* [Buildroot] [PATCH 1/1] board/zynqmp/post-image.sh: Don't insist on a xilinx/ prefix for .dts files.
@ 2023-02-01 19:59 Graeme Smecher
2023-02-01 21:52 ` Luca Ceresoli via buildroot
2023-02-05 12:20 ` Thomas Petazzoni via buildroot
0 siblings, 2 replies; 6+ messages in thread
From: Graeme Smecher @ 2023-02-01 19:59 UTC (permalink / raw)
To: buildroot; +Cc: Graeme Smecher, Luca Ceresoli, Neal Frager
If using BR2_LINUX_KERNEL_CUSTOM_DTS_PATH to copy .dts files from
buildroot into the linux tree, these .dts files are copied to
arch/arm64/boot. Unfortunately, the post-image.sh script expects to find
them in arch/arm64/boot/xilinx.
This patch does not require the xilinx/ prefix to be present when
symlinking the device-tree to system.dtb where u-boot expects to find
it.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
---
board/zynqmp/post-image.sh | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/board/zynqmp/post-image.sh b/board/zynqmp/post-image.sh
index ed6dbe188c..c5de2db820 100755
--- a/board/zynqmp/post-image.sh
+++ b/board/zynqmp/post-image.sh
@@ -5,7 +5,7 @@
# devicetree listed in the config.
FIRST_DT=$(sed -nr \
- -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
+ -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="(xilinx/)?([-_/[:alnum:]\\.]*).*"$|\2|p' \
${BR2_CONFIG})
[ -z "${FIRST_DT}" ] || ln -fs ${FIRST_DT}.dtb ${BINARIES_DIR}/system.dtb
--
2.35.1
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [Buildroot] [PATCH 1/1] board/zynqmp/post-image.sh: Don't insist on a xilinx/ prefix for .dts files.
2023-02-01 19:59 [Buildroot] [PATCH 1/1] board/zynqmp/post-image.sh: Don't insist on a xilinx/ prefix for .dts files Graeme Smecher
@ 2023-02-01 21:52 ` Luca Ceresoli via buildroot
2023-02-01 22:16 ` Graeme Smecher
2023-02-05 12:20 ` Thomas Petazzoni via buildroot
1 sibling, 1 reply; 6+ messages in thread
From: Luca Ceresoli via buildroot @ 2023-02-01 21:52 UTC (permalink / raw)
To: Graeme Smecher; +Cc: Neal Frager, buildroot
Hi Graeme,
On Wed, 1 Feb 2023 11:59:56 -0800
Graeme Smecher <gsmecher@threespeedlogic.com> wrote:
> If using BR2_LINUX_KERNEL_CUSTOM_DTS_PATH to copy .dts files from
> buildroot into the linux tree, these .dts files are copied to
> arch/arm64/boot. Unfortunately, the post-image.sh script expects to find
> them in arch/arm64/boot/xilinx.
>
> This patch does not require the xilinx/ prefix to be present when
> symlinking the device-tree to system.dtb where u-boot expects to find
> it.
>
> Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
> ---
> board/zynqmp/post-image.sh | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/board/zynqmp/post-image.sh b/board/zynqmp/post-image.sh
> index ed6dbe188c..c5de2db820 100755
> --- a/board/zynqmp/post-image.sh
> +++ b/board/zynqmp/post-image.sh
> @@ -5,7 +5,7 @@
> # devicetree listed in the config.
>
> FIRST_DT=$(sed -nr \
> - -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
> + -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="(xilinx/)?([-_/[:alnum:]\\.]*).*"$|\2|p' \
I think the following simpler change would also work. Can you check
that please?
- -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
+ -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="([-_/[:alnum:]\\.]*).*"$|\2|p' \
--
Luca Ceresoli, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Buildroot] [PATCH 1/1] board/zynqmp/post-image.sh: Don't insist on a xilinx/ prefix for .dts files.
2023-02-01 21:52 ` Luca Ceresoli via buildroot
@ 2023-02-01 22:16 ` Graeme Smecher
2023-02-02 8:21 ` Luca Ceresoli via buildroot
0 siblings, 1 reply; 6+ messages in thread
From: Graeme Smecher @ 2023-02-01 22:16 UTC (permalink / raw)
To: Luca Ceresoli; +Cc: Neal Frager, buildroot
Hi Luca,
On 2023-02-01 13:52, Luca Ceresoli wrote:
> Hi Graeme,
>
> On Wed, 1 Feb 2023 11:59:56 -0800
> Graeme Smecher <gsmecher@threespeedlogic.com> wrote:
>
>> If using BR2_LINUX_KERNEL_CUSTOM_DTS_PATH to copy .dts files from
>> buildroot into the linux tree, these .dts files are copied to
>> arch/arm64/boot. Unfortunately, the post-image.sh script expects to find
>> them in arch/arm64/boot/xilinx.
>>
>> This patch does not require the xilinx/ prefix to be present when
>> symlinking the device-tree to system.dtb where u-boot expects to find
>> it.
>>
>> Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
>> ---
>> board/zynqmp/post-image.sh | 2 +-
>> 1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/board/zynqmp/post-image.sh b/board/zynqmp/post-image.sh
>> index ed6dbe188c..c5de2db820 100755
>> --- a/board/zynqmp/post-image.sh
>> +++ b/board/zynqmp/post-image.sh
>> @@ -5,7 +5,7 @@
>> # devicetree listed in the config.
>>
>> FIRST_DT=$(sed -nr \
>> - -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
>> + -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="(xilinx/)?([-_/[:alnum:]\\.]*).*"$|\2|p' \
>
> I think the following simpler change would also work. Can you check
> that please?
>
> - -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
> + -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="([-_/[:alnum:]\\.]*).*"$|\2|p' \
Assuming you intended \1, not \2 here - this suggestion breaks behaviour for a couple of defconfigs in the tree. If I run the ZCU106 defconfig through this regexp, I get:
$ cat configs/zynqmp_zcu106_defconfig | sed -nr -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="([-_/[:alnum:]\\.]*).*"$|\1|p'
xilinx/zynqmp-zcu106-revA
...this creates a dangling symlink in output/images (system.dtb -> xilinx/zynqmp-zcu106-revA.dtb).
The right behaviour is to strip any prefixes that exist, without requiring any. Something like:
- -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
+ -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="(.*/)?([-_/[:alnum:]\\.]*).*"$|\2|p' \
This is less Xilinx-specific, although it seems a tad greedy.
best,
Graeme
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Buildroot] [PATCH 1/1] board/zynqmp/post-image.sh: Don't insist on a xilinx/ prefix for .dts files.
2023-02-01 22:16 ` Graeme Smecher
@ 2023-02-02 8:21 ` Luca Ceresoli via buildroot
2023-02-02 13:40 ` Frager, Neal via buildroot
0 siblings, 1 reply; 6+ messages in thread
From: Luca Ceresoli via buildroot @ 2023-02-02 8:21 UTC (permalink / raw)
To: Graeme Smecher; +Cc: Neal Frager, buildroot
Hi Graeme,
On Wed, 1 Feb 2023 14:16:47 -0800
Graeme Smecher <gsmecher@threespeedlogic.com> wrote:
> Hi Luca,
>
> On 2023-02-01 13:52, Luca Ceresoli wrote:
> > Hi Graeme,
> >
> > On Wed, 1 Feb 2023 11:59:56 -0800
> > Graeme Smecher <gsmecher@threespeedlogic.com> wrote:
> >
> >> If using BR2_LINUX_KERNEL_CUSTOM_DTS_PATH to copy .dts files from
> >> buildroot into the linux tree, these .dts files are copied to
> >> arch/arm64/boot. Unfortunately, the post-image.sh script expects to find
> >> them in arch/arm64/boot/xilinx.
> >>
> >> This patch does not require the xilinx/ prefix to be present when
> >> symlinking the device-tree to system.dtb where u-boot expects to find
> >> it.
> >>
> >> Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
> >> ---
> >> board/zynqmp/post-image.sh | 2 +-
> >> 1 file changed, 1 insertion(+), 1 deletion(-)
> >>
> >> diff --git a/board/zynqmp/post-image.sh b/board/zynqmp/post-image.sh
> >> index ed6dbe188c..c5de2db820 100755
> >> --- a/board/zynqmp/post-image.sh
> >> +++ b/board/zynqmp/post-image.sh
> >> @@ -5,7 +5,7 @@
> >> # devicetree listed in the config.
> >>
> >> FIRST_DT=$(sed -nr \
> >> - -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
> >> + -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="(xilinx/)?([-_/[:alnum:]\\.]*).*"$|\2|p' \
> >
> > I think the following simpler change would also work. Can you check
> > that please?
> >
> > - -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
> > + -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="([-_/[:alnum:]\\.]*).*"$|\2|p' \
>
> Assuming you intended \1, not \2 here - this suggestion breaks behaviour for a couple of defconfigs in the tree. If I run the ZCU106 defconfig through this regexp, I get:
>
> $ cat configs/zynqmp_zcu106_defconfig | sed -nr -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="([-_/[:alnum:]\\.]*).*"$|\1|p'
> xilinx/zynqmp-zcu106-revA
>
> ...this creates a dangling symlink in output/images (system.dtb -> xilinx/zynqmp-zcu106-revA.dtb).
Right.
> The right behaviour is to strip any prefixes that exist, without requiring any. Something like:
>
> - -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
> + -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="(.*/)?([-_/[:alnum:]\\.]*).*"$|\2|p' \
>
> This is less Xilinx-specific, although it seems a tad greedy.
Yes, better keeping the xilinx prefix as this is a xilinx-specific
script anyway.
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
--
Luca Ceresoli, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Buildroot] [PATCH 1/1] board/zynqmp/post-image.sh: Don't insist on a xilinx/ prefix for .dts files.
2023-02-02 8:21 ` Luca Ceresoli via buildroot
@ 2023-02-02 13:40 ` Frager, Neal via buildroot
0 siblings, 0 replies; 6+ messages in thread
From: Frager, Neal via buildroot @ 2023-02-02 13:40 UTC (permalink / raw)
To: Luca Ceresoli, Graeme Smecher; +Cc: buildroot@buildroot.org
Hi Graeme,
> Hi Luca,
>
> On 2023-02-01 13:52, Luca Ceresoli wrote:
> > Hi Graeme,
> >
> > On Wed, 1 Feb 2023 11:59:56 -0800
> > Graeme Smecher <gsmecher@threespeedlogic.com> wrote:
> >
> >> If using BR2_LINUX_KERNEL_CUSTOM_DTS_PATH to copy .dts files from
> >> buildroot into the linux tree, these .dts files are copied to
> >> arch/arm64/boot. Unfortunately, the post-image.sh script expects to
> >> find them in arch/arm64/boot/xilinx.
> >>
> >> This patch does not require the xilinx/ prefix to be present when
> >> symlinking the device-tree to system.dtb where u-boot expects to
> >> find it.
> >>
> >> Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
> >> ---
> >> board/zynqmp/post-image.sh | 2 +-
> >> 1 file changed, 1 insertion(+), 1 deletion(-)
> >>
> >> diff --git a/board/zynqmp/post-image.sh
> >> b/board/zynqmp/post-image.sh index ed6dbe188c..c5de2db820 100755
> >> --- a/board/zynqmp/post-image.sh
> >> +++ b/board/zynqmp/post-image.sh
> >> @@ -5,7 +5,7 @@
> >> # devicetree listed in the config.
> >>
> >> FIRST_DT=$(sed -nr \
> >> - -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
> >> + -e
> >> + 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="(xilinx/)?([-_/[:alnum:]\\.
> >> + ]*).*"$|\2|p' \
> >
> > I think the following simpler change would also work. Can you check
> > that please?
> >
> > - -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
> > + -e
> > + 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="([-_/[:alnum:]\\.]*).*"$|\2|
> > + p' \
>
> Assuming you intended \1, not \2 here - this suggestion breaks behaviour for a couple of defconfigs in the tree. If I run the ZCU106 defconfig through this regexp, I get:
>
> $ cat configs/zynqmp_zcu106_defconfig | sed -nr -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="([-_/[:alnum:]\\.]*).*"$|\1|p'
> xilinx/zynqmp-zcu106-revA
>
> ...this creates a dangling symlink in output/images (system.dtb -> xilinx/zynqmp-zcu106-revA.dtb).
> Right.
> The right behaviour is to strip any prefixes that exist, without requiring any. Something like:
>
> - -e 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="xilinx/([-_/[:alnum:]\\.]*).*"$|\1|p' \
> + -e
> + 's|^BR2_LINUX_KERNEL_INTREE_DTS_NAME="(.*/)?([-_/[:alnum:]\\.]*).*"$
> + |\2|p' \
>
> This is less Xilinx-specific, although it seems a tad greedy.
> Yes, better keeping the xilinx prefix as this is a xilinx-specific script anyway.
> Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Thank you for your patch.
Reviewed-by: Neal Frager <neal.frager@amd.com>
Best regards,
Neal Frager
AMD
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Buildroot] [PATCH 1/1] board/zynqmp/post-image.sh: Don't insist on a xilinx/ prefix for .dts files.
2023-02-01 19:59 [Buildroot] [PATCH 1/1] board/zynqmp/post-image.sh: Don't insist on a xilinx/ prefix for .dts files Graeme Smecher
2023-02-01 21:52 ` Luca Ceresoli via buildroot
@ 2023-02-05 12:20 ` Thomas Petazzoni via buildroot
1 sibling, 0 replies; 6+ messages in thread
From: Thomas Petazzoni via buildroot @ 2023-02-05 12:20 UTC (permalink / raw)
To: Graeme Smecher; +Cc: Neal Frager, Luca Ceresoli, buildroot
On Wed, 1 Feb 2023 11:59:56 -0800
Graeme Smecher <gsmecher@threespeedlogic.com> wrote:
> If using BR2_LINUX_KERNEL_CUSTOM_DTS_PATH to copy .dts files from
> buildroot into the linux tree, these .dts files are copied to
> arch/arm64/boot. Unfortunately, the post-image.sh script expects to find
> them in arch/arm64/boot/xilinx.
>
> This patch does not require the xilinx/ prefix to be present when
> symlinking the device-tree to system.dtb where u-boot expects to find
> it.
>
> Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
> ---
> board/zynqmp/post-image.sh | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
Applied to master, thanks.
Thomas
--
Thomas Petazzoni, CTO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2023-02-05 12:21 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2023-02-01 19:59 [Buildroot] [PATCH 1/1] board/zynqmp/post-image.sh: Don't insist on a xilinx/ prefix for .dts files Graeme Smecher
2023-02-01 21:52 ` Luca Ceresoli via buildroot
2023-02-01 22:16 ` Graeme Smecher
2023-02-02 8:21 ` Luca Ceresoli via buildroot
2023-02-02 13:40 ` Frager, Neal via buildroot
2023-02-05 12:20 ` Thomas Petazzoni via buildroot
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox