* [PATCH v3 0/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board support
@ 2026-11-19 7:10 Gopikishan Thawre
2026-11-19 7:10 ` [PATCH v3 1/3] dt-bindings: arm: qcom: Add LeMans Draco EVK board Gopikishan Thawre
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Gopikishan Thawre @ 2026-11-19 7:10 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Abel Vesa, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Richard Cochran
Cc: Gopikishan Thawre, linux-arm-msm, devicetree, linux-kernel,
netdev, Krzysztof Kozlowski, Kishor Buchi, Vishnu Saini,
Khalid Faisal Ansari, Ajinkya Inchure, Anuj Tripathi,
Sushrut Shree Trivedi, Wei Deng
Add device tree support for the LeMans Draco EVK, an evaluation kit
based on the SA8775P/QCS9100 SoC targeting automotive and industrial
use cases. The platform consists of a System on Module (SoM) paired
with the Draco carrier board.
The LeMans Draco SoM integrates the SA8775P/QCS9100 SoC, three
PMM8654AU PMICs, UFS storage, USB 0/1/2, GPU (Adreno 663), and
essential connectivity. A dedicated SoM .dtsi allows carrier board
device trees to reuse common SoM peripherals without duplication.
The Draco carrier board provides board-specific peripherals:
- Four DisplayPort outputs (DP0-DP3) via MDSS0 and MDSS1
- I2C GPIO expanders (TCA6416 x4, PCA9534 x2) and EEPROM-based MAC
address storage on i2c18
- Dual Ethernet (ethernet0/ethernet1) with HSGMII PHY over SerDes
- ST33HTPM TPM over SPI16
- AMC6821 fan controller on i2c4
- PCIe0 to NTN3 switch and PCIe1 to x4 slot or M.2 M-key (dip switch)
- M.2 E-key slot with 3.3V supply and PCIe/UART for Wi-Fi/BT module
Link: https://lore.kernel.org/r/20261019-lemans-draco-final-changes-bringup-v1-0-dcabe94f1074@oss.qualcomm.com
Signed-off-by: Gopikishan Thawre <gopikishan.thawre@oss.qualcomm.com>
---
Changes in v3:
- Add PCIe0 (connects to NTN3 switch) and PCIe1 (routable to x4 slot
or M.2 M-key depending on dip switch) with pinctrl states and IOMMU
mappings. [Sushrut Shree Trivedi]
- Add M.2 E-key connectivity slot with always-on 3.3V supply and
PCIe/UART graph connections for Wi-Fi/BT via pwrseq-pcie-m2.
[Wei Deng]
- Move MDSS DP PHY supply assignments to lemans-draco-som.dtsi.
Changes in v2:
- Sort DT node order: move tlmm block after i2c18 node. [Dmitry Baryshkov]
- Drop unused sub-node labels ethernet0_mdc, ethernet0_mdio,
ethernet1_mdc and ethernet1_mdio. [Konrad Dybcio]
- Improve dt-bindings commit message to explain the two-compatible
SoM/carrier hierarchy. [Krzysztof Kozlowski]
To: Bjorn Andersson <andersson@kernel.org>
To: Konrad Dybcio <konradybcio@kernel.org>
To: Abel Vesa <abelvesa@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Richard Cochran <richardcochran@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
---
Gopikishan Thawre (3):
dt-bindings: arm: qcom: Add LeMans Draco EVK board
arm64: dts: qcom: lemans: Add LeMans Draco EVK SoM platform
arm64: dts: qcom: lemans: Add LeMans Draco EVK board
Documentation/devicetree/bindings/arm/qcom.yaml | 7 +
arch/arm64/boot/dts/qcom/Makefile | 5 +
arch/arm64/boot/dts/qcom/lemans-draco-evk.dts | 778 ++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/lemans-draco-som.dtsi | 421 +++++++++++++
4 files changed, 1211 insertions(+)
---
base-commit: 84abb955b1015477aa11a96e2f3ac1b938b77f48
change-id: 20261013-lemans-draco-final-changes-bringup-1b7b76f8b2e3
Best regards,
--
Gopikishan Thawre <gopikishan.thawre@oss.qualcomm.com>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 1/3] dt-bindings: arm: qcom: Add LeMans Draco EVK board
2026-11-19 7:10 [PATCH v3 0/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board support Gopikishan Thawre
@ 2026-11-19 7:10 ` Gopikishan Thawre
2026-11-19 7:10 ` [PATCH v3 2/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK SoM platform Gopikishan Thawre
2026-11-19 7:10 ` [PATCH v3 3/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board Gopikishan Thawre
2 siblings, 0 replies; 6+ messages in thread
From: Gopikishan Thawre @ 2026-11-19 7:10 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Abel Vesa, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Richard Cochran
Cc: Gopikishan Thawre, linux-arm-msm, devicetree, linux-kernel,
netdev, Krzysztof Kozlowski
Add compatible strings for the LeMans Draco EVK, an evaluation board
based on the SA8775P/QCS9100 SoC family.
The platform uses a two-board design: the LeMans Draco SoM carrying
the SA8775P/QCS9100 SoC and core connectivity, paired with the Draco
carrier board providing application-specific peripherals.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Gopikishan Thawre <gopikishan.thawre@oss.qualcomm.com>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 7ffa4f69987f..3d63e797cf60 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -545,6 +545,13 @@ properties:
- const: qcom,qcs9100
- const: qcom,sa8775p
+ - items:
+ - enum:
+ - qcom,lemans-draco-evk
+ - const: qcom,lemans-draco-som
+ - const: qcom,qcs9100
+ - const: qcom,sa8775p
+
- description: Qualcomm AR2 Gen1 platform
items:
- enum:
--
2.43.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 2/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK SoM platform
2026-11-19 7:10 [PATCH v3 0/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board support Gopikishan Thawre
2026-11-19 7:10 ` [PATCH v3 1/3] dt-bindings: arm: qcom: Add LeMans Draco EVK board Gopikishan Thawre
@ 2026-11-19 7:10 ` Gopikishan Thawre
2026-11-20 7:11 ` sashiko-bot
2026-11-19 7:10 ` [PATCH v3 3/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board Gopikishan Thawre
2 siblings, 1 reply; 6+ messages in thread
From: Gopikishan Thawre @ 2026-11-19 7:10 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Abel Vesa, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Richard Cochran
Cc: Gopikishan Thawre, linux-arm-msm, devicetree, linux-kernel,
netdev, Kishor Buchi
Introduce the device tree for the SA8775P/QCS9100-based LeMans Draco
EVK SoM. The LeMans Draco SoM is a compact compute module integrating
the SA8775P SoC, three PMM8654AU PMICs, and essential connectivity,
designed to mount on carrier boards.
The initial SoM device tree includes basic support for:
- RPMH regulators for three PMM8654AU PMICs
- QUP firmware paths (qupv3_id_0/1/2)
- Remoteproc instances (ADSP, CDSP0/1, GPDSP0/1) with firmware paths
- Debug UART (uart10) and board clocks
- UFS storage
- USB 0, USB 1 (host mode) and USB 2 with HSPHY and QMP PHY supplies
- GPU (Adreno 663) with ZAP shader firmware
- Video processing unit (iris)
The SoM device tree includes lemans-embedded.dtsi rather than lemans.dtsi
directly, as platform resources (clocks, regulators, interconnects, PHYs
and pinctrls) were moved from lemans.dtsi into lemans-embedded.dtsi to
allow lemans.dtsi to serve the GearVM variant [1].
[1] https://lore.kernel.org/all/20261031131042.1200862-4-shengchao.guo@oss.qualcomm.com/
Co-developed-by: Kishor Buchi <kbuchi@qti.qualcomm.com>
Signed-off-by: Kishor Buchi <kbuchi@qti.qualcomm.com>
Signed-off-by: Gopikishan Thawre <gopikishan.thawre@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/lemans-draco-som.dtsi | 421 +++++++++++++++++++++++++
1 file changed, 421 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/lemans-draco-som.dtsi b/arch/arm64/boot/dts/qcom/lemans-draco-som.dtsi
new file mode 100644
index 000000000000..1001b6b81c31
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/lemans-draco-som.dtsi
@@ -0,0 +1,421 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "lemans-embedded.dtsi"
+#include "lemans-pmics.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart10;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_s4a: smps4 {
+ regulator-name = "vreg_s4a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1816000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5a: smps5 {
+ regulator-name = "vreg_s5a";
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <1996000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s9a: smps9 {
+ regulator-name = "vreg_s9a";
+ regulator-min-microvolt = <535000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4a: ldo4 {
+ regulator-name = "vreg_l4a";
+ regulator-min-microvolt = <788000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <870000>;
+ regulator-max-microvolt = <950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6a: ldo6 {
+ regulator-name = "vreg_l6a";
+ regulator-min-microvolt = <870000>;
+ regulator-max-microvolt = <970000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <720000>;
+ regulator-max-microvolt = <950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8a: ldo8 {
+ regulator-name = "vreg_l8a";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9a: ldo9 {
+ regulator-name = "vreg_l9a";
+ regulator-min-microvolt = <2970000>;
+ regulator-max-microvolt = <3544000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <1140000>;
+ regulator-max-microvolt = <1260000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c: ldo2 {
+ regulator-name = "vreg_l2c";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3c: ldo3 {
+ regulator-name = "vreg_l3c";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c: ldo4 {
+ regulator-name = "vreg_l4c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5c: ldo5 {
+ regulator-name = "vreg_l5c";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c: ldo6 {
+ regulator-name = "vreg_l6c";
+ regulator-min-microvolt = <1620000>;
+ regulator-max-microvolt = <1980000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <1620000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c: ldo8 {
+ regulator-name = "vreg_l8c";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c: ldo9 {
+ regulator-name = "vreg_l9c";
+ regulator-min-microvolt = <1650000>;
+ regulator-max-microvolt = <2700000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vreg_s4e: smps4 {
+ regulator-name = "vreg_s4e";
+ regulator-min-microvolt = <970000>;
+ regulator-max-microvolt = <1520000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s7e: smps7 {
+ regulator-name = "vreg_s7e";
+ regulator-min-microvolt = <1010000>;
+ regulator-max-microvolt = <1170000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s9e: smps9 {
+ regulator-name = "vreg_s9e";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <570000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6e: ldo6 {
+ regulator-name = "vreg_l6e";
+ regulator-min-microvolt = <1280000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8e: ldo8 {
+ regulator-name = "vreg_l8e";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&gpu {
+ status = "okay";
+};
+
+&gpu_zap_shader {
+ firmware-name = "qcom/sa8775p/a663_zap.mbn";
+};
+
+&iris {
+ firmware-name = "qcom/vpu/vpu30_p4_s6_16mb.mbn";
+
+ status = "okay";
+};
+
+&mdss0_dp0_phy {
+ vdda-phy-supply = <&vreg_l1c>;
+ vdda-pll-supply = <&vreg_l4a>;
+};
+
+&mdss0_dp1_phy {
+ vdda-phy-supply = <&vreg_l1c>;
+ vdda-pll-supply = <&vreg_l4a>;
+};
+
+&mdss1_dp0_phy {
+ vdda-phy-supply = <&vreg_l1c>;
+ vdda-pll-supply = <&vreg_l4a>;
+};
+
+&mdss1_dp1_phy {
+ vdda-phy-supply = <&vreg_l1c>;
+ vdda-pll-supply = <&vreg_l4a>;
+};
+
+&pmm8654au_0_pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+
+ status = "okay";
+};
+
+&qupv3_id_0 {
+ firmware-name = "qcom/sa8775p/qupv3fw.elf";
+
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ firmware-name = "qcom/sa8775p/qupv3fw.elf";
+
+ status = "okay";
+};
+
+&qupv3_id_2 {
+ firmware-name = "qcom/sa8775p/qupv3fw.elf";
+
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sa8775p/adsp.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp0 {
+ firmware-name = "qcom/sa8775p/cdsp0.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp1 {
+ firmware-name = "qcom/sa8775p/cdsp1.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_gpdsp0 {
+ firmware-name = "qcom/sa8775p/gpdsp0.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_gpdsp1 {
+ firmware-name = "qcom/sa8775p/gpdsp1.mbn";
+
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32768>;
+};
+
+&uart10 {
+ compatible = "qcom,geni-debug-uart";
+ pinctrl-0 = <&qup_uart10_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l8a>;
+ vcc-max-microamp = <1100000>;
+ vccq-supply = <&vreg_l4c>;
+ vccq-max-microamp = <1200000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l4a>;
+ vdda-pll-supply = <&vreg_l1c>;
+
+ status = "okay";
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_0_hsphy {
+ vdda-pll-supply = <&vreg_l7a>;
+ vdda18-supply = <&vreg_l6c>;
+ vdda33-supply = <&vreg_l9a>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy {
+ vdda-phy-supply = <&vreg_l1c>;
+ vdda-pll-supply = <&vreg_l7a>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ dr_mode = "host";
+
+ status = "okay";
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l7a>;
+ vdda18-supply = <&vreg_l6c>;
+ vdda33-supply = <&vreg_l9a>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ vdda-phy-supply = <&vreg_l1c>;
+ vdda-pll-supply = <&vreg_l7a>;
+
+ status = "okay";
+};
+
+&usb_2 {
+ status = "okay";
+};
+
+&usb_2_hsphy {
+ vdda-pll-supply = <&vreg_l7a>;
+ vdda18-supply = <&vreg_l6c>;
+ vdda33-supply = <&vreg_l9a>;
+
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 3/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board
2026-11-19 7:10 [PATCH v3 0/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board support Gopikishan Thawre
2026-11-19 7:10 ` [PATCH v3 1/3] dt-bindings: arm: qcom: Add LeMans Draco EVK board Gopikishan Thawre
2026-11-19 7:10 ` [PATCH v3 2/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK SoM platform Gopikishan Thawre
@ 2026-11-19 7:10 ` Gopikishan Thawre
2026-11-20 7:11 ` sashiko-bot
2 siblings, 1 reply; 6+ messages in thread
From: Gopikishan Thawre @ 2026-11-19 7:10 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Abel Vesa, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Richard Cochran
Cc: Gopikishan Thawre, linux-arm-msm, devicetree, linux-kernel,
netdev, Vishnu Saini, Khalid Faisal Ansari, Ajinkya Inchure,
Anuj Tripathi, Sushrut Shree Trivedi, Wei Deng
Add the device tree for the LeMans Draco EVK platform which combines
the LeMans Draco EVK SoM and Draco carrier board.
This device tree adds board-specific peripheral configuration on top
of the SoM, including:
- I2C GPIO expanders (TCA6416/PCA9534) on i2c2 and i2c18
- EEPROM with MAC address nvmem layout on i2c18
- Native DisplayPort output (DP0-DP3)
- Dual Ethernet (ethernet0/ethernet1) with HSGMII PHY over SerDes
- ST33HTPM TPM over SPI16
- AMC6821 fan controller on i2c4
- PCIe0 (connects to NTN3 switch) and PCIe1 (routable to x4 slot
or M.2 M-key depending on dip switch configuration)
- M.2 E-key connectivity slot with always-on 3.3V supply, PCIe and
UART graph connections for Wi-Fi/BT via pwrseq-pcie-m2
Co-developed-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
Signed-off-by: Vishnu Saini <vishnu.saini@oss.qualcomm.com>
Co-developed-by: Khalid Faisal Ansari <khalid.ansari@oss.qualcomm.com>
Signed-off-by: Khalid Faisal Ansari <khalid.ansari@oss.qualcomm.com>
Co-developed-by: Ajinkya Inchure <ainchure@qti.qualcomm.com>
Signed-off-by: Ajinkya Inchure <ainchure@qti.qualcomm.com>
Co-developed-by: Anuj Tripathi <anuj.tripathi@oss.qualcomm.com>
Signed-off-by: Anuj Tripathi <anuj.tripathi@oss.qualcomm.com>
Co-developed-by: Sushrut Shree Trivedi <sushrut.trivedi@oss.qualcomm.com>
Signed-off-by: Sushrut Shree Trivedi <sushrut.trivedi@oss.qualcomm.com>
Co-developed-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Wei Deng <wei.deng@oss.qualcomm.com>
Signed-off-by: Gopikishan Thawre <gopikishan.thawre@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/Makefile | 5 +
arch/arm64/boot/dts/qcom/lemans-draco-evk.dts | 778 ++++++++++++++++++++++++++
2 files changed, 783 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 9553e3aaeccb..11448d8c7087 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -62,6 +62,11 @@ dtb-$(CONFIG_ARCH_QCOM) += kaanapali-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += kaanapali-qrd.dtb
dtb-$(CONFIG_ARCH_QCOM) += kalambo-crd.dtb
dtb-$(CONFIG_ARCH_QCOM) += lemans-evk.dtb
+dtb-$(CONFIG_ARCH_QCOM) += lemans-draco-evk.dtb
+
+lemans-draco-evk-el2-dtbs := lemans-draco-evk.dtb lemans-el2.dtbo
+
+dtb-$(CONFIG_ARCH_QCOM) += lemans-draco-evk-el2.dtb
lemans-evk-camera-csi1-imx577-dtbs := lemans-evk.dtb lemans-evk-camera-csi1-imx577.dtbo
lemans-evk-camera-dtbs := lemans-evk.dtb lemans-evk-camera.dtbo
diff --git a/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts b/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts
new file mode 100644
index 000000000000..7ac3a867d29a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts
@@ -0,0 +1,778 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include <dt-bindings/pwm/pwm.h>
+#include "lemans-draco-som.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. Lemans Draco EVK";
+ compatible = "qcom,lemans-draco-evk", "qcom,lemans-draco-som",
+ "qcom,qcs9100", "qcom,sa8775p";
+ chassis-type = "embedded";
+
+ aliases {
+ ethernet0 = ðernet0;
+ ethernet1 = ðernet1;
+ serial1 = &uart17;
+ };
+
+ dp0-connector {
+ compatible = "dp-connector";
+ label = "DP0";
+ type = "full-size";
+
+ dp-pwr-supply = <&vreg_dp0_pwr>;
+
+ port {
+ dp0_connector_in: endpoint {
+ remote-endpoint = <&mdss0_dp0_out>;
+ };
+ };
+ };
+
+ dp1-connector {
+ compatible = "dp-connector";
+ label = "DP1";
+ type = "full-size";
+
+ dp-pwr-supply = <&vreg_dp1_pwr>;
+
+ port {
+ dp1_connector_in: endpoint {
+ remote-endpoint = <&mdss0_dp1_out>;
+ };
+ };
+ };
+
+ dp2-connector {
+ compatible = "dp-connector";
+ label = "DP2";
+ type = "full-size";
+
+ dp-pwr-supply = <&vreg_dp2_pwr>;
+
+ port {
+ dp2_connector_in: endpoint {
+ remote-endpoint = <&mdss1_dp0_out>;
+ };
+ };
+ };
+
+ dp3-connector {
+ compatible = "dp-connector";
+ label = "DP3";
+ type = "full-size";
+
+ dp-pwr-supply = <&vreg_dp3_pwr>;
+
+ port {
+ dp3_connector_in: endpoint {
+ remote-endpoint = <&mdss1_dp1_out>;
+ };
+ };
+ };
+
+ vreg_0p9: regulator-0v9 {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_0P9";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vreg_1p8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_1P8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vreg_dp0_pwr: regulator-dp0-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_DP0_PWR_3P3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&expander1 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ vreg_dp1_pwr: regulator-dp1-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_DP1_PWR_3P3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&expander1 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ vreg_dp2_pwr: regulator-dp2-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_DP2_PWR_3P3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&expander1 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ vreg_dp3_pwr: regulator-dp3-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "VREG_DP3_PWR_3P3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&expander1 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ vreg_keye_3p3: regulator-keye-3p3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_keye_3p3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ wifi-bt-connector {
+ compatible = "pcie-m2-e-connector";
+ vpcie3v3-supply = <&vreg_keye_3p3>;
+ w-disable2-gpios = <&pmm8654au_1_gpios 8 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ m2_e_pcie_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tc9563_pcie1_ep>;
+ };
+ };
+
+ port@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ m2_e_uart_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&uart17_ep>;
+ };
+ };
+ };
+ };
+};
+
+ðernet0 {
+ phy-handle = <&hsgmii_phy0>;
+ phy-mode = "2500base-x";
+
+ pinctrl-0 = <ðernet0_default>;
+ pinctrl-names = "default";
+
+ snps,mtl-rx-config = <&mtl_rx_setup>;
+ snps,mtl-tx-config = <&mtl_tx_setup>;
+
+ nvmem-cells = <&mac_addr0>;
+ nvmem-cell-names = "mac-address";
+
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hsgmii_phy0: ethernet-phy@1c {
+ compatible = "ethernet-phy-id004d.d101";
+ reg = <0x1c>;
+ reset-gpios = <&pmm8654au_2_gpios 8 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <11000>;
+ reset-deassert-us = <70000>;
+ };
+ };
+
+ mtl_rx_setup: rx-queues-config {
+ snps,rx-queues-to-use = <4>;
+ snps,rx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,route-up;
+ snps,priority = <0x1>;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x1>;
+ snps,route-ptp;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x2>;
+ snps,route-avcp;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x3>;
+ snps,priority = <0xc>;
+ };
+ };
+
+ mtl_tx_setup: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+
+ queue0 {
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+ };
+};
+
+ðernet1 {
+ phy-handle = <&hsgmii_phy1>;
+ phy-mode = "2500base-x";
+
+ pinctrl-0 = <ðernet1_default>;
+ pinctrl-names = "default";
+
+ snps,mtl-rx-config = <&mtl_rx_setup1>;
+ snps,mtl-tx-config = <&mtl_tx_setup1>;
+
+ nvmem-cells = <&mac_addr1>;
+ nvmem-cell-names = "mac-address";
+
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hsgmii_phy1: ethernet-phy@1c {
+ compatible = "ethernet-phy-id004d.d101";
+ reg = <0x1c>;
+ reset-gpios = <&pmm8654au_2_gpios 9 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <11000>;
+ reset-deassert-us = <70000>;
+ };
+ };
+
+ mtl_rx_setup1: rx-queues-config {
+ snps,rx-queues-to-use = <4>;
+ snps,rx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,route-up;
+ snps,priority = <0x1>;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x1>;
+ snps,route-ptp;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x2>;
+ snps,route-avcp;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x3>;
+ snps,priority = <0xc>;
+ };
+ };
+
+ mtl_tx_setup1: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+
+ queue0 {
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+ };
+};
+
+&i2c18 {
+ status = "okay";
+
+ expander5: gpio@3c {
+ compatible = "nxp,pca9534";
+ reg = <0x3c>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ eeprom@50 {
+ compatible = "giantec,gt24c256c", "atmel,24c256";
+ reg = <0x50>;
+ pagesize = <64>;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mac_addr0: mac-addr@0 {
+ reg = <0x0 0x6>;
+ };
+
+ mac_addr1: mac-addr@6 {
+ reg = <0x6 0x6>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ status = "okay";
+
+ expander0: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ expander1: gpio@21 {
+ compatible = "ti,tca6416";
+ reg = <0x21>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ expander2: gpio@22 {
+ compatible = "ti,tca6416";
+ reg = <0x22>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ expander3: gpio@23 {
+ compatible = "ti,tca6416";
+ reg = <0x23>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ expander4: gpio@38 {
+ compatible = "nxp,pca9534";
+ reg = <0x38>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+};
+
+&i2c4 {
+ status = "okay";
+
+ fan_controller: fan@1a {
+ compatible = "ti,amc6821";
+ reg = <0x1a>;
+ #pwm-cells = <2>;
+
+ fan {
+ pwms = <&fan_controller 40000 PWM_POLARITY_INVERTED>;
+ };
+ };
+};
+
+&mdss0 {
+ status = "okay";
+};
+
+&mdss0_dp0 {
+ pinctrl-0 = <&dp0_hot_plug_det>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&mdss0_dp0_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&dp0_connector_in>;
+};
+
+&mdss0_dp0_phy {
+ status = "okay";
+};
+
+&mdss0_dp1 {
+ pinctrl-0 = <&dp1_hot_plug_det>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&mdss0_dp1_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&dp1_connector_in>;
+};
+
+&mdss0_dp1_phy {
+ status = "okay";
+};
+
+&mdss1 {
+ status = "okay";
+};
+
+&mdss1_dp0 {
+ pinctrl-0 = <&dp2_hot_plug_det>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&mdss1_dp0_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&dp2_connector_in>;
+};
+
+&mdss1_dp0_phy {
+ status = "okay";
+};
+
+&mdss1_dp1 {
+ pinctrl-0 = <&dp3_hot_plug_det>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&mdss1_dp1_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&dp3_connector_in>;
+};
+
+&mdss1_dp1_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ iommu-map = <0x0 &pcie_smmu 0x0 0x0 0x1>,
+ <0x100 &pcie_smmu 0x1 0x0 0x1>,
+ <0x208 &pcie_smmu 0x2 0x0 0x1>,
+ <0x210 &pcie_smmu 0x3 0x0 0x1>,
+ <0x218 &pcie_smmu 0x4 0x0 0x1>,
+ <0x300 &pcie_smmu 0x5 0x0 0x1>,
+ <0x400 &pcie_smmu 0x6 0x0 0x1>,
+ <0x500 &pcie_smmu 0x7 0x0 0x1>,
+ <0x501 &pcie_smmu 0x8 0x0 0x1>;
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l1c>;
+ vdda-qref-supply = <&vreg_l4a>;
+ vdda-refgen-supply = <&vreg_l7a>;
+
+ status = "okay";
+};
+
+&pcie1 {
+ perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&pcie1_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l5a>;
+ vdda-pll-supply = <&vreg_l1c>;
+ vdda-qref-supply = <&vreg_l4a>;
+ vdda-refgen-supply = <&vreg_l7a>;
+
+ status = "okay";
+};
+
+&pcieport0 {
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ pcie@0,0 {
+ compatible = "pci1179,0623";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x2 0xff>;
+
+ vddc-supply = <&vreg_0p9>;
+ vdd18-supply = <&vreg_1p8>;
+ vdd09-supply = <&vreg_0p9>;
+ vddio1-supply = <&vreg_1p8>;
+ vddio2-supply = <&vreg_1p8>;
+ vddio18-supply = <&vreg_1p8>;
+ i2c-parent = <&i2c18 0x77>;
+ resx-gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&tc9563_resx_n>;
+ pinctrl-names = "default";
+
+ pcie@1,0 {
+ reg = <0x20800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x3 0xff>;
+
+ port {
+ tc9563_pcie1_ep: endpoint {};
+ };
+ };
+
+ pcie@2,0 {
+ reg = <0x21000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x4 0xff>;
+ };
+
+ pcie@3,0 {
+ reg = <0x21800 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ bus-range = <0x5 0xff>;
+
+ pcie@0,0 {
+ reg = <0x50000 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ };
+
+ pcie@0,1 {
+ reg = <0x50100 0x0 0x0 0x0 0x0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges;
+ };
+ };
+ };
+};
+
+&qup_i2c4_default {
+ drive-strength = <6>;
+ bias-pull-up;
+};
+
+&serdes0 {
+ phy-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&serdes1 {
+ phy-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&spi16 {
+ status = "okay";
+
+ tpm@0 {
+ compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&tc9563_pcie1_ep {
+ remote-endpoint = <&m2_e_pcie_ep>;
+};
+
+&tlmm {
+
+ dp2_hot_plug_det: dp2-hot-plug-det-state {
+ pins = "gpio104";
+ function = "edp2_hot";
+ bias-disable;
+ };
+
+ dp3_hot_plug_det: dp3-hot-plug-det-state {
+ pins = "gpio103";
+ function = "edp3_hot";
+ bias-disable;
+ };
+
+ ethernet0_default: ethernet0-default-state {
+ ethernet0-mdc-pins {
+ pins = "gpio8";
+ function = "emac0_mdc";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ ethernet0-mdio-pins {
+ pins = "gpio9";
+ function = "emac0_mdio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
+ ethernet1_default: ethernet1-default-state {
+ ethernet1-mdc-pins {
+ pins = "gpio20";
+ function = "emac1_mdc";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ ethernet1-mdio-pins {
+ pins = "gpio21";
+ function = "emac1_mdio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
+ pcie0_default_state: pcie0-default-state {
+ clkreq-pins {
+ pins = "gpio1";
+ function = "pcie0_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-pins {
+ pins = "gpio2";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake-pins {
+ pins = "gpio0";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie1_default_state: pcie1-default-state {
+ clkreq-pins {
+ pins = "gpio3";
+ function = "pcie1_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-pins {
+ pins = "gpio4";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake-pins {
+ pins = "gpio5";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ tc9563_resx_n: tc9563-resx-state {
+ pins = "gpio10";
+ function = "gpio";
+ bias-disable;
+ output-high;
+ };
+};
+
+&uart17 {
+ status = "okay";
+
+ port {
+ uart17_ep: endpoint {
+ remote-endpoint = <&m2_e_uart_ep>;
+ };
+ };
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v3 2/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK SoM platform
2026-11-19 7:10 ` [PATCH v3 2/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK SoM platform Gopikishan Thawre
@ 2026-11-20 7:11 ` sashiko-bot
0 siblings, 0 replies; 6+ messages in thread
From: sashiko-bot @ 2026-11-20 7:11 UTC (permalink / raw)
To: Gopikishan Thawre; +Cc: devicetree, robh, conor+dt
Thank you for your contribution! Sashiko AI review found 1 potential
issue to consider:
- [Medium] arm64: dts: qcom: lemans-draco-som: swapped USB QMP PHY vdda
supplies
--
commit 53f3c4c5688995a724474882d7b554c0d74f4ff6
Author: Gopikishan Thawre <gopikishan.thawre@oss.qualcomm.com>
arm64: dts: qcom: lemans: Add LeMans Draco EVK SoM platform
This commit adds the initial device tree for the SA8775P/QCS9100-based
LeMans Draco EVK SoM platform.
> diff --git a/arch/arm64/boot/dts/qcom/lemans-draco-som.dtsi b/arch/arm64/boot/dts/qcom/lemans-draco-som.dtsi
> new file mode 100644
> index 0000000000000..1001b6b81c312
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/lemans-draco-som.dtsi
> @@ -0,0 +1,421 @@
[ ... ]
> +&usb_0_qmpphy {
> + vdda-phy-supply = <&vreg_l1c>;
> + vdda-pll-supply = <&vreg_l7a>;
> +
> + status = "okay";
> +};
> +
> +&usb_1 {
> + dr_mode = "host";
> +
> + status = "okay";
> +};
> +
> +&usb_1_hsphy {
> + vdda-pll-supply = <&vreg_l7a>;
> + vdda18-supply = <&vreg_l6c>;
> + vdda33-supply = <&vreg_l9a>;
> +
> + status = "okay";
> +};
> +
> +&usb_1_qmpphy {
> + vdda-phy-supply = <&vreg_l1c>;
> + vdda-pll-supply = <&vreg_l7a>;
> +
> + status = "okay";
> +};
[Severity: Medium]
Are vdda-phy-supply and vdda-pll-supply swapped on usb_0_qmpphy and
usb_1_qmpphy?
vreg_l1c is the ~1.2V rail and vreg_l7a is the ~0.88V rail, whereas the
QMP PHY expects the lower voltage on vdda-phy-supply and the 1.2V rail
on vdda-pll-supply (matching ufs_mem_phy above and commit 932113c3c778
("arm64: dts: qcom: lemans: Fix swapped USB QMP PHY vdda-phy/vdda-pll
supplies")). Because both regulators set regulator-allow-set-load, the
QMP USB PHY driver also programs its vdda-phy and vdda-pll load votes
onto the wrong LDOs.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261119-lemans-draco-final-changes-bringup-v3-0-db08f12f0cd5@oss.qualcomm.com?part=2
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v3 3/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board
2026-11-19 7:10 ` [PATCH v3 3/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board Gopikishan Thawre
@ 2026-11-20 7:11 ` sashiko-bot
0 siblings, 0 replies; 6+ messages in thread
From: sashiko-bot @ 2026-11-20 7:11 UTC (permalink / raw)
To: Gopikishan Thawre; +Cc: devicetree, robh, conor+dt
Thank you for your contribution! Sashiko AI review found 8 potential
issues to consider:
- [High] arm64: dts: qcom: wrong deprecated phy-supply on serdes0 and
serdes1
- [High] arm64: dts: qcom: missing enable-active-high on DP power
regulators
- [High] arm64: dts: qcom: misplaced PCIe PERST#/WAKE# GPIOs and wrong
WAKE# polarity
- [High] arm64: dts: qcom: missing pciclass,0604 compatible on TC9563
pcie@1,0 port
- [High] arm64: dts: qcom: swapped vdda-phy and vdda-pll on USB QMP PHYs
in Draco SoM
- [Medium] arm64: dts: qcom: TC9563 endpoint functions under pcie@3,0
modeled as bridges
- [Low] arm64: dts: qcom: undocumented vdda-refgen-supply on pcie0_phy
and pcie1_phy
- [Low] arm64: dts: qcom: Makefile entries for lemans-draco-evk out of
order
--
commit cde350979c0cc65bfe5158a7e63d40d7f1a15e33
Author: Gopikishan Thawre <gopikishan.thawre@oss.qualcomm.com>
arm64: dts: qcom: lemans: Add LeMans Draco EVK board
This commit adds the device tree and Makefile entries for the Qualcomm
LeMans Draco EVK board, building on top of the LeMans Draco SoM DTSI.
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 9553e3aaeccb0..11448d8c70876 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -62,6 +62,11 @@ dtb-$(CONFIG_ARCH_QCOM) += kaanapali-mtp.dtb
> dtb-$(CONFIG_ARCH_QCOM) += kaanapali-qrd.dtb
> dtb-$(CONFIG_ARCH_QCOM) += kalambo-crd.dtb
> dtb-$(CONFIG_ARCH_QCOM) += lemans-evk.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += lemans-draco-evk.dtb
> +
> +lemans-draco-evk-el2-dtbs := lemans-draco-evk.dtb lemans-el2.dtbo
> +
> +dtb-$(CONFIG_ARCH_QCOM) += lemans-draco-evk-el2.dtb
[Severity: Low]
This isn't a bug, but lemans-draco-evk.dtb and lemans-draco-evk-el2.dtb
sort alphabetically before lemans-evk.dtb.
> diff --git a/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts b/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts
> new file mode 100644
> index 0000000000000..7ac3a867d29a6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/lemans-draco-evk.dts
> @@ -0,0 +1,778 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
> + */
> +/dts-v1/;
> +
> +#include <dt-bindings/pwm/pwm.h>
> +#include "lemans-draco-som.dtsi"
[Severity: High]
Are vdda-phy-supply and vdda-pll-supply swapped on usb_0_qmpphy and
usb_1_qmpphy in lemans-draco-som.dtsi (added in commit "arm64: dts: qcom:
lemans: Add LeMans Draco EVK SoM platform")?
Both USB QMP PHY nodes assign the 1.2V rail (vreg_l1c) to vdda-phy-supply
and the ~0.88V rail (vreg_l7a) to vdda-pll-supply:
arch/arm64/boot/dts/qcom/lemans-draco-som.dtsi:
&usb_0_qmpphy {
vdda-phy-supply = <&vreg_l1c>;
vdda-pll-supply = <&vreg_l7a>;
status = "okay";
};
As fixed for other LeMans boards in 932113c3c778 ("arm64: dts: qcom:
lemans: Fix swapped USB QMP PHY vdda-phy/vdda-pll supplies") and matching
ufs_mem_phy in the same SoM file, the SA8775P QMP PHY expects the ~0.88V
rail (vreg_l7a) on vdda-phy-supply and the 1.2V rail (vreg_l1c) on
vdda-pll-supply.
[ ... ]
> + vreg_dp0_pwr: regulator-dp0-pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "VREG_DP0_PWR_3P3";
> +
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&expander1 7 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vreg_dp1_pwr: regulator-dp1-pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "VREG_DP1_PWR_3P3";
> +
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&expander1 8 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vreg_dp2_pwr: regulator-dp2-pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "VREG_DP2_PWR_3P3";
> +
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&expander1 9 GPIO_ACTIVE_HIGH>;
> + };
> +
> + vreg_dp3_pwr: regulator-dp3-pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "VREG_DP3_PWR_3P3";
> +
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&expander1 10 GPIO_ACTIVE_HIGH>;
> + };
[Severity: High]
Are vreg_dp0_pwr through vreg_dp3_pwr missing enable-active-high?
For regulator-fixed nodes, of_gpio_set_polarity_by_property() in
drivers/gpio/gpiolib-of.c ignores the GPIO_ACTIVE_HIGH flag in the gpio
phandle specifier and forces OF_GPIO_ACTIVE_LOW unless enable-active-high
is present, so enabling these regulators will drive expander1 pins 7..10
low and keep 3.3V DP_PWR disabled on all four DisplayPort connectors.
[ ... ]
> +&pcie0 {
> + perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-0 = <&pcie0_default_state>;
> + pinctrl-names = "default";
> +
> + iommu-map = <0x0 &pcie_smmu 0x0 0x0 0x1>,
> + <0x100 &pcie_smmu 0x1 0x0 0x1>,
> + <0x208 &pcie_smmu 0x2 0x0 0x1>,
> + <0x210 &pcie_smmu 0x3 0x0 0x1>,
> + <0x218 &pcie_smmu 0x4 0x0 0x1>,
> + <0x300 &pcie_smmu 0x5 0x0 0x1>,
> + <0x400 &pcie_smmu 0x6 0x0 0x1>,
> + <0x500 &pcie_smmu 0x7 0x0 0x1>,
> + <0x501 &pcie_smmu 0x8 0x0 0x1>;
> +
> + status = "okay";
> +};
> +
> +&pcie0_phy {
> + vdda-phy-supply = <&vreg_l5a>;
> + vdda-pll-supply = <&vreg_l1c>;
> + vdda-qref-supply = <&vreg_l4a>;
> + vdda-refgen-supply = <&vreg_l7a>;
> +
> + status = "okay";
> +};
> +
> +&pcie1 {
> + perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-0 = <&pcie1_default_state>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
[Severity: High]
Should perst-gpios and wake-gpios on pcie0 and pcie1 be moved to the root
port nodes (pcieport0 and pcie1_port0) as reset-gpios and wake-gpios, with
wake-gpios changed to GPIO_ACTIVE_LOW?
pci_configure_of_wake_gpio() looks up wake-gpios on the root port pci_dev
OF node rather than the host bridge node, so wake-gpios on pcie0 and pcie1
is ignored; furthermore, WAKE# is an active-low line pulled up in
pcie0_default_state and pcie1_default_state, so GPIO_ACTIVE_HIGH would
configure a level-high wake IRQ (see e3a8a50e2a04 ("arm64: dts: qcom:
lemans: Move PCIe phy and GPIOs to root port node") and cd8d4803bba6
("arm64: dts: qcom: lemans: Fix PCIe WAKE# GPIO polarity")).
Keeping perst-gpios on the Root Complex node also triggers a runtime
warning in qcom_pcie_parse_perst() ("Reusing PERST# from Root Complex
node. DT needs to be fixed!") and adds duplicate reset descriptors to
port->perst for every descendant PCI bridge node.
> +
> +&pcie1_phy {
> + vdda-phy-supply = <&vreg_l5a>;
> + vdda-pll-supply = <&vreg_l1c>;
> + vdda-qref-supply = <&vreg_l4a>;
> + vdda-refgen-supply = <&vreg_l7a>;
> +
> + status = "okay";
> +};
[Severity: Low]
Does vdda-refgen-supply on pcie0_phy and pcie1_phy violate
qcom,sc8280xp-qmp-pcie-phy.yaml? The binding only permits
vdda-phy-supply, vdda-pll-supply, and vdda-qref-supply (and the SA8775P
QMP PCIe PHY driver only requests vdda-phy and vdda-pll).
> +
> +&pcieport0 {
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + pcie@0,0 {
> + compatible = "pci1179,0623";
> + reg = <0x10000 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + bus-range = <0x2 0xff>;
> +
> + vddc-supply = <&vreg_0p9>;
> + vdd18-supply = <&vreg_1p8>;
> + vdd09-supply = <&vreg_0p9>;
> + vddio1-supply = <&vreg_1p8>;
> + vddio2-supply = <&vreg_1p8>;
> + vddio18-supply = <&vreg_1p8>;
> + i2c-parent = <&i2c18 0x77>;
> + resx-gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
> + pinctrl-0 = <&tc9563_resx_n>;
> + pinctrl-names = "default";
> +
> + pcie@1,0 {
> + reg = <0x20800 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + bus-range = <0x3 0xff>;
> +
> + port {
> + tc9563_pcie1_ep: endpoint {};
> + };
> + };
[Severity: High]
Is pcie@1,0 missing compatible = "pciclass,0604"?
pci_pwrctrl_is_required() returns false when a PCI bridge node has no
compatible property starting with "pci", so pci-pwrctrl-slot will not bind
to this downstream port and the "pcie" power sequencer target on
wifi-bt-connector (pwrseq-pcie-m2) will never be enabled for the M.2 E-key
slot.
> +
> + pcie@2,0 {
> + reg = <0x21000 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + bus-range = <0x4 0xff>;
> + };
> +
> + pcie@3,0 {
> + reg = <0x21800 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + bus-range = <0x5 0xff>;
> +
> + pcie@0,0 {
> + reg = <0x50000 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + };
> +
> + pcie@0,1 {
> + reg = <0x50100 0x0 0x0 0x0 0x0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges;
> + };
> + };
[Severity: Medium]
Should the two integrated TC9563 Ethernet endpoint functions under
pcie@3,0 omit device_type = "pci", #address-cells, #size-cells, and
ranges (and be named ethernet@0,0 and ethernet@0,1 per
toshiba,tc9563.yaml)?
These functions are PCIe endpoints rather than PCI-to-PCI bridges, and
setting device_type = "pci" causes kernel OF PCI helpers that check
of_node_is_type(child, "pci") to treat them as bridges (see ca3027cfe8c7
("arm64: dts: qcom: lemans-evk-ifp-mezzanine: Clean up TC9563 switch
nodes")).
[ ... ]
> +&serdes0 {
> + phy-supply = <&vreg_l5a>;
> +
> + status = "okay";
> +};
> +
> +&serdes1 {
> + phy-supply = <&vreg_l5a>;
> +
> + status = "okay";
> +};
[Severity: High]
Should serdes0 and serdes1 specify vdda-0p9-supply = <&vreg_l4a> and
vdda-1p2-supply = <&vreg_l1c> instead of phy-supply = <&vreg_l5a>?
In drivers/phy/qualcomm/phy-qcom-sgmii-eth.c, qcom_dwmac_sgmii_phy_probe()
only requests "vdda-0p9" and "vdda-1p2" and ignores the deprecated
phy-supply property:
drivers/phy/qualcomm/phy-qcom-sgmii-eth.c:
static const struct regulator_bulk_data qcom_dwmac_sgmii_phy_vregs[] = {
{ .supply = "vdda-0p9", .init_load_uA = 46000 },
{ .supply = "vdda-1p2", .init_load_uA = 15000 },
};
Without vdda-0p9-supply and vdda-1p2-supply (as fixed for lemans-evk in
457cf65a7997 ("arm64: dts: qcom: lemans-evk: fix SerDes PHY regulator
supplies")), dummy regulators are used and the 0.9V and 1.2V SerDes rails
are not voted for when bringing up ethernet0 and ethernet1.
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261119-lemans-draco-final-changes-bringup-v3-0-db08f12f0cd5@oss.qualcomm.com?part=3
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2026-11-20 7:11 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-19 7:10 [PATCH v3 0/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board support Gopikishan Thawre
2026-11-19 7:10 ` [PATCH v3 1/3] dt-bindings: arm: qcom: Add LeMans Draco EVK board Gopikishan Thawre
2026-11-19 7:10 ` [PATCH v3 2/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK SoM platform Gopikishan Thawre
2026-11-20 7:11 ` sashiko-bot
2026-11-19 7:10 ` [PATCH v3 3/3] arm64: dts: qcom: lemans: Add LeMans Draco EVK board Gopikishan Thawre
2026-11-20 7:11 ` sashiko-bot
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.