From: bugtrack@alsa-project.org
To: alsa-devel@alsa-project.org
Subject: [ALSA - driver 0000669]: Creative SB Live! 24-bit External (USB) works only at a minimal level.
Date: Sat, 3 Dec 2005 16:51:37 +0100 [thread overview]
Message-ID: <68576dfa04d6dcf828676b24c8850815@bugtrack.alsa-project.org> (raw)
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=669>
======================================================================
Reported By: Henni
Assigned To: Clemens Ladisch
======================================================================
Project: ALSA - driver
Issue ID: 669
Category: USB - usb-audio
Reproducibility: always
Severity: feature
Priority: normal
Status: assigned
Distribution: Gentoo 2004.3
Kernel Version: 2.6.9-cko3
======================================================================
Date Submitted: 11-23-2004 19:23 CET
Last Modified: 12-03-2005 16:51 CET
======================================================================
Summary: Creative SB Live! 24-bit External (USB) works only
at a minimal level.
Description:
The Creative SB Live! 24-bit External is a "card" similar to the Audigy 2
NX (probably its litte brother).
With the snd-usb-audio the ''only'' thing working is the stereo output. I
read that the Audigy 2 NX works far better with the snd-usb-audio.
Probably there is a way to get the SB Live! 24-bit on a similar lvl?
PS: I added some informations about it as an attachment.
======================================================================
----------------------------------------------------------------------
Henni - 05-23-05 12:37
----------------------------------------------------------------------
I retested everything with ALSA Version 1.0.9-rc3 and now the Optical
Digital Out works perfect (I didn't test the Coaxial Out) with mplayer:
Tested with following output formats:
*) Dolby Digital AC3 2.0
*) Dolby Digital AC3 5.1
*) DTS 5.1
*) DTS 6.1
*) PCM
Only thing you have to is to set the AudioOut Device of mplayer to -ao
alsa:device=default (if you try to use -ao alsa without device=default it
tries to open a iec9.. device which doesn't work) and using Audiocodec
hwac3 (for DD) or hwdts (for DTS).
4 Channel and 6 Channel Mode are working perfectly (at the DigitalOut you
only get PCM-Stereo) using the Speaker outputs of the device.
There are no more problems setting the Volume higher than aroung 75% (in
the past it stopped playing and you had to reload the driver). The only
thing you have to do is to unmute it when you change the output at the
device (as an example if you unplug the digital-out and plug in
headphones.)
----------------------------------------------------------------------
rev_jazz - 12-03-05 16:51
----------------------------------------------------------------------
No digital passthrough for Creative Audigy 2 NX
I tried with alsa1.0.9a (on an ubuntu) to wake work the ac3 passthrough
(with an extarnal decoder) usiing the coaxial digital out. It didn't work
fine at all neither using mplayer with -ao alsa:device=default -ac hwac3
nor with xine. mplayer issues in two ways:
1- says :
alsa-init: 1 soundcard found, using: iec958:{CARD 0 AES0 0x02 AES1 0x82
AES2 0x0 0 AES3 0x02}
ALSA lib pcm.c:1959:(snd_pcm_open_conf) Invalid type for PCM iec958:{CARD
0 AES0 0x02 AES1 0x82 AES2 0x00 AES3 0x02} definition (id: iec958, value:
cards.pcm.ie c958)
or
2- sends to extarnal amplifier lots of crack and gap noise
It's to be no configuration way to make the ac3/dts digital out
passthrough work
regards,
jazz
PS: alsa default is set to PCM
Issue History
Date Modified Username Field Change
======================================================================
11-23-04 19:23 Henni New Issue
11-23-04 19:23 Henni File Added: output.txt
11-23-04 19:23 Henni Distribution => Gentoo 2004.3
11-23-04 19:23 Henni Kernel Version => 2.6.9-cko3
11-23-04 19:58 Henni Issue Monitored: Henni
11-23-04 21:09 pzad Note Added: 0002527
11-24-04 00:51 Henni Note Added: 0002540
01-09-05 02:04 kempokaraterulzNote Added: 0003133
03-19-05 02:04 chaosmcgruff Issue Monitored: chaosmcgruff
05-23-05 12:37 Henni Note Added: 0004703
12-03-05 16:51 rev_jazz Note Added: 0006899
======================================================================
-------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc. Do you grep through log files
for problems? Stop! Download the new AJAX search engine that makes
searching your log files as easy as surfing the web. DOWNLOAD SPLUNK!
http://ads.osdn.com/?ad_id=7637&alloc_id=16865&op=click
next reply other threads:[~2005-12-03 15:51 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-12-03 15:51 bugtrack [this message]
-- strict thread matches above, loose matches on Subject: below --
2005-05-23 10:37 [ALSA - driver 0000669]: Creative SB Live! 24-bit External (USB) works only at a minimal level bugtrack
2005-01-09 1:04 bugtrack
2004-11-23 23:51 bugtrack
2004-11-23 20:09 bugtrack
2004-11-23 18:23 bugtrack
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=68576dfa04d6dcf828676b24c8850815@bugtrack.alsa-project.org \
--to=bugtrack@alsa-project.org \
--cc=alsa-devel@alsa-project.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox