From: sashiko-bot@kernel.org
To: christian.koever-draxl@student.uibk.ac.at
Cc: devicetree@vger.kernel.org, linux-amlogic@lists.infradead.org,
robh@kernel.org, conor+dt@kernel.org, neil.armstrong@linaro.org
Subject: Re: [PATCH v2 2/2] firmware: meson: sm: make power-off work on S4
Date: Fri, 06 Nov 2026 10:26:26 +0000 [thread overview]
Message-ID: <sashiko-outbox-201214@kernel.org> (raw)
In-Reply-To: <20261106101854.46569-3-christian.koever-draxl@student.uibk.ac.at>
Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [Low] firmware: meson: duplicate meson-sm prefix in
meson_sm_power_off_prepare()
--
commit 0142b0300be6322393138fbe4dbbf32405872dee
Author: Christian Stefan Kövér-Draxl <ckoever@outlook.de>
firmware: meson: sm: make power-off work on S4
This commit registers a power-off prepare handler for Amlogic S4 that
offlines secondary CPUs and sets the firmware shutdown flag before PSCI
SYSTEM_OFF.
> diff --git a/drivers/firmware/meson/meson_sm.c b/drivers/firmware/meson/meson_sm.c
> index ab9751a59b552..de0c8e809c516 100644
> --- a/drivers/firmware/meson/meson_sm.c
> +++ b/drivers/firmware/meson/meson_sm.c
[ ... ]
> @@ -303,6 +306,28 @@ static struct attribute *meson_sm_sysfs_attrs[] = {
> };
> ATTRIBUTE_GROUPS(meson_sm_sysfs);
>
> +/*
> + * The S4 firmware implements PSCI SYSTEM_OFF as DDR self-refresh: on the
> + * power key it jumps back to the kernel instead of booting, which hangs the
> + * board. Setting the shutdown flag first makes it cold-boot instead, and the
> + * secondary CPUs must have been taken down through PSCI CPU_OFF beforehand,
> + * otherwise the wake-up path hangs as well. machine_power_off() only parks
> + * them, so offline them here, while CPU hotplug still works.
> + */
> +static int meson_sm_power_off_prepare(struct sys_off_data *data)
> +{
> + unsigned int cpu, primary = cpumask_first(cpu_online_mask);
> +
> + for_each_online_cpu(cpu) {
> + if (cpu != primary && remove_cpu(cpu))
> + pr_warn("meson-sm: failed to stop CPU%u\n", cpu);
[Severity: Low]
Does this duplicate the "meson-sm: " prefix in the kernel log?
drivers/firmware/meson/meson_sm.c already defines pr_fmt(fmt) as
"meson-sm: " fmt at the top of the file.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261106101854.46569-1-christian.koever-draxl@student.uibk.ac.at?part=2
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
WARNING: multiple messages have this Message-ID (diff)
From: sashiko-bot@kernel.org
To: christian.koever-draxl@student.uibk.ac.at
Cc: devicetree@vger.kernel.org, linux-amlogic@lists.infradead.org,
robh@kernel.org, conor+dt@kernel.org, neil.armstrong@linaro.org
Subject: Re: [PATCH v2 2/2] firmware: meson: sm: make power-off work on S4
Date: Fri, 06 Nov 2026 10:26:26 +0000 [thread overview]
Message-ID: <sashiko-outbox-201214@kernel.org> (raw)
In-Reply-To: <20261106101854.46569-3-christian.koever-draxl@student.uibk.ac.at>
Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [Low] firmware: meson: duplicate meson-sm prefix in
meson_sm_power_off_prepare()
--
commit 0142b0300be6322393138fbe4dbbf32405872dee
Author: Christian Stefan Kövér-Draxl <ckoever@outlook.de>
firmware: meson: sm: make power-off work on S4
This commit registers a power-off prepare handler for Amlogic S4 that
offlines secondary CPUs and sets the firmware shutdown flag before PSCI
SYSTEM_OFF.
> diff --git a/drivers/firmware/meson/meson_sm.c b/drivers/firmware/meson/meson_sm.c
> index ab9751a59b552..de0c8e809c516 100644
> --- a/drivers/firmware/meson/meson_sm.c
> +++ b/drivers/firmware/meson/meson_sm.c
[ ... ]
> @@ -303,6 +306,28 @@ static struct attribute *meson_sm_sysfs_attrs[] = {
> };
> ATTRIBUTE_GROUPS(meson_sm_sysfs);
>
> +/*
> + * The S4 firmware implements PSCI SYSTEM_OFF as DDR self-refresh: on the
> + * power key it jumps back to the kernel instead of booting, which hangs the
> + * board. Setting the shutdown flag first makes it cold-boot instead, and the
> + * secondary CPUs must have been taken down through PSCI CPU_OFF beforehand,
> + * otherwise the wake-up path hangs as well. machine_power_off() only parks
> + * them, so offline them here, while CPU hotplug still works.
> + */
> +static int meson_sm_power_off_prepare(struct sys_off_data *data)
> +{
> + unsigned int cpu, primary = cpumask_first(cpu_online_mask);
> +
> + for_each_online_cpu(cpu) {
> + if (cpu != primary && remove_cpu(cpu))
> + pr_warn("meson-sm: failed to stop CPU%u\n", cpu);
[Severity: Low]
Does this duplicate the "meson-sm: " prefix in the kernel log?
drivers/firmware/meson/meson_sm.c already defines pr_fmt(fmt) as
"meson-sm: " fmt at the top of the file.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261106101854.46569-1-christian.koever-draxl@student.uibk.ac.at?part=2
next prev parent reply other threads:[~2026-11-06 10:26 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-06 10:18 [PATCH v2 0/2] firmware: meson: sm: make power-off work on S4 christian.koever-draxl
2026-11-06 10:18 ` christian.koever-draxl
2026-11-06 10:18 ` [PATCH v2 1/2] dt-bindings: firmware: amlogic,meson-gxbb-sm: add amlogic,meson-s4-sm christian.koever-draxl
2026-11-06 10:18 ` christian.koever-draxl
2026-11-06 13:09 ` Rob Herring
2026-11-06 13:09 ` Rob Herring
2026-11-06 10:18 ` [PATCH v2 2/2] firmware: meson: sm: make power-off work on S4 christian.koever-draxl
2026-11-06 10:18 ` christian.koever-draxl
2026-11-06 10:26 ` sashiko-bot [this message]
2026-11-06 10:26 ` sashiko-bot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=sashiko-outbox-201214@kernel.org \
--to=sashiko-bot@kernel.org \
--cc=christian.koever-draxl@student.uibk.ac.at \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-amlogic@lists.infradead.org \
--cc=neil.armstrong@linaro.org \
--cc=robh@kernel.org \
--cc=sashiko-reviews@lists.linux.dev \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.