* [LARTC] can't get cbq to traffic shape
@ 2003-06-11 3:32 Trevor Warren
2003-06-11 16:31 ` Stef Coene
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Trevor Warren @ 2003-06-11 3:32 UTC (permalink / raw)
To: lartc
Hello Folks,
For a long time i have tried to get Traffic Shaping work for my 500
Customer setup, but never succeded. I know i have made mistakes which i
ain't able to point out.
I have made a heirarchical setup where in the incoming-outgoing
bandwidth is split into 10 different subnets and i have filters to
divert traffic into these 10 different pipes. Then in each of these
pipes i then have all the clients under those subnets.
Below at the end i have attached the CBQ errors thrown when i
initialise the TC pipes.
Any help and pointers on the same will be appreciated.
Trevor
#####################################
#Deleting and setting up
#Root qdisc's
#####################################
tc qdisc del dev eth0 root
tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 100Mbit avpkt 1000
cell 8
#######################################
#Setting up top 10 qdiscs
#for initial packet classification
#######################################
tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.10.0/24 classid 1:1
tc class add dev eth0 parent 1:0 classid 1:2 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.11.0/24 classid 1:2
tc class add dev eth0 parent 1:0 classid 1:3 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.12.0/24 classid 1:3
tc class add dev eth0 parent 1:0 classid 1:4 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.13.0/24 classid 1:4
tc class add dev eth0 parent 1:0 classid 1:5 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.14.0/24 classid 1:5
tc class add dev eth0 parent 1:0 classid 1:6 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.15.0/24 classid 1:6
tc class add dev eth0 parent 1:0 classid 1:7 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.16.0/24 classid 1:7
tc class add dev eth0 parent 1:0 classid 1:8 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.17.0/24 classid 1:8
tc class add dev eth0 parent 1:0 classid 1:9 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.18.0/24 classid 1:9
tc class add dev eth0 parent 1:0 classid 1:10 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.19.0/24 classid 1:10
tc class add dev eth0 parent 1:0 classid 1:11 cbq bandwidth 10Mbit rate
1Mbit allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.20.0/24 classid 1:11
#################################
# Start of Actual Filters
#################################
tc class add dev eth0 parent 1:1 classid 1:12 cbq bandwidth 10Mbit rate
32Kbit prio 4 allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip prio 4 u32 match ip src
192.168.10.1/0 classid 1:12
# -- -- --
tc class add dev eth0 parent 1:1 classid 1:13 cbq bandwidth 10Mbit rate
32Kbit prio 4 allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip prio 4 u32 match ip src
192.168.10.2/0 classid 1:13
# -- -- --
tc class add dev eth0 parent 1:1 classid 1:14 cbq bandwidth 10Mbit rate
32Kbit prio 4 allot 1514 cell 8 maxburst 20 avpkt 1000
tc filter add dev eth0 parent 1:0 protocol ip prio 4 u32 match ip src
192.168.10.3/0 classid 1:14
#######################
# CBQ Dump
#######################
[root@tuxmania tc_server_code]# dmesg
Q: class 00010152 has bad quantum=0, repaired.
CBQ: class 00010143 has bad quantum=0, repaired.
CBQ: class 00010134 has bad quantum=0, repaired.
CBQ: class 00010125 has bad quantum=0, repaired.
CBQ: class 00010116 has bad quantum=0, repaired.
CBQ: class 00010107 has bad quantum=0, repaired.
CBQ: class 00010071 has bad quantum=0, repaired.
CBQ: class 00010060 has bad quantum=0, repaired.
--
( >- GNU/LINUX, It's all about CHOICE -< )
/~\ __ trevor@clovertechnologies.com __ /~\
| \) / Pre Sales Consultant - Red Hat \ (/ |
|_|_ \ 9820349221(M) | 22881326(O) / _|_|
\___________________________________/
_______________________________________________
LARTC mailing list / LARTC@mailman.ds9a.nl
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [LARTC] can't get cbq to traffic shape
2003-06-11 3:32 [LARTC] can't get cbq to traffic shape Trevor Warren
@ 2003-06-11 16:31 ` Stef Coene
2003-06-12 7:16 ` Trevor Warren
2003-06-12 7:34 ` Trevor Warren
2 siblings, 0 replies; 4+ messages in thread
From: Stef Coene @ 2003-06-11 16:31 UTC (permalink / raw)
To: lartc
On Wednesday 11 June 2003 05:20, Trevor Warren wrote:
> Hello Folks,
>
> For a long time i have tried to get Traffic Shaping work for my 500
> Customer setup, but never succeded. I know i have made mistakes which i
> ain't able to point out.
>
> I have made a heirarchical setup where in the incoming-outgoing
> bandwidth is split into 10 different subnets and i have filters to
> divert traffic into these 10 different pipes. Then in each of these
> pipes i then have all the clients under those subnets.
>
> Below at the end i have attached the CBQ errors thrown when i
> initialise the TC pipes.
>
> Any help and pointers on the same will be appreciated.
The bandwidth _MUST_ be your NIC bandwidth. So it's 100Mbit for a 100mbit
NIC. You combined 100Mbit and 10Mbit.
You also have to provide a weight paramter. Take weight = rate / 10. I think
this will remove the quantum errors.
Some general quesions :
What's you link bandwidth you want to shape? It's best if you add 1 bounded
class to the root qdisc wih rate = link bandwidth and attach all other
classes to that class (and not to the root qdisc).
Is this script used on a firewall? And is eth0 connected to the internet?
Then you have a filter problem. You filter on the src address, but all
connections are natted so the real src address is not known.
Stef
--
stef.coene@docum.org
"Using Linux as bandwidth manager"
http://www.docum.org/
#lartc @ irc.oftc.net
_______________________________________________
LARTC mailing list / LARTC@mailman.ds9a.nl
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [LARTC] can't get cbq to traffic shape
2003-06-11 3:32 [LARTC] can't get cbq to traffic shape Trevor Warren
2003-06-11 16:31 ` Stef Coene
@ 2003-06-12 7:16 ` Trevor Warren
2003-06-12 7:34 ` Trevor Warren
2 siblings, 0 replies; 4+ messages in thread
From: Trevor Warren @ 2003-06-12 7:16 UTC (permalink / raw)
To: lartc
Hello Stef,
Thanks a million for the information. Am sending you the modified tc
script that i worked on. This in essence have 2 filters for the incoming
and outgoing packets to 192.168.*.*.
#!/bin/bash
#####################################
#Deleting and setting up
#Root qdisc's
#####################################
tc qdisc del dev eth0 root
tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 10Mbit avpkt 1000
cell 8
#######################################
#Setting up top 10 qdiscs
#for initial packet classification
#######################################
tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate
200Kbit allot 1514 cell 8 maxburst 20 avpkt 1000 weight 20Kbit bounded
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.10.0/24 classid 1:1
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip dst
192.168.10.0/24 classid 1:1
tc class add dev eth0 parent 1:0 classid 1:2 cbq bandwidth 10Mbit rate
200Kbit allot 1514 cell 8 maxburst 20 avpkt 1000 weight 20Kbit bounded
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.11.0/24 classid 1:2
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip dst
192.168.11.0/24 classid 1:2
tc class add dev eth0 parent 1:0 classid 1:3 cbq bandwidth 10Mbit rate
200Kbit allot 1514 cell 8 maxburst 20 avpkt 1000 weight 20Kbit bounded
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.12.0/24 classid 1:3
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip dst
192.168.12.0/24 classid 1:3
:
:
:
:
####################################
#Actual Filters
####################################
On Wed, 2003-06-11 at 22:01, Stef Coene wrote:
> On Wednesday 11 June 2003 05:20, Trevor Warren wrote:
> > Hello Folks,
> >
> > For a long time i have tried to get Traffic Shaping work for my 500
> > Customer setup, but never succeded. I know i have made mistakes which i
> > ain't able to point out.
> >
> > I have made a heirarchical setup where in the incoming-outgoing
> > bandwidth is split into 10 different subnets and i have filters to
> > divert traffic into these 10 different pipes. Then in each of these
> > pipes i then have all the clients under those subnets.
> >
> > Below at the end i have attached the CBQ errors thrown when i
> > initialise the TC pipes.
> >
> > Any help and pointers on the same will be appreciated.
> The bandwidth _MUST_ be your NIC bandwidth. So it's 100Mbit for a 100mbit
> NIC. You combined 100Mbit and 10Mbit.
> You also have to provide a weight paramter. Take weight = rate / 10. I think
> this will remove the quantum errors.
>
> Some general quesions :
> What's you link bandwidth you want to shape? It's best if you add 1 bounded
> class to the root qdisc wih rate = link bandwidth and attach all other
> classes to that class (and not to the root qdisc).
> Is this script used on a firewall? And is eth0 connected to the internet?
> Then you have a filter problem. You filter on the src address, but all
> connections are natted so the real src address is not known.
>
> Stef
--
( >- GNU/LINUX, It's all about CHOICE -< )
/~\ __ trevor@clovertechnologies.com __ /~\
| \) / Pre Sales Consultant - Red Hat \ (/ |
|_|_ \ 9820349221(M) | 22881326(O) / _|_|
\___________________________________/
_______________________________________________
LARTC mailing list / LARTC@mailman.ds9a.nl
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [LARTC] can't get cbq to traffic shape
2003-06-11 3:32 [LARTC] can't get cbq to traffic shape Trevor Warren
2003-06-11 16:31 ` Stef Coene
2003-06-12 7:16 ` Trevor Warren
@ 2003-06-12 7:34 ` Trevor Warren
2 siblings, 0 replies; 4+ messages in thread
From: Trevor Warren @ 2003-06-12 7:34 UTC (permalink / raw)
To: lartc
Hello Stef,
Thanks a million for the information but things still dont work. Am sending
you the modified tc script that i worked on. This in essence has 2 filters for the incoming
and outgoing packets to 192.168.*.*.
Each location has a 3 server setup.
192.168.0.100 : Billing server (eth0)
x.x.x.x : External IP (eth1)
Other servers :-
192.168.0.101 : Cache server for Network 1
192.168.0.102 : Cache server for Network 2
On the gateway these scripts don't work at all(In terms of Traffic Shaping). Clients are still able
to download more than 40Kbit as suggested in the scripts.
Eth0 is on an internal LAN while eth1, eth2 are external ip addresses. The rule sets in tc
have been made such as to capture traffic and put them between the classes.
This apart, Natting will take place only on the external ethernet adapter right??. Since the Internal
NIC eth0 doesn't have.any Natted conditions it should be easier for it to shape traffic. That apart, one
last but important issue, i am re-directing all web traffic from this gateway load balanced to
the other 2 caching boxes. Can this be an issue??
Awaiting your inputs on the same. Please help me resolve this. You efforts on the same will be appreciated.
#!/bin/bash
#####################################
#Deleting and setting up
#Root qdisc's
#####################################
tc qdisc del dev eth0 root
tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 10Mbit avpkt 1000
cell 8
#######################################
#Setting up top 10 qdiscs
#for initial packet classification
#######################################
tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate
200Kbit allot 1514 cell 8 maxburst 20 avpkt 1000 weight 20Kbit bounded
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.10.0/24 classid 1:1
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip dst
192.168.10.0/24 classid 1:1
tc class add dev eth0 parent 1:0 classid 1:2 cbq bandwidth 10Mbit rate
200Kbit allot 1514 cell 8 maxburst 20 avpkt 1000 weight 20Kbit bounded
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.11.0/24 classid 1:2
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip dst
192.168.11.0/24 classid 1:2
tc class add dev eth0 parent 1:0 classid 1:3 cbq bandwidth 10Mbit rate
200Kbit allot 1514 cell 8 maxburst 20 avpkt 1000 weight 20Kbit bounded
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip src
192.168.12.0/24 classid 1:3
tc filter add dev eth0 parent 1:0 protocol ip u32 match ip dst
192.168.12.0/24 classid 1:3
:
:
:
:
####################################
#Actual Filters
####################################
#################################
# Start of Actual Filters
#################################
tc class add dev eth0 parent 1:1 classid 1:13 cbq bandwidth 10Mbit rate 40Kbit weight 4Kbit prio 4 allot 1514 cell 8 maxburst 20 avpkt 1000 bounded
tc filter add dev eth0 parent 1:1 protocol ip u32 match ip src 192.168.10.1/32 classid 1:13
tc filter add dev eth0 parent 1:1 protocol ip u32 match ip dst 192.168.10.1/32 classid 1:13
tc class add dev eth0 parent 1:1 classid 1:14 cbq bandwidth 10Mbit rate 40Kbit weight 4Kbit prio 4 allot 1514 cell 8 maxburst 20 avpkt 1000 bounded
tc filter add dev eth0 parent 1:1 protocol ip u32 match ip src 192.168.10.2/32 classid 1:14
tc filter add dev eth0 parent 1:1 protocol ip u32 match ip dst 192.168.10.2/32 classid 1:14
:
:
:
:
:
:
Trevor
On Wed, 2003-06-11 at 22:01, Stef Coene wrote:
> On Wednesday 11 June 2003 05:20, Trevor Warren wrote:
> > Hello Folks,
> >
> > For a long time i have tried to get Traffic Shaping work for my 500
> > Customer setup, but never succeded. I know i have made mistakes which i
> > ain't able to point out.
> >
> > I have made a heirarchical setup where in the incoming-outgoing
> > bandwidth is split into 10 different subnets and i have filters to
> > divert traffic into these 10 different pipes. Then in each of these
> > pipes i then have all the clients under those subnets.
> >
> > Below at the end i have attached the CBQ errors thrown when i
> > initialise the TC pipes.
> >
> > Any help and pointers on the same will be appreciated.
> The bandwidth _MUST_ be your NIC bandwidth. So it's 100Mbit for a 100mbit
> NIC. You combined 100Mbit and 10Mbit.
> You also have to provide a weight paramter. Take weight = rate / 10. I think
> this will remove the quantum errors.
>
> Some general quesions :
> What's you link bandwidth you want to shape? It's best if you add 1 bounded
> class to the root qdisc wih rate = link bandwidth and attach all other
> classes to that class (and not to the root qdisc).
> Is this script used on a firewall? And is eth0 connected to the internet?
> Then you have a filter problem. You filter on the src address, but all
> connections are natted so the real src address is not known.
>
> Stef
--
( >- GNU/LINUX, It's all about CHOICE -< )
/~\ __ trevor@clovertechnologies.com __ /~\
| \) / Pre Sales Consultant - Red Hat \ (/ |
|_|_ \ 9820349221(M) | 22881326(O) / _|_|
\___________________________________/
_______________________________________________
LARTC mailing list / LARTC@mailman.ds9a.nl
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2003-06-12 7:34 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2003-06-11 3:32 [LARTC] can't get cbq to traffic shape Trevor Warren
2003-06-11 16:31 ` Stef Coene
2003-06-12 7:16 ` Trevor Warren
2003-06-12 7:34 ` Trevor Warren
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.