* [Bridge] using a bridge (setting priority eth0 > ath0)
@ 2009-10-25 0:38 Joachim Schiele
2009-10-27 22:55 ` Nicolas de Pesloüan
0 siblings, 1 reply; 2+ messages in thread
From: Joachim Schiele @ 2009-10-25 0:38 UTC (permalink / raw)
To: bridge
hello,
what i want to do:
having two computers both equipped with:
lspci
01:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit
Ethernet (rev 10)
01:0a.0 Ethernet controller: Atheros Communications Inc. AR5212/AR5213
Multiprotocol MAC/baseband processor (rev 01)
i create two bridges (one on each host)
pc2b ~ # brctl show br0
bridge name bridge id STP enabled interfaces
br0 0000.0040f4a0b037 yes ath0
eth0
and then i set all interfaces up using:
ip l set ath0 up
ip l set eth0 up
ip l set br0 up
i put one ath0 interface into master mode and the other ath0 is a normal
station (client). the connections eth0-eth0 works great, also the ath0-ath0
link works great (tested with and without bridge).
in general everything works, if i either one of the 4 interfaces down
(eth0/eth0/ath0/ath0) stp's work creates a working path in no time.
the issue is - the reason i write to this list however:
when all interfaces are up the data always is going over ath0-ath0 instead of
eth0-eth0. (the wireless lan should be my backup link).
i issues setbridgeprio br0 1 and setbridgeprio br0 10. as well as setpathcost
with various consistent experiments. say one experiment i set all ath0
pathcosts to a value 100 all eth0 to 999.
i don't see any difference when doing the opposite.
any idea?
dmesg added but i don't see anything special there. there was an error once
but i think that might have something todo with the routing loop i caused
(which i resolved with adding setfd with a higher value).
thanks,
joachim schiele
============ pc2 ==============
dmesg
br0: port 2(ath0) entering forwarding state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
eth0: received packet with own address as source address
eth0: received packet with own address as source address
br0: no IPv6 routers present
br0: received tcn bpdu on port 1(eth0)
br0: topology change detected, propagating
br0: port 2(ath0) entering disabled state
br0: port 2(ath0) entering listening state
br0: port 2(ath0) entering learning state
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
ath0: no IPv6 routers present
br0: received tcn bpdu on port 1(eth0)
br0: topology change detected, propagating
br0: port 2(ath0) entering disabled state
br0: port 2(ath0) entering listening state
br0: port 2(ath0) entering learning state
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
ath0: no IPv6 routers present
br0: received tcn bpdu on port 1(eth0)
br0: topology change detected, propagating
ip l
14: ath0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UNKNOWN
link/ether 00:40:f4:a0:b0:37 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP qlen 1000
link/ether 00:40:f4:eb:16:45 brd ff:ff:ff:ff:ff:ff
pc2b ~ # brctl show
bridge name bridge id STP enabled interfaces
br0 0000.0040f4a0b037 yes ath0
eth0
pc2b ~ # brctl showstp br0
br0
bridge id 0000.0040f4a0b037
designated root 0000.0040f4a0b037
root port 0 path cost 0
max age 9.99 bridge max age
9.99
hello time 1.99 bridge hello time
1.99
forward delay 2.99 bridge forward delay
2.99
ageing time 3.99
hello timer 1.49 tcn timer
0.00
topology change timer 0.00 gc timer
1.49
flags
ath0 (2)
port id 0402 state
forwarding
designated root 0000.0040f4a0b037 path cost 999
designated bridge 0000.0040f4a0b037 message age timer
0.00
designated port 0402 forward delay timer
0.00
designated cost 0 hold timer
0.48
flags
eth0 (1)
port id 2801 state
forwarding
designated root 0000.0040f4a0b037 path cost 111
designated bridge 0000.0040f4a0b037 message age timer
0.00
designated port 2801 forward delay timer
0.00
designated cost 0 hold timer
0.48
flags
arp -e
10.0.0.1 ether 00:40:f4:a0:b0:00 C br0
============ pc6 ==============
ip l
17: ath0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UP
link/ether 00:40:f4:a0:b0:00 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP qlen 1000
link/ether 00:40:f4:ec:59:06 brd ff:ff:ff:ff:ff:ff
dmesg
eth0: received packet with own address as source address
eth0: received packet with own address as source address
__ratelimit: 9560 callbacks suppressed
eth0: received packet with own address as source address
eth0: received packet with own address as source address
eth0: received packet with own address as source address
eth0: received packet with own address as source address
eth0: received packet with own address as source address
eth0: received packet with own address as source address
eth0: received packet with own address as source address
eth0: received packet with own address as source address
eth0: received packet with own address as source address
eth0: received packet with own address as source address
br0: port 2(ath0) entering disabled state
__ratelimit: 7851 callbacks suppressed
eth0: received packet with own address as source address
br0: port 2(ath0) entering listening state
br0: port 2(ath0) entering learning state
br0: topology change detected, sending tcn bpdu
br0: port 2(ath0) entering forwarding state
br0: port 2(ath0) entering disabled state
eth0: received packet with own address as source address
br0: port 2(ath0) entering listening state
br0: port 2(ath0) entering learning state
br0: topology change detected, sending tcn bpdu
br0: port 2(ath0) entering forwarding state
br0: port 2(ath0) entering disabled state
eth0: received packet with own address as source address
br0: port 2(ath0) entering listening state
br0: port 2(ath0) entering learning state
br0: topology change detected, sending tcn bpdu
br0: port 2(ath0) entering forwarding state
arp -e
PC2 ether 00:40:f4:a0:b0:37 C br0
pc2b ~ # brctl show
bridge name bridge id STP enabled interfaces
br0 0000.0040f4a0b037 yes ath0
eth0
pc2b ~ # brctl showstp br0
br0
bridge id 0000.0040f4a0b037
designated root 0000.0040f4a0b037
root port 0 path cost 0
max age 9.99 bridge max age
9.99
hello time 1.99 bridge hello time
1.99
forward delay 2.99 bridge forward delay
2.99
ageing time 3.99
hello timer 1.20 tcn timer
0.00
topology change timer 0.00 gc timer
0.20
flags
ath0 (2)
port id 0402 state
forwarding
designated root 0000.0040f4a0b037 path cost 999
designated bridge 0000.0040f4a0b037 message age timer
0.00
designated port 0402 forward delay timer
0.00
designated cost 0 hold timer
0.20
flags
eth0 (1)
port id 2801 state
forwarding
designated root 0000.0040f4a0b037 path cost 111
designated bridge 0000.0040f4a0b037 message age timer
0.00
designated port 2801 forward delay timer
0.00
designated cost 0 hold timer
0.20
flags
^ permalink raw reply [flat|nested] 2+ messages in thread
* Re: [Bridge] using a bridge (setting priority eth0 > ath0)
2009-10-25 0:38 [Bridge] using a bridge (setting priority eth0 > ath0) Joachim Schiele
@ 2009-10-27 22:55 ` Nicolas de Pesloüan
0 siblings, 0 replies; 2+ messages in thread
From: Nicolas de Pesloüan @ 2009-10-27 22:55 UTC (permalink / raw)
To: Joachim Schiele; +Cc: bridge
Joachim Schiele wrote:
> hello,
>
> what i want to do:
> having two computers both equipped with:
> lspci
> 01:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit
> Ethernet (rev 10)
> 01:0a.0 Ethernet controller: Atheros Communications Inc. AR5212/AR5213
> Multiprotocol MAC/baseband processor (rev 01)
For this kind of setup, if might be easier to setup a bonding interface, instead of a bridge interface.
With a bonding setup, you can define a primary adapter that will be used when available.
Nicolas.
>
> i create two bridges (one on each host)
> pc2b ~ # brctl show br0
> bridge name bridge id STP enabled interfaces
> br0 0000.0040f4a0b037 yes ath0
> eth0
>
> and then i set all interfaces up using:
> ip l set ath0 up
> ip l set eth0 up
> ip l set br0 up
>
> i put one ath0 interface into master mode and the other ath0 is a normal
> station (client). the connections eth0-eth0 works great, also the ath0-ath0
> link works great (tested with and without bridge).
>
> in general everything works, if i either one of the 4 interfaces down
> (eth0/eth0/ath0/ath0) stp's work creates a working path in no time.
>
> the issue is - the reason i write to this list however:
> when all interfaces are up the data always is going over ath0-ath0 instead of
> eth0-eth0. (the wireless lan should be my backup link).
>
> i issues setbridgeprio br0 1 and setbridgeprio br0 10. as well as setpathcost
> with various consistent experiments. say one experiment i set all ath0
> pathcosts to a value 100 all eth0 to 999.
> i don't see any difference when doing the opposite.
>
> any idea?
>
> dmesg added but i don't see anything special there. there was an error once
> but i think that might have something todo with the routing loop i caused
> (which i resolved with adding setfd with a higher value).
>
> thanks,
> joachim schiele
>
>
>
>
>
> ============ pc2 ==============
> dmesg
> br0: port 2(ath0) entering forwarding state
> br0: topology change detected, propagating
> br0: port 1(eth0) entering forwarding state
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> br0: no IPv6 routers present
> br0: received tcn bpdu on port 1(eth0)
> br0: topology change detected, propagating
> br0: port 2(ath0) entering disabled state
> br0: port 2(ath0) entering listening state
> br0: port 2(ath0) entering learning state
> br0: topology change detected, propagating
> br0: port 2(ath0) entering forwarding state
> ath0: no IPv6 routers present
> br0: received tcn bpdu on port 1(eth0)
> br0: topology change detected, propagating
> br0: port 2(ath0) entering disabled state
> br0: port 2(ath0) entering listening state
> br0: port 2(ath0) entering learning state
> br0: topology change detected, propagating
> br0: port 2(ath0) entering forwarding state
> ath0: no IPv6 routers present
> br0: received tcn bpdu on port 1(eth0)
> br0: topology change detected, propagating
>
> ip l
> 14: ath0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc noqueue
> state UNKNOWN
> link/ether 00:40:f4:a0:b0:37 brd ff:ff:ff:ff:ff:ff
> 3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state UP qlen 1000
> link/ether 00:40:f4:eb:16:45 brd ff:ff:ff:ff:ff:ff
>
> pc2b ~ # brctl show
> bridge name bridge id STP enabled interfaces
> br0 0000.0040f4a0b037 yes ath0
> eth0
> pc2b ~ # brctl showstp br0
> br0
> bridge id 0000.0040f4a0b037
> designated root 0000.0040f4a0b037
> root port 0 path cost 0
> max age 9.99 bridge max age
> 9.99
> hello time 1.99 bridge hello time
> 1.99
> forward delay 2.99 bridge forward delay
> 2.99
> ageing time 3.99
> hello timer 1.49 tcn timer
> 0.00
> topology change timer 0.00 gc timer
> 1.49
> flags
>
>
> ath0 (2)
> port id 0402 state
> forwarding
> designated root 0000.0040f4a0b037 path cost 999
> designated bridge 0000.0040f4a0b037 message age timer
> 0.00
> designated port 0402 forward delay timer
> 0.00
> designated cost 0 hold timer
> 0.48
> flags
>
> eth0 (1)
> port id 2801 state
> forwarding
> designated root 0000.0040f4a0b037 path cost 111
> designated bridge 0000.0040f4a0b037 message age timer
> 0.00
> designated port 2801 forward delay timer
> 0.00
> designated cost 0 hold timer
> 0.48
> flags
>
> arp -e
> 10.0.0.1 ether 00:40:f4:a0:b0:00 C br0
>
>
>
>
>
>
>
>
>
> ============ pc6 ==============
> ip l
> 17: ath0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc noqueue
> state UP
> link/ether 00:40:f4:a0:b0:00 brd ff:ff:ff:ff:ff:ff
> 3: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
> state UP qlen 1000
> link/ether 00:40:f4:ec:59:06 brd ff:ff:ff:ff:ff:ff
>
> dmesg
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> __ratelimit: 9560 callbacks suppressed
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> eth0: received packet with own address as source address
> br0: port 2(ath0) entering disabled state
> __ratelimit: 7851 callbacks suppressed
> eth0: received packet with own address as source address
> br0: port 2(ath0) entering listening state
> br0: port 2(ath0) entering learning state
> br0: topology change detected, sending tcn bpdu
> br0: port 2(ath0) entering forwarding state
> br0: port 2(ath0) entering disabled state
> eth0: received packet with own address as source address
> br0: port 2(ath0) entering listening state
> br0: port 2(ath0) entering learning state
> br0: topology change detected, sending tcn bpdu
> br0: port 2(ath0) entering forwarding state
> br0: port 2(ath0) entering disabled state
> eth0: received packet with own address as source address
> br0: port 2(ath0) entering listening state
> br0: port 2(ath0) entering learning state
> br0: topology change detected, sending tcn bpdu
> br0: port 2(ath0) entering forwarding state
>
> arp -e
> PC2 ether 00:40:f4:a0:b0:37 C br0
>
> pc2b ~ # brctl show
> bridge name bridge id STP enabled interfaces
> br0 0000.0040f4a0b037 yes ath0
> eth0
> pc2b ~ # brctl showstp br0
> br0
> bridge id 0000.0040f4a0b037
> designated root 0000.0040f4a0b037
> root port 0 path cost 0
> max age 9.99 bridge max age
> 9.99
> hello time 1.99 bridge hello time
> 1.99
> forward delay 2.99 bridge forward delay
> 2.99
> ageing time 3.99
> hello timer 1.20 tcn timer
> 0.00
> topology change timer 0.00 gc timer
> 0.20
> flags
>
>
> ath0 (2)
> port id 0402 state
> forwarding
> designated root 0000.0040f4a0b037 path cost 999
> designated bridge 0000.0040f4a0b037 message age timer
> 0.00
> designated port 0402 forward delay timer
> 0.00
> designated cost 0 hold timer
> 0.20
> flags
>
> eth0 (1)
> port id 2801 state
> forwarding
> designated root 0000.0040f4a0b037 path cost 111
> designated bridge 0000.0040f4a0b037 message age timer
> 0.00
> designated port 2801 forward delay timer
> 0.00
> designated cost 0 hold timer
> 0.20
> flags
> _______________________________________________
> Bridge mailing list
> Bridge@lists.linux-foundation.org
> https://lists.linux-foundation.org/mailman/listinfo/bridge
>
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2009-10-27 22:55 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-10-25 0:38 [Bridge] using a bridge (setting priority eth0 > ath0) Joachim Schiele
2009-10-27 22:55 ` Nicolas de Pesloüan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox