All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH 1/2 (for-next)] ARM: OMAP3: Add support for the IGEP v2 board (rev B)
@ 2009-11-13 12:29 Enric Balletbo i Serra
  2009-11-13 12:29 ` [PATCH 2/2 (for-next)] ARM: OMAP3: Add defconfig for IGEP v2 board Enric Balletbo i Serra
  2009-11-14  0:48 ` [APPLIED] [PATCH 1/2 (for-next)] ARM: OMAP3: Add support for the IGEP v2 Tony Lindgren
  0 siblings, 2 replies; 4+ messages in thread
From: Enric Balletbo i Serra @ 2009-11-13 12:29 UTC (permalink / raw)
  To: linux-omap; +Cc: Enric Balletbo i Serra

From: Enric Balletbo i Serra <eballetbo@iseebcn.com>

This patch adds minimal IGEP v2 support.

The IGEP v2 board is a low-cost, fan-less and industrial temperature
range single board computer that unleashes laptop-like performance and
expandability without the bulk, expense, or noise of typical desktop
machines. Its architecture shares much in common with other OMAP3 boards.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
---
 arch/arm/mach-omap2/Kconfig          |    4 +
 arch/arm/mach-omap2/Makefile         |    2 +
 arch/arm/mach-omap2/board-igep0020.c |  251 ++++++++++++++++++++++++++++++++++
 3 files changed, 257 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-omap2/board-igep0020.c

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 35b7f5c..b25af76 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -113,6 +113,10 @@ config MACH_OMAP_3630SDP
 	bool "OMAP3630 SDP board"
 	depends on ARCH_OMAP3 && ARCH_OMAP34XX
 
+config MACH_IGEP0020
+	bool "IGEP0020"
+	depends on ARCH_OMAP3 && ARCH_OMAP34XX
+
 config MACH_OMAP_4430SDP
 	bool "OMAP 4430 SDP board"
 	depends on ARCH_OMAP4
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index fd7198e..59b0ccc 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -88,6 +88,8 @@ obj-$(CONFIG_MACH_OMAP_3630SDP)		+= board-3630sdp.o \
 					   mmc-twl4030.o
 obj-$(CONFIG_MACH_CM_T35)		+= board-cm-t35.o \
 					   mmc-twl4030.o
+obj-$(CONFIG_MACH_IGEP0020)		+= board-igep0020.o \
+					   mmc-twl4030.o
 
 obj-$(CONFIG_MACH_OMAP_4430SDP)		+= board-4430sdp.o
 
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
new file mode 100644
index 0000000..fa62e80
--- /dev/null
+++ b/arch/arm/mach-omap2/board-igep0020.c
@@ -0,0 +1,251 @@
+/*
+ * Copyright (C) 2009 Integration Software and Electronic Engineering.
+ *
+ * Modified from mach-omap2/board-generic.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+
+#include <linux/regulator/machine.h>
+#include <linux/i2c/twl4030.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include <plat/board.h>
+#include <plat/common.h>
+#include <plat/gpmc.h>
+#include <plat/mux.h>
+#include <plat/usb.h>
+
+#include "mmc-twl4030.h"
+
+#define IGEP2_SMSC911X_CS       5
+#define IGEP2_SMSC911X_GPIO     176
+#define IGEP2_GPIO_USBH_NRESET  24
+#define IGEP2_GPIO_LED0_RED 	26
+#define IGEP2_GPIO_LED0_GREEN 	27
+#define IGEP2_GPIO_LED1_RED   	28
+
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+
+#include <linux/smsc911x.h>
+
+static struct smsc911x_platform_config igep2_smsc911x_config = {
+	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS  ,
+	.phy_interface	= PHY_INTERFACE_MODE_MII,
+};
+
+static struct resource igep2_smsc911x_resources[] = {
+	{
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= OMAP_GPIO_IRQ(IGEP2_SMSC911X_GPIO),
+		.end	= OMAP_GPIO_IRQ(IGEP2_SMSC911X_GPIO),
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
+	},
+};
+
+static struct platform_device igep2_smsc911x_device = {
+	.name		= "smsc911x",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(igep2_smsc911x_resources),
+	.resource	= igep2_smsc911x_resources,
+	.dev		= {
+		.platform_data = &igep2_smsc911x_config,
+	},
+};
+
+static inline void __init igep2_init_smsc911x(void)
+{
+	unsigned long cs_mem_base;
+
+	if (gpmc_cs_request(IGEP2_SMSC911X_CS, SZ_16M, &cs_mem_base) < 0) {
+		pr_err("IGEP v2: Failed request for GPMC mem for smsc911x\n");
+		gpmc_cs_free(IGEP2_SMSC911X_CS);
+		return;
+	}
+
+	igep2_smsc911x_resources[0].start = cs_mem_base + 0x0;
+	igep2_smsc911x_resources[0].end   = cs_mem_base + 0xff;
+
+	if ((gpio_request(IGEP2_SMSC911X_GPIO, "SMSC911X IRQ") == 0) &&
+	    (gpio_direction_input(IGEP2_SMSC911X_GPIO) == 0)) {
+		gpio_export(IGEP2_SMSC911X_GPIO, 0);
+	} else {
+		pr_err("IGEP v2: Could not obtain gpio for for SMSC911X IRQ\n");
+		return;
+	}
+
+	platform_device_register(&igep2_smsc911x_device);
+}
+
+#else
+static inline void __init igep2_init_smsc911x(void) { }
+#endif
+
+static struct omap_board_config_kernel igep2_config[] __initdata = {
+};
+
+static struct regulator_consumer_supply igep2_vmmc1_supply = {
+	.supply		= "vmmc",
+};
+
+/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
+static struct regulator_init_data igep2_vmmc1 = {
+	.constraints = {
+		.min_uV			= 1850000,
+		.max_uV			= 3150000,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
+					| REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = 1,
+	.consumer_supplies      = &igep2_vmmc1_supply,
+};
+
+static struct twl4030_hsmmc_info mmc[] = {
+	{
+		.mmc		= 1,
+		.wires		= 4,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
+	},
+	{
+		.mmc		= 2,
+		.wires		= 4,
+		.gpio_cd	= -EINVAL,
+		.gpio_wp	= -EINVAL,
+	},
+	{}      /* Terminator */
+};
+
+static int igep2_twl_gpio_setup(struct device *dev,
+		unsigned gpio, unsigned ngpio)
+{
+	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
+	mmc[0].gpio_cd = gpio + 0;
+	twl4030_mmc_init(mmc);
+
+	/* link regulators to MMC adapters ... we "know" the
+	 * regulators will be set up only *after* we return.
+	*/
+	igep2_vmmc1_supply.dev = mmc[0].dev;
+
+	return 0;
+};
+
+static struct twl4030_gpio_platform_data igep2_gpio_data = {
+	.gpio_base	= OMAP_MAX_GPIO_LINES,
+	.irq_base	= TWL4030_GPIO_IRQ_BASE,
+	.irq_end	= TWL4030_GPIO_IRQ_END,
+	.use_leds	= false,
+	.setup		= igep2_twl_gpio_setup,
+};
+
+static struct twl4030_usb_data igep2_usb_data = {
+	.usb_mode	= T2_USB_MODE_ULPI,
+};
+
+static void __init igep2_init_irq(void)
+{
+	omap_board_config = igep2_config;
+	omap_board_config_size = ARRAY_SIZE(igep2_config);
+	omap2_init_common_hw(NULL, NULL);
+	omap_init_irq();
+	omap_gpio_init();
+}
+
+static struct twl4030_platform_data igep2_twldata = {
+	.irq_base	= TWL4030_IRQ_BASE,
+	.irq_end	= TWL4030_IRQ_END,
+
+	/* platform_data for children goes here */
+	.usb		= &igep2_usb_data,
+	.gpio		= &igep2_gpio_data,
+	.vmmc1          = &igep2_vmmc1,
+
+};
+
+static struct i2c_board_info __initdata igep2_i2c_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("twl4030", 0x48),
+		.flags		= I2C_CLIENT_WAKE,
+		.irq		= INT_34XX_SYS_NIRQ,
+		.platform_data	= &igep2_twldata,
+	},
+};
+
+static int __init igep2_i2c_init(void)
+{
+	omap_register_i2c_bus(1, 2600, igep2_i2c_boardinfo,
+			ARRAY_SIZE(igep2_i2c_boardinfo));
+	/* Bus 3 is attached to the DVI port where devices like the pico DLP
+	 * projector don't work reliably with 400kHz */
+	omap_register_i2c_bus(3, 100, NULL, 0);
+	return 0;
+}
+
+static void __init igep2_init(void)
+{
+	igep2_i2c_init();
+	omap_serial_init();
+	usb_musb_init();
+
+	igep2_init_smsc911x();
+
+	/* GPIO userspace leds */
+	if ((gpio_request(IGEP2_GPIO_LED0_RED, "GPIO_LED0_RED") == 0) &&
+	    (gpio_direction_output(IGEP2_GPIO_LED0_RED, 1) == 0)) {
+		gpio_export(IGEP2_GPIO_LED0_RED, 0);
+		gpio_set_value(IGEP2_GPIO_LED0_RED, 0);
+	} else
+		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_RED\n");
+
+	if ((gpio_request(IGEP2_GPIO_LED0_GREEN, "GPIO_LED0_GREEN") == 0) &&
+	    (gpio_direction_output(IGEP2_GPIO_LED0_GREEN, 1) == 0)) {
+		gpio_export(IGEP2_GPIO_LED0_GREEN, 0);
+		gpio_set_value(IGEP2_GPIO_LED0_GREEN, 0);
+	} else
+		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_GREEN\n");
+
+	if ((gpio_request(IGEP2_GPIO_LED1_RED, "GPIO_LED1_RED") == 0) &&
+	    (gpio_direction_output(IGEP2_GPIO_LED1_RED, 1) == 0)) {
+		gpio_export(IGEP2_GPIO_LED1_RED, 0);
+		gpio_set_value(IGEP2_GPIO_LED1_RED, 0);
+	} else
+		pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
+}
+
+static void __init igep2_map_io(void)
+{
+	omap2_set_globals_343x();
+	omap2_map_common_io();
+}
+
+MACHINE_START(IGEP0020, "IGEP v2 board")
+	.phys_io	= 0x48000000,
+	.io_pg_offst	= ((0xfa000000) >> 18) & 0xfffc,
+	.boot_params	= 0x80000100,
+	.map_io		= igep2_map_io,
+	.init_irq	= igep2_init_irq,
+	.init_machine	= igep2_init,
+	.timer		= &omap_timer,
+MACHINE_END
-- 
1.5.4.3


^ permalink raw reply related	[flat|nested] 4+ messages in thread
end of thread, other threads:[~2009-11-14  0:49 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-11-13 12:29 [PATCH 1/2 (for-next)] ARM: OMAP3: Add support for the IGEP v2 board (rev B) Enric Balletbo i Serra
2009-11-13 12:29 ` [PATCH 2/2 (for-next)] ARM: OMAP3: Add defconfig for IGEP v2 board Enric Balletbo i Serra
2009-11-14  0:49   ` [APPLIED] " Tony Lindgren
2009-11-14  0:48 ` [APPLIED] [PATCH 1/2 (for-next)] ARM: OMAP3: Add support for the IGEP v2 Tony Lindgren

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.