From: Shaw Terwilliger <sterwill@sourcegear.com>
To: Tobin Davis <tdavis@dsl-only.net>
Cc: alsa-devel@lists.sourceforge.net
Subject: Re: Intel HDA on Mac Pro
Date: Mon, 04 Dec 2006 15:02:45 -0600 [thread overview]
Message-ID: <45748CF5.8040800@sourcegear.com> (raw)
In-Reply-To: <1165265511.32312.86.camel@razman>
Tobin Davis wrote:
> Well, to start, we'll need to know the exact codec information. Type
> "cat /proc/asound/card0/codec*" to find out. To add your specific
> configuration to the driver (if it isn't in the tree already), we'll
> also need the subsystem ID from lspci. Assuming the audio device is on
> pci bus 0:1b.0, type 'lspci -s 0:1b -vn" to get that.
I should have included those in my first message, sorry (they're at the
bottom of this one). Thanks for your help.
>From there, it's probably just a matter of trying different config
> models from the ALSA-Configuration.txt (it's in
> alsa-driver-1.0.13/alsa-kernel/Documentation if you downloaded the
> driver source, or it is in the kernel documentation).
I've tried a dozen or so, and they all seem to load correctly and
correctly influence the mixers. I'll verify I was trying the right ones.
hansen:~% sudo lspci -s 0:1b -vn
00:1b.0 0403: 8086:269a (rev 09)
Flags: bus master, fast devsel, latency 0, IRQ 225
Memory at 92f00000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Capabilities: [70] Express Unknown type IRQ 0
Codec: Realtek ALC885
Address: 0
Vendor Id: 0x10ec0885
Subsystem Id: 0x106b0c00
Revision Id: 0x100103
Default PCM: rates 0x560, bits 0x0e, types 0x1
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
Node 0x02 [Audio Output] wcaps 0x11: Stereo
PCM: rates 0x560, bits 0x0e, types 0x1
Node 0x03 [Audio Output] wcaps 0x11: Stereo
PCM: rates 0x560, bits 0x0e, types 0x1
Node 0x04 [Audio Output] wcaps 0x11: Stereo
PCM: rates 0x560, bits 0x0e, types 0x1
Node 0x05 [Audio Output] wcaps 0x11: Stereo
PCM: rates 0x560, bits 0x0e, types 0x1
Node 0x06 [Audio Output] wcaps 0x211: Stereo Digital
PCM: rates 0x5e0, bits 0x1e, types 0x1
Node 0x07 [Audio Input] wcaps 0x10011b: Stereo Amp-In
Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1
Amp-In vals: [0x80 0x80]
PCM: rates 0x560, bits 0x0e, types 0x1
Connection: 1
0x24
Node 0x08 [Audio Input] wcaps 0x10011b: Stereo Amp-In
Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1
Amp-In vals: [0x80 0x80]
PCM: rates 0x560, bits 0x0e, types 0x1
Connection: 1
0x23
Node 0x09 [Audio Input] wcaps 0x10011b: Stereo Amp-In
Amp-In caps: ofs=0x10, nsteps=0x2e, stepsize=0x03, mute=1
Amp-In vals: [0x80 0x80]
PCM: rates 0x560, bits 0x0e, types 0x1
Connection: 1
0x22
Node 0x0a [Audio Input] wcaps 0x100391: Stereo Digital
PCM: rates 0x560, bits 0x1e, types 0x1
Connection: 1
0x1f
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
Amp-In vals: [0x80 0x80] [0x80 0x80] [0x95 0x95] [0x97 0x97] [0x00
0x00] [0x10 0x10] [0x97 0x97] [0x97 0x97] [0x97 0x97] [0x97 0x97]
Connection: 10
0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17
Node 0x0c [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
Amp-Out vals: [0x33 0x33]
Connection: 2
0x02 0x0b
Node 0x0d [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x80 0x80] [0x80 0x80]
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 2
0x03 0x0b
Node 0x0e [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x80 0x80] [0x80 0x80]
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 2
0x04 0x0b
Node 0x0f [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x80 0x80] [0x80 0x80]
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
Amp-Out vals: [0x00 0x00]
Connection: 2
0x05 0x0b
Node 0x10 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x12 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x14 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x08373c: IN OUT HP Detect
Pin Default 0x400000f0: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x15 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x08373c: IN OUT HP Detect
Pin Default 0x01014150: [Jack] Line Out at Ext Rear
Conn = 1/8, Color = Green
Pin-ctls: 0x40: OUT
Connection: 5
0x0c 0x0d* 0x0e 0x0f 0x26
Node 0x16 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x88a0967c, nsteps=0x03, stepsize=0x100, mute=25
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x083c: IN OUT HP Detect
Pin Default 0x400000f0: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Connection: 5
0x0c 0x0d 0x0e* 0x0f 0x26
Node 0x17 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x083c: IN OUT HP Detect
Pin Default 0x400000f0: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x40: OUT
Connection: 5
0x0c 0x0d 0x0e 0x0f* 0x26
Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x08373c: IN OUT HP Detect
Pin Default 0x02214040: [Jack] HP Out at Ext Front
Conn = 1/8, Color = Green
Pin-ctls: 0x24: IN
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x19 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x08373c: IN OUT HP Detect
Pin Default 0x01813110: [Jack] Line In at Ext Rear
Conn = 1/8, Color = Blue
Pin-ctls: 0x24: IN
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1a [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x08373c: IN OUT HP Detect
Pin Default 0x90100130: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x20: IN
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1b [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x08373c: IN OUT HP Detect
Pin Default 0x400000f0: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0xc0: OUT HP
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
Node 0x1c [Pin Complex] wcaps 0x400001: Stereo
Pincap 0x0820: IN
Pin Default 0x400000f0: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x20: IN
Node 0x1d [Pin Complex] wcaps 0x400000: Mono
Pincap 0x0820: IN
Pin Default 0x400000f0: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
Pin-ctls: 0x20: IN
Node 0x1e [Pin Complex] wcaps 0x400300: Mono Digital
Pincap 0x0810: OUT
Pin Default 0x0145e160: [Jack] SPDIF Out at Ext Rear
Conn = Optical, Color = White
Pin-ctls: 0x40: OUT
Connection: 1
0x06
Node 0x1f [Pin Complex] wcaps 0x400200: Mono Digital
Pincap 0x0820: IN
Pin Default 0x01c5e120: [Jack] SPDIF In at Ext Rear
Conn = Optical, Color = White
Pin-ctls: 0x20: IN
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Node 0x21 [Volume Knob Widget] wcaps 0x600080: Mono
Node 0x22 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80]
Connection: 11
0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b
Node 0x23 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x88a0967c, nsteps=0x03, stepsize=0x100, mute=25
Amp-In vals: [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80]
Connection: 11
0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b
Node 0x24 [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x80 0x80] [0x80 0x80] [0x00 0x00] [0x80 0x80] [0x80
0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80
0x80]
Connection: 11
0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b
Node 0x25 [Audio Output] wcaps 0x11: Stereo
PCM: rates 0x560, bits 0x0e, types 0x1
Node 0x26 [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80]
Amp-Out caps: ofs=0x40, nsteps=0x40, stepsize=0x03, mute=0
Amp-Out vals: [0x40 0x40]
Connection: 2
0x25 0x0b
--
Shaw Terwilliger <sterwill@sourcegear.com>
SourceGear LLC
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
next prev parent reply other threads:[~2006-12-04 21:02 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-12-04 20:34 Intel HDA on Mac Pro Shaw Terwilliger
2006-12-04 20:51 ` Tobin Davis
2006-12-04 21:02 ` Shaw Terwilliger [this message]
2006-12-04 23:45 ` Tobin Davis
2006-12-05 0:19 ` Shaw Terwilliger
2006-12-05 0:30 ` Tobin Davis
2006-12-05 4:02 ` Shaw Terwilliger
[not found] ` <457828D7.4020908@teamprise.com>
2006-12-07 14:51 ` Tobin Davis
2006-12-07 23:46 ` Tobin Davis
2006-12-08 19:39 ` Shaw Terwilliger
2006-12-10 16:16 ` Tobin Davis
2006-12-11 14:43 ` Shaw Terwilliger
2006-12-11 16:33 ` Tobin Davis
2006-12-11 16:52 ` Shaw Terwilliger
2006-12-11 17:05 ` Tobin Davis
2006-12-11 17:13 ` Shaw Terwilliger
2006-12-11 17:43 ` Tobin Davis
2006-12-11 19:09 ` Shaw Terwilliger
2006-12-11 22:10 ` Richard
2006-12-11 22:55 ` Tobin Davis
[not found] ` <f0d712d60612111704x14717093p6e038641fc6e94e6@mail.gmail.com>
2006-12-13 15:22 ` Tobin Davis
2006-12-13 16:36 ` Shaw Terwilliger
2006-12-13 17:11 ` Tobin Davis
2006-12-14 7:01 ` Tobin Davis
2006-12-14 15:10 ` Shaw Terwilliger
2006-12-14 16:51 ` Tobin Davis
2006-12-14 21:24 ` Shaw Terwilliger
2006-12-15 2:28 ` Tobin Davis
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=45748CF5.8040800@sourcegear.com \
--to=sterwill@sourcegear.com \
--cc=alsa-devel@lists.sourceforge.net \
--cc=tdavis@dsl-only.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox