[PATCH ath-next V15 0/9] wifi: ath12k: add MU-MIMO and 160 MHz bandwidth support

[PATCH ath-next V15 0/9] wifi: ath12k: add MU-MIMO and 160 MHz bandwidth support

[Pradeep Kumar Chitrapu]

  Add support for
1. enabling MU-MIMO in HE and EHT modes from hardware
2. setting fixed HE rate/GI/LTF
3. 160 MHz bandwidth in HE mode
4. extended NSS bandwidth support

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3

changes in v15:
 - rebased the series after merge conflicts reported
 patch 4/9:
 - change the fix to apply for all modes except STA mode as
   WCN7850 expect it same as before.

changes in v14:
 patch 6/9:
 - cap max_nss using ar->num_tx_chains to fix interop issue caused due
   to sending nss value 4 when firmware only supports nss value 2.
 patch 8/9:
 - Set the default return value to MODE_11AC_VHT160 for 160 MHz
   to allow STA to connect to the AP even if it does not
   explicitly indicate 160 MHz bandwidth support.

changes in v13:
 - rebase

changes in v12:
 - rebase

changes in v11:
 patch 1/9:
  - fix return values in ath12k_mac_set_he_txbf_conf() and
    ath12k_mac_vif_recalc_sta_he_txbf()
 patch 6/9:
  - fix missing he_mcs initialization in ath12k_mac_init_arvif()

changes in v10:
 patch 6/9:
  - use ath12k_ahsta_to_sta()
  - fix rcu_dereference warning in ath12k_mac_set_bitrate_mask_iter()
  - change return type for ath12k_mac_validate_fixed_rate_settings()
  - improve readability by adhering to nl80211 definitions of GI
    NL80211_TXRATE_DEFAULT_GI. Introduce ath12k_mac_nlgi_to_wmigi()
    for conversion.
 patch 7/9:
  - do not change default MODE_11AC_VHT160 in
    ath12k_mac_get_phymode_vht() as it breaks clients which do not
    set VHT_CAP_SUPP_CHAN_WIDTH_160MHZ.
 patch 8/9:
  - Use IEEE80211_VHT_CAP_EXT_NSS_BW_MASK along with
    IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ for determining VHT160
    phymode.

changes in v9: rebase on top of master branch with mlo changes
 patch 1/9 and 2/9:
  - fetch link_conf using ath12k_mac_get_link_bss_conf()
    instead of arvif->vif->bss_conf before mlo
 patch 6/9
  - fetch mcs/nss values from sta->link[] instead of sta->deflink
  - fix spelling of 'incompatibility'
 patch 8/9
  - replace sta->deflink.addr with arsta->addr in
    ath12k_peer_assoc_h_vht
 patch 9/9
  - replace sta->deflink.rx_nss with link_sta->rx_nss

changes in v8:
 - rebase and resolve KASAN warnings reported by Jeff in v7, in patch 6/9.

Pradeep Kumar Chitrapu (9):
  wifi: ath12k: push HE MU-MIMO params to hardware
  wifi: ath12k: push EHT MU-MIMO params to hardware
  wifi: ath12k: move HE MCS mapper to a separate function
  wifi: ath12k: generate rx and tx mcs maps for supported HE mcs
  wifi: ath12k: fix TX and RX MCS rate configurations in HE mode
  wifi: ath12k: add support for setting fixed HE rate/GI/LTF
  wifi: ath12k: clean up 80P80 support
  wifi: ath12k: add support for 160 MHz bandwidth
  wifi: ath12k: add extended NSS bandwidth support for 160 MHz

 drivers/net/wireless/ath/ath12k/core.h |    2 +
 drivers/net/wireless/ath/ath12k/mac.c  | 1144 ++++++++++++++++++++----
 drivers/net/wireless/ath/ath12k/mac.h  |   17 +
 drivers/net/wireless/ath/ath12k/wmi.c  |   28 +-
 drivers/net/wireless/ath/ath12k/wmi.h  |  100 ++-
 5 files changed, 1069 insertions(+), 222 deletions(-)


base-commit: c256a94d1b1b15109740306f7f2a7c2173e12072
-- 
2.43.0

[PATCH ath-next V15 1/9] wifi: ath12k: push HE MU-MIMO params to hardware

[Pradeep Kumar Chitrapu]

Currently, only the HE IE in management frames is updated with
respect to MU-MIMO configurations, but this change is not
reflected in the hardware. Add support to propagate MU-MIMO
configurations to the hardware as well.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Co-developed-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 228 +++++++++++++++++---------
 drivers/net/wireless/ath/ath12k/mac.h |  15 ++
 drivers/net/wireless/ath/ath12k/wmi.h |  28 +---
 3 files changed, 169 insertions(+), 102 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 71e07c546a2d..c81cecb01c06 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -3160,6 +3160,125 @@ static int ath12k_setup_peer_smps(struct ath12k *ar, struct ath12k_link_vif *arv
 					 ath12k_smps_map[smps]);
 }
 
+static int ath12k_mac_set_he_txbf_conf(struct ath12k_link_vif *arvif)
+{
+	struct ath12k_vif *ahvif = arvif->ahvif;
+	struct ath12k *ar = arvif->ar;
+	u32 param = WMI_VDEV_PARAM_SET_HEMU_MODE;
+	u32 value = 0;
+	int ret;
+	struct ieee80211_bss_conf *link_conf;
+
+	link_conf = ath12k_mac_get_link_bss_conf(arvif);
+	if (!link_conf) {
+		ath12k_warn(ar->ab, "unable to access bss link conf in txbf conf\n");
+		return -EINVAL;
+	}
+
+	if (!link_conf->he_support)
+		return 0;
+
+	if (link_conf->he_su_beamformer) {
+		value |= u32_encode_bits(HE_SU_BFER_ENABLE, HE_MODE_SU_TX_BFER);
+		if (link_conf->he_mu_beamformer &&
+		    ahvif->vdev_type == WMI_VDEV_TYPE_AP)
+			value |= u32_encode_bits(HE_MU_BFER_ENABLE, HE_MODE_MU_TX_BFER);
+	}
+
+	if (ahvif->vif->type != NL80211_IFTYPE_MESH_POINT) {
+		value |= u32_encode_bits(HE_DL_MUOFDMA_ENABLE, HE_MODE_DL_OFDMA) |
+			 u32_encode_bits(HE_UL_MUOFDMA_ENABLE, HE_MODE_UL_OFDMA);
+
+		if (link_conf->he_full_ul_mumimo)
+			value |= u32_encode_bits(HE_UL_MUMIMO_ENABLE, HE_MODE_UL_MUMIMO);
+
+		if (link_conf->he_su_beamformee)
+			value |= u32_encode_bits(HE_SU_BFEE_ENABLE, HE_MODE_SU_TX_BFEE);
+	}
+
+	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id, param, value);
+	if (ret) {
+		ath12k_warn(ar->ab, "failed to set vdev %d HE MU mode: %d\n",
+			    arvif->vdev_id, ret);
+		return ret;
+	}
+
+	param = WMI_VDEV_PARAM_SET_HE_SOUNDING_MODE;
+	value =	u32_encode_bits(HE_VHT_SOUNDING_MODE_ENABLE, HE_VHT_SOUNDING_MODE) |
+		u32_encode_bits(HE_TRIG_NONTRIG_SOUNDING_MODE_ENABLE,
+				HE_TRIG_NONTRIG_SOUNDING_MODE);
+	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
+					    param, value);
+	if (ret) {
+		ath12k_warn(ar->ab, "failed to set vdev %d sounding mode: %d\n",
+			    arvif->vdev_id, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int ath12k_mac_vif_recalc_sta_he_txbf(struct ath12k *ar,
+					     struct ath12k_link_vif *arvif,
+					     struct ieee80211_sta_he_cap *he_cap,
+					     int *hemode)
+{
+	struct ieee80211_vif *vif = arvif->ahvif->vif;
+	struct ieee80211_he_cap_elem he_cap_elem = {};
+	struct ieee80211_sta_he_cap *cap_band;
+	struct cfg80211_chan_def def;
+	u8 link_id = arvif->link_id;
+	struct ieee80211_bss_conf *link_conf;
+
+	link_conf = ath12k_mac_get_link_bss_conf(arvif);
+	if (!link_conf) {
+		ath12k_warn(ar->ab, "unable to access bss link conf in recalc txbf conf\n");
+		return -EINVAL;
+	}
+
+	if (!link_conf->he_support)
+		return 0;
+
+	if (vif->type != NL80211_IFTYPE_STATION)
+		return -EINVAL;
+
+	if (WARN_ON(ath12k_mac_vif_link_chan(vif, link_id, &def)))
+		return -EINVAL;
+
+	if (def.chan->band == NL80211_BAND_2GHZ)
+		cap_band = &ar->mac.iftype[NL80211_BAND_2GHZ][vif->type].he_cap;
+	else
+		cap_band = &ar->mac.iftype[NL80211_BAND_5GHZ][vif->type].he_cap;
+
+	memcpy(&he_cap_elem, &cap_band->he_cap_elem, sizeof(he_cap_elem));
+
+	*hemode = 0;
+	if (HECAP_PHY_SUBFME_GET(he_cap_elem.phy_cap_info)) {
+		if (HECAP_PHY_SUBFMR_GET(he_cap->he_cap_elem.phy_cap_info))
+			*hemode |= u32_encode_bits(HE_SU_BFEE_ENABLE, HE_MODE_SU_TX_BFEE);
+		if (HECAP_PHY_MUBFMR_GET(he_cap->he_cap_elem.phy_cap_info))
+			*hemode |= u32_encode_bits(HE_MU_BFEE_ENABLE, HE_MODE_MU_TX_BFEE);
+	}
+
+	if (vif->type != NL80211_IFTYPE_MESH_POINT) {
+		*hemode |= u32_encode_bits(HE_DL_MUOFDMA_ENABLE, HE_MODE_DL_OFDMA) |
+			  u32_encode_bits(HE_UL_MUOFDMA_ENABLE, HE_MODE_UL_OFDMA);
+
+		if (HECAP_PHY_ULMUMIMO_GET(he_cap_elem.phy_cap_info))
+			if (HECAP_PHY_ULMUMIMO_GET(he_cap->he_cap_elem.phy_cap_info))
+				*hemode |= u32_encode_bits(HE_UL_MUMIMO_ENABLE,
+							  HE_MODE_UL_MUMIMO);
+
+		if (u32_get_bits(*hemode, HE_MODE_MU_TX_BFEE))
+			*hemode |= u32_encode_bits(HE_SU_BFEE_ENABLE, HE_MODE_SU_TX_BFEE);
+
+		if (u32_get_bits(*hemode, HE_MODE_MU_TX_BFER))
+			*hemode |= u32_encode_bits(HE_SU_BFER_ENABLE, HE_MODE_SU_TX_BFER);
+	}
+
+	return 0;
+}
+
 static u32 ath12k_mac_ieee80211_sta_bw_to_wmi(struct ath12k *ar,
 					      struct ieee80211_link_sta *link_sta)
 {
@@ -3205,6 +3324,7 @@ static void ath12k_bss_assoc(struct ath12k *ar,
 	struct ath12k_sta *ahsta;
 	struct ath12k_peer *peer;
 	bool is_auth = false;
+	u32 hemode = 0;
 	int ret;
 
 	lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
@@ -3248,8 +3368,26 @@ static void ath12k_bss_assoc(struct ath12k *ar,
 
 	ath12k_peer_assoc_prepare(ar, arvif, arsta, peer_arg, false);
 
+	/* link_sta->he_cap must be protected by rcu_read_lock */
+	ret = ath12k_mac_vif_recalc_sta_he_txbf(ar, arvif, &link_sta->he_cap, &hemode);
+	if (ret) {
+		ath12k_warn(ar->ab, "failed to recalc he txbf for vdev %i on bss %pM: %d\n",
+			    arvif->vdev_id, bss_conf->bssid, ret);
+		rcu_read_unlock();
+		return;
+	}
+
 	rcu_read_unlock();
 
+	/* keep this before ath12k_wmi_send_peer_assoc_cmd() */
+	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
+					    WMI_VDEV_PARAM_SET_HEMU_MODE, hemode);
+	if (ret) {
+		ath12k_warn(ar->ab, "failed to submit vdev param txbf 0x%x: %d\n",
+			    hemode, ret);
+		return;
+	}
+
 	peer_arg->is_assoc = true;
 	ret = ath12k_wmi_send_peer_assoc_cmd(ar, peer_arg);
 	if (ret) {
@@ -3874,6 +4012,13 @@ static void ath12k_mac_bss_info_changed(struct ath12k *ar,
 		ether_addr_copy(arvif->bssid, info->bssid);
 
 	if (changed & BSS_CHANGED_BEACON_ENABLED) {
+		if (info->enable_beacon) {
+			ret = ath12k_mac_set_he_txbf_conf(arvif);
+			if (ret)
+				ath12k_warn(ar->ab,
+					    "failed to set HE TXBF config for vdev: %d\n",
+					    arvif->vdev_id);
+		}
 		ath12k_control_beaconing(arvif, info);
 
 		if (arvif->is_up && info->he_support &&
@@ -7349,11 +7494,14 @@ static void ath12k_mac_copy_he_cap(struct ath12k_band_cap *band_cap,
 
 	he_cap_elem->mac_cap_info[1] &=
 		IEEE80211_HE_MAC_CAP1_TF_MAC_PAD_DUR_MASK;
-
+	he_cap_elem->phy_cap_info[0] &=
+		IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_IN_2G |
+		IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G |
+		IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G;
+	he_cap_elem->phy_cap_info[0] &=
+		~IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G;
 	he_cap_elem->phy_cap_info[5] &=
 		~IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_UNDER_80MHZ_MASK;
-	he_cap_elem->phy_cap_info[5] &=
-		~IEEE80211_HE_PHY_CAP5_BEAMFORMEE_NUM_SND_DIM_ABOVE_80MHZ_MASK;
 	he_cap_elem->phy_cap_info[5] |= num_tx_chains - 1;
 
 	switch (iftype) {
@@ -8672,72 +8820,6 @@ static int ath12k_mac_setup_vdev_create_arg(struct ath12k_link_vif *arvif,
 	return 0;
 }
 
-static u32
-ath12k_mac_prepare_he_mode(struct ath12k_pdev *pdev, u32 viftype)
-{
-	struct ath12k_pdev_cap *pdev_cap = &pdev->cap;
-	struct ath12k_band_cap *cap_band = NULL;
-	u32 *hecap_phy_ptr = NULL;
-	u32 hemode;
-
-	if (pdev->cap.supported_bands & WMI_HOST_WLAN_2GHZ_CAP)
-		cap_band = &pdev_cap->band[NL80211_BAND_2GHZ];
-	else
-		cap_band = &pdev_cap->band[NL80211_BAND_5GHZ];
-
-	hecap_phy_ptr = &cap_band->he_cap_phy_info[0];
-
-	hemode = u32_encode_bits(HE_SU_BFEE_ENABLE, HE_MODE_SU_TX_BFEE) |
-		 u32_encode_bits(HECAP_PHY_SUBFMR_GET(hecap_phy_ptr),
-				 HE_MODE_SU_TX_BFER) |
-		 u32_encode_bits(HECAP_PHY_ULMUMIMO_GET(hecap_phy_ptr),
-				 HE_MODE_UL_MUMIMO);
-
-	/* TODO: WDS and other modes */
-	if (viftype == NL80211_IFTYPE_AP) {
-		hemode |= u32_encode_bits(HECAP_PHY_MUBFMR_GET(hecap_phy_ptr),
-					  HE_MODE_MU_TX_BFER) |
-			  u32_encode_bits(HE_DL_MUOFDMA_ENABLE, HE_MODE_DL_OFDMA) |
-			  u32_encode_bits(HE_UL_MUOFDMA_ENABLE, HE_MODE_UL_OFDMA);
-	} else {
-		hemode |= u32_encode_bits(HE_MU_BFEE_ENABLE, HE_MODE_MU_TX_BFEE);
-	}
-
-	return hemode;
-}
-
-static int ath12k_set_he_mu_sounding_mode(struct ath12k *ar,
-					  struct ath12k_link_vif *arvif)
-{
-	u32 param_id, param_value;
-	struct ath12k_base *ab = ar->ab;
-	struct ath12k_vif *ahvif = arvif->ahvif;
-	int ret;
-
-	param_id = WMI_VDEV_PARAM_SET_HEMU_MODE;
-	param_value = ath12k_mac_prepare_he_mode(ar->pdev, ahvif->vif->type);
-	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
-					    param_id, param_value);
-	if (ret) {
-		ath12k_warn(ab, "failed to set vdev %d HE MU mode: %d param_value %x\n",
-			    arvif->vdev_id, ret, param_value);
-		return ret;
-	}
-	param_id = WMI_VDEV_PARAM_SET_HE_SOUNDING_MODE;
-	param_value =
-		u32_encode_bits(HE_VHT_SOUNDING_MODE_ENABLE, HE_VHT_SOUNDING_MODE) |
-		u32_encode_bits(HE_TRIG_NONTRIG_SOUNDING_MODE_ENABLE,
-				HE_TRIG_NONTRIG_SOUNDING_MODE);
-	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
-					    param_id, param_value);
-	if (ret) {
-		ath12k_warn(ab, "failed to set vdev %d HE MU mode: %d\n",
-			    arvif->vdev_id, ret);
-		return ret;
-	}
-	return ret;
-}
-
 static void ath12k_mac_update_vif_offload(struct ath12k_link_vif *arvif)
 {
 	struct ath12k_vif *ahvif = arvif->ahvif;
@@ -9931,14 +10013,6 @@ ath12k_mac_vdev_start_restart(struct ath12k_link_vif *arvif,
 		spin_unlock_bh(&ab->base_lock);
 
 		/* TODO: Notify if secondary 80Mhz also needs radar detection */
-		if (link_conf->he_support) {
-			ret = ath12k_set_he_mu_sounding_mode(ar, arvif);
-			if (ret) {
-				ath12k_warn(ar->ab, "failed to set he mode vdev %i\n",
-					    arg.vdev_id);
-				return ret;
-			}
-		}
 	}
 
 	arg.passive |= !!(chandef->chan->flags & IEEE80211_CHAN_NO_IR);
diff --git a/drivers/net/wireless/ath/ath12k/mac.h b/drivers/net/wireless/ath/ath12k/mac.h
index 473611bfccdc..9241afe7dc02 100644
--- a/drivers/net/wireless/ath/ath12k/mac.h
+++ b/drivers/net/wireless/ath/ath12k/mac.h
@@ -59,6 +59,21 @@ struct ath12k_generic_iter {
 
 #define ATH12K_NUM_MAX_ACTIVE_LINKS_PER_DEVICE	2
 
+#define HECAP_PHY_SUBFMR_GET(hecap_phy) \
+	u8_get_bits(hecap_phy[3], IEEE80211_HE_PHY_CAP3_SU_BEAMFORMER)
+
+#define HECAP_PHY_SUBFME_GET(hecap_phy) \
+	u8_get_bits(hecap_phy[4], IEEE80211_HE_PHY_CAP4_SU_BEAMFORMEE)
+
+#define HECAP_PHY_MUBFMR_GET(hecap_phy) \
+	u8_get_bits(hecap_phy[4], IEEE80211_HE_PHY_CAP4_MU_BEAMFORMER)
+
+#define HECAP_PHY_ULMUMIMO_GET(hecap_phy) \
+	u8_get_bits(hecap_phy[2], IEEE80211_HE_PHY_CAP2_UL_MU_FULL_MU_MIMO)
+
+#define HECAP_PHY_ULOFDMA_GET(hecap_phy) \
+	u8_get_bits(hecap_phy[2], IEEE80211_HE_PHY_CAP2_UL_MU_PARTIAL_MU_MIMO)
+
 enum ath12k_supported_bw {
 	ATH12K_BW_20    = 0,
 	ATH12K_BW_40    = 1,
diff --git a/drivers/net/wireless/ath/ath12k/wmi.h b/drivers/net/wireless/ath/ath12k/wmi.h
index ccf430164717..07cba3997e75 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.h
+++ b/drivers/net/wireless/ath/ath12k/wmi.h
@@ -3136,31 +3136,6 @@ struct ath12k_wmi_rx_reorder_queue_remove_arg {
 #define WMI_VDEV_PARAM_TXBF_SU_TX_BFER BIT(2)
 #define WMI_VDEV_PARAM_TXBF_MU_TX_BFER BIT(3)
 
-#define HECAP_PHYDWORD_0	0
-#define HECAP_PHYDWORD_1	1
-#define HECAP_PHYDWORD_2	2
-
-#define HECAP_PHY_SU_BFER		BIT(31)
-#define HECAP_PHY_SU_BFEE		BIT(0)
-#define HECAP_PHY_MU_BFER		BIT(1)
-#define HECAP_PHY_UL_MUMIMO		BIT(22)
-#define HECAP_PHY_UL_MUOFDMA		BIT(23)
-
-#define HECAP_PHY_SUBFMR_GET(hecap_phy) \
-	u32_get_bits(hecap_phy[HECAP_PHYDWORD_0], HECAP_PHY_SU_BFER)
-
-#define HECAP_PHY_SUBFME_GET(hecap_phy) \
-	u32_get_bits(hecap_phy[HECAP_PHYDWORD_1], HECAP_PHY_SU_BFEE)
-
-#define HECAP_PHY_MUBFMR_GET(hecap_phy) \
-	u32_get_bits(hecap_phy[HECAP_PHYDWORD_1], HECAP_PHY_MU_BFER)
-
-#define HECAP_PHY_ULMUMIMO_GET(hecap_phy) \
-	u32_get_bits(hecap_phy[HECAP_PHYDWORD_0], HECAP_PHY_UL_MUMIMO)
-
-#define HECAP_PHY_ULOFDMA_GET(hecap_phy) \
-	u32_get_bits(hecap_phy[HECAP_PHYDWORD_0], HECAP_PHY_UL_MUOFDMA)
-
 #define HE_MODE_SU_TX_BFEE	BIT(0)
 #define HE_MODE_SU_TX_BFER	BIT(1)
 #define HE_MODE_MU_TX_BFEE	BIT(2)
@@ -3172,8 +3147,11 @@ struct ath12k_wmi_rx_reorder_queue_remove_arg {
 #define HE_DL_MUOFDMA_ENABLE	1
 #define HE_UL_MUOFDMA_ENABLE	1
 #define HE_DL_MUMIMO_ENABLE	1
+#define HE_UL_MUMIMO_ENABLE	1
 #define HE_MU_BFEE_ENABLE	1
 #define HE_SU_BFEE_ENABLE	1
+#define HE_MU_BFER_ENABLE	1
+#define HE_SU_BFER_ENABLE	1
 
 #define HE_VHT_SOUNDING_MODE_ENABLE		1
 #define HE_SU_MU_SOUNDING_MODE_ENABLE		1
-- 
2.43.0

[PATCH ath-next V15 2/9] wifi: ath12k: push EHT MU-MIMO params to hardware

[Pradeep Kumar Chitrapu]

Currently, only the EHT IE in management frames is updated with
respect to MU-MIMO configurations, but this change is not
reflected in the hardware. Add support to propagate MU-MIMO
configurations to the hardware as well for AP mode. Similar
support for STA mode will be added in future.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Co-developed-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 58 +++++++++++++++++++++++++++
 drivers/net/wireless/ath/ath12k/wmi.h | 21 ++++++++++
 2 files changed, 79 insertions(+)

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index c81cecb01c06..811b44c703b4 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -3279,6 +3279,58 @@ static int ath12k_mac_vif_recalc_sta_he_txbf(struct ath12k *ar,
 	return 0;
 }
 
+static int ath12k_mac_set_eht_txbf_conf(struct ath12k_link_vif *arvif)
+{
+	struct ath12k_vif *ahvif = arvif->ahvif;
+	struct ath12k *ar = arvif->ar;
+	u32 param = WMI_VDEV_PARAM_SET_EHT_MU_MODE;
+	u32 value = 0;
+	int ret;
+	struct ieee80211_bss_conf *link_conf;
+
+	link_conf = ath12k_mac_get_link_bss_conf(arvif);
+	if (!link_conf) {
+		ath12k_warn(ar->ab, "unable to access bss link conf in eht txbf conf\n");
+		return -ENOENT;
+	}
+
+	if (!link_conf->eht_support)
+		return 0;
+
+	if (link_conf->eht_su_beamformer) {
+		value |= u32_encode_bits(EHT_SU_BFER_ENABLE, EHT_MODE_SU_TX_BFER);
+		if (link_conf->eht_mu_beamformer &&
+		    ahvif->vdev_type == WMI_VDEV_TYPE_AP)
+			value |= u32_encode_bits(EHT_MU_BFER_ENABLE,
+						 EHT_MODE_MU_TX_BFER) |
+				 u32_encode_bits(EHT_DL_MUOFDMA_ENABLE,
+						 EHT_MODE_DL_OFDMA_MUMIMO) |
+				 u32_encode_bits(EHT_UL_MUOFDMA_ENABLE,
+						 EHT_MODE_UL_OFDMA_MUMIMO);
+	}
+
+	if (ahvif->vif->type != NL80211_IFTYPE_MESH_POINT) {
+		value |= u32_encode_bits(EHT_DL_MUOFDMA_ENABLE, EHT_MODE_DL_OFDMA) |
+			 u32_encode_bits(EHT_UL_MUOFDMA_ENABLE, EHT_MODE_UL_OFDMA);
+
+		if (link_conf->eht_80mhz_full_bw_ul_mumimo)
+			value |= u32_encode_bits(EHT_UL_MUMIMO_ENABLE, EHT_MODE_MUMIMO);
+
+		if (link_conf->eht_su_beamformee)
+			value |= u32_encode_bits(EHT_SU_BFEE_ENABLE,
+						 EHT_MODE_SU_TX_BFEE);
+	}
+
+	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id, param, value);
+	if (ret) {
+		ath12k_warn(ar->ab, "failed to set vdev %d EHT MU mode: %d\n",
+			    arvif->vdev_id, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
 static u32 ath12k_mac_ieee80211_sta_bw_to_wmi(struct ath12k *ar,
 					      struct ieee80211_link_sta *link_sta)
 {
@@ -4018,6 +4070,12 @@ static void ath12k_mac_bss_info_changed(struct ath12k *ar,
 				ath12k_warn(ar->ab,
 					    "failed to set HE TXBF config for vdev: %d\n",
 					    arvif->vdev_id);
+
+			ret = ath12k_mac_set_eht_txbf_conf(arvif);
+			if (ret)
+				ath12k_warn(ar->ab,
+					    "failed to set EHT TXBF config for vdev: %d\n",
+					    arvif->vdev_id);
 		}
 		ath12k_control_beaconing(arvif, info);
 
diff --git a/drivers/net/wireless/ath/ath12k/wmi.h b/drivers/net/wireless/ath/ath12k/wmi.h
index 07cba3997e75..0964ca03069a 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.h
+++ b/drivers/net/wireless/ath/ath12k/wmi.h
@@ -1178,6 +1178,7 @@ enum wmi_tlv_vdev_param {
 	WMI_VDEV_PARAM_BSS_COLOR,
 	WMI_VDEV_PARAM_SET_HEMU_MODE,
 	WMI_VDEV_PARAM_HEOPS_0_31 = 0x8003,
+	WMI_VDEV_PARAM_SET_EHT_MU_MODE = 0x8005,
 };
 
 enum wmi_tlv_peer_flags {
@@ -3153,6 +3154,26 @@ struct ath12k_wmi_rx_reorder_queue_remove_arg {
 #define HE_MU_BFER_ENABLE	1
 #define HE_SU_BFER_ENABLE	1
 
+#define EHT_MODE_SU_TX_BFEE		BIT(0)
+#define EHT_MODE_SU_TX_BFER		BIT(1)
+#define EHT_MODE_MU_TX_BFEE		BIT(2)
+#define EHT_MODE_MU_TX_BFER		BIT(3)
+#define EHT_MODE_DL_OFDMA		BIT(4)
+#define EHT_MODE_UL_OFDMA		BIT(5)
+#define EHT_MODE_MUMIMO			BIT(6)
+#define EHT_MODE_DL_OFDMA_TXBF		BIT(7)
+#define EHT_MODE_DL_OFDMA_MUMIMO	BIT(8)
+#define EHT_MODE_UL_OFDMA_MUMIMO	BIT(9)
+
+#define EHT_DL_MUOFDMA_ENABLE    1
+#define EHT_UL_MUOFDMA_ENABLE    1
+#define EHT_DL_MUMIMO_ENABLE     1
+#define EHT_UL_MUMIMO_ENABLE     1
+#define EHT_MU_BFEE_ENABLE       1
+#define EHT_SU_BFEE_ENABLE       1
+#define EHT_MU_BFER_ENABLE       1
+#define EHT_SU_BFER_ENABLE       1
+
 #define HE_VHT_SOUNDING_MODE_ENABLE		1
 #define HE_SU_MU_SOUNDING_MODE_ENABLE		1
 #define HE_TRIG_NONTRIG_SOUNDING_MODE_ENABLE	1
-- 
2.43.0

[PATCH ath-next V15 3/9] wifi: ath12k: move HE MCS mapper to a separate function

[Pradeep Kumar Chitrapu]

Refactor the HE MCS mapper functionality in
ath12k_mac_copy_he_cap() into a new function.

This helps improve readability, extensibility and will be used
when adding support for 160 MHz bandwidth in subsequent patches.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Co-developed-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 22 ++++++++++++++--------
 1 file changed, 14 insertions(+), 8 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 811b44c703b4..f3833fa08070 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -7537,12 +7537,24 @@ static __le16 ath12k_mac_setup_he_6ghz_cap(struct ath12k_pdev_cap *pcap,
 	return cpu_to_le16(bcap->he_6ghz_capa);
 }
 
+static void ath12k_mac_set_hemcsmap(struct ath12k_band_cap *band_cap,
+				    struct ieee80211_sta_he_cap *he_cap)
+{
+	struct ieee80211_he_mcs_nss_supp *mcs_nss = &he_cap->he_mcs_nss_supp;
+
+	mcs_nss->rx_mcs_80 = cpu_to_le16(band_cap->he_mcs & 0xffff);
+	mcs_nss->tx_mcs_80 = cpu_to_le16(band_cap->he_mcs & 0xffff);
+	mcs_nss->rx_mcs_160 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
+	mcs_nss->tx_mcs_160 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
+	mcs_nss->rx_mcs_80p80 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
+	mcs_nss->tx_mcs_80p80 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
+}
+
 static void ath12k_mac_copy_he_cap(struct ath12k_band_cap *band_cap,
 				   int iftype, u8 num_tx_chains,
 				   struct ieee80211_sta_he_cap *he_cap)
 {
 	struct ieee80211_he_cap_elem *he_cap_elem = &he_cap->he_cap_elem;
-	struct ieee80211_he_mcs_nss_supp *mcs_nss = &he_cap->he_mcs_nss_supp;
 
 	he_cap->has_he = true;
 	memcpy(he_cap_elem->mac_cap_info, band_cap->he_cap_info,
@@ -7582,13 +7594,7 @@ static void ath12k_mac_copy_he_cap(struct ath12k_band_cap *band_cap,
 		break;
 	}
 
-	mcs_nss->rx_mcs_80 = cpu_to_le16(band_cap->he_mcs & 0xffff);
-	mcs_nss->tx_mcs_80 = cpu_to_le16(band_cap->he_mcs & 0xffff);
-	mcs_nss->rx_mcs_160 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
-	mcs_nss->tx_mcs_160 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
-	mcs_nss->rx_mcs_80p80 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
-	mcs_nss->tx_mcs_80p80 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
-
+	ath12k_mac_set_hemcsmap(band_cap, he_cap);
 	memset(he_cap->ppe_thres, 0, sizeof(he_cap->ppe_thres));
 	if (he_cap_elem->phy_cap_info[6] &
 	    IEEE80211_HE_PHY_CAP6_PPE_THRESHOLD_PRESENT)
-- 
2.43.0

[PATCH ath-next V15 4/9] wifi: ath12k: generate rx and tx mcs maps for supported HE mcs

[Pradeep Kumar Chitrapu]

Generate rx and tx mcs maps in ath12k_mac_set_hemcsmap() based
on number of supported tx/rx chains and set them in supported
mcs/nss for HE capabilities.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Co-developed-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 40 ++++++++++++++++++++-------
 1 file changed, 30 insertions(+), 10 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index f3833fa08070..37f50851a236 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -7537,20 +7537,40 @@ static __le16 ath12k_mac_setup_he_6ghz_cap(struct ath12k_pdev_cap *pcap,
 	return cpu_to_le16(bcap->he_6ghz_capa);
 }
 
-static void ath12k_mac_set_hemcsmap(struct ath12k_band_cap *band_cap,
+static void ath12k_mac_set_hemcsmap(struct ath12k *ar,
+				    struct ath12k_pdev_cap *cap,
 				    struct ieee80211_sta_he_cap *he_cap)
 {
 	struct ieee80211_he_mcs_nss_supp *mcs_nss = &he_cap->he_mcs_nss_supp;
+	u16 txmcs_map, rxmcs_map;
+	u32 i;
+
+	rxmcs_map = 0;
+	txmcs_map = 0;
+	for (i = 0; i < 8; i++) {
+		if (i < ar->num_tx_chains &&
+		    (ar->cfg_tx_chainmask >> cap->tx_chain_mask_shift) & BIT(i))
+			txmcs_map |= IEEE80211_HE_MCS_SUPPORT_0_11 << (i * 2);
+		else
+			txmcs_map |= IEEE80211_HE_MCS_NOT_SUPPORTED << (i * 2);
+
+		if (i < ar->num_rx_chains &&
+		    (ar->cfg_rx_chainmask >> cap->tx_chain_mask_shift) & BIT(i))
+			rxmcs_map |= IEEE80211_HE_MCS_SUPPORT_0_11 << (i * 2);
+		else
+			rxmcs_map |= IEEE80211_HE_MCS_NOT_SUPPORTED << (i * 2);
+	}
 
-	mcs_nss->rx_mcs_80 = cpu_to_le16(band_cap->he_mcs & 0xffff);
-	mcs_nss->tx_mcs_80 = cpu_to_le16(band_cap->he_mcs & 0xffff);
-	mcs_nss->rx_mcs_160 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
-	mcs_nss->tx_mcs_160 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
-	mcs_nss->rx_mcs_80p80 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
-	mcs_nss->tx_mcs_80p80 = cpu_to_le16((band_cap->he_mcs >> 16) & 0xffff);
+	mcs_nss->rx_mcs_80 = cpu_to_le16(rxmcs_map & 0xffff);
+	mcs_nss->tx_mcs_80 = cpu_to_le16(txmcs_map & 0xffff);
+	mcs_nss->rx_mcs_160 = cpu_to_le16(rxmcs_map & 0xffff);
+	mcs_nss->tx_mcs_160 = cpu_to_le16(txmcs_map & 0xffff);
+	mcs_nss->rx_mcs_80p80 = cpu_to_le16(rxmcs_map & 0xffff);
+	mcs_nss->tx_mcs_80p80 = cpu_to_le16(txmcs_map & 0xffff);
 }
 
-static void ath12k_mac_copy_he_cap(struct ath12k_band_cap *band_cap,
+static void ath12k_mac_copy_he_cap(struct ath12k *ar,
+				   struct ath12k_band_cap *band_cap,
 				   int iftype, u8 num_tx_chains,
 				   struct ieee80211_sta_he_cap *he_cap)
 {
@@ -7594,7 +7614,7 @@ static void ath12k_mac_copy_he_cap(struct ath12k_band_cap *band_cap,
 		break;
 	}
 
-	ath12k_mac_set_hemcsmap(band_cap, he_cap);
+	ath12k_mac_set_hemcsmap(ar, &ar->pdev->cap, he_cap);
 	memset(he_cap->ppe_thres, 0, sizeof(he_cap->ppe_thres));
 	if (he_cap_elem->phy_cap_info[6] &
 	    IEEE80211_HE_PHY_CAP6_PPE_THRESHOLD_PRESENT)
@@ -7784,7 +7804,7 @@ static int ath12k_mac_copy_sband_iftype_data(struct ath12k *ar,
 
 		data[idx].types_mask = BIT(i);
 
-		ath12k_mac_copy_he_cap(band_cap, i, ar->num_tx_chains, he_cap);
+		ath12k_mac_copy_he_cap(ar, band_cap, i, ar->num_tx_chains, he_cap);
 		if (band == NL80211_BAND_6GHZ) {
 			data[idx].he_6ghz_capa.capa =
 				ath12k_mac_setup_he_6ghz_cap(cap, band_cap);
-- 
2.43.0

[PATCH ath-next V15 5/9] wifi: ath12k: fix TX and RX MCS rate configurations in HE mode

[Pradeep Kumar Chitrapu]

Currently, the TX and RX MCS rate configurations per peer are
reversed when sent to the firmware. As a result, RX MCS rates
are configured for TX, and vice versa. This commit rectifies
the configuration to match what the firmware expects.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/wmi.c | 19 +++++++++++++++++--
 drivers/net/wireless/ath/ath12k/wmi.h |  2 ++
 2 files changed, 19 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/wmi.c b/drivers/net/wireless/ath/ath12k/wmi.c
index 6c6354b3e18e..cdf3406302ee 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.c
+++ b/drivers/net/wireless/ath/ath12k/wmi.c
@@ -2183,6 +2183,8 @@ int ath12k_wmi_send_peer_assoc_cmd(struct ath12k *ar,
 				   struct ath12k_wmi_peer_assoc_arg *arg)
 {
 	struct ath12k_wmi_pdev *wmi = ar->wmi;
+	struct ath12k_base *ab = ar->ab;
+	struct ath12k_link_vif *arvif;
 	struct wmi_peer_assoc_complete_cmd *cmd;
 	struct ath12k_wmi_vht_rate_set_params *mcs;
 	struct ath12k_wmi_he_rate_set_params *he_mcs;
@@ -2198,6 +2200,13 @@ int ath12k_wmi_send_peer_assoc_cmd(struct ath12k *ar,
 	u16 eml_cap;
 	__le32 v;
 
+	arvif = ath12k_mac_get_arvif(ar, arg->vdev_id);
+	if (!arvif) {
+		ath12k_warn(ab, "failed to find arvif with vdev id %d\n",
+			    arg->vdev_id);
+		return -EINVAL;
+	}
+
 	peer_legacy_rates_align = roundup(arg->peer_legacy_rates.num_rates,
 					  sizeof(u32));
 	peer_ht_rates_align = roundup(arg->peer_ht_rates.num_rates,
@@ -2333,8 +2342,14 @@ int ath12k_wmi_send_peer_assoc_cmd(struct ath12k *ar,
 		he_mcs->tlv_header = ath12k_wmi_tlv_cmd_hdr(WMI_TAG_HE_RATE_SET,
 							    sizeof(*he_mcs));
 
-		he_mcs->rx_mcs_set = cpu_to_le32(arg->peer_he_rx_mcs_set[i]);
-		he_mcs->tx_mcs_set = cpu_to_le32(arg->peer_he_tx_mcs_set[i]);
+		if (arvif->ahvif->vdev_type == WMI_VDEV_TYPE_STA) {
+			he_mcs->rx_mcs_set = cpu_to_le32(arg->peer_he_rx_mcs_set[i]);
+			he_mcs->tx_mcs_set = cpu_to_le32(arg->peer_he_tx_mcs_set[i]);
+
+		} else {
+			he_mcs->rx_mcs_set = cpu_to_le32(arg->peer_he_tx_mcs_set[i]);
+			he_mcs->tx_mcs_set = cpu_to_le32(arg->peer_he_rx_mcs_set[i]);
+		}
 		ptr += sizeof(*he_mcs);
 	}
 
diff --git a/drivers/net/wireless/ath/ath12k/wmi.h b/drivers/net/wireless/ath/ath12k/wmi.h
index 0964ca03069a..7ad84624600d 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.h
+++ b/drivers/net/wireless/ath/ath12k/wmi.h
@@ -4162,7 +4162,9 @@ struct ath12k_wmi_vht_rate_set_params {
 
 struct ath12k_wmi_he_rate_set_params {
 	__le32 tlv_header;
+	/* MCS at which the peer can receive */
 	__le32 rx_mcs_set;
+	/* MCS at which the peer can transmit */
 	__le32 tx_mcs_set;
 } __packed;
 
-- 
2.43.0

[PATCH ath-next V15 6/9] wifi: ath12k: add support for setting fixed HE rate/GI/LTF

[Pradeep Kumar Chitrapu]

Add support to set fixed HE rate/GI/LTF values using nl80211.
Reuse parts of the existing code path already used for HT/VHT
to implement the new helpers symmetrically, similar to how
HT/VHT is handled.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Co-developed-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 650 +++++++++++++++++++++++---
 drivers/net/wireless/ath/ath12k/wmi.h |  27 ++
 2 files changed, 625 insertions(+), 52 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 37f50851a236..aefb620b28e2 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -521,6 +521,18 @@ ath12k_mac_max_vht_nss(const u16 *vht_mcs_mask)
 	return 1;
 }
 
+static u32
+ath12k_mac_max_he_nss(const u16 he_mcs_mask[NL80211_HE_NSS_MAX])
+{
+	int nss;
+
+	for (nss = NL80211_HE_NSS_MAX - 1; nss >= 0; nss--)
+		if (he_mcs_mask[nss])
+			return nss + 1;
+
+	return 1;
+}
+
 static u8 ath12k_parse_mpdudensity(u8 mpdudensity)
 {
 /*  From IEEE Std 802.11-2020 defined values for "Minimum MPDU Start Spacing":
@@ -2071,9 +2083,15 @@ static void ath12k_peer_assoc_h_ht(struct ath12k *ar,
 		arg->peer_rate_caps |= WMI_HOST_RC_CW40_FLAG;
 	}
 
-	if (arvif->bitrate_mask.control[band].gi != NL80211_TXRATE_FORCE_LGI) {
-		if (ht_cap->cap & (IEEE80211_HT_CAP_SGI_20 |
-		    IEEE80211_HT_CAP_SGI_40))
+	/* As firmware handles these two flags (IEEE80211_HT_CAP_SGI_20
+	 * and IEEE80211_HT_CAP_SGI_40) for enabling SGI, reset both
+	 * flags if guard interval is to force Long GI
+	 */
+	if (arvif->bitrate_mask.control[band].gi == NL80211_TXRATE_FORCE_LGI) {
+		arg->peer_ht_caps &= ~(IEEE80211_HT_CAP_SGI_20 | IEEE80211_HT_CAP_SGI_40);
+	} else {
+		/* Enable SGI flag if either SGI_20 or SGI_40 is supported */
+		if (ht_cap->cap & (IEEE80211_HT_CAP_SGI_20 | IEEE80211_HT_CAP_SGI_40))
 			arg->peer_rate_caps |= WMI_HOST_RC_SGI_FLAG;
 	}
 
@@ -2196,11 +2214,12 @@ static void ath12k_peer_assoc_h_vht(struct ath12k *ar,
 	struct ieee80211_link_sta *link_sta;
 	struct cfg80211_chan_def def;
 	enum nl80211_band band;
-	const u16 *vht_mcs_mask;
+	u16 *vht_mcs_mask;
 	u16 tx_mcs_map;
 	u8 ampdu_factor;
 	u8 max_nss, vht_mcs;
-	int i;
+	int i, vht_nss, nss_idx;
+	bool user_rate_valid = true;
 
 	lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
 
@@ -2253,6 +2272,25 @@ static void ath12k_peer_assoc_h_vht(struct ath12k *ar,
 	if (link_sta->bandwidth == IEEE80211_STA_RX_BW_160)
 		arg->bw_160 = true;
 
+	vht_nss =  ath12k_mac_max_vht_nss(vht_mcs_mask);
+
+	if (vht_nss > link_sta->rx_nss) {
+		user_rate_valid = false;
+		for (nss_idx = link_sta->rx_nss - 1; nss_idx >= 0; nss_idx--) {
+			if (vht_mcs_mask[nss_idx]) {
+				user_rate_valid = true;
+				break;
+			}
+		}
+	}
+
+	if (!user_rate_valid) {
+		ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
+			   "Setting vht range MCS value to peer supported nss:%d for peer %pM\n",
+			   link_sta->rx_nss, arsta->addr);
+		vht_mcs_mask[link_sta->rx_nss - 1] = vht_mcs_mask[vht_nss - 1];
+	}
+
 	/* Calculate peer NSS capability from VHT capabilities if STA
 	 * supports VHT.
 	 */
@@ -2292,6 +2330,72 @@ static void ath12k_peer_assoc_h_vht(struct ath12k *ar,
 	/* TODO: rxnss_override */
 }
 
+static int ath12k_mac_get_max_he_mcs_map(u16 mcs_map, int nss)
+{
+	switch ((mcs_map >> (2 * nss)) & 0x3) {
+	case IEEE80211_HE_MCS_SUPPORT_0_7: return BIT(8) - 1;
+	case IEEE80211_HE_MCS_SUPPORT_0_9: return BIT(10) - 1;
+	case IEEE80211_HE_MCS_SUPPORT_0_11: return BIT(12) - 1;
+	}
+	return 0;
+}
+
+static u16 ath12k_peer_assoc_h_he_limit(u16 tx_mcs_set,
+					const u16 *he_mcs_limit)
+{
+	int idx_limit;
+	int nss;
+	u16 mcs_map;
+	u16 mcs;
+
+	for (nss = 0; nss < NL80211_HE_NSS_MAX; nss++) {
+		mcs_map = ath12k_mac_get_max_he_mcs_map(tx_mcs_set, nss) &
+			he_mcs_limit[nss];
+
+		if (mcs_map)
+			idx_limit = fls(mcs_map) - 1;
+		else
+			idx_limit = -1;
+
+		switch (idx_limit) {
+		case 0 ... 7:
+			mcs = IEEE80211_HE_MCS_SUPPORT_0_7;
+			break;
+		case 8:
+		case 9:
+			mcs = IEEE80211_HE_MCS_SUPPORT_0_9;
+			break;
+		case 10:
+		case 11:
+			mcs = IEEE80211_HE_MCS_SUPPORT_0_11;
+			break;
+		default:
+			WARN_ON(1);
+			fallthrough;
+		case -1:
+			mcs = IEEE80211_HE_MCS_NOT_SUPPORTED;
+			break;
+		}
+
+		tx_mcs_set &= ~(0x3 << (nss * 2));
+		tx_mcs_set |= mcs << (nss * 2);
+	}
+
+	return tx_mcs_set;
+}
+
+static bool
+ath12k_peer_assoc_h_he_masked(const u16 he_mcs_mask[NL80211_HE_NSS_MAX])
+{
+	int nss;
+
+	for (nss = 0; nss < NL80211_HE_NSS_MAX; nss++)
+		if (he_mcs_mask[nss])
+			return false;
+
+	return true;
+}
+
 static void ath12k_peer_assoc_h_he(struct ath12k *ar,
 				   struct ath12k_link_vif *arvif,
 				   struct ath12k_link_sta *arsta,
@@ -2302,18 +2406,28 @@ static void ath12k_peer_assoc_h_he(struct ath12k *ar,
 	const struct ieee80211_sta_he_cap *he_cap;
 	struct ieee80211_bss_conf *link_conf;
 	struct ieee80211_link_sta *link_sta;
+	struct cfg80211_chan_def def;
 	int i;
 	u8 ampdu_factor, max_nss;
 	u8 rx_mcs_80 = IEEE80211_HE_MCS_NOT_SUPPORTED;
 	u8 rx_mcs_160 = IEEE80211_HE_MCS_NOT_SUPPORTED;
 	u16 mcs_160_map, mcs_80_map;
+	u8 link_id = arvif->link_id;
 	bool support_160;
-	u16 v;
+	enum nl80211_band band;
+	u16 *he_mcs_mask;
+	u8 he_mcs;
+	u16 he_tx_mcs = 0, v = 0;
+	int he_nss, nss_idx;
+	bool user_rate_valid = true;
+
+	if (WARN_ON(ath12k_mac_vif_link_chan(vif, link_id, &def)))
+		return;
 
 	link_conf = ath12k_mac_get_link_bss_conf(arvif);
 	if (!link_conf) {
 		ath12k_warn(ar->ab, "unable to access bss link conf in peer assoc he for vif %pM link %u",
-			    vif->addr, arvif->link_id);
+			    vif->addr, link_id);
 		return;
 	}
 
@@ -2328,6 +2442,12 @@ static void ath12k_peer_assoc_h_he(struct ath12k *ar,
 	if (!he_cap->has_he)
 		return;
 
+	band = def.chan->band;
+	he_mcs_mask = arvif->bitrate_mask.control[band].he_mcs;
+
+	if (ath12k_peer_assoc_h_he_masked(he_mcs_mask))
+		return;
+
 	arg->he_flag = true;
 
 	support_160 = !!(he_cap->he_cap_elem.phy_cap_info[0] &
@@ -2433,25 +2553,47 @@ static void ath12k_peer_assoc_h_he(struct ath12k *ar,
 	if (he_cap->he_cap_elem.mac_cap_info[0] & IEEE80211_HE_MAC_CAP0_TWT_REQ)
 		arg->twt_requester = true;
 
+	he_nss = ath12k_mac_max_he_nss(he_mcs_mask);
+
+	if (he_nss > link_sta->rx_nss) {
+		user_rate_valid = false;
+		for (nss_idx = link_sta->rx_nss - 1; nss_idx >= 0; nss_idx--) {
+			if (he_mcs_mask[nss_idx]) {
+				user_rate_valid = true;
+				break;
+			}
+		}
+	}
+
+	if (!user_rate_valid) {
+		ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
+			   "Setting he range MCS value to peer supported nss:%d for peer %pM\n",
+			   link_sta->rx_nss, arsta->addr);
+		he_mcs_mask[link_sta->rx_nss - 1] = he_mcs_mask[he_nss - 1];
+	}
+
 	switch (link_sta->bandwidth) {
 	case IEEE80211_STA_RX_BW_160:
 		if (he_cap->he_cap_elem.phy_cap_info[0] &
 		    IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G) {
-			v = le16_to_cpu(he_cap->he_mcs_nss_supp.rx_mcs_80p80);
+			v = ath12k_peer_assoc_h_he_limit(v, he_mcs_mask);
 			arg->peer_he_rx_mcs_set[WMI_HECAP_TXRX_MCS_NSS_IDX_80_80] = v;
 
 			v = le16_to_cpu(he_cap->he_mcs_nss_supp.tx_mcs_80p80);
 			arg->peer_he_tx_mcs_set[WMI_HECAP_TXRX_MCS_NSS_IDX_80_80] = v;
 
 			arg->peer_he_mcs_count++;
+			he_tx_mcs = v;
 		}
 		v = le16_to_cpu(he_cap->he_mcs_nss_supp.rx_mcs_160);
 		arg->peer_he_rx_mcs_set[WMI_HECAP_TXRX_MCS_NSS_IDX_160] = v;
 
-		v = le16_to_cpu(he_cap->he_mcs_nss_supp.tx_mcs_160);
+		v = ath12k_peer_assoc_h_he_limit(v, he_mcs_mask);
 		arg->peer_he_tx_mcs_set[WMI_HECAP_TXRX_MCS_NSS_IDX_160] = v;
 
 		arg->peer_he_mcs_count++;
+		if (!he_tx_mcs)
+			he_tx_mcs = v;
 		fallthrough;
 
 	default:
@@ -2459,11 +2601,36 @@ static void ath12k_peer_assoc_h_he(struct ath12k *ar,
 		arg->peer_he_rx_mcs_set[WMI_HECAP_TXRX_MCS_NSS_IDX_80] = v;
 
 		v = le16_to_cpu(he_cap->he_mcs_nss_supp.tx_mcs_80);
+		v = ath12k_peer_assoc_h_he_limit(v, he_mcs_mask);
 		arg->peer_he_tx_mcs_set[WMI_HECAP_TXRX_MCS_NSS_IDX_80] = v;
 
 		arg->peer_he_mcs_count++;
+		if (!he_tx_mcs)
+			he_tx_mcs = v;
 		break;
 	}
+
+	/* Calculate peer NSS capability from HE capabilities if STA
+	 * supports HE.
+	 */
+	for (i = 0, max_nss = 0, he_mcs = 0; i < NL80211_HE_NSS_MAX; i++) {
+		he_mcs = he_tx_mcs >> (2 * i) & 3;
+
+		/* In case of fixed rates, MCS Range in he_tx_mcs might have
+		 * unsupported range, with he_mcs_mask set, so check either of them
+		 * to find nss.
+		 */
+		if (he_mcs != IEEE80211_HE_MCS_NOT_SUPPORTED ||
+		    he_mcs_mask[i])
+			max_nss = i + 1;
+	}
+
+	max_nss = min(max_nss, ar->num_tx_chains);
+	arg->peer_nss = min(link_sta->rx_nss, max_nss);
+
+	ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
+		   "mac he peer %pM nss %d mcs cnt %d\n",
+		   arsta->addr, arg->peer_nss, arg->peer_he_mcs_count);
 }
 
 static void ath12k_peer_assoc_h_he_6ghz(struct ath12k *ar,
@@ -2799,6 +2966,7 @@ static void ath12k_peer_assoc_h_phymode(struct ath12k *ar,
 	enum nl80211_band band;
 	const u8 *ht_mcs_mask;
 	const u16 *vht_mcs_mask;
+	const u16 *he_mcs_mask;
 	enum wmi_phy_mode phymode = MODE_UNKNOWN;
 
 	lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
@@ -2812,6 +2980,7 @@ static void ath12k_peer_assoc_h_phymode(struct ath12k *ar,
 	band = def.chan->band;
 	ht_mcs_mask = arvif->bitrate_mask.control[band].ht_mcs;
 	vht_mcs_mask = arvif->bitrate_mask.control[band].vht_mcs;
+	he_mcs_mask = arvif->bitrate_mask.control[band].he_mcs;
 
 	link_sta = ath12k_mac_get_link_sta(arsta);
 	if (!link_sta) {
@@ -2827,7 +2996,8 @@ static void ath12k_peer_assoc_h_phymode(struct ath12k *ar,
 				phymode = MODE_11BE_EHT40_2G;
 			else
 				phymode = MODE_11BE_EHT20_2G;
-		} else if (link_sta->he_cap.has_he) {
+		} else if (link_sta->he_cap.has_he &&
+			   !ath12k_peer_assoc_h_he_masked(he_mcs_mask)) {
 			if (link_sta->bandwidth == IEEE80211_STA_RX_BW_80)
 				phymode = MODE_11AX_HE80_2G;
 			else if (link_sta->bandwidth == IEEE80211_STA_RX_BW_40)
@@ -2857,7 +3027,8 @@ static void ath12k_peer_assoc_h_phymode(struct ath12k *ar,
 		/* Check EHT first */
 		if (link_sta->eht_cap.has_eht) {
 			phymode = ath12k_mac_get_phymode_eht(ar, link_sta);
-		} else if (link_sta->he_cap.has_he) {
+		} else if (link_sta->he_cap.has_he &&
+			   !ath12k_peer_assoc_h_he_masked(he_mcs_mask)) {
 			phymode = ath12k_mac_get_phymode_he(ar, link_sta);
 		} else if (link_sta->vht_cap.vht_supported &&
 		    !ath12k_peer_assoc_h_vht_masked(vht_mcs_mask)) {
@@ -3647,10 +3818,13 @@ static void ath12k_mac_init_arvif(struct ath12k_vif *ahvif,
 
 	for (i = 0; i < ARRAY_SIZE(arvif->bitrate_mask.control); i++) {
 		arvif->bitrate_mask.control[i].legacy = 0xffffffff;
+		arvif->bitrate_mask.control[i].gi = NL80211_TXRATE_DEFAULT_GI;
 		memset(arvif->bitrate_mask.control[i].ht_mcs, 0xff,
 		       sizeof(arvif->bitrate_mask.control[i].ht_mcs));
 		memset(arvif->bitrate_mask.control[i].vht_mcs, 0xff,
 		       sizeof(arvif->bitrate_mask.control[i].vht_mcs));
+		memset(arvif->bitrate_mask.control[i].he_mcs, 0xff,
+		       sizeof(arvif->bitrate_mask.control[i].he_mcs));
 	}
 
 	/* Handle MLO related assignments */
@@ -5474,6 +5648,20 @@ ath12k_mac_bitrate_mask_num_vht_rates(struct ath12k *ar,
 	return num_rates;
 }
 
+static int
+ath12k_mac_bitrate_mask_num_he_rates(struct ath12k *ar,
+				     enum nl80211_band band,
+				     const struct cfg80211_bitrate_mask *mask)
+{
+	int num_rates = 0;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(mask->control[band].he_mcs); i++)
+		num_rates += hweight16(mask->control[band].he_mcs[i]);
+
+	return num_rates;
+}
+
 static int
 ath12k_mac_set_peer_vht_fixed_rate(struct ath12k_link_vif *arvif,
 				   struct ath12k_link_sta *arsta,
@@ -5520,6 +5708,60 @@ ath12k_mac_set_peer_vht_fixed_rate(struct ath12k_link_vif *arvif,
 	return ret;
 }
 
+static int
+ath12k_mac_set_peer_he_fixed_rate(struct ath12k_link_vif *arvif,
+				  struct ath12k_link_sta *arsta,
+				  const struct cfg80211_bitrate_mask *mask,
+				  enum nl80211_band band)
+{
+	struct ath12k *ar = arvif->ar;
+	u8 he_rate, nss;
+	u32 rate_code;
+	int ret, i;
+	struct ath12k_sta *ahsta = arsta->ahsta;
+	struct ieee80211_sta *sta;
+
+	lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
+
+	sta = ath12k_ahsta_to_sta(ahsta);
+	nss = 0;
+
+	for (i = 0; i < ARRAY_SIZE(mask->control[band].he_mcs); i++) {
+		if (hweight16(mask->control[band].he_mcs[i]) == 1) {
+			nss = i + 1;
+			he_rate = ffs(mask->control[band].he_mcs[i]) - 1;
+		}
+	}
+
+	if (!nss) {
+		ath12k_warn(ar->ab, "No single HE Fixed rate found to set for %pM",
+			    arsta->addr);
+		return -EINVAL;
+	}
+
+	/* Avoid updating invalid nss as fixed rate*/
+	if (nss > sta->deflink.rx_nss)
+		return -EINVAL;
+
+	ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
+		   "Setting Fixed HE Rate for peer %pM. Device will not switch to any other selected rates",
+		   arsta->addr);
+
+	rate_code = ATH12K_HW_RATE_CODE(he_rate, nss - 1,
+					WMI_RATE_PREAMBLE_HE);
+
+	ret = ath12k_wmi_set_peer_param(ar, arsta->addr,
+					arvif->vdev_id,
+					WMI_PEER_PARAM_FIXED_RATE,
+					rate_code);
+	if (ret)
+		ath12k_warn(ar->ab,
+			    "failed to update STA %pM Fixed Rate %d: %d\n",
+			    arsta->addr, rate_code, ret);
+
+	return ret;
+}
+
 static int ath12k_mac_station_assoc(struct ath12k *ar,
 				    struct ath12k_link_vif *arvif,
 				    struct ath12k_link_sta *arsta,
@@ -5532,7 +5774,7 @@ static int ath12k_mac_station_assoc(struct ath12k *ar,
 	struct cfg80211_chan_def def;
 	enum nl80211_band band;
 	struct cfg80211_bitrate_mask *mask;
-	u8 num_vht_rates;
+	u8 num_vht_rates, num_he_rates;
 	u8 link_id = arvif->link_id;
 
 	lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
@@ -5574,9 +5816,10 @@ static int ath12k_mac_station_assoc(struct ath12k *ar,
 	}
 
 	num_vht_rates = ath12k_mac_bitrate_mask_num_vht_rates(ar, band, mask);
+	num_he_rates = ath12k_mac_bitrate_mask_num_he_rates(ar, band, mask);
 
-	/* If single VHT rate is configured (by set_bitrate_mask()),
-	 * peer_assoc will disable VHT. This is now enabled by a peer specific
+	/* If single VHT/HE rate is configured (by set_bitrate_mask()),
+	 * peer_assoc will disable VHT/HE. This is now enabled by a peer specific
 	 * fixed param.
 	 * Note that all other rates and NSS will be disabled for this peer.
 	 */
@@ -5592,8 +5835,9 @@ static int ath12k_mac_station_assoc(struct ath12k *ar,
 	spin_unlock_bh(&ar->data_lock);
 
 	if (link_sta->vht_cap.vht_supported && num_vht_rates == 1) {
-		ret = ath12k_mac_set_peer_vht_fixed_rate(arvif, arsta, mask,
-							 band);
+		ret = ath12k_mac_set_peer_vht_fixed_rate(arvif, arsta, mask, band);
+	} else if (link_sta->he_cap.has_he && num_he_rates == 1) {
+		ret = ath12k_mac_set_peer_he_fixed_rate(arvif, arsta, mask, band);
 		if (ret)
 			return ret;
 	}
@@ -5657,8 +5901,9 @@ static void ath12k_sta_rc_update_wk(struct wiphy *wiphy, struct wiphy_work *wk)
 	enum nl80211_band band;
 	const u8 *ht_mcs_mask;
 	const u16 *vht_mcs_mask;
-	u32 changed, bw, nss, smps, bw_prev;
-	int err, num_vht_rates;
+	const u16 *he_mcs_mask;
+	u32 changed, bw, nss, mac_nss, smps, bw_prev;
+	int err, num_vht_rates, num_he_rates;
 	const struct cfg80211_bitrate_mask *mask;
 	enum wmi_phy_mode peer_phymode;
 	struct ath12k_link_sta *arsta;
@@ -5678,6 +5923,7 @@ static void ath12k_sta_rc_update_wk(struct wiphy *wiphy, struct wiphy_work *wk)
 	band = def.chan->band;
 	ht_mcs_mask = arvif->bitrate_mask.control[band].ht_mcs;
 	vht_mcs_mask = arvif->bitrate_mask.control[band].vht_mcs;
+	he_mcs_mask = arvif->bitrate_mask.control[band].he_mcs;
 
 	spin_lock_bh(&ar->data_lock);
 
@@ -5692,8 +5938,10 @@ static void ath12k_sta_rc_update_wk(struct wiphy *wiphy, struct wiphy_work *wk)
 	spin_unlock_bh(&ar->data_lock);
 
 	nss = max_t(u32, 1, nss);
-	nss = min(nss, max(ath12k_mac_max_ht_nss(ht_mcs_mask),
-			   ath12k_mac_max_vht_nss(vht_mcs_mask)));
+	mac_nss = max3(ath12k_mac_max_ht_nss(ht_mcs_mask),
+		       ath12k_mac_max_vht_nss(vht_mcs_mask),
+		       ath12k_mac_max_he_nss(he_mcs_mask));
+	nss = min(nss, mac_nss);
 
 	struct ath12k_wmi_peer_assoc_arg *peer_arg __free(kfree) =
 					kzalloc(sizeof(*peer_arg), GFP_KERNEL);
@@ -5776,6 +6024,8 @@ static void ath12k_sta_rc_update_wk(struct wiphy *wiphy, struct wiphy_work *wk)
 		mask = &arvif->bitrate_mask;
 		num_vht_rates = ath12k_mac_bitrate_mask_num_vht_rates(ar, band,
 								      mask);
+		num_he_rates = ath12k_mac_bitrate_mask_num_he_rates(ar, band,
+								    mask);
 
 		/* Peer_assoc_prepare will reject vht rates in
 		 * bitrate_mask if its not available in range format and
@@ -5798,11 +6048,24 @@ static void ath12k_sta_rc_update_wk(struct wiphy *wiphy, struct wiphy_work *wk)
 		if (link_sta->vht_cap.vht_supported && num_vht_rates == 1) {
 			ath12k_mac_set_peer_vht_fixed_rate(arvif, arsta, mask,
 							   band);
+		} else if (link_sta->he_cap.has_he && num_he_rates == 1) {
+			ath12k_mac_set_peer_he_fixed_rate(arvif, arsta, mask, band);
 		} else {
-			/* If the peer is non-VHT or no fixed VHT rate
+			/* If the peer is non-VHT/HE or no fixed VHT/HE rate
 			 * is provided in the new bitrate mask we set the
-			 * other rates using peer_assoc command.
+			 * other rates using peer_assoc command. Also clear
+			 * the peer fixed rate settings as it has higher proprity
+			 * than peer assoc
 			 */
+			err = ath12k_wmi_set_peer_param(ar, arsta->addr,
+							arvif->vdev_id,
+							WMI_PEER_PARAM_FIXED_RATE,
+							WMI_FIXED_RATE_NONE);
+			if (err)
+				ath12k_warn(ar->ab,
+					    "failed to disable peer fixed rate for STA %pM ret %d\n",
+					    arsta->addr, err);
+
 			ath12k_peer_assoc_prepare(ar, arvif, arsta,
 						  peer_arg, true);
 
@@ -11269,19 +11532,40 @@ ath12k_mac_has_single_legacy_rate(struct ath12k *ar,
 	if (ath12k_mac_bitrate_mask_num_vht_rates(ar, band, mask))
 		return false;
 
+	if (ath12k_mac_bitrate_mask_num_he_rates(ar, band, mask))
+		return false;
+
 	return num_rates == 1;
 }
 
+static __le16
+ath12k_mac_get_tx_mcs_map(const struct ieee80211_sta_he_cap *he_cap)
+{
+	if (he_cap->he_cap_elem.phy_cap_info[0] &
+	    IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G)
+		return he_cap->he_mcs_nss_supp.tx_mcs_80p80;
+
+	if (he_cap->he_cap_elem.phy_cap_info[0] &
+	    IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G)
+		return he_cap->he_mcs_nss_supp.tx_mcs_160;
+
+	return he_cap->he_mcs_nss_supp.tx_mcs_80;
+}
+
 static bool
 ath12k_mac_bitrate_mask_get_single_nss(struct ath12k *ar,
+				       struct ieee80211_vif *vif,
 				       enum nl80211_band band,
 				       const struct cfg80211_bitrate_mask *mask,
 				       int *nss)
 {
 	struct ieee80211_supported_band *sband = &ar->mac.sbands[band];
 	u16 vht_mcs_map = le16_to_cpu(sband->vht_cap.vht_mcs.tx_mcs_map);
+	const struct ieee80211_sta_he_cap *he_cap;
+	u16 he_mcs_map = 0;
 	u8 ht_nss_mask = 0;
 	u8 vht_nss_mask = 0;
+	u8 he_nss_mask = 0;
 	int i;
 
 	/* No need to consider legacy here. Basic rates are always present
@@ -11308,7 +11592,24 @@ ath12k_mac_bitrate_mask_get_single_nss(struct ath12k *ar,
 			return false;
 	}
 
-	if (ht_nss_mask != vht_nss_mask)
+	he_cap = ieee80211_get_he_iftype_cap_vif(sband, vif);
+	if (!he_cap)
+		return false;
+
+	he_mcs_map = le16_to_cpu(ath12k_mac_get_tx_mcs_map(he_cap));
+
+	for (i = 0; i < ARRAY_SIZE(mask->control[band].he_mcs); i++) {
+		if (mask->control[band].he_mcs[i] == 0)
+			continue;
+
+		if (mask->control[band].he_mcs[i] ==
+		    ath12k_mac_get_max_he_mcs_map(he_mcs_map, i))
+			he_nss_mask |= BIT(i);
+		else
+			return false;
+	}
+
+	if (ht_nss_mask != vht_nss_mask || ht_nss_mask != he_nss_mask)
 		return false;
 
 	if (ht_nss_mask == 0)
@@ -11355,54 +11656,182 @@ ath12k_mac_get_single_legacy_rate(struct ath12k *ar,
 	return 0;
 }
 
-static int ath12k_mac_set_fixed_rate_params(struct ath12k_link_vif *arvif,
-					    u32 rate, u8 nss, u8 sgi, u8 ldpc)
+static int
+ath12k_mac_set_fixed_rate_gi_ltf(struct ath12k_link_vif *arvif, u8 he_gi, u8 he_ltf)
 {
 	struct ath12k *ar = arvif->ar;
-	u32 vdev_param;
 	int ret;
 
 	lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
 
-	ath12k_dbg(ar->ab, ATH12K_DBG_MAC, "mac set fixed rate params vdev %i rate 0x%02x nss %u sgi %u\n",
-		   arvif->vdev_id, rate, nss, sgi);
+	/* 0.8 = 0, 1.6 = 2 and 3.2 = 3. */
+	if (he_gi && he_gi != 0xFF)
+		he_gi += 1;
 
-	vdev_param = WMI_VDEV_PARAM_FIXED_RATE;
 	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
-					    vdev_param, rate);
+					    WMI_VDEV_PARAM_SGI, he_gi);
 	if (ret) {
-		ath12k_warn(ar->ab, "failed to set fixed rate param 0x%02x: %d\n",
-			    rate, ret);
+		ath12k_warn(ar->ab, "failed to set HE GI:%d, error:%d\n",
+			    he_gi, ret);
 		return ret;
 	}
+	/* start from 1 */
+	if (he_ltf != 0xFF)
+		he_ltf += 1;
 
-	vdev_param = WMI_VDEV_PARAM_NSS;
 	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
-					    vdev_param, nss);
+					    WMI_VDEV_PARAM_HE_LTF, he_ltf);
 	if (ret) {
-		ath12k_warn(ar->ab, "failed to set nss param %d: %d\n",
-			    nss, ret);
+		ath12k_warn(ar->ab, "failed to set HE LTF:%d, error:%d\n",
+			    he_ltf, ret);
+		return ret;
+	}
+	return 0;
+}
+
+static int
+ath12k_mac_set_auto_rate_gi_ltf(struct ath12k_link_vif *arvif, u16 he_gi, u8 he_ltf)
+{
+	struct ath12k *ar = arvif->ar;
+	int ret;
+	u32 he_ar_gi_ltf;
+
+	if (he_gi != 0xFF) {
+		switch (he_gi) {
+		case NL80211_RATE_INFO_HE_GI_0_8:
+			he_gi = WMI_AUTORATE_800NS_GI;
+			break;
+		case NL80211_RATE_INFO_HE_GI_1_6:
+			he_gi = WMI_AUTORATE_1600NS_GI;
+			break;
+		case NL80211_RATE_INFO_HE_GI_3_2:
+			he_gi = WMI_AUTORATE_3200NS_GI;
+			break;
+		default:
+			ath12k_warn(ar->ab, "Invalid GI\n");
+			return -EINVAL;
+		}
+	}
+
+	if (he_ltf != 0xFF) {
+		switch (he_ltf) {
+		case NL80211_RATE_INFO_HE_1XLTF:
+			he_ltf = WMI_HE_AUTORATE_LTF_1X;
+			break;
+		case NL80211_RATE_INFO_HE_2XLTF:
+			he_ltf = WMI_HE_AUTORATE_LTF_2X;
+			break;
+		case NL80211_RATE_INFO_HE_4XLTF:
+			he_ltf = WMI_HE_AUTORATE_LTF_4X;
+			break;
+		default:
+			ath12k_warn(ar->ab, "Invalid LTF\n");
+			return -EINVAL;
+		}
+	}
+
+	he_ar_gi_ltf = he_gi | he_ltf;
+
+	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
+					    WMI_VDEV_PARAM_AUTORATE_MISC_CFG,
+					    he_ar_gi_ltf);
+	if (ret) {
+		ath12k_warn(ar->ab,
+			    "failed to set HE autorate GI:%u, LTF:%u params, error:%d\n",
+			    he_gi, he_ltf, ret);
 		return ret;
 	}
 
-	vdev_param = WMI_VDEV_PARAM_SGI;
+	return 0;
+}
+
+static u32 ath12k_mac_nlgi_to_wmigi(enum nl80211_txrate_gi gi)
+{
+	switch (gi) {
+	case NL80211_TXRATE_DEFAULT_GI:
+		return WMI_GI_400_NS;
+	case NL80211_TXRATE_FORCE_LGI:
+		return WMI_GI_800_NS;
+	default:
+		return WMI_GI_400_NS;
+	}
+}
+
+static int ath12k_mac_set_rate_params(struct ath12k_link_vif *arvif,
+				      u32 rate, u8 nss, u8 sgi, u8 ldpc,
+				      u8 he_gi, u8 he_ltf, bool he_fixed_rate)
+{
+	struct ieee80211_bss_conf *link_conf;
+	struct ath12k *ar = arvif->ar;
+	u32 vdev_param;
+	u32 param_value;
+	int ret;
+	bool he_support;
+
+	lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
+
+	link_conf = ath12k_mac_get_link_bss_conf(arvif);
+	if (!link_conf)
+		return -EINVAL;
+
+	he_support = link_conf->he_support;
+
+	ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
+		   "mac set rate params vdev %i rate 0x%02x nss 0x%02x sgi 0x%02x ldpc 0x%02x\n",
+		   arvif->vdev_id, rate, nss, sgi, ldpc);
+
+	ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
+		   "he_gi 0x%02x he_ltf 0x%02x he_fixed_rate %d\n", he_gi,
+		   he_ltf, he_fixed_rate);
+
+	if (!he_support) {
+		vdev_param = WMI_VDEV_PARAM_FIXED_RATE;
+		ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
+						    vdev_param, rate);
+		if (ret) {
+			ath12k_warn(ar->ab, "failed to set fixed rate param 0x%02x: %d\n",
+				    rate, ret);
+			return ret;
+		}
+	}
+
+	vdev_param = WMI_VDEV_PARAM_NSS;
+
 	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
-					    vdev_param, sgi);
+					    vdev_param, nss);
 	if (ret) {
-		ath12k_warn(ar->ab, "failed to set sgi param %d: %d\n",
-			    sgi, ret);
+		ath12k_warn(ar->ab, "failed to set nss param %d: %d\n",
+			    nss, ret);
 		return ret;
 	}
 
-	vdev_param = WMI_VDEV_PARAM_LDPC;
 	ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
-					    vdev_param, ldpc);
+					    WMI_VDEV_PARAM_LDPC, ldpc);
 	if (ret) {
 		ath12k_warn(ar->ab, "failed to set ldpc param %d: %d\n",
 			    ldpc, ret);
 		return ret;
 	}
 
+	if (he_support) {
+		if (he_fixed_rate)
+			ret = ath12k_mac_set_fixed_rate_gi_ltf(arvif, he_gi, he_ltf);
+		else
+			ret = ath12k_mac_set_auto_rate_gi_ltf(arvif, he_gi, he_ltf);
+		if (ret)
+			return ret;
+	} else {
+		vdev_param = WMI_VDEV_PARAM_SGI;
+		param_value = ath12k_mac_nlgi_to_wmigi(sgi);
+		ret = ath12k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id,
+						    vdev_param, param_value);
+		if (ret) {
+			ath12k_warn(ar->ab, "failed to set sgi param %d: %d\n",
+				    sgi, ret);
+			return ret;
+		}
+	}
+
 	return 0;
 }
 
@@ -11431,6 +11860,31 @@ ath12k_mac_vht_mcs_range_present(struct ath12k *ar,
 	return true;
 }
 
+static bool
+ath12k_mac_he_mcs_range_present(struct ath12k *ar,
+				enum nl80211_band band,
+				const struct cfg80211_bitrate_mask *mask)
+{
+	int i;
+	u16 he_mcs;
+
+	for (i = 0; i < NL80211_HE_NSS_MAX; i++) {
+		he_mcs = mask->control[band].he_mcs[i];
+
+		switch (he_mcs) {
+		case 0:
+		case BIT(8) - 1:
+		case BIT(10) - 1:
+		case BIT(12) - 1:
+			break;
+		default:
+			return false;
+		}
+	}
+
+	return true;
+}
+
 static void ath12k_mac_set_bitrate_mask_iter(void *data,
 					     struct ieee80211_sta *sta)
 {
@@ -11439,7 +11893,10 @@ static void ath12k_mac_set_bitrate_mask_iter(void *data,
 	struct ath12k_link_sta *arsta;
 	struct ath12k *ar = arvif->ar;
 
-	arsta = rcu_dereference(ahsta->link[arvif->link_id]);
+	lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
+
+	arsta = wiphy_dereference(ath12k_ar_to_hw(ar)->wiphy,
+				  ahsta->link[arvif->link_id]);
 	if (!arsta || arsta->arvif != arvif)
 		return;
 
@@ -11477,6 +11934,61 @@ static void ath12k_mac_disable_peer_fixed_rate(void *data,
 			    arsta->addr, ret);
 }
 
+static bool
+ath12k_mac_validate_fixed_rate_settings(struct ath12k *ar, enum nl80211_band band,
+					const struct cfg80211_bitrate_mask *mask,
+					unsigned int link_id)
+{
+	bool he_fixed_rate = false, vht_fixed_rate = false;
+	const u16 *vht_mcs_mask, *he_mcs_mask;
+	struct ieee80211_link_sta *link_sta;
+	struct ath12k_peer *peer, *tmp;
+	u8 vht_nss, he_nss;
+	int ret = true;
+
+	vht_mcs_mask = mask->control[band].vht_mcs;
+	he_mcs_mask = mask->control[band].he_mcs;
+
+	if (ath12k_mac_bitrate_mask_num_vht_rates(ar, band, mask) == 1)
+		vht_fixed_rate = true;
+
+	if (ath12k_mac_bitrate_mask_num_he_rates(ar, band, mask) == 1)
+		he_fixed_rate = true;
+
+	if (!vht_fixed_rate && !he_fixed_rate)
+		return true;
+
+	vht_nss = ath12k_mac_max_vht_nss(vht_mcs_mask);
+	he_nss =  ath12k_mac_max_he_nss(he_mcs_mask);
+
+	rcu_read_lock();
+	spin_lock_bh(&ar->ab->base_lock);
+	list_for_each_entry_safe(peer, tmp, &ar->ab->peers, list) {
+		if (peer->sta) {
+			link_sta = rcu_dereference(peer->sta->link[link_id]);
+			if (!link_sta) {
+				ret = false;
+				goto exit;
+			}
+
+			if (vht_fixed_rate && (!link_sta->vht_cap.vht_supported ||
+					       link_sta->rx_nss < vht_nss)) {
+				ret = false;
+				goto exit;
+			}
+			if (he_fixed_rate && (!link_sta->he_cap.has_he ||
+					      link_sta->rx_nss < he_nss)) {
+				ret = false;
+				goto exit;
+			}
+		}
+	}
+exit:
+	spin_unlock_bh(&ar->ab->base_lock);
+	rcu_read_unlock();
+	return ret;
+}
+
 static int
 ath12k_mac_op_set_bitrate_mask(struct ieee80211_hw *hw,
 			       struct ieee80211_vif *vif,
@@ -11489,13 +12001,17 @@ ath12k_mac_op_set_bitrate_mask(struct ieee80211_hw *hw,
 	enum nl80211_band band;
 	const u8 *ht_mcs_mask;
 	const u16 *vht_mcs_mask;
+	const u16 *he_mcs_mask;
+	u8 he_ltf = 0;
+	u8 he_gi = 0;
 	u32 rate;
-	u8 nss;
+	u8 nss, mac_nss;
 	u8 sgi;
 	u8 ldpc;
 	int single_nss;
 	int ret;
 	int num_rates;
+	bool he_fixed_rate = false;
 
 	lockdep_assert_wiphy(hw->wiphy);
 
@@ -11510,14 +12026,18 @@ ath12k_mac_op_set_bitrate_mask(struct ieee80211_hw *hw,
 	band = def.chan->band;
 	ht_mcs_mask = mask->control[band].ht_mcs;
 	vht_mcs_mask = mask->control[band].vht_mcs;
+	he_mcs_mask = mask->control[band].he_mcs;
 	ldpc = !!(ar->ht_cap_info & WMI_HT_CAP_LDPC);
 
 	sgi = mask->control[band].gi;
-	if (sgi == NL80211_TXRATE_FORCE_LGI) {
+	if (sgi == NL80211_TXRATE_FORCE_SGI) {
 		ret = -EINVAL;
 		goto out;
 	}
 
+	he_gi = mask->control[band].he_gi;
+	he_ltf = mask->control[band].he_ltf;
+
 	/* mac80211 doesn't support sending a fixed HT/VHT MCS alone, rather it
 	 * requires passing at least one of used basic rates along with them.
 	 * Fixed rate setting across different preambles(legacy, HT, VHT) is
@@ -11534,18 +12054,31 @@ ath12k_mac_op_set_bitrate_mask(struct ieee80211_hw *hw,
 				    arvif->vdev_id, ret);
 			goto out;
 		}
+
 		ieee80211_iterate_stations_mtx(hw,
 					       ath12k_mac_disable_peer_fixed_rate,
 					       arvif);
-	} else if (ath12k_mac_bitrate_mask_get_single_nss(ar, band, mask,
+	} else if (ath12k_mac_bitrate_mask_get_single_nss(ar, vif, band, mask,
 							  &single_nss)) {
 		rate = WMI_FIXED_RATE_NONE;
 		nss = single_nss;
+		arvif->bitrate_mask = *mask;
+
+		ieee80211_iterate_stations_atomic(hw,
+						  ath12k_mac_set_bitrate_mask_iter,
+						  arvif);
 	} else {
 		rate = WMI_FIXED_RATE_NONE;
-		nss = min_t(u32, ar->num_tx_chains,
-			    max(ath12k_mac_max_ht_nss(ht_mcs_mask),
-				ath12k_mac_max_vht_nss(vht_mcs_mask)));
+
+		if (!ath12k_mac_validate_fixed_rate_settings(ar, band,
+							     mask, arvif->link_id))
+			ath12k_warn(ar->ab,
+				    "failed to update fixed rate settings due to mcs/nss incompatibility\n");
+
+		mac_nss = max3(ath12k_mac_max_ht_nss(ht_mcs_mask),
+			       ath12k_mac_max_vht_nss(vht_mcs_mask),
+			       ath12k_mac_max_he_nss(he_mcs_mask));
+		nss = min_t(u32, ar->num_tx_chains, mac_nss);
 
 		/* If multiple rates across different preambles are given
 		 * we can reconfigure this info with all peers using PEER_ASSOC
@@ -11577,9 +12110,21 @@ ath12k_mac_op_set_bitrate_mask(struct ieee80211_hw *hw,
 			 */
 			ath12k_warn(ar->ab,
 				    "Setting more than one MCS Value in bitrate mask not supported\n");
-			return -EINVAL;
+			ret = -EINVAL;
+			goto out;
 		}
 
+		num_rates = ath12k_mac_bitrate_mask_num_he_rates(ar, band, mask);
+		if (num_rates == 1)
+			he_fixed_rate = true;
+
+		if (!ath12k_mac_he_mcs_range_present(ar, band, mask) &&
+		    num_rates > 1) {
+			ath12k_warn(ar->ab,
+				    "Setting more than one HE MCS Value in bitrate mask not supported\n");
+			ret = -EINVAL;
+			goto out;
+		}
 		ieee80211_iterate_stations_mtx(hw,
 					       ath12k_mac_disable_peer_fixed_rate,
 					       arvif);
@@ -11590,9 +12135,10 @@ ath12k_mac_op_set_bitrate_mask(struct ieee80211_hw *hw,
 					       arvif);
 	}
 
-	ret = ath12k_mac_set_fixed_rate_params(arvif, rate, nss, sgi, ldpc);
+	ret = ath12k_mac_set_rate_params(arvif, rate, nss, sgi, ldpc, he_gi,
+					 he_ltf, he_fixed_rate);
 	if (ret) {
-		ath12k_warn(ar->ab, "failed to set fixed rate params on vdev %i: %d\n",
+		ath12k_warn(ar->ab, "failed to set rate params on vdev %i: %d\n",
 			    arvif->vdev_id, ret);
 	}
 
diff --git a/drivers/net/wireless/ath/ath12k/wmi.h b/drivers/net/wireless/ath/ath12k/wmi.h
index 7ad84624600d..be3672304478 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.h
+++ b/drivers/net/wireless/ath/ath12k/wmi.h
@@ -222,6 +222,22 @@ enum WMI_HOST_WLAN_BAND {
 	WMI_HOST_WLAN_2GHZ_5GHZ_CAP	= 3,
 };
 
+/* Parameters used for WMI_VDEV_PARAM_AUTORATE_MISC_CFG command.
+ * Used only for HE auto rate mode.
+ */
+enum {
+	/* HE LTF related configuration */
+	WMI_HE_AUTORATE_LTF_1X = BIT(0),
+	WMI_HE_AUTORATE_LTF_2X = BIT(1),
+	WMI_HE_AUTORATE_LTF_4X = BIT(2),
+
+	/* HE GI related configuration */
+	WMI_AUTORATE_400NS_GI = BIT(8),
+	WMI_AUTORATE_800NS_GI = BIT(9),
+	WMI_AUTORATE_1600NS_GI = BIT(10),
+	WMI_AUTORATE_3200NS_GI = BIT(11),
+};
+
 enum wmi_cmd_group {
 	/* 0 to 2 are reserved */
 	WMI_GRP_START = 0x3,
@@ -1171,7 +1187,9 @@ enum wmi_tlv_vdev_param {
 	WMI_VDEV_PARAM_HE_RANGE_EXT,
 	WMI_VDEV_PARAM_ENABLE_BCAST_PROBE_RESPONSE,
 	WMI_VDEV_PARAM_FILS_MAX_CHANNEL_GUARD_TIME,
+	WMI_VDEV_PARAM_HE_LTF = 0x74,
 	WMI_VDEV_PARAM_BA_MODE = 0x7e,
+	WMI_VDEV_PARAM_AUTORATE_MISC_CFG = 0x80,
 	WMI_VDEV_PARAM_SET_HE_SOUNDING_MODE = 0x87,
 	WMI_VDEV_PARAM_6GHZ_PARAMS = 0x99,
 	WMI_VDEV_PARAM_PROTOTYPE = 0x8000,
@@ -3636,6 +3654,15 @@ struct wmi_force_fw_hang_cmd {
 	__le32 delay_time_ms;
 } __packed;
 
+/* Param values to be sent for WMI_VDEV_PARAM_SGI param_id
+ * which are used in 11n, 11ac systems
+ * @WMI_GI_800_NS - Always uses 0.8us (Long GI)
+ * @WMI_GI_400_NS - Firmware switches between 0.4us (Short GI)
+ *			and 0.8us (Long GI) based on packet error rate.
+ */
+#define WMI_GI_800_NS 0
+#define WMI_GI_400_NS 1
+
 struct wmi_vdev_set_param_cmd {
 	__le32 tlv_header;
 	__le32 vdev_id;
-- 
2.43.0

[PATCH ath-next V15 7/9] wifi: ath12k: clean up 80P80 support

[Pradeep Kumar Chitrapu]

Clean up unused 80P80 references as hardware does not support
it. This is applicable to both QCN9274 and WCN7850.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 48 ++++++---------------------
 drivers/net/wireless/ath/ath12k/wmi.c |  2 --
 drivers/net/wireless/ath/ath12k/wmi.h |  1 -
 3 files changed, 10 insertions(+), 41 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index aefb620b28e2..8fba1bd2e372 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -209,7 +209,7 @@ ath12k_phymodes[NUM_NL80211_BANDS][ATH12K_CHAN_WIDTH_NUM] = {
 			[NL80211_CHAN_WIDTH_40] = MODE_11BE_EHT40,
 			[NL80211_CHAN_WIDTH_80] = MODE_11BE_EHT80,
 			[NL80211_CHAN_WIDTH_160] = MODE_11BE_EHT160,
-			[NL80211_CHAN_WIDTH_80P80] = MODE_11BE_EHT80_80,
+			[NL80211_CHAN_WIDTH_80P80] = MODE_UNKNOWN,
 			[NL80211_CHAN_WIDTH_320] = MODE_11BE_EHT320,
 	},
 	[NL80211_BAND_6GHZ] = {
@@ -220,7 +220,7 @@ ath12k_phymodes[NUM_NL80211_BANDS][ATH12K_CHAN_WIDTH_NUM] = {
 			[NL80211_CHAN_WIDTH_40] = MODE_11BE_EHT40,
 			[NL80211_CHAN_WIDTH_80] = MODE_11BE_EHT80,
 			[NL80211_CHAN_WIDTH_160] = MODE_11BE_EHT160,
-			[NL80211_CHAN_WIDTH_80P80] = MODE_11BE_EHT80_80,
+			[NL80211_CHAN_WIDTH_80P80] = MODE_UNKNOWN,
 			[NL80211_CHAN_WIDTH_320] = MODE_11BE_EHT320,
 	},
 
@@ -2574,17 +2574,6 @@ static void ath12k_peer_assoc_h_he(struct ath12k *ar,
 
 	switch (link_sta->bandwidth) {
 	case IEEE80211_STA_RX_BW_160:
-		if (he_cap->he_cap_elem.phy_cap_info[0] &
-		    IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G) {
-			v = ath12k_peer_assoc_h_he_limit(v, he_mcs_mask);
-			arg->peer_he_rx_mcs_set[WMI_HECAP_TXRX_MCS_NSS_IDX_80_80] = v;
-
-			v = le16_to_cpu(he_cap->he_mcs_nss_supp.tx_mcs_80p80);
-			arg->peer_he_tx_mcs_set[WMI_HECAP_TXRX_MCS_NSS_IDX_80_80] = v;
-
-			arg->peer_he_mcs_count++;
-			he_tx_mcs = v;
-		}
 		v = le16_to_cpu(he_cap->he_mcs_nss_supp.rx_mcs_160);
 		arg->peer_he_rx_mcs_set[WMI_HECAP_TXRX_MCS_NSS_IDX_160] = v;
 
@@ -2871,16 +2860,11 @@ static enum wmi_phy_mode ath12k_mac_get_phymode_vht(struct ath12k *ar,
 						    struct ieee80211_link_sta *link_sta)
 {
 	if (link_sta->bandwidth == IEEE80211_STA_RX_BW_160) {
-		switch (link_sta->vht_cap.cap &
-			IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK) {
-		case IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ:
-			return MODE_11AC_VHT160;
-		case IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ:
-			return MODE_11AC_VHT80_80;
-		default:
-			/* not sure if this is a valid case? */
+		if (link_sta->vht_cap.cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ)
 			return MODE_11AC_VHT160;
-		}
+
+		/* not sure if this is a valid case? */
+		return MODE_11AC_VHT160;
 	}
 
 	if (link_sta->bandwidth == IEEE80211_STA_RX_BW_80)
@@ -2902,11 +2886,8 @@ static enum wmi_phy_mode ath12k_mac_get_phymode_he(struct ath12k *ar,
 		if (link_sta->he_cap.he_cap_elem.phy_cap_info[0] &
 		     IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G)
 			return MODE_11AX_HE160;
-		else if (link_sta->he_cap.he_cap_elem.phy_cap_info[0] &
-		     IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G)
-			return MODE_11AX_HE80_80;
-		/* not sure if this is a valid case? */
-		return MODE_11AX_HE160;
+
+		return MODE_UNKNOWN;
 	}
 
 	if (link_sta->bandwidth == IEEE80211_STA_RX_BW_80)
@@ -2934,14 +2915,10 @@ static enum wmi_phy_mode ath12k_mac_get_phymode_eht(struct ath12k *ar,
 		    IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G)
 			return MODE_11BE_EHT160;
 
-		if (link_sta->he_cap.he_cap_elem.phy_cap_info[0] &
-			 IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G)
-			return MODE_11BE_EHT80_80;
-
 		ath12k_warn(ar->ab, "invalid EHT PHY capability info for 160 Mhz: %d\n",
 			    link_sta->he_cap.he_cap_elem.phy_cap_info[0]);
 
-		return MODE_11BE_EHT160;
+		return MODE_UNKNOWN;
 	}
 
 	if (link_sta->bandwidth == IEEE80211_STA_RX_BW_80)
@@ -7828,8 +7805,6 @@ static void ath12k_mac_set_hemcsmap(struct ath12k *ar,
 	mcs_nss->tx_mcs_80 = cpu_to_le16(txmcs_map & 0xffff);
 	mcs_nss->rx_mcs_160 = cpu_to_le16(rxmcs_map & 0xffff);
 	mcs_nss->tx_mcs_160 = cpu_to_le16(txmcs_map & 0xffff);
-	mcs_nss->rx_mcs_80p80 = cpu_to_le16(rxmcs_map & 0xffff);
-	mcs_nss->tx_mcs_80p80 = cpu_to_le16(txmcs_map & 0xffff);
 }
 
 static void ath12k_mac_copy_he_cap(struct ath12k *ar,
@@ -7851,6 +7826,7 @@ static void ath12k_mac_copy_he_cap(struct ath12k *ar,
 		IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_IN_2G |
 		IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G |
 		IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G;
+	/* 80PLUS80 is not supported */
 	he_cap_elem->phy_cap_info[0] &=
 		~IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G;
 	he_cap_elem->phy_cap_info[5] &=
@@ -11541,10 +11517,6 @@ ath12k_mac_has_single_legacy_rate(struct ath12k *ar,
 static __le16
 ath12k_mac_get_tx_mcs_map(const struct ieee80211_sta_he_cap *he_cap)
 {
-	if (he_cap->he_cap_elem.phy_cap_info[0] &
-	    IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G)
-		return he_cap->he_mcs_nss_supp.tx_mcs_80p80;
-
 	if (he_cap->he_cap_elem.phy_cap_info[0] &
 	    IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G)
 		return he_cap->he_mcs_nss_supp.tx_mcs_160;
diff --git a/drivers/net/wireless/ath/ath12k/wmi.c b/drivers/net/wireless/ath/ath12k/wmi.c
index cdf3406302ee..1ad21bd1583a 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.c
+++ b/drivers/net/wireless/ath/ath12k/wmi.c
@@ -1066,8 +1066,6 @@ static void ath12k_wmi_put_wmi_channel(struct ath12k_wmi_channel_params *chan,
 			chan->band_center_freq1 = cpu_to_le32(center_freq1 - 40);
 
 		chan->band_center_freq2 = cpu_to_le32(center_freq1);
-	} else if (arg->mode == MODE_11BE_EHT80_80) {
-		chan->band_center_freq2 = cpu_to_le32(arg->band_center_freq2);
 	} else {
 		chan->band_center_freq2 = 0;
 	}
diff --git a/drivers/net/wireless/ath/ath12k/wmi.h b/drivers/net/wireless/ath/ath12k/wmi.h
index be3672304478..74f3ab90bbcd 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.h
+++ b/drivers/net/wireless/ath/ath12k/wmi.h
@@ -3804,7 +3804,6 @@ struct wmi_vdev_install_key_arg {
 #define WMI_HOST_MAX_HE_RATE_SET		3
 #define WMI_HECAP_TXRX_MCS_NSS_IDX_80		0
 #define WMI_HECAP_TXRX_MCS_NSS_IDX_160		1
-#define WMI_HECAP_TXRX_MCS_NSS_IDX_80_80	2
 
 #define ATH12K_WMI_MLO_MAX_PARTNER_LINKS \
 	(ATH12K_WMI_MLO_MAX_LINKS + ATH12K_MAX_NUM_BRIDGE_LINKS - 1)
-- 
2.43.0

[PATCH ath-next V15 8/9] wifi: ath12k: add support for 160 MHz bandwidth

[Pradeep Kumar Chitrapu]

Add support to configure maximum NSS in 160 MHz bandwidth.
Firmware advertises support for handling NSS ratio information
as a part of service ready ext event using nss_ratio_enabled
flag. Save this information in ath12k_pdev_cap to calculate
NSS ratio.

Additionally, reorder the code by moving
ath12k_peer_assoc_h_phymode() before ath12k_peer_assoc_h_vht()
to ensure that arg->peer_phymode correctly reflects the bandwidth
in the max NSS calculation.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/core.h |  2 +
 drivers/net/wireless/ath/ath12k/mac.c  | 89 ++++++++++++++++++++++----
 drivers/net/wireless/ath/ath12k/mac.h  |  2 +
 drivers/net/wireless/ath/ath12k/wmi.c  |  7 +-
 drivers/net/wireless/ath/ath12k/wmi.h  | 21 ++++++
 5 files changed, 108 insertions(+), 13 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/core.h b/drivers/net/wireless/ath/ath12k/core.h
index 3c10d7eb9669..96ff9b08a848 100644
--- a/drivers/net/wireless/ath/ath12k/core.h
+++ b/drivers/net/wireless/ath/ath12k/core.h
@@ -894,6 +894,8 @@ struct ath12k_pdev_cap {
 	struct ath12k_band_cap band[NUM_NL80211_BANDS];
 	u32 eml_cap;
 	u32 mld_cap;
+	bool nss_ratio_enabled;
+	u8 nss_ratio_info;
 };
 
 struct mlo_timestamp {
diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index 8fba1bd2e372..c0d58a587d6a 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -2203,6 +2203,34 @@ ath12k_peer_assoc_h_vht_limit(u16 tx_mcs_set,
 	return tx_mcs_set;
 }
 
+static u8 ath12k_get_nss_160mhz(struct ath12k *ar,
+				u8 max_nss)
+{
+	u8 nss_ratio_info = ar->pdev->cap.nss_ratio_info;
+	u8 max_sup_nss = 0;
+
+	switch (nss_ratio_info) {
+	case WMI_NSS_RATIO_1BY2_NSS:
+		max_sup_nss = max_nss >> 1;
+		break;
+	case WMI_NSS_RATIO_3BY4_NSS:
+		ath12k_warn(ar->ab, "WMI_NSS_RATIO_3BY4_NSS not supported\n");
+		break;
+	case WMI_NSS_RATIO_1_NSS:
+		max_sup_nss = max_nss;
+		break;
+	case WMI_NSS_RATIO_2_NSS:
+		ath12k_warn(ar->ab, "WMI_NSS_RATIO_2_NSS not supported\n");
+		break;
+	default:
+		ath12k_warn(ar->ab, "invalid nss ratio received from fw: %d\n",
+			    nss_ratio_info);
+		break;
+	}
+
+	return max_sup_nss;
+}
+
 static void ath12k_peer_assoc_h_vht(struct ath12k *ar,
 				    struct ath12k_link_vif *arvif,
 				    struct ath12k_link_sta *arsta,
@@ -2220,6 +2248,7 @@ static void ath12k_peer_assoc_h_vht(struct ath12k *ar,
 	u8 max_nss, vht_mcs;
 	int i, vht_nss, nss_idx;
 	bool user_rate_valid = true;
+	u32 rx_nss, tx_nss, nss_160;
 
 	lockdep_assert_wiphy(ath12k_ar_to_hw(ar)->wiphy);
 
@@ -2324,10 +2353,24 @@ static void ath12k_peer_assoc_h_vht(struct ath12k *ar,
 	/* TODO:  Check */
 	arg->tx_max_mcs_nss = 0xFF;
 
-	ath12k_dbg(ar->ab, ATH12K_DBG_MAC, "mac vht peer %pM max_mpdu %d flags 0x%x\n",
-		   arsta->addr, arg->peer_max_mpdu, arg->peer_flags);
+	if (arg->peer_phymode == MODE_11AC_VHT160) {
+		tx_nss = ath12k_get_nss_160mhz(ar, max_nss);
+		rx_nss = min(arg->peer_nss, tx_nss);
+		arg->peer_bw_rxnss_override = ATH12K_BW_NSS_MAP_ENABLE;
+
+		if (!rx_nss) {
+			ath12k_warn(ar->ab, "invalid max_nss\n");
+			return;
+		}
+
+		nss_160 = u32_encode_bits(rx_nss - 1, ATH12K_PEER_RX_NSS_160MHZ);
+		arg->peer_bw_rxnss_override |= nss_160;
+	}
 
-	/* TODO: rxnss_override */
+	ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
+		   "mac vht peer %pM max_mpdu %d flags 0x%x nss_override 0x%x\n",
+		   arsta->addr, arg->peer_max_mpdu, arg->peer_flags,
+		   arg->peer_bw_rxnss_override);
 }
 
 static int ath12k_mac_get_max_he_mcs_map(u16 mcs_map, int nss)
@@ -2420,6 +2463,7 @@ static void ath12k_peer_assoc_h_he(struct ath12k *ar,
 	u16 he_tx_mcs = 0, v = 0;
 	int he_nss, nss_idx;
 	bool user_rate_valid = true;
+	u32 rx_nss, tx_nss, nss_160;
 
 	if (WARN_ON(ath12k_mac_vif_link_chan(vif, link_id, &def)))
 		return;
@@ -2617,9 +2661,25 @@ static void ath12k_peer_assoc_h_he(struct ath12k *ar,
 	max_nss = min(max_nss, ar->num_tx_chains);
 	arg->peer_nss = min(link_sta->rx_nss, max_nss);
 
+	if (arg->peer_phymode == MODE_11AX_HE160) {
+		tx_nss = ath12k_get_nss_160mhz(ar, max_nss);
+		rx_nss = min(arg->peer_nss, tx_nss);
+		arg->peer_bw_rxnss_override = ATH12K_BW_NSS_MAP_ENABLE;
+
+		if (!rx_nss) {
+			ath12k_warn(ar->ab, "invalid max_nss\n");
+			return;
+		}
+
+		nss_160 = u32_encode_bits(rx_nss - 1, ATH12K_PEER_RX_NSS_160MHZ);
+		arg->peer_bw_rxnss_override |= nss_160;
+	}
+
 	ath12k_dbg(ar->ab, ATH12K_DBG_MAC,
-		   "mac he peer %pM nss %d mcs cnt %d\n",
-		   arsta->addr, arg->peer_nss, arg->peer_he_mcs_count);
+		   "mac he peer %pM nss %d mcs cnt %d nss_override 0x%x\n",
+		   arsta->addr, arg->peer_nss,
+		   arg->peer_he_mcs_count,
+		   arg->peer_bw_rxnss_override);
 }
 
 static void ath12k_peer_assoc_h_he_6ghz(struct ath12k *ar,
@@ -2860,10 +2920,13 @@ static enum wmi_phy_mode ath12k_mac_get_phymode_vht(struct ath12k *ar,
 						    struct ieee80211_link_sta *link_sta)
 {
 	if (link_sta->bandwidth == IEEE80211_STA_RX_BW_160) {
-		if (link_sta->vht_cap.cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ)
+		if (link_sta->vht_cap.cap & (IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ |
+		    IEEE80211_VHT_CAP_EXT_NSS_BW_MASK))
 			return MODE_11AC_VHT160;
 
-		/* not sure if this is a valid case? */
+		/* Allow STA to connect even if it does not explicitly advertise 160 MHz
+		 * support
+		 */
 		return MODE_11AC_VHT160;
 	}
 
@@ -7575,10 +7638,8 @@ ath12k_create_vht_cap(struct ath12k *ar, u32 rate_cap_tx_chainmask,
 
 	ath12k_set_vht_txbf_cap(ar, &vht_cap.cap);
 
-	/* TODO: Enable back VHT160 mode once association issues are fixed */
-	/* Disabling VHT160 and VHT80+80 modes */
-	vht_cap.cap &= ~IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK;
-	vht_cap.cap &= ~IEEE80211_VHT_CAP_SHORT_GI_160;
+	/* 80P80 is not supported */
+	vht_cap.cap &= ~IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ;
 
 	rxmcs_map = 0;
 	txmcs_map = 0;
@@ -12974,7 +13035,8 @@ ath12k_mac_setup_radio_iface_comb(struct ath12k *ar,
 		comb[0].radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) |
 						BIT(NL80211_CHAN_WIDTH_20) |
 						BIT(NL80211_CHAN_WIDTH_40) |
-						BIT(NL80211_CHAN_WIDTH_80);
+						BIT(NL80211_CHAN_WIDTH_80) |
+						BIT(NL80211_CHAN_WIDTH_160);
 	}
 
 	return 0;
@@ -13356,6 +13418,9 @@ static int ath12k_mac_hw_register(struct ath12k_hw *ah)
 	ieee80211_hw_set(hw, REPORTS_LOW_ACK);
 	ieee80211_hw_set(hw, NO_VIRTUAL_MONITOR);
 
+	if (cap->nss_ratio_enabled)
+		ieee80211_hw_set(hw, SUPPORTS_VHT_EXT_NSS_BW);
+
 	if ((ht_cap & WMI_HT_CAP_ENABLED) || is_6ghz) {
 		ieee80211_hw_set(hw, AMPDU_AGGREGATION);
 		ieee80211_hw_set(hw, TX_AMPDU_SETUP_IN_HW);
diff --git a/drivers/net/wireless/ath/ath12k/mac.h b/drivers/net/wireless/ath/ath12k/mac.h
index 9241afe7dc02..18c79d4002cb 100644
--- a/drivers/net/wireless/ath/ath12k/mac.h
+++ b/drivers/net/wireless/ath/ath12k/mac.h
@@ -41,6 +41,8 @@ struct ath12k_generic_iter {
 #define IEEE80211_DISABLE_VHT_MCS_SUPPORT_0_11	BIT(24)
 
 #define ATH12K_CHAN_WIDTH_NUM			14
+#define ATH12K_BW_NSS_MAP_ENABLE		BIT(31)
+#define ATH12K_PEER_RX_NSS_160MHZ		GENMASK(2, 0)
 
 #define ATH12K_TX_POWER_MAX_VAL	70
 #define ATH12K_TX_POWER_MIN_VAL	0
diff --git a/drivers/net/wireless/ath/ath12k/wmi.c b/drivers/net/wireless/ath/ath12k/wmi.c
index 1ad21bd1583a..07040847c01d 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.c
+++ b/drivers/net/wireless/ath/ath12k/wmi.c
@@ -537,6 +537,10 @@ ath12k_pull_mac_phy_cap_svc_ready_ext(struct ath12k_wmi_pdev *wmi_handle,
 		pdev_cap->he_mcs = le32_to_cpu(mac_caps->he_supp_mcs_5g);
 		pdev_cap->tx_chain_mask = le32_to_cpu(mac_caps->tx_chain_mask_5g);
 		pdev_cap->rx_chain_mask = le32_to_cpu(mac_caps->rx_chain_mask_5g);
+		pdev_cap->nss_ratio_enabled =
+			WMI_NSS_RATIO_EN_DIS_GET(mac_caps->nss_ratio);
+		pdev_cap->nss_ratio_info =
+			WMI_NSS_RATIO_INFO_GET(mac_caps->nss_ratio);
 	} else {
 		return -EINVAL;
 	}
@@ -1059,7 +1063,8 @@ static void ath12k_wmi_put_wmi_channel(struct ath12k_wmi_channel_params *chan,
 
 		chan->band_center_freq2 = cpu_to_le32(center_freq1);
 
-	} else if (arg->mode == MODE_11BE_EHT160) {
+	} else if (arg->mode == MODE_11BE_EHT160 ||
+		   arg->mode == MODE_11AX_HE160) {
 		if (arg->freq > center_freq1)
 			chan->band_center_freq1 = cpu_to_le32(center_freq1 + 40);
 		else
diff --git a/drivers/net/wireless/ath/ath12k/wmi.h b/drivers/net/wireless/ath/ath12k/wmi.h
index 74f3ab90bbcd..c6cc513e7a28 100644
--- a/drivers/net/wireless/ath/ath12k/wmi.h
+++ b/drivers/net/wireless/ath/ath12k/wmi.h
@@ -2333,6 +2333,21 @@ enum wmi_direct_buffer_module {
 	WMI_DIRECT_BUF_MAX
 };
 
+/**
+ * enum wmi_nss_ratio - NSS ratio received from FW during service ready ext event
+ * @WMI_NSS_RATIO_1BY2_NSS: Max nss of 160MHz is equals to half of the max nss of 80MHz
+ * @WMI_NSS_RATIO_3BY4_NSS: Max nss of 160MHz is equals to 3/4 of the max nss of 80MHz
+ * @WMI_NSS_RATIO_1_NSS: Max nss of 160MHz is equals to the max nss of 80MHz
+ * @WMI_NSS_RATIO_2_NSS: Max nss of 160MHz is equals to two times the max nss of 80MHz
+ */
+
+enum wmi_nss_ratio {
+	WMI_NSS_RATIO_1BY2_NSS,
+	WMI_NSS_RATIO_3BY4_NSS,
+	WMI_NSS_RATIO_1_NSS,
+	WMI_NSS_RATIO_2_NSS
+};
+
 struct ath12k_wmi_pdev_band_arg {
 	u32 pdev_id;
 	u32 start_freq;
@@ -2652,6 +2667,12 @@ struct ath12k_wmi_hw_mode_cap_params {
 } __packed;
 
 #define WMI_MAX_HECAP_PHY_SIZE                 (3)
+#define WMI_NSS_RATIO_EN_DIS_BITPOS    BIT(0)
+#define WMI_NSS_RATIO_EN_DIS_GET(_val) \
+	le32_get_bits(_val, WMI_NSS_RATIO_EN_DIS_BITPOS)
+#define WMI_NSS_RATIO_INFO_BITPOS              GENMASK(4, 1)
+#define WMI_NSS_RATIO_INFO_GET(_val) \
+	le32_get_bits(_val, WMI_NSS_RATIO_INFO_BITPOS)
 
 /* pdev_id is present in lower 16 bits of pdev_and_hw_link_ids in
  * ath12k_wmi_mac_phy_caps_params & ath12k_wmi_caps_ext_params.
-- 
2.43.0

[PATCH ath-next V15 9/9] wifi: ath12k: add extended NSS bandwidth support for 160 MHz

[Pradeep Kumar Chitrapu]

Currently rx and tx MCS map for 160 MHz under HE capabilities
are not updating properly, when 160 MHz is configured with NSS
lesser than max NSS support. Fix this by utilizing
nss_ratio_enabled and nss_ratio_info fields sent by firmware
in service ready event.

However, if firmware advertises EXT NSS BW support in VHT caps
as 1(1x2) and when nss_ratio_info indicates 1:1, reset the EXT
NSS BW Support in VHT caps to 0 which indicates 1x1. This is
to avoid incorrectly choosing 1:2 NSS ratio when using the
default VHT caps advertised by firmware.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1

Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
---
 drivers/net/wireless/ath/ath12k/mac.c | 33 ++++++++++++++++++++++-----
 1 file changed, 27 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/ath/ath12k/mac.c b/drivers/net/wireless/ath/ath12k/mac.c
index c0d58a587d6a..6dd4441ce9a0 100644
--- a/drivers/net/wireless/ath/ath12k/mac.c
+++ b/drivers/net/wireless/ath/ath12k/mac.c
@@ -2662,8 +2662,10 @@ static void ath12k_peer_assoc_h_he(struct ath12k *ar,
 	arg->peer_nss = min(link_sta->rx_nss, max_nss);
 
 	if (arg->peer_phymode == MODE_11AX_HE160) {
-		tx_nss = ath12k_get_nss_160mhz(ar, max_nss);
+		tx_nss = ath12k_get_nss_160mhz(ar, ar->num_tx_chains);
 		rx_nss = min(arg->peer_nss, tx_nss);
+
+		arg->peer_nss = min(link_sta->rx_nss, ar->num_rx_chains);
 		arg->peer_bw_rxnss_override = ATH12K_BW_NSS_MAP_ENABLE;
 
 		if (!rx_nss) {
@@ -7661,6 +7663,12 @@ ath12k_create_vht_cap(struct ath12k *ar, u32 rate_cap_tx_chainmask,
 	vht_cap.vht_mcs.rx_mcs_map = cpu_to_le16(rxmcs_map);
 	vht_cap.vht_mcs.tx_mcs_map = cpu_to_le16(txmcs_map);
 
+	/* Check if the HW supports 1:1 NSS ratio and reset
+	 * EXT NSS BW Support field to 0 to indicate 1:1 ratio
+	 */
+	if (ar->pdev->cap.nss_ratio_info == WMI_NSS_RATIO_1_NSS)
+		vht_cap.cap &= ~IEEE80211_VHT_CAP_EXT_NSS_BW_MASK;
+
 	return vht_cap;
 }
 
@@ -7843,11 +7851,12 @@ static void ath12k_mac_set_hemcsmap(struct ath12k *ar,
 				    struct ieee80211_sta_he_cap *he_cap)
 {
 	struct ieee80211_he_mcs_nss_supp *mcs_nss = &he_cap->he_mcs_nss_supp;
-	u16 txmcs_map, rxmcs_map;
+	u8 maxtxnss_160 = ath12k_get_nss_160mhz(ar, ar->num_tx_chains);
+	u8 maxrxnss_160 = ath12k_get_nss_160mhz(ar, ar->num_rx_chains);
+	u16 txmcs_map_160 = 0, rxmcs_map_160 = 0;
+	u16 txmcs_map = 0, rxmcs_map = 0;
 	u32 i;
 
-	rxmcs_map = 0;
-	txmcs_map = 0;
 	for (i = 0; i < 8; i++) {
 		if (i < ar->num_tx_chains &&
 		    (ar->cfg_tx_chainmask >> cap->tx_chain_mask_shift) & BIT(i))
@@ -7860,12 +7869,24 @@ static void ath12k_mac_set_hemcsmap(struct ath12k *ar,
 			rxmcs_map |= IEEE80211_HE_MCS_SUPPORT_0_11 << (i * 2);
 		else
 			rxmcs_map |= IEEE80211_HE_MCS_NOT_SUPPORTED << (i * 2);
+
+		if (i < maxtxnss_160 &&
+		    (ar->cfg_tx_chainmask >> cap->tx_chain_mask_shift) & BIT(i))
+			txmcs_map_160 |= IEEE80211_HE_MCS_SUPPORT_0_11 << (i * 2);
+		else
+			txmcs_map_160 |= IEEE80211_HE_MCS_NOT_SUPPORTED << (i * 2);
+
+		if (i < maxrxnss_160 &&
+		    (ar->cfg_tx_chainmask >> cap->tx_chain_mask_shift) & BIT(i))
+			rxmcs_map_160 |= IEEE80211_HE_MCS_SUPPORT_0_11 << (i * 2);
+		else
+			rxmcs_map_160 |= IEEE80211_HE_MCS_NOT_SUPPORTED << (i * 2);
 	}
 
 	mcs_nss->rx_mcs_80 = cpu_to_le16(rxmcs_map & 0xffff);
 	mcs_nss->tx_mcs_80 = cpu_to_le16(txmcs_map & 0xffff);
-	mcs_nss->rx_mcs_160 = cpu_to_le16(rxmcs_map & 0xffff);
-	mcs_nss->tx_mcs_160 = cpu_to_le16(txmcs_map & 0xffff);
+	mcs_nss->rx_mcs_160 = cpu_to_le16(rxmcs_map_160 & 0xffff);
+	mcs_nss->tx_mcs_160 = cpu_to_le16(txmcs_map_160 & 0xffff);
 }
 
 static void ath12k_mac_copy_he_cap(struct ath12k *ar,
-- 
2.43.0

Re: [PATCH ath-next V15 5/9] wifi: ath12k: fix TX and RX MCS rate configurations in HE mode

[Baochen Qiang]

On 7/1/2025 9:04 AM, Pradeep Kumar Chitrapu wrote:
> Currently, the TX and RX MCS rate configurations per peer are
> reversed when sent to the firmware. As a result, RX MCS rates
> are configured for TX, and vice versa. This commit rectifies
> the configuration to match what the firmware expects.

Please mention that you are rectifying only for AP mode. For STA, current code is good.

> 
> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
> 
> Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>

I don't see the need to add my S-O-B here, better drop it.

> Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
> ---
>  drivers/net/wireless/ath/ath12k/wmi.c | 19 +++++++++++++++++--
>  drivers/net/wireless/ath/ath12k/wmi.h |  2 ++
>  2 files changed, 19 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/net/wireless/ath/ath12k/wmi.c b/drivers/net/wireless/ath/ath12k/wmi.c
> index 6c6354b3e18e..cdf3406302ee 100644
> --- a/drivers/net/wireless/ath/ath12k/wmi.c
> +++ b/drivers/net/wireless/ath/ath12k/wmi.c
> @@ -2183,6 +2183,8 @@ int ath12k_wmi_send_peer_assoc_cmd(struct ath12k *ar,
>  				   struct ath12k_wmi_peer_assoc_arg *arg)
>  {
>  	struct ath12k_wmi_pdev *wmi = ar->wmi;
> +	struct ath12k_base *ab = ar->ab;
> +	struct ath12k_link_vif *arvif;
>  	struct wmi_peer_assoc_complete_cmd *cmd;
>  	struct ath12k_wmi_vht_rate_set_params *mcs;
>  	struct ath12k_wmi_he_rate_set_params *he_mcs;
> @@ -2198,6 +2200,13 @@ int ath12k_wmi_send_peer_assoc_cmd(struct ath12k *ar,
>  	u16 eml_cap;
>  	__le32 v;
>  
> +	arvif = ath12k_mac_get_arvif(ar, arg->vdev_id);
> +	if (!arvif) {
> +		ath12k_warn(ab, "failed to find arvif with vdev id %d\n",
> +			    arg->vdev_id);
> +		return -EINVAL;
> +	}
> +
>  	peer_legacy_rates_align = roundup(arg->peer_legacy_rates.num_rates,
>  					  sizeof(u32));
>  	peer_ht_rates_align = roundup(arg->peer_ht_rates.num_rates,
> @@ -2333,8 +2342,14 @@ int ath12k_wmi_send_peer_assoc_cmd(struct ath12k *ar,
>  		he_mcs->tlv_header = ath12k_wmi_tlv_cmd_hdr(WMI_TAG_HE_RATE_SET,
>  							    sizeof(*he_mcs));
>  
> -		he_mcs->rx_mcs_set = cpu_to_le32(arg->peer_he_rx_mcs_set[i]);
> -		he_mcs->tx_mcs_set = cpu_to_le32(arg->peer_he_tx_mcs_set[i]);
> +		if (arvif->ahvif->vdev_type == WMI_VDEV_TYPE_STA) {
> +			he_mcs->rx_mcs_set = cpu_to_le32(arg->peer_he_rx_mcs_set[i]);
> +			he_mcs->tx_mcs_set = cpu_to_le32(arg->peer_he_tx_mcs_set[i]);
> +
> +		} else {
> +			he_mcs->rx_mcs_set = cpu_to_le32(arg->peer_he_tx_mcs_set[i]);
> +			he_mcs->tx_mcs_set = cpu_to_le32(arg->peer_he_rx_mcs_set[i]);
> +		}
>  		ptr += sizeof(*he_mcs);
>  	}
>  
> diff --git a/drivers/net/wireless/ath/ath12k/wmi.h b/drivers/net/wireless/ath/ath12k/wmi.h
> index 0964ca03069a..7ad84624600d 100644
> --- a/drivers/net/wireless/ath/ath12k/wmi.h
> +++ b/drivers/net/wireless/ath/ath12k/wmi.h
> @@ -4162,7 +4162,9 @@ struct ath12k_wmi_vht_rate_set_params {
>  
>  struct ath12k_wmi_he_rate_set_params {
>  	__le32 tlv_header;
> +	/* MCS at which the peer can receive */
>  	__le32 rx_mcs_set;
> +	/* MCS at which the peer can transmit */
>  	__le32 tx_mcs_set;
>  } __packed;
>  

Re: [PATCH ath-next V15 0/9] wifi: ath12k: add MU-MIMO and 160 MHz bandwidth support

[Baochen Qiang]

On 7/1/2025 9:03 AM, Pradeep Kumar Chitrapu wrote:
>   Add support for
> 1. enabling MU-MIMO in HE and EHT modes from hardware
> 2. setting fixed HE rate/GI/LTF
> 3. 160 MHz bandwidth in HE mode
> 4. extended NSS bandwidth support
> 
> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
> 
> changes in v15:
>  - rebased the series after merge conflicts reported
>  patch 4/9:

patch 5/9 ?

>  - change the fix to apply for all modes except STA mode as
>    WCN7850 expect it same as before.

It is not chip specific behavior, for now we believe it is mode behavior.

> 
> changes in v14:
>  patch 6/9:
>  - cap max_nss using ar->num_tx_chains to fix interop issue caused due
>    to sending nss value 4 when firmware only supports nss value 2.
>  patch 8/9:
>  - Set the default return value to MODE_11AC_VHT160 for 160 MHz
>    to allow STA to connect to the AP even if it does not
>    explicitly indicate 160 MHz bandwidth support.
> 
> changes in v13:
>  - rebase
> 
> changes in v12:
>  - rebase
> 
> changes in v11:
>  patch 1/9:
>   - fix return values in ath12k_mac_set_he_txbf_conf() and
>     ath12k_mac_vif_recalc_sta_he_txbf()
>  patch 6/9:
>   - fix missing he_mcs initialization in ath12k_mac_init_arvif()
> 
> changes in v10:
>  patch 6/9:
>   - use ath12k_ahsta_to_sta()
>   - fix rcu_dereference warning in ath12k_mac_set_bitrate_mask_iter()
>   - change return type for ath12k_mac_validate_fixed_rate_settings()
>   - improve readability by adhering to nl80211 definitions of GI
>     NL80211_TXRATE_DEFAULT_GI. Introduce ath12k_mac_nlgi_to_wmigi()
>     for conversion.
>  patch 7/9:
>   - do not change default MODE_11AC_VHT160 in
>     ath12k_mac_get_phymode_vht() as it breaks clients which do not
>     set VHT_CAP_SUPP_CHAN_WIDTH_160MHZ.
>  patch 8/9:
>   - Use IEEE80211_VHT_CAP_EXT_NSS_BW_MASK along with
>     IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ for determining VHT160
>     phymode.
> 
> changes in v9: rebase on top of master branch with mlo changes
>  patch 1/9 and 2/9:
>   - fetch link_conf using ath12k_mac_get_link_bss_conf()
>     instead of arvif->vif->bss_conf before mlo
>  patch 6/9
>   - fetch mcs/nss values from sta->link[] instead of sta->deflink
>   - fix spelling of 'incompatibility'
>  patch 8/9
>   - replace sta->deflink.addr with arsta->addr in
>     ath12k_peer_assoc_h_vht
>  patch 9/9
>   - replace sta->deflink.rx_nss with link_sta->rx_nss
> 
> changes in v8:
>  - rebase and resolve KASAN warnings reported by Jeff in v7, in patch 6/9.
> 
> Pradeep Kumar Chitrapu (9):
>   wifi: ath12k: push HE MU-MIMO params to hardware
>   wifi: ath12k: push EHT MU-MIMO params to hardware
>   wifi: ath12k: move HE MCS mapper to a separate function
>   wifi: ath12k: generate rx and tx mcs maps for supported HE mcs
>   wifi: ath12k: fix TX and RX MCS rate configurations in HE mode
>   wifi: ath12k: add support for setting fixed HE rate/GI/LTF
>   wifi: ath12k: clean up 80P80 support
>   wifi: ath12k: add support for 160 MHz bandwidth
>   wifi: ath12k: add extended NSS bandwidth support for 160 MHz
> 
>  drivers/net/wireless/ath/ath12k/core.h |    2 +
>  drivers/net/wireless/ath/ath12k/mac.c  | 1144 ++++++++++++++++++++----
>  drivers/net/wireless/ath/ath12k/mac.h  |   17 +
>  drivers/net/wireless/ath/ath12k/wmi.c  |   28 +-
>  drivers/net/wireless/ath/ath12k/wmi.h  |  100 ++-
>  5 files changed, 1069 insertions(+), 222 deletions(-)
> 
> 
> base-commit: c256a94d1b1b15109740306f7f2a7c2173e12072

Re: [PATCH ath-next V15 5/9] wifi: ath12k: fix TX and RX MCS rate configurations in HE mode

[Pradeep Kumar Chitrapu]

On 6/30/2025 7:14 PM, Baochen Qiang wrote:
> 
> 
> On 7/1/2025 9:04 AM, Pradeep Kumar Chitrapu wrote:
>> Currently, the TX and RX MCS rate configurations per peer are
>> reversed when sent to the firmware. As a result, RX MCS rates
>> are configured for TX, and vice versa. This commit rectifies
>> the configuration to match what the firmware expects.
> 
> Please mention that you are rectifying only for AP mode. For STA, current code is good.
Sure..technically I am changing for all modes except STA mode
> 
>>
>> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
>>
>> Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
>> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
> 
> I don't see the need to add my S-O-B here, better drop it.
Sure thanks
> 
>> Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
>> ---
>>   drivers/net/wireless/ath/ath12k/wmi.c | 19 +++++++++++++++++--
>>   drivers/net/wireless/ath/ath12k/wmi.h |  2 ++
>>   2 files changed, 19 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/net/wireless/ath/ath12k/wmi.c b/drivers/net/wireless/ath/ath12k/wmi.c
>> index 6c6354b3e18e..cdf3406302ee 100644
>> --- a/drivers/net/wireless/ath/ath12k/wmi.c
>> +++ b/drivers/net/wireless/ath/ath12k/wmi.c
>> @@ -2183,6 +2183,8 @@ int ath12k_wmi_send_peer_assoc_cmd(struct ath12k *ar,
>>   				   struct ath12k_wmi_peer_assoc_arg *arg)
>>   {
>>   	struct ath12k_wmi_pdev *wmi = ar->wmi;
>> +	struct ath12k_base *ab = ar->ab;
>> +	struct ath12k_link_vif *arvif;
>>   	struct wmi_peer_assoc_complete_cmd *cmd;
>>   	struct ath12k_wmi_vht_rate_set_params *mcs;
>>   	struct ath12k_wmi_he_rate_set_params *he_mcs;
>> @@ -2198,6 +2200,13 @@ int ath12k_wmi_send_peer_assoc_cmd(struct ath12k *ar,
>>   	u16 eml_cap;
>>   	__le32 v;
>>   
>> +	arvif = ath12k_mac_get_arvif(ar, arg->vdev_id);
>> +	if (!arvif) {
>> +		ath12k_warn(ab, "failed to find arvif with vdev id %d\n",
>> +			    arg->vdev_id);
>> +		return -EINVAL;
>> +	}
>> +
>>   	peer_legacy_rates_align = roundup(arg->peer_legacy_rates.num_rates,
>>   					  sizeof(u32));
>>   	peer_ht_rates_align = roundup(arg->peer_ht_rates.num_rates,
>> @@ -2333,8 +2342,14 @@ int ath12k_wmi_send_peer_assoc_cmd(struct ath12k *ar,
>>   		he_mcs->tlv_header = ath12k_wmi_tlv_cmd_hdr(WMI_TAG_HE_RATE_SET,
>>   							    sizeof(*he_mcs));
>>   
>> -		he_mcs->rx_mcs_set = cpu_to_le32(arg->peer_he_rx_mcs_set[i]);
>> -		he_mcs->tx_mcs_set = cpu_to_le32(arg->peer_he_tx_mcs_set[i]);
>> +		if (arvif->ahvif->vdev_type == WMI_VDEV_TYPE_STA) {
>> +			he_mcs->rx_mcs_set = cpu_to_le32(arg->peer_he_rx_mcs_set[i]);
>> +			he_mcs->tx_mcs_set = cpu_to_le32(arg->peer_he_tx_mcs_set[i]);
>> +
>> +		} else {
>> +			he_mcs->rx_mcs_set = cpu_to_le32(arg->peer_he_tx_mcs_set[i]);
>> +			he_mcs->tx_mcs_set = cpu_to_le32(arg->peer_he_rx_mcs_set[i]);
>> +		}
>>   		ptr += sizeof(*he_mcs);
>>   	}
>>   
>> diff --git a/drivers/net/wireless/ath/ath12k/wmi.h b/drivers/net/wireless/ath/ath12k/wmi.h
>> index 0964ca03069a..7ad84624600d 100644
>> --- a/drivers/net/wireless/ath/ath12k/wmi.h
>> +++ b/drivers/net/wireless/ath/ath12k/wmi.h
>> @@ -4162,7 +4162,9 @@ struct ath12k_wmi_vht_rate_set_params {
>>   
>>   struct ath12k_wmi_he_rate_set_params {
>>   	__le32 tlv_header;
>> +	/* MCS at which the peer can receive */
>>   	__le32 rx_mcs_set;
>> +	/* MCS at which the peer can transmit */
>>   	__le32 tx_mcs_set;
>>   } __packed;
>>   
> 

Re: [PATCH ath-next V15 0/9] wifi: ath12k: add MU-MIMO and 160 MHz bandwidth support

[Jeff Johnson]

On 6/30/2025 6:03 PM, Pradeep Kumar Chitrapu wrote:
>   Add support for
> 1. enabling MU-MIMO in HE and EHT modes from hardware
> 2. setting fixed HE rate/GI/LTF
> 3. 160 MHz bandwidth in HE mode
> 4. extended NSS bandwidth support
> 
> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
> 
> changes in v15:
>  - rebased the series after merge conflicts reported
>  patch 4/9:
>  - change the fix to apply for all modes except STA mode as
>    WCN7850 expect it same as before.
> 
> changes in v14:
>  patch 6/9:
>  - cap max_nss using ar->num_tx_chains to fix interop issue caused due
>    to sending nss value 4 when firmware only supports nss value 2.
>  patch 8/9:
>  - Set the default return value to MODE_11AC_VHT160 for 160 MHz
>    to allow STA to connect to the AP even if it does not
>    explicitly indicate 160 MHz bandwidth support.
> 
> changes in v13:
>  - rebase
> 
> changes in v12:
>  - rebase
> 
> changes in v11:
>  patch 1/9:
>   - fix return values in ath12k_mac_set_he_txbf_conf() and
>     ath12k_mac_vif_recalc_sta_he_txbf()
>  patch 6/9:
>   - fix missing he_mcs initialization in ath12k_mac_init_arvif()
> 
> changes in v10:
>  patch 6/9:
>   - use ath12k_ahsta_to_sta()
>   - fix rcu_dereference warning in ath12k_mac_set_bitrate_mask_iter()
>   - change return type for ath12k_mac_validate_fixed_rate_settings()
>   - improve readability by adhering to nl80211 definitions of GI
>     NL80211_TXRATE_DEFAULT_GI. Introduce ath12k_mac_nlgi_to_wmigi()
>     for conversion.
>  patch 7/9:
>   - do not change default MODE_11AC_VHT160 in
>     ath12k_mac_get_phymode_vht() as it breaks clients which do not
>     set VHT_CAP_SUPP_CHAN_WIDTH_160MHZ.
>  patch 8/9:
>   - Use IEEE80211_VHT_CAP_EXT_NSS_BW_MASK along with
>     IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ for determining VHT160
>     phymode.
> 
> changes in v9: rebase on top of master branch with mlo changes
>  patch 1/9 and 2/9:
>   - fetch link_conf using ath12k_mac_get_link_bss_conf()
>     instead of arvif->vif->bss_conf before mlo
>  patch 6/9
>   - fetch mcs/nss values from sta->link[] instead of sta->deflink
>   - fix spelling of 'incompatibility'
>  patch 8/9
>   - replace sta->deflink.addr with arsta->addr in
>     ath12k_peer_assoc_h_vht
>  patch 9/9
>   - replace sta->deflink.rx_nss with link_sta->rx_nss
> 
> changes in v8:
>  - rebase and resolve KASAN warnings reported by Jeff in v7, in patch 6/9.
> 
> Pradeep Kumar Chitrapu (9):
>   wifi: ath12k: push HE MU-MIMO params to hardware
>   wifi: ath12k: push EHT MU-MIMO params to hardware
>   wifi: ath12k: move HE MCS mapper to a separate function
>   wifi: ath12k: generate rx and tx mcs maps for supported HE mcs
>   wifi: ath12k: fix TX and RX MCS rate configurations in HE mode
>   wifi: ath12k: add support for setting fixed HE rate/GI/LTF
>   wifi: ath12k: clean up 80P80 support
>   wifi: ath12k: add support for 160 MHz bandwidth
>   wifi: ath12k: add extended NSS bandwidth support for 160 MHz
> 
>  drivers/net/wireless/ath/ath12k/core.h |    2 +
>  drivers/net/wireless/ath/ath12k/mac.c  | 1144 ++++++++++++++++++++----
>  drivers/net/wireless/ath/ath12k/mac.h  |   17 +
>  drivers/net/wireless/ath/ath12k/wmi.c  |   28 +-
>  drivers/net/wireless/ath/ath12k/wmi.h  |  100 ++-
>  5 files changed, 1069 insertions(+), 222 deletions(-)
> 
> 
> base-commit: c256a94d1b1b15109740306f7f2a7c2173e12072

Since there are lingering questions about the 5/9 patch I plan to take 1-4,6-9

Given that there is ongoing discussion about the 5/9 patch logic in the
context of the ath11k driver, this patch can be posted again separately when
the discussions have concluded and the correct interpretation by firmware is
clear across all chipsets and interface types.

/jeff

Re: (subset) [PATCH ath-next V15 0/9] wifi: ath12k: add MU-MIMO and 160 MHz bandwidth support

[Jeff Johnson]

On Mon, 30 Jun 2025 18:03:59 -0700, Pradeep Kumar Chitrapu wrote:
>   Add support for
> 1. enabling MU-MIMO in HE and EHT modes from hardware
> 2. setting fixed HE rate/GI/LTF
> 3. 160 MHz bandwidth in HE mode
> 4. extended NSS bandwidth support
> 
> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
> Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
> 
> [...]

Applied, thanks!

[1/9] wifi: ath12k: push HE MU-MIMO params to hardware
      commit: 5d6707e88e7fe2d603ad45c5fe7eba096be9533a
[2/9] wifi: ath12k: push EHT MU-MIMO params to hardware
      commit: df8207bc0b4895c18e98a4b084806222b592d9f1
[3/9] wifi: ath12k: move HE MCS mapper to a separate function
      commit: 1eafb8d15d8af39ac7b4d78d69b17f85aa8e00fa
[4/9] wifi: ath12k: generate rx and tx mcs maps for supported HE mcs
      commit: 5ab7479a063d1b557fa59999de701ad8a4624b84
[6/9] wifi: ath12k: add support for setting fixed HE rate/GI/LTF
      commit: 9ad6b169ddef679a64727e3870a6177c78f24b05
[7/9] wifi: ath12k: clean up 80P80 support
      commit: dd25a004fb66c60934fa9572298671c1eb1c06c2
[8/9] wifi: ath12k: add support for 160 MHz bandwidth
      commit: 18ab9d038fadd35d8a4ac5db87ad16dde78f5fdc
[9/9] wifi: ath12k: add extended NSS bandwidth support for 160 MHz
      commit: a82ce08775bc5b50613d48ab7e41b25fc46825af

Best regards,
-- 
Jeff Johnson <jeff.johnson@oss.qualcomm.com>