFILTER_NETLINK_LOG=m
-CONFIG_NF_CONNTRACK_ENABLED=m
CONFIG_NF_CONNTRACK=m
CONFIG_NF_CT_ACCT=y
CONFIG_NF_CONNTRACK_MARK=y
CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NF_CT_PROTO_DCCP=m
CONFIG_NF_CT_PROTO_GRE=m
CONFIG_NF_CT_PROTO_SCTP=m
CONFIG_NF_CT_PROTO_UDPLITE=m
@@ -355,16 +492,20 @@ CONFIG_NF_CONNTRACK_SANE=m
CONFIG_NF_CONNTRACK_SIP=m
CONFIG_NF_CONNTRACK_TFTP=m
CONFIG_NF_CT_NETLINK=m
+CONFIG_NETFILTER_TPROXY=m
CONFIG_NETFILTER_XTABLES=m
CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
-# CONFIG_NETFILTER_XT_TARGET_CONNMARK is not set
-# CONFIG_NETFILTER_XT_TARGET_DSCP is not set
+CONFIG_NETFILTER_XT_TARGET_CONNMARK=m
+CONFIG_NETFILTER_XT_TARGET_DSCP=m
CONFIG_NETFILTER_XT_TARGET_MARK=m
-CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
CONFIG_NETFILTER_XT_TARGET_NFLOG=m
-# CONFIG_NETFILTER_XT_TARGET_NOTRACK is not set
-# CONFIG_NETFILTER_XT_TARGET_TRACE is not set
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NOTRACK=m
+CONFIG_NETFILTER_XT_TARGET_RATEEST=m
+CONFIG_NETFILTER_XT_TARGET_TPROXY=m
+CONFIG_NETFILTER_XT_TARGET_TRACE=m
CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
+CONFIG_NETFILTER_XT_TARGET_TCPOPTSTRIP=m
CONFIG_NETFILTER_XT_MATCH_COMMENT=m
CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
@@ -373,39 +514,45 @@ CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
CONFIG_NETFILTER_XT_MATCH_DCCP=m
CONFIG_NETFILTER_XT_MATCH_DSCP=m
CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
CONFIG_NETFILTER_XT_MATCH_HELPER=m
+CONFIG_NETFILTER_XT_MATCH_IPRANGE=m
CONFIG_NETFILTER_XT_MATCH_LENGTH=m
CONFIG_NETFILTER_XT_MATCH_LIMIT=m
CONFIG_NETFILTER_XT_MATCH_MAC=m
CONFIG_NETFILTER_XT_MATCH_MARK=m
CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
-# CONFIG_NETFILTER_XT_MATCH_PHYSDEV is not set
+CONFIG_NETFILTER_XT_MATCH_OWNER=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_PHYSDEV=m
CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_RATEEST=m
CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_RECENT=m
+# CONFIG_NETFILTER_XT_MATCH_RECENT_PROC_COMPAT is not set
CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_SOCKET=m
CONFIG_NETFILTER_XT_MATCH_STATE=m
CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
CONFIG_NETFILTER_XT_MATCH_STRING=m
CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_TIME=m
CONFIG_NETFILTER_XT_MATCH_U32=m
-CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
+# CONFIG_IP_VS is not set
#
# IP: Netfilter Configuration
#
+CONFIG_NF_DEFRAG_IPV4=m
CONFIG_NF_CONNTRACK_IPV4=m
CONFIG_NF_CONNTRACK_PROC_COMPAT=y
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_IPRANGE=m
-CONFIG_IP_NF_MATCH_TOS=m
-CONFIG_IP_NF_MATCH_RECENT=m
-CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_ECN=m
CONFIG_IP_NF_MATCH_TTL=m
-CONFIG_IP_NF_MATCH_OWNER=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_LOG=m
@@ -413,11 +560,13 @@ CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_NF_NAT=m
CONFIG_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
-CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_TARGET_NETMAP=m
-CONFIG_IP_NF_TARGET_SAME=m
+CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_NF_NAT_SNMP_BASIC=m
+CONFIG_NF_NAT_PROTO_DCCP=m
CONFIG_NF_NAT_PROTO_GRE=m
+CONFIG_NF_NAT_PROTO_UDPLITE=m
+CONFIG_NF_NAT_PROTO_SCTP=m
CONFIG_NF_NAT_FTP=m
CONFIG_NF_NAT_IRC=m
CONFIG_NF_NAT_TFTP=m
@@ -426,24 +575,63 @@ CONFIG_NF_NAT_PPTP=m
CONFIG_NF_NAT_H323=m
CONFIG_NF_NAT_SIP=m
CONFIG_IP_NF_MANGLE=m
-CONFIG_IP_NF_TARGET_TOS=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_TTL=m
-CONFIG_IP_NF_TARGET_CLUSTERIP=m
CONFIG_IP_NF_RAW=m
CONFIG_IP_NF_ARPTABLES=m
CONFIG_IP_NF_ARPFILTER=m
CONFIG_IP_NF_ARP_MANGLE=m
#
-# Bridge: Netfilter Configuration
-#
-# CONFIG_BRIDGE_NF_EBTABLES is not set
+# IPv6: Netfilter Configuration
+#
+CONFIG_NF_CONNTRACK_IPV6=m
+CONFIG_IP6_NF_QUEUE=m
+CONFIG_IP6_NF_IPTABLES=m
+CONFIG_IP6_NF_MATCH_AH=m
+CONFIG_IP6_NF_MATCH_EUI64=m
+CONFIG_IP6_NF_MATCH_FRAG=m
+CONFIG_IP6_NF_MATCH_OPTS=m
+CONFIG_IP6_NF_MATCH_HL=m
+CONFIG_IP6_NF_MATCH_IPV6HEADER=m
+CONFIG_IP6_NF_MATCH_MH=m
+CONFIG_IP6_NF_MATCH_RT=m
+CONFIG_IP6_NF_TARGET_LOG=m
+CONFIG_IP6_NF_FILTER=m
+CONFIG_IP6_NF_TARGET_REJECT=m
+CONFIG_IP6_NF_MANGLE=m
+CONFIG_IP6_NF_TARGET_HL=m
+CONFIG_IP6_NF_RAW=m
+CONFIG_BRIDGE_NF_EBTABLES=m
+CONFIG_BRIDGE_EBT_BROUTE=m
+CONFIG_BRIDGE_EBT_T_FILTER=m
+CONFIG_BRIDGE_EBT_T_NAT=m
+CONFIG_BRIDGE_EBT_802_3=m
+CONFIG_BRIDGE_EBT_AMONG=m
+CONFIG_BRIDGE_EBT_ARP=m
+CONFIG_BRIDGE_EBT_IP=m
+CONFIG_BRIDGE_EBT_IP6=m
+CONFIG_BRIDGE_EBT_LIMIT=m
+CONFIG_BRIDGE_EBT_MARK=m
+CONFIG_BRIDGE_EBT_PKTTYPE=m
+CONFIG_BRIDGE_EBT_STP=m
+CONFIG_BRIDGE_EBT_VLAN=m
+CONFIG_BRIDGE_EBT_ARPREPLY=m
+CONFIG_BRIDGE_EBT_DNAT=m
+CONFIG_BRIDGE_EBT_MARK_T=m
+CONFIG_BRIDGE_EBT_REDIRECT=m
+CONFIG_BRIDGE_EBT_SNAT=m
+CONFIG_BRIDGE_EBT_LOG=m
+CONFIG_BRIDGE_EBT_ULOG=m
+CONFIG_BRIDGE_EBT_NFLOG=m
# CONFIG_IP_DCCP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_TIPC is not set
# CONFIG_ATM is not set
+CONFIG_STP=m
CONFIG_BRIDGE=m
+# CONFIG_NET_DSA is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
CONFIG_LLC=m
@@ -454,19 +642,68 @@ CONFIG_LLC=m
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
+CONFIG_NET_SCHED=y
#
-# QoS and/or fair queueing
+# Queueing/Scheduling
#
-# CONFIG_NET_SCHED is not set
-CONFIG_NET_SCH_FIFO=y
+CONFIG_NET_SCH_CBQ=m
+CONFIG_NET_SCH_HTB=m
+CONFIG_NET_SCH_HFSC=m
+CONFIG_NET_SCH_PRIO=m
+CONFIG_NET_SCH_MULTIQ=m
+CONFIG_NET_SCH_RED=m
+CONFIG_NET_SCH_SFQ=m
+CONFIG_NET_SCH_TEQL=m
+CONFIG_NET_SCH_TBF=m
+CONFIG_NET_SCH_GRED=m
+CONFIG_NET_SCH_DSMARK=m
+CONFIG_NET_SCH_NETEM=m
+CONFIG_NET_SCH_DRR=m
+# CONFIG_NET_SCH_INGRESS is not set
+
+#
+# Classification
+#
+CONFIG_NET_CLS=y
+CONFIG_NET_CLS_BASIC=m
+CONFIG_NET_CLS_TCINDEX=m
+CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
+CONFIG_NET_CLS_FW=m
+CONFIG_NET_CLS_U32=m
+CONFIG_CLS_U32_PERF=y
+CONFIG_CLS_U32_MARK=y
+CONFIG_NET_CLS_RSVP=m
+CONFIG_NET_CLS_RSVP6=m
+CONFIG_NET_CLS_FLOW=m
+CONFIG_NET_EMATCH=y
+CONFIG_NET_EMATCH_STACK=32
+CONFIG_NET_EMATCH_CMP=m
+CONFIG_NET_EMATCH_NBYTE=m
+CONFIG_NET_EMATCH_U32=m
+CONFIG_NET_EMATCH_META=m
+CONFIG_NET_EMATCH_TEXT=m
+CONFIG_NET_CLS_ACT=y
+CONFIG_NET_ACT_POLICE=m
+CONFIG_NET_ACT_GACT=m
+CONFIG_GACT_PROB=y
+CONFIG_NET_ACT_MIRRED=m
+CONFIG_NET_ACT_IPT=m
+CONFIG_NET_ACT_NAT=m
+CONFIG_NET_ACT_PEDIT=m
+CONFIG_NET_ACT_SIMP=m
+CONFIG_NET_ACT_SKBEDIT=m
+CONFIG_NET_CLS_IND=y
+CONFIG_NET_SCH_FIFO=y
+# CONFIG_DCB is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
CONFIG_BT=m
CONFIG_BT_L2CAP=m
@@ -481,30 +718,47 @@ CONFIG_BT_HIDP=m
#
# Bluetooth device drivers
#
-CONFIG_BT_HCIUSB=m
-CONFIG_BT_HCIUSB_SCO=y
-# CONFIG_BT_HCIUART is not set
-# CONFIG_BT_HCIBCM203X is not set
-# CONFIG_BT_HCIBPA10X is not set
-# CONFIG_BT_HCIBFUSB is not set
+CONFIG_BT_HCIBTUSB=m
+CONFIG_BT_HCIUART=m
+CONFIG_BT_HCIUART_H4=y
+CONFIG_BT_HCIUART_BCSP=y
+CONFIG_BT_HCIUART_LL=y
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
# CONFIG_BT_HCIVHCI is not set
# CONFIG_AF_RXRPC is not set
-
-#
-# Wireless
-#
+# CONFIG_PHONET is not set
+CONFIG_FIB_RULES=y
+CONFIG_WIRELESS=y
CONFIG_CFG80211=m
+# CONFIG_CFG80211_REG_DEBUG is not set
+CONFIG_NL80211=y
+CONFIG_WIRELESS_OLD_REGULATORY=y
CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
+CONFIG_LIB80211=m
+CONFIG_LIB80211_CRYPT_WEP=m
+CONFIG_LIB80211_CRYPT_CCMP=m
+CONFIG_LIB80211_CRYPT_TKIP=m
+# CONFIG_LIB80211_DEBUG is not set
CONFIG_MAC80211=m
-# CONFIG_MAC80211_DEBUG is not set
-CONFIG_IEEE80211=m
-# CONFIG_IEEE80211_DEBUG is not set
-CONFIG_IEEE80211_CRYPT_WEP=m
-CONFIG_IEEE80211_CRYPT_CCMP=m
-CONFIG_IEEE80211_CRYPT_TKIP=m
-CONFIG_IEEE80211_SOFTMAC=m
-# CONFIG_IEEE80211_SOFTMAC_DEBUG is not set
-# CONFIG_RFKILL is not set
+
+#
+# Rate control algorithm selection
+#
+CONFIG_MAC80211_RC_MINSTREL=y
+# CONFIG_MAC80211_RC_DEFAULT_PID is not set
+CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
+CONFIG_MAC80211_RC_DEFAULT="minstrel"
+CONFIG_MAC80211_MESH=y
+CONFIG_MAC80211_LEDS=y
+# CONFIG_MAC80211_DEBUGFS is not set
+# CONFIG_MAC80211_DEBUG_MENU is not set
+# CONFIG_WIMAX is not set
+CONFIG_RFKILL=y
+CONFIG_RFKILL_INPUT=m
+CONFIG_RFKILL_LEDS=y
# CONFIG_NET_9P is not set
#
@@ -514,9 +768,12 @@ CONFIG_IEEE80211_SOFTMAC=m
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
-CONFIG_FW_LOADER=m
+CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_DEBUG_DEVRES is not set
# CONFIG_SYS_HYPERVISOR is not set
@@ -524,15 +781,14 @@ CONFIG_FW_LOADER=m
# CONFIG_MTD is not set
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
-# CONFIG_PARPORT_SERIAL is not set
-# CONFIG_PARPORT_PC_FIFO is not set
-# CONFIG_PARPORT_PC_SUPERIO is not set
+CONFIG_PARPORT_SERIAL=m
+CONFIG_PARPORT_PC_FIFO=y
+CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_GSC is not set
-CONFIG_PARPORT_AX88796=m
+# CONFIG_PARPORT_AX88796 is not set
CONFIG_PARPORT_1284=y
-CONFIG_PARPORT_NOT_PC=y
CONFIG_PNP=y
-# CONFIG_PNP_DEBUG is not set
+# CONFIG_PNP_DEBUG_MESSAGES is not set
#
# Protocols
@@ -547,14 +803,17 @@ CONFIG_BLK_DEV=y
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=m
-# CONFIG_BLK_DEV_CRYPTOLOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_CRYPTOLOOP=m
+CONFIG_BLK_DEV_NBD=m
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
-# CONFIG_ATA_OVER_ETH is not set
+CONFIG_ATA_OVER_ETH=m
+# CONFIG_BLK_DEV_HD is not set
# CONFIG_MISC_DEVICES is not set
+CONFIG_EEPROM_93CX6=m
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
@@ -571,20 +830,20 @@ CONFIG_SCSI_DMA=y
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
-# CONFIG_CHR_DEV_ST is not set
+CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_CHR_DEV_SG=m
-# CONFIG_CHR_DEV_SCH is not set
+CONFIG_CHR_DEV_SCH=m
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
CONFIG_SCSI_MULTI_LUN=y
-# CONFIG_SCSI_CONSTANTS is not set
+CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
-# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_SCSI_WAIT_SCAN=m
#
@@ -594,11 +853,16 @@ CONFIG_SCSI_WAIT_SCAN=m
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
CONFIG_ATA_ACPI=y
+# CONFIG_SATA_PMP is not set
# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
@@ -608,21 +872,22 @@ CONFIG_ATA_ACPI=y
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
-# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_SATA_VITESSE is not set
# CONFIG_SATA_INIC162X is not set
+# CONFIG_PATA_ACPI is not set
# CONFIG_PATA_ALI is not set
-CONFIG_PATA_AMD=y
+# CONFIG_PATA_AMD is not set
# CONFIG_PATA_ARTOP is not set
# CONFIG_PATA_ATIIXP is not set
# CONFIG_PATA_CMD640_PCI is not set
# CONFIG_PATA_CMD64X is not set
# CONFIG_PATA_CS5520 is not set
# CONFIG_PATA_CS5530 is not set
-# CONFIG_PATA_CS5535 is not set
+CONFIG_PATA_CS5535=y
+CONFIG_PATA_CS5536=y
# CONFIG_PATA_CYPRESS is not set
# CONFIG_PATA_EFAR is not set
# CONFIG_ATA_GENERIC is not set
@@ -638,7 +903,9 @@ CONFIG_PATA_AMD=y
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
@@ -651,30 +918,47 @@ CONFIG_PATA_AMD=y
# CONFIG_PATA_SIS is not set
# CONFIG_PATA_VIA is not set
# CONFIG_PATA_WINBOND is not set
-# CONFIG_MD is not set
+# CONFIG_PATA_SCH is not set
+CONFIG_MD=y
+CONFIG_BLK_DEV_MD=m
+CONFIG_MD_LINEAR=m
+CONFIG_MD_RAID0=m
+CONFIG_MD_RAID1=m
+CONFIG_MD_RAID10=m
+CONFIG_MD_RAID456=m
+CONFIG_MD_RAID5_RESHAPE=y
+CONFIG_MD_MULTIPATH=m
+CONFIG_MD_FAULTY=m
+CONFIG_BLK_DEV_DM=m
+# CONFIG_DM_DEBUG is not set
+CONFIG_DM_CRYPT=m
+CONFIG_DM_SNAPSHOT=m
+CONFIG_DM_MIRROR=m
+CONFIG_DM_ZERO=m
+CONFIG_DM_MULTIPATH=m
+CONFIG_DM_DELAY=m
+# CONFIG_DM_UEVENT is not set
+# CONFIG_FUSION is not set
#
-# Fusion MPT device support
+# IEEE 1394 (FireWire) support
#
-# CONFIG_FUSION is not set
-# CONFIG_FUSION_SPI is not set
-# CONFIG_FUSION_FC is not set
-# CONFIG_FUSION_SAS is not set
#
-# IEEE 1394 (FireWire) support
+# Enable only one of the two stacks, unless you know what you are doing
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
# CONFIG_MACINTOSH_DRIVERS is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
+# CONFIG_IFB is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
-# CONFIG_TUN is not set
+CONFIG_TUN=m
+# CONFIG_VETH is not set
# CONFIG_NET_SB1000 is not set
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
@@ -683,33 +967,79 @@ CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
# CONFIG_CASSINI is not set
-# CONFIG_NET_VENDOR_3COM is not set
-# CONFIG_NET_TULIP is not set
+CONFIG_NET_VENDOR_3COM=y
+CONFIG_VORTEX=m
+CONFIG_TYPHOON=m
+# CONFIG_ENC28J60 is not set
+# CONFIG_DNET is not set
+CONFIG_NET_TULIP=y
+CONFIG_DE2104X=m
+CONFIG_TULIP=m
+CONFIG_TULIP_MWI=y
+CONFIG_TULIP_MMIO=y
+CONFIG_TULIP_NAPI=y
+CONFIG_TULIP_NAPI_HW_MITIGATION=y
+CONFIG_DE4X5=m
+# CONFIG_WINBOND_840 is not set
+# CONFIG_DM9102 is not set
+# CONFIG_ULI526X is not set
# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_AMD8111_ETH is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_B44 is not set
# CONFIG_FORCEDETH is not set
-# CONFIG_DGRS is not set
-# CONFIG_EEPRO100 is not set
-# CONFIG_E100 is not set
+CONFIG_E100=m
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
-# CONFIG_NE2K_PCI is not set
-# CONFIG_8139CP is not set
-# CONFIG_8139TOO is not set
+CONFIG_NE2K_PCI=m
+CONFIG_8139CP=m
+CONFIG_8139TOO=m
+CONFIG_8139TOO_PIO=y
+CONFIG_8139TOO_TUNE_TWISTER=y
+# CONFIG_8139TOO_8129 is not set
+# CONFIG_8139_OLD_RX_RESET is not set
+# CONFIG_R6040 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
+# CONFIG_SMSC9420 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
CONFIG_VIA_RHINE=y
CONFIG_VIA_RHINE_MMIO=y
-CONFIG_VIA_RHINE_NAPI=y
-# CONFIG_SC92031 is not set
+CONFIG_SC92031=m
# CONFIG_NET_POCKET is not set
-# CONFIG_NETDEV_1000 is not set
+CONFIG_ATL2=m
+CONFIG_NETDEV_1000=y
+# CONFIG_ACENIC is not set
+# CONFIG_DL2K is not set
+CONFIG_E1000=m
+# CONFIG_E1000E is not set
+# CONFIG_IP1000 is not set
+# CONFIG_IGB is not set
+# CONFIG_NS83820 is not set
+# CONFIG_HAMACHI is not set
+# CONFIG_YELLOWFIN is not set
+CONFIG_R8169=m
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
+# CONFIG_VIA_VELOCITY is not set
+# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
+# CONFIG_ATL1E is not set
+# CONFIG_ATL1C is not set
+# CONFIG_JME is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
@@ -718,43 +1048,108 @@ CONFIG_VIA_RHINE_NAPI=y
#
# CONFIG_WLAN_PRE80211 is not set
CONFIG_WLAN_80211=y
-# CONFIG_IPW2100 is not set
-# CONFIG_IPW2200 is not set
-# CONFIG_LIBERTAS is not set
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_USB=m
+# CONFIG_LIBERTAS_DEBUG is not set
+CONFIG_LIBERTAS_THINFIRM=m
+CONFIG_LIBERTAS_THINFIRM_USB=m
# CONFIG_AIRO is not set
# CONFIG_HERMES is not set
# CONFIG_ATMEL is not set
# CONFIG_PRISM54 is not set
CONFIG_USB_ZD1201=m
-# CONFIG_RTL8187 is not set
+CONFIG_USB_NET_RNDIS_WLAN=m
+CONFIG_RTL8180=m
+CONFIG_RTL8187=m
+# CONFIG_ADM8211 is not set
+# CONFIG_MAC80211_HWSIM is not set
+CONFIG_P54_COMMON=m
+CONFIG_P54_USB=m
+CONFIG_P54_PCI=m
+CONFIG_ATH5K=m
+# CONFIG_ATH5K_DEBUG is not set
+CONFIG_ATH9K=m
+# CONFIG_ATH9K_DEBUG is not set
+CONFIG_IPW2100=m
+CONFIG_IPW2100_MONITOR=y
+# CONFIG_IPW2100_DEBUG is not set
+CONFIG_IPW2200=m
+CONFIG_IPW2200_MONITOR=y
+CONFIG_IPW2200_RADIOTAP=y
+CONFIG_IPW2200_PROMISCUOUS=y
+CONFIG_IPW2200_QOS=y
+# CONFIG_IPW2200_DEBUG is not set
+CONFIG_LIBIPW=m
+# CONFIG_LIBIPW_DEBUG is not set
+CONFIG_IWLWIFI=m
+CONFIG_IWLCORE=m
+CONFIG_IWLWIFI_LEDS=y
+CONFIG_IWLWIFI_RFKILL=y
+# CONFIG_IWLWIFI_DEBUG is not set
+CONFIG_IWLAGN=m
+CONFIG_IWLAGN_SPECTRUM_MEASUREMENT=y
+CONFIG_IWLAGN_LEDS=y
+CONFIG_IWL4965=y
+CONFIG_IWL5000=y
+CONFIG_IWL3945=m
+CONFIG_IWL3945_RFKILL=y
+CONFIG_IWL3945_SPECTRUM_MEASUREMENT=y
+CONFIG_IWL3945_LEDS=y
+# CONFIG_IWL3945_DEBUG is not set
# CONFIG_HOSTAP is not set
-CONFIG_BCM43XX=m
-CONFIG_BCM43XX_DEBUG=y
-CONFIG_BCM43XX_DMA=y
-CONFIG_BCM43XX_PIO=y
-CONFIG_BCM43XX_DMA_AND_PIO_MODE=y
-# CONFIG_BCM43XX_DMA_MODE is not set
-# CONFIG_BCM43XX_PIO_MODE is not set
+CONFIG_B43=m
+CONFIG_B43_PCI_AUTOSELECT=y
+CONFIG_B43_PCICORE_AUTOSELECT=y
+CONFIG_B43_LEDS=y
+# CONFIG_B43_DEBUG is not set
+CONFIG_B43LEGACY=m
+CONFIG_B43LEGACY_PCI_AUTOSELECT=y
+CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y
+CONFIG_B43LEGACY_LEDS=y
+CONFIG_B43LEGACY_DEBUG=y
+CONFIG_B43LEGACY_DMA=y
+CONFIG_B43LEGACY_PIO=y
+CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y
+# CONFIG_B43LEGACY_DMA_MODE is not set
+# CONFIG_B43LEGACY_PIO_MODE is not set
CONFIG_ZD1211RW=m
# CONFIG_ZD1211RW_DEBUG is not set
+CONFIG_RT2X00=m
+CONFIG_RT2400PCI=m
+CONFIG_RT2500PCI=m
+CONFIG_RT61PCI=m
+CONFIG_RT2500USB=m
+CONFIG_RT73USB=m
+CONFIG_RT2X00_LIB_PCI=m
+CONFIG_RT2X00_LIB_USB=m
+CONFIG_RT2X00_LIB=m
+CONFIG_RT2X00_LIB_FIRMWARE=y
+CONFIG_RT2X00_LIB_CRYPTO=y
+CONFIG_RT2X00_LIB_RFKILL=y
+CONFIG_RT2X00_LIB_LEDS=y
+# CONFIG_RT2X00_DEBUG is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
#
# USB Network Adapters
#
-# CONFIG_USB_CATC is not set
+CONFIG_USB_CATC=m
# CONFIG_USB_KAWETH is not set
-# CONFIG_USB_PEGASUS is not set
-# CONFIG_USB_RTL8150 is not set
-CONFIG_USB_USBNET_MII=m
+CONFIG_USB_PEGASUS=m
+CONFIG_USB_RTL8150=m
CONFIG_USB_USBNET=m
-# CONFIG_USB_NET_AX8817X is not set
+CONFIG_USB_NET_AX8817X=m
CONFIG_USB_NET_CDCETHER=m
CONFIG_USB_NET_DM9601=m
-# CONFIG_USB_NET_GL620A is not set
-# CONFIG_USB_NET_NET1080 is not set
-# CONFIG_USB_NET_PLUSB is not set
-# CONFIG_USB_NET_MCS7830 is not set
-# CONFIG_USB_NET_RNDIS_HOST is not set
+CONFIG_USB_NET_SMSC95XX=m
+CONFIG_USB_NET_GL620A=m
+CONFIG_USB_NET_NET1080=m
+CONFIG_USB_NET_PLUSB=m
+CONFIG_USB_NET_MCS7830=m
+CONFIG_USB_NET_RNDIS_HOST=m
CONFIG_USB_NET_CDC_SUBSET=m
# CONFIG_USB_ALI_M5632 is not set
# CONFIG_USB_AN2720 is not set
@@ -762,15 +1157,28 @@ CONFIG_USB_NET_CDC_SUBSET=m
CONFIG_USB_ARMLINUX=y
# CONFIG_USB_EPSON2888 is not set
# CONFIG_USB_KC2190 is not set
-# CONFIG_USB_NET_ZAURUS is not set
+CONFIG_USB_NET_ZAURUS=m
+CONFIG_USB_HSO=m
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
-# CONFIG_PLIP is not set
-# CONFIG_PPP is not set
-# CONFIG_SLIP is not set
+CONFIG_PLIP=m
+CONFIG_PPP=m
+CONFIG_PPP_MULTILINK=y
+# CONFIG_PPP_FILTER is not set
+CONFIG_PPP_ASYNC=m
+# CONFIG_PPP_SYNC_TTY is not set
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_MPPE=m
+CONFIG_PPPOE=m
+CONFIG_PPPOL2TP=m
+CONFIG_SLIP=m
+CONFIG_SLIP_COMPRESSED=y
+CONFIG_SLHC=m
+CONFIG_SLIP_SMART=y
+CONFIG_SLIP_MODE_SLIP6=y
# CONFIG_NET_FC is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
@@ -792,7 +1200,6 @@ CONFIG_INPUT_MOUSEDEV=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
@@ -806,16 +1213,20 @@ CONFIG_KEYBOARD_ATKBD=y
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
# CONFIG_KEYBOARD_STOWAWAY is not set
+# CONFIG_KEYBOARD_GPIO is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_APPLETOUCH is not set
+# CONFIG_MOUSE_BCM5974 is not set
# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_GPIO is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TABLET is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
CONFIG_INPUT_MISC=y
-CONFIG_INPUT_PCSPKR=y
+CONFIG_INPUT_PCSPKR=m
+# CONFIG_INPUT_APANEL is not set
# CONFIG_INPUT_WISTRON_BTNS is not set
# CONFIG_INPUT_ATLAS_BTNS is not set
# CONFIG_INPUT_ATI_REMOTE is not set
@@ -823,6 +1234,7 @@ CONFIG_INPUT_PCSPKR=y
# CONFIG_INPUT_KEYSPAN_REMOTE is not set
# CONFIG_INPUT_POWERMATE is not set
# CONFIG_INPUT_YEALINK is not set
+# CONFIG_INPUT_CM109 is not set
# CONFIG_INPUT_UINPUT is not set
#
@@ -842,10 +1254,13 @@ CONFIG_SERIO_LIBPS2=y
# Character devices
#
CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_VT_HW_CONSOLE_BINDING is not set
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+CONFIG_NOZOMI=m
#
# Serial drivers
@@ -866,71 +1281,27 @@ CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
# CONFIG_LEGACY_PTYS is not set
# CONFIG_PRINTER is not set
# CONFIG_PPDEV is not set
-# CONFIG_TIPAR is not set
# CONFIG_IPMI_HANDLER is not set
-CONFIG_WATCHDOG=y
-# CONFIG_WATCHDOG_NOWAYOUT is not set
-
-#
-# Watchdog Device Drivers
-#
-# CONFIG_SOFT_WATCHDOG is not set
-# CONFIG_ACQUIRE_WDT is not set
-# CONFIG_ADVANTECH_WDT is not set
-# CONFIG_ALIM1535_WDT is not set
-# CONFIG_ALIM7101_WDT is not set
-# CONFIG_SC520_WDT is not set
-# CONFIG_EUROTECH_WDT is not set
-# CONFIG_IB700_WDT is not set
-# CONFIG_IBMASR is not set
-# CONFIG_WAFER_WDT is not set
-# CONFIG_I6300ESB_WDT is not set
-# CONFIG_ITCO_WDT is not set
-# CONFIG_SC1200_WDT is not set
-# CONFIG_PC87413_WDT is not set
-# CONFIG_60XX_WDT is not set
-# CONFIG_SBC8360_WDT is not set
-# CONFIG_CPU5_WDT is not set
-# CONFIG_SMSC37B787_WDT is not set
-# CONFIG_W83627HF_WDT is not set
-# CONFIG_W83697HF_WDT is not set
-# CONFIG_W83877F_WDT is not set
-# CONFIG_W83977F_WDT is not set
-# CONFIG_MACHZ_WDT is not set
-# CONFIG_SBC_EPX_C3_WATCHDOG is not set
-
-#
-# PCI-based Watchdog Cards
-#
-# CONFIG_PCIPCWATCHDOG is not set
-# CONFIG_WDTPCI is not set
-
-#
-# USB-based Watchdog Cards
-#
-# CONFIG_USBPCWATCHDOG is not set
CONFIG_HW_RANDOM=y
# CONFIG_HW_RANDOM_INTEL is not set
# CONFIG_HW_RANDOM_AMD is not set
CONFIG_HW_RANDOM_GEODE=y
# CONFIG_HW_RANDOM_VIA is not set
# CONFIG_NVRAM is not set
-CONFIG_RTC=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
-# CONFIG_AGP is not set
-# CONFIG_DRM is not set
# CONFIG_MWAVE is not set
+# CONFIG_SCx200_GPIO is not set
# CONFIG_PC8736x_GPIO is not set
CONFIG_NSC_GPIO=m
CONFIG_CS5535_GPIO=m
# CONFIG_RAW_DRIVER is not set
CONFIG_HPET=y
-# CONFIG_HPET_RTC_IRQ is not set
CONFIG_HPET_MMAP=y
CONFIG_HANGCHECK_TIMER=m
# CONFIG_TCG_TPM is not set
@@ -939,16 +1310,14 @@ CONFIG_DEVPORT=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=m
+CONFIG_I2C_HELPER_AUTO=y
#
-# I2C Algorithms
+# I2C Hardware Bus support
#
-CONFIG_I2C_ALGOBIT=y
-# CONFIG_I2C_ALGOPCF is not set
-# CONFIG_I2C_ALGOPCA is not set
#
-# I2C Hardware Bus support
+# PC SMBus host controller drivers
#
# CONFIG_I2C_ALI1535 is not set
# CONFIG_I2C_ALI1563 is not set
@@ -956,34 +1325,48 @@ CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_AMD756 is not set
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
-# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_ISCH is not set
# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_NFORCE2 is not set
-# CONFIG_I2C_OCORES is not set
-# CONFIG_I2C_PARPORT is not set
-# CONFIG_I2C_PARPORT_LIGHT is not set
-# CONFIG_I2C_PROSAVAGE is not set
-# CONFIG_I2C_SAVAGE4 is not set
-# CONFIG_I2C_SIMTEC is not set
-CONFIG_SCx200_ACB=m
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
-# CONFIG_I2C_TAOS_EVM is not set
-# CONFIG_I2C_STUB is not set
-# CONFIG_I2C_TINY_USB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+# CONFIG_I2C_SIMTEC is not set
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT is not set
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Graphics adapter I2C/DDC channel drivers
+#
# CONFIG_I2C_VOODOO3 is not set
#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+CONFIG_SCx200_ACB=m
+
+#
# Miscellaneous I2C Chip support
#
-# CONFIG_SENSORS_DS1337 is not set
-# CONFIG_SENSORS_DS1374 is not set
# CONFIG_DS1682 is not set
-# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_MAX6875 is not set
@@ -992,105 +1375,173 @@ CONFIG_SCx200_ACB=m
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+# CONFIG_SPI_BITBANG is not set
+# CONFIG_SPI_BUTTERFLY is not set
+# CONFIG_SPI_GPIO is not set
+# CONFIG_SPI_LM70_LLP is not set
#
-# SPI support
+# SPI Protocol Masters
+#
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_SPI_TLE62X0 is not set
+CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+# CONFIG_GPIO_BT8XX is not set
+
#
-# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
# CONFIG_W1 is not set
-# CONFIG_POWER_SUPPLY is not set
-CONFIG_HWMON=m
-CONFIG_HWMON_VID=m
-# CONFIG_SENSORS_ABITUGURU is not set
-# CONFIG_SENSORS_ABITUGURU3 is not set
-# CONFIG_SENSORS_AD7418 is not set
-# CONFIG_SENSORS_ADM1021 is not set
-# CONFIG_SENSORS_ADM1025 is not set
-# CONFIG_SENSORS_ADM1026 is not set
-# CONFIG_SENSORS_ADM1029 is not set
-# CONFIG_SENSORS_ADM1031 is not set
-# CONFIG_SENSORS_ADM9240 is not set
-# CONFIG_SENSORS_K8TEMP is not set
-# CONFIG_SENSORS_ASB100 is not set
-# CONFIG_SENSORS_ATXP1 is not set
-# CONFIG_SENSORS_DS1621 is not set
-# CONFIG_SENSORS_F71805F is not set
-# CONFIG_SENSORS_FSCHER is not set
-# CONFIG_SENSORS_FSCPOS is not set
-# CONFIG_SENSORS_GL518SM is not set
-# CONFIG_SENSORS_GL520SM is not set
-# CONFIG_SENSORS_CORETEMP is not set
-# CONFIG_SENSORS_IT87 is not set
-# CONFIG_SENSORS_LM63 is not set
-# CONFIG_SENSORS_LM75 is not set
-# CONFIG_SENSORS_LM77 is not set
-# CONFIG_SENSORS_LM78 is not set
-# CONFIG_SENSORS_LM80 is not set
-# CONFIG_SENSORS_LM83 is not set
-# CONFIG_SENSORS_LM85 is not set
-# CONFIG_SENSORS_LM87 is not set
-# CONFIG_SENSORS_LM90 is not set
-# CONFIG_SENSORS_LM92 is not set
-# CONFIG_SENSORS_LM93 is not set
-# CONFIG_SENSORS_MAX1619 is not set
-# CONFIG_SENSORS_MAX6650 is not set
-# CONFIG_SENSORS_PC87360 is not set
-# CONFIG_SENSORS_PC87427 is not set
-# CONFIG_SENSORS_SIS5595 is not set
-# CONFIG_SENSORS_DME1737 is not set
-# CONFIG_SENSORS_SMSC47M1 is not set
-# CONFIG_SENSORS_SMSC47M192 is not set
-# CONFIG_SENSORS_SMSC47B397 is not set
-# CONFIG_SENSORS_THMC50 is not set
-# CONFIG_SENSORS_VIA686A is not set
-# CONFIG_SENSORS_VT1211 is not set
-# CONFIG_SENSORS_VT8231 is not set
-# CONFIG_SENSORS_W83781D is not set
-# CONFIG_SENSORS_W83791D is not set
-# CONFIG_SENSORS_W83792D is not set
-# CONFIG_SENSORS_W83793 is not set
-# CONFIG_SENSORS_W83L785TS is not set
-CONFIG_SENSORS_W83627HF=m
-# CONFIG_SENSORS_W83627EHF is not set
-# CONFIG_SENSORS_HDAPS is not set
-# CONFIG_SENSORS_APPLESMC is not set
-# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_POWER_SUPPLY=y
+# CONFIG_POWER_SUPPLY_DEBUG is not set
+# CONFIG_PDA_POWER is not set
+# CONFIG_BATTERY_DS2760 is not set
+CONFIG_BATTERY_OLPC=m
+# CONFIG_BATTERY_BQ27x00 is not set
+# CONFIG_HWMON is not set
+CONFIG_THERMAL=m
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+# CONFIG_ACQUIRE_WDT is not set
+# CONFIG_ADVANTECH_WDT is not set
+# CONFIG_ALIM1535_WDT is not set
+# CONFIG_ALIM7101_WDT is not set
+CONFIG_GEODE_WDT=m
+# CONFIG_SC520_WDT is not set
+# CONFIG_EUROTECH_WDT is not set
+# CONFIG_IB700_WDT is not set
+# CONFIG_IBMASR is not set
+# CONFIG_WAFER_WDT is not set
+# CONFIG_I6300ESB_WDT is not set
+# CONFIG_ITCO_WDT is not set
+# CONFIG_IT8712F_WDT is not set
+# CONFIG_IT87_WDT is not set
+# CONFIG_HP_WATCHDOG is not set
+# CONFIG_SC1200_WDT is not set
+# CONFIG_SCx200_WDT is not set
+# CONFIG_PC87413_WDT is not set
+# CONFIG_60XX_WDT is not set
+# CONFIG_SBC8360_WDT is not set
+# CONFIG_SBC7240_WDT is not set
+# CONFIG_CPU5_WDT is not set
+# CONFIG_SMSC_SCH311X_WDT is not set
+# CONFIG_SMSC37B787_WDT is not set
+# CONFIG_W83627HF_WDT is not set
+# CONFIG_W83697HF_WDT is not set
+# CONFIG_W83697UG_WDT is not set
+# CONFIG_W83877F_WDT is not set
+# CONFIG_W83977F_WDT is not set
+# CONFIG_MACHZ_WDT is not set
+# CONFIG_SBC_EPX_C3_WATCHDOG is not set
+
+#
+# PCI-based Watchdog Cards
+#
+# CONFIG_PCIPCWATCHDOG is not set
+# CONFIG_WDTPCI is not set
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB=m
+CONFIG_SSB_SPROM=y
+CONFIG_SSB_PCIHOST_POSSIBLE=y
+CONFIG_SSB_PCIHOST=y
+CONFIG_SSB_B43_PCI_BRIDGE=y
+# CONFIG_SSB_DEBUG is not set
+CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
+CONFIG_SSB_DRIVER_PCICORE=y
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_UCB1400_CORE is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+# CONFIG_REGULATOR is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
-# CONFIG_DAB is not set
+# CONFIG_VIDEO_MEDIA is not set
#
-# Graphics support
+# Multimedia drivers
#
-# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+# CONFIG_DAB is not set
#
-# Display device support
+# Graphics support
#
-# CONFIG_DISPLAY_SUPPORT is not set
+# CONFIG_AGP is not set
+# CONFIG_DRM is not set
# CONFIG_VGASTATE is not set
CONFIG_VIDEO_OUTPUT_CONTROL=m
CONFIG_FB=y
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
CONFIG_FB_CFB_FILLRECT=y
CONFIG_FB_CFB_COPYAREA=y
CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
# CONFIG_FB_SYS_FILLRECT is not set
# CONFIG_FB_SYS_COPYAREA is not set
# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
# CONFIG_FB_SYS_FOPS is not set
-CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_SVGALIB is not set
# CONFIG_FB_MACMODES is not set
# CONFIG_FB_BACKLIGHT is not set
@@ -1108,14 +1559,12 @@ CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_IMSTT is not set
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_VESA is not set
-# CONFIG_FB_HECUBA is not set
+# CONFIG_FB_N411 is not set
# CONFIG_FB_HGA is not set
# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_NVIDIA is not set
# CONFIG_FB_RIVA is not set
-# CONFIG_FB_I810 is not set
# CONFIG_FB_LE80578 is not set
-# CONFIG_FB_INTEL is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
@@ -1123,6 +1572,7 @@ CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_S3 is not set
# CONFIG_FB_SAVAGE is not set
# CONFIG_FB_SIS is not set
+# CONFIG_FB_VIA is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
@@ -1132,46 +1582,39 @@ CONFIG_FB_DEFERRED_IO=y
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_ARK is not set
# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
CONFIG_FB_GEODE=y
CONFIG_FB_GEODE_LX=y
# CONFIG_FB_GEODE_GX is not set
# CONFIG_FB_GEODE_GX1 is not set
# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
+
+#
+# Display device support
+#
+# CONFIG_DISPLAY_SUPPORT is not set
#
# Console display driver support
#
CONFIG_VGA_CONSOLE=y
# CONFIG_VGACON_SOFT_SCROLLBACK is not set
-CONFIG_VIDEO_SELECT=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set
# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set
-CONFIG_FONTS=y
-# CONFIG_FONT_8x8 is not set
+# CONFIG_FONTS is not set
+CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
-# CONFIG_FONT_6x11 is not set
-# CONFIG_FONT_7x14 is not set
-# CONFIG_FONT_PEARL_8x8 is not set
-# CONFIG_FONT_ACORN_8x8 is not set
-# CONFIG_FONT_MINI_4x6 is not set
-# CONFIG_FONT_SUN8x16 is not set
-# CONFIG_FONT_SUN12x22 is not set
-# CONFIG_FONT_10x18 is not set
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_LOGO_LINUX_CLUT224=y
-
-#
-# Sound
-#
CONFIG_SOUND=m
-
-#
-# Advanced Linux Sound Architecture
-#
+CONFIG_SOUND_OSS_CORE=y
CONFIG_SND=m
CONFIG_SND_TIMER=m
CONFIG_SND_PCM=m
@@ -1180,27 +1623,25 @@ CONFIG_SND_OSSEMUL=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_PCM_OSS_PLUGINS=y
-CONFIG_SND_RTCTIMER=m
+# CONFIG_SND_HRTIMER is not set
# CONFIG_SND_DYNAMIC_MINORS is not set
# CONFIG_SND_SUPPORT_OLD_API is not set
# CONFIG_SND_VERBOSE_PROCFS is not set
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
-
-#
-# Generic devices
-#
+CONFIG_SND_VMASTER=y
CONFIG_SND_AC97_CODEC=m
+CONFIG_SND_DRIVERS=y
+# CONFIG_SND_PCSP is not set
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_MTS64 is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
# CONFIG_SND_PORTMAN2X4 is not set
-
-#
-# PCI devices
-#
+CONFIG_SND_AC97_POWER_SAVE=y
+CONFIG_SND_AC97_POWER_SAVE_DEFAULT=1
+CONFIG_SND_PCI=y
# CONFIG_SND_AD1889 is not set
# CONFIG_SND_ALS300 is not set
# CONFIG_SND_ALS4000 is not set
@@ -1210,10 +1651,12 @@ CONFIG_SND_AC97_CODEC=m
# CONFIG_SND_AU8810 is not set
# CONFIG_SND_AU8820 is not set
# CONFIG_SND_AU8830 is not set
+# CONFIG_SND_AW2 is not set
# CONFIG_SND_AZT3328 is not set
# CONFIG_SND_BT87X is not set
# CONFIG_SND_CA0106 is not set
# CONFIG_SND_CMIPCI is not set
+# CONFIG_SND_OXYGEN is not set
# CONFIG_SND_CS4281 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS5530 is not set
@@ -1240,6 +1683,7 @@ CONFIG_SND_CS5535AUDIO=m
# CONFIG_SND_HDA_INTEL is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_HDSPM is not set
+# CONFIG_SND_HIFIER is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_ICE1724 is not set
# CONFIG_SND_INTEL8X0 is not set
@@ -1253,71 +1697,89 @@ CONFIG_SND_CS5535AUDIO=m
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
+# CONFIG_SND_SIS7019 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_VIA82XX is not set
# CONFIG_SND_VIA82XX_MODEM is not set
+# CONFIG_SND_VIRTUOSO is not set
# CONFIG_SND_VX222 is not set
# CONFIG_SND_YMFPCI is not set
-# CONFIG_SND_AC97_POWER_SAVE is not set
-
-#
-# USB devices
-#
-# CONFIG_SND_USB_AUDIO is not set
-# CONFIG_SND_USB_USX2Y is not set
-# CONFIG_SND_USB_CAIAQ is not set
-
-#
-# System on Chip audio support
-#
+# CONFIG_SND_SPI is not set
+# CONFIG_SND_USB is not set
# CONFIG_SND_SOC is not set
-
-#
-# SoC Audio support for SuperH
-#
-
-#
-# Open Sound System
-#
# CONFIG_SOUND_PRIME is not set
CONFIG_AC97_BUS=m
CONFIG_HID_SUPPORT=y
CONFIG_HID=y
# CONFIG_HID_DEBUG is not set
+# CONFIG_HIDRAW is not set
#
# USB Input Devices
#
CONFIG_USB_HID=y
-# CONFIG_USB_HIDINPUT_POWERBOOK is not set
-# CONFIG_HID_FF is not set
+# CONFIG_HID_PID is not set
CONFIG_USB_HIDDEV=y
+
+#
+# Special HID drivers
+#
+CONFIG_HID_COMPAT=y
+CONFIG_HID_A4TECH=y
+CONFIG_HID_APPLE=y
+CONFIG_HID_BELKIN=y
+CONFIG_HID_CHERRY=y
+CONFIG_HID_CHICONY=y
+CONFIG_HID_CYPRESS=y
+CONFIG_HID_EZKEY=y
+CONFIG_HID_GYRATION=y
+CONFIG_HID_LOGITECH=y
+# CONFIG_LOGITECH_FF is not set
+# CONFIG_LOGIRUMBLEPAD2_FF is not set
+CONFIG_HID_MICROSOFT=y
+CONFIG_HID_MONTEREY=y
+CONFIG_HID_NTRIG=y
+CONFIG_HID_PANTHERLORD=y
+# CONFIG_PANTHERLORD_FF is not set
+CONFIG_HID_PETALYNX=y
+CONFIG_HID_SAMSUNG=y
+CONFIG_HID_SONY=y
+CONFIG_HID_SUNPLUS=y
+# CONFIG_GREENASIA_FF is not set
+CONFIG_HID_TOPSEED=y
+# CONFIG_THRUSTMASTER_FF is not set
+# CONFIG_ZEROPLUS_FF is not set
CONFIG_USB_SUPPORT=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
-CONFIG_USB_DEVICE_CLASS=y
+# CONFIG_USB_DEVICE_CLASS is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
CONFIG_USB_SUSPEND=y
-# CONFIG_USB_PERSIST is not set
# CONFIG_USB_OTG is not set
+CONFIG_USB_MON=m
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
#
# USB Host Controller Drivers
#
+# CONFIG_USB_C67X00_HCD is not set
CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_SPLIT_ISO=y
CONFIG_USB_EHCI_ROOT_HUB_TT=y
CONFIG_USB_EHCI_TT_NEWSCHED=y
+# CONFIG_USB_OXU210HP_HCD is not set
# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
CONFIG_USB_OHCI_HCD=y
# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
@@ -1325,31 +1787,37 @@ CONFIG_USB_OHCI_LITTLE_ENDIAN=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_USB_SL811_HCD is not set
# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_WHCI_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
#
# USB Device Class drivers
#
CONFIG_USB_ACM=m
CONFIG_USB_PRINTER=m
+CONFIG_USB_WDM=m
+# CONFIG_USB_TMC is not set
#
-# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may also be needed;
#
#
-# may also be needed; see USB_STORAGE Help for more information
+# see USB_STORAGE Help for more information
#
CONFIG_USB_STORAGE=m
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
-# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_USBAT is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_ONETOUCH is not set
# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
# CONFIG_USB_LIBUSUAL is not set
#
@@ -1357,16 +1825,11 @@ CONFIG_USB_STORAGE=m
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_MICROTEK is not set
-# CONFIG_USB_MON is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
-
-#
-# USB Serial Converter support
-#
# CONFIG_USB_SERIAL is not set
#
@@ -1375,7 +1838,7 @@ CONFIG_USB_STORAGE=m
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_ADUTUX is not set
-# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_SEVSEG is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
@@ -1392,17 +1855,38 @@ CONFIG_USB_STORAGE=m
# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_IOWARRIOR is not set
# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+# CONFIG_USB_GADGET is not set
#
-# USB DSL modem support
+# OTG and related infrastructure
#
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_UWB is not set
+# CONFIG_MMC is not set
+# CONFIG_MEMSTICK is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=m
#
-# USB Gadget Support
+# LED drivers
#
-# CONFIG_USB_GADGET is not set
-# CONFIG_MMC is not set
-# CONFIG_NEW_LEDS is not set
+# CONFIG_LEDS_ALIX2 is not set
+# CONFIG_LEDS_PCA9532 is not set
+# CONFIG_LEDS_GPIO is not set
+# CONFIG_LEDS_CLEVO_MAIL is not set
+# CONFIG_LEDS_PCA955X is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+# CONFIG_LEDS_TRIGGER_TIMER is not set
+# CONFIG_LEDS_TRIGGER_HEARTBEAT is not set
+# CONFIG_LEDS_TRIGGER_BACKLIGHT is not set
+# CONFIG_LEDS_TRIGGER_DEFAULT_ON is not set
+# CONFIG_ACCESSIBILITY is not set
# CONFIG_INFINIBAND is not set
# CONFIG_EDAC is not set
CONFIG_RTC_LIB=y
@@ -1424,6 +1908,7 @@ CONFIG_RTC_INTF_DEV=y
# I2C RTC drivers
#
# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_RTC_DRV_MAX6900 is not set
# CONFIG_RTC_DRV_RS5C372 is not set
@@ -1432,75 +1917,102 @@ CONFIG_RTC_INTF_DEV=y
# CONFIG_RTC_DRV_PCF8563 is not set
# CONFIG_RTC_DRV_PCF8583 is not set
# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
#
# SPI RTC drivers
#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
#
# Platform RTC drivers
#
CONFIG_RTC_DRV_CMOS=y
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
# CONFIG_RTC_DRV_DS1553 is not set
-# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
# CONFIG_RTC_DRV_V3020 is not set
#
# on-CPU RTC drivers
#
-
-#
-# DMA Engine support
-#
-# CONFIG_DMA_ENGINE is not set
-
-#
-# DMA Clients
-#
-
-#
-# DMA Devices
-#
+# CONFIG_DMADEVICES is not set
# CONFIG_AUXDISPLAY is not set
-CONFIG_VIRTUALIZATION=y
-# CONFIG_KVM is not set
+CONFIG_UIO=m
+# CONFIG_UIO_CIF is not set
+# CONFIG_UIO_PDRV is not set
+CONFIG_UIO_PDRV_GENIRQ=m
+# CONFIG_UIO_SMX is not set
+# CONFIG_UIO_SERCOS3 is not set
+# CONFIG_STAGING is not set
+CONFIG_X86_PLATFORM_DEVICES=y
+# CONFIG_ASUS_LAPTOP is not set
+# CONFIG_TC1100_WMI is not set
+# CONFIG_SONY_LAPTOP is not set
+# CONFIG_THINKPAD_ACPI is not set
+# CONFIG_INTEL_MENLOW is not set
+# CONFIG_EEEPC_LAPTOP is not set
+# CONFIG_ACPI_WMI is not set
+# CONFIG_ACPI_ASUS is not set
+# CONFIG_ACPI_TOSHIBA is not set
#
-# Userspace I/O
+# Firmware Drivers
#
-# CONFIG_UIO is not set
+# CONFIG_EDD is not set
+CONFIG_FIRMWARE_MEMMAP=y
+# CONFIG_DELL_RBU is not set
+# CONFIG_DCDBAS is not set
+# CONFIG_DMIID is not set
+# CONFIG_ISCSI_IBFT_FIND is not set
#
# File systems
#
CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
-# CONFIG_EXT2_FS_POSIX_ACL is not set
+CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
-# CONFIG_EXT3_FS_POSIX_ACL is not set
+CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
-# CONFIG_EXT4DEV_FS is not set
+CONFIG_EXT4_FS=m
+# CONFIG_EXT4DEV_COMPAT is not set
+CONFIG_EXT4_FS_XATTR=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+# CONFIG_EXT4_FS_SECURITY is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
+CONFIG_JBD2=m
+# CONFIG_JBD2_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
+CONFIG_FILE_LOCKING=y
# CONFIG_XFS_FS is not set
-# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
-# CONFIG_MINIX_FS is not set
-# CONFIG_ROMFS_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_DNOTIFY=y
CONFIG_INOTIFY=y
CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
-CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
CONFIG_FUSE_FS=m
@@ -1524,7 +2036,7 @@ CONFIG_FAT_DEFAULT_CODEPAGE=437
CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
-# CONFIG_NTFS_RW is not set
+CONFIG_NTFS_RW=y
#
# Pseudo filesystems
@@ -1532,17 +2044,14 @@ CONFIG_NTFS_FS=m
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLBFS is not set
# CONFIG_HUGETLB_PAGE is not set
-CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
-
-#
-# Miscellaneous filesystems
-#
+CONFIG_MISC_FILESYSTEMS=y
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
@@ -1551,35 +2060,37 @@ CONFIG_RAMFS=y
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
CONFIG_CRAMFS=m
+CONFIG_SQUASHFS=m
+# CONFIG_SQUASHFS_EMBEDDED is not set
+CONFIG_SQUASHFS_FRAGMENT_CACHE_SIZE=3
# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
# CONFIG_HPFS_FS is not set
# CONFIG_QNX4FS_FS is not set
+# CONFIG_ROMFS_FS is not set
# CONFIG_SYSV_FS is not set
# CONFIG_UFS_FS is not set
-
-#
-# Network File Systems
-#
-CONFIG_NFS_FS=m
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
-# CONFIG_NFS_DIRECTIO is not set
+CONFIG_ROOT_NFS=y
CONFIG_NFSD=m
CONFIG_NFSD_V2_ACL=y
CONFIG_NFSD_V3=y
CONFIG_NFSD_V3_ACL=y
CONFIG_NFSD_V4=y
-CONFIG_NFSD_TCP=y
-CONFIG_LOCKD=m
+CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
-CONFIG_NFS_ACL_SUPPORT=m
+CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=m
-CONFIG_SUNRPC_GSS=m
-CONFIG_SUNRPC_BIND34=y
-CONFIG_RPCSEC_GSS_KRB5=m
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+# CONFIG_SUNRPC_REGISTER_V4 is not set
+CONFIG_RPCSEC_GSS_KRB5=y
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
CONFIG_CIFS=m
@@ -1590,8 +2101,7 @@ CONFIG_CIFS_POSIX=y
# CONFIG_CIFS_DEBUG2 is not set
CONFIG_CIFS_EXPERIMENTAL=y
# CONFIG_NCP_FS is not set
-CONFIG_CODA_FS=m
-# CONFIG_CODA_FS_OLD_API is not set
+# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
@@ -1599,16 +2109,12 @@ CONFIG_CODA_FS=m
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
-
-#
-# Native Language Support
-#
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="utf-8"
CONFIG_NLS_CODEPAGE_437=m
# CONFIG_NLS_CODEPAGE_737 is not set
# CONFIG_NLS_CODEPAGE_775 is not set
-# CONFIG_NLS_CODEPAGE_850 is not set
+CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
# CONFIG_NLS_CODEPAGE_855 is not set
# CONFIG_NLS_CODEPAGE_857 is not set
@@ -1643,24 +2149,19 @@ CONFIG_NLS_ISO8859_2=m
# CONFIG_NLS_KOI8_R is not set
# CONFIG_NLS_KOI8_U is not set
CONFIG_NLS_UTF8=y
-
-#
-# Distributed Lock Manager
-#
# CONFIG_DLM is not set
-CONFIG_INSTRUMENTATION=y
-# CONFIG_PROFILING is not set
-# CONFIG_KPROBES is not set
#
# Kernel hacking
#
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_PRINTK_TIME=y
-CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_FRAME_WARN=1024
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
-# CONFIG_DEBUG_FS is not set
+CONFIG_DEBUG_FS=y
# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_SHIRQ is not set
@@ -1668,6 +2169,7 @@ CONFIG_DEBUG_KERNEL=y
CONFIG_SCHED_DEBUG=y
# CONFIG_SCHEDSTATS is not set
CONFIG_TIMER_STATS=y
+# CONFIG_DEBUG_OBJECTS is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_RT_MUTEXES is not set
@@ -1679,89 +2181,220 @@ CONFIG_TIMER_STATS=y
# CONFIG_LOCK_STAT is not set
# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+CONFIG_STACKTRACE=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_VIRTUAL is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+CONFIG_ARCH_WANT_FRAME_POINTERS=y
# CONFIG_FRAME_POINTER is not set
-CONFIG_FORCED_INLINING=y
+# CONFIG_BOOT_PRINTK_DELAY is not set
# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+# CONFIG_SYSCTL_SYSCALL_CHECK is not set
+CONFIG_USER_STACKTRACE_SUPPORT=y
+CONFIG_NOP_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_HW_BRANCH_TRACER=y
+CONFIG_RING_BUFFER=y
+CONFIG_TRACING=y
+
+#
+# Tracers
+#
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_IRQSOFF_TRACER is not set
+# CONFIG_PREEMPT_TRACER is not set
+# CONFIG_SYSPROF_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_POWER_TRACER is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_HW_BRANCH_TRACER is not set
+# CONFIG_FTRACE_STARTUP_TEST is not set
+# CONFIG_MMIOTRACE is not set
+# CONFIG_PROVIDE_OHCI1394_DMA_INIT is not set
+# CONFIG_DYNAMIC_PRINTK_DEBUG is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+# CONFIG_STRICT_DEVMEM is not set
+# CONFIG_X86_VERBOSE_BOOTUP is not set
CONFIG_EARLY_PRINTK=y
+# CONFIG_EARLY_PRINTK_DBGP is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
# CONFIG_DEBUG_PAGEALLOC is not set
+# CONFIG_X86_PTDUMP is not set
# CONFIG_DEBUG_RODATA is not set
+# CONFIG_DEBUG_NX_TEST is not set
CONFIG_4KSTACKS=y
-CONFIG_X86_FIND_SMP_CONFIG=y
-CONFIG_X86_MPPARSE=y
CONFIG_DOUBLEFAULT=y
+CONFIG_HAVE_MMIOTRACE_SUPPORT=y
+CONFIG_IO_DELAY_TYPE_0X80=0
+CONFIG_IO_DELAY_TYPE_0XED=1
+CONFIG_IO_DELAY_TYPE_UDELAY=2
+CONFIG_IO_DELAY_TYPE_NONE=3
+CONFIG_IO_DELAY_0X80=y
+# CONFIG_IO_DELAY_0XED is not set
+# CONFIG_IO_DELAY_UDELAY is not set
+# CONFIG_IO_DELAY_NONE is not set
+CONFIG_DEFAULT_IO_DELAY_TYPE=0
+# CONFIG_DEBUG_BOOT_PARAMS is not set
+# CONFIG_CPA_DEBUG is not set
+# CONFIG_OPTIMIZE_INLINING is not set
#
# Security options
#
# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+# CONFIG_SECURITY_FILE_CAPABILITIES is not set
+CONFIG_XOR_BLOCKS=m
+CONFIG_ASYNC_CORE=m
+CONFIG_ASYNC_MEMCPY=m
+CONFIG_ASYNC_XOR=m
CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_FIPS=y
CONFIG_CRYPTO_ALGAPI=y
-CONFIG_CRYPTO_ABLKCIPHER=m
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD=m
+CONFIG_CRYPTO_AEAD2=y
CONFIG_CRYPTO_BLKCIPHER=y
-CONFIG_CRYPTO_HASH=m
-CONFIG_CRYPTO_MANAGER=m
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG=m
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_GF128MUL=m
+CONFIG_CRYPTO_NULL=m
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_TEST=m
+
+#
+# Authenticated Encryption with Associated Data
+#
+CONFIG_CRYPTO_CCM=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_SEQIV=m
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CTR=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_ECB=m
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+
+#
+# Hash modes
+#
CONFIG_CRYPTO_HMAC=m
CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_NULL=m
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=m
+# CONFIG_CRYPTO_CRC32C_INTEL is not set
CONFIG_CRYPTO_MD4=m
-CONFIG_CRYPTO_MD5=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
CONFIG_CRYPTO_SHA1=m
CONFIG_CRYPTO_SHA256=m
CONFIG_CRYPTO_SHA512=m
-CONFIG_CRYPTO_WP512=m
CONFIG_CRYPTO_TGR192=m
-CONFIG_CRYPTO_GF128MUL=m
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_CBC=m
-CONFIG_CRYPTO_PCBC=m
-CONFIG_CRYPTO_LRW=m
-CONFIG_CRYPTO_CRYPTD=m
-CONFIG_CRYPTO_DES=m
-CONFIG_CRYPTO_FCRYPT=m
-CONFIG_CRYPTO_BLOWFISH=m
-CONFIG_CRYPTO_TWOFISH=m
-CONFIG_CRYPTO_TWOFISH_COMMON=m
-CONFIG_CRYPTO_TWOFISH_586=m
-CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_WP512=m
+
+#
+# Ciphers
+#
CONFIG_CRYPTO_AES=m
CONFIG_CRYPTO_AES_586=m
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_ARC4=m
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
CONFIG_CRYPTO_CAST5=m
CONFIG_CRYPTO_CAST6=m
-CONFIG_CRYPTO_TEA=m
-CONFIG_CRYPTO_ARC4=m
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_FCRYPT=m
CONFIG_CRYPTO_KHAZAD=m
-CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_SALSA20=m
+CONFIG_CRYPTO_SALSA20_586=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_TWOFISH_COMMON=m
+CONFIG_CRYPTO_TWOFISH_586=m
+
+#
+# Compression
+#
CONFIG_CRYPTO_DEFLATE=m
-CONFIG_CRYPTO_MICHAEL_MIC=m
-CONFIG_CRYPTO_CRC32C=m
-CONFIG_CRYPTO_CAMELLIA=m
-CONFIG_CRYPTO_TEST=m
+CONFIG_CRYPTO_LZO=m
+
+#
+# Random Number Generation
+#
+CONFIG_CRYPTO_ANSI_CPRNG=m
CONFIG_CRYPTO_HW=y
# CONFIG_CRYPTO_DEV_PADLOCK is not set
-CONFIG_CRYPTO_DEV_GEODE=y
+CONFIG_CRYPTO_DEV_GEODE=m
+# CONFIG_CRYPTO_DEV_HIFN_795X is not set
+CONFIG_HAVE_KVM=y
+# CONFIG_VIRTUALIZATION is not set
#
# Library routines
#
CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_FIRST_BIT=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
CONFIG_CRC_CCITT=m
-# CONFIG_CRC16 is not set
-# CONFIG_CRC_ITU_T is not set
+CONFIG_CRC16=m
+# CONFIG_CRC_T10DIF is not set
+CONFIG_CRC_ITU_T=m
CONFIG_CRC32=y
# CONFIG_CRC7 is not set
CONFIG_LIBCRC32C=m
CONFIG_AUDIT_GENERIC=y
CONFIG_ZLIB_INFLATE=m
CONFIG_ZLIB_DEFLATE=m
+CONFIG_LZO_COMPRESS=m
+CONFIG_LZO_DECOMPRESS=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
CONFIG_TEXTSEARCH_BM=m
@@ -1770,7 +2403,3 @@ CONFIG_PLIST=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
CONFIG_HAS_DMA=y
-CONFIG_GENERIC_HARDIRQS=y
-CONFIG_GENERIC_IRQ_PROBE=y
-CONFIG_X86_BIOS_REBOOT=y
-CONFIG_KTIME_SCALAR=y
diff --git a/recipes/linux/linux_2.6.25.bb b/recipes/linux/linux_2.6.25.bb
index b529b75..fabba65 100644
--- a/recipes/linux/linux_2.6.25.bb
+++ b/recipes/linux/linux_2.6.25.bb
@@ -8,7 +8,6 @@ DEFAULT_PREFERENCE_mpc8313e-rdb = "1"
DEFAULT_PREFERENCE_kilauea = "1"
DEFAULT_PREFERENCE_sequoia = "1"
DEFAULT_PREFERENCE_cm-x270 = "-1"
-DEFAULT_PREFERENCE_alix = "1"
DEFAULT_PREFERENCE_at32stk1000 = "1"
DEFAULT_PREFERENCE_at91-l9260 = "1"
DEFAULT_PREFERENCE_db1200 = "1"
diff --git a/recipes/linux/linux_2.6.29.bb b/recipes/linux/linux_2.6.29.bb
index 4850fba..89767d6 100644
--- a/recipes/linux/linux_2.6.29.bb
+++ b/recipes/linux/linux_2.6.29.bb
@@ -14,6 +14,7 @@ DEFAULT_PREFERENCE_atngw100 = "1"
DEFAULT_PREFERENCE_micro2440 = "1"
DEFAULT_PREFERENCE_ep93xx = "1"
DEFAULT_PREFERENCE_cm-x270 = "1"
+DEFAULT_PREFERENCE_geodelx = "1"
SRC_URI = "${KERNELORG_MIRROR}/pub/linux/kernel/v2.6/linux-2.6.29.tar.bz2 \
file://defconfig"
--
1.6.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 14:46 Some updates for GeodeLX based devices Marcin Juszkiewicz
` (4 preceding siblings ...)
2009-05-13 14:46 ` [PATCH 5/6] linux: drop alix, move geodelx to 2.6.29 Marcin Juszkiewicz
@ 2009-05-13 14:46 ` Marcin Juszkiewicz
2009-05-13 14:56 ` Koen Kooi
5 siblings, 1 reply; 17+ messages in thread
From: Marcin Juszkiewicz @ 2009-05-13 14:46 UTC (permalink / raw)
To: openembedded-devel; +Cc: Marcin Juszkiewicz
From: Marcin Juszkiewicz <hrw@openembedded.org>
Signed-off-by: Marcin Juszkiewicz <hrw@openembedded.org>
---
conf/distro/angstrom-2008.1.conf | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/conf/distro/angstrom-2008.1.conf b/conf/distro/angstrom-2008.1.conf
index a466834..b5dbc48 100644
--- a/conf/distro/angstrom-2008.1.conf
+++ b/conf/distro/angstrom-2008.1.conf
@@ -101,6 +101,7 @@ ANGSTROM_GCC_VERSION_bfin = "4.1.2"
ANGSTROM_GCC_VERSION_486sx = "4.3.3"
ANGSTROM_GCC_VERSION_armv7a = "4.3.3"
+ANGSTROM_GCC_VERSION_geode = "4.3.3"
# Uncomment this if want need to build an armv7a kernel with CSL toolchain (<2.6.27 don't boot with mainline gcc)
#KERNEL_CCSUFFIX_armv7a= "-4.2.1+csl-arm-2007q3-53"
--
1.6.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 14:46 ` [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices Marcin Juszkiewicz
@ 2009-05-13 14:56 ` Koen Kooi
2009-05-13 15:18 ` Tom Rini
2009-05-13 17:37 ` Marcin Juszkiewicz
0 siblings, 2 replies; 17+ messages in thread
From: Koen Kooi @ 2009-05-13 14:56 UTC (permalink / raw)
To: openembedded-devel
On 13-05-09 16:46, Marcin Juszkiewicz wrote:
> From: Marcin Juszkiewicz<hrw@openembedded.org>
>
>
> Signed-off-by: Marcin Juszkiewicz<hrw@openembedded.org>
> ---
> conf/distro/angstrom-2008.1.conf | 1 +
> 1 files changed, 1 insertions(+), 0 deletions(-)
>
> diff --git a/conf/distro/angstrom-2008.1.conf b/conf/distro/angstrom-2008.1.conf
> index a466834..b5dbc48 100644
> --- a/conf/distro/angstrom-2008.1.conf
> +++ b/conf/distro/angstrom-2008.1.conf
> @@ -101,6 +101,7 @@ ANGSTROM_GCC_VERSION_bfin = "4.1.2"
>
> ANGSTROM_GCC_VERSION_486sx = "4.3.3"
> ANGSTROM_GCC_VERSION_armv7a = "4.3.3"
> +ANGSTROM_GCC_VERSION_geode = "4.3.3"
>
> # Uncomment this if want need to build an armv7a kernel with CSL toolchain (<2.6.27 don't boot with mainline gcc)
> #KERNEL_CCSUFFIX_armv7a= "-4.2.1+csl-arm-2007q3-53"
NAK, this would interfere with an outstanding patch that Graeme and I
are testing:
http://dominion.thruhere.net/koen/OE/angstrom-dev-toolchain.diff
regards,
Koen
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 14:56 ` Koen Kooi
@ 2009-05-13 15:18 ` Tom Rini
2009-05-13 15:22 ` Philip Balister
2009-05-13 17:10 ` Koen Kooi
2009-05-13 17:37 ` Marcin Juszkiewicz
1 sibling, 2 replies; 17+ messages in thread
From: Tom Rini @ 2009-05-13 15:18 UTC (permalink / raw)
To: openembedded-devel
On Wed, May 13, 2009 at 04:56:58PM +0200, Koen Kooi wrote:
> On 13-05-09 16:46, Marcin Juszkiewicz wrote:
>> From: Marcin Juszkiewicz<hrw@openembedded.org>
>>
>>
>> Signed-off-by: Marcin Juszkiewicz<hrw@openembedded.org>
>> ---
>> conf/distro/angstrom-2008.1.conf | 1 +
>> 1 files changed, 1 insertions(+), 0 deletions(-)
>>
>> diff --git a/conf/distro/angstrom-2008.1.conf b/conf/distro/angstrom-2008.1.conf
>> index a466834..b5dbc48 100644
>> --- a/conf/distro/angstrom-2008.1.conf
>> +++ b/conf/distro/angstrom-2008.1.conf
>> @@ -101,6 +101,7 @@ ANGSTROM_GCC_VERSION_bfin = "4.1.2"
>>
>> ANGSTROM_GCC_VERSION_486sx = "4.3.3"
>> ANGSTROM_GCC_VERSION_armv7a = "4.3.3"
>> +ANGSTROM_GCC_VERSION_geode = "4.3.3"
>>
>> # Uncomment this if want need to build an armv7a kernel with CSL toolchain (<2.6.27 don't boot with mainline gcc)
>> #KERNEL_CCSUFFIX_armv7a= "-4.2.1+csl-arm-2007q3-53"
>
> NAK, this would interfere with an outstanding patch that Graeme and I
> are testing:
>
> http://dominion.thruhere.net/koen/OE/angstrom-dev-toolchain.diff
wrt that patch, is there a reason you aren't bumping ppc as well? As an
old PPC guy, that's always had me perplexed..
--
Tom Rini
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 15:18 ` Tom Rini
@ 2009-05-13 15:22 ` Philip Balister
2009-05-13 15:48 ` Tom Rini
2009-05-13 17:10 ` Koen Kooi
1 sibling, 1 reply; 17+ messages in thread
From: Philip Balister @ 2009-05-13 15:22 UTC (permalink / raw)
To: openembedded-devel
[-- Attachment #1: Type: text/plain, Size: 1391 bytes --]
Tom Rini wrote:
> On Wed, May 13, 2009 at 04:56:58PM +0200, Koen Kooi wrote:
>> On 13-05-09 16:46, Marcin Juszkiewicz wrote:
>>> From: Marcin Juszkiewicz<hrw@openembedded.org>
>>>
>>>
>>> Signed-off-by: Marcin Juszkiewicz<hrw@openembedded.org>
>>> ---
>>> conf/distro/angstrom-2008.1.conf | 1 +
>>> 1 files changed, 1 insertions(+), 0 deletions(-)
>>>
>>> diff --git a/conf/distro/angstrom-2008.1.conf b/conf/distro/angstrom-2008.1.conf
>>> index a466834..b5dbc48 100644
>>> --- a/conf/distro/angstrom-2008.1.conf
>>> +++ b/conf/distro/angstrom-2008.1.conf
>>> @@ -101,6 +101,7 @@ ANGSTROM_GCC_VERSION_bfin = "4.1.2"
>>>
>>> ANGSTROM_GCC_VERSION_486sx = "4.3.3"
>>> ANGSTROM_GCC_VERSION_armv7a = "4.3.3"
>>> +ANGSTROM_GCC_VERSION_geode = "4.3.3"
>>>
>>> # Uncomment this if want need to build an armv7a kernel with CSL toolchain (<2.6.27 don't boot with mainline gcc)
>>> #KERNEL_CCSUFFIX_armv7a= "-4.2.1+csl-arm-2007q3-53"
>> NAK, this would interfere with an outstanding patch that Graeme and I
>> are testing:
>>
>> http://dominion.thruhere.net/koen/OE/angstrom-dev-toolchain.diff
>
> wrt that patch, is there a reason you aren't bumping ppc as well? As an
> old PPC guy, that's always had me perplexed..
There are rumours of problems. But I suspect we do not know specifics.
Any testing would be great :)
Philip
[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/x-pkcs7-signature, Size: 3303 bytes --]
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 15:22 ` Philip Balister
@ 2009-05-13 15:48 ` Tom Rini
2009-05-13 19:36 ` Tom Rini
0 siblings, 1 reply; 17+ messages in thread
From: Tom Rini @ 2009-05-13 15:48 UTC (permalink / raw)
To: openembedded-devel
On Wed, May 13, 2009 at 11:22:52AM -0400, Philip Balister wrote:
> Tom Rini wrote:
>> On Wed, May 13, 2009 at 04:56:58PM +0200, Koen Kooi wrote:
>>> On 13-05-09 16:46, Marcin Juszkiewicz wrote:
>>>> From: Marcin Juszkiewicz<hrw@openembedded.org>
>>>>
>>>>
>>>> Signed-off-by: Marcin Juszkiewicz<hrw@openembedded.org>
>>>> ---
>>>> conf/distro/angstrom-2008.1.conf | 1 +
>>>> 1 files changed, 1 insertions(+), 0 deletions(-)
>>>>
>>>> diff --git a/conf/distro/angstrom-2008.1.conf b/conf/distro/angstrom-2008.1.conf
>>>> index a466834..b5dbc48 100644
>>>> --- a/conf/distro/angstrom-2008.1.conf
>>>> +++ b/conf/distro/angstrom-2008.1.conf
>>>> @@ -101,6 +101,7 @@ ANGSTROM_GCC_VERSION_bfin = "4.1.2"
>>>>
>>>> ANGSTROM_GCC_VERSION_486sx = "4.3.3"
>>>> ANGSTROM_GCC_VERSION_armv7a = "4.3.3"
>>>> +ANGSTROM_GCC_VERSION_geode = "4.3.3"
>>>>
>>>> # Uncomment this if want need to build an armv7a kernel with CSL toolchain (<2.6.27 don't boot with mainline gcc)
>>>> #KERNEL_CCSUFFIX_armv7a= "-4.2.1+csl-arm-2007q3-53"
>>> NAK, this would interfere with an outstanding patch that Graeme and I
>>> are testing:
>>>
>>> http://dominion.thruhere.net/koen/OE/angstrom-dev-toolchain.diff
>>
>> wrt that patch, is there a reason you aren't bumping ppc as well? As an
>> old PPC guy, that's always had me perplexed..
>
> There are rumours of problems. But I suspect we do not know specifics.
> Any testing would be great :)
OK, I've got a 405GP eval board dug up, I'll get a 'make check' going
sometime soon and report back. That should cover the xilinx case too,
fwiw.
--
Tom Rini
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 15:18 ` Tom Rini
2009-05-13 15:22 ` Philip Balister
@ 2009-05-13 17:10 ` Koen Kooi
2009-05-13 18:01 ` Leon Woestenberg
1 sibling, 1 reply; 17+ messages in thread
From: Koen Kooi @ 2009-05-13 17:10 UTC (permalink / raw)
To: openembedded-devel
On 13-05-09 17:18, Tom Rini wrote:
> On Wed, May 13, 2009 at 04:56:58PM +0200, Koen Kooi wrote:
>> On 13-05-09 16:46, Marcin Juszkiewicz wrote:
>>> From: Marcin Juszkiewicz<hrw@openembedded.org>
>>>
>>>
>>> Signed-off-by: Marcin Juszkiewicz<hrw@openembedded.org>
>>> ---
>>> conf/distro/angstrom-2008.1.conf | 1 +
>>> 1 files changed, 1 insertions(+), 0 deletions(-)
>>>
>>> diff --git a/conf/distro/angstrom-2008.1.conf b/conf/distro/angstrom-2008.1.conf
>>> index a466834..b5dbc48 100644
>>> --- a/conf/distro/angstrom-2008.1.conf
>>> +++ b/conf/distro/angstrom-2008.1.conf
>>> @@ -101,6 +101,7 @@ ANGSTROM_GCC_VERSION_bfin = "4.1.2"
>>>
>>> ANGSTROM_GCC_VERSION_486sx = "4.3.3"
>>> ANGSTROM_GCC_VERSION_armv7a = "4.3.3"
>>> +ANGSTROM_GCC_VERSION_geode = "4.3.3"
>>>
>>> # Uncomment this if want need to build an armv7a kernel with CSL toolchain (<2.6.27 don't boot with mainline gcc)
>>> #KERNEL_CCSUFFIX_armv7a= "-4.2.1+csl-arm-2007q3-53"
>>
>> NAK, this would interfere with an outstanding patch that Graeme and I
>> are testing:
>>
>> http://dominion.thruhere.net/koen/OE/angstrom-dev-toolchain.diff
>
> wrt that patch, is there a reason you aren't bumping ppc as well? As an
> old PPC guy, that's always had me perplexed..
When adding PPC support I had loads of troubles compiling gcc and glibc
due to sqrt and type size problems.
My efika is too busy serving stuff to serve as a testbed and my
dht-walnut lacks a psu currently, so I'm a bit apprehensive about
bumping toolchains without runtime testing them.
If console-image actually builds with gcc 4.3.3 + binutils 2.18, that
would be a *huge* step forward.
regards,
Koen
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 14:56 ` Koen Kooi
2009-05-13 15:18 ` Tom Rini
@ 2009-05-13 17:37 ` Marcin Juszkiewicz
1 sibling, 0 replies; 17+ messages in thread
From: Marcin Juszkiewicz @ 2009-05-13 17:37 UTC (permalink / raw)
To: openembedded-devel
Dnia środa, 13 maja 2009 o 16:56:58 Koen Kooi napisał(a):
> > +++ b/conf/distro/angstrom-2008.1.conf
> > +ANGSTROM_GCC_VERSION_geode = "4.3.3"
> NAK, this would interfere with an outstanding patch that Graeme and I
> are testing:
>
> http://dominion.thruhere.net/koen/OE/angstrom-dev-toolchain.diff
OK, I dropped 6/6 patch from local branch and added your change. Will do
build from scratch and test on device.
Regards,
--
JID: hrw@jabber.org
Website: http://marcin.juszkiewicz.com.pl/
LinkedIn: http://www.linkedin.com/in/marcinjuszkiewicz
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 17:10 ` Koen Kooi
@ 2009-05-13 18:01 ` Leon Woestenberg
2009-05-13 18:11 ` Koen Kooi
0 siblings, 1 reply; 17+ messages in thread
From: Leon Woestenberg @ 2009-05-13 18:01 UTC (permalink / raw)
To: openembedded-devel
Hello,
On Wed, May 13, 2009 at 7:10 PM, Koen Kooi <k.kooi@student.utwente.nl> wrote:
> On 13-05-09 17:18, Tom Rini wrote:
>> On Wed, May 13, 2009 at 04:56:58PM +0200, Koen Kooi wrote:
>>> On 13-05-09 16:46, Marcin Juszkiewicz wrote:
>>>> From: Marcin Juszkiewicz<hrw@openembedded.org>
>>>> Signed-off-by: Marcin Juszkiewicz<hrw@openembedded.org>
>>
>> wrt that patch, is there a reason you aren't bumping ppc as well? As an
>> old PPC guy, that's always had me perplexed..
>
Being old and having PPC boards on my desktop spaces as well I
recently got the same level of perplexity, but there's only myself to
blame.
I did recently look elsewhere:
http://www.oselas.com/oselas/toolchain/index_en.html
That OSELAS toolchain shows the following in its support grid:
gcc-4.3.2
glibc-2.8
linux-2.6.27
I extracted and built that toolchain. I saw no patches needed for ppc.
It doesn't mention binutils version - I can check my build.
> When adding PPC support I had loads of troubles compiling gcc and glibc due
> to sqrt and type size problems.
>
Ah, I remember.
> My efika is too busy serving stuff to serve as a testbed and my dht-walnut
> lacks a psu currently, so I'm a bit apprehensive about bumping toolchains
> without runtime testing them.
> If console-image actually builds with gcc 4.3.3 + binutils 2.18, that would
> be a *huge* step forward.
>
Agreed. The old PPC guys should check this first. :-) It's on my todo
(which gives zero information on if it ever gets of).
I only have e300 targets to test.
I (also) blew my EFIKA.
Regards,
--
Leon
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 18:01 ` Leon Woestenberg
@ 2009-05-13 18:11 ` Koen Kooi
0 siblings, 0 replies; 17+ messages in thread
From: Koen Kooi @ 2009-05-13 18:11 UTC (permalink / raw)
To: openembedded-devel
On 13-05-09 20:01, Leon Woestenberg wrote:
> Hello,
>
> On Wed, May 13, 2009 at 7:10 PM, Koen Kooi<k.kooi@student.utwente.nl> wrote:
>> On 13-05-09 17:18, Tom Rini wrote:
>>> On Wed, May 13, 2009 at 04:56:58PM +0200, Koen Kooi wrote:
>>>> On 13-05-09 16:46, Marcin Juszkiewicz wrote:
>>>>> From: Marcin Juszkiewicz<hrw@openembedded.org>
>>>>> Signed-off-by: Marcin Juszkiewicz<hrw@openembedded.org>
>>>
>>> wrt that patch, is there a reason you aren't bumping ppc as well? As an
>>> old PPC guy, that's always had me perplexed..
>>
>
> Being old and having PPC boards on my desktop spaces as well I
> recently got the same level of perplexity, but there's only myself to
> blame.
>
> I did recently look elsewhere:
> http://www.oselas.com/oselas/toolchain/index_en.html
>
> That OSELAS toolchain shows the following in its support grid:
>
> gcc-4.3.2
> glibc-2.8
> linux-2.6.27
>
> I extracted and built that toolchain. I saw no patches needed for ppc.
The move to a newer glibc is also in the works, but that requires
testing as well. That will happen next month to give the gcc+binutils
change enough time to show bugs.
regards,
Koen
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 15:48 ` Tom Rini
@ 2009-05-13 19:36 ` Tom Rini
2009-05-13 20:43 ` Koen Kooi
0 siblings, 1 reply; 17+ messages in thread
From: Tom Rini @ 2009-05-13 19:36 UTC (permalink / raw)
To: openembedded-devel
On Wed, May 13, 2009 at 08:48:42AM -0700, Tom Rini wrote:
[snip]
> OK, I've got a 405GP eval board dug up, I'll get a 'make check' going
> sometime soon and report back. That should cover the xilinx case too,
> fwiw.
OK, console-image built, but only with hdparm_6.6 as I'm getting a
checksum mismatch with 6.9. Digging up good hardware is taking a bit
longer, but I'll hopefully have something soon.
--
Tom Rini
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices
2009-05-13 19:36 ` Tom Rini
@ 2009-05-13 20:43 ` Koen Kooi
0 siblings, 0 replies; 17+ messages in thread
From: Koen Kooi @ 2009-05-13 20:43 UTC (permalink / raw)
To: openembedded-devel
On 13-05-09 21:36, Tom Rini wrote:
> On Wed, May 13, 2009 at 08:48:42AM -0700, Tom Rini wrote:
> [snip]
>> OK, I've got a 405GP eval board dug up, I'll get a 'make check' going
>> sometime soon and report back. That should cover the xilinx case too,
>> fwiw.
>
> OK, console-image built, but only with hdparm_6.6 as I'm getting a
> checksum mismatch with 6.9. Digging up good hardware is taking a bit
> longer, but I'll hopefully have something soon.
Thanks!
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2009-05-13 20:50 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-05-13 14:46 Some updates for GeodeLX based devices Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 1/6] Remove alix machine, update geodelx one to use Alix settings Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 2/6] kaeilos/sane-feed: remove alix, mark geodelx as i586 Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 3/6] kaeilos.inc/sane-feed.inc: use spaces instead of tabs Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 4/6] kaeilos: use include/sane-feed.inc Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 5/6] linux: drop alix, move geodelx to 2.6.29 Marcin Juszkiewicz
2009-05-13 14:46 ` [PATCH 6/6] angstrom: use GCC 4.3.3 for Geode devices Marcin Juszkiewicz
2009-05-13 14:56 ` Koen Kooi
2009-05-13 15:18 ` Tom Rini
2009-05-13 15:22 ` Philip Balister
2009-05-13 15:48 ` Tom Rini
2009-05-13 19:36 ` Tom Rini
2009-05-13 20:43 ` Koen Kooi
2009-05-13 17:10 ` Koen Kooi
2009-05-13 18:01 ` Leon Woestenberg
2009-05-13 18:11 ` Koen Kooi
2009-05-13 17:37 ` Marcin Juszkiewicz
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.