[PATCH v5 0/2] Add device tree for Acer Swift Go Pro AI (SFA14-11)

[PATCH v5 0/2] Add device tree for Acer Swift Go Pro AI (SFA14-11)

[Kaipeng Zeng]

The work started with x1-crd.dtsi as initial template.
HDMI refers to ThinkPad T14s.
Bluetooth refers to x1-crd.dtsi from the ubuntu-concept kernel [1].
PWM brightness control refers to Ratizux's GitHub repository [2].

Tested on linux-next (next-20261021: 9a482184) / Ubuntu 26.04 LTS.

Tested and working devices:
 - NVMe
 - Keyboard & Touchpad
 - USB Type-A, Type-C
 - Battery & charging status
 - Internal display & Backlight brightness control
 - HDMI & Type-C display (with audio)
 - Bluetooth & Wi-Fi
 - Webcam (usb_2)
 - GPU
 - Audio: speaker (partial), mic, headphone.

Known issues:
- Four internal speakers are detected, but only three work. I use Ratizux's tplg [3] and
  alsa configuration [4] on my desktop. I also use amixer & speaker-test to verify them.
- EL2-mode:
  - EL2-mode can only work with kernel parameter: "iommu.passthrough=1".
  - Audio and Battery status are broken under EL2 mode.
  - Bluetooth is broken under EL2 mode.

Also, some notes about eusb*_repeater and EC; hopefully, this can help others understand
why I configured these nodes this way:
- eusb*_repeater conflict between the DSDT and my testing:
  By using `i2ctransfer` to sequentially set the modes of 'eusb3/5/6_repeater', I can
  observe the corresponding connection or disconnection state changes for the
  right-side USB-A port ('usb_mp_hsphy0'), the left-side USB-A port ('usb_mp_hsphy1'),
  and the webcam ('usb_2'). Using `gpioset`, it can be verified that 'eusb6_repeater'
  is affected by tlmm's GPIO 184, while setting GPIO 6/7 has no effect. And webcam
  can be shut down and reset by toggling GPIO 184. The DSDT places GPIO 6/184 as a
  'ResourceTemplate' under 'USB3'(usb_mp), GPIO 7 under USB4(usb_2), and webcam is
  under USB4. This conflicts with my testing. So, I didn't add the unverified GPIO,
  and the connection between USB and repeater follows my testing rather than DSDT.
- There is an EC device under i2c5 at address 0x76, with driver probe failed.
  But using i2ctransfer I can observe some data changes related to fan.
  The EC driver appears to require additional work, and it couldn't be included in
  this patch. So, I didn't add that node.

[1] https://git.launchpad.net/~ubuntu-concept/ubuntu/+source/linux/+git/resolute
[2] https://github.com/Ratizux/linux-device-acer-sfa14-11.git
[3] https://github.com/Ratizux/audioreach-topology/
[4] https://github.com/Ratizux/alsa-ucm-conf

---
Changelog:

V5:
- Rebase to next-20261021, pick up the following upstream changes:
    arm64: dts: qcom: x1-crd: Mark the EC reset gpio as reserved (099cd579).
    arm64: dts: qcom: hamoa/purwa: Add QREF regulator supplies (d9d07e23).
    arm64: dts: qcom: hamoa: Fix swapped USB QMP PHY vdda-phy/vdda-pll supplies (4458dcd3).
- Add 'eusb*_repeater'. (Jianfeng Liu)
- Add 'displayport-2-dai-link'. (Jianfeng Liu)
- Remove 'usb_1_ss1' and 'mdss_dp1'. (Jianfeng Liu)
- Remove unused 'audio-routing'. (Jianfeng Liu)
- Remove 'kypd_vol_up_n'. (Jianfeng Liu)

V4:
- Add -el2-dtbs. (Sashiko)
- The "audio-routing" of "sound" is from x1-crd.dtsi, audio doesn't totally work,
  and I didn't see any improvements when I followed Sashiko's advice,
  so I just kept it the same as x1-crd.dtsi. (Sashiko)
- Tested in EL2 mode:
  Successfully boots with the kernel parameter: "iommu.passthrough=1",
  The above features work as in EL1 mode except battery status.
- Fix missing newline before "wsa-dai-link". (Val Packett)
- Link to V4: https://lore.kernel.org/linux-devicetree/20261006085425.40450-1-kaipeng94@gmail.com/

V3:
- Re-sort *-link and its sub-nodes. (Konrad Dybcio)
- Keep a '\n' before 'status'. (Konrad Dybcio)
- Remove 'output-low' from wcd_default. (Konrad Dybcio)
- Link to V3: https://lore.kernel.org/linux-devicetree/20260729064538.19564-1-kaipeng94@gmail.com/

V2:
- Fix Makefile entry ordering. (Krzysztof Kozlowski)
- Use readable compatible string. (Krzysztof Kozlowski)
- Fix sound card model name for this device. (Krzysztof Kozlowski & Konrad Dybcio)
- Re-sort nodes, pinctrl-*. (Krzysztof Kozlowski & Konrad Dybcio)
- Remove those regulators without consumer and lack of a required value in DSDT. (Konrad Dybcio)
- Remove ADSP/CDSP fastrpc memory. (Konrad Dybcio)
- Add iris firmware path. (Konrad Dybcio)
- Delete usb_1_ss1_qmpphy/usb_1_ss2_qmpphy properties of Type-C. (Sashiko)
- Delete usb_1_ss2_hsphy. (Sashiko)
- Remove unused pmic-glink orientation-gpio. (Sashiko)
- Remove node related to WWAN.

- The Webcam is a USB device, can be probed without any additional
  node. (Sashiko)
- Using reset-gpios in swr* seems common in X1E devices, like Lenovo
  Yoga Slim7x, ThinkPad t14s and Microsoft Romulus.
  Because speakers do not completely work and I could not see any
  effect of changing it, just retain it. (Sashiko)
- Also, the HDMI audio is the same reason as above. (Sashiko)
- Link to V2: https://lore.kernel.org/linux-devicetree/20260721082410.18275-1-kaipeng94@gmail.com/

- Link to V1: https://lore.kernel.org/linux-devicetree/20260702063156.35169-1-kaipeng94@gmail.com/

Kaipeng Zeng (2):
  dt-bindings: arm: qcom: Add Acer Swift Go Pro AI (SFA14-11)
  arm64: dts: qcom: Add support for Acer Swift Go Pro AI (SFA14-11)

 .../devicetree/bindings/arm/qcom.yaml         |    1 +
 arch/arm64/boot/dts/qcom/Makefile             |    2 +
 .../boot/dts/qcom/x1e78100-acer-sfa14-11.dts  | 1541 +++++++++++++++++
 3 files changed, 1544 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/x1e78100-acer-sfa14-11.dts


base-commit: 9a482184d910775cf648863148944945b74e2815
-- 
2.53.0

[PATCH v5 1/2] dt-bindings: arm: qcom: Add Acer Swift Go Pro AI (SFA14-11)

[Kaipeng Zeng]

Add Acer Swift Go Pro AI (SFA14-11), a laptop based on the Snapdragon X
Elite (X1E78100) SoC.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Kaipeng Zeng <kaipeng94@gmail.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 121ca557ce1e..027207758cab 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1240,6 +1240,7 @@ properties:
 
       - items:
           - enum:
+              - acer,swift-go-sfa14-11
               - medion,sprchrgd14s1
               - tuxedo,elite14gen1
           - const: qcom,x1e78100
-- 
2.53.0

[PATCH v5 2/2] arm64: dts: qcom: Add support for Acer Swift Go Pro AI (SFA14-11)

[Kaipeng Zeng]

Introduce device tree for the Acer Swift Go Pro AI (SFA14-11).
It is a laptop based on the Qualcomm Snapdragon X Elite (X1E78100) SoC.
This device tree implementation references nodes from the x1-crd.dtsi.

Supported features:

 - Internal display & Brightness control
 - Keyboard & Touchpad
 - USB Type-C, Type-A
 - Wi-Fi & Bluetooth
 - ADSP & CDSP
 - Adreno X1-85 GPU
 - HDMI & USB Type-C display
 - Webcam
 - Audio

Signed-off-by: Kaipeng Zeng <kaipeng94@gmail.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |    2 +
 .../boot/dts/qcom/x1e78100-acer-sfa14-11.dts  | 1541 +++++++++++++++++
 2 files changed, 1543 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/x1e78100-acer-sfa14-11.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 88230c4e00ea..142d8452e429 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -473,6 +473,8 @@ talos-evk-rpi-display-2-5in-dtbs	:= \
 dtb-$(CONFIG_ARCH_QCOM)	+= talos-evk-rpi-display-2-5in.dtb
 x1e001de-devkit-el2-dtbs	:= x1e001de-devkit.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e001de-devkit.dtb x1e001de-devkit-el2.dtb
+x1e78100-acer-sfa14-11-el2-dtbs	:= x1e78100-acer-sfa14-11.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= x1e78100-acer-sfa14-11.dtb x1e78100-acer-sfa14-11-el2.dtb
 x1e78100-lenovo-thinkpad-t14s-el2-dtbs	:= x1e78100-lenovo-thinkpad-t14s.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e78100-lenovo-thinkpad-t14s.dtb x1e78100-lenovo-thinkpad-t14s-el2.dtb
 x1e78100-lenovo-thinkpad-t14s-oled-el2-dtbs	:= x1e78100-lenovo-thinkpad-t14s-oled.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/x1e78100-acer-sfa14-11.dts b/arch/arm64/boot/dts/qcom/x1e78100-acer-sfa14-11.dts
new file mode 100644
index 000000000000..5814cf3d000c
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1e78100-acer-sfa14-11.dts
@@ -0,0 +1,1541 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2026, Kaipeng Zeng <kaipeng94@gmail.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "hamoa.dtsi"
+#include "hamoa-pmics.dtsi"
+
+/ {
+	model = "Acer Swift Go Pro AI (SFA14-11)";
+	compatible = "acer,swift-go-sfa14-11", "qcom,x1e78100", "qcom,x1e80100";
+
+	aliases {
+		serial0 = &uart21;
+		serial1 = &uart14;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-0 = <&wcd_default>;
+		pinctrl-names = "default";
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+
+		#sound-dai-cells = <1>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		pwms = <&pm8550_pwm 3 5000000>;
+
+		brightness-levels = <254 225 200 175 150 125 100 75 65 60 55>;
+		default-brightness-level = <8>;
+
+		power-supply = <&vreg_edp_bl>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&hall_int_n_default>;
+		pinctrl-names = "default";
+
+		switch-lid {
+			label = "lid";
+			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+		};
+	};
+
+	hdmi-bridge {
+		compatible = "realtek,rtd2171";
+
+		pinctrl-0 = <&hdmi_hpd_default>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				hdmi_bridge_dp_in: endpoint {
+					remote-endpoint = <&usb_1_ss2_qmpphy_out_dp>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				hdmi_bridge_tmds_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&hdmi_bridge_tmds_out>;
+			};
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+			     "qcom,sm8550-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>;
+
+		nvmem-cells = <&charge_limit_en>,
+			      <&charge_limit_end>,
+			      <&charge_limit_delta>;
+		nvmem-cell-names = "charge_limit_en",
+				   "charge_limit_end",
+				   "charge_limit_delta";
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&retimer_ss0_ss_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_con_sbu_in: endpoint {
+						remote-endpoint = <&retimer_ss0_con_sbu_out>;
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x0 0x8000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+	sound {
+		compatible = "qcom,x1e80100-sndcard";
+		model = "X1E78100-ACER-Swift-Go-SFA14-11";
+		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
+				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
+				"WooferRight IN", "WSA2 WSA_SPK1 OUT",
+				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
+				"IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"VA DMIC0", "MIC BIAS3",
+				"VA DMIC1", "MIC BIAS3",
+				"TX SWR_INPUT1", "ADC2_OUTPUT";
+
+		displayport-0-dai-link {
+			link-name = "DisplayPort0 Playback";
+
+			codec {
+				sound-dai = <&mdss_dp0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai DISPLAY_PORT_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		displayport-2-dai-link {
+			link-name = "DisplayPort2 Playback";
+
+			codec {
+				sound-dai = <&mdss_dp2>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai DISPLAY_PORT_RX_2>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			codec {
+				sound-dai = <&left_woofer>, <&left_tweeter>,
+					    <&swr0 0>, <&lpass_wsamacro 0>,
+					    <&right_woofer>, <&right_tweeter>,
+					    <&swr3 0>, <&lpass_wsa2macro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-always-on;
+	};
+
+	vreg_edp_bl: regulator-edp-bl {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VBL9";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_MISC_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&misc_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+
+		gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_pwr_1p15_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_1P8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_1p8_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_RTMR0_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&usb0_3p3_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_1p9: regulator-wcn-1p9 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_1P9";
+		regulator-min-microvolt = <1900000>;
+		regulator-max-microvolt = <1900000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		vdd-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_wcn_0p95>;
+		vdddig-supply = <&vreg_wcn_0p95>;
+		vddrfa1p2-supply = <&vreg_wcn_1p9>;
+		vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_wlan_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob2>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l12-supply = <&vreg_s5j_1p2>;
+		vdd-l15-supply = <&vreg_s4c_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_1p8: ldo4 {
+			regulator-name = "vreg_l4b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_3p0: ldo8 {
+			regulator-name = "vreg_l8b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p2: ldo12 {
+			regulator-name = "vreg_l12b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p0: ldo14 {
+			regulator-name = "vreg_l14b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4c_1p8: smps4 {
+			regulator-name = "vreg_s4c_1p8";
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c_1p2: ldo1 {
+			regulator-name = "vreg_l1c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_0p8: ldo2 {
+			regulator-name = "vreg_l2c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_0p8: ldo3 {
+			regulator-name = "vreg_l3c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s4c_1p8>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_l1d_0p8: ldo1 {
+			regulator-name = "vreg_l1d_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p9: ldo2 {
+			regulator-name = "vreg_l2d_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3d_1p8: ldo3 {
+			regulator-name = "vreg_l3d_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_s1f_0p7: smps1 {
+			regulator-name = "vreg_s1f_0p7";
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "i";
+
+		vdd-l1-supply = <&vreg_s4c_1p8>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+
+		vreg_s1i_0p9: smps1 {
+			regulator-name = "vreg_s1i_0p9";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2i_1p0: smps2 {
+			regulator-name = "vreg_s2i_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1i_1p8: ldo1 {
+			regulator-name = "vreg_l1i_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3i_0p8: ldo3 {
+			regulator-name = "vreg_l3i_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "j";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s5j_1p2: smps5 {
+			regulator-name = "vreg_s5j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1j_0p8: ldo1 {
+			regulator-name = "vreg_l1j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2j_1p2: ldo2 {
+			regulator-name = "vreg_l2j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3j_0p8: ldo3 {
+			regulator-name = "vreg_l3j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/x1e80100/ACER/SFA14-11/qcdxkmsuc8380.mbn";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+
+		hid-descr-addr = <0x20>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		pinctrl-0 = <&tpad_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+
+		hid-descr-addr = <0x01>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		pinctrl-0 = <&kybd_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	typec-mux@8 {
+		compatible = "parade,ps8830";
+		reg = <0x08>;
+
+		clocks = <&rpmhcc RPMH_RF_CLK3>;
+
+		vdd-supply = <&vreg_rtmr0_1p15>;
+		vdd33-supply = <&vreg_rtmr0_3p3>;
+		vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+		vddar-supply = <&vreg_rtmr0_1p15>;
+		vddat-supply = <&vreg_rtmr0_1p15>;
+		vddio-supply = <&vreg_rtmr0_1p8>;
+
+		reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&rtmr0_default>;
+		pinctrl-names = "default";
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				retimer_ss0_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				retimer_ss0_ss_in: endpoint {
+					remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				retimer_ss0_con_sbu_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	eusb3_repeater: redriver@47 {
+		compatible = "nxp,ptn3222";
+		reg = <0x47>;
+
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+
+		#phy-cells = <0>;
+	};
+
+	eusb5_repeater: redriver@4b {
+		compatible = "nxp,ptn3222";
+		reg = <0x4b>;
+
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+
+		#phy-cells = <0>;
+	};
+
+	eusb6_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+
+		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb6_reset_n>;
+		pinctrl-names = "default";
+
+		#phy-cells = <0>;
+	};
+};
+
+&iris {
+	firmware-name = "qcom/x1e80100/ACER/SFA14-11/qcvss8380.mbn";
+
+	status = "okay";
+};
+
+&lpass_tlmm {
+	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	spkr_23_sd_n_active: spkr-23-sd-n-active-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>;
+	pinctrl-names = "default";
+
+	vdd-micb-supply = <&vreg_l1b_1p8>;
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1 2 3>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp2 {
+	status = "okay";
+};
+
+&mdss_dp2_out {
+	data-lanes = <0 1 2 3>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+	/delete-property/ #sound-dai-cells;
+
+	pinctrl-0 = <&edp0_hpd_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+
+			backlight = <&backlight>;
+
+			power-supply = <&vreg_edp_3p3>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dp3_out {
+	data-lanes = <0 1 2 3>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+	remote-endpoint = <&edp_panel_in>;
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3i_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie4_port0 {
+	reset-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
+&pcie6a {
+	vddpe-3v3-supply = <&vreg_nvme>;
+
+	pinctrl-0 = <&pcie6a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l1d_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie6a_port0 {
+	reset-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+};
+
+&pm8550_gpios {
+	edp_bl_pwm: edp-bl-pwm-state {
+		pins = "gpio8";
+		function = "func1";
+	};
+
+	rtmr0_default: rtmr0-reset-n-active-state {
+		pins = "gpio10";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+
+	usb0_3p3_reg_en: usb0-3p3-reg-en-state {
+		pins = "gpio11";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pm8550_pwm {
+	pinctrl-0 = <&edp_bl_pwm>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pm8550ve_8_gpios {
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		input-disable;
+		output-enable;
+		drive-push-pull;
+		power-source = <1>; /* 1.8 V */
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+};
+
+&pm8550ve_9_gpios {
+	usb0_1p8_reg_en: usb0-1p8-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&pmc8380_5_gpios {
+	usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state {
+		pins = "gpio8";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		bias-disable;
+		input-disable;
+		output-enable;
+	};
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
+&qupv3_2 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/ACER/SFA14-11/qcadsp8380.mbn",
+			"qcom/x1e80100/ACER/SFA14-11/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/ACER/SFA14-11/qccdsp8380.mbn",
+			"qcom/x1e80100/ACER/SFA14-11/cdsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&smb2360_0 {
+	status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&swr0 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Left Woofer */
+	left_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Left Tweeter */
+	left_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	/* WCD9385 RX */
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9385 TX */
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 2 3 4>;
+	};
+};
+
+&swr3 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Right Woofer */
+	right_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Right Tweeter */
+	right_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&tcsr {
+	vdda-qrefrpt0-0p9-supply = <&vreg_l3c_0p8>;
+	vdda-qrefrpt1-0p9-supply = <&vreg_l3i_0p8>;
+	vdda-qrefrpt2-0p9-supply = <&vreg_l3i_0p8>;
+	vdda-qrefrpt3-0p9-supply = <&vreg_l3j_0p8>;
+	vdda-qrefrpt4-0p9-supply = <&vreg_l1d_0p8>;
+	vdda-qrefrx0-0p9-supply = <&vreg_l3c_0p8>;
+	vdda-qrefrx1-0p9-supply = <&vreg_l3i_0p8>;
+	vdda-qrefrx2-0p9-supply = <&vreg_l3i_0p8>;
+	vdda-qrefrx3-0p9-supply = <&vreg_l3j_0p8>;
+	vdda-qrefrx4-0p9-supply = <&vreg_l1d_0p8>;
+	vdda-qreftx0-0p9-supply = <&vreg_l3j_0p8>;
+	vdda-qreftx0-1p2-supply = <&vreg_l2j_1p2>;
+	vdda-qreftx1-0p9-supply = <&vreg_l3j_0p8>;
+	vdda-qreftx1-1p2-supply = <&vreg_l3e_1p2>;
+	vdda-refgen0-0p9-supply = <&vreg_l3i_0p8>;
+	vdda-refgen0-1p2-supply = <&vreg_l3e_1p2>;
+	vdda-refgen2-0p9-supply = <&vreg_l3j_0p8>;
+	vdda-refgen2-1p2-supply = <&vreg_l2j_1p2>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <34 2>, /* Unused */
+			       <44 4>, /* SPI (TPM) */
+			       <65 1>, /* EC reset */
+			       <238 1>; /* UFS Reset */
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	eusb6_reset_n: eusb6-reset-n-state {
+		pins = "gpio184";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	hall_int_n_default: hall-int-n-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-disable;
+	};
+
+	hdmi_hpd_default: hdmi-hpd-default-state {
+		pins = "gpio126";
+		function = "usb2_dp";
+		bias-disable;
+	};
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-disable;
+	};
+
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie4_default: pcie4-default-state {
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie6a_default: pcie6a-default-state {
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie6a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	tpad_default: tpad-default-state {
+		pins = "gpio3";
+		function = "gpio";
+		bias-disable;
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio191";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio214";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+		pins = "gpio116", "gpio117";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		max-speed = <3200000>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
+};
+
+&uart21 {
+	compatible = "qcom,geni-debug-uart";
+
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	dr_mode = "host";
+
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_0_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	vdda-phy-supply = <&vreg_l1j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy_dp_in {
+	remote-endpoint = <&mdss_dp0_out>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&retimer_ss0_ss_in>;
+};
+
+&usb_1_ss2_qmpphy {
+	vdda-phy-supply = <&vreg_l2d_0p9>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	/delete-property/ mode-switch;
+	/delete-property/ orientation-switch;
+
+	status = "okay";
+
+	ports {
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/delete-node/ endpoint;
+
+			usb_1_ss2_qmpphy_out_dp: endpoint@0 {
+				reg = <0>;
+
+				data-lanes = <3 2 1 0>;
+				remote-endpoint = <&hdmi_bridge_dp_in>;
+			};
+
+			/* No USB3 lanes connected */
+		};
+	};
+};
+
+&usb_2 {
+	dr_mode = "host";
+
+	status = "okay";
+};
+
+&usb_2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb6_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb3_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb5_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3c_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3c_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
-- 
2.53.0

Re: [PATCH v5 2/2] arm64: dts: qcom: Add support for Acer Swift Go Pro AI (SFA14-11)

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] arm64: dts: qcom: x1e78100-acer-sfa14-11: inverted backlight turns full on at 0
--

commit 66fa11a1de0967d5bc8b8fce1f271477c9fa4b31
Author: Kaipeng Zeng <kaipeng94@gmail.com>

arm64: dts: qcom: Add support for Acer Swift Go Pro AI (SFA14-11)

This commit adds the device tree for the Acer Swift Go Pro AI (SFA14-11)
laptop based on the Qualcomm Snapdragon X Elite (X1E78100) SoC.

> diff --git a/arch/arm64/boot/dts/qcom/x1e78100-acer-sfa14-11.dts b/arch/arm64/boot/dts/qcom/x1e78100-acer-sfa14-11.dts
> new file mode 100644
> index 0000000000000..5814cf3d000ce
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/x1e78100-acer-sfa14-11.dts
> @@ -0,0 +1,1541 @@
[ ... ]
> +	backlight: backlight {
> +		compatible = "pwm-backlight";
> +
> +		pwms = <&pm8550_pwm 3 5000000>;
> +
> +		brightness-levels = <254 225 200 175 150 125 100 75 65 60 55>;
> +		default-brightness-level = <8>;
> +
> +		power-supply = <&vreg_edp_bl>;
> +	};
[ ... ]
> +	vreg_edp_bl: regulator-edp-bl {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "VBL9";
> +		regulator-min-microvolt = <3600000>;
> +		regulator-max-microvolt = <3600000>;
> +
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};

[Severity: Medium]
Does setting the backlight brightness to 0, blanking the display, or
suspending the system cause this active-low backlight to jump to full
brightness instead of turning off?

The backlight node uses descending brightness-levels from 254 (off) down to
55 (maximum brightness) without PWM_POLARITY_INVERTED, has no enable-gpios,
and points power-supply at vreg_edp_bl, which has no GPIO and is marked
regulator-always-on.

In drivers/video/backlight/pwm_bl.c, pwm_backlight_update_status() only
consults pb->levels[brightness] via compute_duty_cycle() when brightness > 0.
When brightness is 0, it ignores pb->levels[0] and instead disables the
regulator and sets duty_cycle = 0:

drivers/video/backlight/pwm_bl.c:pwm_backlight_update_status() {
	if (brightness > 0) {
		pwm_get_state(pb->pwm, &state);
		state.duty_cycle = compute_duty_cycle(pb, brightness, &state);
		state.enabled = true;
		pwm_apply_might_sleep(pb->pwm, &state);

		pwm_backlight_power_on(pb);
	} else {
		pwm_backlight_power_off(pb);

		pwm_get_state(pb->pwm, &state);
		state.duty_cycle = 0;
		state.enabled = !pb->power_supply && !pb->enable_gpio;
		pwm_apply_might_sleep(pb->pwm, &state);
	}
}

Because vreg_edp_bl is a GPIO-less fixed regulator with regulator-always-on,
regulator_disable() in pwm_backlight_power_off() does not cut power to the
backlight, while lpg_pwm_apply() in drivers/leds/rgb/leds-qcom-lpg.c disables
the PWM output channel and drives it to a constant logical 0 (0% duty cycle),
which corresponds to full brightness on an active-low backlight.

In addition, having descending values in brightness-levels causes unsigned
integer wraparound in pwm_backlight_is_linear():

drivers/video/backlight/pwm_bl.c:pwm_backlight_is_linear() {
	unsigned int nlevels = data->max_brightness + 1;
	unsigned int min_val = data->levels[0];
	unsigned int max_val = data->levels[nlevels - 1];
	unsigned int slope = (128 * (max_val - min_val)) / nlevels;
	unsigned int margin = (max_val - min_val) / 20; /* 5% */
	...
}

With min_val = 254 and max_val = 55, max_val - min_val wraps around in
unsigned arithmetic, inflating margin and misreporting the non-linear table
as BACKLIGHT_SCALE_LINEAR.

Note that pm8550_pwm in hamoa-pmics.dtsi uses #pwm-cells = <2>, which does
not accept a third PWM_POLARITY_INVERTED flag cell unless #pwm-cells is
overridden to <3> or the driver/DT handling is adjusted.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261023180513.36417-1-kaipeng94@gmail.com?part=2

Re: [PATCH v5 0/2] Add device tree for Acer Swift Go Pro AI (SFA14-11)

[Jianfeng Liu]

Hi Kaipeng,

Thanks for v5 and for the detailed notes on the eUSB repeaters and the EC — those are very useful.

Two points from my side.

On the naming: I'm fine with the model string carrying the retail name, i.e.

    model = "Acer Swift Go Pro AI (SFA14-11)";

For the compatible, though, I think we should choose a name that can be found on the hardware or in the firmware itself, and "acer,swift-sfa14-11" does that: it matches the DMI product name (SFA14-11) combined with the family name Acer itself uses on its support site ("Swift SFA14-11"). The archived retail page lists the Chinese product name, but it doesn't show the device configuration or images, and in practice users identify their machine by the name Windows shows (which comes from the DMI) or through Acer's support site. So my suggestion is: model = "Acer Swift Go Pro AI (SFA14-11)", compatible = "acer,swift-sfa14-11". Note this is also the string quoted earlier in this thread, while v5 uses "acer,swift-go-sfa14-11" in both the binding and the DTS — could we align on one?

Second, please add the machine to the QSEECOM allowlist (qcom_scm_qseecom_allowlist) as a separate "firmware: qcom: scm" patch. This device's firmware does not accept keyboard input, so the EFI boot order cannot be configured from the setup UI: without QSEECOM/efivars, the only way to boot Linux is to press F12 and select the entry on every boot. With the allowlist entry, efibootmgr can make Linux the default boot entry. This is the same kind of change other boards carry, e.g. the recent addition by Srinivas [1]. My series has it as a third patch; I'm happy to have it folded into whichever series moves forward.

[1] https://lore.kernel.org/all/20260928145122.1337186-1-srinivas.kandagatla@oss.qualcomm.com/

Best regards,
Jianfeng