[PATCH AUTOSEL 4.9 01/73] ath10k: Do not send probe response template for mesh

[PATCH AUTOSEL 4.9 01/73] ath10k: Do not send probe response template for mesh

[Sasha Levin]

From: Surabhi Vishnoi <svishnoi@codeaurora.org>

[ Upstream commit 97354f2c432788e3163134df6bb144f4b6289d87 ]

Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.

To avoid this failure, skip sending probe response template to
firmware for mesh point.

Tested HW: WCN3990/QCA6174/QCA9984

Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/mac.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/mac.c b/drivers/net/wireless/ath/ath10k/mac.c
index fb632a454fc2..1588fe8110d0 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -1596,6 +1596,10 @@ static int ath10k_mac_setup_prb_tmpl(struct ath10k_vif *arvif)
 	if (arvif->vdev_type != WMI_VDEV_TYPE_AP)
 		return 0;
 
+	 /* For mesh, probe response and beacon share the same template */
+	if (ieee80211_vif_is_mesh(vif))
+		return 0;
+
 	prb = ieee80211_proberesp_get(hw, vif);
 	if (!prb) {
 		ath10k_warn(ar, "failed to get probe resp template from mac80211\n");
-- 
2.20.1


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH AUTOSEL 4.9 54/73] ath10k: fix PCIE device wake up failed

[Sasha Levin]

From: Miaoqing Pan <miaoqing@codeaurora.org>

[ Upstream commit 011d4111c8c602ea829fa4917af1818eb0500a90 ]

Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"

The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake

Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.

But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.

Tested HW: QCA9984

Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath10k/hw.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath10k/hw.c b/drivers/net/wireless/ath/ath10k/hw.c
index 675e75d66db2..14dc6548701c 100644
--- a/drivers/net/wireless/ath/ath10k/hw.c
+++ b/drivers/net/wireless/ath/ath10k/hw.c
@@ -157,7 +157,7 @@ const struct ath10k_hw_values qca6174_values = {
 };
 
 const struct ath10k_hw_values qca99x0_values = {
-	.rtc_state_val_on		= 5,
+	.rtc_state_val_on		= 7,
 	.ce_count			= 12,
 	.msi_assign_ce_max		= 12,
 	.num_target_ce_config_wlan	= 10,
-- 
2.20.1


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k