* DMA-Bug using PCI-Passthrough (xen-3.1.0, gentoo amd64)
@ 2007-06-25 17:08 Stefan Neuwirth
2007-06-25 17:32 ` Ian Pratt
2007-06-25 17:57 ` Keir Fraser
0 siblings, 2 replies; 5+ messages in thread
From: Stefan Neuwirth @ 2007-06-25 17:08 UTC (permalink / raw)
To: xen-devel
Hi there,
I'm running xen-3.1.0 using gentoo amd64 for dom0. When starting a PV
guest domain everything is fine, up to the moment I try to configure
the ethernet device. The device is a real ethernet card that shown to
the guest by using pci passthrough.
~ # ifconfig eth4
eth4 Link encap:Ethernet HWaddr 00:00:D1:ED:14:02
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:22
~ # ifconfig eth4 192.168.0.131 netmask 255.255.255.0 up
----------- [cut here ] --------- [please bite here ] ---------
Kernel BUG at ...arch/x86_64/kernel/../../i386/kernel/pci-dma-xen.c:331
invalid opcode: 0000 [1] SMP
CPU 0
Modules linked in: usbcore starfire mii
Pid: 2978, comm: ifconfig Not tainted 2.6.18-xen #8
RIP: e030:[<ffffffff80210bdd>] [<ffffffff80210bdd>] dma_map_single+0x19a/0x1b2
RSP: e02b:ffff88001f517d48 EFLAGS: 00010292
RAX: 000000000000002f RBX: ffff88000019a810 RCX: ffff88001f516000
RDX: ffffffffff578000 RSI: 0000000000000001 RDI: ffffffff80561340
RBP: 00000004397da810 R08: 00000000a83abafa R09: 0000000000000000
R10: 0000000000000000 R11: 00000000000000c8 R12: 0000000000000600
R13: ffff88000007f070 R14: 0000000000000070 R15: ffff88001f7e0000
FS: 00002b009bbc36d0(0000) GS:ffffffff805e5000(0000) knlGS:0000000000000000
CS: e033 DS: 0000 ES: 0000
Process ifconfig (pid: 2978, threadinfo ffff88001f516000, task ffff8800001eb8c0)
Stack: ffff88001f7e05e0 ffff88001f6d37c0 ffff88001f7e05e0 ffff88001f7e0500
000000000000000f ffffffff880047e4 0000000000000000 ffffc20000280000
000000001fad8340 ffffc200002d0070 ffffc200002d0040 ffff88001f7e0000
Call Trace:
[<ffffffff880047e4>] :starfire:netdev_open+0x264/0x690
[<ffffffff80452ee0>] dev_open+0x2d/0x70
[<ffffffff80450ccb>] dev_change_flags+0x5c/0x11e
[<ffffffff8049394d>] devinet_ioctl+0x2a4/0x6a7
[<ffffffff80217749>] do_page_fault+0xdf8/0x1198
[<ffffffff80446c55>] sock_ioctl+0x214/0x239
[<ffffffff80287f71>] do_ioctl+0x21/0x79
[<ffffffff8028823d>] vfs_ioctl+0x274/0x28d
[<ffffffff802740e5>] fd_install+0x25/0x5f
[<ffffffff802882b1>] sys_ioctl+0x5b/0x7e
[<ffffffff80209f8a>] system_call+0x86/0x8b
[<ffffffff80209f04>] system_call+0x0/0x8b
Code: 0f 0b 68 78 15 4f 80 c2 4b 01 48 89 e8 48 83 c4 08 5b 5d 41
RIP [<ffffffff80210bdd>] dma_map_single+0x19a/0x1b2
RSP <ffff88001f517d48>
Segmentation fault
The same happens when using a tulip based ethernet card instead of the
adaptec starfire card.
Any hints?
Stefan
^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: DMA-Bug using PCI-Passthrough (xen-3.1.0, gentoo amd64)
2007-06-25 17:08 DMA-Bug using PCI-Passthrough (xen-3.1.0, gentoo amd64) Stefan Neuwirth
@ 2007-06-25 17:32 ` Ian Pratt
2007-06-25 18:05 ` Stefan Neuwirth
2007-06-25 17:57 ` Keir Fraser
1 sibling, 1 reply; 5+ messages in thread
From: Ian Pratt @ 2007-06-25 17:32 UTC (permalink / raw)
To: Stefan Neuwirth, xen-devel
> I'm running xen-3.1.0 using gentoo amd64 for dom0. When starting a PV
> guest domain everything is fine, up to the moment I try to configure
> the ethernet device. The device is a real ethernet card that shown to
> the guest by using pci passthrough.
Can you repro using the linux kernel that's part of the Xen 3.1.0
distribution?
Ian
> ~ # ifconfig eth4
> eth4 Link encap:Ethernet HWaddr 00:00:D1:ED:14:02
> BROADCAST MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
> Interrupt:22
>
> ~ # ifconfig eth4 192.168.0.131 netmask 255.255.255.0 up
> ----------- [cut here ] --------- [please bite here ] ---------
> Kernel BUG at
...arch/x86_64/kernel/../../i386/kernel/pci-dma-xen.c:331
> invalid opcode: 0000 [1] SMP
> CPU 0
> Modules linked in: usbcore starfire mii
> Pid: 2978, comm: ifconfig Not tainted 2.6.18-xen #8
> RIP: e030:[<ffffffff80210bdd>] [<ffffffff80210bdd>]
> dma_map_single+0x19a/0x1b2
> RSP: e02b:ffff88001f517d48 EFLAGS: 00010292
> RAX: 000000000000002f RBX: ffff88000019a810 RCX: ffff88001f516000
> RDX: ffffffffff578000 RSI: 0000000000000001 RDI: ffffffff80561340
> RBP: 00000004397da810 R08: 00000000a83abafa R09: 0000000000000000
> R10: 0000000000000000 R11: 00000000000000c8 R12: 0000000000000600
> R13: ffff88000007f070 R14: 0000000000000070 R15: ffff88001f7e0000
> FS: 00002b009bbc36d0(0000) GS:ffffffff805e5000(0000)
> knlGS:0000000000000000
> CS: e033 DS: 0000 ES: 0000
> Process ifconfig (pid: 2978, threadinfo ffff88001f516000, task
> ffff8800001eb8c0)
> Stack: ffff88001f7e05e0 ffff88001f6d37c0 ffff88001f7e05e0
> ffff88001f7e0500
> 000000000000000f ffffffff880047e4 0000000000000000 ffffc20000280000
> 000000001fad8340 ffffc200002d0070 ffffc200002d0040 ffff88001f7e0000
> Call Trace:
> [<ffffffff880047e4>] :starfire:netdev_open+0x264/0x690
> [<ffffffff80452ee0>] dev_open+0x2d/0x70
> [<ffffffff80450ccb>] dev_change_flags+0x5c/0x11e
> [<ffffffff8049394d>] devinet_ioctl+0x2a4/0x6a7
> [<ffffffff80217749>] do_page_fault+0xdf8/0x1198
> [<ffffffff80446c55>] sock_ioctl+0x214/0x239
> [<ffffffff80287f71>] do_ioctl+0x21/0x79
> [<ffffffff8028823d>] vfs_ioctl+0x274/0x28d
> [<ffffffff802740e5>] fd_install+0x25/0x5f
> [<ffffffff802882b1>] sys_ioctl+0x5b/0x7e
> [<ffffffff80209f8a>] system_call+0x86/0x8b
> [<ffffffff80209f04>] system_call+0x0/0x8b
>
>
> Code: 0f 0b 68 78 15 4f 80 c2 4b 01 48 89 e8 48 83 c4 08 5b 5d 41
> RIP [<ffffffff80210bdd>] dma_map_single+0x19a/0x1b2
> RSP <ffff88001f517d48>
> Segmentation fault
>
> The same happens when using a tulip based ethernet card instead of the
> adaptec starfire card.
>
> Any hints?
>
> Stefan
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: DMA-Bug using PCI-Passthrough (xen-3.1.0, gentoo amd64)
2007-06-25 17:08 DMA-Bug using PCI-Passthrough (xen-3.1.0, gentoo amd64) Stefan Neuwirth
2007-06-25 17:32 ` Ian Pratt
@ 2007-06-25 17:57 ` Keir Fraser
2007-06-25 18:49 ` Stefan Neuwirth
1 sibling, 1 reply; 5+ messages in thread
From: Keir Fraser @ 2007-06-25 17:57 UTC (permalink / raw)
To: Stefan Neuwirth, xen-devel
You might need to explicitly request a swiotlb ('swiotlb=force').
K.
On 25/6/07 18:08, "Stefan Neuwirth"
<neuwirt-xen-devel@trillian.hd.shuttle.de> wrote:
> Hi there,
>
> I'm running xen-3.1.0 using gentoo amd64 for dom0. When starting a PV
> guest domain everything is fine, up to the moment I try to configure
> the ethernet device. The device is a real ethernet card that shown to
> the guest by using pci passthrough.
>
> ~ # ifconfig eth4
> eth4 Link encap:Ethernet HWaddr 00:00:D1:ED:14:02
> BROADCAST MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:1000
> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
> Interrupt:22
>
> ~ # ifconfig eth4 192.168.0.131 netmask 255.255.255.0 up
> ----------- [cut here ] --------- [please bite here ] ---------
> Kernel BUG at ...arch/x86_64/kernel/../../i386/kernel/pci-dma-xen.c:331
> invalid opcode: 0000 [1] SMP
> CPU 0
> Modules linked in: usbcore starfire mii
> Pid: 2978, comm: ifconfig Not tainted 2.6.18-xen #8
> RIP: e030:[<ffffffff80210bdd>] [<ffffffff80210bdd>]
> dma_map_single+0x19a/0x1b2
> RSP: e02b:ffff88001f517d48 EFLAGS: 00010292
> RAX: 000000000000002f RBX: ffff88000019a810 RCX: ffff88001f516000
> RDX: ffffffffff578000 RSI: 0000000000000001 RDI: ffffffff80561340
> RBP: 00000004397da810 R08: 00000000a83abafa R09: 0000000000000000
> R10: 0000000000000000 R11: 00000000000000c8 R12: 0000000000000600
> R13: ffff88000007f070 R14: 0000000000000070 R15: ffff88001f7e0000
> FS: 00002b009bbc36d0(0000) GS:ffffffff805e5000(0000) knlGS:0000000000000000
> CS: e033 DS: 0000 ES: 0000
> Process ifconfig (pid: 2978, threadinfo ffff88001f516000, task
> ffff8800001eb8c0)
> Stack: ffff88001f7e05e0 ffff88001f6d37c0 ffff88001f7e05e0 ffff88001f7e0500
> 000000000000000f ffffffff880047e4 0000000000000000 ffffc20000280000
> 000000001fad8340 ffffc200002d0070 ffffc200002d0040 ffff88001f7e0000
> Call Trace:
> [<ffffffff880047e4>] :starfire:netdev_open+0x264/0x690
> [<ffffffff80452ee0>] dev_open+0x2d/0x70
> [<ffffffff80450ccb>] dev_change_flags+0x5c/0x11e
> [<ffffffff8049394d>] devinet_ioctl+0x2a4/0x6a7
> [<ffffffff80217749>] do_page_fault+0xdf8/0x1198
> [<ffffffff80446c55>] sock_ioctl+0x214/0x239
> [<ffffffff80287f71>] do_ioctl+0x21/0x79
> [<ffffffff8028823d>] vfs_ioctl+0x274/0x28d
> [<ffffffff802740e5>] fd_install+0x25/0x5f
> [<ffffffff802882b1>] sys_ioctl+0x5b/0x7e
> [<ffffffff80209f8a>] system_call+0x86/0x8b
> [<ffffffff80209f04>] system_call+0x0/0x8b
>
>
> Code: 0f 0b 68 78 15 4f 80 c2 4b 01 48 89 e8 48 83 c4 08 5b 5d 41
> RIP [<ffffffff80210bdd>] dma_map_single+0x19a/0x1b2
> RSP <ffff88001f517d48>
> Segmentation fault
>
> The same happens when using a tulip based ethernet card instead of the
> adaptec starfire card.
>
> Any hints?
>
> Stefan
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: DMA-Bug using PCI-Passthrough (xen-3.1.0, gentoo amd64)
2007-06-25 17:32 ` Ian Pratt
@ 2007-06-25 18:05 ` Stefan Neuwirth
0 siblings, 0 replies; 5+ messages in thread
From: Stefan Neuwirth @ 2007-06-25 18:05 UTC (permalink / raw)
To: Ian Pratt; +Cc: xen-devel
"Ian Pratt" <Ian.Pratt@cl.cam.ac.uk> writes:
>> I'm running xen-3.1.0 using gentoo amd64 for dom0. When starting a PV
>> guest domain everything is fine, up to the moment I try to configure
>> the ethernet device. The device is a real ethernet card that shown to
>> the guest by using pci passthrough.
>
> Can you repro using the linux kernel that's part of the Xen 3.1.0
> distribution?
It's a source build of xen-3.1.0 and the kernel is linux-2.6.18-xen
(same for dom0 and domU), I just changed some config items to get
things running on the machine.
Stefan
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: DMA-Bug using PCI-Passthrough (xen-3.1.0, gentoo amd64)
2007-06-25 17:57 ` Keir Fraser
@ 2007-06-25 18:49 ` Stefan Neuwirth
0 siblings, 0 replies; 5+ messages in thread
From: Stefan Neuwirth @ 2007-06-25 18:49 UTC (permalink / raw)
To: Keir Fraser; +Cc: xen-devel
Keir Fraser <keir@xensource.com> writes:
> You might need to explicitly request a swiotlb ('swiotlb=force').
Solved the problem, thank you.
Stefan
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2007-06-25 18:49 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2007-06-25 17:08 DMA-Bug using PCI-Passthrough (xen-3.1.0, gentoo amd64) Stefan Neuwirth
2007-06-25 17:32 ` Ian Pratt
2007-06-25 18:05 ` Stefan Neuwirth
2007-06-25 17:57 ` Keir Fraser
2007-06-25 18:49 ` Stefan Neuwirth
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.