From: Pierre JUHEN <pierre.juhen@wanadoo.fr>
To: linux-hotplug@vger.kernel.org
Subject: PROBLEM : PCI hotplug crashes with 2.4.9
Date: Mon, 20 Aug 2001 19:33:43 +0000 [thread overview]
Message-ID: <marc-linux-hotplug-99833581003509@msgid-missing> (raw)
[1.] PCI hotplug crashes with 2.4.9
[2.] hotplug causes the system to crash with kernel 2.4.9 (same
configuration with 2.4.6 was OK). A manual run of
"/etc/rc.d/init.d/hotplug start" shows that the system crashes
immediatly when the system starts to scan the PCI devices. Only the
first line "pcimodules scanning 00:00.0" is displayed. No trace is
written in /var/log/messages.
[3.] PCI hotplug kernel
[4.] Linux version 2.4.9 (root@pierre.juhen) (gcc version 2.96 20000731
(Red Hat Linux 7.1 2.96-81)) #2 dim aoû 19 19:02:56 CEST 2001
[5.]
[6.] /etc/hotplug/pci.rc start
[7.]
[7.1] Software
Linux pierre.juhen 2.4.9 #2 dim aoû 19 19:02:56 CEST 2001 i686 unknown
Gnu C 2.96
Gnu make 3.79.1
binutils 2.10.91.0.2
util-linux 2.10s
mount 2.11b
modutils 2.4.2
e2fsprogs 1.19
reiserfsprogs 3.x.0b
pcmcia-cs 3.1.19
PPP 2.4.0
isdn4k-utils 3.1pre1
Linux C Library 2.2.2
Dynamic linker (ldd) 2.2.2
Procps 2.0.7
Net-tools 1.56
Console-tools 0.3.3
Sh-utils 2.0
[7.2] Processor
processor : 0
vendor_id : GenuineIntel
cpu family : 6
model : 5
model name : Pentium II (Deschutes)
stepping : 2
cpu MHz : 400.914
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca
cmov pat pse36 mmx fxsr
bogomips : 799.53
[7.3] modules
pppoatm 2832 1
ppp_generic 14816 3 [pppoatm]
slhc 5024 0 [ppp_generic]
usb-uhci 21088 0 (unused)
speedtch 11568 3
snd-seq-midi 3600 0 (unused)
snd-seq-midi-event 3264 0 [snd-seq-midi]
snd-seq 41792 0 [snd-seq-midi snd-seq-midi-event]
snd-card-ens1371 2288 0
snd-ens1371 9664 0 [snd-card-ens1371]
snd-rawmidi 10080 0 [snd-seq-midi snd-ens1371]
snd-seq-device 4016 0 [snd-seq-midi snd-seq snd-rawmidi]
snd-pcm 31520 0 [snd-ens1371]
snd-timer 8560 0 [snd-seq snd-pcm]
snd-ac97-codec 25024 0 [snd-ens1371]
snd-mixer 24608 0 [snd-ens1371 snd-ac97-codec]
snd 34896 1 [snd-seq-midi snd-seq-midi-event
snd-seq snd-card-ens1371 snd-ens1371 snd-rawmidi snd-seq-device snd-pcm
snd-timer snd-ac97-codec snd-mixer]
soundcore 4144 2 [snd]
3c509 6224 1 (autoclean)
ipchains 35904 0 (unused)
nls_iso8859-1 2880 1 (autoclean)
nls_cp437 4384 1 (autoclean)
vfat 9424 1 (autoclean)
fat 32320 0 (autoclean) [vfat]
usbcore 50272 1 [usb-uhci speedtch]
[7.4] iomem / ioports
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000cdfff : Extension ROM
000f0000-000fffff : System ROM
00100000-07feffff : System RAM
00100000-001fb813 : Kernel code
001fb814-00257b7f : Kernel data
07ff0000-07ff2fff : ACPI Non-volatile Storage
07ff3000-07ffffff : ACPI Tables
d8000000-dbffffff : Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
dc000000-deffffff : PCI Bus #01
dc000000-dc003fff : Matrox Graphics, Inc. MGA G200 AGP
dd000000-dd7fffff : Matrox Graphics, Inc. MGA G200 AGP
df000000-dfffffff : PCI Bus #01
df000000-dfffffff : Matrox Graphics, Inc. MGA G200 AGP
e1000000-e1003fff : PCI device 104c:8020 (Texas Instruments)
e1004000-e1004fff : Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895
e1004000-e1004fff : aic7xxx
e1005000-e10057ff : PCI device 104c:8020 (Texas Instruments)
e1006000-e1006fff : Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 (#2)
e1006000-e1006fff : aic7xxx
ffff0000-ffffffff : reserved
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
01f0-01f7 : ide0
0280-028f : 3c509
02f8-02ff : serial(auto)
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
4000-403f : Intel Corporation 82371AB PIIX4 ACPI
5000-501f : Intel Corporation 82371AB PIIX4 ACPI
e000-e01f : Intel Corporation 82371AB PIIX4 USB
e000-e01f : usb-uhci
e400-e43f : Ensoniq ES1371 [AudioPCI-97]
e400-e43f : Ensoniq AudioPCI
e800-e8ff : Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895
ec00-ecff : Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 (#2)
f000-f00f : Intel Corporation 82371AB PIIX4 IDE
[7.5] PCI
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge
(rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR+
Latency: 32
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge
(rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dc000000-deffffff
Prefetchable memory behind bridge: df000000-dfffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01)
(prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at f000 [size=16]
00:07.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01)
(prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at e000 [size=32]
00:07.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:0f.0 FireWire (IEEE 1394): Texas Instruments: Unknown device 8020
(prog-if 10 [OHCI])
Subsystem: Pinnacle Systems Inc.: Unknown device 000e
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: Memory at e1005000 (32-bit, non-prefetchable)
[size=2K]
Region 1: Memory at e1000000 (32-bit, non-prefetchable)
[size=16K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev
02)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V,
AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort+ <MAbort+ >SERR- <PERR-
Latency: 64 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e400 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.0 SCSI storage controller: Adaptec AHA-2940U/UW / AHA-39xx /
AIC-7895 (rev 04)
Subsystem: Adaptec AHA-2940U/2940UW Dual AHA-394xAU/AUW/AUWD
AIC-7895B
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800 [disabled] [size=256]
Region 1: Memory at e1004000 (32-bit, non-prefetchable)
[size=4K]
Expansion ROM at e0000000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:14.1 SCSI storage controller: Adaptec AHA-2940U/UW / AHA-39xx /
AIC-7895 (rev 04)
Subsystem: Adaptec AHA-2940U/2940UW Dual AHA-394xAU/AUW/AUWD
AIC-7895B
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 2000ns max)
Interrupt: pin B routed to IRQ 15
Region 0: I/O ports at ec00 [disabled] [size=256]
Region 1: Memory at e1006000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP
(rev 01) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. MGA-G200 AGP
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 8000ns max), cache line size 08
Interrupt: pin A routed to IRQ 15
Region 0: Memory at df000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at dc000000 (32-bit, non-prefetchable)
[size=16K]
Region 2: Memory at dd000000 (32-bit, non-prefetchable)
[size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 1.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x2
[7.6] SCSI
Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: MATSHITA Model: CD-R CW-7502 Rev: 4.10
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: IBM Model: DDRS-34560W Rev: S97B
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 10 Lun: 00
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
[7.7] hotplug version : hotplug-2001_04_24-1_7.x (binary RPM)
[8.] Workaround : rename /etc/hotplug/pci.rc for example with
/etc/hotplug/pci.not-rc. This disable PCI hotplug but keeps
USB hotplugging
_______________________________________________
Linux-hotplug-devel mailing list http://linux-hotplug.sourceforge.net
Linux-hotplug-devel@lists.sourceforge.net
http://lists.sourceforge.net/lists/listinfo/linux-hotplug-devel
next reply other threads:[~2001-08-20 19:33 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-08-20 19:33 Pierre JUHEN [this message]
2001-08-20 19:36 ` PROBLEM : PCI hotplug crashes with 2.4.9 Greg KH
2001-08-20 22:50 ` David Brownell
2001-08-21 18:04 ` Pierre JUHEN
2001-08-21 18:22 ` David Brownell
2001-08-21 21:09 ` Pierre JUHEN
-- strict thread matches above, loose matches on Subject: below --
2001-08-20 19:33 Pierre JUHEN
2001-08-20 19:36 ` Greg KH
2001-08-20 22:50 ` David Brownell
2001-08-21 18:04 ` Pierre JUHEN
2001-08-21 18:22 ` David Brownell
2001-08-21 21:09 ` Pierre JUHEN
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=marc-linux-hotplug-99833581003509@msgid-missing \
--to=pierre.juhen@wanadoo.fr \
--cc=linux-hotplug@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.