* Compex WLE900N5-23 @ 2015-04-30 2:29 Yeoh Chun-Yeow 2015-04-30 3:02 ` Kalle Valo 0 siblings, 1 reply; 17+ messages in thread From: Yeoh Chun-Yeow @ 2015-04-30 2:29 UTC (permalink / raw) To: ath10k@lists.infradead.org Hi, all I am using the above WiFi card and found out that it can only use the firmware-2.bin_10.1.467.2-1 (10.1), but not 10.2 or 10.3 (firmware crashed) for AP mode. Is that any reason of this? -------- Chun-Yeow _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-04-30 2:29 Compex WLE900N5-23 Yeoh Chun-Yeow @ 2015-04-30 3:02 ` Kalle Valo 2015-04-30 4:27 ` Yeoh Chun-Yeow 0 siblings, 1 reply; 17+ messages in thread From: Kalle Valo @ 2015-04-30 3:02 UTC (permalink / raw) To: Yeoh Chun-Yeow; +Cc: ath10k@lists.infradead.org Yeoh Chun-Yeow <yeohchunyeow@gmail.com> writes: > I am using the above WiFi card and found out that it can only use the > firmware-2.bin_10.1.467.2-1 (10.1), but not 10.2 or 10.3 (firmware > crashed) for AP mode. > > Is that any reason of this? I can't think of any reason from top of my head. Can you send full (complete) kernel logs and information what kernel and ath10k version you are using? -- Kalle Valo _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-04-30 3:02 ` Kalle Valo @ 2015-04-30 4:27 ` Yeoh Chun-Yeow 2015-04-30 5:11 ` Michal Kazior 0 siblings, 1 reply; 17+ messages in thread From: Yeoh Chun-Yeow @ 2015-04-30 4:27 UTC (permalink / raw) To: Kalle Valo; +Cc: ath10k@lists.infradead.org [-- Attachment #1: Type: text/plain, Size: 1486 bytes --] Kernel version: 3.18.11 (OpenWRT based platform latest trunk) [ 12.690000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 12.700000] Backport generated by backports.git backports-20150129-0-gdd4a670 This is the configuration: driver=nl80211 logger_syslog=127 logger_syslog_level=2 logger_stdout=127 logger_stdout_level=2 hw_mode=a channel=36 ieee80211n=1 ht_capab=[HT40+][LDPC][SHORT-GI-20][SHORT-GI-40][TX-STBC][RX-STBC1][MAX-AMSDU-7935][DSSS_CCK-40] vht_oper_chwidth=1 vht_oper_centr_freq_seg0_idx=42 ieee80211ac=1 vht_capab=[RXLDPC][SHORT-GI-80][TX-STBC-2BY1][RX-ANTENNA-PATTERN][TX-ANTENNA-PATTERN][RX-STBC1][MAX-MPDU-11454][MAX-A-MPDU-LEN-EXP7] interface=wlan0 ctrl_interface=/var/run/hostapd disassoc_low_ack=1 preamble=1 wmm_enabled=1 ignore_broadcast_ssid=0 uapsd_advertisement_enabled=1 auth_algs=1 wpa=0 ssid=ath10k bridge=br-lan bssid=04:f0:21:0c:a5:44 Attached is the kernel log. Let me know what can I do. ---- Chun-Yeow On Thu, Apr 30, 2015 at 11:02 AM, Kalle Valo <kvalo@qca.qualcomm.com> wrote: > Yeoh Chun-Yeow <yeohchunyeow@gmail.com> writes: > >> I am using the above WiFi card and found out that it can only use the >> firmware-2.bin_10.1.467.2-1 (10.1), but not 10.2 or 10.3 (firmware >> crashed) for AP mode. >> >> Is that any reason of this? > > I can't think of any reason from top of my head. Can you send full > (complete) kernel logs and information what kernel and ath10k version > you are using? > > -- > Kalle Valo [-- Attachment #2: kernel.log --] [-- Type: text/x-log, Size: 24113 bytes --] [ 0.000000] Linux version 3.18.11 (chunyeow@nga) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44439) ) #6 Mon Apr 27 18:47:21 MYT 2015 [ 0.000000] MyLoader: sysp=a1813e82, boardp=e56269b5, parts=5b9abbc8 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001974c (MIPS 74Kc) [ 0.000000] SoC: Atheros AR9344 rev 2 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 8039dfd0, node_mem_map 81000000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: board=WPJ344 console=ttyS0,115200 mtdparts=spi0.0:192k(u-boot)ro,16128k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 125496K/131072K available (2642K kernel code, 210K rwdata, 632K rodata, 280K init, 231K bss, 5576K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz [ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.220000] NET: Registered protocol family 16 [ 0.220000] MIPS: machine is Compex WPJ344 [ 0.230000] registering PCI controller with io_map_base unset [ 0.240000] ar71xx: using random MAC address for eth0 [ 0.680000] PCI host bridge to bus 0000:00 [ 0.690000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.690000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.700000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.700000] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000 [ 0.700000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.700000] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.700000] pci 0000:00:00.0: supports D1 D2 [ 0.700000] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 0.700000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.700000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 0.710000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [ 0.710000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.720000] Switched to clocksource MIPS [ 0.740000] NET: Registered protocol family 2 [ 0.750000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.750000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.760000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.770000] TCP: reno registered [ 0.770000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.770000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.780000] NET: Registered protocol family 1 [ 0.790000] PCI: CLS 0 bytes, default 32 [ 0.790000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.800000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.810000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.820000] msgmni has been set to 245 [ 0.820000] io scheduler noop registered [ 0.820000] io scheduler deadline registered (default) [ 0.830000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.830000] console [ttyS0] disabled [ 0.860000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 2500000) is a 16550A [ 0.870000] console [ttyS0] enabled [ 0.870000] bootconsole [early0] disabled [ 0.880000] m25p80 spi0.0: found mx25l6405d, expected m25p80 [ 0.890000] m25p80 spi0.0: mx25l6405d (8192 Kbytes) [ 0.890000] mtd: spi0.0: partitioning exceeds flash size, truncating [ 0.900000] mtd: spi0.0: partitioning exceeds flash size, truncating [ 0.910000] mtd: spi0.0: skipping zero sized partition [ 0.910000] 2 cmdlinepart partitions found on MTD device spi0.0 [ 0.920000] Creating 2 MTD partitions on "spi0.0": [ 0.920000] 0x000000000000-0x000000030000 : "u-boot" [ 0.930000] 0x000000030000-0x000000800000 : "firmware" [ 0.950000] 2 uimage-fw partitions found on MTD device firmware [ 0.960000] 0x000000030000-0x000000160000 : "kernel" [ 0.960000] 0x000000160000-0x000000800000 : "rootfs" [ 0.970000] mtd: device 3 (rootfs) set to be root filesystem [ 0.970000] 1 squashfs-split partitions found on MTD device rootfs [ 0.980000] 0x0000006c0000-0x000000800000 : "rootfs_data" [ 1.010000] libphy: ag71xx_mdio: probed [ 1.020000] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0 [ 1.080000] libphy: ag71xx_mdio: probed [ 1.680000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316] [ 1.690000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII [ 2.280000] ag71xx-mdio.1: Found an AR934X built-in switch [ 2.320000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII [ 2.330000] TCP: cubic registered [ 2.330000] NET: Registered protocol family 17 [ 2.330000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 2.350000] Bridge firewalling registered [ 2.350000] 8021q: 802.1Q VLAN Support v1.8 [ 2.360000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 2.370000] Freeing unused kernel memory: 280K (803ca000 - 80410000) [ 3.340000] init: failed to symlink /tmp -> /var [ 3.350000] init: Console is alive [ 3.350000] init: - watchdog - [ 5.290000] usbcore: registered new interface driver usbfs [ 5.290000] usbcore: registered new interface driver hub [ 5.300000] usbcore: registered new device driver usb [ 5.310000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.320000] ehci-platform: EHCI generic platform driver [ 5.320000] ehci-platform ehci-platform: EHCI Host Controller [ 5.330000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 5.340000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 5.360000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 5.360000] hub 1-0:1.0: USB hub found [ 5.370000] hub 1-0:1.0: 1 port detected [ 5.370000] ehci-pci: EHCI PCI platform driver [ 5.380000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.390000] ohci-platform: OHCI generic platform driver [ 5.390000] uhci_hcd: USB Universal Host Controller Interface driver [ 5.440000] init: - preinit - [ 6.060000] random: procd urandom read with 9 bits of entropy available [ 7.800000] eth0: link up (1000Mbps/Full duplex) [ 9.370000] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 1 of xref (0 dead, 0 orphan) found. [ 9.390000] mount_root: switching to jffs2 overlay [ 9.430000] eth0: link down [ 9.440000] procd: - early - [ 9.450000] procd: - watchdog - [ 10.240000] procd: - ubus - [ 11.260000] procd: - init - [ 12.650000] NET: Registered protocol family 10 [ 12.660000] tun: Universal TUN/TAP device driver, 1.6 [ 12.670000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 12.680000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 12.690000] Loading modules backported from Linux version master-2015-03-09-0-g141f155 [ 12.700000] Backport generated by backports.git backports-20150129-0-gdd4a670 [ 12.740000] cfg80211: Calling CRDA to update world regulatory domain [ 12.800000] cfg80211: World regulatory domain updated: [ 12.800000] cfg80211: DFS Master region: unset [ 12.800000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 12.810000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 12.820000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 12.830000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 12.840000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 12.850000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 12.860000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 12.870000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 12.870000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 12.930000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 12.940000] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0 [ 13.160000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2 [ 13.170000] ath10k_pci 0000:00:00.0: Falling back to user helper [ 13.260000] firmware ath10k!cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed [ 14.610000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 14.620000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 14.630000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 14.640000] ath10k_pci 0000:00:00.0: no channel configured; ignoring frame(s)! [ 14.740000] ath: EEPROM regdomain: 0x0 [ 14.740000] ath: EEPROM indicates default country code should be used [ 14.740000] ath: doing EEPROM country->regdmn map search [ 14.740000] ath: country maps to regdmn code: 0x3a [ 14.740000] ath: Country alpha2 being used: US [ 14.740000] ath: Regpair used: 0x3a [ 14.740000] cfg80211: Calling CRDA for country: US [ 14.750000] arp_tables: (C) 2002 David S. Miller [ 14.770000] cfg80211: Regulatory domain changed to country: US [ 14.770000] cfg80211: DFS Master region: FCC [ 14.780000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 14.790000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A) [ 14.790000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 1700 mBm), (N/A) [ 14.800000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2300 mBm), (0 s) [ 14.810000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A) [ 14.820000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A) [ 14.870000] usbcore: registered new interface driver cdc_wdm [ 14.920000] Ebtables v2.0 registered [ 14.920000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 14.930000] usbcore: registered new interface driver ipheth [ 14.940000] usbcore: registered new interface driver kaweth [ 14.960000] nf_conntrack version 0.5.0 (1965 buckets, 7860 max) [ 15.020000] Netfilter messages via NETLINK v0.30. [ 15.030000] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 15.040000] usbcore: registered new interface driver pegasus [ 15.130000] xt_time: kernel timezone is -0000 [ 15.140000] usbcore: registered new interface driver asix [ 15.160000] usbcore: registered new interface driver ath9k_htc [ 15.170000] usbcore: registered new interface driver cdc_ether [ 15.180000] usbcore: registered new interface driver cdc_ncm [ 15.190000] usbcore: registered new interface driver dm9601 [ 15.200000] usbcore: registered new interface driver kalmia [ 15.210000] usbcore: registered new interface driver MOSCHIP usb-ethernet driver [ 15.230000] ctnetlink v0.93: registering with nfnetlink. [ 15.240000] PPP generic driver version 2.4.2 [ 15.250000] NET: Registered protocol family 24 [ 15.250000] usbcore: registered new interface driver qmi_wwan [ 15.270000] usbcore: registered new interface driver rndis_host [ 15.290000] usbcore: registered new interface driver rt2800usb [ 15.310000] usbcore: registered new interface driver sierra_net [ 15.320000] usbcore: registered new interface driver smsc95xx [ 15.350000] ath: phy1: eeprom contains invalid mac address: c9:c0:93:30:32:46 [ 15.350000] ath: phy1: random mac address will be used: d2:29:8a:f2:02:29 [ 15.360000] ath: EEPROM regdomain: 0xabd3 [ 15.360000] ath: EEPROM indicates we should expect a country code [ 15.360000] ath: invalid regulatory domain/country code 0xabd3 [ 15.360000] ath: Invalid EEPROM contents [ 15.370000] ath9k ar934x_wmac: failed to initialize device [ 15.370000] ath9k: probe of ar934x_wmac failed with error -22 [ 15.380000] usbcore: registered new interface driver cdc_mbim [ 15.400000] usbcore: registered new interface driver rtl8192cu [ 22.640000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 22.660000] device eth0.1 entered promiscuous mode [ 22.660000] device eth0 entered promiscuous mode [ 22.680000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 22.740000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready [ 24.290000] eth0: link up (1000Mbps/Full duplex) [ 24.290000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 24.300000] br-lan: port 1(eth0.1) entered forwarding state [ 24.310000] br-lan: port 1(eth0.1) entered forwarding state [ 24.310000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready [ 24.340000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 26.290000] Atheros AR8216/AR8236/AR8316 ag71xx-mdio.0:00: Port 3 is up [ 26.310000] br-lan: port 1(eth0.1) entered forwarding state [ 73.680000] random: nonblocking pool is initialized [ 334.890000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 70fe3043-d0a5-4deb-b28b-9ffe2a1a8ddf) [ 334.900000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 334.910000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 334.930000] ath10k_warn: 12 callbacks suppressed [ 334.940000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16 [ 334.940000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16 [ 334.950000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 335.060000] ieee80211 phy0: Hardware restart was requested [ 335.060000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143 [ 335.070000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143 [ 335.080000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 [ 335.290000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 335.300000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 335.410000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 335.420000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 335.530000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 336.500000] br-lan: port 2(wlan0) entered forwarding state [ 337.720000] ath10k_pci 0000:00:00.0: device successfully recovered [ 338.100000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid ceade50a-ec8f-49b7-8ff5-f0d05f8ea297) [ 338.110000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 338.120000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 338.140000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 338.250000] ieee80211 phy0: Hardware restart was requested [ 340.850000] ath10k_pci 0000:00:00.0: device successfully recovered [ 341.230000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 392f9a20-520b-4aa0-b4d7-f0869bb861a2) [ 341.240000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 341.250000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 341.270000] ath10k_warn: 12 callbacks suppressed [ 341.280000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16 [ 341.280000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16 [ 341.290000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 341.400000] ieee80211 phy0: Hardware restart was requested [ 341.400000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143 [ 341.410000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143 [ 341.420000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 [ 341.630000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 341.640000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 341.750000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 341.760000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 341.870000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 344.050000] ath10k_pci 0000:00:00.0: device successfully recovered [ 344.430000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 461e83d2-a379-4dc4-a9f7-7490df8bec1b) [ 344.440000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 344.450000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 344.470000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 344.580000] ieee80211 phy0: Hardware restart was requested [ 347.180000] ath10k_pci 0000:00:00.0: device successfully recovered [ 347.560000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 8b4c4ad1-e03a-44cf-a92a-048e349915c6) [ 347.570000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 347.580000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 347.600000] ath10k_warn: 12 callbacks suppressed [ 347.610000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16 [ 347.610000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16 [ 347.620000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 347.730000] ieee80211 phy0: Hardware restart was requested [ 347.730000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143 [ 347.740000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143 [ 347.750000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 [ 347.960000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 347.970000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 348.080000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 348.090000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 348.200000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 350.380000] ath10k_pci 0000:00:00.0: device successfully recovered [ 350.760000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 1667c239-5d9a-4e77-b12f-d84413c1711a) [ 350.770000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 350.790000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 350.810000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 350.920000] ieee80211 phy0: Hardware restart was requested [ 353.770000] ath10k_pci 0000:00:00.0: device successfully recovered [ 354.150000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 2673b3ca-7264-4ef3-8c4c-b9f585484310) [ 354.160000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 354.180000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 354.200000] ath10k_warn: 12 callbacks suppressed [ 354.200000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16 [ 354.210000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16 [ 354.220000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 354.320000] ieee80211 phy0: Hardware restart was requested [ 354.320000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143 [ 354.330000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143 [ 354.340000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 [ 354.550000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 354.560000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 354.670000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 354.680000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 354.790000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 356.970000] ath10k_pci 0000:00:00.0: device successfully recovered [ 357.350000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 820a0d16-3226-45a5-ba6b-1f7801a313d6) [ 357.360000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 357.370000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 357.390000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 357.500000] ieee80211 phy0: Hardware restart was requested [ 360.100000] ath10k_pci 0000:00:00.0: device successfully recovered [ 360.480000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 0f22de64-dca5-4bc9-aac4-113a4adf1bd0) [ 360.490000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 360.500000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 360.520000] ath10k_warn: 12 callbacks suppressed [ 360.530000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16 [ 360.530000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16 [ 360.540000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 360.650000] ieee80211 phy0: Hardware restart was requested [ 360.650000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143 [ 360.660000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143 [ 360.670000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 [ 360.880000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 360.890000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 361.000000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 361.010000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 361.120000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [-- Attachment #3: Type: text/plain, Size: 146 bytes --] _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-04-30 4:27 ` Yeoh Chun-Yeow @ 2015-04-30 5:11 ` Michal Kazior 2015-04-30 6:46 ` Yeoh Chun-Yeow 0 siblings, 1 reply; 17+ messages in thread From: Michal Kazior @ 2015-04-30 5:11 UTC (permalink / raw) To: Yeoh Chun-Yeow; +Cc: Kalle Valo, ath10k@lists.infradead.org On 30 April 2015 at 06:27, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: > Kernel version: 3.18.11 (OpenWRT based platform latest trunk) > > [ 12.690000] Loading modules backported from Linux version > master-2015-03-09-0-g141f155 > [ 12.700000] Backport generated by backports.git backports-20150129-0-gdd4a670 [...] > Attached is the kernel log. Let me know what can I do. > > ---- > Chun-Yeow Hmm.. So it looks like the device worked for a few minutes first before crashing, right? Then it crashed, restarted and crashed immediately after that after which everything went bad bad. The -16 diag errors suggests that the device CE goes down. The logs are a bit lacking (debug logs would be much better) and I'm not really sure whether your device gets a cold reset or only a warm reset.The latter could explain why it can't resume regular operation. Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-04-30 5:11 ` Michal Kazior @ 2015-04-30 6:46 ` Yeoh Chun-Yeow 2015-04-30 7:05 ` Michal Kazior 0 siblings, 1 reply; 17+ messages in thread From: Yeoh Chun-Yeow @ 2015-04-30 6:46 UTC (permalink / raw) To: Michal Kazior; +Cc: Kalle Valo, ath10k@lists.infradead.org [-- Attachment #1: Type: text/plain, Size: 1112 bytes --] Hi, Michal Attached is the partial log. Hopefully it is useful for you. Thanks ---- Chun-Yeow On Thu, Apr 30, 2015 at 1:11 PM, Michal Kazior <michal.kazior@tieto.com> wrote: > On 30 April 2015 at 06:27, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >> Kernel version: 3.18.11 (OpenWRT based platform latest trunk) >> >> [ 12.690000] Loading modules backported from Linux version >> master-2015-03-09-0-g141f155 >> [ 12.700000] Backport generated by backports.git backports-20150129-0-gdd4a670 > [...] >> Attached is the kernel log. Let me know what can I do. >> >> ---- >> Chun-Yeow > > Hmm.. So it looks like the device worked for a few minutes first > before crashing, right? Then it crashed, restarted and crashed > immediately after that after which everything went bad bad. > > The -16 diag errors suggests that the device CE goes down. The logs > are a bit lacking (debug logs would be much better) and I'm not really > sure whether your device gets a cold reset or only a warm reset.The > latter could explain why it can't resume regular operation. > > > Michał [-- Attachment #2: kernel.log --] [-- Type: text/x-log, Size: 91632 bytes --] [ 47.990000] ath10k_pci 0000:00:00.0: mac channel [4/13] freq 5260 maxpower 46 regpower 46 antenna 0 mode 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac channel [5/13] freq 5280 maxpower 46 regpower 46 antenna 0 mode 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac channel [6/13] freq 5300 maxpower 46 regpower 46 antenna 0 mode 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac channel [7/13] freq 5320 maxpower 46 regpower 46 antenna 0 mode 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac channel [8/13] freq 5745 maxpower 60 regpower 60 antenna 0 mode 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac channel [9/13] freq 5765 maxpower 60 regpower 60 antenna 0 mode 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac channel [10/13] freq 5785 maxpower 60 regpower 60 antenna 0 mode 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac channel [11/13] freq 5805 maxpower 60 regpower 60 antenna 0 mode 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac channel [12/13] freq 5825 maxpower 60 regpower 60 antenna 0 mode 0 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665a100 len 328 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 40 01 00 09 00 00 02 90 00 00 0d 00 00 00 ..@............. [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 3c 14 00 00 3c 14 00 00 00 00 00 00 40 19 00 00 <...<.......@... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 22 22 00 00 00 00 00 50 14 00 00 50 14 00 00 ."".....P...P... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 40 19 00 00 00 22 22 00 00 00 00 00 ....@....""..... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 64 14 00 00 64 14 00 00 00 00 00 00 40 19 00 00 d...d.......@... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 22 22 00 00 00 00 00 78 14 00 00 78 14 00 00 ."".....x...x... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: 00 00 00 00 40 19 00 00 00 22 22 00 00 00 00 00 ....@....""..... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000070: 8c 14 00 00 8c 14 00 00 00 00 00 00 40 1d 00 00 ............@... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000080: 00 2e 2e 00 00 00 00 00 a0 14 00 00 a0 14 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000090: 00 00 00 00 40 1d 00 00 00 2e 2e 00 00 00 00 00 ....@........... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 000000a0: b4 14 00 00 b4 14 00 00 00 00 00 00 40 1d 00 00 ............@... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 000000b0: 00 2e 2e 00 00 00 00 00 c8 14 00 00 c8 14 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 000000c0: 00 00 00 00 00 1d 00 00 00 2e 2e 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 000000d0: 71 16 00 00 71 16 00 00 00 00 00 00 40 19 00 00 q...q.......@... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 000000e0: 00 3c 3c 00 00 00 00 00 85 16 00 00 85 16 00 00 .<<............. [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 000000f0: 00 00 00 00 40 19 00 00 00 3c 3c 00 00 00 00 00 ....@....<<..... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000100: 99 16 00 00 99 16 00 00 00 00 00 00 40 19 00 00 ............@... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000110: 00 3c 3c 00 00 00 00 00 ad 16 00 00 ad 16 00 00 .<<............. [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000120: 00 00 00 00 40 19 00 00 00 3c 3c 00 00 00 00 00 ....@....<<..... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000130: c1 16 00 00 c1 16 00 00 00 00 00 00 00 19 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000140: 00 3c 3c 00 00 00 00 00 .<<..... [ 47.990000] ath10k_pci 0000:00:00.0: wmi pdev regdomain rd 3a rd2g 3a rd5g 3a ctl2g 10 ctl5g 10 dfs_region 1 [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc540 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 0a 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665a360 len 36 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 1c 00 00 0a 04 00 04 90 00 00 3a 00 00 00 ............:... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 3a 00 00 00 3a 00 00 00 10 00 00 00 10 00 00 00 :...:........... [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 01 00 00 00 .... [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc6c0 [ 47.990000] ath10k_pci 0000:00:00.0: mac create vdev 0 map ffff [ 47.990000] ath10k_pci 0000:00:00.0: mac vdev create 0 (add interface) type 1 subtype 0 bcnmode single-buf [ 47.990000] ath10k_pci 0000:00:00.0: WMI vdev create: id 0 type 1 subtype 0 macaddr 04:f0:21:0c:a5:44 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665ada0 len 32 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 18 00 00 0b 00 00 10 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 01 00 00 00 00 00 00 00 04 f0 21 0c a5 44 00 00 ..........!..D.. [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc6c0 [ 47.990000] ath10k_pci 0000:00:00.0: vdev param 0 not supported by firmware [ 47.990000] ath10k_pci 0000:00:00.0: wmi peer create vdev_id 0 peer_addr 04:f0:21:0c:a5:44 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 20 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 01 00 0c 00 00 0b 00 00 03 00 c3 00 04 f0 21 0c ..............!. [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000010: a5 44 00 00 .D.. [ 47.990000] ath10k_pci 0000:00:00.0: pci hif send complete check [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 1 skb 865dc3c0 [ 47.990000] ath10k_pci 0000:00:00.0: htc rx completion ep 1 skb 87365180 [ 47.990000] ath10k_pci 0000:00:00.0: htt rx, msg_type: 0x3 [ 47.990000] ath10k_pci 0000:00:00.0: htt peer map vdev 0 peer 04:f0:21:0c:a5:44 id 195 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 20 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 01 00 0c 00 00 0c 00 00 03 00 d3 00 04 f0 21 0c ..............!. [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000010: a5 44 00 00 .D.. [ 47.990000] ath10k_pci 0000:00:00.0: pci hif send complete check [ 47.990000] ath10k_pci 0000:00:00.0: htc rx completion ep 1 skb 873653c0 [ 47.990000] ath10k_pci 0000:00:00.0: htt rx, msg_type: 0x3 [ 47.990000] ath10k_pci 0000:00:00.0: htt peer map vdev 0 peer 04:f0:21:0c:a5:44 id 211 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 0d 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665aec0 len 24 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 10 00 00 0c 00 00 1c 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 04 f0 21 0c a5 44 00 00 ..!..D.. [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc6c0 [ 47.990000] ath10k_pci 0000:00:00.0: wmi pdev set param 13 value 50 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665cae0 len 20 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 0c 00 00 0d 04 00 06 90 00 00 0d 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 32 00 00 00 2... [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc900 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 0e 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 38 value 3747 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665cc00 len 24 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 10 00 00 0e 00 00 19 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 26 00 00 00 a3 0e 00 00 &....... [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc6c0 [ 47.990000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 39 value 3895 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665d620 len 24 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 10 00 00 0f 00 00 19 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 27 00 00 00 37 0f 00 00 '...7... [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc9c0 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 0f 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 40 value 3900 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665d740 len 24 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 10 00 00 10 00 00 19 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 28 00 00 00 3c 0f 00 00 (...<... [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc6c0 [ 47.990000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 1 value -1 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665e160 len 24 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 10 00 00 11 00 00 19 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 01 00 00 00 ff ff ff ff ........ [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dca80 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 10 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 2 value -1 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665e280 len 24 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 10 00 00 12 00 00 19 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 02 00 00 00 ff ff ff ff ........ [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc6c0 [ 47.990000] ath10k_pci 0000:00:00.0: mac txpower 0 [ 47.990000] ath10k_pci 0000:00:00.0: wmi pdev set param 3 value 0 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665eca0 len 20 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 0c 00 86 13 92 00 06 90 00 00 03 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 00 00 00 00 .... [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dc6c0 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 11 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: wmi pdev set param 4 value 0 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665edc0 len 20 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 0c 00 00 14 00 00 06 90 00 00 04 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 00 00 00 00 .... [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dcb40 [ 47.990000] ath10k_pci 0000:00:00.0: mac monitor recalc started? 0 should? 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac vdev 0 cts_prot 0 [ 47.990000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 43 value 0 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x0665f7e0 len 24 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 10 00 00 15 04 00 19 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 2b 00 00 00 00 00 00 00 +....... [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dcb40 [ 47.990000] ath10k_pci 0000:00:00.0: mac vdev 0 slot_time 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 12 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 7 value 1 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e40940 len 24 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 10 00 00 16 00 00 19 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 07 00 00 00 01 00 00 00 ........ [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dcc00 [ 47.990000] ath10k_pci 0000:00:00.0: mac vdev 0 preamble 1n [ 47.990000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 8 value 1 [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e40a60 len 24 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 10 00 00 17 00 00 19 90 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 08 00 00 00 01 00 00 00 ........ [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dcc00 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 13 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: wmi pdev set wmm params [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e41480 len 108 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 64 00 00 18 00 00 09 90 00 00 00 00 00 00 ..d............. [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 03 00 00 00 07 00 00 00 02 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: e0 05 00 00 00 00 00 00 00 00 00 00 ............ [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dccc0 [ 47.990000] ath10k_pci 0000:00:00.0: wmi pdev set wmm params [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e41600 len 108 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 64 00 00 19 00 00 09 90 00 00 00 00 00 00 ..d............. [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 0f 00 00 00 02 00 00 00 c0 0b 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 03 00 00 00 07 00 00 00 02 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: e0 05 00 00 00 00 00 00 00 00 00 00 ............ [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dcd80 [ 47.990000] ath10k_pci 0000:00:00.0: wmi pdev set wmm params [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 14 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e41780 len 108 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 64 00 00 1a 00 00 09 90 00 00 0f 00 00 00 ..d............. [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: ff 03 00 00 03 00 00 00 00 00 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 0f 00 00 00 02 00 00 00 c0 0b 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 03 00 00 00 07 00 00 00 02 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: e0 05 00 00 00 00 00 00 00 00 00 00 ............ [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dccc0 [ 47.990000] ath10k_pci 0000:00:00.0: wmi pdev set wmm params [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 47.990000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 47.990000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e42200 len 108 n_items 1 [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 64 00 00 1b 00 00 09 90 00 00 0f 00 00 00 ..d............. [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: ff 03 00 00 03 00 00 00 00 00 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 0f 00 00 00 ff 03 00 00 07 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 0f 00 00 00 02 00 00 00 c0 0b 00 00 00 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 03 00 00 00 07 00 00 00 02 00 00 00 ................ [ 47.990000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: e0 05 00 00 00 00 00 00 00 00 00 00 ............ [ 47.990000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865dce40 [ 47.990000] ath10k_pci 0000:00:00.0: mac config channel 5180MHz flags 0x20 radar 0 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 47.990000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 15 00 00 01 04 00 01 02 02 b4 06 ................ [ 47.990000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 47.990000] ath10k_pci 0000:00:00.0: mac config channel to 5180MHz (cf1 5180MHz cf2 0MHz width 20 (noht)) [ 47.990000] ath10k_pci 0000:00:00.0: mac monitor recalc started? 0 should? 0 [ 47.990000] ath10k_pci 0000:00:00.0: mac monitor recalc started? 0 should? 0 [ 48.000000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 48.000000] ath10k_pci 0000:00:00.0: mac monitor recalc started? 0 should? 0 [ 48.010000] device wlan0 entered promiscuous mode [ 48.010000] ath10k_pci 0000:00:00.0: mac monitor recalc started? 0 should? 1 [ 48.010000] ath10k_pci 0000:00:00.0: WMI vdev create: id 1 type 4 subtype 0 macaddr 04:f0:21:0c:a5:44 [ 48.010000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 48.010000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e42c80 len 32 n_items 1 [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 18 00 00 1c 00 00 10 90 00 00 01 00 00 00 ................ [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 04 00 00 00 00 00 00 00 04 f0 21 0c a5 44 00 00 ..........!..D.. [ 48.010000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 87365180 [ 48.010000] ath10k_pci 0000:00:00.0: mac monitor vdev 1 created [ 48.010000] ath10k_pci 0000:00:00.0: wmi vdev start id 0x1 flags: 0x0, freq 5180, mode 0, ch_flags: 0x0, max_power: 34 [ 48.010000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 48.010000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 48.010000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e42da0 len 140 n_items 1 [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 84 00 00 1d 00 00 12 90 00 00 3c 14 00 00 ............<... [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 3c 14 00 00 00 00 00 00 00 00 00 00 00 22 22 00 <............"". [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................ [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 48.010000] ath10k_pci 0000:00:00.0: pci tx data: 00000080: 00 00 00 00 00 00 00 00 00 00 00 00 ............ [ 48.010000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 87365180 [ 48.010000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 48.010000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 16 00 00 01 04 00 01 02 02 b4 06 ................ [ 48.010000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 48.010000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 28 [ 48.010000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 01 00 14 00 00 17 00 00 0f 00 00 00 3c 14 00 00 ............<... [ 48.010000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 3c 14 00 00 00 00 00 00 00 00 00 00 <........... [ 48.010000] ath10k_pci 0000:00:00.0: pci hif send complete check [ 48.010000] ath10k_pci 0000:00:00.0: htc rx completion ep 1 skb 87813a80 [ 48.010000] ath10k_pci 0000:00:00.0: htt rx, msg_type: 0xF [ 48.020000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 28 [ 48.020000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 14 00 00 18 00 00 04 90 00 00 01 00 00 00 ................ [ 48.020000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 ............ [ 48.020000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e300 [ 48.020000] ath10k_pci 0000:00:00.0: WMI_VDEV_START_RESP_EVENTID [ 48.020000] ath10k_pci 0000:00:00.0: wmi mgmt vdev up id 0x1 assoc id 0 bssid 04:f0:21:0c:a5:44 [ 48.020000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 48.020000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e44a40 len 28 n_items 1 [ 48.020000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 14 00 00 1e 00 00 14 90 00 00 01 00 00 00 ................ [ 48.020000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 00 00 00 00 04 f0 21 0c a5 44 00 00 ......!..D.. [ 48.020000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 87365540 [ 48.020000] ath10k_pci 0000:00:00.0: mac monitor vdev 1 started [ 48.020000] ath10k_pci 0000:00:00.0: mac monitor started [ 48.030000] ath10k_pci 0000:00:00.0: wmi 10x start scan [ 48.030000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 48.030000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 48.030000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e44b60 len 164 n_items 1 [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 9c 00 00 1f 00 00 00 90 00 00 00 a0 00 00 ................ [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 01 a0 00 00 00 00 00 00 01 00 00 00 1f 00 00 00 ................ [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 32 00 00 00 96 00 00 00 32 00 00 00 f4 01 00 00 2.......2....... [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 20 4e 00 00 ............ N.. [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 05 00 00 00 1d 00 00 00 01 00 00 00 02 00 00 00 ................ [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 3c 14 00 00 50 14 00 00 03 00 00 00 01 00 00 00 <...P........... [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: ff ff ff ff ff ff 00 00 04 00 00 00 34 00 00 00 ............4... [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000070: 01 08 0c 12 18 24 30 48 60 6c 2d 1a e3 19 1b ff .....$0H`l-..... [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000080: ff ff 00 00 00 00 00 00 00 00 00 01 00 00 00 00 ................ [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 00000090: 00 00 00 00 00 00 bf 0c b2 01 80 33 ea ff 00 00 ...........3.... [ 48.030000] ath10k_pci 0000:00:00.0: pci tx data: 000000a0: ea ff 00 00 .... [ 48.030000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 87365e40 [ 48.030000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 44 [ 48.030000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 02 24 00 08 19 00 00 00 90 00 00 01 00 00 00 ..$............. [ 48.030000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 03 00 00 00 3c 14 00 00 01 a0 00 00 00 a0 00 00 ....<........... [ 48.030000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 01 04 00 00 02 01 00 00 ............ [ 48.030000] ath10k_pci 0000:00:00.0: htc ep 2 got 1 credits (total 1) [ 48.030000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e3c0 [ 48.030000] ath10k_pci 0000:00:00.0: scan event started type 1 reason 3 freq 5180 req_id 40961 scan_id 40960 vdev_id 0 state starting (1) [ 48.030000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 48.030000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 1a 00 00 00 90 00 00 04 00 00 00 ................ [ 48.030000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 03 00 00 00 3c 14 00 00 01 a0 00 00 00 a0 00 00 ....<........... [ 48.030000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 .... [ 48.030000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e480 [ 48.030000] ath10k_pci 0000:00:00.0: scan event bss channel type 4 reason 3 freq 5180 req_id 40961 scan_id 40960 vdev_id 0 state running (2) [ 48.030000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 48.030000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 1b 00 00 0c 90 00 00 00 00 00 00 ................ [ 48.030000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 3c 14 00 00 01 00 00 00 d3 ff ff ff bf b5 10 00 <............... [ 48.030000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 68 63 44 00 hcD. [ 48.030000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e540 [ 48.030000] ath10k_pci 0000:00:00.0: chan info err_code 0 freq 5180 cmd_flags 1 noise_floor -45 rx_clear_count 1095103 cycle_count 4481896 [ 48.960000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 160 [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 02 98 00 08 1c 00 00 02 80 00 00 00 00 00 00 ................ [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000010: bb d4 00 00 2f 4c fc 17 03 00 00 00 1e 00 00 00 ..../L.......... [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 60 04 00 00 60 04 00 00 00 00 00 00 bb d4 00 00 `...`........... [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000030: 2f 4c fc 17 12 00 00 00 1e 00 00 00 60 04 00 00 /L..........`... [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000040: 60 04 00 00 00 00 00 00 bb d4 00 00 2f 4c fc 17 `.........../L.. [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000050: 45 00 00 00 1e 00 00 00 60 04 00 00 60 04 00 00 E.......`...`... [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000060: 00 00 00 00 bb d4 00 00 2f 4c fc 17 67 00 00 00 ......../L..g... [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000070: 1e 00 00 00 60 04 00 00 60 04 00 00 00 00 00 00 ....`...`....... [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000080: c0 d4 00 00 10 0c fc 0b 8a 29 10 01 03 00 00 00 .........)...... [ 48.960000] ath10k_pci 0000:00:00.0: pci rx: 00000090: c0 d4 00 00 13 0c fc 03 01 04 00 00 02 01 00 00 ................ [ 48.960000] ath10k_pci 0000:00:00.0: htc ep 2 got 1 credits (total 2) [ 48.960000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e600 [ 48.960000] ath10k_pci 0000:00:00.0: wmi event debug mesg len 140 [ 49.010000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 49.010000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 1d 00 00 00 90 00 00 08 00 00 00 ................ [ 49.010000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 03 00 00 00 3c 14 00 00 01 a0 00 00 00 a0 00 00 ....<........... [ 49.010000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 .... [ 49.010000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e6c0 [ 49.010000] ath10k_pci 0000:00:00.0: scan event foreign channel type 8 reason 3 freq 5180 req_id 40961 scan_id 40960 vdev_id 0 state running (2) [ 49.010000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 49.010000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 1e 00 00 0c 90 00 00 00 00 00 00 ................ [ 49.010000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 3c 14 00 00 00 00 00 00 00 00 00 00 bf b5 10 00 <............... [ 49.010000] ath10k_pci 0000:00:00.0: pci rx: 00000020: b0 bd 71 05 ..q. [ 49.010000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e780 [ 49.010000] ath10k_pci 0000:00:00.0: chan info err_code 0 freq 5180 cmd_flags 0 noise_floor 0 rx_clear_count 1095103 cycle_count 91340208 [ 49.160000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 49.160000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 1f 00 00 00 90 00 00 04 00 00 00 ................ [ 49.160000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 03 00 00 00 3c 14 00 00 01 a0 00 00 00 a0 00 00 ....<........... [ 49.160000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 .... [ 49.160000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e840 [ 49.160000] ath10k_pci 0000:00:00.0: scan event bss channel type 4 reason 3 freq 5180 req_id 40961 scan_id 40960 vdev_id 0 state running (2) [ 49.160000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 49.160000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 20 00 00 0c 90 00 00 00 00 00 00 ..... .......... [ 49.160000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 3c 14 00 00 01 00 00 00 97 ff ff ff bf b5 10 00 <............... [ 49.160000] ath10k_pci 0000:00:00.0: pci rx: 00000020: cd 32 3b 06 .2;. [ 49.160000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e900 [ 49.160000] ath10k_pci 0000:00:00.0: chan info err_code 0 freq 5180 cmd_flags 1 noise_floor -105 rx_clear_count 1095103 cycle_count 104542925 [ 49.210000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 28 [ 49.210000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 01 00 14 00 00 21 00 00 0f 00 00 00 50 14 00 00 .....!......P... [ 49.210000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 50 14 00 00 00 00 00 00 00 00 00 00 P........... [ 49.210000] ath10k_pci 0000:00:00.0: pci hif send complete check [ 49.210000] ath10k_pci 0000:00:00.0: htc rx completion ep 1 skb 87813cc0 [ 49.210000] ath10k_pci 0000:00:00.0: htt rx, msg_type: 0xF [ 49.220000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 49.220000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 22 00 00 00 90 00 00 08 00 00 00 .....".......... [ 49.220000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 03 00 00 00 50 14 00 00 01 a0 00 00 00 a0 00 00 ....P........... [ 49.220000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 .... [ 49.220000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0e9c0 [ 49.220000] ath10k_pci 0000:00:00.0: scan event foreign channel type 8 reason 3 freq 5200 req_id 40961 scan_id 40960 vdev_id 0 state running (2) [ 49.220000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 49.220000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 23 00 00 0c 90 00 00 00 00 00 00 .....#.......... [ 49.220000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 50 14 00 00 00 00 00 00 00 00 00 00 96 b6 10 00 P............... [ 49.220000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 39 e0 83 06 9... [ 49.220000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0ea80 [ 49.220000] ath10k_pci 0000:00:00.0: chan info err_code 0 freq 5200 cmd_flags 0 noise_floor 0 rx_clear_count 1095318 cycle_count 109305913 [ 49.360000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 49.360000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 24 00 00 00 90 00 00 04 00 00 00 .....$.......... [ 49.360000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 03 00 00 00 50 14 00 00 01 a0 00 00 00 a0 00 00 ....P........... [ 49.360000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 .... [ 49.360000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0eb40 [ 49.360000] ath10k_pci 0000:00:00.0: scan event bss channel type 4 reason 3 freq 5200 req_id 40961 scan_id 40960 vdev_id 0 state running (2) [ 49.360000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 49.360000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 25 00 00 0c 90 00 00 00 00 00 00 .....%.......... [ 49.360000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 50 14 00 00 01 00 00 00 97 ff ff ff 96 b6 10 00 P............... [ 49.360000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 2d f6 47 07 -.G. [ 49.360000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0ec00 [ 49.360000] ath10k_pci 0000:00:00.0: chan info err_code 0 freq 5200 cmd_flags 1 noise_floor -105 rx_clear_count 1095318 cycle_count 122156589 [ 49.410000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 49.410000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 1c 00 00 26 00 00 00 90 00 00 02 00 00 00 .....&.......... [ 49.410000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 00 00 00 00 50 14 00 00 01 a0 00 00 00 a0 00 00 ....P........... [ 49.410000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 .... [ 49.410000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0ecc0 [ 49.410000] ath10k_pci 0000:00:00.0: scan event completed type 2 reason 0 freq 5200 req_id 40961 scan_id 40960 vdev_id 0 state running (2) [ 49.420000] ath10k_pci 0000:00:00.0: mac config channel 5180MHz flags 0x20 radar 0 [ 49.420000] ath10k_pci 0000:00:00.0: mac config channel to 5180MHz (cf1 5210MHz cf2 0MHz width 80) [ 49.420000] ath10k_pci 0000:00:00.0: wmi mgmt vdev down id 0x1 [ 49.420000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 49.420000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e95140 len 16 n_items 1 [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 08 00 00 20 00 65 16 90 00 00 01 00 00 00 ..... .e........ [ 49.420000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 87813a80 [ 49.420000] ath10k_pci 0000:00:00.0: wmi vdev stop id 0x1 [ 49.420000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 49.420000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 49.420000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e95260 len 16 n_items 1 [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 08 00 00 21 00 08 15 90 00 00 01 00 00 00 .....!.......... [ 49.420000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0ecc0 [ 49.420000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 24 [ 49.420000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 02 10 00 08 27 00 00 07 90 00 00 01 00 00 00 .....'.......... [ 49.420000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 01 04 00 00 02 01 00 00 ........ [ 49.420000] ath10k_pci 0000:00:00.0: htc ep 2 got 1 credits (total 1) [ 49.420000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0ed80 [ 49.420000] ath10k_pci 0000:00:00.0: WMI_VDEV_STOPPED_EVENTID [ 49.420000] ath10k_pci 0000:00:00.0: mac monitor vdev 1 stopped [ 49.420000] ath10k_pci 0000:00:00.0: WMI vdev delete id 1 [ 49.420000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 49.420000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 49.420000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e95c80 len 16 n_items 1 [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 08 00 00 22 00 00 11 90 00 00 01 00 00 00 .....".......... [ 49.420000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0ecc0 [ 49.420000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 49.420000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 28 00 00 01 04 00 01 02 02 b4 06 .....(.......... [ 49.420000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 49.420000] ath10k_pci 0000:00:00.0: mac monitor vdev 1 deleted [ 49.420000] ath10k_pci 0000:00:00.0: mac monitor stopped [ 49.420000] ath10k_pci 0000:00:00.0: mac monitor recalc started? 0 should? 1 [ 49.420000] ath10k_pci 0000:00:00.0: WMI vdev create: id 1 type 4 subtype 0 macaddr 04:f0:21:0c:a5:44 [ 49.420000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 49.420000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e966a0 len 32 n_items 1 [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 18 00 00 23 00 00 10 90 00 00 01 00 00 00 .....#.......... [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 04 00 00 00 00 00 00 00 04 f0 21 0c a5 44 00 00 ..........!..D.. [ 49.420000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0ec00 [ 49.420000] ath10k_pci 0000:00:00.0: mac monitor vdev 1 created [ 49.420000] ath10k_pci 0000:00:00.0: wmi vdev start id 0x1 flags: 0x0, freq 5180, mode 10, ch_flags: 0xA000000, max_power: 34 [ 49.420000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 49.420000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 49.420000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x06e967c0 len 140 n_items 1 [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 84 00 00 24 00 00 12 90 00 00 3c 14 00 00 .....$......<... [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 5a 14 00 00 00 00 00 00 0a 00 00 00 00 22 22 00 Z............"". [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 ................ [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 49.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000080: 00 00 00 00 00 00 00 00 00 00 00 00 ............ [ 49.420000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0ec00 [ 49.420000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 49.420000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 29 00 00 01 04 00 01 02 02 b4 06 .....).......... [ 49.420000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 49.420000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 28 [ 49.420000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 01 00 14 00 00 2a 00 00 0f 00 00 00 3c 14 00 00 .....*......<... [ 49.420000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 5a 14 00 00 00 00 00 00 0a 00 00 00 Z........... [ 49.420000] ath10k_pci 0000:00:00.0: pci hif send complete check [ 49.420000] ath10k_pci 0000:00:00.0: htc rx completion ep 1 skb 87813d80 [ 49.420000] ath10k_pci 0000:00:00.0: htt rx, msg_type: 0xF [ 49.430000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 28 [ 49.430000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 14 00 00 2b 00 00 04 90 00 00 01 00 00 00 .....+.......... [ 49.430000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 ............ [ 49.430000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0ee40 [ 49.430000] ath10k_pci 0000:00:00.0: WMI_VDEV_START_RESP_EVENTID [ 49.430000] ath10k_pci 0000:00:00.0: wmi mgmt vdev up id 0x1 assoc id 0 bssid 04:f0:21:0c:a5:44 [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 49.430000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a0940 len 28 n_items 1 [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 14 00 00 25 00 00 14 90 00 00 01 00 00 00 .....%.......... [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 00 00 00 00 04 f0 21 0c a5 44 00 00 ......!..D.. [ 49.430000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0ea80 [ 49.430000] ath10k_pci 0000:00:00.0: mac monitor vdev 1 started [ 49.430000] ath10k_pci 0000:00:00.0: mac monitor started [ 49.430000] ath10k_pci 0000:00:00.0: mac vdev_id 0 txpower 17 [ 49.430000] ath10k_pci 0000:00:00.0: mac txpower 17 [ 49.430000] ath10k_pci 0000:00:00.0: wmi pdev set param 3 value 34 [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 49.430000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 49.430000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a0a60 len 20 n_items 1 [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 0c 00 00 26 00 00 06 90 00 00 03 00 00 00 .....&.......... [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 22 00 00 00 "... [ 49.430000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0ea80 [ 49.430000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 49.430000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 2c 00 00 01 04 00 01 02 02 b4 06 .....,.......... [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 49.430000] ath10k_pci 0000:00:00.0: wmi pdev set param 4 value 34 [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 49.430000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a0b80 len 20 n_items 1 [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 0c 00 00 27 00 00 06 90 00 00 04 00 00 00 .....'.......... [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 22 00 00 00 "... [ 49.430000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0e9c0 [ 49.430000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 3 value 100 [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 49.430000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 49.430000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a15a0 len 24 n_items 1 [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 10 00 00 28 00 00 19 90 00 00 00 00 00 00 .....(.......... [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 03 00 00 00 64 00 00 00 ....d... [ 49.430000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0e9c0 [ 49.430000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 49.430000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 2d 00 00 01 04 00 01 02 02 b4 06 .....-.......... [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 49.430000] ath10k_pci 0000:00:00.0: mac vdev 0 beacon_interval 100 [ 49.430000] ath10k_pci 0000:00:00.0: vdev 0 set beacon tx mode to staggered [ 49.430000] ath10k_pci 0000:00:00.0: wmi pdev set param 7 value 0 [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 49.430000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a1fc0 len 20 n_items 1 [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 0c 00 00 29 00 00 06 90 00 00 07 00 00 00 .....).......... [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 00 00 00 00 .... [ 49.430000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0e900 [ 49.430000] ath10k_pci 0000:00:00.0: mac vdev 0 dtim_period 2 [ 49.430000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 13 value 2 [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 49.430000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 49.430000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a20e0 len 24 n_items 1 [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 10 00 00 2a 00 00 19 90 00 00 00 00 00 00 .....*.......... [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 0d 00 00 00 02 00 00 00 ........ [ 49.430000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0e900 [ 49.430000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 49.430000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 2e 00 00 01 04 00 01 02 02 b4 06 ................ [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 49.430000] ath10k_pci 0000:00:00.0: mac vdev 0 start center_freq 5180 phymode 11ac-vht80 [ 49.430000] ath10k_pci 0000:00:00.0: wmi vdev start id 0x0 flags: 0x0, freq 5180, mode 10, ch_flags: 0xA000000, max_power: 34 [ 49.430000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 49.430000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a2b00 len 140 n_items 1 [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 84 00 00 2b 00 00 12 90 00 00 3c 14 00 00 .....+......<... [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 5a 14 00 00 00 00 00 00 0a 00 00 00 00 22 22 00 Z............"". [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 64 00 00 00 ............d... [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 02 00 00 00 00 00 00 00 07 00 00 00 4f 70 65 6e ............Open [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 57 72 74 00 00 00 00 00 00 00 00 00 00 00 00 00 Wrt............. [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 49.430000] ath10k_pci 0000:00:00.0: pci tx data: 00000080: 00 00 00 00 00 00 00 00 00 00 00 00 ............ [ 49.430000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0e840 [ 50.420000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 36 [ 50.420000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 02 1c 00 08 2f 00 00 04 90 00 00 00 00 00 00 ...../.......... [ 50.420000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 01 04 00 00 ................ [ 50.420000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 02 01 00 00 .... [ 50.420000] ath10k_pci 0000:00:00.0: htc ep 2 got 1 credits (total 2) [ 50.420000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0ef00 [ 50.420000] ath10k_pci 0000:00:00.0: WMI_VDEV_START_RESP_EVENTID [ 50.420000] ath10k_pci 0000:00:00.0: wmi mgmt vdev up id 0x0 assoc id 0 bssid 04:f0:21:0c:a5:44 [ 50.420000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 50.420000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a35a0 len 28 n_items 1 [ 50.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 14 00 00 2c 00 00 14 90 00 00 00 00 00 00 .....,.......... [ 50.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 00 00 00 00 04 f0 21 0c a5 44 00 00 ......!..D.. [ 50.420000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0e840 [ 50.420000] ath10k_pci 0000:00:00.0: mac vdev 0 up [ 50.420000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 80 [ 50.420000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 48 00 00 30 00 00 0a 90 00 00 01 00 00 00 ..H..0.......... [ 50.420000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.420000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.420000] ath10k_pci 0000:00:00.0: pci rx: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.420000] ath10k_pci 0000:00:00.0: pci rx: 00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.420000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0f000 [ 50.420000] ath10k_pci 0000:00:00.0: WMI_TBTTOFFSET_UPDATE_EVENTID [ 50.420000] ath10k_pci 0000:00:00.0: mac vdev_id 0 txpower 17 [ 50.420000] ath10k_pci 0000:00:00.0: mac txpower 17 [ 50.420000] ath10k_pci 0000:00:00.0: wmi pdev set param 3 value 34 [ 50.420000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 50.420000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 50.420000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a3fc0 len 20 n_items 1 [ 50.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 0c 00 00 2d 00 a7 06 90 00 00 03 00 00 00 .....-.......... [ 50.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 22 00 00 00 "... [ 50.420000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0e780 [ 50.420000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 50.420000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 31 00 00 01 04 00 01 02 02 b4 06 .....1.......... [ 50.420000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 50.420000] ath10k_pci 0000:00:00.0: wmi pdev set param 4 value 34 [ 50.420000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 50.420000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a40e0 len 20 n_items 1 [ 50.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 0c 00 00 2e 00 01 06 90 00 00 04 00 00 00 ................ [ 50.420000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 22 00 00 00 "... [ 50.420000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 86e0e6c0 [ 50.420000] br-lan: port 2(wlan0) entered forwarding state [ 50.430000] br-lan: port 2(wlan0) entered forwarding state [ 50.430000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 50.440000] ath10k_pci 0000:00:00.0: mac vdev 0 cts_prot 0 [ 50.440000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 43 value 0 [ 50.440000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 50.440000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 50.440000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a4da0 len 24 n_items 1 [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 10 00 00 2f 00 00 19 90 00 00 00 00 00 00 ...../.......... [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 2b 00 00 00 00 00 00 00 +....... [ 50.440000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 50.440000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 32 00 00 01 04 00 01 02 02 b4 06 .....2.......... [ 50.440000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 50.440000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df0c0 [ 50.440000] ath10k_pci 0000:00:00.0: mac vdev 0 slot_time 2 [ 50.440000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 7 value 2 [ 50.440000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 50.440000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a57c0 len 24 n_items 1 [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 10 00 00 30 00 00 19 90 00 00 00 00 00 00 .....0.......... [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 07 00 00 00 02 00 00 00 ........ [ 50.440000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df0c0 [ 50.440000] ath10k_pci 0000:00:00.0: mac vdev 0 preamble 2n [ 50.440000] ath10k_pci 0000:00:00.0: wmi vdev id 0x0 set param 8 value 2 [ 50.440000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 50.440000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 50.440000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a58e0 len 24 n_items 1 [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 10 00 00 31 00 00 19 90 00 00 00 00 00 00 .....1.......... [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 08 00 00 00 02 00 00 00 ........ [ 50.440000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df0c0 [ 50.440000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 50.440000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 33 00 00 01 04 00 01 02 02 b4 06 .....3.......... [ 50.440000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 50.440000] ath10k_pci 0000:00:00.0: wmi pdev set wmm params [ 50.440000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 50.440000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a6300 len 108 n_items 1 [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 64 00 00 32 00 00 09 90 00 00 0f 00 00 00 ..d..2.......... [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: ff 03 00 00 03 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 0f 00 00 00 ff 03 00 00 07 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 0f 00 00 00 02 00 00 00 c0 0b 00 00 00 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 03 00 00 00 07 00 00 00 01 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: e0 05 00 00 00 00 00 00 00 00 00 00 ............ [ 50.440000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df180 [ 50.440000] ath10k_pci 0000:00:00.0: wmi pdev set wmm params [ 50.440000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 50.440000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 50.440000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a6480 len 108 n_items 1 [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 64 00 00 33 00 00 09 90 00 00 0f 00 00 00 ..d..3.......... [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: ff 03 00 00 03 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 0f 00 00 00 ff 03 00 00 07 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 0f 00 00 00 01 00 00 00 c0 0b 00 00 00 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 03 00 00 00 07 00 00 00 01 00 00 00 ................ [ 50.440000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: e0 05 00 00 00 00 00 00 00 00 00 00 ............ [ 50.440000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df3c0 [ 50.450000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 50.450000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 34 00 00 01 04 00 01 02 02 b4 06 .....4.......... [ 50.450000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 50.450000] ath10k_pci 0000:00:00.0: mac monitor recalc started? 1 should? 1 [ 50.450000] ath10k_pci 0000:00:00.0: wmi pdev set wmm params [ 50.450000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 50.450000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a6f00 len 108 n_items 1 [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 64 00 00 34 00 00 09 90 00 00 0f 00 00 00 ..d..4.......... [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 3f 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 ?............... [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 0f 00 00 00 ff 03 00 00 07 00 00 00 ................ [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 ................ [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 0f 00 00 00 01 00 00 00 c0 0b 00 00 00 00 00 00 ................ [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 03 00 00 00 07 00 00 00 01 00 00 00 ................ [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: e0 05 00 00 00 00 00 00 00 00 00 00 ............ [ 50.450000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df0c0 [ 50.450000] ath10k_pci 0000:00:00.0: wmi pdev set wmm params [ 50.450000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 50.450000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 50.450000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a7080 len 108 n_items 1 [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 64 00 00 35 00 00 09 90 00 00 0f 00 00 00 ..d..5.......... [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 3f 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 ?............... [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 00 00 00 00 0f 00 00 00 ff 03 00 00 07 00 00 00 ................ [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 07 00 00 00 ................ [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 0f 00 00 00 01 00 00 00 c0 0b 00 00 00 00 00 00 ................ [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 03 00 00 00 07 00 00 00 01 00 00 00 ................ [ 50.450000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: e0 05 00 00 00 00 00 00 00 00 00 00 ............ [ 50.450000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df3c0 [ 50.450000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 16 [ 50.450000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 02 08 00 08 35 00 00 01 04 00 01 02 02 b4 06 .....5.......... [ 50.450000] ath10k_pci 0000:00:00.0: htc ep 2 got 2 credits (total 2) [ 50.510000] ath10k_pci 0000:00:00.0: mac monitor recalc started? 1 should? 1 [ 50.620000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 48 [ 50.620000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 28 00 00 36 00 00 09 90 00 00 01 00 00 00 ..(..6.......... [ 50.620000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.620000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.620000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0f0c0 [ 50.620000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 50.620000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066a7dc0 len 40 n_items 1 [ 50.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 20 00 00 36 00 00 57 90 00 00 00 00 00 00 .. ..6..W....... [ 50.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: ad 00 00 00 00 d0 5d 06 00 00 00 00 80 00 00 00 ......]......... [ 50.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 03 00 00 00 00 00 00 00 ........ [ 50.620000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df540 [ 50.730000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 56 [ 50.730000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 02 30 00 08 37 00 00 09 90 00 00 01 00 00 00 ..0..7.......... [ 50.730000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.730000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 50.730000] ath10k_pci 0000:00:00.0: pci rx: 00000030: 01 04 00 00 02 01 00 00 ........ [ 50.730000] ath10k_pci 0000:00:00.0: htc ep 2 got 1 credits (total 2) [ 50.730000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86e0f180 [ 50.730000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 50.730000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066b0c00 len 40 n_items 1 [ 50.730000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 20 00 00 37 00 00 57 90 00 00 00 00 00 00 .. ..7..W....... [ 50.730000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: ad 00 00 00 00 d0 5d 06 00 00 00 00 80 00 00 00 ......]......... [ 50.730000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 03 00 00 00 00 00 00 00 ........ [ 50.800000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 8b69d64c-1774-462c-8dd8-3d72d32da547) [ 50.810000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 50.820000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 50.840000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16 [ 50.850000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16 [ 50.860000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 50.870000] ath10k_pci 0000:00:00.0: boot hif stop [ 50.870000] ath10k_pci 0000:00:00.0: boot warm reset [ 50.910000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 50.910000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 50.910000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 50.910000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 50.910000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 50.910000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 50.910000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 50.910000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 50.910000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 50.920000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 50.930000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 50.930000] ath10k_pci 0000:00:00.0: boot target initialised [ 50.950000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 50.950000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 50.950000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 50.950000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 50.950000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 50.950000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 50.950000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 50.950000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 50.950000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 50.960000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 50.970000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 50.970000] ath10k_pci 0000:00:00.0: boot target initialised [ 50.970000] ath10k_pci 0000:00:00.0: boot warm reset complete [ 50.970000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df0c0 [ 50.970000] ieee80211 phy0: Hardware restart was requested [ 50.970000] ath10k_pci 0000:00:00.0: wmi mgmt vdev down id 0x1 [ 50.970000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 0) [ 50.970000] ath10k_pci 0000:00:00.0: HTC: endpoint 2 needs credit update [ 50.970000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x066b1640 len 16 n_items 1 [ 50.970000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 01 08 00 00 38 00 00 16 90 00 00 01 00 00 00 .....8.......... [ 50.970000] ath10k_pci 0000:00:00.0: wmi vdev stop id 0x1 [ 50.970000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143 [ 50.980000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143 [ 50.990000] ath10k_pci 0000:00:00.0: mac monitor vdev 1 stopped [ 50.990000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 [ 51.000000] ath10k_pci 0000:00:00.0: wmi disable pktlog [ 51.000000] ath10k_pci 0000:00:00.0: boot hif stop [ 51.000000] ath10k_pci 0000:00:00.0: boot warm reset [ 51.040000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.040000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.040000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.040000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.040000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.040000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.040000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.040000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 51.040000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.050000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.060000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 51.060000] ath10k_pci 0000:00:00.0: boot target initialised [ 51.080000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.080000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.080000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.080000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.080000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.080000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.080000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.080000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 51.080000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.090000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.100000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 51.100000] ath10k_pci 0000:00:00.0: boot target initialised [ 51.100000] ath10k_pci 0000:00:00.0: boot warm reset complete [ 51.100000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 865df0c0 [ 51.100000] ath10k_pci 0000:00:00.0: boot hif power down [ 51.100000] ath10k_pci 0000:00:00.0: boot hif power up [ 51.100000] ath10k_pci 0000:00:00.0: boot 988x chip reset [ 51.100000] ath10k_pci 0000:00:00.0: boot warm reset [ 51.140000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.140000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.140000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.140000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.140000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.140000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.140000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.140000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 51.140000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.150000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.160000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 51.160000] ath10k_pci 0000:00:00.0: boot target initialised [ 51.180000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.180000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.180000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.180000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.180000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.180000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.180000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.180000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 51.180000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.190000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.200000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 51.200000] ath10k_pci 0000:00:00.0: boot target initialised [ 51.200000] ath10k_pci 0000:00:00.0: boot warm reset complete [ 51.200000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.200000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.200000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.200000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.200000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.200000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.200000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.210000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 51.220000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 51.220000] ath10k_pci 0000:00:00.0: boot warm reset [ 51.260000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.260000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.260000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.260000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.260000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.260000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.260000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.260000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 51.260000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.270000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.280000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 51.280000] ath10k_pci 0000:00:00.0: boot target initialised [ 51.300000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.300000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.300000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.300000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.300000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.300000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.300000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.300000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 51.300000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.310000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.320000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 51.320000] ath10k_pci 0000:00:00.0: boot target initialised [ 51.320000] ath10k_pci 0000:00:00.0: boot warm reset complete [ 51.320000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.320000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.320000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.320000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.320000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.320000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.320000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.330000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 51.340000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 51.340000] ath10k_pci 0000:00:00.0: boot warm reset [ 51.380000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.380000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.380000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.380000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.380000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.380000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.380000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.380000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 51.380000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.390000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.400000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 51.400000] ath10k_pci 0000:00:00.0: boot target initialised [ 51.420000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.420000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.420000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.420000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.420000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.420000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.420000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.420000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 51.420000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.430000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.440000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 51.440000] ath10k_pci 0000:00:00.0: boot target initialised [ 51.440000] ath10k_pci 0000:00:00.0: boot warm reset complete [ 51.440000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.440000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.440000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.440000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.440000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.440000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.440000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.450000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 51.460000] ath10k_pci 0000:00:00.0: boot cold reset [ 51.500000] ath10k_pci 0000:00:00.0: boot cold reset complete [ 51.500000] ath10k_pci 0000:00:00.0: boot waiting target to initialise [ 51.500000] ath10k_pci 0000:00:00.0: boot target indicator 0 [ 51.510000] ath10k_pci 0000:00:00.0: boot target indicator 2 [ 51.510000] ath10k_pci 0000:00:00.0: boot target initialised [ 51.510000] ath10k_pci 0000:00:00.0: boot qca988x chip reset complete (cold) [ 51.510000] ath10k_pci 0000:00:00.0: boot init ce src ring id 0 entries 16 base_addr a71e2000 [ 51.510000] ath10k_pci 0000:00:00.0: boot ce dest ring id 1 entries 512 base_addr a70be000 [ 51.510000] ath10k_pci 0000:00:00.0: boot ce dest ring id 2 entries 32 base_addr a71d0000 [ 51.510000] ath10k_pci 0000:00:00.0: boot init ce src ring id 3 entries 32 base_addr a71d1000 [ 51.510000] ath10k_pci 0000:00:00.0: boot init ce src ring id 4 entries 4096 base_addr a7150000 [ 51.510000] ath10k_pci 0000:00:00.0: boot init ce src ring id 7 entries 2 base_addr a71d2000 [ 51.510000] ath10k_pci 0000:00:00.0: boot ce dest ring id 7 entries 2 base_addr a71d3000 [ 51.520000] ath10k_pci 0000:00:00.0: boot did not find a calibration file, try DT next: -11 [ 51.520000] ath10k_pci 0000:00:00.0: boot did not find DT entry, try OTP next: -2 [ 51.520000] ath10k_pci 0000:00:00.0: boot push board extended data addr 0x0 [ 51.520000] ath10k_pci 0000:00:00.0: boot upload otp to 0x1234 len 7205 [ 51.610000] ath10k_pci 0000:00:00.0: boot otp execute result 0 [ 51.610000] ath10k_pci 0000:00:00.0: boot using calibration mode otp [ 51.610000] ath10k_pci 0000:00:00.0: boot uploading firmware image c0361c64 len 234918 mode normal [ 52.430000] br-lan: port 2(wlan0) entered forwarding state [ 52.610000] ath10k_pci 0000:00:00.0: pci hif set callbacks [ 52.610000] ath10k_pci 0000:00:00.0: pci hif get default pipe [ 52.610000] ath10k_pci 0000:00:00.0: pci hif map service [ 52.610000] ath10k_pci 0000:00:00.0: htt tx max num pending tx 1424 [ 52.610000] ath10k_pci 0000:00:00.0: htt rx ring size 2048 fill_level 1023 [ 52.610000] ath10k_pci 0000:00:00.0: boot hif start [ 52.610000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 20 [ 52.610000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 00 0c 00 00 00 00 00 01 00 02 00 00 07 16 00 ................ [ 52.610000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 01 00 00 00 .... [ 52.620000] ath10k_pci 0000:00:00.0: Target ready! transmit resources: 2 size:1792 [ 52.620000] ath10k_pci 0000:00:00.0: pci hif map service [ 52.620000] ath10k_pci 0000:00:00.0: boot htc service 'Control' ul pipe 0 dl pipe 1 eid 0 ready [ 52.620000] ath10k_pci 0000:00:00.0: boot htc ep 0 ul polled 0 dl polled 0 [ 52.620000] ath10k_pci 0000:00:00.0: boot htc service 'Control' eid 0 TX flow control disabled [ 52.620000] ath10k_pci 0000:00:00.0: boot htc service HTT Data does not allocate target credits [ 52.620000] ath10k_pci 0000:00:00.0: ath10k_htc_build_tx_ctrl_skb: skb 864cf780 [ 52.620000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x064e004c len 16 n_items 1 [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 00 00 08 00 00 06 00 00 02 00 00 03 08 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 0 skb 864cf780 [ 52.620000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 20 [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 00 0c 00 00 01 00 00 03 00 00 03 00 01 d0 07 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 00 00 00 00 .... [ 52.620000] ath10k_pci 0000:00:00.0: HTC Service HTT Data connect response: status: 0x0, assigned ep: 0x1 [ 52.620000] ath10k_pci 0000:00:00.0: pci hif map service [ 52.620000] ath10k_pci 0000:00:00.0: boot htc service 'HTT Data' ul pipe 4 dl pipe 1 eid 1 ready [ 52.620000] ath10k_pci 0000:00:00.0: boot htc ep 1 ul polled 1 dl polled 0 [ 52.620000] ath10k_pci 0000:00:00.0: boot htc service 'HTT Data' eid 1 TX flow control disabled [ 52.620000] ath10k_pci 0000:00:00.0: ath10k_htc_build_tx_ctrl_skb: skb 864cf840 [ 52.620000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x064e0b6c len 16 n_items 1 [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 00 00 08 00 00 07 00 00 02 00 00 01 00 02 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 0 skb 864cf840 [ 52.620000] ath10k_pci 0000:00:00.0: pci rx ce pipe 1 len 20 [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 00 00 0c 00 00 02 00 00 03 00 00 01 00 02 b4 06 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 00 00 00 00 .... [ 52.620000] ath10k_pci 0000:00:00.0: HTC Service WMI connect response: status: 0x0, assigned ep: 0x2 [ 52.620000] ath10k_pci 0000:00:00.0: pci hif map service [ 52.620000] ath10k_pci 0000:00:00.0: boot htc service 'WMI' ul pipe 3 dl pipe 2 eid 2 ready [ 52.620000] ath10k_pci 0000:00:00.0: boot htc ep 2 ul polled 0 dl polled 0 [ 52.620000] ath10k_pci 0000:00:00.0: ath10k_htc_build_tx_ctrl_skb: skb 864cf900 [ 52.620000] ath10k_pci 0000:00:00.0: HTC is using TX credit flow control [ 52.620000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x064e168c len 20 n_items 1 [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 00 00 0c 00 00 08 00 00 05 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 00 00 00 00 .... [ 52.620000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 0 skb 864cf900 [ 52.620000] ath10k_pci 0000:00:00.0: pci rx ce pipe 2 len 180 [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000000: 02 00 ac 00 00 03 00 00 00 80 00 00 30 00 00 41 ............0..A [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000010: 01 00 00 00 01 00 00 00 0a 00 00 00 0e 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000020: 07 00 00 00 07 00 00 00 09 00 00 00 0f 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000030: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000050: 00 00 00 00 00 00 00 00 00 00 00 00 03 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000060: 5b 08 00 00 b2 01 80 33 ea ff 00 00 3f 00 00 00 [......3....?... [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000070: 3f 00 00 00 00 00 00 00 1f 00 00 00 07 00 00 00 ?............... [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000080: c0 0b 00 00 01 90 1f 00 08 09 00 00 ac 0a 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 00000090: 2e 13 00 00 d4 17 00 00 00 00 00 00 04 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 000000a0: 01 00 00 00 01 00 00 00 b8 01 00 00 02 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci rx: 000000b0: 00 00 00 00 .... [ 52.620000] ath10k_pci 0000:00:00.0: htc rx completion ep 2 skb 86521f00 [ 52.620000] ath10k_pci 0000:00:00.0: wmi svc: 00000000: 0e 00 00 00 07 00 00 00 07 00 00 00 09 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: wmi svc: 00000010: 0f 00 00 00 02 00 00 00 00 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: wmi svc: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: wmi svc: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: wmi mem_req_id 1 num_units 0 num_unit_info 2 unit size 440 actual units 145 [ 52.620000] ath10k_pci 0000:00:00.0: wmi event service ready min_tx_power 0x0000003f max_tx_power 0x0000003f ht_cap 0x0000085b vht_cap 0x338001b2 sw_ver0 0x41000030 sw_ver1 0x00000000 fw_build 0x00000000 phy_capab 0x00000001 num_rf_chains 0x00000003 eeprom_rd 0x00000000 num_mem_reqs 0x00000001 [ 52.620000] ath10k_pci 0000:00:00.0: firmware 10.2.4.48 booted [ 52.620000] ath10k_pci 0000:00:00.0: wmi chunk 0 len 63800 requested, addr 0x64f0000 [ 52.620000] ath10k_pci 0000:00:00.0: wmi init 10.2 [ 52.620000] ath10k_pci 0000:00:00.0: htc ep 2 consumed 1 credits (total 1) [ 52.620000] ath10k_pci 0000:00:00.0: pci tx item 0 paddr 0x064e21a0 len 176 n_items 1 [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000000: 02 00 a8 00 00 39 00 00 00 a0 00 00 10 00 00 00 .....9.......... [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000010: 90 00 00 00 02 00 00 00 00 01 00 00 10 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000020: 07 00 00 00 07 00 00 00 64 00 00 00 64 00 00 00 ........d...d... [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000030: 64 00 00 00 28 00 00 00 01 00 00 00 04 00 00 00 d...(........... [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000040: 02 00 00 00 02 00 00 00 08 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000050: 00 00 00 00 00 00 00 00 00 04 00 00 20 00 00 00 ............ ... [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000060: 01 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000070: 90 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 00000090: 01 00 00 00 01 00 00 00 01 00 00 00 00 00 4f 06 ..............O. [ 52.620000] ath10k_pci 0000:00:00.0: pci tx data: 000000a0: 38 f9 00 00 00 00 00 00 00 00 00 00 00 00 00 00 8............... [ 52.620000] ath10k_pci 0000:00:00.0: ath10k_htc_notify_tx_completion: ep 2 skb 864cf9c0 [-- Attachment #3: Type: text/plain, Size: 146 bytes --] _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-04-30 6:46 ` Yeoh Chun-Yeow @ 2015-04-30 7:05 ` Michal Kazior 2015-04-30 10:31 ` Yeoh Chun-Yeow 0 siblings, 1 reply; 17+ messages in thread From: Michal Kazior @ 2015-04-30 7:05 UTC (permalink / raw) To: Yeoh Chun-Yeow; +Cc: Kalle Valo, ath10k@lists.infradead.org On 30 April 2015 at 08:46, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: > Hi, Michal > > Attached is the partial log. Hopefully it is useful for you. Thanks. It looks like the device goes through the cold reset. I would expect the device to work after that. Maybe WLE900N5-23 board is wired differently or 10.2 doesn't reset a few HW registers anymore. Anyway, the device seems to crash after it's started and upped. It gets to transmit 2 beacons and then it crashes. I didn't see any Rx (WMI nor HTT) events which leads me to think that the HW MAC Rx may contain some invalid/stale DMA pointers which subsequently lead to CE failure and device CPU crash. If you could run the device on a x86 with IOMMU enabled it'd be probably possible to narrow down the search by looking at DMAR error addresses. Hmm.. I recall there are a few HW MAC Rx rings. Maybe 10.2 uses more than 10.1 did but doesn't reset them properly? I assume you need to reboot the machine before it starts to work again, no? Or does driver reload alone help? Did you try to `echo 1 > /sys/bus/pci/devices/xxxx:xx:xx.x/remove` and `echo 1 > /sys/bus/pci/rescan`? Or did you try to swap fw from 10.2 to 10.1 (needs driver reload) after the "bad bad crashes" start to appear? Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-04-30 7:05 ` Michal Kazior @ 2015-04-30 10:31 ` Yeoh Chun-Yeow 2015-04-30 10:50 ` Michal Kazior 0 siblings, 1 reply; 17+ messages in thread From: Yeoh Chun-Yeow @ 2015-04-30 10:31 UTC (permalink / raw) To: Michal Kazior; +Cc: Kalle Valo, ath10k@lists.infradead.org Hi, Michal > I assume you need to reboot the machine before it starts to work > again, no? Or does driver reload alone help? The system looks very sluggish once the firmware start to crash. But not required reboot. > Did you try to `echo 1 > > /sys/bus/pci/devices/xxxx:xx:xx.x/remove` and `echo 1 > > /sys/bus/pci/rescan`? > Or did you try to swap fw from 10.2 to 10.1 > (needs driver reload) after the "bad bad crashes" start to appear? > I try to load 10.1 after the firmware crashed on 10.2 and it is working. See log below. So no changes at all for this board to use 10.2 firmware? ---- Chun-Yeow [ 169.530000] ieee80211 phy0: Hardware restart was requested [ 172.110000] ath10k_pci 0000:00:00.0: device successfully recovered [ 172.450000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid 529a0c02-8d7b-4830-87ef-e491503db08c) [ 172.460000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2-00082-4-2 api 3 htt 2.1 wmi 3 cal otp max_sta 128 [ 172.480000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 172.500000] ath10k_warn: 12 callbacks suppressed [ 172.500000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16 [ 172.510000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16 [ 172.520000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 172.620000] ieee80211 phy0: Hardware restart was requested [ 172.620000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143 [ 172.630000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143 [ 172.640000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 [ 172.850000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 172.860000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 172.970000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 172.980000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 173.090000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 175.240000] ath10k_pci 0000:00:00.0: device successfully recovered [ 175.360000] br-lan: port 2(wlan0) entered disabled state [ 175.370000] device wlan0 left promiscuous mode [ 175.370000] br-lan: port 2(wlan0) entered disabled state [ 199.310000] pci 0000:00:00.0: [168c:003c] type 00 class 0x028000 [ 199.310000] pci 0000:00:00.0: reg 0x10: [mem 0x10000000-0x101fffff 64bit] [ 199.310000] pci 0000:00:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 199.310000] pci 0000:00:00.0: supports D1 D2 [ 199.310000] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 199.310000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [ 199.320000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [ 199.320000] ath10k_pci 0000:00:00.0: pci irq legacy interrupts 0 irq_mode 0 reset_mode 0 [ 199.540000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/cal-pci-0000:00:00.0.bin failed with error -2 [ 199.550000] ath10k_pci 0000:00:00.0: Falling back to user helper [ 199.640000] firmware ath10k!cal-pci-0000:00:00.0.bin: firmware_loading_store: map pages failed [ 199.650000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2 [ 199.660000] ath10k_pci 0000:00:00.0: Falling back to user helper [ 199.760000] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed [ 199.770000] ath10k_pci 0000:00:00.0: could not fetch firmware file 'ath10k/QCA988X/hw2.0/firmware-4.bin': -11 [ 199.780000] ath10k_pci 0000:00:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2 [ 199.790000] ath10k_pci 0000:00:00.0: Falling back to user helper [ 199.880000] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed [ 199.890000] ath10k_pci 0000:00:00.0: could not fetch firmware file 'ath10k/QCA988X/hw2.0/firmware-3.bin': -11 [ 201.060000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.1.467.2-1 api 2 htt 2.1 wmi 2 cal otp max_sta 128 [ 201.070000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 201.180000] ath: EEPROM regdomain: 0x0 [ 201.180000] ath: EEPROM indicates default country code should be used [ 201.180000] ath: doing EEPROM country->regdmn map search [ 201.180000] ath: country maps to regdmn code: 0x3a [ 201.180000] ath: Country alpha2 being used: US [ 201.180000] ath: Regpair used: 0x3a [ 202.310000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-04-30 10:31 ` Yeoh Chun-Yeow @ 2015-04-30 10:50 ` Michal Kazior 0 siblings, 0 replies; 17+ messages in thread From: Michal Kazior @ 2015-04-30 10:50 UTC (permalink / raw) To: Yeoh Chun-Yeow; +Cc: Kalle Valo, ath10k@lists.infradead.org On 30 April 2015 at 12:31, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: > Hi, Michal > >> I assume you need to reboot the machine before it starts to work >> again, no? Or does driver reload alone help? > > The system looks very sluggish once the firmware start to crash. But > not required reboot. I assume it's due to crash-restart going over and over which involves taking RTNL - this could reduce system responsiveness. >> Did you try to `echo 1 > >> /sys/bus/pci/devices/xxxx:xx:xx.x/remove` and `echo 1 > >> /sys/bus/pci/rescan`? >> Or did you try to swap fw from 10.2 to 10.1 >> (needs driver reload) after the "bad bad crashes" start to appear? >> > > I try to load 10.1 after the firmware crashed on 10.2 and it is > working. See log below. > > So no changes at all for this board to use 10.2 firmware? [...] Did you try to reload the driver alone (without changing firmware)? I'd like to know if it's actually 10.2 -> 10.1 that makes the crashing go away. Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
[parent not found: <CAEFj9871+uootjCDVNBEKSYiDJzdRcMLkWe=bKdmxKDKBCBbKA@mail.gmail.com>]
* Re: Compex WLE900N5-23 [not found] <CAEFj9871+uootjCDVNBEKSYiDJzdRcMLkWe=bKdmxKDKBCBbKA@mail.gmail.com> @ 2015-05-05 5:40 ` Yeoh Chun-Yeow 2015-05-05 5:47 ` Michal Kazior 0 siblings, 1 reply; 17+ messages in thread From: Yeoh Chun-Yeow @ 2015-05-05 5:40 UTC (permalink / raw) To: Michal Kazior; +Cc: Kalle Valo, ath10k@lists.infradead.org Hi, Michal Any idea on this issue? ---- Chun-Yeow On Thu, Apr 30, 2015 at 7:29 PM, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: > > On Apr 30, 2015 18:50, "Michal Kazior" <michal.kazior@tieto.com> wrote: >> >> On 30 April 2015 at 12:31, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >> > Hi, Michal >> > >> >> I assume you need to reboot the machine before it starts to work >> >> again, no? Or does driver reload alone help? >> > >> > The system looks very sluggish once the firmware start to crash. But >> > not required reboot. >> >> I assume it's due to crash-restart going over and over which involves >> taking RTNL - this could reduce system responsiveness. >> >> >> >> Did you try to `echo 1 > >> >> /sys/bus/pci/devices/xxxx:xx:xx.x/remove` and `echo 1 > >> >> /sys/bus/pci/rescan`? >> >> Or did you try to swap fw from 10.2 to 10.1 >> >> (needs driver reload) after the "bad bad crashes" start to appear? >> >> >> > >> > I try to load 10.1 after the firmware crashed on 10.2 and it is >> > working. See log below. >> > >> > So no changes at all for this board to use 10.2 firmware? >> [...] >> >> Did you try to reload the driver alone (without changing firmware)? > > You mean doing remove and rescan using 10.2 firmware? Yes, it crashed again. > > --- > Chun-Yeow _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-05-05 5:40 ` Yeoh Chun-Yeow @ 2015-05-05 5:47 ` Michal Kazior 2015-05-05 5:56 ` Yeoh Chun-Yeow 0 siblings, 1 reply; 17+ messages in thread From: Michal Kazior @ 2015-05-05 5:47 UTC (permalink / raw) To: Yeoh Chun-Yeow; +Cc: Kalle Valo, ath10k@lists.infradead.org On 5 May 2015 at 07:40, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: > Hi, Michal > > Any idea on this issue? Did you try more recent 10.2.4 firmware revisions? My guess is that 10.2-00082 introduced some kind of regression and doesn't reset the entire HW MAC state. I'd bet on Rx ring (there's a few of them and host can only use one of them) since from the logs you've provided it looks like after starting up interface there's no single Rx event to be seen and it is very likely that Rx triggers the hard crash due to invalid/stale memory pointer. Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-05-05 5:47 ` Michal Kazior @ 2015-05-05 5:56 ` Yeoh Chun-Yeow 2015-05-05 6:49 ` Michal Kazior 0 siblings, 1 reply; 17+ messages in thread From: Yeoh Chun-Yeow @ 2015-05-05 5:56 UTC (permalink / raw) To: Michal Kazior; +Cc: Kalle Valo, ath10k@lists.infradead.org Yes, this is the latest firmware that I have tried: ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 But still the same, firmware crashed: [ 154.920000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -11 [ 159.920000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -145 [ 159.920000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 [ 159.930000] ath10k_pci 0000:00:00.0: failed to recalc montior: -145 [ 162.940000] ath10k_pci 0000:00:00.0: failed to stop WMI vdev 0: -11 [ 165.940000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 [ 168.940000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -11 [ 173.940000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -145 [ 173.940000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 [ 176.950000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 [ 179.950000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -11 [ 184.950000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -145 [ 184.950000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 [ 187.960000] ath10k_pci 0000:00:00.0: failed to submit AP self-peer removal on vdev 0: -11 [ 190.960000] ath10k_pci 0000:00:00.0: failed to delete WMI vdev 0: -11 [ 193.960000] ath10k_pci 0000:00:00.0: failed to remove AP self-peer on vdev 0: -145 [ 193.960000] ath10k_pci 0000:00:00.0: removing stale peer 04:f0:21:0c:a5:17 from vdev_id 0 [ 196.970000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 --- Chun-Yeow On Tue, May 5, 2015 at 1:47 PM, Michal Kazior <michal.kazior@tieto.com> wrote: > On 5 May 2015 at 07:40, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >> Hi, Michal >> >> Any idea on this issue? > > Did you try more recent 10.2.4 firmware revisions? > > My guess is that 10.2-00082 introduced some kind of regression and > doesn't reset the entire HW MAC state. I'd bet on Rx ring (there's a > few of them and host can only use one of them) since from the logs > you've provided it looks like after starting up interface there's no > single Rx event to be seen and it is very likely that Rx triggers the > hard crash due to invalid/stale memory pointer. > > > Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-05-05 5:56 ` Yeoh Chun-Yeow @ 2015-05-05 6:49 ` Michal Kazior 2015-05-05 11:11 ` Yeoh Chun-Yeow 0 siblings, 1 reply; 17+ messages in thread From: Michal Kazior @ 2015-05-05 6:49 UTC (permalink / raw) To: Yeoh Chun-Yeow; +Cc: Kalle Valo, ath10k@lists.infradead.org On 5 May 2015 at 07:56, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: > Yes, this is the latest firmware that I have tried: > > ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw > 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 > > But still the same, firmware crashed: > [ 154.920000] ath10k_pci 0000:00:00.0: failed to to request monitor > vdev 1 stop: -11 > [ 159.920000] ath10k_pci 0000:00:00.0: failed to synchronize monitor > vdev 1 stop: -145 > [ 159.920000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 > [ 159.930000] ath10k_pci 0000:00:00.0: failed to recalc montior: -145 > [ 162.940000] ath10k_pci 0000:00:00.0: failed to stop WMI vdev 0: -11 > [ 165.940000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 > [ 168.940000] ath10k_pci 0000:00:00.0: failed to to request monitor > vdev 1 stop: -11 > [ 173.940000] ath10k_pci 0000:00:00.0: failed to synchronize monitor > vdev 1 stop: -145 > [ 173.940000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 > [ 176.950000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 > [ 179.950000] ath10k_pci 0000:00:00.0: failed to to request monitor > vdev 1 stop: -11 > [ 184.950000] ath10k_pci 0000:00:00.0: failed to synchronize monitor > vdev 1 stop: -145 > [ 184.950000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 > [ 187.960000] ath10k_pci 0000:00:00.0: failed to submit AP self-peer > removal on vdev 0: -11 > [ 190.960000] ath10k_pci 0000:00:00.0: failed to delete WMI vdev 0: -11 > [ 193.960000] ath10k_pci 0000:00:00.0: failed to remove AP self-peer > on vdev 0: -145 > [ 193.960000] ath10k_pci 0000:00:00.0: removing stale peer > 04:f0:21:0c:a5:17 from vdev_id 0 > [ 196.970000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 Hmm.. Can you try to repack firmware and combine main binary from 10.2 and otp from 10.1 and test that? You can use these tools: https://gist.github.com/kazikcz/64313b9e2470660faae1 https://gist.github.com/kazikcz/c970cbf3a863ebbc4495 Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-05-05 6:49 ` Michal Kazior @ 2015-05-05 11:11 ` Yeoh Chun-Yeow 2015-05-05 11:19 ` Michal Kazior 0 siblings, 1 reply; 17+ messages in thread From: Yeoh Chun-Yeow @ 2015-05-05 11:11 UTC (permalink / raw) To: Michal Kazior; +Cc: Kalle Valo, ath10k@lists.infradead.org What to be set for "VERSION_STRING DECIMAL_BITMASK_OF_FEATURES" for assembly? I ran into this error "IndexError: list index out of range" during assembly. --- Chun-Yeow On Tue, May 5, 2015 at 2:49 PM, Michal Kazior <michal.kazior@tieto.com> wrote: > On 5 May 2015 at 07:56, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >> Yes, this is the latest firmware that I have tried: >> >> ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw >> 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 >> >> But still the same, firmware crashed: >> [ 154.920000] ath10k_pci 0000:00:00.0: failed to to request monitor >> vdev 1 stop: -11 >> [ 159.920000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >> vdev 1 stop: -145 >> [ 159.920000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >> [ 159.930000] ath10k_pci 0000:00:00.0: failed to recalc montior: -145 >> [ 162.940000] ath10k_pci 0000:00:00.0: failed to stop WMI vdev 0: -11 >> [ 165.940000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >> [ 168.940000] ath10k_pci 0000:00:00.0: failed to to request monitor >> vdev 1 stop: -11 >> [ 173.940000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >> vdev 1 stop: -145 >> [ 173.940000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >> [ 176.950000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >> [ 179.950000] ath10k_pci 0000:00:00.0: failed to to request monitor >> vdev 1 stop: -11 >> [ 184.950000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >> vdev 1 stop: -145 >> [ 184.950000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >> [ 187.960000] ath10k_pci 0000:00:00.0: failed to submit AP self-peer >> removal on vdev 0: -11 >> [ 190.960000] ath10k_pci 0000:00:00.0: failed to delete WMI vdev 0: -11 >> [ 193.960000] ath10k_pci 0000:00:00.0: failed to remove AP self-peer >> on vdev 0: -145 >> [ 193.960000] ath10k_pci 0000:00:00.0: removing stale peer >> 04:f0:21:0c:a5:17 from vdev_id 0 >> [ 196.970000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 > > Hmm.. Can you try to repack firmware and combine main binary from 10.2 > and otp from 10.1 and test that? You can use these tools: > > https://gist.github.com/kazikcz/64313b9e2470660faae1 > https://gist.github.com/kazikcz/c970cbf3a863ebbc4495 > > > Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-05-05 11:11 ` Yeoh Chun-Yeow @ 2015-05-05 11:19 ` Michal Kazior 2015-05-06 2:31 ` Yeoh Chun-Yeow 0 siblings, 1 reply; 17+ messages in thread From: Michal Kazior @ 2015-05-05 11:19 UTC (permalink / raw) To: Yeoh Chun-Yeow; +Cc: Kalle Valo, ath10k@lists.infradead.org On 5 May 2015 at 13:11, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: > What to be set for "VERSION_STRING DECIMAL_BITMASK_OF_FEATURES" for assembly? > > I ran into this error "IndexError: list index out of range" during assembly. I think the following should work: python assemble.py 10.2-test 12 fw-from-10.2.bin otp-from-10.1.bin 5 wmi-mgmt-tx = BIT(2) = 4 no-p2p = BIT(3) = 8 Hence `12` for features. If you assemble 10.2.4 wmi-op must be 5. If you use 10.2-00082 wmi-op must be 3. Michał > --- > Chun-Yeow > > On Tue, May 5, 2015 at 2:49 PM, Michal Kazior <michal.kazior@tieto.com> wrote: >> On 5 May 2015 at 07:56, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >>> Yes, this is the latest firmware that I have tried: >>> >>> ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw >>> 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 >>> >>> But still the same, firmware crashed: >>> [ 154.920000] ath10k_pci 0000:00:00.0: failed to to request monitor >>> vdev 1 stop: -11 >>> [ 159.920000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>> vdev 1 stop: -145 >>> [ 159.920000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>> [ 159.930000] ath10k_pci 0000:00:00.0: failed to recalc montior: -145 >>> [ 162.940000] ath10k_pci 0000:00:00.0: failed to stop WMI vdev 0: -11 >>> [ 165.940000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>> [ 168.940000] ath10k_pci 0000:00:00.0: failed to to request monitor >>> vdev 1 stop: -11 >>> [ 173.940000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>> vdev 1 stop: -145 >>> [ 173.940000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>> [ 176.950000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>> [ 179.950000] ath10k_pci 0000:00:00.0: failed to to request monitor >>> vdev 1 stop: -11 >>> [ 184.950000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>> vdev 1 stop: -145 >>> [ 184.950000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>> [ 187.960000] ath10k_pci 0000:00:00.0: failed to submit AP self-peer >>> removal on vdev 0: -11 >>> [ 190.960000] ath10k_pci 0000:00:00.0: failed to delete WMI vdev 0: -11 >>> [ 193.960000] ath10k_pci 0000:00:00.0: failed to remove AP self-peer >>> on vdev 0: -145 >>> [ 193.960000] ath10k_pci 0000:00:00.0: removing stale peer >>> 04:f0:21:0c:a5:17 from vdev_id 0 >>> [ 196.970000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >> >> Hmm.. Can you try to repack firmware and combine main binary from 10.2 >> and otp from 10.1 and test that? You can use these tools: >> >> https://gist.github.com/kazikcz/64313b9e2470660faae1 >> https://gist.github.com/kazikcz/c970cbf3a863ebbc4495 >> >> >> Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-05-05 11:19 ` Michal Kazior @ 2015-05-06 2:31 ` Yeoh Chun-Yeow 2015-05-06 5:41 ` Michal Kazior 0 siblings, 1 reply; 17+ messages in thread From: Yeoh Chun-Yeow @ 2015-05-06 2:31 UTC (permalink / raw) To: Michal Kazior; +Cc: Kalle Valo, ath10k@lists.infradead.org Not working as well, firmware crashed. [ 56.250000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw fw-10.2-otp-10.1 api 4 htt 2.1 wmi 5 cal otp max_sta 128 [ 56.260000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 dfs 1 testmode 1 [ 56.280000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100804: -16 [ 56.290000] ath10k_pci 0000:00:00.0: failed to get memcpy hi address for firmware address 4: -16 [ 56.300000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 [ 56.400000] ieee80211 phy0: Hardware restart was requested [ 56.400000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143 [ 56.410000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143 [ 56.420000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 [ 56.630000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 56.640000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 56.750000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 56.760000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 56.870000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 .... [ 138.740000] ath10k_pci 0000:00:00.0: failed to to request monitor vdev 1 stop: -143 [ 138.750000] ath10k_pci 0000:00:00.0: failed to synchronize monitor vdev 1 stop: -143 [ 138.760000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 [ 138.970000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 138.980000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 [ 139.090000] ath10k_pci 0000:00:00.0: failed to read diag value at 0x10100800: -16 [ 141.380000] ath10k_pci 0000:00:00.0: device successfully recovered [ 141.750000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid c95c836e-b4b3-40d6-bbac-d18eb4992b10) [ 141.760000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw fw-10.2-otp-10.1 api 4 htt 2.1 wmi 5 cal otp max_sta 128 ---- Chun-Yeow On Tue, May 5, 2015 at 7:19 PM, Michal Kazior <michal.kazior@tieto.com> wrote: > On 5 May 2015 at 13:11, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >> What to be set for "VERSION_STRING DECIMAL_BITMASK_OF_FEATURES" for assembly? >> >> I ran into this error "IndexError: list index out of range" during assembly. > > I think the following should work: > > python assemble.py 10.2-test 12 fw-from-10.2.bin otp-from-10.1.bin 5 > > wmi-mgmt-tx = BIT(2) = 4 > no-p2p = BIT(3) = 8 > > Hence `12` for features. > > If you assemble 10.2.4 wmi-op must be 5. If you use 10.2-00082 wmi-op must be 3. > > > Michał > > >> --- >> Chun-Yeow >> >> On Tue, May 5, 2015 at 2:49 PM, Michal Kazior <michal.kazior@tieto.com> wrote: >>> On 5 May 2015 at 07:56, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >>>> Yes, this is the latest firmware that I have tried: >>>> >>>> ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw >>>> 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 >>>> >>>> But still the same, firmware crashed: >>>> [ 154.920000] ath10k_pci 0000:00:00.0: failed to to request monitor >>>> vdev 1 stop: -11 >>>> [ 159.920000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>>> vdev 1 stop: -145 >>>> [ 159.920000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>>> [ 159.930000] ath10k_pci 0000:00:00.0: failed to recalc montior: -145 >>>> [ 162.940000] ath10k_pci 0000:00:00.0: failed to stop WMI vdev 0: -11 >>>> [ 165.940000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>>> [ 168.940000] ath10k_pci 0000:00:00.0: failed to to request monitor >>>> vdev 1 stop: -11 >>>> [ 173.940000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>>> vdev 1 stop: -145 >>>> [ 173.940000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>>> [ 176.950000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>>> [ 179.950000] ath10k_pci 0000:00:00.0: failed to to request monitor >>>> vdev 1 stop: -11 >>>> [ 184.950000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>>> vdev 1 stop: -145 >>>> [ 184.950000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>>> [ 187.960000] ath10k_pci 0000:00:00.0: failed to submit AP self-peer >>>> removal on vdev 0: -11 >>>> [ 190.960000] ath10k_pci 0000:00:00.0: failed to delete WMI vdev 0: -11 >>>> [ 193.960000] ath10k_pci 0000:00:00.0: failed to remove AP self-peer >>>> on vdev 0: -145 >>>> [ 193.960000] ath10k_pci 0000:00:00.0: removing stale peer >>>> 04:f0:21:0c:a5:17 from vdev_id 0 >>>> [ 196.970000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>> >>> Hmm.. Can you try to repack firmware and combine main binary from 10.2 >>> and otp from 10.1 and test that? You can use these tools: >>> >>> https://gist.github.com/kazikcz/64313b9e2470660faae1 >>> https://gist.github.com/kazikcz/c970cbf3a863ebbc4495 >>> >>> >>> Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-05-06 2:31 ` Yeoh Chun-Yeow @ 2015-05-06 5:41 ` Michal Kazior 2015-05-07 10:56 ` Yeoh Chun-Yeow 0 siblings, 1 reply; 17+ messages in thread From: Michal Kazior @ 2015-05-06 5:41 UTC (permalink / raw) To: Yeoh Chun-Yeow; +Cc: Kalle Valo, ath10k@lists.infradead.org On 6 May 2015 at 04:31, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: > Not working as well, firmware crashed. > > [ 56.250000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, > 0x043202ff) fw fw-10.2-otp-10.1 api 4 htt 2.1 wmi 5 cal otp max_sta > 128 > [ 56.260000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 > dfs 1 testmode 1 > [ 56.280000] ath10k_pci 0000:00:00.0: failed to read diag value at > 0x10100804: -16 > [ 56.290000] ath10k_pci 0000:00:00.0: failed to get memcpy hi > address for firmware address 4: -16 > [ 56.300000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 > [ 56.400000] ieee80211 phy0: Hardware restart was requested > [ 56.400000] ath10k_pci 0000:00:00.0: failed to to request monitor > vdev 1 stop: -143 > [ 56.410000] ath10k_pci 0000:00:00.0: failed to synchronize monitor > vdev 1 stop: -143 > [ 56.420000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 > [ 56.630000] ath10k_pci 0000:00:00.0: failed to read diag value at > 0x10100800: -16 > [ 56.640000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 > [ 56.750000] ath10k_pci 0000:00:00.0: failed to read diag value at > 0x10100800: -16 > [ 56.760000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 > [ 56.870000] ath10k_pci 0000:00:00.0: failed to read diag value at > 0x10100800: -16 > > .... > > [ 138.740000] ath10k_pci 0000:00:00.0: failed to to request monitor > vdev 1 stop: -143 > [ 138.750000] ath10k_pci 0000:00:00.0: failed to synchronize monitor > vdev 1 stop: -143 > [ 138.760000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 > [ 138.970000] ath10k_pci 0000:00:00.0: failed to read diag value at > 0x10100800: -16 > [ 138.980000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 > [ 139.090000] ath10k_pci 0000:00:00.0: failed to read diag value at > 0x10100800: -16 > [ 141.380000] ath10k_pci 0000:00:00.0: device successfully recovered > [ 141.750000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid > c95c836e-b4b3-40d6-bbac-d18eb4992b10) > [ 141.760000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, > 0x043202ff) fw fw-10.2-otp-10.1 api 4 htt 2.1 wmi 5 cal otp max_sta > 128 Thanks for checking. So the problem only happens with Compex WLE900N5-23 and other QCA988X's you have work fine with 10.2 - is that correct? Michał > ---- > Chun-Yeow > > On Tue, May 5, 2015 at 7:19 PM, Michal Kazior <michal.kazior@tieto.com> wrote: >> On 5 May 2015 at 13:11, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >>> What to be set for "VERSION_STRING DECIMAL_BITMASK_OF_FEATURES" for assembly? >>> >>> I ran into this error "IndexError: list index out of range" during assembly. >> >> I think the following should work: >> >> python assemble.py 10.2-test 12 fw-from-10.2.bin otp-from-10.1.bin 5 >> >> wmi-mgmt-tx = BIT(2) = 4 >> no-p2p = BIT(3) = 8 >> >> Hence `12` for features. >> >> If you assemble 10.2.4 wmi-op must be 5. If you use 10.2-00082 wmi-op must be 3. >> >> >> Michał >> >> >>> --- >>> Chun-Yeow >>> >>> On Tue, May 5, 2015 at 2:49 PM, Michal Kazior <michal.kazior@tieto.com> wrote: >>>> On 5 May 2015 at 07:56, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >>>>> Yes, this is the latest firmware that I have tried: >>>>> >>>>> ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw >>>>> 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 >>>>> >>>>> But still the same, firmware crashed: >>>>> [ 154.920000] ath10k_pci 0000:00:00.0: failed to to request monitor >>>>> vdev 1 stop: -11 >>>>> [ 159.920000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>>>> vdev 1 stop: -145 >>>>> [ 159.920000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>>>> [ 159.930000] ath10k_pci 0000:00:00.0: failed to recalc montior: -145 >>>>> [ 162.940000] ath10k_pci 0000:00:00.0: failed to stop WMI vdev 0: -11 >>>>> [ 165.940000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>>>> [ 168.940000] ath10k_pci 0000:00:00.0: failed to to request monitor >>>>> vdev 1 stop: -11 >>>>> [ 173.940000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>>>> vdev 1 stop: -145 >>>>> [ 173.940000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>>>> [ 176.950000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>>>> [ 179.950000] ath10k_pci 0000:00:00.0: failed to to request monitor >>>>> vdev 1 stop: -11 >>>>> [ 184.950000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>>>> vdev 1 stop: -145 >>>>> [ 184.950000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>>>> [ 187.960000] ath10k_pci 0000:00:00.0: failed to submit AP self-peer >>>>> removal on vdev 0: -11 >>>>> [ 190.960000] ath10k_pci 0000:00:00.0: failed to delete WMI vdev 0: -11 >>>>> [ 193.960000] ath10k_pci 0000:00:00.0: failed to remove AP self-peer >>>>> on vdev 0: -145 >>>>> [ 193.960000] ath10k_pci 0000:00:00.0: removing stale peer >>>>> 04:f0:21:0c:a5:17 from vdev_id 0 >>>>> [ 196.970000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>>> >>>> Hmm.. Can you try to repack firmware and combine main binary from 10.2 >>>> and otp from 10.1 and test that? You can use these tools: >>>> >>>> https://gist.github.com/kazikcz/64313b9e2470660faae1 >>>> https://gist.github.com/kazikcz/c970cbf3a863ebbc4495 >>>> >>>> >>>> Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: Compex WLE900N5-23 2015-05-06 5:41 ` Michal Kazior @ 2015-05-07 10:56 ` Yeoh Chun-Yeow 0 siblings, 0 replies; 17+ messages in thread From: Yeoh Chun-Yeow @ 2015-05-07 10:56 UTC (permalink / raw) To: Michal Kazior; +Cc: Kalle Valo, ath10k@lists.infradead.org I have also tested with Compex WLE900VX and 10.2 firmware also crashed in my embedded board. ---- Chun-Yeow On Wed, May 6, 2015 at 1:41 PM, Michal Kazior <michal.kazior@tieto.com> wrote: > On 6 May 2015 at 04:31, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >> Not working as well, firmware crashed. >> >> [ 56.250000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, >> 0x043202ff) fw fw-10.2-otp-10.1 api 4 htt 2.1 wmi 5 cal otp max_sta >> 128 >> [ 56.260000] ath10k_pci 0000:00:00.0: debug 1 debugfs 1 tracing 0 >> dfs 1 testmode 1 >> [ 56.280000] ath10k_pci 0000:00:00.0: failed to read diag value at >> 0x10100804: -16 >> [ 56.290000] ath10k_pci 0000:00:00.0: failed to get memcpy hi >> address for firmware address 4: -16 >> [ 56.300000] ath10k_pci 0000:00:00.0: failed to read firmware dump area: -16 >> [ 56.400000] ieee80211 phy0: Hardware restart was requested >> [ 56.400000] ath10k_pci 0000:00:00.0: failed to to request monitor >> vdev 1 stop: -143 >> [ 56.410000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >> vdev 1 stop: -143 >> [ 56.420000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 >> [ 56.630000] ath10k_pci 0000:00:00.0: failed to read diag value at >> 0x10100800: -16 >> [ 56.640000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 >> [ 56.750000] ath10k_pci 0000:00:00.0: failed to read diag value at >> 0x10100800: -16 >> [ 56.760000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 >> [ 56.870000] ath10k_pci 0000:00:00.0: failed to read diag value at >> 0x10100800: -16 >> >> .... >> >> [ 138.740000] ath10k_pci 0000:00:00.0: failed to to request monitor >> vdev 1 stop: -143 >> [ 138.750000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >> vdev 1 stop: -143 >> [ 138.760000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -143 >> [ 138.970000] ath10k_pci 0000:00:00.0: failed to read diag value at >> 0x10100800: -16 >> [ 138.980000] ath10k_pci 0000:00:00.0: failed to poke copy engine: -16 >> [ 139.090000] ath10k_pci 0000:00:00.0: failed to read diag value at >> 0x10100800: -16 >> [ 141.380000] ath10k_pci 0000:00:00.0: device successfully recovered >> [ 141.750000] ath10k_pci 0000:00:00.0: firmware crashed! (uuid >> c95c836e-b4b3-40d6-bbac-d18eb4992b10) >> [ 141.760000] ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, >> 0x043202ff) fw fw-10.2-otp-10.1 api 4 htt 2.1 wmi 5 cal otp max_sta >> 128 > > Thanks for checking. So the problem only happens with Compex > WLE900N5-23 and other QCA988X's you have work fine with 10.2 - is that > correct? > > > Michał > > >> ---- >> Chun-Yeow >> >> On Tue, May 5, 2015 at 7:19 PM, Michal Kazior <michal.kazior@tieto.com> wrote: >>> On 5 May 2015 at 13:11, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >>>> What to be set for "VERSION_STRING DECIMAL_BITMASK_OF_FEATURES" for assembly? >>>> >>>> I ran into this error "IndexError: list index out of range" during assembly. >>> >>> I think the following should work: >>> >>> python assemble.py 10.2-test 12 fw-from-10.2.bin otp-from-10.1.bin 5 >>> >>> wmi-mgmt-tx = BIT(2) = 4 >>> no-p2p = BIT(3) = 8 >>> >>> Hence `12` for features. >>> >>> If you assemble 10.2.4 wmi-op must be 5. If you use 10.2-00082 wmi-op must be 3. >>> >>> >>> Michał >>> >>> >>>> --- >>>> Chun-Yeow >>>> >>>> On Tue, May 5, 2015 at 2:49 PM, Michal Kazior <michal.kazior@tieto.com> wrote: >>>>> On 5 May 2015 at 07:56, Yeoh Chun-Yeow <yeohchunyeow@gmail.com> wrote: >>>>>> Yes, this is the latest firmware that I have tried: >>>>>> >>>>>> ath10k_pci 0000:00:00.0: qca988x hw2.0 (0x4100016c, 0x043202ff) fw >>>>>> 10.2.4.48 api 4 htt 2.1 wmi 5 cal otp max_sta 128 >>>>>> >>>>>> But still the same, firmware crashed: >>>>>> [ 154.920000] ath10k_pci 0000:00:00.0: failed to to request monitor >>>>>> vdev 1 stop: -11 >>>>>> [ 159.920000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>>>>> vdev 1 stop: -145 >>>>>> [ 159.920000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>>>>> [ 159.930000] ath10k_pci 0000:00:00.0: failed to recalc montior: -145 >>>>>> [ 162.940000] ath10k_pci 0000:00:00.0: failed to stop WMI vdev 0: -11 >>>>>> [ 165.940000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>>>>> [ 168.940000] ath10k_pci 0000:00:00.0: failed to to request monitor >>>>>> vdev 1 stop: -11 >>>>>> [ 173.940000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>>>>> vdev 1 stop: -145 >>>>>> [ 173.940000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>>>>> [ 176.950000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>>>>> [ 179.950000] ath10k_pci 0000:00:00.0: failed to to request monitor >>>>>> vdev 1 stop: -11 >>>>>> [ 184.950000] ath10k_pci 0000:00:00.0: failed to synchronize monitor >>>>>> vdev 1 stop: -145 >>>>>> [ 184.950000] ath10k_pci 0000:00:00.0: failed to stop monitor vdev: -145 >>>>>> [ 187.960000] ath10k_pci 0000:00:00.0: failed to submit AP self-peer >>>>>> removal on vdev 0: -11 >>>>>> [ 190.960000] ath10k_pci 0000:00:00.0: failed to delete WMI vdev 0: -11 >>>>>> [ 193.960000] ath10k_pci 0000:00:00.0: failed to remove AP self-peer >>>>>> on vdev 0: -145 >>>>>> [ 193.960000] ath10k_pci 0000:00:00.0: removing stale peer >>>>>> 04:f0:21:0c:a5:17 from vdev_id 0 >>>>>> [ 196.970000] ath10k_pci 0000:00:00.0: failed to put down monitor vdev 1: -11 >>>>> >>>>> Hmm.. Can you try to repack firmware and combine main binary from 10.2 >>>>> and otp from 10.1 and test that? You can use these tools: >>>>> >>>>> https://gist.github.com/kazikcz/64313b9e2470660faae1 >>>>> https://gist.github.com/kazikcz/c970cbf3a863ebbc4495 >>>>> >>>>> >>>>> Michał _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k ^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2015-05-07 10:56 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-04-30 2:29 Compex WLE900N5-23 Yeoh Chun-Yeow
2015-04-30 3:02 ` Kalle Valo
2015-04-30 4:27 ` Yeoh Chun-Yeow
2015-04-30 5:11 ` Michal Kazior
2015-04-30 6:46 ` Yeoh Chun-Yeow
2015-04-30 7:05 ` Michal Kazior
2015-04-30 10:31 ` Yeoh Chun-Yeow
2015-04-30 10:50 ` Michal Kazior
[not found] <CAEFj9871+uootjCDVNBEKSYiDJzdRcMLkWe=bKdmxKDKBCBbKA@mail.gmail.com>
2015-05-05 5:40 ` Yeoh Chun-Yeow
2015-05-05 5:47 ` Michal Kazior
2015-05-05 5:56 ` Yeoh Chun-Yeow
2015-05-05 6:49 ` Michal Kazior
2015-05-05 11:11 ` Yeoh Chun-Yeow
2015-05-05 11:19 ` Michal Kazior
2015-05-06 2:31 ` Yeoh Chun-Yeow
2015-05-06 5:41 ` Michal Kazior
2015-05-07 10:56 ` Yeoh Chun-Yeow
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox