* [ALSA - driver 0001957]: HP dv8000t hda-intel codec not recognized
@ 2006-03-26 20:18 bugtrack
0 siblings, 0 replies; 8+ messages in thread
From: bugtrack @ 2006-03-26 20:18 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1957>
======================================================================
Reported By: legoguy
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1957
Category: PCI - hda-intel
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Gentoo Linux
Kernel Version: 2.6.16
======================================================================
Date Submitted: 03-24-2006 02:18 CET
Last Modified: 03-26-2006 22:18 CEST
======================================================================
Summary: HP dv8000t hda-intel codec not recognized
Description:
lspci -nv:
00:1b.0 0403: 8086:27d8 (rev 01)
Subsystem: 103c:30a5
Flags: bus master, fast devsel, latency 0, IRQ 7
Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Capabilities: [70] Express Unknown type IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
cat /proc/asound/card0/codec\#0:
Codec: Generic 14f1 ID 5047
Address: 0
Vendor Id: 0x14f15047
Subsystem Id: 0x103c30a5
Revision Id: 0x100000
Default PCM: rates 0x040, bits 0x02, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x11 0x11]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x11 [Audio Output] wcaps 0x611: Stereo Digital
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x12 [Audio Input] wcaps 0x100d1b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=1
Amp-In vals: [0x0e 0x0e] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Connection: 6
0x19* 0x14 0x15 0x1a 0x16 0x10
Node 0x13 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1e 0x1e]
Pincap 0x081001c: OUT HP
Pin Default 0xc3111010: [Both] Speaker at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0xc0: OUT HP
Power: 0x0
Connection: 3
0x19* 0x10 0x16
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03811011: [Jack] Line In at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 2
0x19* 0x16
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03a11012: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x16 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x0860: IN
Pin Default 0x99330100: [Fixed] CD at Int ATAPI
Conn = ATAPI, Color = Unknown
Pin-ctls: 0x20: IN
Power: 0x0
Node 0x17 [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x08324: IN
Pin Default 0xb7a00100: [Fixed] Mic at Oth Mobile-In
Conn = Unknown, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Node 0x18 [Pin Complex] wcaps 0x400701: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x21440100: [Jack] SPDIF Out at Sep Rear
Conn = RCA, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Connection: 1
0x11
Node 0x19 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-In vals: [0x07 0x07] [0x07 0x07] [0x80 0x80] [0x17 0x17]
Power: 0x0
Connection: 4
0x10 0x1b 0x1a 0x16
Node 0x1a [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x1f, mute=0
Amp-Out vals: [0x00 0x00]
Power: 0x0
Connection: 3
0x15* 0x14 0x17
Node 0x1b [Audio Selector] wcaps 0x300501: Stereo
Power: 0x0
Connection: 2
0x14* 0x15
Node 0x1c [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x1d [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x08314: OUT
Pin Default 0x90100112: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x1e [Vendor Defined Widget] wcaps 0xf00000: Mono
I'm only given one out channel, Master, and one in channel, Mic, along
with Line and Capture. I cannot adjust the volume of the PC Speaker beep,
which is outrageously loud. From past experience with ALSA et al shouldn't
there be PCM and (since this supposedly supports S/PDIF with some special
jack) some other additional channels?
At any rate, this codec isn't detected/identified by the driver as
anything other than Generic.
======================================================================
----------------------------------------------------------------------
tiwai - 03-26-06 01:55
----------------------------------------------------------------------
It's a completely unknown codec. The vendor code is also uknown.
Do you have any hardware details?
Also, try to compile --with-debug=detect option. Then hda_generic.c will
give you a bit more debug prints.
----------------------------------------------------------------------
legoguy - 03-26-06 22:18
----------------------------------------------------------------------
Windows recognizes it as some kind of Conexant chip, at least that's the
driver that's installed for it.
--with-debug=detect didn't seem to make any change at all, no more
messages than before :/
Issue History
Date Modified Username Field Change
======================================================================
03-24-06 02:18 legoguy New Issue
03-24-06 02:18 legoguy Distribution => Gentoo Linux
03-24-06 02:18 legoguy Kernel Version => 2.6.16
03-24-06 03:06 legoguy Issue Monitored: legoguy
03-26-06 01:55 tiwai Note Added: 0008963
03-26-06 22:18 legoguy Note Added: 0008976
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by xPML, a groundbreaking scripting language
that extends applications into web and mobile media. Attend the live webcast
and join the prime developer group breaking into this new coding territory!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=110944&bid=241720&dat=121642
^ permalink raw reply [flat|nested] 8+ messages in thread* [ALSA - driver 0001957]: HP dv8000t hda-intel codec not recognized
@ 2006-06-20 17:46 bugtrack
0 siblings, 0 replies; 8+ messages in thread
From: bugtrack @ 2006-06-20 17:46 UTC (permalink / raw)
To: alsa-devel
The issue 0002174 has been set as DUPLICATE OF the following issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1957>
======================================================================
Reported By: legoguy
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1957
Category: PCI - hda-intel
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Gentoo Linux
Kernel Version: 2.6.16
======================================================================
Date Submitted: 03-24-2006 02:18 CET
Last Modified: 05-19-2006 09:06 CEST
======================================================================
Summary: HP dv8000t hda-intel codec not recognized
Description:
lspci -nv:
00:1b.0 0403: 8086:27d8 (rev 01)
Subsystem: 103c:30a5
Flags: bus master, fast devsel, latency 0, IRQ 7
Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Capabilities: [70] Express Unknown type IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
cat /proc/asound/card0/codec\#0:
Codec: Generic 14f1 ID 5047
Address: 0
Vendor Id: 0x14f15047
Subsystem Id: 0x103c30a5
Revision Id: 0x100000
Default PCM: rates 0x040, bits 0x02, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x11 0x11]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x11 [Audio Output] wcaps 0x611: Stereo Digital
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x12 [Audio Input] wcaps 0x100d1b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=1
Amp-In vals: [0x0e 0x0e] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Connection: 6
0x19* 0x14 0x15 0x1a 0x16 0x10
Node 0x13 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1e 0x1e]
Pincap 0x081001c: OUT HP
Pin Default 0xc3111010: [Both] Speaker at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0xc0: OUT HP
Power: 0x0
Connection: 3
0x19* 0x10 0x16
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03811011: [Jack] Line In at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 2
0x19* 0x16
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03a11012: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x16 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x0860: IN
Pin Default 0x99330100: [Fixed] CD at Int ATAPI
Conn = ATAPI, Color = Unknown
Pin-ctls: 0x20: IN
Power: 0x0
Node 0x17 [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x08324: IN
Pin Default 0xb7a00100: [Fixed] Mic at Oth Mobile-In
Conn = Unknown, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Node 0x18 [Pin Complex] wcaps 0x400701: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x21440100: [Jack] SPDIF Out at Sep Rear
Conn = RCA, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Connection: 1
0x11
Node 0x19 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-In vals: [0x07 0x07] [0x07 0x07] [0x80 0x80] [0x17 0x17]
Power: 0x0
Connection: 4
0x10 0x1b 0x1a 0x16
Node 0x1a [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x1f, mute=0
Amp-Out vals: [0x00 0x00]
Power: 0x0
Connection: 3
0x15* 0x14 0x17
Node 0x1b [Audio Selector] wcaps 0x300501: Stereo
Power: 0x0
Connection: 2
0x14* 0x15
Node 0x1c [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x1d [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x08314: OUT
Pin Default 0x90100112: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x1e [Vendor Defined Widget] wcaps 0xf00000: Mono
I'm only given one out channel, Master, and one in channel, Mic, along
with Line and Capture. I cannot adjust the volume of the PC Speaker beep,
which is outrageously loud. From past experience with ALSA et al shouldn't
there be PCM and (since this supposedly supports S/PDIF with some special
jack) some other additional channels?
At any rate, this codec isn't detected/identified by the driver as
anything other than Generic.
======================================================================
Relationships ID Summary
----------------------------------------------------------------------
has duplicate 0002174 No sound at all using snd-hda-intel / a...
======================================================================
----------------------------------------------------------------------
tiwai - 03-26-06 01:55
----------------------------------------------------------------------
It's a completely unknown codec. The vendor code is also uknown.
Do you have any hardware details?
Also, try to compile --with-debug=detect option. Then hda_generic.c will
give you a bit more debug prints.
----------------------------------------------------------------------
legoguy - 03-26-06 23:09
----------------------------------------------------------------------
Windows recognizes it as some kind of Conexant chip, at least that's the
driver that's installed for it.
--with-debug=detect didn't seem to make any change at all, no more
messages than before :/
I'm supposed to be looking in dmesg for debugging messages correct? all I
get when I load the modules is:
ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKG] -> GSI 7 (level, low)
-> IRQ 7
PCI: Setting latency timer of device 0000:00:1b.0 to 64
----------------------------------------------------------------------
tiwai - 04-20-06 15:39
----------------------------------------------------------------------
It should show more kernel messages but using KERN_DEBUG prefix. Check
/var/log/messages again.
----------------------------------------------------------------------
legoguy - 05-16-06 18:04
----------------------------------------------------------------------
`grep KERN_DEBUG /var/log/messages`
produces nothing, is there some option I need to enable elsewhere for
debugging to actually work? Right now I'm compiling the drivers with
--with-debug=full and I get nothing.
Note that this chip also works properly in OS X with the Azalia drivers
(once some PCI IDs are fiddled with), that might help here too... and
although this chip does work as a generic codec now, the maximum volume is
terribly low, not even close to what the Windows or OS X drivers can
output...
Additionally, mic in appears not to work, though I need to give it some
more thorough testing..
----------------------------------------------------------------------
tiwai - 05-18-06 11:40
----------------------------------------------------------------------
Of course, KERN_DEBUG prefix itself won't appear in the message. It's a
log-level. Compile with --with-debug=detect, as I asked.
----------------------------------------------------------------------
legoguy - 05-19-06 09:06
----------------------------------------------------------------------
Ah, alright, just had to set the logging level higher. Here.
../../alsa-kernel/pci/hda/hda_generic.c:568: AUD_IN = 12
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x12 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x14 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x1b IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x1b IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x1b
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x19 IDX=0x1
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x19 IDX=0x1
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x19
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x15 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:607: [Capture Source] NID=0x12,
#SRC=2
../../alsa-kernel/pci/hda/hda_generic.c:610: [Line] IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:610: [Mic] IDX=0x2
../../alsa-kernel/pci/hda/hda_generic.c:282: AUD_OUT found 10
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x19 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x19 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x19
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x13 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x13 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x13
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x13
../../alsa-kernel/pci/hda/hda_generic.c:668: [Capture Switch] NID=0x12,
DIR=IN, IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:688: [Capture Volume] NID=0x12,
DIR=IN, IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x12 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:675: [Master Playback Switch]
NID=0x10, DIR=OUT
../../alsa-kernel/pci/hda/hda_generic.c:695: [Master Playback Volume]
NID=0x10, DIR=OUT
Issue History
Date Modified Username Field Change
======================================================================
03-24-06 02:18 legoguy New Issue
03-24-06 02:18 legoguy Distribution => Gentoo Linux
03-24-06 02:18 legoguy Kernel Version => 2.6.16
03-24-06 03:06 legoguy Issue Monitored: legoguy
03-26-06 01:55 tiwai Note Added: 0008963
03-26-06 22:18 legoguy Note Added: 0008976
03-26-06 23:09 legoguy Note Edited: 0008976
04-20-06 15:39 tiwai Note Added: 0009389
05-16-06 17:59 legoguy Note Added: 0009840
05-16-06 17:59 legoguy Note Edited: 0009840
05-16-06 18:00 legoguy Note Edited: 0009840
05-16-06 18:03 legoguy Note Edited: 0009840
05-16-06 18:04 legoguy Note Edited: 0009840
05-18-06 11:40 tiwai Note Added: 0009865
05-19-06 09:06 legoguy Note Added: 0009875
06-20-06 19:45 rlrevell Relationship added has duplicate 0002174
======================================================================
^ permalink raw reply [flat|nested] 8+ messages in thread* [ALSA - driver 0001957]: HP dv8000t hda-intel codec not recognized
@ 2006-05-19 7:06 bugtrack
0 siblings, 0 replies; 8+ messages in thread
From: bugtrack @ 2006-05-19 7:06 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1957>
======================================================================
Reported By: legoguy
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1957
Category: PCI - hda-intel
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Gentoo Linux
Kernel Version: 2.6.16
======================================================================
Date Submitted: 03-24-2006 02:18 CET
Last Modified: 05-19-2006 09:06 CEST
======================================================================
Summary: HP dv8000t hda-intel codec not recognized
Description:
lspci -nv:
00:1b.0 0403: 8086:27d8 (rev 01)
Subsystem: 103c:30a5
Flags: bus master, fast devsel, latency 0, IRQ 7
Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Capabilities: [70] Express Unknown type IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
cat /proc/asound/card0/codec\#0:
Codec: Generic 14f1 ID 5047
Address: 0
Vendor Id: 0x14f15047
Subsystem Id: 0x103c30a5
Revision Id: 0x100000
Default PCM: rates 0x040, bits 0x02, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x11 0x11]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x11 [Audio Output] wcaps 0x611: Stereo Digital
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x12 [Audio Input] wcaps 0x100d1b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=1
Amp-In vals: [0x0e 0x0e] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Connection: 6
0x19* 0x14 0x15 0x1a 0x16 0x10
Node 0x13 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1e 0x1e]
Pincap 0x081001c: OUT HP
Pin Default 0xc3111010: [Both] Speaker at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0xc0: OUT HP
Power: 0x0
Connection: 3
0x19* 0x10 0x16
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03811011: [Jack] Line In at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 2
0x19* 0x16
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03a11012: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x16 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x0860: IN
Pin Default 0x99330100: [Fixed] CD at Int ATAPI
Conn = ATAPI, Color = Unknown
Pin-ctls: 0x20: IN
Power: 0x0
Node 0x17 [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x08324: IN
Pin Default 0xb7a00100: [Fixed] Mic at Oth Mobile-In
Conn = Unknown, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Node 0x18 [Pin Complex] wcaps 0x400701: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x21440100: [Jack] SPDIF Out at Sep Rear
Conn = RCA, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Connection: 1
0x11
Node 0x19 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-In vals: [0x07 0x07] [0x07 0x07] [0x80 0x80] [0x17 0x17]
Power: 0x0
Connection: 4
0x10 0x1b 0x1a 0x16
Node 0x1a [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x1f, mute=0
Amp-Out vals: [0x00 0x00]
Power: 0x0
Connection: 3
0x15* 0x14 0x17
Node 0x1b [Audio Selector] wcaps 0x300501: Stereo
Power: 0x0
Connection: 2
0x14* 0x15
Node 0x1c [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x1d [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x08314: OUT
Pin Default 0x90100112: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x1e [Vendor Defined Widget] wcaps 0xf00000: Mono
I'm only given one out channel, Master, and one in channel, Mic, along
with Line and Capture. I cannot adjust the volume of the PC Speaker beep,
which is outrageously loud. From past experience with ALSA et al shouldn't
there be PCM and (since this supposedly supports S/PDIF with some special
jack) some other additional channels?
At any rate, this codec isn't detected/identified by the driver as
anything other than Generic.
======================================================================
----------------------------------------------------------------------
tiwai - 05-18-06 11:40
----------------------------------------------------------------------
Of course, KERN_DEBUG prefix itself won't appear in the message. It's a
log-level. Compile with --with-debug=detect, as I asked.
----------------------------------------------------------------------
legoguy - 05-19-06 09:06
----------------------------------------------------------------------
Ah, alright, just had to set the logging level higher. Here.
../../alsa-kernel/pci/hda/hda_generic.c:568: AUD_IN = 12
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x12 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x14 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x1b IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x1b IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x1b
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x19 IDX=0x1
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x19 IDX=0x1
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x19
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x15 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:607: [Capture Source] NID=0x12,
#SRC=2
../../alsa-kernel/pci/hda/hda_generic.c:610: [Line] IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:610: [Mic] IDX=0x2
../../alsa-kernel/pci/hda/hda_generic.c:282: AUD_OUT found 10
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x19 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x19 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x19
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x13 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:226: UNMUTE IN: NID=0x13 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x13
../../alsa-kernel/pci/hda/hda_generic.c:210: UNMUTE OUT: NID=0x13
../../alsa-kernel/pci/hda/hda_generic.c:668: [Capture Switch] NID=0x12,
DIR=IN, IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:688: [Capture Volume] NID=0x12,
DIR=IN, IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:244: CONNECT: NID=0x12 IDX=0x0
../../alsa-kernel/pci/hda/hda_generic.c:675: [Master Playback Switch]
NID=0x10, DIR=OUT
../../alsa-kernel/pci/hda/hda_generic.c:695: [Master Playback Volume]
NID=0x10, DIR=OUT
Issue History
Date Modified Username Field Change
======================================================================
03-24-06 02:18 legoguy New Issue
03-24-06 02:18 legoguy Distribution => Gentoo Linux
03-24-06 02:18 legoguy Kernel Version => 2.6.16
03-24-06 03:06 legoguy Issue Monitored: legoguy
03-26-06 01:55 tiwai Note Added: 0008963
03-26-06 22:18 legoguy Note Added: 0008976
03-26-06 23:09 legoguy Note Edited: 0008976
04-20-06 15:39 tiwai Note Added: 0009389
05-16-06 17:59 legoguy Note Added: 0009840
05-16-06 17:59 legoguy Note Edited: 0009840
05-16-06 18:00 legoguy Note Edited: 0009840
05-16-06 18:03 legoguy Note Edited: 0009840
05-16-06 18:04 legoguy Note Edited: 0009840
05-18-06 11:40 tiwai Note Added: 0009865
05-19-06 09:06 legoguy Note Added: 0009875
======================================================================
-------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
^ permalink raw reply [flat|nested] 8+ messages in thread* [ALSA - driver 0001957]: HP dv8000t hda-intel codec not recognized
@ 2006-05-18 9:40 bugtrack
0 siblings, 0 replies; 8+ messages in thread
From: bugtrack @ 2006-05-18 9:40 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1957>
======================================================================
Reported By: legoguy
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1957
Category: PCI - hda-intel
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Gentoo Linux
Kernel Version: 2.6.16
======================================================================
Date Submitted: 03-24-2006 02:18 CET
Last Modified: 05-18-2006 11:40 CEST
======================================================================
Summary: HP dv8000t hda-intel codec not recognized
Description:
lspci -nv:
00:1b.0 0403: 8086:27d8 (rev 01)
Subsystem: 103c:30a5
Flags: bus master, fast devsel, latency 0, IRQ 7
Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Capabilities: [70] Express Unknown type IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
cat /proc/asound/card0/codec\#0:
Codec: Generic 14f1 ID 5047
Address: 0
Vendor Id: 0x14f15047
Subsystem Id: 0x103c30a5
Revision Id: 0x100000
Default PCM: rates 0x040, bits 0x02, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x11 0x11]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x11 [Audio Output] wcaps 0x611: Stereo Digital
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x12 [Audio Input] wcaps 0x100d1b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=1
Amp-In vals: [0x0e 0x0e] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Connection: 6
0x19* 0x14 0x15 0x1a 0x16 0x10
Node 0x13 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1e 0x1e]
Pincap 0x081001c: OUT HP
Pin Default 0xc3111010: [Both] Speaker at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0xc0: OUT HP
Power: 0x0
Connection: 3
0x19* 0x10 0x16
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03811011: [Jack] Line In at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 2
0x19* 0x16
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03a11012: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x16 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x0860: IN
Pin Default 0x99330100: [Fixed] CD at Int ATAPI
Conn = ATAPI, Color = Unknown
Pin-ctls: 0x20: IN
Power: 0x0
Node 0x17 [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x08324: IN
Pin Default 0xb7a00100: [Fixed] Mic at Oth Mobile-In
Conn = Unknown, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Node 0x18 [Pin Complex] wcaps 0x400701: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x21440100: [Jack] SPDIF Out at Sep Rear
Conn = RCA, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Connection: 1
0x11
Node 0x19 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-In vals: [0x07 0x07] [0x07 0x07] [0x80 0x80] [0x17 0x17]
Power: 0x0
Connection: 4
0x10 0x1b 0x1a 0x16
Node 0x1a [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x1f, mute=0
Amp-Out vals: [0x00 0x00]
Power: 0x0
Connection: 3
0x15* 0x14 0x17
Node 0x1b [Audio Selector] wcaps 0x300501: Stereo
Power: 0x0
Connection: 2
0x14* 0x15
Node 0x1c [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x1d [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x08314: OUT
Pin Default 0x90100112: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x1e [Vendor Defined Widget] wcaps 0xf00000: Mono
I'm only given one out channel, Master, and one in channel, Mic, along
with Line and Capture. I cannot adjust the volume of the PC Speaker beep,
which is outrageously loud. From past experience with ALSA et al shouldn't
there be PCM and (since this supposedly supports S/PDIF with some special
jack) some other additional channels?
At any rate, this codec isn't detected/identified by the driver as
anything other than Generic.
======================================================================
----------------------------------------------------------------------
legoguy - 05-16-06 18:04
----------------------------------------------------------------------
`grep KERN_DEBUG /var/log/messages`
produces nothing, is there some option I need to enable elsewhere for
debugging to actually work? Right now I'm compiling the drivers with
--with-debug=full and I get nothing.
Note that this chip also works properly in OS X with the Azalia drivers
(once some PCI IDs are fiddled with), that might help here too... and
although this chip does work as a generic codec now, the maximum volume is
terribly low, not even close to what the Windows or OS X drivers can
output...
Additionally, mic in appears not to work, though I need to give it some
more thorough testing..
----------------------------------------------------------------------
tiwai - 05-18-06 11:40
----------------------------------------------------------------------
Of course, KERN_DEBUG prefix itself won't appear in the message. It's a
log-level. Compile with --with-debug=detect, as I asked.
Issue History
Date Modified Username Field Change
======================================================================
03-24-06 02:18 legoguy New Issue
03-24-06 02:18 legoguy Distribution => Gentoo Linux
03-24-06 02:18 legoguy Kernel Version => 2.6.16
03-24-06 03:06 legoguy Issue Monitored: legoguy
03-26-06 01:55 tiwai Note Added: 0008963
03-26-06 22:18 legoguy Note Added: 0008976
03-26-06 23:09 legoguy Note Edited: 0008976
04-20-06 15:39 tiwai Note Added: 0009389
05-16-06 17:59 legoguy Note Added: 0009840
05-16-06 17:59 legoguy Note Edited: 0009840
05-16-06 18:00 legoguy Note Edited: 0009840
05-16-06 18:03 legoguy Note Edited: 0009840
05-16-06 18:04 legoguy Note Edited: 0009840
05-18-06 11:40 tiwai Note Added: 0009865
======================================================================
-------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
^ permalink raw reply [flat|nested] 8+ messages in thread* [ALSA - driver 0001957]: HP dv8000t hda-intel codec not recognized
@ 2006-05-16 15:59 bugtrack
0 siblings, 0 replies; 8+ messages in thread
From: bugtrack @ 2006-05-16 15:59 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1957>
======================================================================
Reported By: legoguy
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1957
Category: PCI - hda-intel
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Gentoo Linux
Kernel Version: 2.6.16
======================================================================
Date Submitted: 03-24-2006 02:18 CET
Last Modified: 05-16-2006 17:59 CEST
======================================================================
Summary: HP dv8000t hda-intel codec not recognized
Description:
lspci -nv:
00:1b.0 0403: 8086:27d8 (rev 01)
Subsystem: 103c:30a5
Flags: bus master, fast devsel, latency 0, IRQ 7
Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Capabilities: [70] Express Unknown type IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
cat /proc/asound/card0/codec\#0:
Codec: Generic 14f1 ID 5047
Address: 0
Vendor Id: 0x14f15047
Subsystem Id: 0x103c30a5
Revision Id: 0x100000
Default PCM: rates 0x040, bits 0x02, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x11 0x11]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x11 [Audio Output] wcaps 0x611: Stereo Digital
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x12 [Audio Input] wcaps 0x100d1b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=1
Amp-In vals: [0x0e 0x0e] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Connection: 6
0x19* 0x14 0x15 0x1a 0x16 0x10
Node 0x13 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1e 0x1e]
Pincap 0x081001c: OUT HP
Pin Default 0xc3111010: [Both] Speaker at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0xc0: OUT HP
Power: 0x0
Connection: 3
0x19* 0x10 0x16
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03811011: [Jack] Line In at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 2
0x19* 0x16
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03a11012: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x16 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x0860: IN
Pin Default 0x99330100: [Fixed] CD at Int ATAPI
Conn = ATAPI, Color = Unknown
Pin-ctls: 0x20: IN
Power: 0x0
Node 0x17 [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x08324: IN
Pin Default 0xb7a00100: [Fixed] Mic at Oth Mobile-In
Conn = Unknown, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Node 0x18 [Pin Complex] wcaps 0x400701: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x21440100: [Jack] SPDIF Out at Sep Rear
Conn = RCA, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Connection: 1
0x11
Node 0x19 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-In vals: [0x07 0x07] [0x07 0x07] [0x80 0x80] [0x17 0x17]
Power: 0x0
Connection: 4
0x10 0x1b 0x1a 0x16
Node 0x1a [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x1f, mute=0
Amp-Out vals: [0x00 0x00]
Power: 0x0
Connection: 3
0x15* 0x14 0x17
Node 0x1b [Audio Selector] wcaps 0x300501: Stereo
Power: 0x0
Connection: 2
0x14* 0x15
Node 0x1c [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x1d [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x08314: OUT
Pin Default 0x90100112: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x1e [Vendor Defined Widget] wcaps 0xf00000: Mono
I'm only given one out channel, Master, and one in channel, Mic, along
with Line and Capture. I cannot adjust the volume of the PC Speaker beep,
which is outrageously loud. From past experience with ALSA et al shouldn't
there be PCM and (since this supposedly supports S/PDIF with some special
jack) some other additional channels?
At any rate, this codec isn't detected/identified by the driver as
anything other than Generic.
======================================================================
----------------------------------------------------------------------
tiwai - 04-20-06 15:39
----------------------------------------------------------------------
It should show more kernel messages but using KERN_DEBUG prefix. Check
/var/log/messages again.
----------------------------------------------------------------------
legoguy - 05-16-06 17:59
----------------------------------------------------------------------
`grep KERN_DEBUG /var/log/messages`
produces nothing, is there some option I need to enable elsewhere for
debugging to actually work? Right now I'm compiling the drivers with
--with-debug=all and I get nothing.
Note that this card also works properly in OS X with the Azalia drivers,
that might help here too... and although this card does work as a generic
chip now, the maximum volume is terribly low, not even close to what the
Windows or OS X drivers can output...
Issue History
Date Modified Username Field Change
======================================================================
03-24-06 02:18 legoguy New Issue
03-24-06 02:18 legoguy Distribution => Gentoo Linux
03-24-06 02:18 legoguy Kernel Version => 2.6.16
03-24-06 03:06 legoguy Issue Monitored: legoguy
03-26-06 01:55 tiwai Note Added: 0008963
03-26-06 22:18 legoguy Note Added: 0008976
03-26-06 23:09 legoguy Note Edited: 0008976
04-20-06 15:39 tiwai Note Added: 0009389
05-16-06 17:59 legoguy Note Added: 0009840
======================================================================
-------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
^ permalink raw reply [flat|nested] 8+ messages in thread* [ALSA - driver 0001957]: HP dv8000t hda-intel codec not recognized
@ 2006-04-20 13:39 bugtrack
0 siblings, 0 replies; 8+ messages in thread
From: bugtrack @ 2006-04-20 13:39 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1957>
======================================================================
Reported By: legoguy
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1957
Category: PCI - hda-intel
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Gentoo Linux
Kernel Version: 2.6.16
======================================================================
Date Submitted: 03-24-2006 02:18 CET
Last Modified: 04-20-2006 15:39 CEST
======================================================================
Summary: HP dv8000t hda-intel codec not recognized
Description:
lspci -nv:
00:1b.0 0403: 8086:27d8 (rev 01)
Subsystem: 103c:30a5
Flags: bus master, fast devsel, latency 0, IRQ 7
Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Capabilities: [70] Express Unknown type IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
cat /proc/asound/card0/codec\#0:
Codec: Generic 14f1 ID 5047
Address: 0
Vendor Id: 0x14f15047
Subsystem Id: 0x103c30a5
Revision Id: 0x100000
Default PCM: rates 0x040, bits 0x02, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x11 0x11]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x11 [Audio Output] wcaps 0x611: Stereo Digital
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x12 [Audio Input] wcaps 0x100d1b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=1
Amp-In vals: [0x0e 0x0e] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Connection: 6
0x19* 0x14 0x15 0x1a 0x16 0x10
Node 0x13 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1e 0x1e]
Pincap 0x081001c: OUT HP
Pin Default 0xc3111010: [Both] Speaker at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0xc0: OUT HP
Power: 0x0
Connection: 3
0x19* 0x10 0x16
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03811011: [Jack] Line In at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 2
0x19* 0x16
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03a11012: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x16 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x0860: IN
Pin Default 0x99330100: [Fixed] CD at Int ATAPI
Conn = ATAPI, Color = Unknown
Pin-ctls: 0x20: IN
Power: 0x0
Node 0x17 [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x08324: IN
Pin Default 0xb7a00100: [Fixed] Mic at Oth Mobile-In
Conn = Unknown, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Node 0x18 [Pin Complex] wcaps 0x400701: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x21440100: [Jack] SPDIF Out at Sep Rear
Conn = RCA, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Connection: 1
0x11
Node 0x19 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-In vals: [0x07 0x07] [0x07 0x07] [0x80 0x80] [0x17 0x17]
Power: 0x0
Connection: 4
0x10 0x1b 0x1a 0x16
Node 0x1a [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x1f, mute=0
Amp-Out vals: [0x00 0x00]
Power: 0x0
Connection: 3
0x15* 0x14 0x17
Node 0x1b [Audio Selector] wcaps 0x300501: Stereo
Power: 0x0
Connection: 2
0x14* 0x15
Node 0x1c [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x1d [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x08314: OUT
Pin Default 0x90100112: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x1e [Vendor Defined Widget] wcaps 0xf00000: Mono
I'm only given one out channel, Master, and one in channel, Mic, along
with Line and Capture. I cannot adjust the volume of the PC Speaker beep,
which is outrageously loud. From past experience with ALSA et al shouldn't
there be PCM and (since this supposedly supports S/PDIF with some special
jack) some other additional channels?
At any rate, this codec isn't detected/identified by the driver as
anything other than Generic.
======================================================================
----------------------------------------------------------------------
legoguy - 03-26-06 23:09
----------------------------------------------------------------------
Windows recognizes it as some kind of Conexant chip, at least that's the
driver that's installed for it.
--with-debug=detect didn't seem to make any change at all, no more
messages than before :/
I'm supposed to be looking in dmesg for debugging messages correct? all I
get when I load the modules is:
ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKG] -> GSI 7 (level, low)
-> IRQ 7
PCI: Setting latency timer of device 0000:00:1b.0 to 64
----------------------------------------------------------------------
tiwai - 04-20-06 15:39
----------------------------------------------------------------------
It should show more kernel messages but using KERN_DEBUG prefix. Check
/var/log/messages again.
Issue History
Date Modified Username Field Change
======================================================================
03-24-06 02:18 legoguy New Issue
03-24-06 02:18 legoguy Distribution => Gentoo Linux
03-24-06 02:18 legoguy Kernel Version => 2.6.16
03-24-06 03:06 legoguy Issue Monitored: legoguy
03-26-06 01:55 tiwai Note Added: 0008963
03-26-06 22:18 legoguy Note Added: 0008976
03-26-06 23:09 legoguy Note Edited: 0008976
04-20-06 15:39 tiwai Note Added: 0009389
======================================================================
-------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
^ permalink raw reply [flat|nested] 8+ messages in thread* [ALSA - driver 0001957]: HP dv8000t hda-intel codec not recognized
@ 2006-03-26 0:55 bugtrack
0 siblings, 0 replies; 8+ messages in thread
From: bugtrack @ 2006-03-26 0:55 UTC (permalink / raw)
To: alsa-devel
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1957>
======================================================================
Reported By: legoguy
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1957
Category: PCI - hda-intel
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Gentoo Linux
Kernel Version: 2.6.16
======================================================================
Date Submitted: 03-24-2006 02:18 CET
Last Modified: 03-26-2006 01:55 CET
======================================================================
Summary: HP dv8000t hda-intel codec not recognized
Description:
lspci -nv:
00:1b.0 0403: 8086:27d8 (rev 01)
Subsystem: 103c:30a5
Flags: bus master, fast devsel, latency 0, IRQ 7
Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Capabilities: [70] Express Unknown type IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
cat /proc/asound/card0/codec\#0:
Codec: Generic 14f1 ID 5047
Address: 0
Vendor Id: 0x14f15047
Subsystem Id: 0x103c30a5
Revision Id: 0x100000
Default PCM: rates 0x040, bits 0x02, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x11 0x11]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x11 [Audio Output] wcaps 0x611: Stereo Digital
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x12 [Audio Input] wcaps 0x100d1b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=1
Amp-In vals: [0x0e 0x0e] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Connection: 6
0x19* 0x14 0x15 0x1a 0x16 0x10
Node 0x13 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1e 0x1e]
Pincap 0x081001c: OUT HP
Pin Default 0xc3111010: [Both] Speaker at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0xc0: OUT HP
Power: 0x0
Connection: 3
0x19* 0x10 0x16
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03811011: [Jack] Line In at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 2
0x19* 0x16
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03a11012: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x16 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x0860: IN
Pin Default 0x99330100: [Fixed] CD at Int ATAPI
Conn = ATAPI, Color = Unknown
Pin-ctls: 0x20: IN
Power: 0x0
Node 0x17 [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x08324: IN
Pin Default 0xb7a00100: [Fixed] Mic at Oth Mobile-In
Conn = Unknown, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Node 0x18 [Pin Complex] wcaps 0x400701: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x21440100: [Jack] SPDIF Out at Sep Rear
Conn = RCA, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Connection: 1
0x11
Node 0x19 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-In vals: [0x07 0x07] [0x07 0x07] [0x80 0x80] [0x17 0x17]
Power: 0x0
Connection: 4
0x10 0x1b 0x1a 0x16
Node 0x1a [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x1f, mute=0
Amp-Out vals: [0x00 0x00]
Power: 0x0
Connection: 3
0x15* 0x14 0x17
Node 0x1b [Audio Selector] wcaps 0x300501: Stereo
Power: 0x0
Connection: 2
0x14* 0x15
Node 0x1c [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x1d [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x08314: OUT
Pin Default 0x90100112: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x1e [Vendor Defined Widget] wcaps 0xf00000: Mono
I'm only given one out channel, Master, and one in channel, Mic, along
with Line and Capture. I cannot adjust the volume of the PC Speaker beep,
which is outrageously loud. From past experience with ALSA et al shouldn't
there be PCM and (since this supposedly supports S/PDIF with some special
jack) some other additional channels?
At any rate, this codec isn't detected/identified by the driver as
anything other than Generic.
======================================================================
----------------------------------------------------------------------
tiwai - 03-26-06 01:55
----------------------------------------------------------------------
It's a completely unknown codec. The vendor code is also uknown.
Do you have any hardware details?
Also, try to compile --with-debug=detect option. Then hda_generic.c will
give you a bit more debug prints.
Issue History
Date Modified Username Field Change
======================================================================
03-24-06 02:18 legoguy New Issue
03-24-06 02:18 legoguy Distribution => Gentoo Linux
03-24-06 02:18 legoguy Kernel Version => 2.6.16
03-24-06 03:06 legoguy Issue Monitored: legoguy
03-26-06 01:55 tiwai Note Added: 0008963
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by xPML, a groundbreaking scripting language
that extends applications into web and mobile media. Attend the live webcast
and join the prime developer group breaking into this new coding territory!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=110944&bid=241720&dat=121642
^ permalink raw reply [flat|nested] 8+ messages in thread* [ALSA - driver 0001957]: HP dv8000t hda-intel codec not recognized
@ 2006-03-24 1:18 bugtrack
0 siblings, 0 replies; 8+ messages in thread
From: bugtrack @ 2006-03-24 1:18 UTC (permalink / raw)
To: alsa-devel
The following issue has been SUBMITTED.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1957>
======================================================================
Reported By: legoguy
Assigned To: tiwai
======================================================================
Project: ALSA - driver
Issue ID: 1957
Category: PCI - hda-intel
Reproducibility: always
Severity: minor
Priority: normal
Status: assigned
Distribution: Gentoo Linux
Kernel Version: 2.6.16
======================================================================
Date Submitted: 03-24-2006 02:18 CET
Last Modified: 03-24-2006 02:18 CET
======================================================================
Summary: HP dv8000t hda-intel codec not recognized
Description:
lspci -nv:
00:1b.0 0403: 8086:27d8 (rev 01)
Subsystem: 103c:30a5
Flags: bus master, fast devsel, latency 0, IRQ 7
Memory at d2400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Capabilities: [70] Express Unknown type IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [130] Unknown (5)
cat /proc/asound/card0/codec\#0:
Codec: Generic 14f1 ID 5047
Address: 0
Vendor Id: 0x14f15047
Subsystem Id: 0x103c30a5
Revision Id: 0x100000
Default PCM: rates 0x040, bits 0x02, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x10 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x11 0x11]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x11 [Audio Output] wcaps 0x611: Stereo Digital
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x12 [Audio Input] wcaps 0x100d1b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x0e, stepsize=0x05, mute=1
Amp-In vals: [0x0e 0x0e] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Connection: 6
0x19* 0x14 0x15 0x1a 0x16 0x10
Node 0x13 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1e 0x1e]
Pincap 0x081001c: OUT HP
Pin Default 0xc3111010: [Both] Speaker at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0xc0: OUT HP
Power: 0x0
Connection: 3
0x19* 0x10 0x16
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03811011: [Jack] Line In at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 2
0x19* 0x16
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x0833c: IN OUT HP
Pin Default 0x03a11012: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
Pin-ctls: 0x20: IN
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x16 [Pin Complex] wcaps 0x400401: Stereo
Pincap 0x0860: IN
Pin Default 0x99330100: [Fixed] CD at Int ATAPI
Conn = ATAPI, Color = Unknown
Pin-ctls: 0x20: IN
Power: 0x0
Node 0x17 [Pin Complex] wcaps 0x400481: Stereo
Pincap 0x08324: IN
Pin Default 0xb7a00100: [Fixed] Mic at Oth Mobile-In
Conn = Unknown, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Node 0x18 [Pin Complex] wcaps 0x400701: Stereo Digital
Pincap 0x0810: OUT
Pin Default 0x21440100: [Jack] SPDIF Out at Sep Rear
Conn = RCA, Color = Unknown
Pin-ctls: 0x00:
Power: 0x0
Connection: 1
0x11
Node 0x19 [Audio Mixer] wcaps 0x20050b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-In vals: [0x07 0x07] [0x07 0x07] [0x80 0x80] [0x17 0x17]
Power: 0x0
Connection: 4
0x10 0x1b 0x1a 0x16
Node 0x1a [Audio Selector] wcaps 0x30050d: Stereo Amp-Out
Amp-Out caps: ofs=0x00, nsteps=0x03, stepsize=0x1f, mute=0
Amp-Out vals: [0x00 0x00]
Power: 0x0
Connection: 3
0x15* 0x14 0x17
Node 0x1b [Audio Selector] wcaps 0x300501: Stereo
Power: 0x0
Connection: 2
0x14* 0x15
Node 0x1c [Audio Output] wcaps 0x41d: Stereo Amp-Out
Amp-Out caps: ofs=0x17, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x80 0x80]
PCM: rates 0x040, bits 0x02, types 0x1
Power: 0x0
Node 0x1d [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Amp-Out caps: ofs=0x1f, nsteps=0x1e, stepsize=0x05, mute=1
Amp-Out vals: [0x1f 0x1f]
Pincap 0x08314: OUT
Pin Default 0x90100112: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Power: 0x0
Connection: 3
0x1c 0x19* 0x16
Node 0x1e [Vendor Defined Widget] wcaps 0xf00000: Mono
I'm only given one out channel, Master, and one in channel, Mic, along
with Line and Capture. I cannot adjust the volume of the PC Speaker beep,
which is outrageously loud. From past experience with ALSA et al shouldn't
there be PCM and (since this supposedly supports S/PDIF with some special
jack) some other additional channels?
At any rate, this codec isn't detected/identified by the driver as
anything other than Generic.
======================================================================
Issue History
Date Modified Username Field Change
======================================================================
03-24-06 02:18 legoguy New Issue
03-24-06 02:18 legoguy Distribution => Gentoo Linux
03-24-06 02:18 legoguy Kernel Version => 2.6.16
======================================================================
-------------------------------------------------------
This SF.Net email is sponsored by xPML, a groundbreaking scripting language
that extends applications into web and mobile media. Attend the live webcast
and join the prime developer group breaking into this new coding territory!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=110944&bid=241720&dat=121642
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2006-06-20 17:46 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2006-03-26 20:18 [ALSA - driver 0001957]: HP dv8000t hda-intel codec not recognized bugtrack
-- strict thread matches above, loose matches on Subject: below --
2006-06-20 17:46 bugtrack
2006-05-19 7:06 bugtrack
2006-05-18 9:40 bugtrack
2006-05-16 15:59 bugtrack
2006-04-20 13:39 bugtrack
2006-03-26 0:55 bugtrack
2006-03-24 1:18 bugtrack
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox