* [Buildroot] [PATCH 1/2] board/orangepi/orangepi-zero3: add SPI-NOR image support
@ 2026-09-25 16:52 Vladimir Savelev
2026-09-25 16:52 ` [Buildroot] [PATCH 2/2] board/orangepi/orangepi-zero2w, orangepi-zero3: set the hostname Vladimir Savelev
0 siblings, 1 reply; 3+ messages in thread
From: Vladimir Savelev @ 2026-09-25 16:52 UTC (permalink / raw)
To: buildroot; +Cc: Marcin Niestroj, Vladimir Savelev, Sergey Matyukevich
The board can boot from its 16 MiB SPI-NOR flash in addition to the SD
card. Add the board files needed to build the SPI-NOR image, leaving the
existing SD card image unchanged.
The SPI-NOR image is assembled with genimage, like the Zero 2W does:
- genimage-spi.cfg describes the raw flash layout (U-Boot, FIT kernel
and squashfs rootfs at fixed offsets, no partition table) and is fed
to the generic genimage wrapper;
- post-image.sh LZMA-compresses the kernel, because the uncompressed
Image does not fit the 5376K kernel partition, wraps the kernel and
the DTB into a FIT image, and then assembles both the SD card and the
SPI-NOR images;
- linux.fragment trims the generic arm64 defconfig so that the
compressed kernel fits in the 5376K partition, and linux-net.fragment
enables the board's on-board Gigabit Ethernet (emac0 + Motorcomm
PHY);
- uboot.fragment sets CONFIG_BOOTCOMMAND to boot the FIT from SPI and
fall back to the default distro boot (SD card), so that the same
U-Boot boots both images.
Both images are built by the same defconfig; the SPI-NOR image uses the
squashfs rootfs, while the SD card image keeps the ext2 rootfs.
Signed-off-by: Vladimir Savelev <anykey196@gmail.com>
---
board/orangepi/orangepi-zero3/fit.its | 38 ++
.../orangepi/orangepi-zero3/genimage-spi.cfg | 42 ++
.../orangepi-zero3/linux-net.fragment | 8 +
board/orangepi/orangepi-zero3/linux.fragment | 567 ++++++++++++++++++
board/orangepi/orangepi-zero3/post-image.sh | 34 ++
board/orangepi/orangepi-zero3/uboot.fragment | 6 +
configs/orangepi_zero3_defconfig | 8 +-
7 files changed, 701 insertions(+), 2 deletions(-)
create mode 100644 board/orangepi/orangepi-zero3/fit.its
create mode 100644 board/orangepi/orangepi-zero3/genimage-spi.cfg
create mode 100644 board/orangepi/orangepi-zero3/linux-net.fragment
create mode 100644 board/orangepi/orangepi-zero3/linux.fragment
create mode 100755 board/orangepi/orangepi-zero3/post-image.sh
create mode 100644 board/orangepi/orangepi-zero3/uboot.fragment
diff --git a/board/orangepi/orangepi-zero3/fit.its b/board/orangepi/orangepi-zero3/fit.its
new file mode 100644
index 0000000000..cdd5afe05c
--- /dev/null
+++ b/board/orangepi/orangepi-zero3/fit.its
@@ -0,0 +1,38 @@
+/dts-v1/;
+
+/ {
+ description = "OrangePi Zero 3 - Linux kernel + FDT (SPI-NOR)";
+ #address-cells = <1>;
+
+ images {
+ kernel {
+ description = "Linux kernel";
+ data = /incbin/("kernel.lzma");
+ type = "kernel";
+ arch = "arm64";
+ os = "linux";
+ compression = "lzma";
+ load = <0x41000000>;
+ entry = <0x41000000>;
+ };
+
+ fdt {
+ description = "OrangePi Zero 3 device tree";
+ data = /incbin/("dtb.bin");
+ type = "flat_dt";
+ arch = "arm64";
+ compression = "none";
+ load = <0x43000000>;
+ };
+ };
+
+ configurations {
+ default = "config";
+
+ config {
+ description = "OrangePi Zero 3";
+ kernel = "kernel";
+ fdt = "fdt";
+ };
+ };
+};
diff --git a/board/orangepi/orangepi-zero3/genimage-spi.cfg b/board/orangepi/orangepi-zero3/genimage-spi.cfg
new file mode 100644
index 0000000000..59dba5e202
--- /dev/null
+++ b/board/orangepi/orangepi-zero3/genimage-spi.cfg
@@ -0,0 +1,42 @@
+# OrangePi Zero 3 - SPI-NOR image (16 MiB, zb25vq128).
+#
+# The layout is dictated by the U-Boot environment in
+# board/orangepi/orangepi-zero2w/uboot.fragment: the mtdparts/bootcmd there use
+# the very same offsets, so both files must be kept in sync.
+#
+# u-boot @ 0 (896K)
+# kernel @ 896K (5376K) FIT: LZMA-compressed kernel + DTB
+# rootfs @ 6272K (10112K) squashfs (XZ)
+#
+# The kernel partition only needs to hold the FIT (~4.8 MiB); the rest of the
+# 16 MiB is given to the rootfs, which carries WiFi (iwd), dropbear and the
+# local credentials.
+
+flash nor-16M-256 {
+ pebsize = 4K
+ numpebs = 4K
+ minimum-io-unit-size = 256
+}
+
+image spi.img {
+ flash {
+ }
+ flashtype = "nor-16M-256"
+
+ partition u-boot {
+ image = "u-boot-sunxi-with-spl.bin"
+ size = 896K
+ }
+
+ partition kernel {
+ image = "fit.itb"
+ offset = 896K
+ size = 5376K
+ }
+
+ partition rootfs {
+ image = "rootfs.squashfs"
+ offset = 6272K
+ size = 10112K
+ }
+}
diff --git a/board/orangepi/orangepi-zero3/linux-net.fragment b/board/orangepi/orangepi-zero3/linux-net.fragment
new file mode 100644
index 0000000000..7d1c59c943
--- /dev/null
+++ b/board/orangepi/orangepi-zero3/linux-net.fragment
@@ -0,0 +1,8 @@
+# Zero 3 networking on top of the trimmed kernel (linux.fragment disables
+# Ethernet): the board has an on-board Gigabit PHY (Motorcomm YT8531) on emac0.
+CONFIG_ETHERNET=y
+CONFIG_NET_VENDOR_STMICRO=y
+CONFIG_STMMAC_ETH=y
+CONFIG_STMMAC_PLATFORM=y
+CONFIG_DWMAC_SUN8I=y
+CONFIG_MOTORCOMM_PHY=y
diff --git a/board/orangepi/orangepi-zero3/linux.fragment b/board/orangepi/orangepi-zero3/linux.fragment
new file mode 100644
index 0000000000..df52d70141
--- /dev/null
+++ b/board/orangepi/orangepi-zero3/linux.fragment
@@ -0,0 +1,567 @@
+# Kernel fragment for the OrangePi Zero 2W 16 MiB SPI-NOR image.
+#
+# The generic arm64 defconfig is far too large for the 6400K kernel partition,
+# so the heaviest unused subsystems are disabled here to keep the
+# LZMA-compressed kernel within that budget. The filesystems used on the
+# board (squashfs for the SPI image, ext4 for the SD card, overlayfs for the
+# writable overlay) are enabled.
+
+# --- Filesystems and MTD used on the board ---
+CONFIG_SQUASHFS_XZ=y
+CONFIG_OVERLAY_FS=y
+CONFIG_MTD_CMDLINE_PARTS=y
+
+# --- Heavy unused subsystems ---
+# CONFIG_DRM is not set
+# CONFIG_DRM_SUN4I is not set
+# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+# CONFIG_FRAMEBUFFER_CONSOLE is not set
+# CONFIG_MEDIA_SUPPORT is not set
+# CONFIG_VIDEO_DEV is not set
+# CONFIG_SOUND is not set
+# CONFIG_SND is not set
+# CONFIG_SOUNDWIRE is not set
+# CONFIG_BT is not set
+# CONFIG_LEDS_TRIGGER_ACTS_RL is not set
+
+# --- Filesystems not used on an SPI flash board ---
+# CONFIG_BTRFS_FS is not set
+# CONFIG_UBIFS_FS is not set
+# CONFIG_VFAT_FS is not set
+# CONFIG_FAT_FS is not set
+
+# --- Network filesystems ---
+# CONFIG_NFS_FS is not set
+# CONFIG_9P_FS is not set
+# CONFIG_NFS_V4 is not set
+
+# --- Network protocol extras / big NICs ---
+# CONFIG_BRIDGE is not set
+# CONFIG_NET_DSA is not set
+# CONFIG_INTEGRITY is not set
+
+# --- Storage controllers not present on H618 ---
+# CONFIG_ATA is not set
+# CONFIG_SCSI is not set
+# CONFIG_NVME_CORE is not set
+# CONFIG_MMC_DW is not set
+# CONFIG_MMC_DW_EXYNOS is not set
+# CONFIG_MMC_DW_PLTFM is not set
+# CONFIG_MMC_DW_HI3798CV200 is not set
+# CONFIG_MMC_SDHCI is not set
+# CONFIG_MMC_SDHCI_PLTFM is not set
+# CONFIG_MMC_SDHCI_OF_ESD is not set
+# CONFIG_MMC_SDHCI_OF_DWCMSHC is not set
+
+# --- Misc heavy stuff ---
+# CONFIG_INPUT is not set
+# CONFIG_IIO is not set
+# CONFIG_PCI is not set
+# CONFIG_COREBUILD_RUN is not set
+
+# ============================================================
+# Required features for this board (override if defconfig lacks)
+# --- Restrict to Allwinner (Orangepi Zero 2W) only ---
+# CONFIG_ARCH_ACTIONS is not set
+# CONFIG_ARCH_AIROHA is not set
+# CONFIG_ARCH_ALPINE is not set
+# CONFIG_ARCH_APPLE is not set
+# CONFIG_ARCH_ARTPEC is not set
+# CONFIG_ARCH_AXIADO is not set
+# CONFIG_ARCH_BCM2835 is not set
+# CONFIG_ARCH_BCM_IPROC is not set
+# CONFIG_ARCH_BCMBCA is not set
+# CONFIG_ARCH_BRCMSTB is not set
+# CONFIG_ARCH_BERLIN is not set
+# CONFIG_ARCH_BLAIZE is not set
+# CONFIG_ARCH_BST is not set
+# CONFIG_ARCH_CIX is not set
+# CONFIG_ARCH_EXYNOS is not set
+# CONFIG_ARCH_K3 is not set
+# CONFIG_ARCH_LG1K is not set
+# CONFIG_ARCH_HISI is not set
+# CONFIG_ARCH_KEEMBAY is not set
+# CONFIG_ARCH_MEDIATEK is not set
+# CONFIG_ARCH_MESON is not set
+# CONFIG_ARCH_LAN969X is not set
+# CONFIG_ARCH_SPARX5 is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_MVEBU is not set
+# CONFIG_ARCH_LAYERSCAPE is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_S32 is not set
+# CONFIG_ARCH_MA35 is not set
+# CONFIG_ARCH_NPCM is not set
+# CONFIG_ARCH_QCOM is not set
+# CONFIG_ARCH_REALTEK is not set
+# CONFIG_ARCH_RENESAS is not set
+# CONFIG_ARCH_ROCKCHIP is not set
+# CONFIG_ARCH_SEATTLE is not set
+# CONFIG_ARCH_INTEL_SOCFPGA is not set
+# CONFIG_ARCH_SOPHGO is not set
+# CONFIG_ARCH_STM32 is not set
+# CONFIG_ARCH_SYNQUACER is not set
+# CONFIG_ARCH_TEGRA is not set
+# CONFIG_ARCH_TESLA_FSD is not set
+# CONFIG_ARCH_SPRD is not set
+# CONFIG_ARCH_THUNDER is not set
+# CONFIG_ARCH_THUNDER2 is not set
+# CONFIG_ARCH_UNIPHIER is not set
+# CONFIG_ARCH_VEXPRESS is not set
+# CONFIG_ARCH_VISCONTI is not set
+# CONFIG_ARCH_XGENE is not set
+# CONFIG_ARCH_ZYNQMP is not set
+
+# --- Disable driver modules not needed on this board ---
+# (keep only cfg80211/mac80211 as modules for the out-of-tree UWE5622 driver)
+# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+# CONFIG_ARM_ALLWINNER_SUN50I_CPUFREQ_NVMEM is not set
+# CONFIG_ACPI_CPPC_CPUFREQ is not set
+# CONFIG_NET_IP_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_IPV6_SIT is not set
+# CONFIG_NF_CONNTRACK is not set
+# CONFIG_NF_LOG_SYSLOG is not set
+# CONFIG_NETFILTER_XTABLES is not set
+# CONFIG_NETFILTER_XT_MARK is not set
+# CONFIG_NETFILTER_XT_TARGET_LOG is not set
+# CONFIG_NETFILTER_XT_MATCH_ADDRTYPE is not set
+# CONFIG_NETFILTER_XT_MATCH_CONNTRACK is not set
+# CONFIG_NETFILTER_XT_MATCH_IPVS is not set
+# CONFIG_IP_VS is not set
+# CONFIG_NF_DEFRAG_IPV4 is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_NF_LOG_IPV6 is not set
+# CONFIG_IP6_NF_IPTABLES is not set
+# CONFIG_NF_DEFRAG_IPV6 is not set
+# CONFIG_STP is not set
+# CONFIG_GARP is not set
+# CONFIG_MRP is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_LLC is not set
+# CONFIG_NET_SCH_CBS is not set
+# CONFIG_NET_SCH_ETF is not set
+# CONFIG_NET_SCH_MQPRIO_LIB is not set
+# CONFIG_NET_SCH_TAPRIO is not set
+# CONFIG_NET_SCH_MQPRIO is not set
+# CONFIG_NET_SCH_INGRESS is not set
+# CONFIG_NET_CLS_BASIC is not set
+# CONFIG_NET_CLS_FLOWER is not set
+# CONFIG_NET_ACT_GACT is not set
+# CONFIG_NET_ACT_MIRRED is not set
+# CONFIG_NET_ACT_GATE is not set
+# CONFIG_QRTR is not set
+# CONFIG_QRTR_SMD is not set
+# CONFIG_QRTR_TUN is not set
+# CONFIG_QRTR_MHI is not set
+# CONFIG_CAN is not set
+# CONFIG_CAN_RAW is not set
+# CONFIG_CAN_BCM is not set
+# CONFIG_CAN_GW is not set
+# CONFIG_NFC is not set
+# CONFIG_NFC_NCI is not set
+# CONFIG_NFC_NXP_NCI_I2C is not set
+# CONFIG_NFC_S3FWRN5 is not set
+# CONFIG_NFC_S3FWRN5_I2C is not set
+# CONFIG_REGMAP_SLIMBUS is not set
+# CONFIG_REGMAP_SPMI is not set
+# CONFIG_MHI_BUS is not set
+# CONFIG_GOOGLE_CBMEM is not set
+# CONFIG_GOOGLE_COREBOOT_TABLE is not set
+# CONFIG_GNSS is not set
+# CONFIG_GNSS_SERIAL is not set
+# CONFIG_GNSS_MTK_SERIAL is not set
+# CONFIG_MTD_NAND_BRCMNAND is not set
+# CONFIG_MTD_NAND_BRCMNAND_BCMBCA is not set
+# CONFIG_MTD_NAND_BRCMNAND_BRCMSTB is not set
+# CONFIG_MTD_NAND_BRCMNAND_IPROC is not set
+# CONFIG_MTD_UBI is not set
+# CONFIG_MTD_HYPERBUS is not set
+# CONFIG_BLK_DEV_NBD is not set
+# CONFIG_TPS6594_ESM is not set
+# CONFIG_TPS6594_PFSM is not set
+# CONFIG_EEPROM_AT24 is not set
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_UACCE is not set
+# CONFIG_RAID_ATTRS is not set
+# CONFIG_BLK_DEV_MD is not set
+# CONFIG_BLK_DEV_DM is not set
+# CONFIG_DM_MIRROR is not set
+# CONFIG_DM_ZERO is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_MACVTAP is not set
+# CONFIG_TAP is not set
+# CONFIG_VETH is not set
+# CONFIG_MHI_NET is not set
+# CONFIG_BCMGENET is not set
+# CONFIG_SYSTEMPORT is not set
+# CONFIG_QCOM_EMAC is not set
+# CONFIG_RMNET is not set
+# CONFIG_STMMAC_ETH is not set
+# CONFIG_STMMAC_PLATFORM is not set
+# CONFIG_DWMAC_GENERIC is not set
+# CONFIG_DWMAC_SUNXI is not set
+# CONFIG_DWMAC_SUN8I is not set
+# CONFIG_DWMAC_SUN55I is not set
+# CONFIG_XILINX_AXI_EMAC is not set
+# CONFIG_AX88796B_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_BCM54140_PHY is not set
+# CONFIG_BCM7XXX_PHY is not set
+# CONFIG_BCM_NET_PHYLIB is not set
+# CONFIG_MARVELL_PHY is not set
+# CONFIG_MICROCHIP_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_DP83869_PHY is not set
+# CONFIG_CAN_DEV is not set
+# CONFIG_CAN_FLEXCAN is not set
+# CONFIG_CAN_M_CAN is not set
+# CONFIG_CAN_M_CAN_PLATFORM is not set
+# CONFIG_CAN_MCP251XFD is not set
+# CONFIG_PCS_XPCS is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_RTL8152 is not set
+# CONFIG_USB_LAN78XX is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_USB_NET_AX8817X is not set
+# CONFIG_USB_NET_AX88179_178A is not set
+# CONFIG_USB_NET_CDCETHER is not set
+# CONFIG_USB_NET_CDC_NCM is not set
+# CONFIG_USB_NET_DM9601 is not set
+# CONFIG_USB_NET_SR9800 is not set
+# CONFIG_USB_NET_SMSC75XX is not set
+# CONFIG_USB_NET_SMSC95XX is not set
+# CONFIG_USB_NET_NET1080 is not set
+# CONFIG_USB_NET_PLUSB is not set
+# CONFIG_USB_NET_MCS7830 is not set
+# CONFIG_USB_NET_CDC_SUBSET_ENABLE is not set
+# CONFIG_USB_NET_CDC_SUBSET is not set
+# CONFIG_USB_NET_ZAURUS is not set
+# CONFIG_USB_RTL8153_ECM is not set
+# CONFIG_ATH_COMMON is not set
+# CONFIG_ATH10K is not set
+# CONFIG_ATH10K_SDIO is not set
+# CONFIG_WCN36XX is not set
+# CONFIG_ATH11K is not set
+# CONFIG_ATH11K_AHB is not set
+# CONFIG_BRCMUTIL is not set
+# CONFIG_BRCMFMAC is not set
+# CONFIG_MWIFIEX is not set
+# CONFIG_MWIFIEX_SDIO is not set
+# CONFIG_RTL_CARDS is not set
+# CONFIG_RSI_91X is not set
+# CONFIG_RSI_SDIO is not set
+# CONFIG_RSI_USB is not set
+# CONFIG_WL18XX is not set
+# CONFIG_WLCORE is not set
+# CONFIG_WLCORE_SDIO is not set
+# CONFIG_WWAN is not set
+# CONFIG_MHI_WWAN_CTRL is not set
+# CONFIG_MHI_WWAN_MBIM is not set
+# CONFIG_INPUT_FF_MEMLESS is not set
+# CONFIG_KEYBOARD_GPIO_POLLED is not set
+# CONFIG_KEYBOARD_MTK_PMIC is not set
+# CONFIG_MOUSE_ELAN_I2C is not set
+# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set
+# CONFIG_TOUCHSCREEN_GOODIX is not set
+# CONFIG_TOUCHSCREEN_GOODIX_BERLIN_CORE is not set
+# CONFIG_TOUCHSCREEN_GOODIX_BERLIN_SPI is not set
+# CONFIG_TOUCHSCREEN_ELAN is not set
+# CONFIG_TOUCHSCREEN_EDT_FT5X06 is not set
+# CONFIG_INPUT_AW86927 is not set
+# CONFIG_INPUT_TPS65219_PWRBUTTON is not set
+# CONFIG_INPUT_TPS6594_PWRBUTTON is not set
+# CONFIG_INPUT_PWM_BEEPER is not set
+# CONFIG_INPUT_PWM_VIBRA is not set
+# CONFIG_INPUT_RK805_PWRKEY is not set
+# CONFIG_INPUT_DA9063_ONKEY is not set
+# CONFIG_IPMI_HANDLER is not set
+# CONFIG_IPMI_DEVICE_INTERFACE is not set
+# CONFIG_IPMI_SI is not set
+# CONFIG_TCG_TIS_CORE is not set
+# CONFIG_TCG_TIS is not set
+# CONFIG_TCG_TIS_SPI is not set
+# CONFIG_TCG_TIS_I2C_CR50 is not set
+# CONFIG_I2C_ALGOBIT is not set
+# CONFIG_I2C_CADENCE is not set
+# CONFIG_I2C_GPIO is not set
+# CONFIG_SPI_DESIGNWARE is not set
+# CONFIG_SPI_DW_MMIO is not set
+# CONFIG_SPI_SPIDEV is not set
+# CONFIG_PINCTRL_DA9062 is not set
+# CONFIG_PINCTRL_RK805 is not set
+# CONFIG_PINCTRL_TPS6594 is not set
+# CONFIG_GPIO_REGMAP is not set
+# CONFIG_GPIO_ALTERA is not set
+# CONFIG_GPIO_WCD934X is not set
+# CONFIG_GPIO_ADP5585 is not set
+# CONFIG_GPIO_BD9571MWV is not set
+# CONFIG_GPIO_MAX77759 is not set
+# CONFIG_GPIO_AGGREGATOR is not set
+# CONFIG_NVMEM_REBOOT_MODE is not set
+# CONFIG_POWER_SEQUENCING_QCOM_WCN is not set
+# CONFIG_BATTERY_SBS is not set
+# CONFIG_BATTERY_MAX17042 is not set
+# CONFIG_CHARGER_MAX77759 is not set
+# CONFIG_CHARGER_MT6360 is not set
+# CONFIG_CHARGER_BQ25890 is not set
+# CONFIG_CHARGER_BQ25980 is not set
+# CONFIG_CHARGER_RK817 is not set
+# CONFIG_SENSORS_GPIO_FAN is not set
+# CONFIG_SENSORS_JC42 is not set
+# CONFIG_SENSORS_LM75 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_PWM_FAN is not set
+# CONFIG_SENSORS_INA2XX is not set
+# CONFIG_SENSORS_INA3221 is not set
+# CONFIG_SUNXI_WATCHDOG is not set
+# CONFIG_MFD_ADP5585 is not set
+# CONFIG_MFD_DA9062 is not set
+# CONFIG_MFD_MAX77759 is not set
+# CONFIG_MFD_TI_LP873X is not set
+# CONFIG_MFD_TPS6594 is not set
+# CONFIG_MFD_TPS6594_I2C is not set
+# CONFIG_MFD_WM8994 is not set
+# CONFIG_MFD_WCD934X is not set
+# CONFIG_REGULATOR_DA9211 is not set
+# CONFIG_REGULATOR_LP873X is not set
+# CONFIG_REGULATOR_MAX20411 is not set
+# CONFIG_REGULATOR_MT6315 is not set
+# CONFIG_REGULATOR_QCOM_PM8008 is not set
+# CONFIG_REGULATOR_QCOM_USB_VBUS is not set
+# CONFIG_REGULATOR_TPS65132 is not set
+# CONFIG_REGULATOR_TPS6594 is not set
+# CONFIG_REGULATOR_VCTRL is not set
+# CONFIG_RC_CORE is not set
+# CONFIG_RC_MAP is not set
+# CONFIG_IR_GPIO_CIR is not set
+# CONFIG_IR_SUNXI is not set
+# CONFIG_CEC_CORE is not set
+# CONFIG_CEC_NXP_TDA9950 is not set
+# CONFIG_HID_MULTITOUCH is not set
+# CONFIG_I2C_HID_ACPI is not set
+# CONFIG_I2C_HID_OF is not set
+# CONFIG_I2C_HID_OF_ELAN is not set
+# CONFIG_I2C_HID_CORE is not set
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_CDNS_SUPPORT is not set
+# CONFIG_USB_CDNS3 is not set
+# CONFIG_USB_SERIAL is not set
+# CONFIG_USB_SERIAL_CP210X is not set
+# CONFIG_USB_SERIAL_FTDI_SIO is not set
+# CONFIG_USB_SERIAL_WWAN is not set
+# CONFIG_USB_SERIAL_OPTION is not set
+# CONFIG_USB_ONBOARD_DEV is not set
+# CONFIG_USB_LIBCOMPOSITE is not set
+# CONFIG_USB_F_ACM is not set
+# CONFIG_USB_U_SERIAL is not set
+# CONFIG_USB_U_ETHER is not set
+# CONFIG_USB_F_SERIAL is not set
+# CONFIG_USB_F_OBEX is not set
+# CONFIG_USB_F_NCM is not set
+# CONFIG_USB_F_ECM is not set
+# CONFIG_USB_F_EEM is not set
+# CONFIG_USB_F_SUBSET is not set
+# CONFIG_USB_F_RNDIS is not set
+# CONFIG_USB_F_MASS_STORAGE is not set
+# CONFIG_USB_F_FS is not set
+# CONFIG_USB_CONFIGFS is not set
+# CONFIG_USB_MASS_STORAGE is not set
+# CONFIG_TYPEC is not set
+# CONFIG_TYPEC_TCPM is not set
+# CONFIG_TYPEC_TCPCI is not set
+# CONFIG_TYPEC_FUSB302 is not set
+# CONFIG_TYPEC_UCSI is not set
+# CONFIG_UCSI_CCG is not set
+# CONFIG_CROS_EC_UCSI is not set
+# CONFIG_TYPEC_TPS6598X is not set
+# CONFIG_TYPEC_HD3SS3220 is not set
+# CONFIG_TYPEC_MUX_FSA4480 is not set
+# CONFIG_TYPEC_MUX_GPIO_SBU is not set
+# CONFIG_TYPEC_MUX_NB7VPQ904M is not set
+# CONFIG_TYPEC_MUX_PS883X is not set
+# CONFIG_TYPEC_MUX_WCD939X_USBSS is not set
+# CONFIG_LEDS_CLASS_MULTICOLOR is not set
+# CONFIG_LEDS_CROS_EC is not set
+# CONFIG_LEDS_LM3692X is not set
+# CONFIG_LEDS_PCA9532 is not set
+# CONFIG_LEDS_QCOM_LPG is not set
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_HYM8563 is not set
+# CONFIG_RTC_DRV_RK808 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_PCF85363 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_BQ32K is not set
+# CONFIG_RTC_DRV_TPS6594 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+# CONFIG_RTC_DRV_RV3028 is not set
+# CONFIG_RTC_DRV_RV8803 is not set
+# CONFIG_RTC_DRV_PCF2127 is not set
+# CONFIG_RTC_DRV_PCF85063 is not set
+# CONFIG_RTC_DRV_DA9063 is not set
+# CONFIG_RTC_DRV_MT6397 is not set
+CONFIG_DMA_SUN6I=y
+# CONFIG_GREYBUS_BEAGLEPLAY is not set
+# CONFIG_CROS_EC_RPMSG is not set
+# CONFIG_CROS_KBD_LED_BACKLIGHT is not set
+# CONFIG_CROS_EC_CHARDEV is not set
+# CONFIG_CROS_EC_TYPEC is not set
+# CONFIG_CROS_TYPEC_SWITCH is not set
+# CONFIG_COMMON_CLK_BD718XX is not set
+# CONFIG_RPMSG_CHAR is not set
+# CONFIG_RPMSG_CTRL is not set
+# CONFIG_QCOM_QMI_HELPERS is not set
+# CONFIG_QCOM_PBS is not set
+# CONFIG_DEVFREQ_GOV_PASSIVE is not set
+# CONFIG_EXTCON_PTN5150 is not set
+# CONFIG_PWM_ADP5585 is not set
+# CONFIG_PWM_CROS_EC is not set
+# CONFIG_PWM_SUN4I is not set
+# CONFIG_RESET_GPIO is not set
+# CONFIG_PHY_CAN_TRANSCEIVER is not set
+# CONFIG_PHY_NXP_PTN3222 is not set
+# CONFIG_PHY_SUN6I_MIPI_DPHY is not set
+# CONFIG_PHY_CADENCE_TORRENT is not set
+# CONFIG_PHY_CADENCE_DPHY_RX is not set
+# CONFIG_PHY_CADENCE_SIERRA is not set
+# CONFIG_PHY_CADENCE_SALVO is not set
+# CONFIG_PHY_QCOM_USB_HS is not set
+# CONFIG_ARM_CCI_PMU is not set
+# CONFIG_ARM_CCN is not set
+# CONFIG_ARM_CMN is not set
+# CONFIG_ARM_SMMU_V3_PMU is not set
+# CONFIG_ARM_DSU_PMU is not set
+# CONFIG_ARM_SPE_PMU is not set
+# CONFIG_ARM_DMC620_PMU is not set
+# CONFIG_ARM_CORESIGHT_PMU_ARCH_SYSTEM_PMU is not set
+# CONFIG_NVIDIA_CORESIGHT_PMU_ARCH_SYSTEM_PMU is not set
+# CONFIG_NVMEM_LAYOUT_SL28_VPD is not set
+# CONFIG_NVMEM_MAX77759 is not set
+# CONFIG_NVMEM_RMEM is not set
+# CONFIG_NVMEM_SPMI_SDAM is not set
+# CONFIG_STM is not set
+# CONFIG_FPGA_BRIDGE is not set
+# CONFIG_ALTERA_FREEZE_BRIDGE is not set
+# CONFIG_FPGA_REGION is not set
+# CONFIG_OF_FPGA_REGION is not set
+# CONFIG_MUX_GPIO is not set
+# CONFIG_SLIMBUS is not set
+# CONFIG_COUNTER is not set
+# CONFIG_FUSE_FS is not set
+# CONFIG_CUSE is not set
+# CONFIG_PSTORE_RAM is not set
+# CONFIG_CRYPTO_KPP2 is not set
+# CONFIG_CRYPTO_KPP is not set
+# CONFIG_CRYPTO_AUTHENC is not set
+# CONFIG_CRYPTO_BENCHMARK is not set
+# CONFIG_CRYPTO_ENGINE is not set
+# CONFIG_CRYPTO_DH is not set
+# CONFIG_CRYPTO_ECC is not set
+# CONFIG_CRYPTO_ECDH is not set
+# CONFIG_CRYPTO_DES is not set
+# CONFIG_CRYPTO_SM4 is not set
+# CONFIG_CRYPTO_SM4_GENERIC is not set
+# CONFIG_CRYPTO_CTR is not set
+# CONFIG_CRYPTO_XTS is not set
+# CONFIG_CRYPTO_MD5 is not set
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_SHA3 is not set
+# CONFIG_CRYPTO_SM3 is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_ZSTD is not set
+# CONFIG_CRYPTO_USER_API is not set
+# CONFIG_CRYPTO_USER_API_RNG is not set
+# CONFIG_CRYPTO_AES_ARM64_NEON_BLK is not set
+# CONFIG_CRYPTO_AES_ARM64_BS is not set
+# CONFIG_CRYPTO_DEV_SUN8I_CE is not set
+# CONFIG_CRYPTO_DEV_CCREE is not set
+# CONFIG_CRYPTO_DEV_HISI_TRNG is not set
+# CONFIG_CRYPTO_DEV_AMLOGIC_GXL is not set
+# CONFIG_CRC16 is not set
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRYPTO_LIB_ARC4 is not set
+# CONFIG_CRYPTO_LIB_DES is not set
+# CONFIG_CRYPTO_LIB_GF128HASH is not set
+# CONFIG_CRYPTO_LIB_MD5 is not set
+# CONFIG_CRYPTO_LIB_SHA512 is not set
+# CONFIG_CRYPTO_LIB_SHA3 is not set
+# CONFIG_CRYPTO_LIB_SM3 is not set
+# CONFIG_LZ4_COMPRESS is not set
+# CONFIG_ZSTD_COMPRESS is not set
+# CONFIG_REED_SOLOMON is not set
+# CONFIG_CORESIGHT is not set
+# CONFIG_CORESIGHT_LINKS_AND_SINKS is not set
+# CONFIG_CORESIGHT_LINK_AND_SINK_TMC is not set
+# CONFIG_CORESIGHT_CATU is not set
+# CONFIG_CORESIGHT_SINK_TPIU is not set
+# CONFIG_CORESIGHT_SINK_ETBV10 is not set
+# CONFIG_CORESIGHT_STM is not set
+# CONFIG_CORESIGHT_CPU_DEBUG is not set
+# CONFIG_CORESIGHT_CTI is not set
+
+# --- Surplus subsystems on this board (disable to shrink kernel) ---
+# CONFIG_KVM is not set
+# CONFIG_KEXEC is not set
+# CONFIG_CRASH_DUMP is not set
+# CONFIG_HIBERNATION is not set
+# CONFIG_AUDIT is not set
+# CONFIG_SECURITY is not set
+# CONFIG_PERF_EVENTS is not set
+# CONFIG_MD is not set
+# CONFIG_BLK_DEV_LOOP is not set
+# CONFIG_DEVPORT is not set
+# CONFIG_DRM_DEBUG_SELFTEST is not set
+
+# --- Drop block/SCSI/NVME (SPI NOR + squashfs is enough) ---
+# CONFIG_BLK_DEV_NVME is not set
+
+# --- Networking: keep only what wpa_supplicant/hostapd/dnsmasq/dropbear need ---
+# CONFIG_IPV6 is not set
+# CONFIG_INET6 is not set
+# CONFIG_NETFILTER is not set
+# CONFIG_XFRM is not set
+# CONFIG_SCTP is not set
+# CONFIG_DCCP is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_NET_CLS is not set
+CONFIG_IPV4=y
+
+# --- USB: dwc3 not needed (WiFi is SDIO), keep minimal ---
+# CONFIG_USB is not set
+# CONFIG_PHY_SUN4I_USB is not set
+
+# --- Ethernet: none on Zero 2W ---
+# CONFIG_ETHERNET is not set
+
+# --- Input/HID: not needed (headless) ---
+# CONFIG_HID is not set
+
+# --- Trim crypto: only what dropbear/ssh/wireless require ---
+# CONFIG_CRYPTO_LZO is not set
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CMAC=n
+CONFIG_CRYPTO_CCM=n
+CONFIG_CRYPTO_GCM=n
+CONFIG_CRYPTO_CURVE25519=n
+
+# --- Kernel debug/bloat: strip for tiny kernel ---
+# CONFIG_KALLSYMS is not set
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_BASE_RELATIVE is not set
+# CONFIG_DEBUG_INFO is not set
+# CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT is not set
+# CONFIG_DEBUG_INFO_REDUCED is not set
+# CONFIG_DEBUG_KERNEL is not set
+# CONFIG_IKCONFIG is not set
+# CONFIG_IKCONFIG_PROC is not set
+# CONFIG_FRAME_POINTER is not set
+# CONFIG_GCC_PLUGINS is not set
+# CONFIG_ARM64_PTR_AUTH is not set
+# CONFIG_ARM64_BTI is not set
+# CONFIG_ARM64_MTE is not set
diff --git a/board/orangepi/orangepi-zero3/post-image.sh b/board/orangepi/orangepi-zero3/post-image.sh
new file mode 100755
index 0000000000..588e25bbb7
--- /dev/null
+++ b/board/orangepi/orangepi-zero3/post-image.sh
@@ -0,0 +1,34 @@
+#!/bin/sh
+#
+# OrangePi Zero 3 — build the FIT image, then assemble the SD card and the
+# SPI-NOR images.
+#
+# The kernel is LZMA-compressed so that it fits the 5376K kernel partition.
+# A FIT image is a device tree, so fit.its is compiled with dtc (as mkimage
+# would do internally, but Buildroot's host-uboot-tools is built with an empty
+# CONFIG_MKIMAGE_DTC_PATH, so mkimage cannot invoke dtc here).
+#
+# The raw 16 MiB flash layout is described in genimage-spi.cfg; both images are
+# assembled by the generic genimage wrapper (support/scripts/genimage.sh).
+
+set -e
+
+BOARD_DIR="$(dirname "$0")"
+
+# FIT: LZMA-compressed kernel + DTB.
+xz --format=lzma -9 -c "${BINARIES_DIR}/Image" > "${BINARIES_DIR}/kernel.lzma"
+
+DTB="${BINARIES_DIR}/allwinner/sun50i-h618-orangepi-zero3.dtb"
+[ -f "${DTB}" ] || { echo "ERROR: DTB not found: ${DTB}" >&2; exit 1; }
+cp "${DTB}" "${BINARIES_DIR}/dtb.bin"
+
+# The /incbin/ paths in fit.its are relative to the working directory.
+cp "${BOARD_DIR}/fit.its" "${BINARIES_DIR}/fit.its"
+(cd "${BINARIES_DIR}" && \
+ "${HOST_DIR}/bin/dtc" -I dts -O dtb -p 500 -o fit.itb fit.its)
+
+# SD card image (genimage.cfg is generated by the common OrangePi post-build).
+support/scripts/genimage.sh -c "${BINARIES_DIR}/genimage.cfg"
+
+# SPI-NOR image.
+support/scripts/genimage.sh -c "${BOARD_DIR}/genimage-spi.cfg"
diff --git a/board/orangepi/orangepi-zero3/uboot.fragment b/board/orangepi/orangepi-zero3/uboot.fragment
new file mode 100644
index 0000000000..070a0b7fbb
--- /dev/null
+++ b/board/orangepi/orangepi-zero3/uboot.fragment
@@ -0,0 +1,6 @@
+# Boot the SPI-NOR image first: read the FIT from offset 0xE0000 and bootm it.
+# If that fails, fall back to the default boot flow (distro boot: SD card, USB,
+# network). Setting CONFIG_BOOTCOMMAND only replaces the default 'bootcmd',
+# while keeping distro_bootcmd available.
+CONFIG_BOOTCOMMAND="sf probe; if sf read 0x48000000 0xE0000 0x540000; then setenv bootargs console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs mtdparts=spi0.0:896k(u-boot),5376k(kernel),10112k(rootfs); bootm 0x48000000; fi; run distro_bootcmd"
+CONFIG_BOOTDELAY=2
diff --git a/configs/orangepi_zero3_defconfig b/configs/orangepi_zero3_defconfig
index c6aa9c991a..bfaec7ebd5 100644
--- a/configs/orangepi_zero3_defconfig
+++ b/configs/orangepi_zero3_defconfig
@@ -7,8 +7,8 @@ BR2_TARGET_GENERIC_ISSUE="Welcome to Orangepi Zero3"
BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_MDEV=y
BR2_SYSTEM_DHCP="eth0"
BR2_ROOTFS_POST_BUILD_SCRIPT="board/orangepi/common/post-build.sh"
-BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh"
-BR2_ROOTFS_POST_SCRIPT_ARGS="-c $(BINARIES_DIR)/genimage.cfg"
+BR2_ROOTFS_POST_IMAGE_SCRIPT="board/orangepi/orangepi-zero3/post-image.sh"
+BR2_ROOTFS_POST_SCRIPT_ARGS=""
BR2_LINUX_KERNEL=y
BR2_LINUX_KERNEL_CUSTOM_VERSION=y
BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="6.12.6"
@@ -18,9 +18,12 @@ BR2_LINUX_KERNEL_INTREE_DTS_NAME="allwinner/sun50i-h618-orangepi-zero3"
BR2_LINUX_KERNEL_DTB_KEEP_DIRNAME=y
BR2_LINUX_KERNEL_INSTALL_TARGET=y
BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y
+BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="board/orangepi/orangepi-zero3/linux.fragment board/orangepi/orangepi-zero3/linux-net.fragment"
BR2_TARGET_ROOTFS_EXT2=y
BR2_TARGET_ROOTFS_EXT2_4=y
BR2_TARGET_ROOTFS_EXT2_SIZE="130M"
+BR2_TARGET_ROOTFS_SQUASHFS=y
+BR2_TARGET_ROOTFS_SQUASHFS4_XZ=y
# BR2_TARGET_ROOTFS_TAR is not set
BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y
@@ -39,5 +42,6 @@ BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y
BR2_TARGET_UBOOT_SPL=y
BR2_TARGET_UBOOT_SPL_NAME="u-boot-sunxi-with-spl.bin"
BR2_TARGET_UBOOT_CUSTOM_MAKEOPTS="SCP=/dev/null"
+BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/orangepi/orangepi-zero3/uboot.fragment"
BR2_PACKAGE_HOST_GENIMAGE=y
BR2_PACKAGE_HOST_UBOOT_TOOLS=y
--
2.53.0
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply related [flat|nested] 3+ messages in thread* [Buildroot] [PATCH 2/2] board/orangepi/orangepi-zero2w, orangepi-zero3: set the hostname
2026-09-25 16:52 [Buildroot] [PATCH 1/2] board/orangepi/orangepi-zero3: add SPI-NOR image support Vladimir Savelev
@ 2026-09-25 16:52 ` Vladimir Savelev
2026-10-11 13:27 ` Thomas Petazzoni via buildroot
0 siblings, 1 reply; 3+ messages in thread
From: Vladimir Savelev @ 2026-09-25 16:52 UTC (permalink / raw)
To: buildroot; +Cc: Marcin Niestroj, Vladimir Savelev, Sergey Matyukevich
Give both boards a recognizable hostname instead of the generic
"buildroot". The name is used for the login banner and sent as the DHCP
hostname (option 12), so the board is easy to identify on the network.
Signed-off-by: Vladimir Savelev <anykey196@gmail.com>
---
configs/orangepi_zero2w_defconfig | 1 +
configs/orangepi_zero3_defconfig | 1 +
2 files changed, 2 insertions(+)
diff --git a/configs/orangepi_zero2w_defconfig b/configs/orangepi_zero2w_defconfig
index 2da4372fdb..c815028405 100644
--- a/configs/orangepi_zero2w_defconfig
+++ b/configs/orangepi_zero2w_defconfig
@@ -4,6 +4,7 @@ BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_12=y
BR2_GLOBAL_PATCH_DIR="board/orangepi/orangepi-zero2w/patches"
BR2_DOWNLOAD_FORCE_CHECK_HASHES=y
BR2_TARGET_GENERIC_ISSUE="Welcome to Orangepi Zero2W"
+BR2_TARGET_GENERIC_HOSTNAME="orangepi-zero2w"
BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_MDEV=y
BR2_ROOTFS_POST_BUILD_SCRIPT="board/orangepi/common/post-build.sh"
BR2_ROOTFS_POST_IMAGE_SCRIPT="board/orangepi/orangepi-zero2w/post-image.sh"
diff --git a/configs/orangepi_zero3_defconfig b/configs/orangepi_zero3_defconfig
index bfaec7ebd5..61a4f3855b 100644
--- a/configs/orangepi_zero3_defconfig
+++ b/configs/orangepi_zero3_defconfig
@@ -4,6 +4,7 @@ BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_12=y
BR2_GLOBAL_PATCH_DIR="board/orangepi/orangepi-zero3/patches"
BR2_DOWNLOAD_FORCE_CHECK_HASHES=y
BR2_TARGET_GENERIC_ISSUE="Welcome to Orangepi Zero3"
+BR2_TARGET_GENERIC_HOSTNAME="orangepi-zero3"
BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_MDEV=y
BR2_SYSTEM_DHCP="eth0"
BR2_ROOTFS_POST_BUILD_SCRIPT="board/orangepi/common/post-build.sh"
--
2.53.0
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [Buildroot] [PATCH 2/2] board/orangepi/orangepi-zero2w, orangepi-zero3: set the hostname
2026-09-25 16:52 ` [Buildroot] [PATCH 2/2] board/orangepi/orangepi-zero2w, orangepi-zero3: set the hostname Vladimir Savelev
@ 2026-10-11 13:27 ` Thomas Petazzoni via buildroot
0 siblings, 0 replies; 3+ messages in thread
From: Thomas Petazzoni via buildroot @ 2026-10-11 13:27 UTC (permalink / raw)
To: Vladimir Savelev; +Cc: buildroot, Marcin Niestroj, Sergey Matyukevich
On Fri, Sep 25, 2026 at 09:52:26PM +0500, Vladimir Savelev wrote:
> Give both boards a recognizable hostname instead of the generic
> "buildroot". The name is used for the login banner and sent as the DHCP
> hostname (option 12), so the board is easy to identify on the network.
>
> Signed-off-by: Vladimir Savelev <anykey196@gmail.com>
Applied to master, thanks!
Best regards,
Thomas Petazzoni
--
Thomas Petazzoni, co-owner and CEO, Bootlin
Embedded Linux and Kernel engineering and training
https://bootlin.com
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2026-10-11 13:27 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-09-25 16:52 [Buildroot] [PATCH 1/2] board/orangepi/orangepi-zero3: add SPI-NOR image support Vladimir Savelev
2026-09-25 16:52 ` [Buildroot] [PATCH 2/2] board/orangepi/orangepi-zero2w, orangepi-zero3: set the hostname Vladimir Savelev
2026-10-11 13:27 ` Thomas Petazzoni via buildroot
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox