[PATCH v5 4/5] [media] dt-bindings: add TI VPIF documentation

[khilman@baylibre.com (Kevin Hilman)]

Laurent Pinchart <laurent.pinchart@ideasonboard.com> writes:

> Hi Kevin,
>
> Thank you for the patch.
>
> On Tuesday 06 Dec 2016 21:08:25 Kevin Hilman wrote:
>> Acked-by: Rob Herring <robh@kernel.org>
>> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
>> ---
>> .../devicetree/bindings/media/ti,da850-vpif.txt    | 67 +++++++++++++++++++
>> 1 file changed, 67 insertions(+)
>> create mode 100644
>> Documentation/devicetree/bindings/media/ti,da850-vpif.txt
>> 
>> diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt
>> b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt new file mode
>> 100644
>> index 000000000000..fa06dfdb6898
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt
>> @@ -0,0 +1,67 @@
>> +Texas Instruments VPIF
>> +----------------------
>> +
>> +The TI Video Port InterFace (VPIF) is the primary component for video
>> +capture and display on the DA850/AM18x family of TI DaVinci/Sitara
>> +SoCs.
>> +
>> +TI Document reference: SPRUH82C, Chapter 35
>> +http://www.ti.com/lit/pdf/spruh82
>> +
>> +Required properties:
>> +- compatible: must be "ti,da850-vpif"
>> +- reg: physical base address and length of the registers set for the
>> device;
>> +- interrupts: should contain IRQ line for the VPIF
>> +
>> +Video Capture:
>> +
>> +VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a
>> +single 16-bit channel.  It should contain at least one port child node
>> +with child 'endpoint' node. Please refer to the bindings defined in
>> +Documentation/devicetree/bindings/media/video-interfaces.txt.
>
> You might want to clarify how endpoints are use in the two cases. Apart from 
> that,

OK, I'll add another example for the 16-bit case.  Something like...

>> +Example using 2 8-bit input channels, one of which is connected to an
>> +I2C-connected TVP5147 decoder:
>> +
>> +	vpif: vpif at 217000 {
>> +		compatible = "ti,da850-vpif";
>> +		reg = <0x217000 0x1000>;
>> +		interrupts = <92>;
>> +
>> +		port {
>> +			vpif_ch0: endpoint at 0 {
>> +				  reg = <0>;
>> +				  bus-width = <8>;
>> +				  remote-endpoint = <&composite>;
>> +			};
>> +
>> +			vpif_ch1: endpoint at 1 {
>> +				  reg = <1>;
>> +				  bus-width = <8>;
>> +				  data-shift = <8>;
>> +			};
>> +		};
>> +	};
>> +
>> +[ ... ]
>> +
>> +&i2c0 {
>> +
>> +	tvp5147 at 5d {
>> +		compatible = "ti,tvp5147";
>> +		reg = <0x5d>;
>> +		status = "okay";
>> +
>> +		port {
>> +			composite: endpoint {
>> +				hsync-active = <1>;
>> +				vsync-active = <1>;
>> +				pclk-sample = <0>;
>> +
>> +				/* VPIF channel 0 (lower 8-bits) */
>> +				remote-endpoint = <&vpif_ch0>;
>> +				bus-width = <8>;
>> +			};
>> +		};
>> +	};
>> +};

...this, at the end of the binding doc:

Alternatively, an example when the bus is configured as a single
16-bit input (e.g. for raw-capture mode):

	vpif: vpif at 217000 {
		compatible = "ti,da850-vpif";
		reg = <0x217000 0x1000>;
		interrupts = <92>;

		port {
			vpif_ch0: endpoint {
				  bus-width = <16>;
			};
		};
	};


Thanks for the review,

Kevin