[Buildroot] [PATCH 1/1] rpi-firmware: do not rename startup files

[Yann E. MORIN <yann.morin.1998@free.fr>]

St?phane, All,

Please wrap your commit logs properly, at a 72-or-so boundary.

On 2020-06-24 13:50 +0200, St?phane Veyret spake thusly:
> Bug: 13026
> 
> When booting, a Raspberry Pi will load the appropriate start files, depending on the provided configuration. For example, if the config.txt file contains:
> gpu_mem=16
> the board will automatically load the cut-down startup files (start_cd.elf and fixup_cd.dat on non-Rpi4).

So, the startup file loaded depends on the amount of memory the user
enables, and maybe other configurations, who knows?

This somewhat goes directly agains the user selecting a specific startup
file to use. See below...

> Unfortunately, even when the appropriate version is selected in the configuration menu (in this example, BR2_PACKAGE_RPI_FIRMWARE_BOOT="_cd") if the rpi-firmware makefile takes the good files, it renames them to non-qualified, i.e. start.elf and fixup.dat. But as these are not the files searched by the Raspberry Pi, the board will not start.
> 
> Signed-off-by: St?phane Veyret <sveyret@gmail.com>
> ---
>  package/rpi-firmware/rpi-firmware.mk | 10 +++++-----
>  1 file changed, 5 insertions(+), 5 deletions(-)
> 
> diff --git a/package/rpi-firmware/rpi-firmware.mk b/package/rpi-firmware/rpi-firmware.mk
> index 6ad67ab0e5..2f4b2b05bf 100644
> --- a/package/rpi-firmware/rpi-firmware.mk
> +++ b/package/rpi-firmware/rpi-firmware.mk
> @@ -44,14 +44,14 @@ endif # INSTALL_VCDBG
>  ifeq ($(BR2_PACKAGE_RPI_FIRMWARE_VARIANT_PI4),y)
>  # bootcode.bin is not used on rpi4, because it has been replaced by boot code in the onboard EEPROM
>  define RPI_FIRMWARE_INSTALL_BOOT
> -	$(INSTALL) -D -m 0644 $(@D)/boot/start4$(BR2_PACKAGE_RPI_FIRMWARE_BOOT).elf $(BINARIES_DIR)/rpi-firmware/start4.elf
> -	$(INSTALL) -D -m 0644 $(@D)/boot/fixup4$(BR2_PACKAGE_RPI_FIRMWARE_BOOT).dat $(BINARIES_DIR)/rpi-firmware/fixup4.dat
> +	$(INSTALL) -D -m 0644 $(@D)/boot/start4$(BR2_PACKAGE_RPI_FIRMWARE_BOOT).elf $(BINARIES_DIR)/rpi-firmware/
> +	$(INSTALL) -D -m 0644 $(@D)/boot/fixup4$(BR2_PACKAGE_RPI_FIRMWARE_BOOT).dat $(BINARIES_DIR)/rpi-firmware/
>  endef
>  else
>  define RPI_FIRMWARE_INSTALL_BOOT
> -	$(INSTALL) -D -m 0644 $(@D)/boot/bootcode.bin $(BINARIES_DIR)/rpi-firmware/bootcode.bin
> -	$(INSTALL) -D -m 0644 $(@D)/boot/start$(BR2_PACKAGE_RPI_FIRMWARE_BOOT).elf $(BINARIES_DIR)/rpi-firmware/start.elf
> -	$(INSTALL) -D -m 0644 $(@D)/boot/fixup$(BR2_PACKAGE_RPI_FIRMWARE_BOOT).dat $(BINARIES_DIR)/rpi-firmware/fixup.dat
> +	$(INSTALL) -D -m 0644 $(@D)/boot/bootcode.bin $(BINARIES_DIR)/rpi-firmware/
> +	$(INSTALL) -D -m 0644 $(@D)/boot/start$(BR2_PACKAGE_RPI_FIRMWARE_BOOT).elf $(BINARIES_DIR)/rpi-firmware/
> +	$(INSTALL) -D -m 0644 $(@D)/boot/fixup$(BR2_PACKAGE_RPI_FIRMWARE_BOOT).dat $(BINARIES_DIR)/rpi-firmware/

I think we should instead force the name of the startup files in the
config.txt (in package/rpi-firmware/config.txt):

    start_file=start.elf
    fixup_file=fixup.dat

Which will always be exactly what to load. I was pretty farn sure that's
what we already did, but I remembered wrong...

See: https://github.com/raspberrypi/documentation/blob/master/configuration/config-txt/boot.md

Can you respin a patch to that effect, please?

Regards,
Yann E. MORIN.

Regards,
Yann E. MORIN.

>  endef
>  endif
>  
> -- 
> 2.26.2
> 
> _______________________________________________
> buildroot mailing list
> buildroot at busybox.net
> http://lists.busybox.net/mailman/listinfo/buildroot

-- 
.-----------------.--------------------.------------------.--------------------.
|  Yann E. MORIN  | Real-Time Embedded | /"\ ASCII RIBBON | Erics' conspiracy: |
| +33 662 376 056 | Software  Designer | \ / CAMPAIGN     |  ___               |
| +33 561 099 427 `------------.-------:  X  AGAINST      |  \e/  There is no  |
| http://ymorin.is-a-geek.org/ | _/*\_ | / \ HTML MAIL    |   v   conspiracy.  |
'------------------------------^-------^------------------^--------------------'