[PATCH AUTOSEL 5.14 017/138] ath11k: Align bss_chan_info structure with firmware

[PATCH AUTOSEL 5.14 017/138] ath11k: Align bss_chan_info structure with firmware

[Sasha Levin]

From: Seevalamuthu Mariappan <seevalam@codeaurora.org>

[ Upstream commit feab5bb8f1d4621025dceae7eef62d5f92de34ac ]

pdev_id in structure 'wmi_pdev_bss_chan_info_event' is wrongly placed
at the beginning. This causes invalid values in survey dump. Hence, align
the structure with the firmware.

Note: The firmware releases follow this order since the feature was
implemented. Also, it is not changing across the branches including
QCA6390.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1

Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath11k/wmi.c | 1 +
 drivers/net/wireless/ath/ath11k/wmi.h | 3 ++-
 2 files changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/wireless/ath/ath11k/wmi.c b/drivers/net/wireless/ath/ath11k/wmi.c
index 6c253eae9d069..27c060dd3fb47 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.c
+++ b/drivers/net/wireless/ath/ath11k/wmi.c
@@ -1339,6 +1339,7 @@ int ath11k_wmi_pdev_bss_chan_info_request(struct ath11k *ar,
 				     WMI_TAG_PDEV_BSS_CHAN_INFO_REQUEST) |
 			  FIELD_PREP(WMI_TLV_LEN, sizeof(*cmd) - TLV_HDR_SIZE);
 	cmd->req_type = type;
+	cmd->pdev_id = ar->pdev->pdev_id;
 
 	ath11k_dbg(ar->ab, ATH11K_DBG_WMI,
 		   "WMI bss chan info req type %d\n", type);
diff --git a/drivers/net/wireless/ath/ath11k/wmi.h b/drivers/net/wireless/ath/ath11k/wmi.h
index d35c47e0b19d4..0b7d337b36930 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.h
+++ b/drivers/net/wireless/ath/ath11k/wmi.h
@@ -2960,6 +2960,7 @@ struct wmi_pdev_bss_chan_info_req_cmd {
 	u32 tlv_header;
 	/* ref wmi_bss_chan_info_req_type */
 	u32 req_type;
+	u32 pdev_id;
 } __packed;
 
 struct wmi_ap_ps_peer_cmd {
@@ -4056,7 +4057,6 @@ struct wmi_vdev_stopped_event {
 } __packed;
 
 struct wmi_pdev_bss_chan_info_event {
-	u32 pdev_id;
 	u32 freq;	/* Units in MHz */
 	u32 noise_floor;	/* units are dBm */
 	/* rx clear - how often the channel was unused */
@@ -4074,6 +4074,7 @@ struct wmi_pdev_bss_chan_info_event {
 	/*rx_cycle cnt for my bss in 64bits format */
 	u32 rx_bss_cycle_count_low;
 	u32 rx_bss_cycle_count_high;
+	u32 pdev_id;
 } __packed;
 
 #define WMI_VDEV_INSTALL_KEY_COMPL_STATUS_SUCCESS 0
-- 
2.33.0


-- 
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k

[PATCH AUTOSEL 5.14 030/138] ath11k: Avoid reg rules update during firmware recovery

[Sasha Levin]

From: Sriram R <srirrama@codeaurora.org>

[ Upstream commit 69a0fcf8a9f2273040d03e5ee77c9689c09e9d3a ]

During firmware recovery, the default reg rules which are
received via WMI_REG_CHAN_LIST_CC_EVENT can overwrite
the currently configured user regd.

See below snap for example,

root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI
country FR: DFS-ETSI

root@OpenWrt:/# echo assert > /sys/kernel/debug/ath11k/ipq8074\ hw2.0/simulate_f
w_crash
<snip>
[ 5290.471696] ath11k c000000.wifi1: pdev 1 successfully recovered

root@OpenWrt:/# iw reg get | grep country
country FR: DFS-ETSI
country US: DFS-FCC
country US: DFS-FCC
country US: DFS-FCC

In the above, the user configured country 'FR' is overwritten
when the rules of default country 'US' are received and updated during
recovery. Hence avoid processing of these rules in general
during firmware recovery as they have been already applied during
driver registration or after last set user country is configured.

This scenario applies for both AP and STA devices basically because
cfg80211 is not aware of the recovery and only the driver recovers, but
changing or resetting of the reg domain during recovery is not needed so
as to continue with the configured regdomain currently in use.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01460-QCAHKSWPL_SILICONZ-1

Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-3-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath11k/wmi.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/net/wireless/ath/ath11k/wmi.c b/drivers/net/wireless/ath/ath11k/wmi.c
index 27c060dd3fb47..fa27115483c6c 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.c
+++ b/drivers/net/wireless/ath/ath11k/wmi.c
@@ -5793,6 +5793,17 @@ static int ath11k_reg_chan_list_event(struct ath11k_base *ab, struct sk_buff *sk
 
 	pdev_idx = reg_info->phy_id;
 
+	/* Avoid default reg rule updates sent during FW recovery if
+	 * it is already available
+	 */
+	spin_lock(&ab->base_lock);
+	if (test_bit(ATH11K_FLAG_RECOVERY, &ab->dev_flags) &&
+	    ab->default_regd[pdev_idx]) {
+		spin_unlock(&ab->base_lock);
+		goto mem_free;
+	}
+	spin_unlock(&ab->base_lock);
+
 	if (pdev_idx >= ab->num_radios) {
 		/* Process the event for phy0 only if single_pdev_only
 		 * is true. If pdev_idx is valid but not 0, discard the
-- 
2.33.0


-- 
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k

[PATCH AUTOSEL 5.14 031/138] ath11k: add handler for scan event WMI_SCAN_EVENT_DEQUEUED

[Sasha Levin]

From: Wen Gong <wgong@codeaurora.org>

[ Upstream commit 441b3b5911f8ead7f2fe2336587b340a33044d58 ]

When wlan interface is up, 11d scan is sent to the firmware, and the
firmware needs to spend couple of seconds to complete the 11d scan. If
immediately a normal scan from user space arrives to ath11k, then the
normal scan request is also sent to the firmware, but the scan started
event will be reported to ath11k until the 11d scan complete. When timed
out for the scan started in ath11k, ath11k stops the normal scan and the
firmware reports WMI_SCAN_EVENT_DEQUEUED to ath11k for the normal scan.
ath11k has no handler for the event and then timed out for the scan
completed in ath11k_scan_stop(), and ath11k prints the following error
message.

[ 1491.604750] ath11k_pci 0000:02:00.0: failed to receive scan abort comple: timed out
[ 1491.604756] ath11k_pci 0000:02:00.0: failed to stop scan: -110
[ 1491.604758] ath11k_pci 0000:02:00.0: failed to start hw scan: -110

Add a handler for WMI_SCAN_EVENT_DEQUEUED and then complete the scan to
get rid of the above error message.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914164226.38843-1-jouni@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath11k/wmi.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/wireless/ath/ath11k/wmi.c b/drivers/net/wireless/ath/ath11k/wmi.c
index fa27115483c6c..72da1283f2ccb 100644
--- a/drivers/net/wireless/ath/ath11k/wmi.c
+++ b/drivers/net/wireless/ath/ath11k/wmi.c
@@ -6313,6 +6313,8 @@ static void ath11k_scan_event(struct ath11k_base *ab, struct sk_buff *skb)
 		ath11k_wmi_event_scan_start_failed(ar);
 		break;
 	case WMI_SCAN_EVENT_DEQUEUED:
+		__ath11k_mac_scan_finish(ar);
+		break;
 	case WMI_SCAN_EVENT_PREEMPTED:
 	case WMI_SCAN_EVENT_RESTARTED:
 	case WMI_SCAN_EVENT_FOREIGN_CHAN_EXIT:
-- 
2.33.0


-- 
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k

[PATCH AUTOSEL 5.14 032/138] ath11k: Change DMA_FROM_DEVICE to DMA_TO_DEVICE when map reinjected packets

[Sasha Levin]

From: Baochen Qiang <bqiang@codeaurora.org>

[ Upstream commit 86a03dad0f5ad8182ed5fcf7bf3eec71cd96577c ]

For fragmented packets, ath11k reassembles each fragment as a normal
packet and then reinjects it into HW ring. In this case, the DMA
direction should be DMA_TO_DEVICE, not DMA_FROM_DEVICE, otherwise
invalid payload will be reinjected to HW and then delivered to host.
What is more, since arbitrary memory could be allocated to the frame, we
don't know what kind of data is contained in the buffer reinjected.
Thus, as a bad result, private info may be leaked.

Note that this issue is only found on Intel platform.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916064617.20006-1-bqiang@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/ath/ath11k/dp_rx.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/ath11k/dp_rx.c b/drivers/net/wireless/ath/ath11k/dp_rx.c
index 603d2f93ac18f..d4f7304a35ec1 100644
--- a/drivers/net/wireless/ath/ath11k/dp_rx.c
+++ b/drivers/net/wireless/ath/ath11k/dp_rx.c
@@ -3315,7 +3315,7 @@ static int ath11k_dp_rx_h_defrag_reo_reinject(struct ath11k *ar, struct dp_rx_ti
 
 	paddr = dma_map_single(ab->dev, defrag_skb->data,
 			       defrag_skb->len + skb_tailroom(defrag_skb),
-			       DMA_FROM_DEVICE);
+			       DMA_TO_DEVICE);
 	if (dma_mapping_error(ab->dev, paddr))
 		return -ENOMEM;
 
@@ -3380,7 +3380,7 @@ static int ath11k_dp_rx_h_defrag_reo_reinject(struct ath11k *ar, struct dp_rx_ti
 	spin_unlock_bh(&rx_refill_ring->idr_lock);
 err_unmap_dma:
 	dma_unmap_single(ab->dev, paddr, defrag_skb->len + skb_tailroom(defrag_skb),
-			 DMA_FROM_DEVICE);
+			 DMA_TO_DEVICE);
 	return ret;
 }
 
-- 
2.33.0


-- 
ath11k mailing list
ath11k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath11k