[PATCH 7/8] ARM64: dts: meson-gxl-p23x: Add SD/SDIO/MMC and PWM nodes

[khilman@baylibre.com (Kevin Hilman)]

Neil Armstrong <narmstrong@baylibre.com> writes:

> Add SD/SDIO/MMC nodes and PWM 32768Hz clock configuration to provide
> storage and WiFi functionality on the p23x boards.

Just curious... what storage functionality are you referring to here?

Kevin

> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
>  .../boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi     | 112 +++++++++++++++++++++
>  1 file changed, 112 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi
> index 666fe2b..7830809 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p23x.dtsi
> @@ -56,6 +56,46 @@
>  		device_type = "memory";
>  		reg = <0x0 0x0 0x0 0x80000000>;
>  	};
> +
> +	vddio_boot: regulator-vddio_boot {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_BOOT";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	vddao_3v3: regulator-vddao_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	vcc_3v3: regulator-vcc_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
>  };
>  
>  /* This UART is brought out to the DB9 connector */
> @@ -64,3 +104,75 @@
>  	pinctrl-0 = <&uart_ao_a_pins>;
>  	pinctrl-names = "default";
>  };
> +
> +/* Wireless SDIO Module */
> +&sd_emmc_a {
> +	status = "okay";
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-names = "default";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <100000000>;
> +
> +	non-removable;
> +	disable-wp;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +
> +	brcmf: bcrmf at 1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +	};
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> +	status = "okay";
> +	pinctrl-0 = <&sdcard_pins>;
> +	pinctrl-names = "default";
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <100000000>;
> +	disable-wp;
> +
> +	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
> +	cd-inverted;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> +	status = "okay";
> +	pinctrl-0 = <&emmc_pins>;
> +	pinctrl-names = "default";
> +
> +	bus-width = <8>;
> +	cap-sd-highspeed;
> +	cap-mmc-highspeed;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +
> +	mmc-pwrseq = <&emmc_pwrseq>;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +&pwm_ef {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_e_pins>;
> +	pinctrl-names = "default";
> +	clocks = <&clkc CLKID_FCLK_DIV4>;
> +	clock-names = "clkin0";
> +};