* Re: ath10k-firmware: QCA6174: hw3.0: Add board file for DragonBoard 820c
2022-04-02 11:09 ath10k-firmware: QCA6174: hw3.0: Add board file for DragonBoard 820c Dmitry Baryshkov
@ 2022-04-02 13:36 ` Dmitry Baryshkov
2022-04-13 9:09 ` Kalle Valo
1 sibling, 0 replies; 3+ messages in thread
From: Dmitry Baryshkov @ 2022-04-02 13:36 UTC (permalink / raw)
To: ath10k
On Sat, 2 Apr 2022 at 14:09, Dmitry Baryshkov
<dmitry.baryshkov@linaro.org> wrote:
> We'd like to ask for inclusion of the board file for the 96boards
> DragonBoard 820c. It is a development board is based on the Qualcomm®
> Snapdragon 820E embedded platform (APQ8096).
> Following the questions from the ath10k wiki page:
>
> * description for what hardware this is
> - It is an APQ8096 based board.
> - It uses qca6174 chip as a WiFi and BT radio
>
> * origin of the board file
> - It comes from the BSP package distributed by Linaro
> (http://releases.linaro.org/96boards/dragonboard820c/qualcomm/firmware/linux-board-support-package-r01700.1.zip)
>
> * ids to be used with the board file
> bus=pci,bmi-chip-id=0,bmi-board-id=1
>
> * md5sum of each new board file to add
>
> $ md5sum *
> 1189e99afcae7b57bf5bd369e9ad1386 bus=pci,bmi-chip-id=0,bmi-board-id=1.bin
> $ sha256sum *
> d6538f04ad351c1f911acee0334245a4b322f709096f2a74ec51684b8080be2a
> bus=pci,bmi-chip-id=0,bmi-board-id=1.bin
In case you wonder, here is the lspci entry:
0000:01:00.0 Network controller [0280]: Qualcomm Atheros QCA6174
802.11ac Wireless Network Adapter [168c:003e] (rev 32)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 97
Region 0: Memory at 0c400000 (64-bit, non-prefetchable) [size=2M]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit-
Address: da001800 Data: 0001
Masking: 000000fe Pending: 00000000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
unlimited, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+
FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Exit Latency L0s <4us, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported,
TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message,
ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported,
EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LTR+ OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkCap2: Supported Link Speeds: 2.5GT/s, Crosslink-
Retimer- 2Retimers- DRS-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB,
EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3-
LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP+ Rollover- Timeout-
AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap-
ECRCGenEn- ECRCChkCap- ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [148 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [168 v1] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [178 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [180 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+
ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=50us PortTPowerOnTime=10us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=65536ns
L1SubCtl2: T_PwrOn=10us
Kernel driver in use: ath10k_pci
--
With best wishes
Dmitry
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: ath10k-firmware: QCA6174: hw3.0: Add board file for DragonBoard 820c
2022-04-02 11:09 ath10k-firmware: QCA6174: hw3.0: Add board file for DragonBoard 820c Dmitry Baryshkov
2022-04-02 13:36 ` Dmitry Baryshkov
@ 2022-04-13 9:09 ` Kalle Valo
1 sibling, 0 replies; 3+ messages in thread
From: Kalle Valo @ 2022-04-13 9:09 UTC (permalink / raw)
To: Dmitry Baryshkov; +Cc: ath10k
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> writes:
> Hi,
>
> We'd like to ask for inclusion of the board file for the 96boards
> DragonBoard 820c. It is a development board is based on the Qualcomm®
> Snapdragon 820E embedded platform (APQ8096).
> Following the questions from the ath10k wiki page:
>
> * description for what hardware this is
> - It is an APQ8096 based board.
> - It uses qca6174 chip as a WiFi and BT radio
>
> * origin of the board file
> - It comes from the BSP package distributed by Linaro
> (http://releases.linaro.org/96boards/dragonboard820c/qualcomm/firmware/linux-board-support-package-r01700.1.zip)
>
> * ids to be used with the board file
> bus=pci,bmi-chip-id=0,bmi-board-id=1
>
> * md5sum of each new board file to add
>
> $ md5sum *
> 1189e99afcae7b57bf5bd369e9ad1386 bus=pci,bmi-chip-id=0,bmi-board-id=1.bin
> $ sha256sum *
> d6538f04ad351c1f911acee0334245a4b322f709096f2a74ec51684b8080be2a
> bus=pci,bmi-chip-id=0,bmi-board-id=1.bin
Thanks, added to QCA6174/hw3.0/board-2.bin:
New:
bus=pci,bmi-chip-id=0,bmi-board-id=1
Changed:
Deleted:
1 board image(s) added, 0 changed, 0 deleted, 89 in total
https://github.com/kvalo/ath10k-firmware/commit/82047838f1ce1f5d010a4ada1509ebad8dcf79c2
--
https://patchwork.kernel.org/project/linux-wireless/list/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 3+ messages in thread