* [Buildroot] Variscite Dart
@ 2024-09-18 22:19 Neil Webster
2024-09-19 11:53 ` Arnout Vandecappelle via buildroot
0 siblings, 1 reply; 15+ messages in thread
From: Neil Webster @ 2024-09-18 22:19 UTC (permalink / raw)
To: buildroot@buildroot.org
Hello,
I am new to Buildroot and have been struggling for a couple of days with
something and wondering if I could get some pointers. Please let me know
if this is not the appropriate place to post such questions.
I want to get an embedded Linux image running on a Variscite Dart Mini
(link below)
https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/dart-mx8m-mini-nxp-i-mx8m-mini/
I have the SOM connected to a dev kit referenced in the same link above.
I wanted to use the opportunity to get familiar with Buildroot but sadly
Variscite do not support Buildroot and instead they steered me towards
Yocto.
I have been able to get an image running with Yocto following their
recipes but I found the whole process to be obscure and opaque and I am
therefore back to my original objective of using Buildroot.
I have been able to follow the tutorials and get a build working on a
Raspberry Pi.
However, as mentioned above there is no support available from Variscite
and there is no specific defconfig for my hardware, so I tried to start
with freescale_imx8mmevk_defconfig as this seems to be close with what
appear to be correct settings under the "target options" menu.
However I am not getting anything at the console.
I noticed that the freescale_imx8mmevk_defconfig sets the getty TTY port
to ttymxc1, so I tried changing this to ttymxc0 as that is the port
mapped to the debug interface on the development board. Still nothing at
the console.
I tried changing the init system from busybox to systemd. Still nothing.
I feel like I am poking around in the dark. Any thoughts on what I
should try next?
Regards, Neil
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-18 22:19 [Buildroot] Variscite Dart Neil Webster
@ 2024-09-19 11:53 ` Arnout Vandecappelle via buildroot
2024-09-23 19:30 ` Neil Webster
0 siblings, 1 reply; 15+ messages in thread
From: Arnout Vandecappelle via buildroot @ 2024-09-19 11:53 UTC (permalink / raw)
To: Neil Webster, buildroot@buildroot.org
Hi Neil,
On 19/09/2024 00:19, Neil Webster wrote:
> Hello,
>
> I am new to Buildroot and have been struggling for a couple of days with
> something and wondering if I could get some pointers. Please let me know
> if this is not the appropriate place to post such questions.
>
> I want to get an embedded Linux image running on a Variscite Dart Mini
> (link below)
>
> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/dart-mx8m-mini-nxp-i-mx8m-mini/
>
> I have the SOM connected to a dev kit referenced in the same link above.
>
> I wanted to use the opportunity to get familiar with Buildroot but sadly
> Variscite do not support Buildroot and instead they steered me towards
> Yocto.
:sad-face:
> I have been able to get an image running with Yocto following their
> recipes but I found the whole process to be obscure and opaque and I am
> therefore back to my original objective of using Buildroot.
Please make sure to give this feedback to Variscite!
>
> I have been able to follow the tutorials and get a build working on a
> Raspberry Pi.
>
> However, as mentioned above there is no support available from Variscite
> and there is no specific defconfig for my hardware, so I tried to start
> with freescale_imx8mmevk_defconfig as this seems to be close with what
> appear to be correct settings under the "target options" menu.
Yes, that's an excellent start!
... but not enough to get a working board...
> However I am not getting anything at the console.
>
> I noticed that the freescale_imx8mmevk_defconfig sets the getty TTY port
> to ttymxc1, so I tried changing this to ttymxc0 as that is the port
> mapped to the debug interface on the development board. Still nothing at
> the console.
That is one of the things you need to change indeed. However, things already
went wrong way before that, because you should have gotten U-Boot and kernel
debug output on the console.
There are a number of things you have to change in a defconfig when you switch
to a different (but similar) board. I'm going to list them below with the symbol
names, not how they appear in the menu. You can always search for those symbols
in `make menuconfig` by typing /
BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
You should check Variscite's yocto layer to see if they use the NXP TF-A or if
they fork it even more. They may also use a different version.
BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
I expect that this will be OK for the Variscite board as well, but it is
possible that they have defined their own platform.
BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
You should check Variscite's yocto layer to see if they use the NXP U-Boot or if
they fork it even more. They may also use a different version.
BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
This needs to change to the U-Boot defconfig. That defconfig could be in NXP's
U-Boot fork already, or it could be in Variscite's fork, or Variscite may supply
it in their u-boot yocto recipe.
BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
freescale/imx8mm-evk-revb-qca-wifi"
You probably start to know the drill, right? The defconfig is probably OK,
although it's possible that Variscite appends a fragment to it in their
bbappend. The DTS name is most definitely not OK, but it might come from
Variscite's metalayer instead of NXP's kernel. The kernel is unlikely to be
forked by Variscite so that one is probably OK, but it may be a different version.
> I tried changing the init system from busybox to systemd. Still nothing.
No, busybox init should work fine.
> I feel like I am poking around in the dark. Any thoughts on what I
> should try next?
If you do manage to advance with this, there are two contributions you could make:
- You can add a defconfig for the Variscite board.
- You could update the documentation with a "how to add support for a new board"
section that explains what I wrote above in a better (more generic) way.
Regards,
Arnout
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-19 11:53 ` Arnout Vandecappelle via buildroot
@ 2024-09-23 19:30 ` Neil Webster
2024-09-23 19:36 ` Arnout Vandecappelle via buildroot
0 siblings, 1 reply; 15+ messages in thread
From: Neil Webster @ 2024-09-23 19:30 UTC (permalink / raw)
To: Arnout Vandecappelle, buildroot@buildroot.org
Hi Arnout,
Thank you for the response.
I will work through each of your suggestions and I started with the one
that you stated was definitely incorrect i.e. The DTS name.
The Variscite device trees are described here
https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
I found and copied three DTS(I) files
imx8mm-var-dart-dt8mcustomboard.dts
which #includes ...
imx8mm-var-dart.dtsi
which #includes ...
imx8mm.dtsi
I referenced the location of these files in
BR2_LINUX_KERNEL_CUSTOM_DTS_PATH and I see it copies them to
output/build/linux-custom/arch/arm64/boot/dts/
The subsequent build complained about missing dependencies and I also
had to add imx8mm-pinfunc.h and mxl-8611x.h to
BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is that the correct way to add .h
dependencies or is there a cleaner way or doing this i.e. should the
BR2_LINUX_KERNEL_CUSTOM_DTS_PATH be reserved for DTS files only as the
name suggests?
Anyway the build succeeded after adding those .h files but sadly still
no console. I will now move onto looking at the other items you mentioned.
Cheers, Neil
On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
> [You don't often get email from arnout@mind.be. Learn why this is
> important at https://aka.ms/LearnAboutSenderIdentification ]
>
> Hi Neil,
>
> On 19/09/2024 00:19, Neil Webster wrote:
>> Hello,
>>
>> I am new to Buildroot and have been struggling for a couple of days with
>> something and wondering if I could get some pointers. Please let me know
>> if this is not the appropriate place to post such questions.
>>
>> I want to get an embedded Linux image running on a Variscite Dart Mini
>> (link below)
>>
>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/dart-mx8m-mini-nxp-i-mx8m-mini/
>>
>>
>> I have the SOM connected to a dev kit referenced in the same link above.
>>
>> I wanted to use the opportunity to get familiar with Buildroot but sadly
>> Variscite do not support Buildroot and instead they steered me towards
>> Yocto.
>
> :sad-face:
>
>
>> I have been able to get an image running with Yocto following their
>> recipes but I found the whole process to be obscure and opaque and I am
>> therefore back to my original objective of using Buildroot.
>
> Please make sure to give this feedback to Variscite!
>
>
>>
>> I have been able to follow the tutorials and get a build working on a
>> Raspberry Pi.
>>
>> However, as mentioned above there is no support available from Variscite
>> and there is no specific defconfig for my hardware, so I tried to start
>> with freescale_imx8mmevk_defconfig as this seems to be close with what
>> appear to be correct settings under the "target options" menu.
>
> Yes, that's an excellent start!
>
> ... but not enough to get a working board...
>
>
>> However I am not getting anything at the console.
>>
>> I noticed that the freescale_imx8mmevk_defconfig sets the getty TTY port
>> to ttymxc1, so I tried changing this to ttymxc0 as that is the port
>> mapped to the debug interface on the development board. Still nothing at
>> the console.
>
> That is one of the things you need to change indeed. However, things
> already
> went wrong way before that, because you should have gotten U-Boot and
> kernel
> debug output on the console.
>
> There are a number of things you have to change in a defconfig when
> you switch
> to a different (but similar) board. I'm going to list them below with
> the symbol
> names, not how they appear in the menu. You can always search for
> those symbols
> in `make menuconfig` by typing /
>
> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>
> You should check Variscite's yocto layer to see if they use the NXP
> TF-A or if
> they fork it even more. They may also use a different version.
>
>
> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>
> I expect that this will be OK for the Variscite board as well, but it is
> possible that they have defined their own platform.
>
>
>
> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>
>
> You should check Variscite's yocto layer to see if they use the NXP
> U-Boot or if
> they fork it even more. They may also use a different version.
>
>
> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>
> This needs to change to the U-Boot defconfig. That defconfig could be
> in NXP's
> U-Boot fork already, or it could be in Variscite's fork, or Variscite
> may supply
> it in their u-boot yocto recipe.
>
>
> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>
> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
> freescale/imx8mm-evk-revb-qca-wifi"
>
> You probably start to know the drill, right? The defconfig is probably
> OK,
> although it's possible that Variscite appends a fragment to it in their
> bbappend. The DTS name is most definitely not OK, but it might come from
> Variscite's metalayer instead of NXP's kernel. The kernel is unlikely
> to be
> forked by Variscite so that one is probably OK, but it may be a
> different version.
>
>
>> I tried changing the init system from busybox to systemd. Still nothing.
>
> No, busybox init should work fine.
>
>
>> I feel like I am poking around in the dark. Any thoughts on what I
>> should try next?
>
> If you do manage to advance with this, there are two contributions
> you could make:
> - You can add a defconfig for the Variscite board.
> - You could update the documentation with a "how to add support for a
> new board"
> section that explains what I wrote above in a better (more generic) way.
>
>
> Regards,
> Arnout
>
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-23 19:30 ` Neil Webster
@ 2024-09-23 19:36 ` Arnout Vandecappelle via buildroot
2024-09-23 20:53 ` Neil Webster
0 siblings, 1 reply; 15+ messages in thread
From: Arnout Vandecappelle via buildroot @ 2024-09-23 19:36 UTC (permalink / raw)
To: Neil Webster, buildroot@buildroot.org
On 23/09/2024 21:30, Neil Webster wrote:
> Hi Arnout,
>
> Thank you for the response.
>
> I will work through each of your suggestions and I started with the one that you
> stated was definitely incorrect i.e. The DTS name.
>
> The Variscite device trees are described here
>
> https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
>
> I found and copied three DTS(I) files
>
> imx8mm-var-dart-dt8mcustomboard.dts
>
> which #includes ...
>
> imx8mm-var-dart.dtsi
>
> which #includes ...
>
> imx8mm.dtsi
This one, at least, should be in the kernel source itself. If you're using a
kernel that doesn't already have imx8mm.dtsi, it's probably going to be wildly
incompatible with Variscite's device tree.
> I referenced the location of these files in BR2_LINUX_KERNEL_CUSTOM_DTS_PATH and
> I see it copies them to output/build/linux-custom/arch/arm64/boot/dts/
>
> The subsequent build complained about missing dependencies and I also had to add
> imx8mm-pinfunc.h and mxl-8611x.h to BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is that
Again, these should normally be part of the kernel already.
> the correct way to add .h dependencies or is there a cleaner way or doing this
> i.e. should the BR2_LINUX_KERNEL_CUSTOM_DTS_PATH be reserved for DTS files only
> as the name suggests?
Not really - the header files are shared between device tree and corresponding
drivers. So they should already be part of the kernel source. If they are not,
it's quite likely that things are not going to work.
There may be situations where it makes sense to add header files to
CUSTOM_DTS_PATH, but that's squarely You Must Know What You're Doing territory...
>
> Anyway the build succeeded after adding those .h files but sadly still no
> console. I will now move onto looking at the other items you mentioned.
Well, I'd start with concentrating on getting output from TF-A and U-Boot.
Right now you don't even know if the kernel is loaded!
Regards,
Arnout
>
> Cheers, Neil
>
> On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
>> [You don't often get email from arnout@mind.be. Learn why this is important at
>> https://aka.ms/LearnAboutSenderIdentification ]
>>
>> Hi Neil,
>>
>> On 19/09/2024 00:19, Neil Webster wrote:
>>> Hello,
>>>
>>> I am new to Buildroot and have been struggling for a couple of days with
>>> something and wondering if I could get some pointers. Please let me know
>>> if this is not the appropriate place to post such questions.
>>>
>>> I want to get an embedded Linux image running on a Variscite Dart Mini
>>> (link below)
>>>
>>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/dart-
>>> mx8m-mini-nxp-i-mx8m-mini/
>>>
>>> I have the SOM connected to a dev kit referenced in the same link above.
>>>
>>> I wanted to use the opportunity to get familiar with Buildroot but sadly
>>> Variscite do not support Buildroot and instead they steered me towards
>>> Yocto.
>>
>> :sad-face:
>>
>>
>>> I have been able to get an image running with Yocto following their
>>> recipes but I found the whole process to be obscure and opaque and I am
>>> therefore back to my original objective of using Buildroot.
>>
>> Please make sure to give this feedback to Variscite!
>>
>>
>>>
>>> I have been able to follow the tutorials and get a build working on a
>>> Raspberry Pi.
>>>
>>> However, as mentioned above there is no support available from Variscite
>>> and there is no specific defconfig for my hardware, so I tried to start
>>> with freescale_imx8mmevk_defconfig as this seems to be close with what
>>> appear to be correct settings under the "target options" menu.
>>
>> Yes, that's an excellent start!
>>
>> ... but not enough to get a working board...
>>
>>
>>> However I am not getting anything at the console.
>>>
>>> I noticed that the freescale_imx8mmevk_defconfig sets the getty TTY port
>>> to ttymxc1, so I tried changing this to ttymxc0 as that is the port
>>> mapped to the debug interface on the development board. Still nothing at
>>> the console.
>>
>> That is one of the things you need to change indeed. However, things already
>> went wrong way before that, because you should have gotten U-Boot and kernel
>> debug output on the console.
>>
>> There are a number of things you have to change in a defconfig when you switch
>> to a different (but similar) board. I'm going to list them below with the symbol
>> names, not how they appear in the menu. You can always search for those symbols
>> in `make menuconfig` by typing /
>>
>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
>> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>>
>> You should check Variscite's yocto layer to see if they use the NXP TF-A or if
>> they fork it even more. They may also use a different version.
>>
>>
>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>>
>> I expect that this will be OK for the Variscite board as well, but it is
>> possible that they have defined their own platform.
>>
>>
>>
>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
>> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>>
>> You should check Variscite's yocto layer to see if they use the NXP U-Boot or if
>> they fork it even more. They may also use a different version.
>>
>>
>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>>
>> This needs to change to the U-Boot defconfig. That defconfig could be in NXP's
>> U-Boot fork already, or it could be in Variscite's fork, or Variscite may supply
>> it in their u-boot yocto recipe.
>>
>>
>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
>> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
>> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
>> freescale/imx8mm-evk-revb-qca-wifi"
>>
>> You probably start to know the drill, right? The defconfig is probably OK,
>> although it's possible that Variscite appends a fragment to it in their
>> bbappend. The DTS name is most definitely not OK, but it might come from
>> Variscite's metalayer instead of NXP's kernel. The kernel is unlikely to be
>> forked by Variscite so that one is probably OK, but it may be a different
>> version.
>>
>>
>>> I tried changing the init system from busybox to systemd. Still nothing.
>>
>> No, busybox init should work fine.
>>
>>
>>> I feel like I am poking around in the dark. Any thoughts on what I
>>> should try next?
>>
>> If you do manage to advance with this, there are two contributions you could
>> make:
>> - You can add a defconfig for the Variscite board.
>> - You could update the documentation with a "how to add support for a new board"
>> section that explains what I wrote above in a better (more generic) way.
>>
>>
>> Regards,
>> Arnout
>>
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-23 19:36 ` Arnout Vandecappelle via buildroot
@ 2024-09-23 20:53 ` Neil Webster
2024-09-24 2:58 ` Neil Webster
2024-09-24 6:23 ` Arnout Vandecappelle via buildroot
0 siblings, 2 replies; 15+ messages in thread
From: Neil Webster @ 2024-09-23 20:53 UTC (permalink / raw)
To: Arnout Vandecappelle, buildroot@buildroot.org
[-- Attachment #1: Type: text/plain, Size: 7945 bytes --]
Hi Arnout,
Thanks for the quick response.
I looked through the yocto build directory and it seems that they are
using 6.1.1-1.0.0 for all of the below.
BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION
BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION
BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION
So I changed them (.config attached).
The build failed with the following ...
ERROR: No hash found for linux-imx-lf-6.1.1-1.0.0.tar.gz
make[1]: *** [package/pkg-generic.mk:179:
/home/neil/buildroot-2024.08/output/build/linux-headers-custom/.stamp_downloaded]
Error 1
Thoughts on next steps appreciated.
Thanks for your patience in working through this with a newbie.
Cheers, Neil
On 2024-09-23 3:36 p.m., Arnout Vandecappelle wrote:
>
>
> On 23/09/2024 21:30, Neil Webster wrote:
>> Hi Arnout,
>>
>> Thank you for the response.
>>
>> I will work through each of your suggestions and I started with the
>> one that you stated was definitely incorrect i.e. The DTS name.
>>
>> The Variscite device trees are described here
>>
>> https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
>>
>>
>> I found and copied three DTS(I) files
>>
>> imx8mm-var-dart-dt8mcustomboard.dts
>>
>> which #includes ...
>>
>> imx8mm-var-dart.dtsi
>>
>> which #includes ...
>>
>> imx8mm.dtsi
>
> This one, at least, should be in the kernel source itself. If you're
> using a kernel that doesn't already have imx8mm.dtsi, it's probably
> going to be wildly incompatible with Variscite's device tree.
>
>
>> I referenced the location of these files in
>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH and I see it copies them to
>> output/build/linux-custom/arch/arm64/boot/dts/
>>
>> The subsequent build complained about missing dependencies and I also
>> had to add imx8mm-pinfunc.h and mxl-8611x.h to
>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is that
>
> Again, these should normally be part of the kernel already.
>
>> the correct way to add .h dependencies or is there a cleaner way or
>> doing this i.e. should the BR2_LINUX_KERNEL_CUSTOM_DTS_PATH be
>> reserved for DTS files only as the name suggests?
>
> Not really - the header files are shared between device tree and
> corresponding drivers. So they should already be part of the kernel
> source. If they are not, it's quite likely that things are not going
> to work.
>
> There may be situations where it makes sense to add header files to
> CUSTOM_DTS_PATH, but that's squarely You Must Know What You're Doing
> territory...
>
>
>>
>> Anyway the build succeeded after adding those .h files but sadly
>> still no console. I will now move onto looking at the other items you
>> mentioned.
>
> Well, I'd start with concentrating on getting output from TF-A and
> U-Boot. Right now you don't even know if the kernel is loaded!
>
>
> Regards,
> Arnout
>
>
>>
>> Cheers, Neil
>>
>> On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
>>> [You don't often get email from arnout@mind.be. Learn why this is
>>> important at https://aka.ms/LearnAboutSenderIdentification ]
>>>
>>> Hi Neil,
>>>
>>> On 19/09/2024 00:19, Neil Webster wrote:
>>>> Hello,
>>>>
>>>> I am new to Buildroot and have been struggling for a couple of days
>>>> with
>>>> something and wondering if I could get some pointers. Please let me
>>>> know
>>>> if this is not the appropriate place to post such questions.
>>>>
>>>> I want to get an embedded Linux image running on a Variscite Dart Mini
>>>> (link below)
>>>>
>>>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/dart-
>>>> mx8m-mini-nxp-i-mx8m-mini/
>>>>
>>>> I have the SOM connected to a dev kit referenced in the same link
>>>> above.
>>>>
>>>> I wanted to use the opportunity to get familiar with Buildroot but
>>>> sadly
>>>> Variscite do not support Buildroot and instead they steered me towards
>>>> Yocto.
>>>
>>> :sad-face:
>>>
>>>
>>>> I have been able to get an image running with Yocto following their
>>>> recipes but I found the whole process to be obscure and opaque and
>>>> I am
>>>> therefore back to my original objective of using Buildroot.
>>>
>>> Please make sure to give this feedback to Variscite!
>>>
>>>
>>>>
>>>> I have been able to follow the tutorials and get a build working on a
>>>> Raspberry Pi.
>>>>
>>>> However, as mentioned above there is no support available from
>>>> Variscite
>>>> and there is no specific defconfig for my hardware, so I tried to
>>>> start
>>>> with freescale_imx8mmevk_defconfig as this seems to be close with what
>>>> appear to be correct settings under the "target options" menu.
>>>
>>> Yes, that's an excellent start!
>>>
>>> ... but not enough to get a working board...
>>>
>>>
>>>> However I am not getting anything at the console.
>>>>
>>>> I noticed that the freescale_imx8mmevk_defconfig sets the getty TTY
>>>> port
>>>> to ttymxc1, so I tried changing this to ttymxc0 as that is the port
>>>> mapped to the debug interface on the development board. Still
>>>> nothing at
>>>> the console.
>>>
>>> That is one of the things you need to change indeed. However,
>>> things already
>>> went wrong way before that, because you should have gotten U-Boot
>>> and kernel
>>> debug output on the console.
>>>
>>> There are a number of things you have to change in a defconfig when
>>> you switch
>>> to a different (but similar) board. I'm going to list them below
>>> with the symbol
>>> names, not how they appear in the menu. You can always search for
>>> those symbols
>>> in `make menuconfig` by typing /
>>>
>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
>>> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>>>
>>> You should check Variscite's yocto layer to see if they use the NXP
>>> TF-A or if
>>> they fork it even more. They may also use a different version.
>>>
>>>
>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>>>
>>> I expect that this will be OK for the Variscite board as well, but
>>> it is
>>> possible that they have defined their own platform.
>>>
>>>
>>>
>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
>>> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>>>
>>>
>>> You should check Variscite's yocto layer to see if they use the NXP
>>> U-Boot or if
>>> they fork it even more. They may also use a different version.
>>>
>>>
>>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>>>
>>> This needs to change to the U-Boot defconfig. That defconfig could
>>> be in NXP's
>>> U-Boot fork already, or it could be in Variscite's fork, or
>>> Variscite may supply
>>> it in their u-boot yocto recipe.
>>>
>>>
>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
>>> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>>>
>>> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
>>> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
>>> freescale/imx8mm-evk-revb-qca-wifi"
>>>
>>> You probably start to know the drill, right? The defconfig is
>>> probably OK,
>>> although it's possible that Variscite appends a fragment to it in their
>>> bbappend. The DTS name is most definitely not OK, but it might come
>>> from
>>> Variscite's metalayer instead of NXP's kernel. The kernel is
>>> unlikely to be
>>> forked by Variscite so that one is probably OK, but it may be a
>>> different version.
>>>
>>>
>>>> I tried changing the init system from busybox to systemd. Still
>>>> nothing.
>>>
>>> No, busybox init should work fine.
>>>
>>>
>>>> I feel like I am poking around in the dark. Any thoughts on what I
>>>> should try next?
>>>
>>> If you do manage to advance with this, there are two contributions
>>> you could make:
>>> - You can add a defconfig for the Variscite board.
>>> - You could update the documentation with a "how to add support for
>>> a new board"
>>> section that explains what I wrote above in a better (more generic)
>>> way.
>>>
>>>
>>> Regards,
>>> Arnout
>>>
>
[-- Attachment #2: .config --]
[-- Type: text/plain, Size: 138713 bytes --]
#
# Automatically generated file; DO NOT EDIT.
# Buildroot 2024.08 Configuration
#
BR2_HAVE_DOT_CONFIG=y
BR2_HOST_GCC_AT_LEAST_4_9=y
BR2_HOST_GCC_AT_LEAST_5=y
BR2_HOST_GCC_AT_LEAST_6=y
BR2_HOST_GCC_AT_LEAST_7=y
BR2_HOST_GCC_AT_LEAST_8=y
BR2_HOST_GCC_AT_LEAST_9=y
BR2_HOST_GCC_AT_LEAST_10=y
BR2_HOST_GCC_AT_LEAST_11=y
#
# Target options
#
BR2_ARCH_IS_64=y
BR2_USE_MMU=y
# BR2_arcle is not set
# BR2_arceb is not set
# BR2_arm is not set
# BR2_armeb is not set
BR2_aarch64=y
# BR2_aarch64_be is not set
# BR2_i386 is not set
# BR2_m68k is not set
# BR2_microblazeel is not set
# BR2_microblazebe is not set
# BR2_mips is not set
# BR2_mipsel is not set
# BR2_mips64 is not set
# BR2_mips64el is not set
# BR2_nios2 is not set
# BR2_or1k is not set
# BR2_powerpc is not set
# BR2_powerpc64 is not set
# BR2_powerpc64le is not set
# BR2_riscv is not set
# BR2_s390x is not set
# BR2_sh is not set
# BR2_sparc is not set
# BR2_sparc64 is not set
# BR2_x86_64 is not set
# BR2_xtensa is not set
BR2_ARCH_HAS_TOOLCHAIN_BUILDROOT=y
BR2_ARCH="aarch64"
BR2_NORMALIZED_ARCH="arm64"
BR2_ENDIAN="LITTLE"
BR2_GCC_TARGET_ABI="lp64"
BR2_GCC_TARGET_CPU="cortex-a53"
BR2_BINFMT_SUPPORTS_SHARED=y
BR2_READELF_ARCH_NAME="AArch64"
BR2_ARM_CPU_HAS_FPU=y
BR2_ARM_CPU_HAS_VFPV2=y
BR2_ARM_CPU_HAS_VFPV3=y
BR2_ARM_CPU_HAS_VFPV4=y
BR2_ARM_CPU_HAS_FP_ARMV8=y
BR2_ARM_CPU_ARMV8A=y
#
# armv8 cores
#
# BR2_cortex_a35 is not set
BR2_cortex_a53=y
# BR2_cortex_a57 is not set
# BR2_cortex_a57_a53 is not set
# BR2_cortex_a72 is not set
# BR2_cortex_a72_a53 is not set
# BR2_cortex_a73 is not set
# BR2_cortex_a73_a35 is not set
# BR2_cortex_a73_a53 is not set
# BR2_emag is not set
# BR2_exynos_m1 is not set
# BR2_falkor is not set
# BR2_phecda is not set
# BR2_qdf24xx is not set
# BR2_thunderx is not set
# BR2_thunderxt81 is not set
# BR2_thunderxt83 is not set
# BR2_thunderxt88 is not set
# BR2_thunderxt88p1 is not set
# BR2_xgene1 is not set
#
# armv8.1a cores
#
# BR2_thunderx2t99 is not set
# BR2_thunderx2t99p1 is not set
# BR2_vulcan is not set
#
# armv8.2a cores
#
# BR2_cortex_a55 is not set
# BR2_cortex_a75 is not set
# BR2_cortex_a75_a55 is not set
# BR2_cortex_a76 is not set
# BR2_cortex_a76_a55 is not set
# BR2_neoverse_n1 is not set
# BR2_tsv110 is not set
#
# armv8.4a cores
#
# BR2_saphira is not set
# BR2_ARM_FPU_VFPV2 is not set
BR2_ARM_FPU_VFPV3=y
# BR2_ARM_FPU_VFPV3D16 is not set
# BR2_ARM_FPU_VFPV4 is not set
# BR2_ARM_FPU_VFPV4D16 is not set
# BR2_ARM_FPU_FP_ARMV8 is not set
BR2_ARM64_PAGE_SIZE_4K=y
# BR2_ARM64_PAGE_SIZE_16K is not set
# BR2_ARM64_PAGE_SIZE_64K is not set
BR2_ARM64_PAGE_SIZE="4K"
BR2_BINFMT_ELF=y
#
# Toolchain
#
BR2_TOOLCHAIN=y
BR2_TOOLCHAIN_USES_GLIBC=y
BR2_TOOLCHAIN_BUILDROOT=y
# BR2_TOOLCHAIN_EXTERNAL is not set
#
# Toolchain Buildroot Options
#
BR2_TOOLCHAIN_BUILDROOT_VENDOR="buildroot"
# BR2_TOOLCHAIN_BUILDROOT_UCLIBC is not set
BR2_TOOLCHAIN_BUILDROOT_GLIBC=y
# BR2_TOOLCHAIN_BUILDROOT_MUSL is not set
BR2_TOOLCHAIN_BUILDROOT_LIBC="glibc"
#
# Kernel Header Options
#
BR2_KERNEL_HEADERS_AS_KERNEL=y
# BR2_KERNEL_HEADERS_4_19 is not set
# BR2_KERNEL_HEADERS_5_4 is not set
# BR2_KERNEL_HEADERS_5_10 is not set
# BR2_KERNEL_HEADERS_5_15 is not set
# BR2_KERNEL_HEADERS_6_1 is not set
# BR2_KERNEL_HEADERS_6_6 is not set
# BR2_KERNEL_HEADERS_6_10 is not set
# BR2_KERNEL_HEADERS_VERSION is not set
# BR2_KERNEL_HEADERS_CUSTOM_TARBALL is not set
# BR2_KERNEL_HEADERS_CUSTOM_GIT is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_10 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_9 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_8 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_7 is not set
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_6=y
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_5 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_4 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_3 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_2 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_1 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_0 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_19 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_18 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_17 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_16 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_15 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_14 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_13 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_12 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_11 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_10 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_9 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_8 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_7 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_6 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_5 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_4 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_3 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_2 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_1 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_5_0 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_20 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_19 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_18 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_17 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_16 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_15 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_14 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_13 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_12 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_11 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_10 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_9 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_8 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_7 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_6 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_5 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_3 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_2 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_19 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_18 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_17 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_16 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_15 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_14 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_13 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_12 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_11 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_10 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_9 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_8 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_7 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_6 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_5 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_4 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_3 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_2 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_1 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_0 is not set
# BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_REALLY_OLD is not set
BR2_PACKAGE_LINUX_HEADERS=y
BR2_PACKAGE_MUSL_ARCH_SUPPORTS=y
BR2_PACKAGE_MUSL_SUPPORTS=y
BR2_PACKAGE_UCLIBC_ARCH_SUPPORTS=y
BR2_PACKAGE_UCLIBC_SUPPORTS=y
BR2_PACKAGE_GLIBC_ARCH_SUPPORTS=y
BR2_PACKAGE_GLIBC_SUPPORTS=y
#
# Glibc Options
#
BR2_PACKAGE_GLIBC=y
# BR2_PACKAGE_GLIBC_KERNEL_COMPAT is not set
# BR2_PACKAGE_GLIBC_UTILS is not set
#
# Binutils Options
#
BR2_PACKAGE_HOST_BINUTILS_SUPPORTS_CFI=y
# BR2_BINUTILS_VERSION_2_40_X is not set
BR2_BINUTILS_VERSION_2_41_X=y
# BR2_BINUTILS_VERSION_2_42_X is not set
BR2_BINUTILS_VERSION="2.41"
# BR2_BINUTILS_GPROFNG is not set
BR2_BINUTILS_EXTRA_CONFIG_OPTIONS=""
#
# GCC Options
#
# BR2_GCC_VERSION_12_X is not set
BR2_GCC_VERSION_13_X=y
# BR2_GCC_VERSION_14_X is not set
BR2_GCC_VERSION="13.3.0"
BR2_EXTRA_GCC_CONFIG_OPTIONS=""
# BR2_TOOLCHAIN_BUILDROOT_CXX is not set
# BR2_TOOLCHAIN_BUILDROOT_FORTRAN is not set
# BR2_GCC_ENABLE_OPENMP is not set
# BR2_GCC_ENABLE_GRAPHITE is not set
BR2_PACKAGE_GCC_FINAL=y
BR2_PACKAGE_HOST_GDB_ARCH_SUPPORTS=y
#
# Host GDB Options
#
# BR2_PACKAGE_HOST_GDB is not set
#
# Toolchain Generic Options
#
BR2_TOOLCHAIN_SUPPORTS_ALWAYS_LOCKFREE_ATOMIC_INTS=y
BR2_TOOLCHAIN_SUPPORTS_VARIADIC_MI_THUNK=y
BR2_USE_WCHAR=y
BR2_ENABLE_LOCALE=y
BR2_TOOLCHAIN_HAS_THREADS=y
BR2_TOOLCHAIN_HAS_THREADS_DEBUG=y
BR2_TOOLCHAIN_HAS_THREADS_NPTL=y
BR2_TOOLCHAIN_HAS_SSP=y
BR2_TOOLCHAIN_HAS_SSP_STRONG=y
BR2_TOOLCHAIN_HAS_UCONTEXT=y
BR2_TOOLCHAIN_SUPPORTS_PIE=y
# BR2_TOOLCHAIN_GLIBC_GCONV_LIBS_COPY is not set
BR2_TOOLCHAIN_EXTRA_LIBS=""
BR2_TOOLCHAIN_HAS_FULL_GETTEXT=y
BR2_TARGET_OPTIMIZATION=""
BR2_TARGET_LDFLAGS=""
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_0=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_1=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_2=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_3=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_4=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_5=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_6=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_7=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_8=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_9=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_10=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_11=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_12=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_13=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_14=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_15=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_16=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_17=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_18=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_3_19=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_0=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_1=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_2=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_3=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_4=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_5=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_6=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_7=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_8=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_9=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_10=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_11=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_12=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_13=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_14=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_15=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_16=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_17=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_18=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_19=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_4_20=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_0=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_1=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_2=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_3=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_4=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_5=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_6=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_7=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_8=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_9=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_10=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_11=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_12=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_13=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_14=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_15=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_16=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_17=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_18=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_5_19=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_6_0=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_6_1=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_6_2=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_6_3=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_6_4=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_6_5=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST_6_6=y
BR2_TOOLCHAIN_HEADERS_AT_LEAST="6.6"
BR2_TOOLCHAIN_GCC_AT_LEAST_4_3=y
BR2_TOOLCHAIN_GCC_AT_LEAST_4_4=y
BR2_TOOLCHAIN_GCC_AT_LEAST_4_5=y
BR2_TOOLCHAIN_GCC_AT_LEAST_4_6=y
BR2_TOOLCHAIN_GCC_AT_LEAST_4_7=y
BR2_TOOLCHAIN_GCC_AT_LEAST_4_8=y
BR2_TOOLCHAIN_GCC_AT_LEAST_4_9=y
BR2_TOOLCHAIN_GCC_AT_LEAST_5=y
BR2_TOOLCHAIN_GCC_AT_LEAST_6=y
BR2_TOOLCHAIN_GCC_AT_LEAST_7=y
BR2_TOOLCHAIN_GCC_AT_LEAST_8=y
BR2_TOOLCHAIN_GCC_AT_LEAST_9=y
BR2_TOOLCHAIN_GCC_AT_LEAST_10=y
BR2_TOOLCHAIN_GCC_AT_LEAST_11=y
BR2_TOOLCHAIN_GCC_AT_LEAST_12=y
BR2_TOOLCHAIN_GCC_AT_LEAST_13=y
BR2_TOOLCHAIN_GCC_AT_LEAST="13"
BR2_TOOLCHAIN_HAS_MNAN_OPTION=y
BR2_TOOLCHAIN_HAS_SYNC_1=y
BR2_TOOLCHAIN_HAS_SYNC_2=y
BR2_TOOLCHAIN_HAS_SYNC_4=y
BR2_TOOLCHAIN_HAS_SYNC_8=y
BR2_TOOLCHAIN_HAS_LIBATOMIC=y
BR2_TOOLCHAIN_HAS_ATOMIC=y
#
# Bare metal toolchain
#
# BR2_TOOLCHAIN_BARE_METAL_BUILDROOT is not set
#
# Build options
#
#
# Commands
#
BR2_CURL="curl -q --ftp-pasv --retry 3"
BR2_WGET="wget -nd -t 3"
BR2_SVN="svn --non-interactive"
BR2_BZR="bzr"
BR2_GIT="git"
BR2_CVS="cvs"
BR2_LOCALFILES="cp"
BR2_SCP="scp"
BR2_SFTP="sftp"
BR2_HG="hg"
BR2_ZCAT="gzip -d -c"
BR2_BZCAT="bzcat"
BR2_XZCAT="xzcat"
BR2_LZCAT="lzip -d -c"
BR2_ZSTDCAT="zstdcat"
BR2_TAR_OPTIONS=""
BR2_DEFCONFIG="/home/neil/buildroot-2024.08/configs/freescale_imx8mmevk_defconfig"
BR2_DL_DIR="$(TOPDIR)/dl"
BR2_HOST_DIR="$(BASE_DIR)/host"
#
# Mirrors and Download locations
#
BR2_PRIMARY_SITE=""
BR2_BACKUP_SITE="https://sources.buildroot.net"
BR2_KERNEL_MIRROR="https://cdn.kernel.org/pub"
BR2_GNU_MIRROR="http://ftpmirror.gnu.org"
BR2_LUAROCKS_MIRROR="http://rocks.moonscript.org"
BR2_CPAN_MIRROR="https://cpan.metacpan.org"
BR2_JLEVEL=0
# BR2_CCACHE is not set
# BR2_ENABLE_DEBUG is not set
# BR2_ENABLE_RUNTIME_DEBUG is not set
BR2_STRIP_strip=y
BR2_STRIP_EXCLUDE_FILES=""
BR2_STRIP_EXCLUDE_DIRS=""
# BR2_OPTIMIZE_0 is not set
# BR2_OPTIMIZE_1 is not set
BR2_OPTIMIZE_2=y
# BR2_OPTIMIZE_3 is not set
# BR2_OPTIMIZE_G is not set
# BR2_OPTIMIZE_S is not set
# BR2_OPTIMIZE_FAST is not set
# BR2_ENABLE_LTO is not set
#
# static only needs a toolchain w/ uclibc or musl
#
BR2_SHARED_LIBS=y
# BR2_SHARED_STATIC_LIBS is not set
BR2_PACKAGE_OVERRIDE_FILE="$(CONFIG_DIR)/local.mk"
BR2_GLOBAL_PATCH_DIR="board/freescale/imx8mmevk/patches"
#
# Advanced
#
# BR2_FORCE_HOST_BUILD is not set
BR2_DOWNLOAD_FORCE_CHECK_HASHES=y
# BR2_REPRODUCIBLE is not set
# BR2_PER_PACKAGE_DIRECTORIES is not set
#
# Security Hardening Options
#
BR2_PIC_PIE_ARCH_SUPPORTS=y
BR2_PIC_PIE=y
# BR2_SSP_NONE is not set
# BR2_SSP_REGULAR is not set
BR2_SSP_STRONG=y
# BR2_SSP_ALL is not set
BR2_SSP_OPTION="-fstack-protector-strong"
# BR2_RELRO_NONE is not set
# BR2_RELRO_PARTIAL is not set
BR2_RELRO_FULL=y
BR2_FORTIFY_SOURCE_ARCH_SUPPORTS=y
# BR2_FORTIFY_SOURCE_NONE is not set
BR2_FORTIFY_SOURCE_1=y
# BR2_FORTIFY_SOURCE_2 is not set
# BR2_FORTIFY_SOURCE_3 is not set
#
# System configuration
#
BR2_ROOTFS_SKELETON_DEFAULT=y
# BR2_ROOTFS_SKELETON_CUSTOM is not set
BR2_TARGET_GENERIC_HOSTNAME="buildroot"
BR2_TARGET_GENERIC_ISSUE="Welcome to Buildroot"
BR2_TARGET_GENERIC_PASSWD_SHA256=y
# BR2_TARGET_GENERIC_PASSWD_SHA512 is not set
BR2_TARGET_GENERIC_PASSWD_METHOD="sha-256"
BR2_INIT_BUSYBOX=y
# BR2_INIT_SYSV is not set
# BR2_INIT_OPENRC is not set
# BR2_INIT_SYSTEMD is not set
# BR2_INIT_NONE is not set
# BR2_ROOTFS_DEVICE_CREATION_STATIC is not set
BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_DEVTMPFS=y
# BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_MDEV is not set
# BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV is not set
BR2_ROOTFS_DEVICE_TABLE="system/device_table.txt"
# BR2_ROOTFS_DEVICE_TABLE_SUPPORTS_EXTENDED_ATTRIBUTES is not set
# BR2_ROOTFS_MERGED_USR is not set
BR2_TARGET_ENABLE_ROOT_LOGIN=y
BR2_TARGET_GENERIC_ROOT_PASSWD=""
BR2_SYSTEM_BIN_SH_BUSYBOX=y
#
# bash, dash, mksh, zsh need BR2_PACKAGE_BUSYBOX_SHOW_OTHERS
#
# BR2_SYSTEM_BIN_SH_NONE is not set
BR2_TARGET_GENERIC_GETTY=y
BR2_TARGET_GENERIC_GETTY_PORT="ttymxc0"
# BR2_TARGET_GENERIC_GETTY_BAUDRATE_KEEP is not set
# BR2_TARGET_GENERIC_GETTY_BAUDRATE_9600 is not set
# BR2_TARGET_GENERIC_GETTY_BAUDRATE_19200 is not set
# BR2_TARGET_GENERIC_GETTY_BAUDRATE_38400 is not set
# BR2_TARGET_GENERIC_GETTY_BAUDRATE_57600 is not set
BR2_TARGET_GENERIC_GETTY_BAUDRATE_115200=y
BR2_TARGET_GENERIC_GETTY_BAUDRATE="115200"
BR2_TARGET_GENERIC_GETTY_TERM="vt100"
BR2_TARGET_GENERIC_GETTY_OPTIONS=""
BR2_TARGET_GENERIC_REMOUNT_ROOTFS_RW=y
BR2_SYSTEM_DHCP=""
BR2_SYSTEM_DEFAULT_PATH="/bin:/sbin:/usr/bin:/usr/sbin"
BR2_ENABLE_LOCALE_PURGE=y
BR2_ENABLE_LOCALE_WHITELIST="C en_US"
BR2_GENERATE_LOCALE=""
# BR2_SYSTEM_ENABLE_NLS is not set
# BR2_TARGET_TZ_INFO is not set
BR2_ROOTFS_USERS_TABLES=""
BR2_ROOTFS_OVERLAY=""
BR2_ROOTFS_PRE_BUILD_SCRIPT=""
BR2_ROOTFS_POST_BUILD_SCRIPT=""
BR2_ROOTFS_POST_FAKEROOT_SCRIPT=""
BR2_ROOTFS_POST_IMAGE_SCRIPT="board/freescale/common/imx/imx8-bootloader-prepare.sh board/freescale/common/imx/post-image.sh"
BR2_ROOTFS_POST_SCRIPT_ARGS="${UBOOT_DIR}/arch/arm/dts/imx8mm-evk.dtb"
BR2_ROOTFS_POST_IMAGE_SCRIPT_ARGS=""
#
# Kernel
#
BR2_LINUX_KERNEL=y
# BR2_LINUX_KERNEL_LATEST_VERSION is not set
# BR2_LINUX_KERNEL_LATEST_CIP_VERSION is not set
# BR2_LINUX_KERNEL_LATEST_CIP_RT_VERSION is not set
# BR2_LINUX_KERNEL_CUSTOM_VERSION is not set
BR2_LINUX_KERNEL_CUSTOM_TARBALL=y
# BR2_LINUX_KERNEL_CUSTOM_GIT is not set
# BR2_LINUX_KERNEL_CUSTOM_HG is not set
# BR2_LINUX_KERNEL_CUSTOM_SVN is not set
BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call github,nxp-imx,linux-imx,lf-6.1.1-1.0.0)/linux-imx-lf-6.1.1-1.0.0.tar.gz"
BR2_LINUX_KERNEL_VERSION="custom"
BR2_LINUX_KERNEL_PATCH=""
BR2_LINUX_KERNEL_USE_DEFCONFIG=y
# BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG is not set
# BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG is not set
BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES=""
BR2_LINUX_KERNEL_CUSTOM_LOGO_PATH=""
BR2_LINUX_KERNEL_IMAGE=y
# BR2_LINUX_KERNEL_IMAGEGZ is not set
# BR2_LINUX_KERNEL_VMLINUX is not set
# BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM is not set
BR2_LINUX_KERNEL_GZIP=y
# BR2_LINUX_KERNEL_LZ4 is not set
# BR2_LINUX_KERNEL_LZMA is not set
# BR2_LINUX_KERNEL_LZO is not set
# BR2_LINUX_KERNEL_XZ is not set
# BR2_LINUX_KERNEL_ZSTD is not set
BR2_LINUX_KERNEL_DTS_SUPPORT=y
# BR2_LINUX_KERNEL_DTB_IS_SELF_BUILT is not set
BR2_LINUX_KERNEL_INTREE_DTS_NAME=""
BR2_LINUX_KERNEL_CUSTOM_DTS_PATH="variscite/imx8mm-var-dart-dt8mcustomboard.dts variscite/imx8mm-var-dart.dtsi variscite/imx8mm.dtsi variscite/imx8mm-pinfunc.h variscite/mxl-8611x.h"
# BR2_LINUX_KERNEL_DTB_KEEP_DIRNAME is not set
# BR2_LINUX_KERNEL_DTB_OVERLAY_SUPPORT is not set
# BR2_LINUX_KERNEL_INSTALL_TARGET is not set
BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y
# BR2_LINUX_KERNEL_NEEDS_HOST_LIBELF is not set
# BR2_LINUX_KERNEL_NEEDS_HOST_PAHOLE is not set
#
# Linux Kernel Extensions
#
# BR2_LINUX_KERNEL_EXT_RTAI is not set
# BR2_LINUX_KERNEL_EXT_EV3DEV_LINUX_DRIVERS is not set
# BR2_LINUX_KERNEL_EXT_FBTFT is not set
# BR2_LINUX_KERNEL_EXT_AUFS is not set
#
# Linux Kernel Tools
#
# BR2_PACKAGE_LINUX_TOOLS_CPUPOWER is not set
# BR2_PACKAGE_LINUX_TOOLS_GPIO is not set
# BR2_PACKAGE_LINUX_TOOLS_IIO is not set
# BR2_PACKAGE_LINUX_TOOLS_MM is not set
# BR2_PACKAGE_LINUX_TOOLS_PCI is not set
# BR2_PACKAGE_LINUX_TOOLS_PERF is not set
# BR2_PACKAGE_LINUX_TOOLS_RTLA is not set
#
# selftests needs BR2_PACKAGE_BUSYBOX_SHOW_OTHERS and a toolchain w/ dynamic library and headers >= 3.14
#
# BR2_PACKAGE_LINUX_TOOLS_USBTOOLS is not set
# BR2_PACKAGE_LINUX_TOOLS_TMON is not set
#
# Target packages
#
BR2_PACKAGE_BUSYBOX=y
BR2_PACKAGE_BUSYBOX_CONFIG="package/busybox/busybox.config"
BR2_PACKAGE_BUSYBOX_CONFIG_FRAGMENT_FILES=""
# BR2_PACKAGE_BUSYBOX_SHOW_OTHERS is not set
# BR2_PACKAGE_BUSYBOX_INDIVIDUAL_BINARIES is not set
# BR2_PACKAGE_BUSYBOX_WATCHDOG is not set
BR2_PACKAGE_SKELETON=y
BR2_PACKAGE_HAS_SKELETON=y
BR2_PACKAGE_PROVIDES_SKELETON="skeleton-init-sysv"
BR2_PACKAGE_SKELETON_INIT_COMMON=y
BR2_PACKAGE_SKELETON_INIT_SYSV=y
#
# Audio and video applications
#
# BR2_PACKAGE_ALSA_UTILS is not set
# BR2_PACKAGE_ATEST is not set
# BR2_PACKAGE_AUMIX is not set
# BR2_PACKAGE_BLUEZ_ALSA is not set
# BR2_PACKAGE_DVBLAST is not set
# BR2_PACKAGE_DVDAUTHOR is not set
#
# dvdrw-tools needs a toolchain w/ threads, C++, wchar
#
#
# espeak needs a toolchain w/ C++, wchar, threads, dynamic library
#
# BR2_PACKAGE_FAAD2 is not set
BR2_PACKAGE_FFMPEG_ARCH_SUPPORTS=y
# BR2_PACKAGE_FFMPEG is not set
# BR2_PACKAGE_FLAC is not set
# BR2_PACKAGE_FLITE is not set
# BR2_PACKAGE_FLUID_SOUNDFONT is not set
#
# fluidsynth needs a toolchain w/ threads, wchar, dynamic library, C++
#
# BR2_PACKAGE_GMRENDER_RESURRECT is not set
# BR2_PACKAGE_GSTREAMER1 is not set
# BR2_PACKAGE_JACK1 is not set
#
# jack2 needs a toolchain w/ threads, C++, dynamic library
#
BR2_PACKAGE_KODI_ARCH_SUPPORTS=y
#
# kodi needs python3 w/ .py modules, a uClibc or glibc toolchain w/ C++, threads, wchar, dynamic library, gcc >= 9.x, host gcc >= 9.x
#
#
# kodi needs udev support for gbm
#
#
# kodi needs an OpenGL EGL backend with OpenGL or GLES support
#
# BR2_PACKAGE_LAME is not set
# BR2_PACKAGE_MADPLAY is not set
# BR2_PACKAGE_MIMIC is not set
# BR2_PACKAGE_MINIMODEM is not set
#
# miraclecast needs systemd and a glibc toolchain w/ threads and wchar
#
#
# mjpegtools needs a toolchain w/ C++, threads
#
#
# modplugtools needs a toolchain w/ C++
#
# BR2_PACKAGE_MOTION is not set
#
# mpd needs a toolchain w/ C++, threads, wchar, gcc >= 8, host gcc >= 8
#
# BR2_PACKAGE_MPD_MPC is not set
# BR2_PACKAGE_MPG123 is not set
#
# mpv needs a toolchain w/ C++, NPTL, gcc >= 4.9
#
# BR2_PACKAGE_MULTICAT is not set
# BR2_PACKAGE_MUSEPACK is not set
#
# ncmpc needs a toolchain w/ C++, wchar, threads, gcc >= 10
#
# BR2_PACKAGE_OPUS_TOOLS is not set
# BR2_PACKAGE_PIPEWIRE is not set
BR2_PACKAGE_PULSEAUDIO_HAS_ATOMIC=y
# BR2_PACKAGE_PULSEAUDIO is not set
# BR2_PACKAGE_SOX is not set
# BR2_PACKAGE_SPEECHD is not set
# BR2_PACKAGE_SQUEEZELITE is not set
# BR2_PACKAGE_TINYCOMPRESS is not set
# BR2_PACKAGE_TSTOOLS is not set
# BR2_PACKAGE_TWOLAME is not set
# BR2_PACKAGE_UDPXY is not set
#
# upmpdcli needs a toolchain w/ C++, NPTL, gcc >= 4.9
#
#
# v4l2grab needs a toolchain w/ threads, dynamic library, C++ and headers >= 3.0
#
# BR2_PACKAGE_V4L2LOOPBACK is not set
#
# vlc needs a toolchain w/ C++, dynamic library, wchar, threads, gcc >= 4.9, headers >= 3.7
#
# BR2_PACKAGE_VORBIS_TOOLS is not set
# BR2_PACKAGE_WAVPACK is not set
# BR2_PACKAGE_YAVTA is not set
# BR2_PACKAGE_YMPD is not set
#
# zynaddsubfx needs a toolchain w/ C++11 and threads
#
#
# Compressors and decompressors
#
# BR2_PACKAGE_BROTLI is not set
# BR2_PACKAGE_BZIP2 is not set
#
# lrzip needs a toolchain w/ wchar, threads, C++
#
#
# lzip needs a toolchain w/ C++
#
# BR2_PACKAGE_LZOP is not set
#
# p7zip needs a toolchain w/ threads, wchar, C++
#
# BR2_PACKAGE_PIGZ is not set
# BR2_PACKAGE_PIXZ is not set
#
# unrar needs a toolchain w/ C++, wchar, threads, gcc >= 4.8
#
# BR2_PACKAGE_XZ is not set
# BR2_PACKAGE_ZIP is not set
# BR2_PACKAGE_ZSTD is not set
#
# Debugging, profiling and benchmark
#
# BR2_PACKAGE_BABELTRACE2 is not set
#
# bcc needs a glibc toolchain, C++, wchar, threads, dynamic libs, gcc >= 7, host gcc >= 7
#
# BR2_PACKAGE_BLKTRACE is not set
#
# bonnie++ needs a toolchain w/ C++
#
BR2_PACKAGE_BPFTOOL_ARCH_SUPPORTS=y
# BR2_PACKAGE_BPFTOOL is not set
BR2_PACKAGE_BPFTRACE_ARCH_SUPPORTS=y
#
# bpftrace needs a glibc toolchain w/ C++, gcc >= 7, host gcc >= 7, kernel headers >= 4.13
#
# BR2_PACKAGE_CACHE_CALIBRATOR is not set
#
# clinfo needs an OpenCL provider
#
#
# clpeak needs an OpenCL provider, a toolchain w/ C++, gcc >= 4.8
#
# BR2_PACKAGE_COREMARK is not set
# BR2_PACKAGE_COREMARK_PRO is not set
#
# dacapo needs OpenJDK
#
BR2_PACKAGE_DELVE_ARCH_SUPPORTS=y
# BR2_PACKAGE_DELVE is not set
# BR2_PACKAGE_DHRYSTONE is not set
# BR2_PACKAGE_DIEHARDER is not set
# BR2_PACKAGE_DMALLOC is not set
# BR2_PACKAGE_DROPWATCH is not set
# BR2_PACKAGE_DSTAT is not set
# BR2_PACKAGE_DT is not set
#
# duma needs a toolchain w/ C++, threads, dynamic library
#
# BR2_PACKAGE_FIO is not set
BR2_PACKAGE_FWTS_ARCH_SUPPORTS=y
# BR2_PACKAGE_FWTS is not set
BR2_PACKAGE_GDB_ARCH_SUPPORTS=y
#
# gdb/gdbserver >= 8.x needs a toolchain w/ C++, gcc >= 4.8
#
BR2_PACKAGE_GOOGLE_BREAKPAD_ARCH_SUPPORTS=y
#
# google-breakpad requires a glibc toolchain w/ wchar, threads, C++, gcc >= 7
#
# BR2_PACKAGE_HYPERFINE is not set
# BR2_PACKAGE_IOZONE is not set
BR2_PACKAGE_KEXEC_ARCH_SUPPORTS=y
# BR2_PACKAGE_KEXEC is not set
# BR2_PACKAGE_KMEMD is not set
# BR2_PACKAGE_LATENCYTOP is not set
# BR2_PACKAGE_LIBBPF is not set
# BR2_PACKAGE_LIBTRACEEVENT is not set
# BR2_PACKAGE_LIBTRACEFS is not set
# BR2_PACKAGE_LMBENCH is not set
BR2_PACKAGE_LTP_TESTSUITE_ARCH_SUPPORTS=y
# BR2_PACKAGE_LTP_TESTSUITE is not set
BR2_PACKAGE_LTRACE_ARCH_SUPPORTS=y
# BR2_PACKAGE_LTRACE is not set
# BR2_PACKAGE_LTTNG_BABELTRACE is not set
# BR2_PACKAGE_LTTNG_MODULES is not set
#
# lttng-tools needs a toolchain w/ threads, dynamic library, C++
#
# BR2_PACKAGE_MBPOLL is not set
# BR2_PACKAGE_MBW is not set
# BR2_PACKAGE_MEMSTAT is not set
# BR2_PACKAGE_NETPERF is not set
#
# netsniff-ng needs a toolchain w/ NPTL, C++, headers >= 3.0
#
# BR2_PACKAGE_NMON is not set
BR2_PACKAGE_OPROFILE_ARCH_SUPPORTS=y
#
# oprofile needs a toolchain w/ C++, wchar
#
# BR2_PACKAGE_PAX_UTILS is not set
BR2_PACKAGE_PERFTEST_ARCH_SUPPORTS=y
# BR2_PACKAGE_PERFTEST is not set
#
# piglit needs a glibc or musl toolchain w/ C++, gcc >= 9, host gcc >= 9
#
BR2_PACKAGE_PLY_ARCH_SUPPORTS=y
# BR2_PACKAGE_PLY is not set
# BR2_PACKAGE_POKE is not set
BR2_PACKAGE_PTM2HUMAN_ARCH_SUPPORTS=y
# BR2_PACKAGE_PTM2HUMAN is not set
# BR2_PACKAGE_PV is not set
# BR2_PACKAGE_RAMSMP is not set
# BR2_PACKAGE_RAMSPEED is not set
# BR2_PACKAGE_RT_TESTS is not set
#
# rwmem needs a toolchain w/ C++, wchar, gcc >= 10
#
#
# sentry-native needs a glibc toolchain with w/ wchar, threads, C++, gcc >= 7
#
#
# signal-estimator needs a toochain w/ C++, threads, gcc >= 7
#
# BR2_PACKAGE_SPIDEV_TEST is not set
# BR2_PACKAGE_STRACE is not set
# BR2_PACKAGE_STRESS is not set
# BR2_PACKAGE_STRESS_NG is not set
#
# sysdig needs a glibc toolchain w/ C++, threads, gcc >= 8, dynamic library, a Linux kernel, and luajit or lua 5.1 to be built
#
#
# sysprof needs a toolchain w/ dynamic library, wchar, threads, C++, gcc >= 7, headers >= 5.12
#
#
# tbtools needs udev /dev management w/ glibc toolchain
#
# BR2_PACKAGE_TCF_AGENT is not set
BR2_PACKAGE_TCF_AGENT_ARCH="a64"
BR2_PACKAGE_TCF_AGENT_ARCH_SUPPORTS=y
# BR2_PACKAGE_TRACE_CMD is not set
BR2_PACKAGE_TRINITY_ARCH_SUPPORTS=y
# BR2_PACKAGE_TRINITY is not set
# BR2_PACKAGE_UCLIBC_NG_TEST is not set
BR2_PACKAGE_UFTRACE_ARCH_SUPPORTS=y
# BR2_PACKAGE_UFTRACE is not set
BR2_PACKAGE_VALGRIND_ARCH_SUPPORTS=y
# BR2_PACKAGE_VALGRIND is not set
# BR2_PACKAGE_VMTOUCH is not set
# BR2_PACKAGE_WHETSTONE is not set
#
# Development tools
#
# BR2_PACKAGE_AVOCADO is not set
# BR2_PACKAGE_BINUTILS is not set
# BR2_PACKAGE_BITWISE is not set
# BR2_PACKAGE_BSDIFF is not set
# BR2_PACKAGE_CHECK is not set
BR2_PACKAGE_CMAKE_ARCH_SUPPORTS=y
#
# ctest needs a toolchain w/ C++, wchar, dynamic library, gcc >= 4.9, NPTL
#
#
# cppunit needs a toolchain w/ C++, dynamic library
#
# BR2_PACKAGE_CUKINIA is not set
# BR2_PACKAGE_CUNIT is not set
# BR2_PACKAGE_CVS is not set
#
# cxxtest needs a toolchain w/ C++ support
#
# BR2_PACKAGE_FD is not set
# BR2_PACKAGE_FLEX is not set
# BR2_PACKAGE_GETTEXT is not set
BR2_PACKAGE_PROVIDES_HOST_GETTEXT="host-gettext-tiny"
# BR2_PACKAGE_GIT is not set
#
# git-crypt needs a toolchain w/ C++, gcc >= 4.9
#
#
# gperf needs a toolchain w/ C++
#
# BR2_PACKAGE_JO is not set
# BR2_PACKAGE_JQ is not set
# BR2_PACKAGE_LIBTOOL is not set
# BR2_PACKAGE_MAKE is not set
# BR2_PACKAGE_MAWK is not set
# BR2_PACKAGE_PKGCONF is not set
# BR2_PACKAGE_RIPGREP is not set
# BR2_PACKAGE_SUBVERSION is not set
# BR2_PACKAGE_TIG is not set
# BR2_PACKAGE_TREE is not set
# BR2_PACKAGE_UNIFDEF is not set
#
# Filesystem and flash utilities
#
# BR2_PACKAGE_ABOOTIMG is not set
# BR2_PACKAGE_AUFS_UTIL is not set
# BR2_PACKAGE_AUTOFS is not set
# BR2_PACKAGE_BTRFS_PROGS is not set
# BR2_PACKAGE_CIFS_UTILS is not set
# BR2_PACKAGE_CPIO is not set
# BR2_PACKAGE_CRAMFS is not set
# BR2_PACKAGE_CURLFTPFS is not set
# BR2_PACKAGE_DAVFS2 is not set
# BR2_PACKAGE_DOSFSTOOLS is not set
# BR2_PACKAGE_DUST is not set
# BR2_PACKAGE_E2FSPROGS is not set
# BR2_PACKAGE_E2TOOLS is not set
# BR2_PACKAGE_ECRYPTFS_UTILS is not set
# BR2_PACKAGE_EROFS_UTILS is not set
# BR2_PACKAGE_EXFAT is not set
# BR2_PACKAGE_EXFAT_UTILS is not set
# BR2_PACKAGE_EXFATPROGS is not set
# BR2_PACKAGE_F2FS_TOOLS is not set
# BR2_PACKAGE_FIRMWARE_UTILS is not set
# BR2_PACKAGE_FLASHBENCH is not set
# BR2_PACKAGE_FSCRYPTCTL is not set
# BR2_PACKAGE_FUSE_OVERLAYFS is not set
# BR2_PACKAGE_FWUP is not set
# BR2_PACKAGE_GENEXT2FS is not set
# BR2_PACKAGE_GENPART is not set
# BR2_PACKAGE_GENROMFS is not set
# BR2_PACKAGE_GOCRYPTFS is not set
# BR2_PACKAGE_IMX_USB_LOADER is not set
# BR2_PACKAGE_MMC_UTILS is not set
# BR2_PACKAGE_MTD is not set
# BR2_PACKAGE_MTOOLS is not set
# BR2_PACKAGE_NFS_UTILS is not set
# BR2_PACKAGE_NILFS_UTILS is not set
# BR2_PACKAGE_NTFS_3G is not set
# BR2_PACKAGE_SP_OOPS_EXTRACT is not set
# BR2_PACKAGE_SQUASHFS is not set
# BR2_PACKAGE_SSHFS is not set
# BR2_PACKAGE_UDFTOOLS is not set
# BR2_PACKAGE_UNIONFS is not set
#
# xfsprogs needs a toolchain w/ threads, C++
#
# BR2_PACKAGE_ZEROFREE is not set
#
# zfs needs udev /dev management
#
#
# Fonts, cursors, icons, sounds and themes
#
#
# Cursors
#
# BR2_PACKAGE_COMIX_CURSORS is not set
# BR2_PACKAGE_OBSIDIAN_CURSORS is not set
#
# Fonts
#
# BR2_PACKAGE_BITSTREAM_VERA is not set
# BR2_PACKAGE_CANTARELL is not set
# BR2_PACKAGE_DEJAVU is not set
# BR2_PACKAGE_FONT_AWESOME is not set
# BR2_PACKAGE_GHOSTSCRIPT_FONTS is not set
# BR2_PACKAGE_INCONSOLATA is not set
# BR2_PACKAGE_LIBERATION is not set
# BR2_PACKAGE_WQY_ZENHEI is not set
#
# Icons
#
# BR2_PACKAGE_HICOLOR_ICON_THEME is not set
#
# Sounds
#
# BR2_PACKAGE_SOUND_THEME_BOREALIS is not set
# BR2_PACKAGE_SOUND_THEME_FREEDESKTOP is not set
#
# Themes
#
#
# Games
#
# BR2_PACKAGE_ASCII_INVADERS is not set
# BR2_PACKAGE_CHOCOLATE_DOOM is not set
#
# flare-engine needs a toolchain w/ C++, dynamic library
#
#
# gnuchess needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LBREAKOUT2 is not set
# BR2_PACKAGE_LTRIS is not set
#
# minetest needs a toolchain w/ C++, gcc >= 5.1, threads
#
# BR2_PACKAGE_OPENTYRIAN is not set
# BR2_PACKAGE_PRBOOM is not set
# BR2_PACKAGE_SL is not set
#
# solarus needs OpenGL and a toolchain w/ C++, gcc >= 4.9, NPTL, dynamic library, and luajit or lua 5.1
#
#
# stella needs a toolchain w/ dynamic library, C++, threads, gcc >= 7
#
# BR2_PACKAGE_XORCURSES is not set
#
# Graphic libraries and applications (graphic/text)
#
#
# Graphic applications
#
#
# cage needs udev, EGL and OpenGL ES support
#
#
# cog needs wpewebkit and a toolchain w/ threads
#
#
# dmenu-wayland needs a toolchain w/ wchar, threads, C++, dynamic library, gcc >= 4.9
#
#
# flutter packages need flutter-engine
#
#
# flutter-pi needs a glibc toolchain w/ wchar, C++, gcc >= 5, dynamic library, host gcc >= 5
#
#
# flutter-pi needs an OpenGL or OpenGLES backend
#
#
# flutter-pi needs GBM, systemd, and udev
#
# BR2_PACKAGE_FOOT is not set
# BR2_PACKAGE_FSWEBCAM is not set
# BR2_PACKAGE_GHOSTSCRIPT is not set
#
# glmark2 needs a toolchain w/ C++, gcc >= 4.9
#
#
# glslsandbox-player needs openGL ES and EGL driver
#
# BR2_PACKAGE_GNUPLOT is not set
#
# igt-gpu-tools needs udev /dev management and toolchain w/ threads, wchar, dynamic library, locale, headers >= 4.11
#
#
# ivi-homescreen needs a glibc toolchain w/ wchar, C++, gcc >= 8, dynamic library, host gcc >= 5
#
#
# ivi-homescreen needs an OpenGL or OpenGLES backend
#
# BR2_PACKAGE_JHEAD is not set
#
# kmscube needs EGL, GBM and OpenGL ES, and a toolchain w/ thread support
#
#
# libva-utils needs a toolchain w/ C++, threads, dynamic library
#
BR2_PACKAGE_NETSURF_ARCH_SUPPORTS=y
# BR2_PACKAGE_NETSURF is not set
# BR2_PACKAGE_PNGQUANT is not set
# BR2_PACKAGE_RRDTOOL is not set
#
# spirv-tools needs a toolchain w/ C++, dynamic library, gcc >= 8
#
#
# stellarium needs Qt5 and an OpenGL provider
#
#
# sway needs systemd, udev, EGL and OpenGL ES support
#
#
# sway needs a toolchain w/ wchar, threads, C++, dynamic library, gcc >= 4.9
#
# BR2_PACKAGE_SWAYBG is not set
#
# tesseract-ocr needs a toolchain w/ threads, C++, gcc >= 7, dynamic library, wchar
#
# BR2_PACKAGE_TINIFIER is not set
#
# Graphic libraries
#
#
# cegui needs a toolchain w/ C++, threads, dynamic library, wchar, gcc >= 5
#
#
# directfb needs a glibc or uClibc toolchain w/ C++, NPTL, gcc >= 4.5, dynamic library
#
#
# efl needs a toolchain w/ C++, dynamic library, gcc >= 4.9, host gcc >= 4.9, threads, wchar
#
# BR2_PACKAGE_FB_TEST_APP is not set
# BR2_PACKAGE_FBDUMP is not set
# BR2_PACKAGE_FBGRAB is not set
#
# fbterm needs a toolchain w/ C++, wchar, locale
#
# BR2_PACKAGE_FBV is not set
#
# freerdp needs a toolchain w/ wchar, dynamic library, threads, C++
#
# BR2_PACKAGE_GRAPHICSMAGICK is not set
# BR2_PACKAGE_IMAGEMAGICK is not set
# BR2_PACKAGE_LIBGLVND is not set
# BR2_PACKAGE_LINUX_FUSION is not set
#
# mesa3d needs a toolchain w/ gcc >=8, C++, NPTL, dynamic library
#
#
# ocrad needs a toolchain w/ C++
#
#
# ogre needs a toolchain w/ C++, dynamic library, gcc >= 4.8, threads, wchar
#
# BR2_PACKAGE_PSPLASH is not set
# BR2_PACKAGE_SDL is not set
# BR2_PACKAGE_SDL2 is not set
#
# spirv-headers needs a toolchain w/ C++
#
# BR2_PACKAGE_VULKAN_HEADERS is not set
#
# vulkan-loader needs a toolchain w/ C++, dynamic library, threads
#
#
# vulkan-tools needs a toolchain w/ C++, dynamic library, threads, gcc >= 4.9
#
#
# Other GUIs
#
BR2_PACKAGE_QT5_JSCORE_AVAILABLE=y
#
# Qt5 needs host g++ >= 5.0, and a toolchain w/ gcc >= 5.0, wchar, NPTL, C++, dynamic library
#
BR2_PACKAGE_QT6_ARCH_SUPPORTS=y
#
# qt6 needs a toolchain w/ C++, threads, wchar, dynamic library, gcc >= 8, host gcc >= 8
#
#
# tekui needs a Lua interpreter and a toolchain w/ threads, dynamic library
#
#
# weston needs udev and a toolchain w/ locale, threads, dynamic library, headers >= 3.0
#
# BR2_PACKAGE_XORG7 is not set
#
# apitrace needs a toolchain w/ C++, wchar, dynamic library, threads, gcc >= 7
#
#
# mupdf needs a toolchain w/ C++, gcc >= 4.9
#
#
# vte needs a uClibc or glibc toolchain w/ wchar, threads, C++, gcc >= 10
#
#
# vte needs an OpenGL or an OpenGL-EGL backend
#
# BR2_PACKAGE_XKEYBOARD_CONFIG is not set
#
# Hardware handling
#
#
# Firmware
#
# BR2_PACKAGE_ARMBIAN_FIRMWARE is not set
# BR2_PACKAGE_B43_FIRMWARE is not set
# BR2_PACKAGE_BRCMFMAC_SDIO_FIRMWARE_RPI is not set
# BR2_PACKAGE_LINUX_FIRMWARE is not set
# BR2_PACKAGE_MURATA_CYW_FW is not set
# BR2_PACKAGE_ODROIDC2_FIRMWARE is not set
# BR2_PACKAGE_QCOM_DB410C_FIRMWARE is not set
# BR2_PACKAGE_QORIQ_FM_UCODE is not set
# BR2_PACKAGE_RCW_SMARC_SAL28 is not set
# BR2_PACKAGE_RPI_FIRMWARE is not set
# BR2_PACKAGE_UX500_FIRMWARE is not set
# BR2_PACKAGE_WILC1000_FIRMWARE is not set
# BR2_PACKAGE_WILC3000_FIRMWARE is not set
# BR2_PACKAGE_WILINK_BT_FIRMWARE is not set
# BR2_PACKAGE_ZD1211_FIRMWARE is not set
# BR2_PACKAGE_18XX_TI_UTILS is not set
# BR2_PACKAGE_ACPICA is not set
# BR2_PACKAGE_ACPID is not set
#
# acpitool needs a toolchain w/ threads, C++, dynamic library
#
# BR2_PACKAGE_AER_INJECT is not set
# BR2_PACKAGE_ALTERA_STAPL is not set
#
# apcupsd needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_AVRDUDE is not set
#
# bcache-tools needs udev /dev management
#
#
# brickd needs udev /dev management, a toolchain w/ threads, wchar
#
# BR2_PACKAGE_BRLTTY is not set
#
# cc-tool needs a toolchain w/ C++, threads, wchar, gcc >= 4.9
#
# BR2_PACKAGE_CDRKIT is not set
BR2_PACKAGE_CPUBURN_ARM_ARCH_SUPPORTS=y
# BR2_PACKAGE_CPUBURN_ARM is not set
# BR2_PACKAGE_CRUCIBLE is not set
# BR2_PACKAGE_CRYPTSETUP is not set
# BR2_PACKAGE_CWIID is not set
# BR2_PACKAGE_DAHDI_LINUX is not set
# BR2_PACKAGE_DAHDI_TOOLS is not set
# BR2_PACKAGE_DBUS is not set
#
# dbusbroker needs systemd and a toolchain w/ threads
#
#
# dbus-cxx needs a toolchain w/ C++, threads, gcc >= 7 and dynamic library support
#
# BR2_PACKAGE_DFU_PROGRAMMER is not set
# BR2_PACKAGE_DFU_UTIL is not set
# BR2_PACKAGE_DMIDECODE is not set
# BR2_PACKAGE_DMRAID is not set
#
# dt-utils needs udev /dev management
#
# BR2_PACKAGE_DTBOCFG is not set
# BR2_PACKAGE_DTV_SCAN_TABLES is not set
# BR2_PACKAGE_DUMP1090 is not set
# BR2_PACKAGE_DVBSNOOP is not set
#
# edid-decode needs a toolchain w/ C++, gcc >= 4.7
#
# BR2_PACKAGE_ESP_HOSTED is not set
#
# espflash needs udev /dev management
#
#
# eudev needs eudev /dev management
#
# BR2_PACKAGE_EVEMU is not set
# BR2_PACKAGE_EVTEST is not set
# BR2_PACKAGE_FCONFIG is not set
BR2_PACKAGE_FLASHROM_ARCH_SUPPORTS=y
# BR2_PACKAGE_FLASHROM is not set
# BR2_PACKAGE_FMTOOLS is not set
# BR2_PACKAGE_FREEIPMI is not set
BR2_PACKAGE_FREESCALE_IMX=y
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX25_3STACK is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX27ADS is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX37_3STACK is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX50 is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX51 is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX53 is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX6Q is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX6S is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX6UL is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX7 is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8 is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8M is not set
BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8MM=y
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8MN is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8MP is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8ULP is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8X is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX8DXL is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX91 is not set
# BR2_PACKAGE_FREESCALE_IMX_PLATFORM_IMX93 is not set
BR2_PACKAGE_FREESCALE_IMX_PLATFORM="IMX8MM"
BR2_PACKAGE_FREESCALE_IMX_HAS_VPU_HANTRO=y
BR2_PACKAGE_FREESCALE_IMX_HAS_VIV_GPU=y
# BR2_PACKAGE_IMX_CODEC is not set
# BR2_PACKAGE_IMX_PARSER is not set
# BR2_PACKAGE_IMX_UUC is not set
#
# imx-vpu needs an i.MX platform with VPU support
#
# BR2_PACKAGE_IMX_VPU_HANTRO is not set
# BR2_PACKAGE_IMX_VPUWRAP is not set
#
# firmware-ele-imx needs an i.MX platform with EdgeLock Secure Enclave
#
BR2_PACKAGE_FIRMWARE_IMX=y
BR2_PACKAGE_FIRMWARE_IMX_SDMA_FW_NAME="imx7d"
BR2_PACKAGE_FIRMWARE_IMX_NEEDS_DDR_FW=y
BR2_PACKAGE_FIRMWARE_IMX_LPDDR4=y
# BR2_PACKAGE_FIRMWARE_IMX_DDR4 is not set
# BR2_PACKAGE_FIRMWARE_IMX_DDR3 is not set
BR2_PACKAGE_FIRMWARE_IMX_DDR_VERSION=""
BR2_PACKAGE_FIRMWARE_IMX_IMEM_LEN=0x8000
BR2_PACKAGE_FIRMWARE_IMX_DMEM_LEN=0x4000
#
# firmware-upower needs an i.MX platform with uPower
#
# BR2_PACKAGE_IMX_VPU_HANTRO_DAEMON is not set
# BR2_PACKAGE_IMX_VPU_HANTRO_VC is not set
# BR2_PACKAGE_IMX_GPU_G2D is not set
# BR2_PACKAGE_IMX_GPU_VIV is not set
# BR2_PACKAGE_KERNEL_MODULE_IMX_GPU_VIV is not set
# BR2_PACKAGE_FWUPD is not set
# BR2_PACKAGE_FWUPD_EFI is not set
# BR2_PACKAGE_FXLOAD is not set
# BR2_PACKAGE_GCNANO_BINARIES is not set
# BR2_PACKAGE_GPM is not set
# BR2_PACKAGE_GPSD is not set
#
# gptfdisk needs a toolchain w/ C++
#
# BR2_PACKAGE_GVFS is not set
# BR2_PACKAGE_HDDTEMP is not set
# BR2_PACKAGE_HWDATA is not set
# BR2_PACKAGE_HWLOC is not set
# BR2_PACKAGE_INPUT_EVENT_DAEMON is not set
# BR2_PACKAGE_IPMITOOL is not set
# BR2_PACKAGE_IRDA_UTILS is not set
# BR2_PACKAGE_KBD is not set
# BR2_PACKAGE_LCDPROC is not set
#
# ledmon needs udev and a toolchain w/ threads
#
#
# libiec61850 needs a toolchain w/ C++, threads, dynamic library
#
# BR2_PACKAGE_LIBMANETTE is not set
# BR2_PACKAGE_LIBUBOOTENV is not set
# BR2_PACKAGE_LIBUIO is not set
# BR2_PACKAGE_LINUX_BACKPORTS is not set
# BR2_PACKAGE_LINUX_SERIAL_TEST is not set
# BR2_PACKAGE_LINUXCONSOLETOOLS is not set
#
# lirc-tools needs a toolchain w/ threads, dynamic library, C++
#
# BR2_PACKAGE_LM_SENSORS is not set
#
# lshw needs a toolchain w/ C++, wchar
#
# BR2_PACKAGE_LSSCSI is not set
# BR2_PACKAGE_LSUIO is not set
# BR2_PACKAGE_LUKSMETA is not set
# BR2_PACKAGE_LVM2 is not set
# BR2_PACKAGE_MALI_DRIVER is not set
# BR2_PACKAGE_MBPFAN is not set
# BR2_PACKAGE_MDADM is not set
# BR2_PACKAGE_MDEVD is not set
# BR2_PACKAGE_MDIO_TOOLS is not set
# BR2_PACKAGE_MEMTESTER is not set
# BR2_PACKAGE_MEMTOOL is not set
# BR2_PACKAGE_MHZ is not set
# BR2_PACKAGE_MINICOM is not set
# BR2_PACKAGE_MXT_APP is not set
# BR2_PACKAGE_NANOCOM is not set
# BR2_PACKAGE_NEARD is not set
# BR2_PACKAGE_NVIDIA_MODPROBE is not set
# BR2_PACKAGE_NVIDIA_PERSISTENCED is not set
# BR2_PACKAGE_NVME is not set
# BR2_PACKAGE_OFONO is not set
#
# ola needs a toolchain w/ C++, threads, dynamic library, gcc >= 4.8
#
# BR2_PACKAGE_OPEN2300 is not set
#
# openfpgaloader needs a toolchain w/ threads, C++, gcc >= 4.9
#
# BR2_PACKAGE_OPENIPMI is not set
# BR2_PACKAGE_OPENOCD is not set
# BR2_PACKAGE_PARTED is not set
# BR2_PACKAGE_PCIUTILS is not set
# BR2_PACKAGE_PDBG is not set
# BR2_PACKAGE_PICOCOM is not set
#
# picotool needs a toolchain w/ C++, threads, gcc >= 4.9
#
# BR2_PACKAGE_PIGPIO is not set
#
# powertop needs a toolchain w/ C++, threads, wchar
#
# BR2_PACKAGE_PPS_TOOLS is not set
# BR2_PACKAGE_QORIQ_CADENCE_DP_FIRMWARE is not set
# BR2_PACKAGE_RASPI_GPIO is not set
# BR2_PACKAGE_RDMA_CORE is not set
# BR2_PACKAGE_READ_EDID is not set
# BR2_PACKAGE_RNG_TOOLS is not set
#
# rockchip-mali needs a glibc toolchain w/ C++, threads
#
# BR2_PACKAGE_ROCKCHIP_RKBIN is not set
#
# rpi-userland needs a toolchain w/ C++, threads, dynamic library
#
# BR2_PACKAGE_RS485CONF is not set
# BR2_PACKAGE_RTC_TOOLS is not set
# BR2_PACKAGE_RTL8188EU is not set
# BR2_PACKAGE_RTL8189ES is not set
# BR2_PACKAGE_RTL8189FS is not set
# BR2_PACKAGE_RTL8192EU is not set
# BR2_PACKAGE_RTL8723BU is not set
# BR2_PACKAGE_RTL8723DS is not set
# BR2_PACKAGE_RTL8723DS_BT is not set
# BR2_PACKAGE_RTL8812AU_AIRCRACK_NG is not set
# BR2_PACKAGE_RTL8821AU is not set
# BR2_PACKAGE_RTL8821CU is not set
# BR2_PACKAGE_RTL8822CS is not set
# BR2_PACKAGE_SANE_BACKENDS is not set
# BR2_PACKAGE_SDPARM is not set
BR2_PACKAGE_SEDUTIL_ARCH_SUPPORTS=y
#
# sedutil needs a toolchain w/ C++, gcc >= 4.8, headers >= 3.12
#
# BR2_PACKAGE_SETSERIAL is not set
# BR2_PACKAGE_SG3_UTILS is not set
# BR2_PACKAGE_SIGROK_CLI is not set
# BR2_PACKAGE_SISPMCTL is not set
#
# smartmontools needs a toolchain w/ C++
#
# BR2_PACKAGE_SMSTOOLS3 is not set
# BR2_PACKAGE_SPI_TOOLS is not set
# BR2_PACKAGE_SREDIRD is not set
# BR2_PACKAGE_STATSERIAL is not set
# BR2_PACKAGE_STM32FLASH is not set
# BR2_PACKAGE_SUNXI_MALI_UTGARD is not set
# BR2_PACKAGE_SYSSTAT is not set
# BR2_PACKAGE_TI_UIM is not set
# BR2_PACKAGE_TI_UTILS is not set
#
# tio needs lua (but not luajit)
#
# BR2_PACKAGE_TRIGGERHAPPY is not set
# BR2_PACKAGE_UBOOT_BOOTCOUNT is not set
# BR2_PACKAGE_UBOOT_TOOLS is not set
# BR2_PACKAGE_UBUS is not set
#
# udisks needs udev /dev management
#
# BR2_PACKAGE_UHUBCTL is not set
# BR2_PACKAGE_UMTPRD is not set
#
# upower needs udev /dev management
#
# BR2_PACKAGE_USB_MODESWITCH is not set
# BR2_PACKAGE_USB_MODESWITCH_DATA is not set
#
# usbguard needs a toolchain w/ C++, threads, dynamic library, gcc >= 8
#
#
# usbmount requires udev to be enabled
#
#
# usbutils needs udev /dev management and toolchain w/ threads, gcc >= 4.9
#
# BR2_PACKAGE_W_SCAN is not set
# BR2_PACKAGE_WILC_DRIVER is not set
# BR2_PACKAGE_WIPE is not set
# BR2_PACKAGE_XORRISO is not set
# BR2_PACKAGE_XR819_XRADIO is not set
#
# Interpreter languages and scripting
#
# BR2_PACKAGE_4TH is not set
# BR2_PACKAGE_CHICKEN is not set
# BR2_PACKAGE_ENSCRIPT is not set
BR2_PACKAGE_HOST_ERLANG_ARCH_SUPPORTS=y
BR2_PACKAGE_ERLANG_ARCH_SUPPORTS=y
# BR2_PACKAGE_ERLANG is not set
# BR2_PACKAGE_EXECLINE is not set
# BR2_PACKAGE_FICL is not set
# BR2_PACKAGE_GUILE is not set
# BR2_PACKAGE_HASERL is not set
# BR2_PACKAGE_JANET is not set
# BR2_PACKAGE_JIMTCL is not set
# BR2_PACKAGE_LUA is not set
BR2_PACKAGE_PROVIDES_HOST_LUAINTERPRETER="host-lua"
BR2_PACKAGE_LUAJIT_ARCH_SUPPORTS=y
# BR2_PACKAGE_LUAJIT is not set
# BR2_PACKAGE_MICROPYTHON is not set
# BR2_PACKAGE_MOARVM is not set
BR2_PACKAGE_HOST_MONO_ARCH_SUPPORTS=y
BR2_PACKAGE_MONO_ARCH_SUPPORTS=y
#
# mono needs a toolchain w/ C++, NPTL, dynamic library
#
BR2_PACKAGE_NODEJS_ARCH_SUPPORTS=y
#
# nodejs needs a toolchain w/ C++, dynamic library, NPTL, gcc >= 10, wchar, host gcc >= 10
#
#
# octave needs a toolchain w/ C++ and fortran, gcc >= 4.8
#
BR2_PACKAGE_HOST_OPENJDK_BIN_ARCH_SUPPORTS=y
BR2_PACKAGE_OPENJDK_ARCH_SUPPORTS=y
#
# openjdk needs X.Org
#
#
# openjdk needs glibc, and a toolchain w/ wchar, dynamic library, threads, C++, gcc >= 4.9, host gcc >= 4.9
#
# BR2_PACKAGE_PERL is not set
BR2_PACKAGE_PHP_ARCH_SUPPORTS=y
# BR2_PACKAGE_PHP is not set
# BR2_PACKAGE_PYTHON3 is not set
# BR2_PACKAGE_QUICKJS is not set
# BR2_PACKAGE_RUBY is not set
BR2_PACKAGE_SWIPL_ARCH_SUPPORTS=y
# BR2_PACKAGE_SWIPL is not set
# BR2_PACKAGE_TCL is not set
#
# Libraries
#
#
# Audio/Sound
#
# BR2_PACKAGE_ALSA_LIB is not set
#
# alure needs a toolchain w/ C++, gcc >= 4.9, NPTL, wchar
#
# BR2_PACKAGE_AUBIO is not set
# BR2_PACKAGE_BCG729 is not set
#
# caps needs a toolchain w/ C++, dynamic library
#
BR2_PACKAGE_FDK_AAC_ARCH_SUPPORTS=y
#
# fdk-aac needs a toolchain w/ C++
#
BR2_PACKAGE_GTKIOSTREAM_ARCH_SUPPORTS=y
#
# gtkiostream needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LIBAO is not set
# BR2_PACKAGE_LIBBROADVOICE is not set
# BR2_PACKAGE_LIBCANBERRA is not set
# BR2_PACKAGE_LIBCDAUDIO is not set
# BR2_PACKAGE_LIBCDDB is not set
# BR2_PACKAGE_LIBCDIO is not set
# BR2_PACKAGE_LIBCDIO_PARANOIA is not set
# BR2_PACKAGE_LIBCODEC2 is not set
# BR2_PACKAGE_LIBCUE is not set
# BR2_PACKAGE_LIBCUEFILE is not set
# BR2_PACKAGE_LIBEBUR128 is not set
# BR2_PACKAGE_LIBG7221 is not set
# BR2_PACKAGE_LIBGSM is not set
# BR2_PACKAGE_LIBID3TAG is not set
# BR2_PACKAGE_LIBILBC is not set
# BR2_PACKAGE_LIBLO is not set
# BR2_PACKAGE_LIBMAD is not set
#
# libmodplug needs a toolchain w/ C++
#
# BR2_PACKAGE_LIBMPDCLIENT is not set
#
# libopenmpt needs a toolchain w/ threads, C++, gcc >= 7
#
# BR2_PACKAGE_LIBREPLAYGAIN is not set
# BR2_PACKAGE_LIBSAMPLERATE is not set
#
# libsidplay2 needs a toolchain w/ C++
#
# BR2_PACKAGE_LIBSILK is not set
# BR2_PACKAGE_LIBSNDFILE is not set
#
# libsoundtouch needs a toolchain w/ C++
#
# BR2_PACKAGE_LIBSOXR is not set
# BR2_PACKAGE_LIBVORBIS is not set
# BR2_PACKAGE_LILV is not set
# BR2_PACKAGE_LV2 is not set
#
# mp4v2 needs a toolchain w/ C++
#
BR2_PACKAGE_OPENAL_ARCH_SUPPORTS=y
#
# openal needs a toolchain w/ NPTL, C++, gcc >= 4.9
#
#
# opencore-amr needs a toolchain w/ C++
#
# BR2_PACKAGE_OPUS is not set
# BR2_PACKAGE_OPUSFILE is not set
# BR2_PACKAGE_PORTAUDIO is not set
# BR2_PACKAGE_SBC is not set
# BR2_PACKAGE_SPANDSP is not set
# BR2_PACKAGE_SPEEX is not set
# BR2_PACKAGE_SPEEXDSP is not set
# BR2_PACKAGE_SRATOM is not set
#
# taglib needs a toolchain w/ C++, wchar
#
# BR2_PACKAGE_TINYALSA is not set
# BR2_PACKAGE_TREMOR is not set
# BR2_PACKAGE_VO_AACENC is not set
BR2_PACKAGE_WEBRTC_AUDIO_PROCESSING_ARCH_SUPPORTS=y
#
# webrtc-audio-processing needs a toolchain w/ C++, NPTL, dynamic library, gcc >= 8
#
#
# Compression and decompression
#
# BR2_PACKAGE_LIBARCHIVE is not set
# BR2_PACKAGE_LIBDEFLATE is not set
# BR2_PACKAGE_LIBJCAT is not set
# BR2_PACKAGE_LIBMSPACK is not set
#
# libsquish needs a toolchain w/ C++
#
# BR2_PACKAGE_LIBZIP is not set
# BR2_PACKAGE_LZ4 is not set
# BR2_PACKAGE_LZO is not set
# BR2_PACKAGE_MINIZIP is not set
# BR2_PACKAGE_MINIZIP_ZLIB is not set
#
# snappy needs a toolchain w/ C++
#
# BR2_PACKAGE_SZIP is not set
# BR2_PACKAGE_ZCHUNK is not set
BR2_PACKAGE_ZLIB_NG_ARCH_SUPPORTS=y
# BR2_PACKAGE_ZLIB is not set
BR2_PACKAGE_PROVIDES_HOST_ZLIB="host-libzlib"
# BR2_PACKAGE_ZZIPLIB is not set
#
# Crypto
#
# BR2_PACKAGE_BEARSSL is not set
BR2_PACKAGE_BOTAN_ARCH_SUPPORTS=y
#
# botan needs a toolchain w/ threads, C++, gcc >= 11
#
# BR2_PACKAGE_CA_CERTIFICATES is not set
# BR2_PACKAGE_CRYPTODEV_LINUX is not set
#
# cryptopp needs a toolchain w/ C++, dynamic library, wchar
#
# BR2_PACKAGE_GCR is not set
# BR2_PACKAGE_GNUTLS is not set
# BR2_PACKAGE_LIBARGON2 is not set
# BR2_PACKAGE_LIBASSUAN is not set
# BR2_PACKAGE_LIBB2 is not set
# BR2_PACKAGE_LIBGCRYPT is not set
BR2_PACKAGE_LIBGPG_ERROR_ARCH_SUPPORTS=y
# BR2_PACKAGE_LIBGPG_ERROR is not set
BR2_PACKAGE_LIBGPG_ERROR_SYSCFG="aarch64-unknown-linux-gnu"
# BR2_PACKAGE_LIBGPGME is not set
# BR2_PACKAGE_LIBKCAPI is not set
# BR2_PACKAGE_LIBKSBA is not set
# BR2_PACKAGE_LIBMD is not set
# BR2_PACKAGE_LIBMHASH is not set
# BR2_PACKAGE_LIBNSS is not set
#
# libolm needs a toolchain w/ C++, gcc >= 4.8
#
# BR2_PACKAGE_LIBP11 is not set
# BR2_PACKAGE_LIBSCRYPT is not set
# BR2_PACKAGE_LIBSECRET is not set
# BR2_PACKAGE_LIBSHA1 is not set
# BR2_PACKAGE_LIBSODIUM is not set
BR2_PACKAGE_LIBSPDM_CPU_FAMILY="aarch64"
BR2_PACKAGE_LIBSPDM_ARCH_SUPPORTS=y
# BR2_PACKAGE_LIBSPDM is not set
# BR2_PACKAGE_LIBSSH is not set
# BR2_PACKAGE_LIBSSH2 is not set
# BR2_PACKAGE_LIBTOMCRYPT is not set
# BR2_PACKAGE_LIBUECC is not set
# BR2_PACKAGE_LIBXCRYPT is not set
# BR2_PACKAGE_MBEDTLS is not set
# BR2_PACKAGE_NETTLE is not set
BR2_PACKAGE_LIBRESSL_ARCH_SUPPORTS=y
# BR2_PACKAGE_OPENSSL is not set
BR2_PACKAGE_PROVIDES_HOST_OPENSSL="host-libopenssl"
# BR2_PACKAGE_PARSEC_TOOL is not set
# BR2_PACKAGE_PKCS11_HELPER is not set
# BR2_PACKAGE_RHASH is not set
# BR2_PACKAGE_TINYDTLS is not set
# BR2_PACKAGE_TPM2_OPENSSL is not set
# BR2_PACKAGE_TPM2_PKCS11 is not set
# BR2_PACKAGE_TPM2_TSS is not set
# BR2_PACKAGE_TROUSERS is not set
# BR2_PACKAGE_USTREAM_SSL is not set
BR2_PACKAGE_WOLFSSL_ASM_SUPPORTS=y
# BR2_PACKAGE_WOLFSSL is not set
# BR2_PACKAGE_WOLFTPM is not set
#
# Database
#
# BR2_PACKAGE_BERKELEYDB is not set
# BR2_PACKAGE_GDBM is not set
# BR2_PACKAGE_HIREDIS is not set
#
# kompexsqlite needs a toolchain w/ C++, wchar, threads, dynamic library
#
#
# leveldb needs a toolchain w/ C++, threads, gcc >= 4.8
#
# BR2_PACKAGE_LIBDBI is not set
# BR2_PACKAGE_LIBDBI_DRIVERS is not set
# BR2_PACKAGE_LIBGIT2 is not set
# BR2_PACKAGE_LIBMDBX is not set
#
# libodb needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LMDB is not set
#
# mariadb needs a toolchain w/ dynamic library, C++, threads, wchar
#
BR2_PACKAGE_MONGODB_ARCH_SUPPORTS=y
#
# mongodb needs a glibc toolchain w/ wchar, threads, C++, gcc >= 7
#
# BR2_PACKAGE_POSTGRESQL is not set
# BR2_PACKAGE_REDIS is not set
#
# redis-plus-plus needs a toolchain w/ C++, threads
#
BR2_PACKAGE_ROCKSDB_ARCH_SUPPORTS=y
#
# rocksdb needs a toolchain w/ C++, threads, wchar, gcc >= 4.8
#
# BR2_PACKAGE_SQLCIPHER is not set
# BR2_PACKAGE_SQLITE is not set
#
# sqlitecpp needs a toolchain w/ C++11, gcc >= 4.9
#
# BR2_PACKAGE_UNIXODBC is not set
#
# Filesystem
#
# BR2_PACKAGE_LIBCONFIG is not set
# BR2_PACKAGE_LIBCONFUSE is not set
# BR2_PACKAGE_LIBFUSE is not set
# BR2_PACKAGE_LIBFUSE3 is not set
# BR2_PACKAGE_LIBLOCKFILE is not set
# BR2_PACKAGE_LIBNFS is not set
# BR2_PACKAGE_LIBSYSFS is not set
# BR2_PACKAGE_LOCKDEV is not set
#
# physfs needs a toolchain w/ C++, threads
#
#
# Graphics
#
#
# assimp needs a toolchain w/ C++, wchar, gcc >= 7
#
# BR2_PACKAGE_AT_SPI2_CORE is not set
#
# atkmm needs a toolchain w/ C++, wchar, threads, gcc >= 7
#
#
# atkmm (2.28.x) needs a toolchain w/ C++, wchar, threads, gcc >= 4.9
#
BR2_PACKAGE_BAYER2RGB_NEON_ARCH_SUPPORTS=y
#
# bayer2rgb-neon needs a toolchain w/ C++, dynamic library, gcc >= 4.9
#
#
# bullet needs a toolchain w/ C++, dynamic library, threads, wchar
#
# BR2_PACKAGE_CAIRO is not set
#
# cairomm needs a toolchain w/ C++, wchar, threads, gcc >= 7
#
#
# cairomm (1.14.x) needs a toolchain w/ C++, wchar, threads, gcc >= 4.9
#
#
# chipmunk needs an OpenGL backend
#
#
# exempi needs a toolchain w/ C++, dynamic library, threads, wchar
#
#
# exiv2 needs a uClibc or glibc toolchain w/ C++, wchar, dynamic library, threads
#
BR2_PACKAGE_FLUTTER_ENGINE_ARCH_SUPPORTS=y
#
# flutter-engine needs an OpenGL or OpenGLES backend
#
#
# flutter-engine needs a glibc toolchain w/ wchar, C++, gcc >= 5, dynamic library, host gcc >= 5
#
# BR2_PACKAGE_FONTCONFIG is not set
# BR2_PACKAGE_FREETYPE is not set
# BR2_PACKAGE_GD is not set
# BR2_PACKAGE_GDK_PIXBUF is not set
# BR2_PACKAGE_GIFLIB is not set
#
# granite needs libgtk3 and a toolchain w/ wchar, threads, gcc >= 4.9
#
# BR2_PACKAGE_GRAPHENE is not set
#
# graphite2 needs a toolchain w/ C++
#
#
# gtkmm3 needs libgtk3 and a toolchain w/ C++, wchar, threads, gcc >= 4.9
#
#
# harfbuzz needs a toolchain w/ C++, gcc >= 4.9
#
# BR2_PACKAGE_IJS is not set
# BR2_PACKAGE_IMLIB2 is not set
#
# intel-gmmlib needs a toolchain w/ dynamic library, C++, threads
#
#
# irrlicht needs a toolchain w/ C++
#
# BR2_PACKAGE_JASPER is not set
# BR2_PACKAGE_JBIG2DEC is not set
BR2_PACKAGE_JPEG_SIMD_SUPPORT=y
# BR2_PACKAGE_JPEG is not set
#
# kms++ needs a toolchain w/ threads, C++, gcc >= 4.8, headers >= 4.11, wchar
#
# BR2_PACKAGE_LCMS2 is not set
#
# lensfun needs a toolchain w/ C++, threads, wchar
#
# BR2_PACKAGE_LEPTONICA is not set
# BR2_PACKAGE_LIBART is not set
# BR2_PACKAGE_LIBAVIF is not set
#
# libdecor needs a toolchain w/ wchar, threads, C++, gcc >= 4.9
#
# BR2_PACKAGE_LIBDMTX is not set
# BR2_PACKAGE_LIBDRM is not set
#
# libepoxy needs an OpenGL and/or OpenGL EGL backend
#
# BR2_PACKAGE_LIBEXIF is not set
#
# libfm needs X.org and a toolchain w/ wchar, threads, C++, gcc >= 4.9
#
# BR2_PACKAGE_LIBFM_EXTRA is not set
#
# libfreeglut depends on X.org and needs an OpenGL backend
#
#
# libfreeimage needs a toolchain w/ C++, dynamic library, wchar
#
#
# libgeotiff needs a toolchain w/ C++, gcc >= 4.7, NPTL, wchar
#
#
# libglew depends on X.org and needs an OpenGL backend
#
#
# libglfw depends on X.org or Wayland and an OpenGL or GLES backend
#
#
# libglu needs an OpenGL backend
#
# BR2_PACKAGE_LIBGTA is not set
#
# libgtk3 needs a toolchain w/ wchar, threads, C++, gcc >= 4.9
#
#
# libgtk3 needs an OpenGL or an OpenGL-EGL backend
#
#
# libgtk4 needs a toolchain w/ wchar, threads, C++, gcc >= 4.9
#
#
# libgtk4 needs an OpenGL(ES) EGL backend
#
#
# libjxl needs a toolchain with C++, threads, gcc >= 7, dynamic library
#
# BR2_PACKAGE_LIBMEDIAART is not set
# BR2_PACKAGE_LIBMNG is not set
# BR2_PACKAGE_LIBPNG is not set
# BR2_PACKAGE_LIBQRENCODE is not set
#
# libraw needs a toolchain w/ C++
#
#
# librsvg needs a toolchain w/ wchar, threads, C++, gcc >= 4.9
#
# BR2_PACKAGE_LIBSVG is not set
# BR2_PACKAGE_LIBSVG_CAIRO is not set
# BR2_PACKAGE_LIBSVGTINY is not set
# BR2_PACKAGE_LIBVA is not set
#
# libvips needs a toolchain w/ wchar, threads, C++
#
BR2_PACKAGE_LIBVPL_ARCH_SUPPORTS=y
#
# libvpl needs a toolchain w/ dynamic library, gcc >= 7, C++, threads
#
#
# libwpe needs a toolchain w/ C++, dynamic library and an OpenEGL-capable backend
#
# BR2_PACKAGE_MENU_CACHE is not set
#
# opencv3 needs a toolchain w/ C++, NPTL, wchar, dynamic library
#
#
# opencv4 needs a toolchain w/ C++, NPTL, wchar, dynamic library, gcc >= 4.8
#
# BR2_PACKAGE_OPENJPEG is not set
#
# pango needs a toolchain w/ wchar, threads, C++, gcc >= 4.9
#
#
# pangomm needs a toolchain w/ C++, wchar, threads, gcc >= 7
#
#
# pangomm (2.46.x) needs a toolchain w/ C++, wchar, threads, gcc >= 4.9
#
# BR2_PACKAGE_PIXMAN is not set
#
# poppler needs a toolchain w/ wchar, C++, threads, dynamic library, gcc >= 7
#
# BR2_PACKAGE_STB is not set
# BR2_PACKAGE_TIFF is not set
# BR2_PACKAGE_WAYLAND is not set
BR2_PACKAGE_WEBKITGTK_ARCH_SUPPORTS=y
#
# webkitgtk needs libgtk3 and a toolchain w/ C++, wchar, threads, dynamic library, gcc >= 10, host gcc >= 4.9
#
# BR2_PACKAGE_WEBP is not set
#
# wlroots needs udev, EGL and OpenGL ES support
#
#
# woff2 needs a toolchain w/ C++
#
#
# wpebackend-fdo needs a toolchain w/ C++, wchar, threads, dynamic library and EGL support
#
BR2_PACKAGE_WPEWEBKIT_ARCH_SUPPORTS=y
#
# wpewebkit needs a toolchain w/ C++, wchar, threads, dynamic library, gcc >= 10, host gcc >= 4.9
#
#
# wpewebkit needs an OpenGL ES w/ EGL-capable Wayland backend
#
#
# zbar needs a toolchain w/ threads, C++ and headers >= 3.0
#
#
# zxing-cpp needs a toolchain w/ C++, wchar, dynamic library, threads
#
#
# Hardware handling
#
# BR2_PACKAGE_ACSCCID is not set
# BR2_PACKAGE_C_PERIPHERY is not set
# BR2_PACKAGE_CCID is not set
# BR2_PACKAGE_DTC is not set
BR2_PACKAGE_GNU_EFI_ARCH_SUPPORTS=y
# BR2_PACKAGE_GNU_EFI is not set
# BR2_PACKAGE_HACKRF is not set
#
# hidapi needs udev /dev management and a toolchain w/ NPTL, gcc >= 4.9
#
# BR2_PACKAGE_JITTERENTROPY_LIBRARY is not set
#
# lcdapi needs a toolchain w/ C++, threads
#
#
# let-me-create needs a toolchain w/ C++, threads, dynamic library
#
# BR2_PACKAGE_LIBAIO is not set
#
# libatasmart requires udev to be enabled
#
#
# libblockdev needs udev /dev management and a toolchain w/ wchar, threads, dynamic library, locale
#
#
# libcec needs a toolchain w/ C++, wchar, threads, dynamic library, gcc >= 4.7
#
# BR2_PACKAGE_LIBDISPLAY_INFO is not set
# BR2_PACKAGE_LIBFREEFARE is not set
# BR2_PACKAGE_LIBFTDI is not set
# BR2_PACKAGE_LIBFTDI1 is not set
# BR2_PACKAGE_LIBGPHOTO2 is not set
# BR2_PACKAGE_LIBGPIOD is not set
# BR2_PACKAGE_LIBGPIOD2 is not set
#
# libgudev needs udev /dev handling and a toolchain w/ wchar, threads
#
# BR2_PACKAGE_LIBHID is not set
# BR2_PACKAGE_LIBIIO is not set
#
# libinput needs udev /dev management
#
# BR2_PACKAGE_LIBIQRF is not set
# BR2_PACKAGE_LIBLLCP is not set
# BR2_PACKAGE_LIBMBIM is not set
# BR2_PACKAGE_LIBNFC is not set
# BR2_PACKAGE_LIBNVME is not set
# BR2_PACKAGE_LIBPCIACCESS is not set
# BR2_PACKAGE_LIBPHIDGET is not set
# BR2_PACKAGE_LIBPRI is not set
# BR2_PACKAGE_LIBQMI is not set
# BR2_PACKAGE_LIBQRTR_GLIB is not set
# BR2_PACKAGE_LIBRAW1394 is not set
# BR2_PACKAGE_LIBRTLSDR is not set
#
# libserial needs a toolchain w/ C++, gcc >= 5, threads, wchar
#
# BR2_PACKAGE_LIBSERIALPORT is not set
# BR2_PACKAGE_LIBSIGROK is not set
# BR2_PACKAGE_LIBSIGROKDECODE is not set
# BR2_PACKAGE_LIBSOC is not set
# BR2_PACKAGE_LIBSS7 is not set
# BR2_PACKAGE_LIBUSB is not set
# BR2_PACKAGE_LIBUSBGX is not set
#
# libv4l needs a toolchain w/ threads, C++ and headers >= 3.0
#
# BR2_PACKAGE_LIBXKBCOMMON is not set
BR2_PACKAGE_MRAA_ARCH_SUPPORTS=y
# BR2_PACKAGE_MRAA is not set
# BR2_PACKAGE_MTDEV is not set
BR2_PACKAGE_NE10_ARCH_SUPPORTS=y
# BR2_PACKAGE_NE10 is not set
# BR2_PACKAGE_NEARDAL is not set
BR2_PACKAGE_OPENCSD_ARCH_SUPPORTS=y
#
# opencsd needs a toolchain w/ C++11, gcc >= 4.8, dynamic library
#
# BR2_PACKAGE_OPENSC is not set
# BR2_PACKAGE_OWFS is not set
# BR2_PACKAGE_PCSC_LITE is not set
# BR2_PACKAGE_PICO_SDK is not set
#
# rpi-rgb-led-matrix needs a toolchain w/ C++, threads, dynamic library
#
# BR2_PACKAGE_TSLIB is not set
#
# uhd needs a toolchain w/ C++, NPTL, wchar, dynamic library, gcc >= 5
#
#
# urg needs a toolchain w/ C++
#
#
# Javascript
#
# BR2_PACKAGE_ANGULARJS is not set
# BR2_PACKAGE_BOOTSTRAP is not set
# BR2_PACKAGE_CHARTJS is not set
# BR2_PACKAGE_DATATABLES is not set
# BR2_PACKAGE_DUKTAPE is not set
# BR2_PACKAGE_EXPLORERCANVAS is not set
# BR2_PACKAGE_FLOT is not set
# BR2_PACKAGE_FORGE is not set
# BR2_PACKAGE_JQUERY is not set
# BR2_PACKAGE_JSMIN is not set
# BR2_PACKAGE_JSON_JAVASCRIPT is not set
# BR2_PACKAGE_JSZIP is not set
# BR2_PACKAGE_OPENLAYERS is not set
# BR2_PACKAGE_POPPERJS is not set
# BR2_PACKAGE_VIS_NETWORK is not set
# BR2_PACKAGE_VUEJS is not set
#
# JSON/XML
#
#
# benejson needs a toolchain w/ C++
#
# BR2_PACKAGE_CJSON is not set
# BR2_PACKAGE_EXPAT is not set
# BR2_PACKAGE_JANSSON is not set
# BR2_PACKAGE_JOSE is not set
# BR2_PACKAGE_JSMN is not set
# BR2_PACKAGE_JSON_C is not set
#
# json-for-modern-cpp needs a toolchain w/ C++, gcc >= 4.9
#
# BR2_PACKAGE_JSON_GLIB is not set
#
# jsoncpp needs a toolchain w/ C++, gcc >= 4.7
#
# BR2_PACKAGE_LIBBSON is not set
# BR2_PACKAGE_LIBFASTJSON is not set
#
# libjson needs a toolchain w/ C++
#
# BR2_PACKAGE_LIBJWT is not set
# BR2_PACKAGE_LIBROXML is not set
# BR2_PACKAGE_LIBUCL is not set
# BR2_PACKAGE_LIBXML2 is not set
# BR2_PACKAGE_LIBXMLB is not set
#
# libxml++ needs a toolchain w/ C++, wchar, threads, gcc >= 7
#
# BR2_PACKAGE_LIBXMLRPC is not set
# BR2_PACKAGE_LIBXSLT is not set
# BR2_PACKAGE_LIBYAML is not set
# BR2_PACKAGE_MXML is not set
#
# pugixml needs a toolchain w/ C++
#
#
# rapidjson needs a toolchain w/ C++
#
# BR2_PACKAGE_RAPIDXML is not set
# BR2_PACKAGE_RAPTOR is not set
# BR2_PACKAGE_SERD is not set
# BR2_PACKAGE_SORD is not set
#
# tinyxml needs a toolchain w/ C++
#
#
# tinyxml2 needs a toolchain w/ C++
#
#
# valijson needs a toolchain w/ C++
#
#
# xerces-c++ needs a toolchain w/ C++, dynamic library, wchar
#
#
# xml-security-c needs a toolchain w/ C++, wchar, dynamic library, threads, gcc >= 4.7
#
# BR2_PACKAGE_YAJL is not set
#
# yaml-cpp needs a toolchain w/ C++, gcc >= 4.7
#
#
# Logging
#
#
# glog needs a toolchain w/ C++, threads, gcc >= 6
#
#
# hawktracer needs a toolchain w/ C++, gcc >= 4.8
#
# BR2_PACKAGE_LIBLOG4C_LOCALTIME is not set
# BR2_PACKAGE_LIBLOGGING is not set
#
# log4cplus needs a toolchain w/ C++, wchar, threads, gcc >= 4.8
#
#
# log4cpp needs a toolchain w/ C++, threads
#
#
# log4cxx needs a toolchain w/ C++, threads, dynamic library
#
#
# log4qt needs qt5
#
#
# opentracing-cpp needs a toolchain w/ C++, threads, dynamic library, gcc >= 4.8
#
#
# spdlog needs a toolchain w/ C++, threads, wchar
#
#
# ulog needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_ZLOG is not set
#
# Multimedia
#
#
# bento4 support needs a toolchain with C++
#
# BR2_PACKAGE_BITSTREAM is not set
# BR2_PACKAGE_DAV1D is not set
#
# kvazaar needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LIBAACS is not set
#
# libass needs a toolchain w/ C++, gcc >= 4.9
#
# BR2_PACKAGE_LIBBDPLUS is not set
# BR2_PACKAGE_LIBBLURAY is not set
BR2_PACKAGE_LIBCAMERA_ARCH_SUPPORTS=y
#
# libcamera needs a toolchain w/ C++, threads, wchar, dynamic library, gcc >= 8
#
#
# libcamera-apps needs a toolchain w/ C++, threads, wchar, dynamic library, gcc >= 8, headers >= 5.5
#
#
# libde265 needs a toolchain w/ threads, C++
#
# BR2_PACKAGE_LIBDVBCSA is not set
# BR2_PACKAGE_LIBDVBPSI is not set
#
# libdvbsi++ needs a toolchain w/ C++, wchar, threads
#
# BR2_PACKAGE_LIBDVDCSS is not set
# BR2_PACKAGE_LIBDVDNAV is not set
# BR2_PACKAGE_LIBDVDREAD is not set
#
# libebml needs a toolchain w/ C++, wchar, gcc >= 4.9
#
# BR2_PACKAGE_LIBHDHOMERUN is not set
#
# libheif needs a toolchain w/ C++, gcc >= 4.8
#
#
# libmatroska needs a toolchain w/ C++, wchar, gcc >= 4.9
#
# BR2_PACKAGE_LIBMMS is not set
# BR2_PACKAGE_LIBMPEG2 is not set
# BR2_PACKAGE_LIBOGG is not set
# BR2_PACKAGE_LIBOPENAPTX is not set
BR2_PACKAGE_LIBOPENH264_ARCH_SUPPORTS=y
#
# libopenh264 needs a toolchain w/ C++, dynamic library, threads
#
# BR2_PACKAGE_LIBOPUSENC is not set
# BR2_PACKAGE_LIBTHEORA is not set
# BR2_PACKAGE_LIBUDFREAD is not set
# BR2_PACKAGE_LIBVPX is not set
#
# libyuv needs a toolchain w/ C++, dynamic library
#
#
# live555 needs a toolchain w/ C++
#
#
# mediastreamer needs a toolchain w/ threads, C++, dynamic library, gcc >= 5
#
# BR2_PACKAGE_X264 is not set
#
# x265 needs a toolchain w/ C++, threads, dynamic library
#
#
# Networking
#
#
# agent++ needs a toolchain w/ threads, C++, dynamic library
#
#
# azmq needs a toolchain w/ C++11, wchar and threads
#
#
# azure-iot-sdk-c needs a toolchain w/ C++, NPTL and wchar
#
# BR2_PACKAGE_BATMAN_ADV is not set
#
# belle-sip needs a toolchain w/ threads, C++, dynamic library, wchar
#
# BR2_PACKAGE_C_ARES is not set
# BR2_PACKAGE_CNI_PLUGINS is not set
#
# cppzmq needs a toolchain w/ C++, threads
#
#
# curlpp needs a toolchain w/ C++, dynamic library
#
#
# czmq needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_DAQ is not set
# BR2_PACKAGE_DAQ3 is not set
# BR2_PACKAGE_DAVICI is not set
# BR2_PACKAGE_DHT is not set
# BR2_PACKAGE_ENET is not set
#
# filemq needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_FMLIB is not set
# BR2_PACKAGE_FREERADIUS_CLIENT is not set
# BR2_PACKAGE_GENSIO is not set
# BR2_PACKAGE_GEOIP is not set
# BR2_PACKAGE_GLIB_NETWORKING is not set
#
# grpc needs a toolchain w/ C++, threads, dynamic library, gcc >= 8
#
# BR2_PACKAGE_GSSDP is not set
# BR2_PACKAGE_GUPNP is not set
# BR2_PACKAGE_GUPNP_AV is not set
# BR2_PACKAGE_GUPNP_DLNA is not set
#
# ibrcommon needs a toolchain w/ C++, threads
#
#
# ibrdtn needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LIBCGI is not set
#
# libcgicc needs a toolchain w/ C++
#
# BR2_PACKAGE_LIBCOAP is not set
#
# libcpprestsdk needs a toolchain w/ NPTL, C++, wchar, locale
#
# BR2_PACKAGE_LIBCURL is not set
# BR2_PACKAGE_LIBDNET is not set
# BR2_PACKAGE_LIBEXOSIP2 is not set
# BR2_PACKAGE_LIBEST is not set
# BR2_PACKAGE_LIBFCGI is not set
# BR2_PACKAGE_LIBGSASL is not set
# BR2_PACKAGE_LIBHTP is not set
# BR2_PACKAGE_LIBHTTPPARSER is not set
#
# libhttpserver needs a toolchain w/ C++, threads, gcc >= 7
#
# BR2_PACKAGE_LIBIDN is not set
# BR2_PACKAGE_LIBIDN2 is not set
# BR2_PACKAGE_LIBISCSI is not set
# BR2_PACKAGE_LIBKRB5 is not set
# BR2_PACKAGE_LIBLDNS is not set
# BR2_PACKAGE_LIBMAXMINDDB is not set
# BR2_PACKAGE_LIBMBUS is not set
#
# libmemcached needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LIBMICROHTTPD is not set
# BR2_PACKAGE_LIBMINIUPNPC is not set
# BR2_PACKAGE_LIBMNL is not set
# BR2_PACKAGE_LIBMODBUS is not set
#
# libmodsecurity needs a toolchain w/ C++, threads, dynamic library
#
# BR2_PACKAGE_LIBNATPMP is not set
# BR2_PACKAGE_LIBNDP is not set
# BR2_PACKAGE_LIBNET is not set
# BR2_PACKAGE_LIBNETCONF2 is not set
# BR2_PACKAGE_LIBNETFILTER_ACCT is not set
# BR2_PACKAGE_LIBNETFILTER_CONNTRACK is not set
# BR2_PACKAGE_LIBNETFILTER_CTHELPER is not set
# BR2_PACKAGE_LIBNETFILTER_CTTIMEOUT is not set
# BR2_PACKAGE_LIBNETFILTER_LOG is not set
# BR2_PACKAGE_LIBNETFILTER_QUEUE is not set
# BR2_PACKAGE_LIBNFNETLINK is not set
# BR2_PACKAGE_LIBNFTNL is not set
# BR2_PACKAGE_LIBNICE is not set
# BR2_PACKAGE_LIBNIDS is not set
# BR2_PACKAGE_LIBNL is not set
#
# libnpupnp needs a toolchain w/ C++, threads, gcc >= 4.9
#
# BR2_PACKAGE_LIBOAUTH is not set
# BR2_PACKAGE_LIBOPING is not set
# BR2_PACKAGE_LIBOSIP2 is not set
# BR2_PACKAGE_LIBPAGEKITE is not set
# BR2_PACKAGE_LIBPCAP is not set
#
# libpjsip needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LIBPSL is not set
# BR2_PACKAGE_LIBRELP is not set
# BR2_PACKAGE_LIBRSYNC is not set
# BR2_PACKAGE_LIBSHAIRPLAY is not set
# BR2_PACKAGE_LIBSHOUT is not set
# BR2_PACKAGE_LIBSOCKETCAN is not set
# BR2_PACKAGE_LIBSOUP is not set
# BR2_PACKAGE_LIBSOUP3 is not set
# BR2_PACKAGE_LIBSRTP is not set
# BR2_PACKAGE_LIBSTROPHE is not set
# BR2_PACKAGE_LIBTEAM is not set
# BR2_PACKAGE_LIBTELNET is not set
# BR2_PACKAGE_LIBTIRPC is not set
#
# libtorrent needs a toolchain w/ C++, threads
#
#
# libtorrent-rasterbar needs a toolchain w/ C++, threads, wchar, gcc >= 4.9
#
# BR2_PACKAGE_LIBUEV is not set
# BR2_PACKAGE_LIBUHTTPD is not set
# BR2_PACKAGE_LIBUPNP is not set
#
# libupnpp needs a toolchain w/ C++, threads, gcc >= 4.9
#
# BR2_PACKAGE_LIBURIPARSER is not set
#
# libutp support needs a toolchain with C++
#
# BR2_PACKAGE_LIBUWSC is not set
# BR2_PACKAGE_LIBVNCSERVER is not set
# BR2_PACKAGE_LIBWEBSOCK is not set
# BR2_PACKAGE_LIBWEBSOCKETS is not set
# BR2_PACKAGE_LIBYANG is not set
BR2_PACKAGE_LIBZENOH_C_ARCH_SUPPORTS=y
# BR2_PACKAGE_LIBZENOH_C is not set
# BR2_PACKAGE_LIBZENOH_PICO is not set
# BR2_PACKAGE_LKSCTP_TOOLS is not set
# BR2_PACKAGE_MBUFFER is not set
# BR2_PACKAGE_MDNSD is not set
# BR2_PACKAGE_MONGOOSE is not set
# BR2_PACKAGE_NANOMSG is not set
# BR2_PACKAGE_NEON is not set
#
# netopeer2 needs a toolchain w/ gcc >= 4.8, C++, threads, dynamic library
#
# BR2_PACKAGE_NGHTTP2 is not set
#
# norm needs a toolchain w/ C++, threads, dynamic library
#
# BR2_PACKAGE_NSS_MYHOSTNAME is not set
# BR2_PACKAGE_NSS_PAM_LDAPD is not set
#
# oatpp needs a toolchain w/ C++, threads
#
#
# omniORB needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_OPEN_ISNS is not set
# BR2_PACKAGE_OPEN62541 is not set
# BR2_PACKAGE_OPENLDAP is not set
#
# openmpi needs a toolchain w/ dynamic library, NPTL, wchar, C++
#
# BR2_PACKAGE_OPENPGM is not set
#
# openzwave needs a toolchain w/ C++, dynamic library, NPTL, wchar
#
#
# ortp needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_PAHO_MQTT_C is not set
#
# paho-mqtt-cpp needs a toolchain w/ threads, C++
#
#
# pistache needs a toolchain w/ C++, gcc >= 7, NPTL, wchar
#
# BR2_PACKAGE_QDECODER is not set
#
# qpid-proton needs a toolchain w/ C++, dynamic library, threads
#
# BR2_PACKAGE_RABBITMQ_C is not set
#
# resiprocate needs a toolchain w/ C++, threads, wchar
#
#
# restclient-cpp needs a toolchain w/ C++, gcc >= 4.8
#
# BR2_PACKAGE_RTMPDUMP is not set
# BR2_PACKAGE_SIPROXD is not set
# BR2_PACKAGE_SLIRP is not set
# BR2_PACKAGE_SLIRP4NETNS is not set
#
# snmp++ needs a toolchain w/ threads, C++, dynamic library
#
# BR2_PACKAGE_SOFIA_SIP is not set
# BR2_PACKAGE_SSCEP is not set
#
# sysrepo needs a toolchain w/ C++, NPTL, dynamic library, gcc >= 4.8
#
#
# thrift needs a toolchain w/ C++, wchar, threads
#
# BR2_PACKAGE_USBREDIR is not set
#
# wampcc needs a toolchain w/ C++, NPTL, dynamic library, gcc >= 4.9
#
#
# websocketpp needs a toolchain w/ C++ and gcc >= 4.8
#
#
# zeromq needs a toolchain w/ C++, threads
#
#
# zmqpp needs a toolchain w/ C++, threads, gcc >= 4.7
#
#
# zyre needs a toolchain w/ C++, threads
#
#
# Other
#
#
# ACE needs a glibc toolchain, dynamic library, C++, gcc >= 4.9
#
# BR2_PACKAGE_APR is not set
# BR2_PACKAGE_APR_UTIL is not set
#
# armadillo needs a toolchain w/ C++
#
#
# atf needs a toolchain w/ C++
#
# BR2_PACKAGE_AVRO_C is not set
# BR2_PACKAGE_BASU is not set
#
# bctoolbox needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_BDWGC is not set
#
# belr needs a toolchain w/ threads, C++
#
#
# boost needs a toolchain w/ C++, threads, wchar
#
#
# c-capnproto needs host and target gcc >= 5 w/ C++14, threads, atomic, ucontext and not gcc bug 64735
#
#
# capnproto needs host and target gcc >= 5 w/ C++14, threads, atomic, ucontext and not gcc bug 64735
#
#
# catch2 needs a toolchain w/ C++, wchar, threads, gcc >= 5
#
#
# cctz needs a toolchain w/ C++, threads, gcc >= 4.8
#
#
# cereal needs a toolchain w/ C++, gcc >= 4.7, threads, wchar
#
#
# clang needs a toolchain w/ wchar, threads, C++, gcc >= 7, dynamic library, host gcc >= 7
#
# BR2_PACKAGE_CMOCKA is not set
#
# cppcms needs a toolchain w/ C++, NPTL, wchar, dynamic library
#
# BR2_PACKAGE_CRACKLIB is not set
#
# dawgdic needs a toolchain w/ C++, gcc >= 4.6
#
# BR2_PACKAGE_DING_LIBS is not set
# BR2_PACKAGE_DOTCONF is not set
#
# double-conversion needs a toolchain w/ C++
#
#
# eigen needs a toolchain w/ C++
#
# BR2_PACKAGE_ELFUTILS is not set
# BR2_PACKAGE_ELL is not set
# BR2_PACKAGE_FFTW is not set
#
# flann needs a toolchain w/ C++, dynamic library, gcc >= 4.7
#
#
# flatbuffers needs a toolchain w/ C++, gcc >= 4.7
#
# BR2_PACKAGE_FLATCC is not set
# BR2_PACKAGE_FXDIV is not set
# BR2_PACKAGE_GCONF is not set
#
# gdal needs a toolchain w/ C++, dynamic library, gcc >= 4.7, NPTL, wchar
#
#
# gflags needs a toolchain w/ C++
#
#
# gli needs a toolchain w/ C++
#
#
# glibmm needs a toolchain w/ C++, wchar, threads, gcc >= 7
#
#
# glibmm (2.66.x) needs a toolchain w/ C++, wchar, threads, gcc >= 4.9
#
#
# glm needs a toolchain w/ C++
#
# BR2_PACKAGE_GMP is not set
BR2_PACKAGE_GOBJECT_INTROSPECTION_ARCH_SUPPORTS=y
#
# gobject-introspection needs python3
#
# BR2_PACKAGE_GSL is not set
#
# gtest needs a toolchain w/ C++, wchar, threads, gcc >= 5
#
# BR2_PACKAGE_GUMBO_PARSER is not set
#
# highway needs a toolchain w/ C++, gcc >= 7
#
BR2_PACKAGE_JEMALLOC_ARCH_SUPPORTS=y
# BR2_PACKAGE_JEMALLOC is not set
BR2_PACKAGE_LAPACK_ARCH_SUPPORTS=y
#
# lapack/blas needs a toolchain w/ fortran
#
BR2_PACKAGE_LIBABSEIL_CPP_ARCH_SUPPORTS=y
#
# libabseil-cpp needs a toolchain w/ gcc >= 8, C++, threads, dynamic library
#
# BR2_PACKAGE_LIBARGTABLE2 is not set
BR2_PACKAGE_LIBATOMIC_OPS_ARCH_SUPPORTS=y
# BR2_PACKAGE_LIBATOMIC_OPS is not set
# BR2_PACKAGE_LIBAVL is not set
# BR2_PACKAGE_LIBB64 is not set
# BR2_PACKAGE_LIBBACKTRACE is not set
BR2_PACKAGE_LIBBSD_ARCH_SUPPORTS=y
# BR2_PACKAGE_LIBBSD is not set
# BR2_PACKAGE_LIBBYTESIZE is not set
# BR2_PACKAGE_LIBCAP is not set
# BR2_PACKAGE_LIBCAP_NG is not set
#
# libcgroup needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LIBCLC is not set
# BR2_PACKAGE_LIBCORRECT is not set
#
# libcrossguid needs a toolchain w/ C++, gcc >= 4.7
#
# BR2_PACKAGE_LIBCSV is not set
# BR2_PACKAGE_LIBDAEMON is not set
# BR2_PACKAGE_LIBDEX is not set
# BR2_PACKAGE_LIBDILL is not set
BR2_PACKAGE_LIBEASTL_ARCH_SUPPORTS=y
#
# libeastl needs a toolchain w/ C++, threads, gcc >= 4.9
#
# BR2_PACKAGE_LIBEE is not set
# BR2_PACKAGE_LIBEV is not set
# BR2_PACKAGE_LIBEVDEV is not set
# BR2_PACKAGE_LIBEVENT is not set
#
# libexecinfo needs a musl or uclibc toolchain w/ dynamic library
#
# BR2_PACKAGE_LIBFFI is not set
#
# libfutils needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LIBGEE is not set
#
# libgeos needs a toolchain w/ C++, wchar, gcc >= 4.9, threads
#
# BR2_PACKAGE_LIBGLIB2 is not set
# BR2_PACKAGE_LIBGLOB is not set
#
# libical needs a toolchain w/ C++, dynamic library, wchar
#
# BR2_PACKAGE_LIBITE is not set
#
# libks needs a toolchain w/ C++, NPTL, dynamic library
#
#
# liblinear needs a toolchain w/ C++
#
#
# libloki needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LIBNPTH is not set
BR2_PACKAGE_LIBNSPR_ARCH_SUPPORT=y
# BR2_PACKAGE_LIBNSPR is not set
#
# libosmium needs a toolchain w/ C++, wchar, threads, gcc >= 4.7
#
#
# libpeas needs python3
#
# BR2_PACKAGE_LIBPFM4 is not set
#
# libplist needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_LIBPTHREAD_STUBS is not set
# BR2_PACKAGE_LIBPTHSEM is not set
# BR2_PACKAGE_LIBPWQUALITY is not set
# BR2_PACKAGE_LIBQB is not set
BR2_PACKAGE_LIBSECCOMP_ARCH_SUPPORTS=y
# BR2_PACKAGE_LIBSECCOMP is not set
#
# libshdata needs a toolchain w/ C++, threads
#
#
# libsigc++ needs a toolchain w/ C++, gcc >= 7
#
#
# libsigc++ (2.x.x) needs a toolchain w/ C++, gcc >= 4.9
#
BR2_PACKAGE_LIBSIGSEGV_ARCH_SUPPORTS=y
# BR2_PACKAGE_LIBSIGSEGV is not set
# BR2_PACKAGE_LIBSOLV is not set
#
# libspatialindex needs a toolchain w/ C++, gcc >= 4.7
#
# BR2_PACKAGE_LIBTALLOC is not set
# BR2_PACKAGE_LIBTASN1 is not set
# BR2_PACKAGE_LIBTOMMATH is not set
# BR2_PACKAGE_LIBTPL is not set
# BR2_PACKAGE_LIBUBOX is not set
# BR2_PACKAGE_LIBUCI is not set
BR2_PACKAGE_LIBUNWIND_ARCH_SUPPORTS=y
# BR2_PACKAGE_LIBUNWIND is not set
BR2_PACKAGE_LIBURCU_ARCH_SUPPORTS=y
#
# liburcu needs a toolchain w/ threads, C++
#
# BR2_PACKAGE_LIBURING is not set
# BR2_PACKAGE_LIBUTEMPTER is not set
# BR2_PACKAGE_LIBUV is not set
# BR2_PACKAGE_LINUX_PAM is not set
# BR2_PACKAGE_LIQUID_DSP is not set
BR2_PACKAGE_LLVM_ARCH_SUPPORTS=y
BR2_PACKAGE_LLVM_TARGET_ARCH="AArch64"
#
# llvm needs a toolchain w/ wchar, threads, C++, gcc >= 7, dynamic library, host gcc >= 7
#
#
# lttng-libust needs a toolchain w/ dynamic library, wchar, threads, C++
#
# BR2_PACKAGE_MATIO is not set
# BR2_PACKAGE_MPC is not set
# BR2_PACKAGE_MPDECIMAL is not set
# BR2_PACKAGE_MPFR is not set
# BR2_PACKAGE_MPIR is not set
#
# msgpack needs a toolchain w/ C++
#
# BR2_PACKAGE_NEON_2_SSE is not set
BR2_PACKAGE_OPENBLAS_DEFAULT_TARGET="ARMV8"
BR2_PACKAGE_OPENBLAS_ARCH_SUPPORTS=y
# BR2_PACKAGE_OPENBLAS is not set
# BR2_PACKAGE_ORC is not set
# BR2_PACKAGE_P11_KIT is not set
BR2_PACKAGE_POCO_ARCH_SUPPORTS=y
#
# poco needs a toolchain w/ wchar, NPTL, C++, dynamic library, gcc >= 8
#
BR2_PACKAGE_HOST_PROTOBUF_ARCH_SUPPORTS=y
BR2_PACKAGE_PROTOBUF_ARCH_SUPPORTS=y
#
# protobuf needs a toolchain w/ C++, threads, dynamic library, gcc >= 4.8
#
#
# protobuf-c needs a toolchain w/ C++, threads, host gcc >= 7
#
#
# protozero needs a toolchain w/ C++, gcc >= 4.7
#
#
# qhull needs a toolchain w/ C++, gcc >= 4.4
#
# BR2_PACKAGE_QLIBC is not set
# BR2_PACKAGE_REPROC is not set
#
# riemann-c-client needs a toolchain w/ C++, threads, host gcc >= 7
#
#
# shapelib needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_SKALIBS is not set
# BR2_PACKAGE_SPHINXBASE is not set
#
# tbb needs a glibc or musl toolchain w/ dynamic library, threads, C++
#
# BR2_PACKAGE_TINYCBOR is not set
#
# tl-expected needs a toolchain w/ C++, gcc >= 4.8
#
# BR2_PACKAGE_TLLIST is not set
#
# uvw needs a toolchain w/ NPTL, dynamic library, C++, gcc >= 7
#
#
# volk needs a toolchain w/ C++, NPTL, wchar, dynamic library
#
#
# xapian needs a toolchain w/ C++
#
#
# Security
#
# BR2_PACKAGE_LIBAPPARMOR is not set
# BR2_PACKAGE_LIBSELINUX is not set
# BR2_PACKAGE_LIBSEMANAGE is not set
# BR2_PACKAGE_LIBSEPOL is not set
# BR2_PACKAGE_SAFECLIB is not set
#
# softhsm2 needs a toolchain w/ C++, threads, gcc >= 4.8 and dynamic library support
#
#
# Text and terminal handling
#
# BR2_PACKAGE_AUGEAS is not set
#
# cli11 needs a toolchain w/ C++, gcc >= 4.8
#
#
# docopt-cpp needs a toolchain w/ C++, gcc >= 4.7
#
#
# enchant needs a toolchain w/ C++, threads, wchar
#
# BR2_PACKAGE_FCFT is not set
#
# fmt needs a toolchain w/ C++, wchar
#
# BR2_PACKAGE_FSTRCMP is not set
#
# icu needs a toolchain w/ C++, wchar, threads, gcc >= 4.9, host gcc >= 4.9
#
# BR2_PACKAGE_INIH is not set
# BR2_PACKAGE_LIBCLI is not set
# BR2_PACKAGE_LIBEDIT is not set
# BR2_PACKAGE_LIBENCA is not set
# BR2_PACKAGE_LIBESTR is not set
# BR2_PACKAGE_LIBFRIBIDI is not set
# BR2_PACKAGE_LIBUNIBREAK is not set
# BR2_PACKAGE_LIBUNISTRING is not set
# BR2_PACKAGE_LINENOISE is not set
# BR2_PACKAGE_NCURSES is not set
# BR2_PACKAGE_NEWT is not set
# BR2_PACKAGE_ONIGURUMA is not set
# BR2_PACKAGE_PCRE is not set
# BR2_PACKAGE_PCRE2 is not set
# BR2_PACKAGE_POPT is not set
#
# re2 needs a toolchain w/ C++, threads, dynamic library, gcc >= 8
#
# BR2_PACKAGE_READLINE is not set
# BR2_PACKAGE_SLANG is not set
#
# tclap needs a toolchain w/ C++
#
#
# termcolor needs a toolchain w/ C++, gcc >= 4.8
#
# BR2_PACKAGE_UTF8PROC is not set
#
# Mail
#
# BR2_PACKAGE_DOVECOT is not set
# BR2_PACKAGE_EXIM is not set
# BR2_PACKAGE_FETCHMAIL is not set
# BR2_PACKAGE_HEIRLOOM_MAILX is not set
# BR2_PACKAGE_LIBESMTP is not set
# BR2_PACKAGE_MSMTP is not set
# BR2_PACKAGE_MUTT is not set
#
# Miscellaneous
#
# BR2_PACKAGE_AESPIPE is not set
# BR2_PACKAGE_BC is not set
BR2_PACKAGE_BITCOIN_ARCH_SUPPORTS=y
#
# bitcoin needs a toolchain w/ C++, threads, wchar, gcc >= 9
#
#
# clamav needs a toolchain w/ C++, dynamic library, threads, wchar
#
# BR2_PACKAGE_COLLECTD is not set
# BR2_PACKAGE_COLLECTL is not set
#
# domoticz needs lua 5.3 and a toolchain w/ C++, gcc >= 6, NPTL, wchar, dynamic library
#
# BR2_PACKAGE_EMPTY is not set
# BR2_PACKAGE_FFT_EVAL is not set
# BR2_PACKAGE_GITLAB_RUNNER is not set
#
# gnuradio needs a toolchain w/ C++, NPTL, wchar, dynamic library, gcc >= 8
#
# BR2_PACKAGE_GOOGLEFONTDIRECTORY is not set
#
# gqrx needs a toolchain w/ C++, threads, wchar, dynamic library, gcc >= 8
#
#
# gqrx needs qt5
#
# BR2_PACKAGE_GSETTINGS_DESKTOP_SCHEMAS is not set
# BR2_PACKAGE_HAVEGED is not set
# BR2_PACKAGE_LINUX_SYSCALL_SUPPORT is not set
# BR2_PACKAGE_MOBILE_BROADBAND_PROVIDER_INFO is not set
# BR2_PACKAGE_NETDATA is not set
#
# proj needs a toolchain w/ C++, gcc >= 4.7, NPTL, wchar
#
BR2_PACKAGE_QEMU_ARCH_SUPPORTS_TARGET=y
# BR2_PACKAGE_QEMU is not set
#
# qpdf needs a toolchain w/ C++, gcc >= 5
#
# BR2_PACKAGE_RTL_433 is not set
# BR2_PACKAGE_SHARED_MIME_INFO is not set
#
# sunwait needs a toolchain w/ C++
#
#
# taskd needs a toolchain w/ C++, wchar, dynamic library
#
BR2_PACKAGE_XMRIG_ARCH_SUPPORTS=y
#
# xmrig needs a glibc or musl toolchain w/ NPTL, dynamic library, C++, gcc >= 4.9
#
# BR2_PACKAGE_XUTIL_UTIL_MACROS is not set
BR2_PACKAGE_Z3_ARCH_SUPPORTS=y
#
# Networking applications
#
#
# aircrack-ng needs a toolchain w/ dynamic library, threads, C++
#
# BR2_PACKAGE_ALFRED is not set
# BR2_PACKAGE_AOETOOLS is not set
# BR2_PACKAGE_APACHE is not set
# BR2_PACKAGE_ARGUS is not set
# BR2_PACKAGE_ARP_SCAN is not set
# BR2_PACKAGE_ARPTABLES is not set
#
# asterisk needs a glibc or uClibc toolchain w/ C++, dynamic library, threads, wchar
#
# BR2_PACKAGE_ATFTP is not set
# BR2_PACKAGE_AVAHI is not set
# BR2_PACKAGE_AXEL is not set
# BR2_PACKAGE_BABELD is not set
# BR2_PACKAGE_BANDWIDTHD is not set
# BR2_PACKAGE_BATCTL is not set
#
# bcusdk needs a toolchain w/ C++
#
# BR2_PACKAGE_BIND is not set
# BR2_PACKAGE_BIRD is not set
# BR2_PACKAGE_BLUEZ5_UTILS is not set
# BR2_PACKAGE_BMON is not set
# BR2_PACKAGE_BMX7 is not set
#
# boinc needs a toolchain w/ dynamic library, C++, threads, gcc >= 4.8
#
# BR2_PACKAGE_BRCM_PATCHRAM_PLUS is not set
# BR2_PACKAGE_BRIDGE_UTILS is not set
# BR2_PACKAGE_BWM_NG is not set
# BR2_PACKAGE_C_ICAP is not set
# BR2_PACKAGE_CAN_UTILS is not set
#
# cannelloni needs a toolchain w/ C++, threads, dynamic library, gcc >= 4.8
#
# BR2_PACKAGE_CASYNC is not set
# BR2_PACKAGE_CFM is not set
# BR2_PACKAGE_CHRONY is not set
# BR2_PACKAGE_CIVETWEB is not set
# BR2_PACKAGE_CLOUDFLARED is not set
# BR2_PACKAGE_CONNMAN is not set
#
# connman-gtk needs libgtk3 and a glibc or uClibc toolchain w/ wchar, threads, resolver, dynamic library
#
# BR2_PACKAGE_CONNTRACK_TOOLS is not set
# BR2_PACKAGE_CORKSCREW is not set
# BR2_PACKAGE_CRDA is not set
#
# ctorrent needs a toolchain w/ C++
#
#
# cups needs a toolchain w/ C++, threads
#
#
# cups-filters needs a toolchain w/ wchar, C++, threads and dynamic library, gcc >= 5
#
# BR2_PACKAGE_DANTE is not set
# BR2_PACKAGE_DARKHTTPD is not set
# BR2_PACKAGE_DEHYDRATED is not set
# BR2_PACKAGE_DHCPCD is not set
# BR2_PACKAGE_DHCPDUMP is not set
# BR2_PACKAGE_DNSMASQ is not set
# BR2_PACKAGE_DRBD_UTILS is not set
# BR2_PACKAGE_DROPBEAR is not set
# BR2_PACKAGE_EASYFRAMES is not set
# BR2_PACKAGE_EBTABLES is not set
#
# ejabberd needs erlang, toolchain w/ C++
#
# BR2_PACKAGE_ETHTOOL is not set
# BR2_PACKAGE_FAIFA is not set
# BR2_PACKAGE_FASTD is not set
# BR2_PACKAGE_FCGIWRAP is not set
# BR2_PACKAGE_FIREWALLD is not set
# BR2_PACKAGE_FLANNEL is not set
#
# fmc needs a toolchain w/ C++
#
# BR2_PACKAGE_FPING is not set
# BR2_PACKAGE_FREERADIUS_SERVER is not set
#
# freeswitch needs a toolchain w/ C++, dynamic library, threads, wchar
#
# BR2_PACKAGE_FRR is not set
#
# gerbera needs a toolchain w/ C++, dynamic library, threads, wchar, gcc >= 8
#
# BR2_PACKAGE_GESFTPSERVER is not set
#
# gloox needs a toolchain w/ C++
#
# BR2_PACKAGE_GLORYTUN is not set
#
# gupnp-tools needs libgtk3
#
#
# hans needs a toolchain w/ C++
#
BR2_PACKAGE_HAPROXY_ARCH_SUPPORTS=y
# BR2_PACKAGE_HAPROXY is not set
# BR2_PACKAGE_HIAWATHA is not set
# BR2_PACKAGE_HOSTAPD is not set
# BR2_PACKAGE_HTPDATE is not set
# BR2_PACKAGE_HTTPING is not set
#
# i2pd needs a toolchain w/ C++, NPTL, wchar
#
#
# ibrdtn-tools needs a toolchain w/ C++, threads
#
#
# ibrdtnd needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_IFMETRIC is not set
# BR2_PACKAGE_IFTOP is not set
BR2_PACKAGE_IFUPDOWN_SCRIPTS=y
# BR2_PACKAGE_IGD2_FOR_LINUX is not set
# BR2_PACKAGE_IGH_ETHERCAT is not set
# BR2_PACKAGE_IGMPPROXY is not set
# BR2_PACKAGE_INADYN is not set
# BR2_PACKAGE_IODINE is not set
#
# iperf needs a toolchain w/ C++
#
# BR2_PACKAGE_IPERF3 is not set
# BR2_PACKAGE_IPROUTE2 is not set
# BR2_PACKAGE_IPSET is not set
# BR2_PACKAGE_IPTABLES is not set
# BR2_PACKAGE_IPTRAF_NG is not set
# BR2_PACKAGE_IPUTILS is not set
# BR2_PACKAGE_IRSSI is not set
# BR2_PACKAGE_IW is not set
# BR2_PACKAGE_IWD is not set
# BR2_PACKAGE_JANUS_GATEWAY is not set
# BR2_PACKAGE_KEEPALIVED is not set
#
# kismet needs a toolchain w/ threads, C++, gcc >= 5, host gcc >= 7
#
# BR2_PACKAGE_KNOCK is not set
# BR2_PACKAGE_KSMBD_TOOLS is not set
# BR2_PACKAGE_LEAFNODE2 is not set
# BR2_PACKAGE_LFT is not set
#
# lftp requires a toolchain w/ C++, wchar
#
# BR2_PACKAGE_LIGHTTPD is not set
#
# linknx needs a toolchain w/ C++
#
# BR2_PACKAGE_LINKS is not set
#
# linphone needs a toolchain w/ threads, C++, dynamic library, wchar, gcc >= 5
#
# BR2_PACKAGE_LINUX_ZIGBEE is not set
# BR2_PACKAGE_LINUXPTP is not set
# BR2_PACKAGE_LLDPD is not set
# BR2_PACKAGE_LRZSZ is not set
# BR2_PACKAGE_LYNX is not set
# BR2_PACKAGE_MACCHANGER is not set
# BR2_PACKAGE_MEMCACHED is not set
# BR2_PACKAGE_MII_DIAG is not set
# BR2_PACKAGE_MINI_SNMPD is not set
# BR2_PACKAGE_MINIDLNA is not set
# BR2_PACKAGE_MINISSDPD is not set
# BR2_PACKAGE_MJPG_STREAMER is not set
# BR2_PACKAGE_MODEM_MANAGER is not set
BR2_PACKAGE_MONGREL2_LIBC_SUPPORTS=y
#
# mongrel2 needs a uClibc or glibc toolchain w/ C++, threads, dynamic library
#
#
# mosh needs a toolchain w/ C++, threads, dynamic library, wchar, gcc >= 4.8
#
# BR2_PACKAGE_MOSQUITTO is not set
# BR2_PACKAGE_MROUTED is not set
# BR2_PACKAGE_MRP is not set
# BR2_PACKAGE_MSTPD is not set
# BR2_PACKAGE_MTR is not set
# BR2_PACKAGE_NBD is not set
# BR2_PACKAGE_NCFTP is not set
# BR2_PACKAGE_NDISC6 is not set
# BR2_PACKAGE_NETATALK is not set
# BR2_PACKAGE_NETCALC is not set
#
# nethogs needs a toolchain w/ C++
#
# BR2_PACKAGE_NETPLUG is not set
# BR2_PACKAGE_NETSNMP is not set
# BR2_PACKAGE_NETSTAT_NAT is not set
#
# NetworkManager needs udev /dev management and a glibc or musl toolchain w/ headers >= 4.6, dynamic library, wchar, threads, gcc >= 4.9
#
# BR2_PACKAGE_NFACCT is not set
# BR2_PACKAGE_NFTABLES is not set
# BR2_PACKAGE_NGINX is not set
# BR2_PACKAGE_NGIRCD is not set
# BR2_PACKAGE_NGREP is not set
#
# nload needs a toolchain w/ C++
#
#
# nmap-nmap needs a toolchain w/ C++, threads
#
# BR2_PACKAGE_NOIP is not set
# BR2_PACKAGE_NTP is not set
# BR2_PACKAGE_NTPSEC is not set
# BR2_PACKAGE_NUTTCP is not set
# BR2_PACKAGE_ODHCP6C is not set
# BR2_PACKAGE_ODHCPLOC is not set
# BR2_PACKAGE_OLSR is not set
# BR2_PACKAGE_OPEN_ISCSI is not set
# BR2_PACKAGE_OPEN_LLDP is not set
# BR2_PACKAGE_OPEN_PLC_UTILS is not set
# BR2_PACKAGE_OPENCONNECT is not set
# BR2_PACKAGE_OPENNTPD is not set
# BR2_PACKAGE_OPENOBEX is not set
# BR2_PACKAGE_OPENRESOLV is not set
# BR2_PACKAGE_OPENSSH is not set
# BR2_PACKAGE_OPENSWAN is not set
# BR2_PACKAGE_OPENVPN is not set
# BR2_PACKAGE_P910ND is not set
# BR2_PACKAGE_PARPROUTED is not set
# BR2_PACKAGE_PHIDGETWEBSERVICE is not set
# BR2_PACKAGE_PHYTOOL is not set
# BR2_PACKAGE_PIMD is not set
# BR2_PACKAGE_PIXIEWPS is not set
# BR2_PACKAGE_POUND is not set
# BR2_PACKAGE_PPPD is not set
# BR2_PACKAGE_PPTP_LINUX is not set
# BR2_PACKAGE_PRIVOXY is not set
# BR2_PACKAGE_PROFTPD is not set
#
# prosody needs the lua interpreter, dynamic library
#
# BR2_PACKAGE_PROXYCHAINS_NG is not set
# BR2_PACKAGE_PTPD is not set
# BR2_PACKAGE_PTPD2 is not set
# BR2_PACKAGE_PURE_FTPD is not set
# BR2_PACKAGE_PUTTY is not set
# BR2_PACKAGE_QUAGGA is not set
# BR2_PACKAGE_RADVD is not set
# BR2_PACKAGE_REAVER is not set
# BR2_PACKAGE_REDIR is not set
# BR2_PACKAGE_RP_PPPOE is not set
# BR2_PACKAGE_RPCBIND is not set
# BR2_PACKAGE_RSH_REDONE is not set
# BR2_PACKAGE_RSYNC is not set
#
# rtorrent needs a toolchain w/ C++, threads, wchar, gcc >= 4.9
#
# BR2_PACKAGE_RTPTOOLS is not set
# BR2_PACKAGE_S6_DNS is not set
# BR2_PACKAGE_S6_NETWORKING is not set
# BR2_PACKAGE_SAMBA4 is not set
#
# sconeserver needs a toolchain with dynamic library, C++, NPTL
#
# BR2_PACKAGE_SER2NET is not set
# BR2_PACKAGE_SHADOWSOCKS_LIBEV is not set
#
# shairport-sync needs a toolchain w/ C++, NPTL
#
# BR2_PACKAGE_SHELLINABOX is not set
# BR2_PACKAGE_SMCROUTE is not set
# BR2_PACKAGE_SNGREP is not set
# BR2_PACKAGE_SNORT is not set
#
# snort3 needs a toolchain w/ C++, wchar, threads, dynamic library, gcc >= 4.9
#
# BR2_PACKAGE_SOCAT is not set
# BR2_PACKAGE_SOCKETCAND is not set
# BR2_PACKAGE_SOFTETHER is not set
# BR2_PACKAGE_SPAWN_FCGI is not set
# BR2_PACKAGE_SPICE_PROTOCOL is not set
#
# squid needs a toolchain w/ C++, threads, gcc >= 8, host gcc >= 8
#
# BR2_PACKAGE_SSDP_RESPONDER is not set
# BR2_PACKAGE_SSHGUARD is not set
# BR2_PACKAGE_SSHPASS is not set
# BR2_PACKAGE_SSLH is not set
# BR2_PACKAGE_STRONGSWAN is not set
# BR2_PACKAGE_STUNNEL is not set
# BR2_PACKAGE_SURICATA is not set
# BR2_PACKAGE_TCPDUMP is not set
# BR2_PACKAGE_TCPING is not set
# BR2_PACKAGE_TCPREPLAY is not set
# BR2_PACKAGE_THTTPD is not set
# BR2_PACKAGE_TINC is not set
# BR2_PACKAGE_TINYPROXY is not set
# BR2_PACKAGE_TINYSSH is not set
# BR2_PACKAGE_TIPIDEE is not set
# BR2_PACKAGE_TOR is not set
# BR2_PACKAGE_TRACEROUTE is not set
#
# transmission needs a toolchain w/ dynamic library, threads, C++, gcc >= 7
#
# BR2_PACKAGE_TUNCTL is not set
# BR2_PACKAGE_TVHEADEND is not set
# BR2_PACKAGE_UACME is not set
# BR2_PACKAGE_UDPCAST is not set
# BR2_PACKAGE_UFTP is not set
# BR2_PACKAGE_UHTTPD is not set
# BR2_PACKAGE_ULOGD is not set
# BR2_PACKAGE_UNBOUND is not set
# BR2_PACKAGE_UQMI is not set
# BR2_PACKAGE_UREDIR is not set
# BR2_PACKAGE_USHARE is not set
# BR2_PACKAGE_USSP_PUSH is not set
# BR2_PACKAGE_USTREAMER is not set
# BR2_PACKAGE_VDE2 is not set
#
# vdr needs a toolchain w/ C++, dynamic library, NPTL, wchar, headers >= 3.9
#
# BR2_PACKAGE_VNSTAT is not set
# BR2_PACKAGE_VPNC is not set
# BR2_PACKAGE_VSFTPD is not set
# BR2_PACKAGE_VTUN is not set
# BR2_PACKAGE_WAVEMON is not set
# BR2_PACKAGE_WIREGUARD_TOOLS is not set
# BR2_PACKAGE_WIRELESS_REGDB is not set
# BR2_PACKAGE_WIRELESS_TOOLS is not set
#
# wireshark needs a toolchain w/ wchar, threads, dynamic library, C++
#
# BR2_PACKAGE_WPA_SUPPLICANT is not set
# BR2_PACKAGE_WPAN_TOOLS is not set
# BR2_PACKAGE_XINETD is not set
# BR2_PACKAGE_XL2TP is not set
# BR2_PACKAGE_XTABLES_ADDONS is not set
# BR2_PACKAGE_ZABBIX is not set
#
# zeek needs a toolchain w/ C++, wchar, threads, dynamic library, gcc >= 7, host gcc >= 7
#
#
# znc needs a toolchain w/ C++, dynamic library, gcc >= 8, threads
#
#
# Package managers
#
#
# -------------------------------------------------------
#
#
# Please note:
#
#
# - Buildroot does *not* generate binary packages,
#
#
# - Buildroot does *not* install any package database.
#
#
# *
#
#
# It is up to you to provide those by yourself if you
#
#
# want to use any of those package managers.
#
#
# *
#
#
# See the manual:
#
#
# http://buildroot.org/manual.html#faq-no-binary-packages
#
#
# -------------------------------------------------------
#
# BR2_PACKAGE_OPKG is not set
# BR2_PACKAGE_OPKG_UTILS is not set
#
# Real-Time
#
# BR2_PACKAGE_XENOMAI is not set
#
# Security
#
#
# apparmor needs a toolchain w/ headers >= 3.16, threads, C++
#
# BR2_PACKAGE_CHECKPOLICY is not set
# BR2_PACKAGE_IMA_EVM_UTILS is not set
# BR2_PACKAGE_OPTEE_CLIENT is not set
# BR2_PACKAGE_PAXTEST is not set
# BR2_PACKAGE_POLICYCOREUTILS is not set
# BR2_PACKAGE_REFPOLICY is not set
# BR2_PACKAGE_RESTORECOND is not set
# BR2_PACKAGE_SELINUX_PYTHON is not set
# BR2_PACKAGE_SEMODULE_UTILS is not set
#
# setools needs python3
#
BR2_PACKAGE_URANDOM_SCRIPTS=y
#
# Shell and utilities
#
#
# Shells
#
# BR2_PACKAGE_MKSH is not set
# BR2_PACKAGE_NUSHELL is not set
# BR2_PACKAGE_ZSH is not set
#
# Utilities
#
# BR2_PACKAGE_APG is not set
# BR2_PACKAGE_AT is not set
# BR2_PACKAGE_CATATONIT is not set
# BR2_PACKAGE_CCRYPT is not set
# BR2_PACKAGE_DIALOG is not set
# BR2_PACKAGE_DTACH is not set
# BR2_PACKAGE_EASY_RSA is not set
# BR2_PACKAGE_EZA is not set
# BR2_PACKAGE_FILE is not set
# BR2_PACKAGE_GNUPG is not set
BR2_PACKAGE_GNUPG2_DEPENDS=y
# BR2_PACKAGE_GNUPG2 is not set
# BR2_PACKAGE_INOTIFY_TOOLS is not set
# BR2_PACKAGE_LOCKFILE_PROGS is not set
# BR2_PACKAGE_LOGROTATE is not set
# BR2_PACKAGE_LOGSURFER is not set
# BR2_PACKAGE_MINISIGN is not set
# BR2_PACKAGE_PDMENU is not set
# BR2_PACKAGE_PINENTRY is not set
# BR2_PACKAGE_QPRINT is not set
# BR2_PACKAGE_RANGER is not set
# BR2_PACKAGE_RLWRAP is not set
# BR2_PACKAGE_RTTY is not set
# BR2_PACKAGE_SCREEN is not set
# BR2_PACKAGE_SEXPECT is not set
# BR2_PACKAGE_SUDO is not set
# BR2_PACKAGE_TINI is not set
# BR2_PACKAGE_TMUX is not set
# BR2_PACKAGE_TTYD is not set
# BR2_PACKAGE_WTFUTIL is not set
# BR2_PACKAGE_XMLSTARLET is not set
# BR2_PACKAGE_XXHASH is not set
# BR2_PACKAGE_YTREE is not set
# BR2_PACKAGE_ZOXIDE is not set
#
# System tools
#
# BR2_PACKAGE_ACL is not set
# BR2_PACKAGE_ANDROID_TOOLS is not set
# BR2_PACKAGE_ATOP is not set
# BR2_PACKAGE_ATTR is not set
BR2_PACKAGE_AUDIT_ARCH_SUPPORTS=y
# BR2_PACKAGE_AUDIT is not set
# BR2_PACKAGE_BALENA_ENGINE is not set
# BR2_PACKAGE_BUBBLEWRAP is not set
# BR2_PACKAGE_CGROUPFS_MOUNT is not set
#
# circus needs Python 3 and a toolchain w/ C++, threads
#
# BR2_PACKAGE_CONMON is not set
# BR2_PACKAGE_CONTAINERD is not set
# BR2_PACKAGE_CPULIMIT is not set
# BR2_PACKAGE_CPULOAD is not set
BR2_PACKAGE_CRIU_ARCH_SUPPORTS=y
#
# criu needs a glibc or musl toolchain w/ threads, host gcc >= 7, gcc >= 8, headers >= 4.18, C++, dynamic library, wchar
#
# BR2_PACKAGE_CRUN is not set
# BR2_PACKAGE_DAEMON is not set
# BR2_PACKAGE_DC3DD is not set
#
# ddrescue needs a toolchain w/ C++
#
# BR2_PACKAGE_DOCKER_CLI is not set
# BR2_PACKAGE_DOCKER_CLI_BUILDX is not set
#
# docker-compose needs docker-cli and a toolchain w/ threads
#
# BR2_PACKAGE_DOCKER_ENGINE is not set
# BR2_PACKAGE_EARLYOOM is not set
# BR2_PACKAGE_EFIBOOTMGR is not set
BR2_PACKAGE_EFIVAR_ARCH_SUPPORTS=y
# BR2_PACKAGE_EFIVAR is not set
# BR2_PACKAGE_EMBIGGEN_DISK is not set
# BR2_PACKAGE_EMLOG is not set
# BR2_PACKAGE_FLUENT_BIT is not set
# BR2_PACKAGE_FTOP is not set
# BR2_PACKAGE_GETENT is not set
# BR2_PACKAGE_GKRELLM is not set
# BR2_PACKAGE_HTOP is not set
# BR2_PACKAGE_IBM_SW_TPM2 is not set
BR2_PACKAGE_INITSCRIPTS=y
#
# iotop depends on python3
#
# BR2_PACKAGE_IPRUTILS is not set
# BR2_PACKAGE_IRQBALANCE is not set
# BR2_PACKAGE_JAILHOUSE is not set
# BR2_PACKAGE_KEYUTILS is not set
# BR2_PACKAGE_KMOD is not set
# BR2_PACKAGE_KMON is not set
# BR2_PACKAGE_KVMTOOL is not set
# BR2_PACKAGE_LIBOSTREE is not set
BR2_PACKAGE_LIBVIRT_ARCH_SUPPORTS=y
#
# libvirt needs udev /dev management, a toolchain w/ threads, dynamic library, wchar, kernel headers >= 3.12 (4.11 for AArch64)
#
# BR2_PACKAGE_LXC is not set
BR2_PACKAGE_MAKEDUMPFILE_ARCH_SUPPORTS=y
# BR2_PACKAGE_MAKEDUMPFILE is not set
# BR2_PACKAGE_MENDER is not set
# BR2_PACKAGE_MENDER_CONNECT is not set
# BR2_PACKAGE_MFOC is not set
# BR2_PACKAGE_MOBY_BUILDKIT is not set
# BR2_PACKAGE_MOKUTIL is not set
#
# mokutil needs a toolchain w/ dynamic library, threads, gcc >= 4.9, headers >= 3.12
#
# BR2_PACKAGE_MONIT is not set
#
# multipath-tools needs udev and a toolchain w/ threads, dynamic library, C++
#
# BR2_PACKAGE_NCDU is not set
# BR2_PACKAGE_NERDCTL is not set
#
# netifrc needs openrc as init system
#
# BR2_PACKAGE_NUMACTL is not set
#
# nut needs a toolchain w/ C++, threads
#
BR2_PACKAGE_OPENVMTOOLS_ARCH_SUPPORTS=y
# BR2_PACKAGE_OPENVMTOOLS is not set
#
# pamtester depends on linux-pam
#
#
# petitboot needs a toolchain w/ wchar, dynamic library, threads, udev /dev management
#
# BR2_PACKAGE_POLKIT is not set
# BR2_PACKAGE_PROCRANK_LINUX is not set
# BR2_PACKAGE_PROCS is not set
# BR2_PACKAGE_PWGEN is not set
# BR2_PACKAGE_QBEE_AGENT is not set
# BR2_PACKAGE_QUOTA is not set
# BR2_PACKAGE_QUOTATOOL is not set
# BR2_PACKAGE_RAUC is not set
# BR2_PACKAGE_RAUC_HAWKBIT_UPDATER is not set
# BR2_PACKAGE_RUNC is not set
# BR2_PACKAGE_S6 is not set
# BR2_PACKAGE_S6_LINUX_INIT is not set
# BR2_PACKAGE_S6_LINUX_UTILS is not set
# BR2_PACKAGE_S6_PORTABLE_UTILS is not set
# BR2_PACKAGE_S6_RC is not set
# BR2_PACKAGE_SCRUB is not set
# BR2_PACKAGE_SCRYPT is not set
#
# sdbus-c++ needs systemd and a toolchain w/ C++, gcc >= 8
#
#
# sdbusplus needs systemd and a toolchain w/ C++, gcc >= 7
#
# BR2_PACKAGE_SEATD is not set
# BR2_PACKAGE_SHADOW is not set
# BR2_PACKAGE_SMACK is not set
#
# supervisor needs a python interpreter
#
# BR2_PACKAGE_SWUPDATE is not set
BR2_PACKAGE_SYSTEMD_ARCH_SUPPORTS=y
BR2_PACKAGE_SYSTEMD_BOOTCHART_ARCH_SUPPORTS=y
# BR2_PACKAGE_TEALDEER is not set
# BR2_PACKAGE_TPM_TOOLS is not set
# BR2_PACKAGE_TPM2_ABRMD is not set
# BR2_PACKAGE_TPM2_TOOLS is not set
# BR2_PACKAGE_TPM2_TOTP is not set
# BR2_PACKAGE_UNSCD is not set
# BR2_PACKAGE_UTIL_LINUX is not set
# BR2_PACKAGE_WATCHDOG is not set
# BR2_PACKAGE_WATCHDOGD is not set
# BR2_PACKAGE_XDG_DBUS_PROXY is not set
# BR2_PACKAGE_XEN is not set
BR2_PACKAGE_XVISOR_ARCH_SUPPORTS=y
# BR2_PACKAGE_XVISOR is not set
#
# Text editors and viewers
#
# BR2_PACKAGE_BAT is not set
# BR2_PACKAGE_ED is not set
# BR2_PACKAGE_JOE is not set
# BR2_PACKAGE_MC is not set
# BR2_PACKAGE_MG is not set
# BR2_PACKAGE_MOST is not set
# BR2_PACKAGE_NANO is not set
# BR2_PACKAGE_UEMACS is not set
#
# Filesystem images
#
# BR2_TARGET_ROOTFS_AXFS is not set
# BR2_TARGET_ROOTFS_BTRFS is not set
# BR2_TARGET_ROOTFS_CLOOP is not set
# BR2_TARGET_ROOTFS_CPIO is not set
# BR2_TARGET_ROOTFS_CRAMFS is not set
# BR2_TARGET_ROOTFS_EROFS is not set
BR2_TARGET_ROOTFS_EXT2=y
# BR2_TARGET_ROOTFS_EXT2_2r0 is not set
# BR2_TARGET_ROOTFS_EXT2_2r1 is not set
# BR2_TARGET_ROOTFS_EXT2_3 is not set
BR2_TARGET_ROOTFS_EXT2_4=y
BR2_TARGET_ROOTFS_EXT2_GEN=4
BR2_TARGET_ROOTFS_EXT2_REV=1
BR2_TARGET_ROOTFS_EXT2_LABEL="rootfs"
BR2_TARGET_ROOTFS_EXT2_SIZE="120M"
BR2_TARGET_ROOTFS_EXT2_INODES=0
BR2_TARGET_ROOTFS_EXT2_INODE_SIZE=256
BR2_TARGET_ROOTFS_EXT2_RESBLKS=5
BR2_TARGET_ROOTFS_EXT2_MKFS_OPTIONS="-O ^64bit"
BR2_TARGET_ROOTFS_EXT2_NONE=y
# BR2_TARGET_ROOTFS_EXT2_GZIP is not set
# BR2_TARGET_ROOTFS_EXT2_BZIP2 is not set
# BR2_TARGET_ROOTFS_EXT2_LZ4 is not set
# BR2_TARGET_ROOTFS_EXT2_LZMA is not set
# BR2_TARGET_ROOTFS_EXT2_LZO is not set
# BR2_TARGET_ROOTFS_EXT2_XZ is not set
# BR2_TARGET_ROOTFS_EXT2_ZSTD is not set
# BR2_TARGET_ROOTFS_F2FS is not set
# BR2_TARGET_ROOTFS_INITRAMFS is not set
# BR2_TARGET_ROOTFS_JFFS2 is not set
# BR2_TARGET_ROOTFS_OCI is not set
# BR2_TARGET_ROOTFS_ROMFS is not set
# BR2_TARGET_ROOTFS_SQUASHFS is not set
BR2_TARGET_ROOTFS_TAR=y
BR2_TARGET_ROOTFS_TAR_NONE=y
# BR2_TARGET_ROOTFS_TAR_GZIP is not set
# BR2_TARGET_ROOTFS_TAR_BZIP2 is not set
# BR2_TARGET_ROOTFS_TAR_LZ4 is not set
# BR2_TARGET_ROOTFS_TAR_LZMA is not set
# BR2_TARGET_ROOTFS_TAR_LZO is not set
# BR2_TARGET_ROOTFS_TAR_XZ is not set
# BR2_TARGET_ROOTFS_TAR_ZSTD is not set
BR2_TARGET_ROOTFS_TAR_OPTIONS=""
# BR2_TARGET_ROOTFS_UBI is not set
# BR2_TARGET_ROOTFS_UBIFS is not set
# BR2_TARGET_ROOTFS_YAFFS2 is not set
#
# Bootloaders
#
BR2_TARGET_ARM_TRUSTED_FIRMWARE=y
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_LATEST_VERSION is not set
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_LATEST_LTS_2_10_VERSION is not set
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_LATEST_LTS_2_8_VERSION is not set
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION is not set
BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL=y
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_GIT is not set
BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call github,nxp-imx,imx-atf,lf-6.1.1-1.0.0)/imx-atf-lf-6.1.1-1.0.0.tar.gz"
BR2_TARGET_ARM_TRUSTED_FIRMWARE_VERSION="custom"
BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
BR2_TARGET_ARM_TRUSTED_FIRMWARE_TARGET_BOARD=""
BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_DTS_PATH=""
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_FIP is not set
BR2_TARGET_ARM_TRUSTED_FIRMWARE_BL31=y
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_BL31_UBOOT is not set
BR2_TARGET_ARM_TRUSTED_FIRMWARE_BL32_DEFAULT=y
BR2_TARGET_ARM_TRUSTED_FIRMWARE_NONE_AS_BL33=y
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33 is not set
BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_TARGETS=""
BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES=""
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_DEBUG is not set
BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="*.bin"
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_DTC is not set
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_ARM32_TOOLCHAIN is not set
# BR2_TARGET_ARM_TRUSTED_FIRMWARE_SSP is not set
BR2_TARGET_ARM_TRUSTED_FIRMWARE_SSP_LEVEL="strong"
# BR2_TARGET_BAREBOX is not set
# BR2_TARGET_BINARIES_MARVELL is not set
# BR2_TARGET_BOOT_WRAPPER_AARCH64 is not set
BR2_TARGET_EDK2_ARCH_SUPPORTS=y
# BR2_TARGET_EDK2 is not set
BR2_TARGET_GRUB2_ARCH_SUPPORTS=y
# BR2_TARGET_GRUB2 is not set
# BR2_TARGET_MV_DDR_MARVELL is not set
# BR2_TARGET_OPTEE_OS is not set
BR2_PACKAGE_SHIM_ARCH_SUPPORTS=y
# BR2_TARGET_SHIM is not set
# BR2_TARGET_TI_K3_BOOT_FIRMWARE is not set
# BR2_TARGET_TI_K3_R5_LOADER is not set
BR2_TARGET_UBOOT=y
BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
# BR2_TARGET_UBOOT_BUILD_SYSTEM_LEGACY is not set
# BR2_TARGET_UBOOT_LATEST_VERSION is not set
# BR2_TARGET_UBOOT_CUSTOM_VERSION is not set
BR2_TARGET_UBOOT_CUSTOM_TARBALL=y
# BR2_TARGET_UBOOT_CUSTOM_GIT is not set
# BR2_TARGET_UBOOT_CUSTOM_HG is not set
# BR2_TARGET_UBOOT_CUSTOM_SVN is not set
BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call github,nxp-imx,uboot-imx,lf-6.1.1-1.0.0)/uboot-imx-lf-6.1.1-1.0.0.tar.gz"
BR2_TARGET_UBOOT_VERSION="custom"
BR2_TARGET_UBOOT_PATCH=""
BR2_TARGET_UBOOT_USE_DEFCONFIG=y
# BR2_TARGET_UBOOT_USE_CUSTOM_CONFIG is not set
BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES=""
BR2_TARGET_UBOOT_DEFAULT_ENV_FILE=""
BR2_TARGET_UBOOT_NEEDS_DTC=y
# BR2_TARGET_UBOOT_NEEDS_PYTHON3 is not set
# BR2_TARGET_UBOOT_NEEDS_PYLIBFDT is not set
# BR2_TARGET_UBOOT_NEEDS_PYELFTOOLS is not set
BR2_TARGET_UBOOT_NEEDS_OPENSSL=y
# BR2_TARGET_UBOOT_NEEDS_LZOP is not set
BR2_TARGET_UBOOT_NEEDS_GNUTLS=y
# BR2_TARGET_UBOOT_NEEDS_UTIL_LINUX is not set
# BR2_TARGET_UBOOT_NEEDS_XXD is not set
# BR2_TARGET_UBOOT_NEEDS_ATF_BL31 is not set
# BR2_TARGET_UBOOT_NEEDS_IMX_FIRMWARE is not set
# BR2_TARGET_UBOOT_USE_BINMAN is not set
#
# U-Boot binary format
#
# BR2_TARGET_UBOOT_FORMAT_AIS is not set
BR2_TARGET_UBOOT_FORMAT_BIN=y
# BR2_TARGET_UBOOT_FORMAT_DTB is not set
# BR2_TARGET_UBOOT_FORMAT_DTB_BIN is not set
# BR2_TARGET_UBOOT_FORMAT_NAND_BIN is not set
# BR2_TARGET_UBOOT_FORMAT_ELF is not set
# BR2_TARGET_UBOOT_FORMAT_REMAKE_ELF is not set
# BR2_TARGET_UBOOT_FORMAT_IMG is not set
# BR2_TARGET_UBOOT_FORMAT_DTB_IMG is not set
# BR2_TARGET_UBOOT_FORMAT_IMX is not set
# BR2_TARGET_UBOOT_FORMAT_DTB_IMX is not set
# BR2_TARGET_UBOOT_FORMAT_ITB is not set
BR2_TARGET_UBOOT_FORMAT_CUSTOM=y
BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot-nodtb.bin"
BR2_TARGET_UBOOT_SPL=y
BR2_TARGET_UBOOT_SPL_NAME="spl/u-boot-spl.bin"
# BR2_TARGET_UBOOT_INITIAL_ENV is not set
# BR2_TARGET_UBOOT_ZYNQMP is not set
BR2_TARGET_UBOOT_CUSTOM_DTS_PATH=""
BR2_TARGET_UBOOT_CUSTOM_MAKEOPTS=""
# BR2_TARGET_VEXPRESS_FIRMWARE is not set
# BR2_TARGET_XILINX_PREBUILT is not set
#
# Host utilities
#
# BR2_PACKAGE_HOST_ABOOTIMG is not set
# BR2_PACKAGE_HOST_AESPIPE is not set
# BR2_PACKAGE_HOST_AGENT_PROXY is not set
# BR2_PACKAGE_HOST_AMLOGIC_BOOT_FIP is not set
# BR2_PACKAGE_HOST_ANDROID_TOOLS is not set
# BR2_PACKAGE_HOST_ASN1C is not set
# BR2_PACKAGE_HOST_BABELTRACE2 is not set
# BR2_PACKAGE_HOST_BMAP_TOOLS is not set
# BR2_PACKAGE_HOST_BOOTGEN is not set
# BR2_PACKAGE_HOST_BTRFS_PROGS is not set
# BR2_PACKAGE_HOST_CHECKPOLICY is not set
# BR2_PACKAGE_HOST_CHECKSEC is not set
# BR2_PACKAGE_HOST_CMAKE is not set
BR2_HOST_CMAKE_AT_LEAST="3.18"
# BR2_PACKAGE_HOST_COMPOSER is not set
# BR2_PACKAGE_HOST_CRAMFS is not set
# BR2_PACKAGE_HOST_CRUDINI is not set
# BR2_PACKAGE_HOST_CRYPTSETUP is not set
# BR2_PACKAGE_HOST_DBUS_PYTHON is not set
# BR2_PACKAGE_HOST_DELVE is not set
# BR2_PACKAGE_HOST_DEPOT_TOOLS is not set
# BR2_PACKAGE_HOST_DFU_UTIL is not set
# BR2_PACKAGE_HOST_DOS2UNIX is not set
BR2_PACKAGE_HOST_DOSFSTOOLS=y
# BR2_PACKAGE_HOST_DOXYGEN is not set
BR2_PACKAGE_HOST_DTC=y
BR2_PACKAGE_HOST_E2FSPROGS=y
# BR2_PACKAGE_HOST_E2TOOLS is not set
# BR2_PACKAGE_HOST_ENVIRONMENT_SETUP is not set
# BR2_PACKAGE_HOST_EROFS_UTILS is not set
# BR2_PACKAGE_HOST_EXFATPROGS is not set
# BR2_PACKAGE_HOST_F2FS_TOOLS is not set
# BR2_PACKAGE_HOST_FAKETIME is not set
# BR2_PACKAGE_HOST_FATCAT is not set
# BR2_PACKAGE_HOST_FIRMWARE_UTILS is not set
BR2_PACKAGE_HOST_FLUTTER_SDK_BIN_ARCH_SUPPORTS=y
# BR2_PACKAGE_HOST_FLUTTER_SDK_BIN is not set
# BR2_PACKAGE_HOST_FWUP is not set
# BR2_PACKAGE_HOST_GENEXT2FS is not set
BR2_PACKAGE_HOST_GENIMAGE=y
# BR2_PACKAGE_HOST_GENPART is not set
# BR2_PACKAGE_HOST_GNUPG is not set
# BR2_PACKAGE_HOST_GNUPG2 is not set
BR2_PACKAGE_HOST_GO_TARGET_ARCH_SUPPORTS=y
BR2_PACKAGE_HOST_GO_TARGET_CGO_LINKING_SUPPORTS=y
BR2_PACKAGE_HOST_GO_HOST_ARCH_SUPPORTS=y
BR2_PACKAGE_PROVIDES_HOST_GO="host-go-src"
BR2_PACKAGE_HOST_GO_BOOTSTRAP_STAGE1_ARCH_SUPPORTS=y
BR2_PACKAGE_HOST_GO_BOOTSTRAP_STAGE2_ARCH_SUPPORTS=y
BR2_PACKAGE_HOST_GO_BOOTSTRAP_STAGE3_ARCH_SUPPORTS=y
BR2_PACKAGE_HOST_GOOGLE_BREAKPAD_ARCH_SUPPORTS=y
# BR2_PACKAGE_HOST_GPTFDISK is not set
# BR2_PACKAGE_HOST_IMAGEMAGICK is not set
BR2_PACKAGE_HOST_IMX_MKIMAGE=y
# BR2_PACKAGE_HOST_IMX_USB_LOADER is not set
# BR2_PACKAGE_HOST_JQ is not set
# BR2_PACKAGE_HOST_JSMIN is not set
BR2_PACKAGE_HOST_KMOD=y
# BR2_PACKAGE_HOST_KMOD_GZ is not set
# BR2_PACKAGE_HOST_KMOD_ZSTD is not set
# BR2_PACKAGE_HOST_KMOD_XZ is not set
# BR2_PACKAGE_HOST_LIBP11 is not set
# BR2_PACKAGE_HOST_LLD is not set
# BR2_PACKAGE_HOST_LPC3250LOADER is not set
# BR2_PACKAGE_HOST_LTTNG_BABELTRACE is not set
# BR2_PACKAGE_HOST_LZMA_ALONE is not set
# BR2_PACKAGE_HOST_MENDER_ARTIFACT is not set
# BR2_PACKAGE_HOST_MESON_TOOLS is not set
# BR2_PACKAGE_HOST_MICROCHIP_HSS_PAYLOAD_GENERATOR is not set
# BR2_PACKAGE_HOST_MINISIGN is not set
# BR2_PACKAGE_HOST_MKPASSWD is not set
# BR2_PACKAGE_HOST_MOBY_BUILDKIT is not set
# BR2_PACKAGE_HOST_MOSQUITTO is not set
# BR2_PACKAGE_HOST_MTD is not set
BR2_PACKAGE_HOST_MTOOLS=y
BR2_PACKAGE_HOST_NODEJS_BIN_ARCH_SUPPORTS=y
# BR2_PACKAGE_HOST_NODEJS is not set
BR2_PACKAGE_PROVIDES_HOST_NODEJS="host-nodejs-bin"
# BR2_PACKAGE_HOST_ODB is not set
# BR2_PACKAGE_HOST_OPENOCD is not set
# BR2_PACKAGE_HOST_OPKG_UTILS is not set
# BR2_PACKAGE_HOST_PAHOLE is not set
# BR2_PACKAGE_HOST_PARTED is not set
BR2_PACKAGE_HOST_PATCHELF=y
# BR2_PACKAGE_HOST_PIGZ is not set
# BR2_PACKAGE_HOST_PKGCONF is not set
# BR2_PACKAGE_HOST_PWGEN is not set
# BR2_PACKAGE_HOST_PYTHON_CYTHON is not set
# BR2_PACKAGE_HOST_PYTHON_GREENLET is not set
# BR2_PACKAGE_HOST_PYTHON_INIPARSE is not set
# BR2_PACKAGE_HOST_PYTHON_LXML is not set
# BR2_PACKAGE_HOST_PYTHON_PYYAML is not set
# BR2_PACKAGE_HOST_PYTHON_SIX is not set
# BR2_PACKAGE_HOST_PYTHON_USWID is not set
# BR2_PACKAGE_HOST_PYTHON_XLRD is not set
# BR2_PACKAGE_HOST_PYTHON3 is not set
BR2_PACKAGE_HOST_QEMU_ARCH_SUPPORTS=y
BR2_PACKAGE_HOST_QEMU_SYSTEM_ARCH_SUPPORTS=y
BR2_PACKAGE_HOST_QEMU_USER_ARCH_SUPPORTS=y
# BR2_PACKAGE_HOST_QEMU is not set
# BR2_PACKAGE_HOST_QORIQ_RCW is not set
# BR2_PACKAGE_HOST_RASPBERRYPI_USBBOOT is not set
# BR2_PACKAGE_HOST_RAUC is not set
# BR2_PACKAGE_HOST_RISCV_ISA_SIM is not set
# BR2_PACKAGE_HOST_RUNC is not set
BR2_PACKAGE_HOST_RUSTC_ARCH_SUPPORTS=y
BR2_PACKAGE_HOST_RUSTC_TARGET_TIER1_PLATFORMS=y
BR2_PACKAGE_HOST_RUSTC_TARGET_ARCH_SUPPORTS=y
BR2_PACKAGE_HOST_RUSTC_ARCH="aarch64"
# BR2_PACKAGE_HOST_RUSTC is not set
BR2_PACKAGE_PROVIDES_HOST_RUSTC="host-rust-bin"
# BR2_PACKAGE_HOST_SAM_BA is not set
# BR2_PACKAGE_HOST_SDBUS_CPP is not set
# BR2_PACKAGE_HOST_SDBUSPLUS is not set
# BR2_PACKAGE_HOST_SENTRY_CLI is not set
# BR2_PACKAGE_HOST_SKOPEO is not set
# BR2_PACKAGE_HOST_SLOCI_IMAGE is not set
# BR2_PACKAGE_HOST_SQUASHFS is not set
# BR2_PACKAGE_HOST_SWIG is not set
# BR2_PACKAGE_HOST_SWTPM is not set
# BR2_PACKAGE_HOST_SWUGENERATOR is not set
# BR2_PACKAGE_HOST_TIPIDEE is not set
BR2_PACKAGE_HOST_UBOOT_TOOLS=y
BR2_PACKAGE_HOST_UBOOT_TOOLS_FIT_SUPPORT=y
# BR2_PACKAGE_HOST_UBOOT_TOOLS_FIT_SIGNATURE_SUPPORT is not set
# BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE is not set
# BR2_PACKAGE_HOST_UBOOT_TOOLS_BOOT_SCRIPT is not set
BR2_PACKAGE_HOST_UTIL_LINUX=y
# BR2_PACKAGE_HOST_UTP_COM is not set
# BR2_PACKAGE_HOST_UUU is not set
# BR2_PACKAGE_HOST_VBOOT_UTILS is not set
# BR2_PACKAGE_HOST_XORRISO is not set
# BR2_PACKAGE_HOST_ZIP is not set
# BR2_PACKAGE_HOST_ZSTD is not set
#
# Legacy config options
#
#
# Legacy options removed in 2024.08
#
# BR2_PACKAGE_MIDORI is not set
# BR2_PACKAGE_FROTZ is not set
# BR2_PACKAGE_FAN_CTRL is not set
# BR2_PACKAGE_FLUTTER_DYNAMIC_LAYOUTS_EXAMPLE is not set
# BR2_KERNEL_HEADERS_6_9 is not set
# BR2_x86_knightslanding is not set
# BR2_x86_knightsmill is not set
# BR2_PACKAGE_DVB_APPS is not set
# BR2_PACKAGE_GAMIN is not set
# BR2_PACKAGE_CAIRO_SVG is not set
# BR2_PACKAGE_CAIRO_SCRIPT is not set
# BR2_PACKAGE_CAIRO_PS is not set
# BR2_PACKAGE_CAIRO_PDF is not set
# BR2_PACKAGE_CAIRO_XML is not set
# BR2_GDB_VERSION_12 is not set
# BR2_TARGET_BEAGLEV_DDRINIT is not set
# BR2_TARGET_BEAGLEV_SECONDBOOT is not set
# BR2_PACKAGE_ONEVPL_INTEL_GPU is not set
# BR2_PACKAGE_CGIC is not set
# BR2_PACKAGE_BEECRYPT is not set
# BR2_PACKAGE_VERSAL_FIRMWARE is not set
# BR2_KERNEL_HEADERS_6_8 is not set
# BR2_TARGET_AT91BOOTSTRAP is not set
# BR2_TARGET_AT91DATAFLASHBOOT is not set
# BR2_PACKAGE_ON2_8170_MODULES is not set
# BR2_PACKAGE_ON2_8170_LIBS is not set
# BR2_GCC_VERSION_11_X is not set
# BR2_BINFMT_FLAT_SHARED is not set
# BR2_PACKAGE_OMXPLAYER is not set
# BR2_KERNEL_HEADERS_6_7 is not set
# BR2_TARGET_TI_K3_IMAGE_GEN is not set
# BR2_TARGET_UBOOT_NEEDS_TI_K3_DM is not set
# BR2_PACKAGE_FLUTTER_GALLERY is not set
# BR2_TOOLCHAIN_EXTERNAL_CODESCAPE_IMG_MIPS is not set
# BR2_TOOLCHAIN_EXTERNAL_CODESCAPE_MTI_MIPS is not set
# BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_AARCH64 is not set
# BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_ARM is not set
# BR2_BINUTILS_VERSION_2_39_X is not set
#
# Legacy options removed in 2024.02
#
# BR2_PACKAGE_MYSQL is not set
# BR2_PACKAGE_ORACLE_MYSQL is not set
# BR2_PACKAGE_STRONGSWAN_SCEP is not set
# BR2_PACKAGE_SHADOW_UTMPX is not set
# BR2_PACKAGE_TINYMEMBENCH is not set
# BR2_PACKAGE_DAVINCI_BOOTCOUNT is not set
# BR2_PACKAGE_PYTHON_CROSSBAR is not set
# BR2_PACKAGE_PYTHON_PYGAME is not set
# BR2_KERNEL_HEADERS_4_14 is not set
# BR2_PACKAGE_LIBCAMERA_PIPELINE_RASPBERRYPI is not set
# BR2_GDB_VERSION_11 is not set
# BR2_PACKAGE_LIBMPD is not set
# BR2_PACKAGE_GMPC is not set
# BR2_PACKAGE_FLICKCURL is not set
# BR2_PACKAGE_ONEVPL is not set
# BR2_KERNEL_HEADERS_6_5 is not set
BR2_PACKAGE_WATCHDOGD_GENERIC_POLL=0
BR2_PACKAGE_WATCHDOGD_LOADAVG_POLL=0
BR2_PACKAGE_WATCHDOGD_FILENR_POLL=0
BR2_PACKAGE_WATCHDOGD_MEMINFO_POLL=0
#
# Legacy options removed in 2023.11
#
# BR2_PACKAGE_PYTHON_PYXB is not set
# BR2_PACKAGE_OPENJDK_VERSION_11 is not set
# BR2_KERNEL_HEADERS_6_4 is not set
# BR2_PACKAGE_GOOGLE_MATERIAL_DESIGN_ICONS is not set
# BR2_GDB_VERSION_10 is not set
#
# Legacy options removed in 2023.08
#
# BR2_TARGET_LPC32XXCDL is not set
# BR2_BINUTILS_VERSION_2_38_X is not set
# BR2_GCC_VERSION_10_X is not set
# BR2_KERNEL_HEADERS_6_3 is not set
# BR2_PACKAGE_TOVID is not set
# BR2_PACKAGE_LIBASPLIB is not set
# BR2_PACKAGE_OCF_LINUX is not set
# BR2_BINUTILS_VERSION_2_37_X is not set
#
# Legacy options removed in 2023.05
#
# BR2_KERNEL_HEADERS_6_2 is not set
# BR2_PACKAGE_ATK is not set
# BR2_PACKAGE_AT_SPI2_ATK is not set
# BR2_PACKAGE_OPTEE_BENCHMARK is not set
# BR2_PACAKGE_OPENFPGALOADER_CMSIS is not set
#
# Legacy options removed in 2023.02
#
# BR2_PACKAGE_PUGIXML_HEADER_ONLY is not set
# BR2_PACKAGE_UCCP420WLAN is not set
# BR2_PACKAGE_IMX_GPU_G2D_EXAMPLES is not set
# BR2_KERNEL_HEADERS_6_0 is not set
# BR2_KERNEL_HEADERS_4_9 is not set
# BR2_PACKAGE_DOCKER_PROXY is not set
# BR2_PACKAGE_PYTHON_BUNCH is not set
# BR2_TARGET_GUMMIBOOT is not set
# BR2_PACKAGE_IPUTILS_NINFOD is not set
# BR2_PACKAGE_IPUTILS_RARPD is not set
# BR2_PACKAGE_IPUTILS_RDISC is not set
# BR2_PACKAGE_IPUTILS_RDISC_SERVER is not set
# BR2_PACKAGE_GST1_PLUGINS_UGLY_PLUGIN_XINGMUX is not set
# BR2_PACKAGE_GST1_PLUGINS_BASE_PLUGIN_VIDEOSCALE is not set
# BR2_PACKAGE_GST1_PLUGINS_BASE_PLUGIN_VIDEOCONVERT is not set
# BR2_PACKAGE_IMX_GPU_VIV_OUTPUT_X11 is not set
# BR2_PACKAGE_XDRIVER_XF86_VIDEO_IMX_VIV is not set
BR2_PACKAGE_QEMU_CUSTOM_TARGETS=""
# BR2_PACKAGE_XDRIVER_XF86_INPUT_KEYBOARD is not set
# BR2_TARGET_SUN20I_D1_SPL is not set
# BR2_PACKAGE_PYTHON_M2R is not set
# BR2_PACKAGE_MESA3D_XVMC is not set
# BR2_KERNEL_HEADERS_5_19 is not set
# BR2_PACKAGE_XDRIVER_XF86_VIDEO_TGA is not set
# BR2_PACKAGE_XDRIVER_XF86_VIDEO_GLINT is not set
# BR2_PACKAGE_USBREDIR_SERVER is not set
#
# Legacy options removed in 2022.11
#
# BR2_BINUTILS_VERSION_2_36_X is not set
# BR2_PACKAGE_RABBITMQ_SERVER is not set
# BR2_PACKAGE_LIBOPENSSL_ENABLE_RC5 is not set
# BR2_PACKAGE_LIBDCADEC is not set
# BR2_KERNEL_HEADERS_5_17 is not set
# BR2_iwmmxt is not set
# BR2_PACKAGE_UHD_N230 is not set
# BR2_PACKAGE_UHD_RFNOC is not set
# BR2_PACKAGE_GPSD_OLDSTYLE is not set
# BR2_GDB_VERSION_9_2 is not set
#
# Legacy options removed in 2022.08
#
# BR2_ECLIPSE_REGISTER is not set
# BR2_csky is not set
# BR2_PACKAGE_MESA3D_DRI_DRIVER_I915 is not set
# BR2_PACKAGE_MESA3D_DRI_DRIVER_I965 is not set
# BR2_PACKAGE_MESA3D_DRI_DRIVER_NOUVEAU is not set
# BR2_PACKAGE_MESA3D_DRI_DRIVER_RADEON is not set
# BR2_GCC_VERSION_9_X is not set
# BR2_PACKAGE_PHP_EXT_WDDX is not set
# BR2_nds32 is not set
# BR2_PACKAGE_RTL8723BS is not set
#
# Legacy options removed in 2022.05
#
# BR2_PACKAGE_KTAP is not set
# BR2_KERNEL_HEADERS_5_16 is not set
# BR2_KERNEL_HEADERS_4_4 is not set
# BR2_BINUTILS_VERSION_2_32_X is not set
# BR2_sh2a is not set
# BR2_BINUTILS_VERSION_2_35_X is not set
# BR2_PACKAGE_BOOST_LAYOUT_TAGGED is not set
# BR2_PACKAGE_BOOST_LAYOUT_VERSIONED is not set
#
# Legacy options removed in 2022.02
#
BR2_TARGET_ROOTFS_OCI_ENTRYPOINT_ARGS=""
# BR2_PACKAGE_LIBCURL_LIBNSS is not set
# BR2_PACKAGE_WESTON_DEFAULT_FBDEV is not set
# BR2_PACKAGE_WESTON_FBDEV is not set
# BR2_PACKAGE_PYTHON_PYCLI is not set
# BR2_PACKAGE_LINUX_TOOLS_BPFTOOL is not set
# BR2_TARGET_UBOOT_NEEDS_PYTHON2 is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_LIBMMS is not set
# BR2_PACKAGE_PYTHON_FUNCTOOLS32 is not set
# BR2_PACKAGE_PYTHON_ENUM34 is not set
# BR2_PACKAGE_PYTHON_ENUM is not set
# BR2_PACKAGE_PYTHON_DIALOG is not set
# BR2_PACKAGE_PYTHON_YIELDFROM is not set
# BR2_PACKAGE_PYTHON_TYPING is not set
# BR2_PACKAGE_PYTHON_SUBPROCESS32 is not set
# BR2_PACKAGE_PYTHON_SINGLEDISPATCH is not set
# BR2_PACKAGE_PYTHON_PYRO is not set
# BR2_PACKAGE_PYTHON_PYPCAP is not set
# BR2_PACKAGE_PYTHON_PATHLIB2 is not set
# BR2_PACKAGE_PYTHON_PAM is not set
# BR2_PACKAGE_PYTHON_NFC is not set
# BR2_PACKAGE_PYTHON_MAD is not set
# BR2_PACKAGE_PYTHON_IPADDRESS is not set
# BR2_PACKAGE_PYTHON_IPADDR is not set
# BR2_PACKAGE_PYTHON_ID3 is not set
# BR2_PACKAGE_PYTHON_FUTURES is not set
# BR2_PACKAGE_PYTHON_BACKPORTS_SSL_MATCH_HOSTNAME is not set
# BR2_PACKAGE_PYTHON_BACKPORTS_SHUTIL_GET_TERMINAL_SIZE is not set
# BR2_PACKAGE_PYTHON_BACKPORTS_ABC is not set
# BR2_PACKAGE_PYTHON is not set
# BR2_TARGET_UBOOT_ZYNQ_IMAGE is not set
# BR2_PACKAGE_RPI_BT_FIRMWARE is not set
# BR2_PACKAGE_RPI_WIFI_FIRMWARE is not set
# BR2_PACKAGE_HOST_GDB_PYTHON is not set
# BR2_PACKAGE_GSTREAMER1_MM is not set
# BR2_KERNEL_HEADERS_5_14 is not set
# BR2_PACKAGE_PYTHON_BACKPORTS_FUNCTOOLS_LRU_CACHE is not set
# BR2_PACKAGE_CIVETWEB_WITH_LUA is not set
# BR2_PACKAGE_SUNXI_MALI_MAINLINE_DRIVER is not set
# BR2_PACKAGE_SUNXI_MALI_MAINLINE is not set
# BR2_PACKAGE_SUNXI_MALI_MAINLINE_R6P2 is not set
# BR2_PACKAGE_SUNXI_MALI_MAINLINE_R8P1 is not set
# BR2_PACKAGE_QT5WEBKIT_EXAMPLES is not set
# BR2_TOOLCHAIN_EXTERNAL_BOOTLIN_RISCV64_GLIBC_BLEEDING_EDGE is not set
# BR2_TOOLCHAIN_EXTERNAL_BOOTLIN_RISCV64_MUSL_BLEEDING_EDGE is not set
# BR2_PACKAGE_IPUTILS_TFTPD is not set
# BR2_PACKAGE_IPUTILS_TRACEROUTE6 is not set
# BR2_PACKAGE_LIBMEDIAART_BACKEND_NONE is not set
# BR2_PACKAGE_MPD_UPNP is not set
#
# Legacy options removed in 2021.11
#
# BR2_OPENJDK_VERSION_LTS is not set
# BR2_OPENJDK_VERSION_LATEST is not set
# BR2_PACKAGE_MPD_TIDAL is not set
# BR2_PACKAGE_MROUTED_RSRR is not set
# BR2_BINUTILS_VERSION_CSKY is not set
# BR2_GCC_VERSION_CSKY is not set
# BR2_PACKAGE_CANFESTIVAL is not set
# BR2_PACKAGE_NMAP_NDIFF is not set
# BR2_GDB_VERSION_8_3 is not set
# BR2_PACKAGE_PYTHON_MELD3 is not set
# BR2_PACKAGE_STRONGSWAN_EAP is not set
# BR2_PACKAGE_GNURADIO_PAGER is not set
# BR2_KERNEL_HEADERS_5_11 is not set
# BR2_KERNEL_HEADERS_5_12 is not set
# BR2_KERNEL_HEADERS_5_13 is not set
#
# Legacy options removed in 2021.08
#
BR2_TARGET_GRUB2_BUILTIN_MODULES=""
BR2_TARGET_GRUB2_BUILTIN_CONFIG=""
# BR2_PACKAGE_LIBMCRYPT is not set
# BR2_PACKAGE_MCRYPT is not set
# BR2_PACKAGE_PHP_EXT_MCRYPT is not set
# BR2_BINUTILS_VERSION_2_34_X is not set
# BR2_PACKAGE_LIBSOIL is not set
# BR2_PACKAGE_CLAPACK is not set
# BR2_PACKAGE_SPIDERMONKEY is not set
# BR2_PACKAGE_KODI_LIBVA is not set
# BR2_PACKAGE_PYTHON_COHERENCE is not set
# BR2_PACKAGE_PHP_EXT_XMLRPC is not set
# BR2_GCC_VERSION_8_X is not set
#
# Legacy options removed in 2021.05
#
# BR2_PACKAGE_UDISKS_LVM2 is not set
# BR2_PACKAGE_LVM2_APP_LIBRARY is not set
# BR2_PACKAGE_LVM2_LVMETAD is not set
# BR2_PACKAGE_MONKEY is not set
# BR2_PACKAGE_DOCKER_CONTAINERD is not set
# BR2_PACKAGE_IOSTAT is not set
# BR2_PACKAGE_SCONESERVER_HTTP_SCONESITE_IMAGE is not set
# BR2_PACKAGE_XSERVER_XORG_SERVER_KDRIVE_EVDEV is not set
# BR2_PACKAGE_XSERVER_XORG_SERVER_KDRIVE_KBD is not set
# BR2_PACKAGE_XSERVER_XORG_SERVER_KDRIVE_MOUSE is not set
# BR2_PACKAGE_MESA3D_OSMESA_CLASSIC is not set
# BR2_PACKAGE_MESA3D_DRI_DRIVER_SWRAST is not set
# BR2_PACKAGE_KODI_SCREENSAVER_CRYSTALMORPH is not set
#
# Legacy options removed in 2021.02
#
# BR2_PACKAGE_MPD_AUDIOFILE is not set
# BR2_PACKAGE_AUDIOFILE is not set
# BR2_BINUTILS_VERSION_2_33_X is not set
# BR2_PACKAGE_LIBUPNP18 is not set
# BR2_PACKAGE_BOA is not set
# BR2_PACKAGE_LINUX_FIRMWARE_IMX_SDMA is not set
# BR2_GDB_VERSION_8_2 is not set
# BR2_PACKAGE_HOST_RCW is not set
# BR2_KERNEL_HEADERS_5_9 is not set
# BR2_KERNEL_HEADERS_5_8 is not set
# BR2_powerpc_601 is not set
# BR2_PACKAGE_TI_SGX_LIBGBM is not set
# BR2_PACKAGE_IPSEC_TOOLS is not set
#
# Legacy options removed in 2020.11
#
# BR2_PACKAGE_GPSD_FIXED_PORT_SPEED is not set
# BR2_PACKAGE_GPSD_RECONFIGURE is not set
# BR2_PACKAGE_GPSD_CONTROLSEND is not set
# BR2_PACKAGE_OPENCV is not set
# BR2_PACKAGE_LIBCROCO is not set
# BR2_PACKAGE_BELLAGIO is not set
# BR2_PACKAGE_SYSTEMD_JOURNAL_GATEWAY is not set
# BR2_TARGET_UBOOT_BOOT_SCRIPT is not set
# BR2_TARGET_UBOOT_ENVIMAGE is not set
# BR2_PACKAGE_KISMET_CLIENT is not set
# BR2_PACKAGE_KISMET_DRONE is not set
# BR2_GCC_VERSION_7_X is not set
# BR2_PACKAGE_GST1_VALIDATE is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_YADIF is not set
# BR2_PACKAGE_GQVIEW is not set
# BR2_PACKAGE_WESTON_IMX is not set
# BR2_KERNEL_HEADERS_5_7 is not set
# BR2_PACKAGE_TINYHTTPD is not set
# BR2_PACKAGE_XSERVER_XORG_SERVER_AIGLX is not set
# BR2_PACKAGE_AMD_CATALYST is not set
# BR2_PACKAGE_NVIDIA_TEGRA23 is not set
# BR2_GDB_VERSION_8_1 is not set
#
# Legacy options removed in 2020.08
#
# BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_AMD64 is not set
# BR2_KERNEL_HEADERS_5_6 is not set
# BR2_KERNEL_HEADERS_5_5 is not set
# BR2_BINUTILS_VERSION_2_31_X is not set
# BR2_PACKAGE_KODI_PERIPHERAL_STEAMCONTROLLER is not set
#
# Legacy options removed in 2020.05
#
# BR2_PACKAGE_WIRINGPI is not set
# BR2_PACKAGE_PYTHON_PYCRYPTO is not set
# BR2_PACKAGE_MTDEV2TUIO is not set
# BR2_PACKAGE_EZXML is not set
# BR2_PACKAGE_COLLECTD_LVM is not set
# BR2_PACKAGE_PYTHON_PYASN is not set
# BR2_PACKAGE_PYTHON_PYASN_MODULES is not set
# BR2_PACKAGE_LINUX_FIRMWARE_ATHEROS_10K_QCA6174 is not set
# BR2_PACKAGE_QT5CANVAS3D is not set
# BR2_PACKAGE_KODI_LIBTHEORA is not set
# BR2_PACKAGE_CEGUI06 is not set
# BR2_GCC_VERSION_5_X is not set
#
# Legacy options removed in 2020.02
#
# BR2_PACKAGE_JAMVM is not set
# BR2_PACKAGE_CLASSPATH is not set
# BR2_PACKAGE_QT5_VERSION_5_6 is not set
# BR2_PACKAGE_CURL is not set
# BR2_PACKAGE_GSTREAMER is not set
# BR2_PACKAGE_NVIDIA_TEGRA23_BINARIES_GSTREAMER_PLUGINS is not set
# BR2_PACKAGE_NVIDIA_TEGRA23_BINARIES_NV_SAMPLE_APPS is not set
# BR2_PACKAGE_FREERDP_GSTREAMER is not set
# BR2_PACKAGE_OPENCV3_WITH_GSTREAMER is not set
# BR2_PACKAGE_OPENCV_WITH_GSTREAMER is not set
# BR2_PACKAGE_LIBPLAYER is not set
# BR2_GCC_VERSION_OR1K is not set
# BR2_PACKAGE_BLUEZ_UTILS is not set
# BR2_PACKAGE_GADGETFS_TEST is not set
# BR2_PACKAGE_FIS is not set
BR2_PACKAGE_REFPOLICY_POLICY_VERSION=""
# BR2_PACKAGE_CELT051 is not set
# BR2_PACKAGE_WIREGUARD is not set
# BR2_PACKAGE_PERL_NET_PING is not set
# BR2_PACKAGE_PERL_MIME_BASE64 is not set
# BR2_PACKAGE_PERL_DIGEST_MD5 is not set
# BR2_PACKAGE_ERLANG_P1_ICONV is not set
# BR2_KERNEL_HEADERS_5_3 is not set
# BR2_PACKAGE_PYTHON_SCAPY3K is not set
# BR2_BINUTILS_VERSION_2_30_X is not set
# BR2_PACKAGE_RPI_USERLAND_START_VCFILED is not set
# BR2_PACKAGE_TI_SGX_KM_AM335X is not set
# BR2_PACKAGE_TI_SGX_KM_AM437X is not set
# BR2_PACKAGE_TI_SGX_KM_AM4430 is not set
# BR2_PACKAGE_TI_SGX_KM_AM5430 is not set
#
# Legacy options removed in 2019.11
#
# BR2_PACKAGE_OPENVMTOOLS_PROCPS is not set
# BR2_PACKAGE_ALLJOYN is not set
# BR2_PACKAGE_ALLJOYN_BASE is not set
# BR2_PACKAGE_ALLJOYN_BASE_CONTROLPANEL is not set
# BR2_PACKAGE_ALLJOYN_BASE_NOTIFICATION is not set
# BR2_PACKAGE_ALLJOYN_BASE_ONBOARDING is not set
# BR2_PACKAGE_ALLJOYN_TCL_BASE is not set
# BR2_PACKAGE_ALLJOYN_TCL is not set
BR2_TOOLCHAIN_EXTRA_EXTERNAL_LIBS=""
# BR2_PACKAGE_PYTHON_PYSNMP_APPS is not set
# BR2_KERNEL_HEADERS_5_2 is not set
# BR2_TARGET_RISCV_PK is not set
# BR2_PACKAGE_SQLITE_STAT3 is not set
# BR2_KERNEL_HEADERS_5_1 is not set
# BR2_PACKAGE_DEVMEM2 is not set
# BR2_PACKAGE_USTR is not set
# BR2_PACKAGE_KODI_SCREENSAVER_PLANESTATE is not set
# BR2_PACKAGE_KODI_VISUALISATION_WAVEFORHUE is not set
# BR2_PACKAGE_KODI_AUDIODECODER_OPUS is not set
# BR2_PACKAGE_MESA3D_OSMESA is not set
# BR2_PACKAGE_HOSTAPD_DRIVER_RTW is not set
# BR2_PACKAGE_WPA_SUPPLICANT_DBUS_NEW is not set
# BR2_PACKAGE_WPA_SUPPLICANT_DBUS_OLD is not set
#
# Legacy options removed in 2019.08
#
# BR2_TARGET_TS4800_MBRBOOT is not set
# BR2_PACKAGE_LIBAMCODEC is not set
# BR2_PACKAGE_ODROID_SCRIPTS is not set
# BR2_PACKAGE_ODROID_MALI is not set
# BR2_PACKAGE_KODI_PLATFORM_AML is not set
# BR2_GCC_VERSION_6_X is not set
# BR2_GCC_VERSION_4_9_X is not set
# BR2_GDB_VERSION_7_12 is not set
# BR2_PACKAGE_XAPP_MKFONTDIR is not set
# BR2_GDB_VERSION_8_0 is not set
# BR2_KERNEL_HEADERS_4_20 is not set
# BR2_KERNEL_HEADERS_5_0 is not set
#
# Legacy options removed in 2019.05
#
# BR2_CSKY_DSP is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_COMPOSITOR is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_IQA is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_OPENCV is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_STEREO is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_VCD is not set
# BR2_PACKAGE_LUNIT is not set
# BR2_PACKAGE_FFMPEG_FFSERVER is not set
# BR2_PACKAGE_LIBUMP is not set
# BR2_PACKAGE_SUNXI_MALI is not set
# BR2_BINUTILS_VERSION_2_29_X is not set
# BR2_BINUTILS_VERSION_2_28_X is not set
# BR2_PACKAGE_GST_PLUGINS_BAD_PLUGIN_APEXSINK is not set
#
# Legacy options removed in 2019.02
#
# BR2_PACKAGE_QT is not set
# BR2_PACKAGE_QTUIO is not set
# BR2_PACKAGE_PINENTRY_QT4 is not set
# BR2_PACKAGE_POPPLER_QT is not set
# BR2_PACKAGE_OPENCV3_WITH_QT is not set
# BR2_PACKAGE_OPENCV_WITH_QT is not set
# BR2_PACKAGE_AMD_CATALYST_CCCLE is not set
# BR2_PACKAGE_SDL_QTOPIA is not set
# BR2_PACKAGE_PYTHON_PYQT is not set
# BR2_PACKAGE_LUACRYPTO is not set
# BR2_PACKAGE_TN5250 is not set
# BR2_PACKAGE_BOOST_SIGNALS is not set
# BR2_PACKAGE_FFTW_PRECISION_SINGLE is not set
# BR2_PACKAGE_FFTW_PRECISION_DOUBLE is not set
# BR2_PACKAGE_FFTW_PRECISION_LONG_DOUBLE is not set
# BR2_PACKAGE_LUA_5_2 is not set
# BR2_TARGET_GENERIC_PASSWD_MD5 is not set
#
# Legacy options removed in 2018.11
#
# BR2_TARGET_XLOADER is not set
# BR2_PACKAGE_TIDSP_BINARIES is not set
# BR2_PACKAGE_DSP_TOOLS is not set
# BR2_PACKAGE_GST_DSP is not set
# BR2_PACKAGE_BOOTUTILS is not set
# BR2_PACKAGE_EXPEDITE is not set
# BR2_PACKAGE_MESA3D_OPENGL_TEXTURE_FLOAT is not set
# BR2_KERNEL_HEADERS_4_10 is not set
# BR2_KERNEL_HEADERS_4_11 is not set
# BR2_KERNEL_HEADERS_4_12 is not set
# BR2_KERNEL_HEADERS_4_13 is not set
# BR2_KERNEL_HEADERS_4_15 is not set
# BR2_KERNEL_HEADERS_4_17 is not set
# BR2_PACKAGE_LIBNFTNL_XML is not set
# BR2_KERNEL_HEADERS_3_2 is not set
# BR2_KERNEL_HEADERS_4_1 is not set
# BR2_KERNEL_HEADERS_4_16 is not set
# BR2_KERNEL_HEADERS_4_18 is not set
#
# Legacy options removed in 2018.08
#
# BR2_PACKAGE_DOCKER_ENGINE_STATIC_CLIENT is not set
# BR2_PACKAGE_XPROTO_APPLEWMPROTO is not set
# BR2_PACKAGE_XPROTO_BIGREQSPROTO is not set
# BR2_PACKAGE_XPROTO_COMPOSITEPROTO is not set
# BR2_PACKAGE_XPROTO_DAMAGEPROTO is not set
# BR2_PACKAGE_XPROTO_DMXPROTO is not set
# BR2_PACKAGE_XPROTO_DRI2PROTO is not set
# BR2_PACKAGE_XPROTO_DRI3PROTO is not set
# BR2_PACKAGE_XPROTO_FIXESPROTO is not set
# BR2_PACKAGE_XPROTO_FONTCACHEPROTO is not set
# BR2_PACKAGE_XPROTO_FONTSPROTO is not set
# BR2_PACKAGE_XPROTO_GLPROTO is not set
# BR2_PACKAGE_XPROTO_INPUTPROTO is not set
# BR2_PACKAGE_XPROTO_KBPROTO is not set
# BR2_PACKAGE_XPROTO_PRESENTPROTO is not set
# BR2_PACKAGE_XPROTO_RANDRPROTO is not set
# BR2_PACKAGE_XPROTO_RECORDPROTO is not set
# BR2_PACKAGE_XPROTO_RENDERPROTO is not set
# BR2_PACKAGE_XPROTO_RESOURCEPROTO is not set
# BR2_PACKAGE_XPROTO_SCRNSAVERPROTO is not set
# BR2_PACKAGE_XPROTO_VIDEOPROTO is not set
# BR2_PACKAGE_XPROTO_WINDOWSWMPROTO is not set
# BR2_PACKAGE_XPROTO_XCMISCPROTO is not set
# BR2_PACKAGE_XPROTO_XEXTPROTO is not set
# BR2_PACKAGE_XPROTO_XF86BIGFONTPROTO is not set
# BR2_PACKAGE_XPROTO_XF86DGAPROTO is not set
# BR2_PACKAGE_XPROTO_XF86DRIPROTO is not set
# BR2_PACKAGE_XPROTO_XF86VIDMODEPROTO is not set
# BR2_PACKAGE_XPROTO_XINERAMAPROTO is not set
# BR2_PACKAGE_XPROTO_XPROTO is not set
# BR2_PACKAGE_XPROTO_XPROXYMANAGEMENTPROTOCOL is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_LIB_OPENGL_OPENGL is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_LIB_OPENGL_GLES2 is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_LIB_OPENGL_GLX is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_LIB_OPENGL_EGL is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_LIB_OPENGL_X11 is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_LIB_OPENGL_WAYLAND is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_LIB_OPENGL_DISPMANX is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_AUDIOMIXER is not set
# BR2_PACKAGE_GST1_PLUGINS_UGLY_PLUGIN_LAME is not set
# BR2_PACKAGE_GST1_PLUGINS_UGLY_PLUGIN_MPG123 is not set
# BR2_GDB_VERSION_7_11 is not set
# BR2_GDB_VERSION_7_10 is not set
#
# Legacy options removed in 2018.05
#
# BR2_PACKAGE_MEDIAART_BACKEND_NONE is not set
# BR2_PACKAGE_MEDIAART_BACKEND_GDK_PIXBUF is not set
# BR2_PACKAGE_MEDIAART_BACKEND_QT is not set
# BR2_PACKAGE_TI_SGX_AM335X is not set
# BR2_PACKAGE_TI_SGX_AM437X is not set
# BR2_PACKAGE_TI_SGX_AM4430 is not set
# BR2_PACKAGE_TI_SGX_AM5430 is not set
# BR2_PACKAGE_JANUS_AUDIO_BRIDGE is not set
# BR2_PACKAGE_JANUS_ECHO_TEST is not set
# BR2_PACKAGE_JANUS_RECORDPLAY is not set
# BR2_PACKAGE_JANUS_SIP_GATEWAY is not set
# BR2_PACKAGE_JANUS_STREAMING is not set
# BR2_PACKAGE_JANUS_TEXT_ROOM is not set
# BR2_PACKAGE_JANUS_VIDEO_CALL is not set
# BR2_PACKAGE_JANUS_VIDEO_ROOM is not set
# BR2_PACKAGE_JANUS_MQTT is not set
# BR2_PACKAGE_JANUS_RABBITMQ is not set
# BR2_PACKAGE_JANUS_REST is not set
# BR2_PACKAGE_JANUS_UNIX_SOCKETS is not set
# BR2_PACKAGE_JANUS_WEBSOCKETS is not set
# BR2_PACKAGE_IPSEC_SECCTX_DISABLE is not set
# BR2_PACKAGE_IPSEC_SECCTX_ENABLE is not set
# BR2_PACKAGE_IPSEC_SECCTX_KERNEL is not set
# BR2_PACKAGE_LIBTFDI_CPP is not set
# BR2_PACKAGE_JQUERY_UI_THEME_BLACK_TIE is not set
# BR2_PACKAGE_JQUERY_UI_THEME_BLITZER is not set
# BR2_PACKAGE_JQUERY_UI_THEME_CUPERTINO is not set
# BR2_PACKAGE_JQUERY_UI_THEME_DARK_HIVE is not set
# BR2_PACKAGE_JQUERY_UI_THEME_DOT_LUV is not set
# BR2_PACKAGE_JQUERY_UI_THEME_EGGPLANT is not set
# BR2_PACKAGE_JQUERY_UI_THEME_EXCITE_BIKE is not set
# BR2_PACKAGE_JQUERY_UI_THEME_FLICK is not set
# BR2_PACKAGE_JQUERY_UI_THEME_HOT_SNEAKS is not set
# BR2_PACKAGE_JQUERY_UI_THEME_HUMANITY is not set
# BR2_PACKAGE_JQUERY_UI_THEME_LE_FROG is not set
# BR2_PACKAGE_JQUERY_UI_THEME_MINT_CHOC is not set
# BR2_PACKAGE_JQUERY_UI_THEME_OVERCAST is not set
# BR2_PACKAGE_JQUERY_UI_THEME_PEPPER_GRINDER is not set
# BR2_PACKAGE_JQUERY_UI_THEME_REDMOND is not set
# BR2_PACKAGE_JQUERY_UI_THEME_SMOOTHNESS is not set
# BR2_PACKAGE_JQUERY_UI_THEME_SOUTH_STREET is not set
# BR2_PACKAGE_JQUERY_UI_THEME_START is not set
# BR2_PACKAGE_JQUERY_UI_THEME_SUNNY is not set
# BR2_PACKAGE_JQUERY_UI_THEME_SWANKY_PURSE is not set
# BR2_PACKAGE_JQUERY_UI_THEME_TRONTASTIC is not set
# BR2_PACKAGE_JQUERY_UI_THEME_UI_DARKNESS is not set
# BR2_PACKAGE_JQUERY_UI_THEME_UI_LIGHTNESS is not set
# BR2_PACKAGE_JQUERY_UI_THEME_VADER is not set
# BR2_PACKAGE_BLUEZ5_PLUGINS_HEALTH is not set
# BR2_PACKAGE_BLUEZ5_PLUGINS_MIDI is not set
# BR2_PACKAGE_BLUEZ5_PLUGINS_NFC is not set
# BR2_PACKAGE_BLUEZ5_PLUGINS_SAP is not set
# BR2_PACKAGE_BLUEZ5_PLUGINS_SIXAXIS is not set
# BR2_PACKAGE_TRANSMISSION_REMOTE is not set
# BR2_PACKAGE_LIBKCAPI_APPS is not set
# BR2_PACKAGE_MPLAYER is not set
# BR2_PACKAGE_MPLAYER_MPLAYER is not set
# BR2_PACKAGE_MPLAYER_MENCODER is not set
# BR2_PACKAGE_LIBPLAYER_MPLAYER is not set
# BR2_PACKAGE_IQVLINUX is not set
# BR2_BINFMT_FLAT_SEP_DATA is not set
# BR2_bfin is not set
# BR2_PACKAGE_KODI_ADSP_BASIC is not set
# BR2_PACKAGE_KODI_ADSP_FREESURROUND is not set
#
# Legacy options removed in 2018.02
#
# BR2_KERNEL_HEADERS_3_4 is not set
# BR2_KERNEL_HEADERS_3_10 is not set
# BR2_KERNEL_HEADERS_3_12 is not set
# BR2_BINUTILS_VERSION_2_27_X is not set
# BR2_PACKAGE_EEPROG is not set
# BR2_PACKAGE_GNUPG2_GPGV2 is not set
# BR2_PACKAGE_IMX_GPU_VIV_APITRACE is not set
# BR2_PACKAGE_IMX_GPU_VIV_G2D is not set
#
# Legacy options removed in 2017.11
#
# BR2_PACKAGE_RFKILL is not set
# BR2_PACKAGE_UTIL_LINUX_RESET is not set
# BR2_PACKAGE_POLICYCOREUTILS_AUDIT2ALLOW is not set
# BR2_PACKAGE_POLICYCOREUTILS_RESTORECOND is not set
# BR2_PACKAGE_SEPOLGEN is not set
# BR2_PACKAGE_OPENOBEX_BLUEZ is not set
# BR2_PACKAGE_OPENOBEX_LIBUSB is not set
# BR2_PACKAGE_OPENOBEX_APPS is not set
# BR2_PACKAGE_OPENOBEX_SYSLOG is not set
# BR2_PACKAGE_OPENOBEX_DUMP is not set
# BR2_PACKAGE_AICCU is not set
# BR2_PACKAGE_UTIL_LINUX_LOGIN_UTILS is not set
#
# Legacy options removed in 2017.08
#
# BR2_TARGET_GRUB is not set
# BR2_PACKAGE_SIMICSFS is not set
# BR2_BINUTILS_VERSION_2_26_X is not set
BR2_XTENSA_OVERLAY_DIR=""
BR2_XTENSA_CUSTOM_NAME=""
# BR2_PACKAGE_HOST_MKE2IMG is not set
BR2_TARGET_ROOTFS_EXT2_BLOCKS=0
BR2_TARGET_ROOTFS_EXT2_EXTRA_INODES=0
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_CDXAPARSE is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_DATAURISRC is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_DCCP is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_HDVPARSE is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_MVE is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_NUVDEMUX is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_PATCHDETECT is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_SDI is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_TTA is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_VIDEOMEASURE is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_APEXSINK is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_SDL is not set
# BR2_PACKAGE_GST1_PLUGINS_UGLY_PLUGIN_MAD is not set
# BR2_STRIP_none is not set
# BR2_PACKAGE_BEECRYPT_CPP is not set
# BR2_PACKAGE_SPICE_CLIENT is not set
# BR2_PACKAGE_SPICE_GUI is not set
# BR2_PACKAGE_SPICE_TUNNEL is not set
# BR2_PACKAGE_INPUT_TOOLS is not set
# BR2_PACKAGE_INPUT_TOOLS_INPUTATTACH is not set
# BR2_PACKAGE_INPUT_TOOLS_JSCAL is not set
# BR2_PACKAGE_INPUT_TOOLS_JSTEST is not set
# BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_SH is not set
# BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_X86 is not set
# BR2_GCC_VERSION_4_8_X is not set
#
# Legacy options removed in 2017.05
#
# BR2_PACKAGE_SUNXI_MALI_R2P4 is not set
# BR2_PACKAGE_NODEJS_MODULES_COFFEESCRIPT is not set
# BR2_PACKAGE_NODEJS_MODULES_EXPRESS is not set
# BR2_PACKAGE_BLUEZ5_UTILS_GATTTOOL is not set
# BR2_PACKAGE_OPENOCD_FT2XXX is not set
# BR2_PACKAGE_KODI_RTMPDUMP is not set
# BR2_PACKAGE_KODI_VISUALISATION_FOUNTAIN is not set
# BR2_PACKAGE_PORTMAP is not set
# BR2_BINUTILS_VERSION_2_25_X is not set
# BR2_TOOLCHAIN_BUILDROOT_INET_RPC is not set
BR2_TARGET_ROOTFS_EXT2_EXTRA_BLOCKS=0
# BR2_PACKAGE_SYSTEMD_KDBUS is not set
# BR2_PACKAGE_POLARSSL is not set
# BR2_NBD_CLIENT is not set
# BR2_NBD_SERVER is not set
# BR2_PACKAGE_GMOCK is not set
# BR2_KERNEL_HEADERS_4_8 is not set
# BR2_KERNEL_HEADERS_3_18 is not set
# BR2_GLIBC_VERSION_2_22 is not set
#
# Legacy options removed in 2017.02
#
# BR2_PACKAGE_PERL_DB_FILE is not set
# BR2_KERNEL_HEADERS_4_7 is not set
# BR2_KERNEL_HEADERS_4_6 is not set
# BR2_KERNEL_HEADERS_4_5 is not set
# BR2_KERNEL_HEADERS_3_14 is not set
# BR2_TOOLCHAIN_EXTERNAL_MUSL_CROSS is not set
# BR2_UCLIBC_INSTALL_TEST_SUITE is not set
# BR2_TOOLCHAIN_EXTERNAL_BLACKFIN_UCLINUX is not set
# BR2_PACKAGE_MAKEDEVS is not set
# BR2_TOOLCHAIN_EXTERNAL_ARAGO_ARMV7A is not set
# BR2_TOOLCHAIN_EXTERNAL_ARAGO_ARMV5TE is not set
# BR2_PACKAGE_SNOWBALL_HDMISERVICE is not set
# BR2_PACKAGE_SNOWBALL_INIT is not set
# BR2_GDB_VERSION_7_9 is not set
#
# Legacy options removed in 2016.11
#
# BR2_PACKAGE_PHP_SAPI_CLI_CGI is not set
# BR2_PACKAGE_PHP_SAPI_CLI_FPM is not set
# BR2_PACKAGE_WVSTREAMS is not set
# BR2_PACKAGE_WVDIAL is not set
# BR2_PACKAGE_WEBKITGTK24 is not set
# BR2_PACKAGE_TORSMO is not set
# BR2_PACKAGE_SSTRIP is not set
# BR2_KERNEL_HEADERS_4_3 is not set
# BR2_KERNEL_HEADERS_4_2 is not set
# BR2_PACKAGE_KODI_ADDON_XVDR is not set
# BR2_PACKAGE_IPKG is not set
# BR2_GCC_VERSION_4_7_X is not set
# BR2_BINUTILS_VERSION_2_24_X is not set
# BR2_PACKAGE_WESTON_RPI is not set
# BR2_LINUX_KERNEL_TOOL_CPUPOWER is not set
# BR2_LINUX_KERNEL_TOOL_PERF is not set
# BR2_LINUX_KERNEL_TOOL_SELFTESTS is not set
# BR2_GCC_VERSION_4_8_ARC is not set
# BR2_KERNEL_HEADERS_4_0 is not set
# BR2_KERNEL_HEADERS_3_19 is not set
# BR2_PACKAGE_LIBEVAS_GENERIC_LOADERS is not set
# BR2_PACKAGE_ELEMENTARY is not set
# BR2_LINUX_KERNEL_CUSTOM_LOCAL is not set
#
# Legacy options removed in 2016.08
#
# BR2_PACKAGE_EFL_JP2K is not set
# BR2_PACKAGE_SYSTEMD_COMPAT is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_LIVEADDER is not set
# BR2_PACKAGE_LIBFSLVPUWRAP is not set
# BR2_PACKAGE_LIBFSLPARSER is not set
# BR2_PACKAGE_LIBFSLCODEC is not set
# BR2_PACKAGE_UBOOT_TOOLS_MKIMAGE_FIT_SIGNATURE_SUPPORT is not set
# BR2_PTHREADS_OLD is not set
# BR2_BINUTILS_VERSION_2_23_X is not set
# BR2_TOOLCHAIN_BUILDROOT_EGLIBC is not set
# BR2_GDB_VERSION_7_8 is not set
#
# Legacy options removed in 2016.05
#
# BR2_PACKAGE_OPENVPN_CRYPTO_POLARSSL is not set
# BR2_PACKAGE_NGINX_HTTP_SPDY_MODULE is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_RTP is not set
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_MPG123 is not set
# BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_POWERPC is not set
# BR2_TOOLCHAIN_EXTERNAL_CODESOURCERY_POWERPC_E500V2 is not set
# BR2_x86_i386 is not set
# BR2_PACKAGE_QT5QUICK1 is not set
BR2_TARGET_UBOOT_CUSTOM_PATCH_DIR=""
# BR2_PACKAGE_XDRIVER_XF86_INPUT_VOID is not set
# BR2_KERNEL_HEADERS_3_17 is not set
# BR2_GDB_VERSION_7_7 is not set
# BR2_PACKAGE_FOOMATIC_FILTERS is not set
# BR2_PACKAGE_SAMBA is not set
# BR2_PACKAGE_KODI_WAVPACK is not set
# BR2_PACKAGE_KODI_RSXS is not set
# BR2_PACKAGE_KODI_GOOM is not set
# BR2_PACKAGE_SYSTEMD_ALL_EXTRAS is not set
# BR2_GCC_VERSION_4_5_X is not set
# BR2_PACKAGE_SQLITE_READLINE is not set
#
# Legacy options removed in 2016.02
#
# BR2_PACKAGE_DOVECOT_BZIP2 is not set
# BR2_PACKAGE_DOVECOT_ZLIB is not set
# BR2_PACKAGE_E2FSPROGS_FINDFS is not set
# BR2_PACKAGE_OPENPOWERLINK_DEBUG_LEVEL is not set
# BR2_PACKAGE_OPENPOWERLINK_KERNEL_MODULE is not set
# BR2_PACKAGE_OPENPOWERLINK_LIBPCAP is not set
# BR2_LINUX_KERNEL_SAME_AS_HEADERS is not set
# BR2_PACKAGE_CUPS_PDFTOPS is not set
# BR2_KERNEL_HEADERS_3_16 is not set
# BR2_PACKAGE_PYTHON_PYXML is not set
# BR2_ENABLE_SSP is not set
# BR2_PACKAGE_DIRECTFB_CLE266 is not set
# BR2_PACKAGE_DIRECTFB_UNICHROME is not set
# BR2_PACKAGE_LIBELEMENTARY is not set
# BR2_PACKAGE_LIBEINA is not set
# BR2_PACKAGE_LIBEET is not set
# BR2_PACKAGE_LIBEVAS is not set
# BR2_PACKAGE_LIBECORE is not set
# BR2_PACKAGE_LIBEDBUS is not set
# BR2_PACKAGE_LIBEFREET is not set
# BR2_PACKAGE_LIBEIO is not set
# BR2_PACKAGE_LIBEMBRYO is not set
# BR2_PACKAGE_LIBEDJE is not set
# BR2_PACKAGE_LIBETHUMB is not set
# BR2_PACKAGE_INFOZIP is not set
# BR2_BR2_PACKAGE_NODEJS_0_10_X is not set
# BR2_BR2_PACKAGE_NODEJS_0_12_X is not set
# BR2_BR2_PACKAGE_NODEJS_4_X is not set
#
# Legacy options removed in 2015.11
#
# BR2_PACKAGE_GST1_PLUGINS_BAD_PLUGIN_REAL is not set
# BR2_PACKAGE_MEDIA_CTL is not set
# BR2_PACKAGE_SCHIFRA is not set
# BR2_PACKAGE_ZXING is not set
# BR2_PACKAGE_BLACKBOX is not set
# BR2_KERNEL_HEADERS_3_0 is not set
# BR2_KERNEL_HEADERS_3_11 is not set
# BR2_KERNEL_HEADERS_3_13 is not set
# BR2_KERNEL_HEADERS_3_15 is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_ANDI is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_BLTLOAD is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_CPULOAD is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_DATABUFFER is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_DIOLOAD is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_DOK is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_DRIVERTEST is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_FIRE is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_FLIP is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_FONTS is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_INPUT is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_JOYSTICK is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_KNUCKLES is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_LAYER is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_MATRIX is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_MATRIX_WATER is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_NEO is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_NETLOAD is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_PALETTE is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_PARTICLE is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_PORTER is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_STRESS is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_TEXTURE is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_VIDEO is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_VIDEO_PARTICLE is not set
# BR2_PACKAGE_DIRECTFB_EXAMPLES_WINDOW is not set
# BR2_PACKAGE_KOBS_NG is not set
# BR2_PACKAGE_SAWMAN is not set
# BR2_PACKAGE_DIVINE is not set
#
# Legacy options removed in 2015.08
#
# BR2_PACKAGE_KODI_PVR_ADDONS is not set
# BR2_BINUTILS_VERSION_2_23_2 is not set
# BR2_BINUTILS_VERSION_2_24 is not set
# BR2_BINUTILS_VERSION_2_25 is not set
# BR2_PACKAGE_PERF is not set
# BR2_BINUTILS_VERSION_2_22 is not set
# BR2_PACKAGE_GPU_VIV_BIN_MX6Q is not set
# BR2_TARGET_UBOOT_NETWORK is not set
[-- Attachment #3: Type: text/plain, Size: 150 bytes --]
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-23 20:53 ` Neil Webster
@ 2024-09-24 2:58 ` Neil Webster
2024-09-24 6:23 ` Arnout Vandecappelle via buildroot
1 sibling, 0 replies; 15+ messages in thread
From: Neil Webster @ 2024-09-24 2:58 UTC (permalink / raw)
To: Arnout Vandecappelle, buildroot@buildroot.org
Hi Arnout,
Been digging a bit more. It seems that I have an issue with my
definition of the URL for the kernel tarball. The path I have defined
has multiple possibilities. I will do some more research on this.
Cheers, Neil
On 2024-09-23 4:53 p.m., Neil Webster wrote:
> Hi Arnout,
>
> Thanks for the quick response.
>
> I looked through the yocto build directory and it seems that they are
> using 6.1.1-1.0.0 for all of the below.
>
> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION
>
> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION
>
> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION
>
> So I changed them (.config attached).
>
> The build failed with the following ...
>
> ERROR: No hash found for linux-imx-lf-6.1.1-1.0.0.tar.gz
> make[1]: *** [package/pkg-generic.mk:179:
> /home/neil/buildroot-2024.08/output/build/linux-headers-custom/.stamp_downloaded]
> Error 1
>
> Thoughts on next steps appreciated.
>
> Thanks for your patience in working through this with a newbie.
>
> Cheers, Neil
>
> On 2024-09-23 3:36 p.m., Arnout Vandecappelle wrote:
>>
>>
>> On 23/09/2024 21:30, Neil Webster wrote:
>>> Hi Arnout,
>>>
>>> Thank you for the response.
>>>
>>> I will work through each of your suggestions and I started with the
>>> one that you stated was definitely incorrect i.e. The DTS name.
>>>
>>> The Variscite device trees are described here
>>>
>>> https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
>>>
>>>
>>> I found and copied three DTS(I) files
>>>
>>> imx8mm-var-dart-dt8mcustomboard.dts
>>>
>>> which #includes ...
>>>
>>> imx8mm-var-dart.dtsi
>>>
>>> which #includes ...
>>>
>>> imx8mm.dtsi
>>
>> This one, at least, should be in the kernel source itself. If you're
>> using a kernel that doesn't already have imx8mm.dtsi, it's probably
>> going to be wildly incompatible with Variscite's device tree.
>>
>>
>>> I referenced the location of these files in
>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH and I see it copies them to
>>> output/build/linux-custom/arch/arm64/boot/dts/
>>>
>>> The subsequent build complained about missing dependencies and I
>>> also had to add imx8mm-pinfunc.h and mxl-8611x.h to
>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is that
>>
>> Again, these should normally be part of the kernel already.
>>
>>> the correct way to add .h dependencies or is there a cleaner way or
>>> doing this i.e. should the BR2_LINUX_KERNEL_CUSTOM_DTS_PATH be
>>> reserved for DTS files only as the name suggests?
>>
>> Not really - the header files are shared between device tree and
>> corresponding drivers. So they should already be part of the kernel
>> source. If they are not, it's quite likely that things are not going
>> to work.
>>
>> There may be situations where it makes sense to add header files to
>> CUSTOM_DTS_PATH, but that's squarely You Must Know What You're Doing
>> territory...
>>
>>
>>>
>>> Anyway the build succeeded after adding those .h files but sadly
>>> still no console. I will now move onto looking at the other items
>>> you mentioned.
>>
>> Well, I'd start with concentrating on getting output from TF-A and
>> U-Boot. Right now you don't even know if the kernel is loaded!
>>
>>
>> Regards,
>> Arnout
>>
>>
>>>
>>> Cheers, Neil
>>>
>>> On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
>>>> [You don't often get email from arnout@mind.be. Learn why this is
>>>> important at https://aka.ms/LearnAboutSenderIdentification ]
>>>>
>>>> Hi Neil,
>>>>
>>>> On 19/09/2024 00:19, Neil Webster wrote:
>>>>> Hello,
>>>>>
>>>>> I am new to Buildroot and have been struggling for a couple of
>>>>> days with
>>>>> something and wondering if I could get some pointers. Please let
>>>>> me know
>>>>> if this is not the appropriate place to post such questions.
>>>>>
>>>>> I want to get an embedded Linux image running on a Variscite Dart
>>>>> Mini
>>>>> (link below)
>>>>>
>>>>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/dart-
>>>>> mx8m-mini-nxp-i-mx8m-mini/
>>>>>
>>>>> I have the SOM connected to a dev kit referenced in the same link
>>>>> above.
>>>>>
>>>>> I wanted to use the opportunity to get familiar with Buildroot but
>>>>> sadly
>>>>> Variscite do not support Buildroot and instead they steered me
>>>>> towards
>>>>> Yocto.
>>>>
>>>> :sad-face:
>>>>
>>>>
>>>>> I have been able to get an image running with Yocto following their
>>>>> recipes but I found the whole process to be obscure and opaque and
>>>>> I am
>>>>> therefore back to my original objective of using Buildroot.
>>>>
>>>> Please make sure to give this feedback to Variscite!
>>>>
>>>>
>>>>>
>>>>> I have been able to follow the tutorials and get a build working on a
>>>>> Raspberry Pi.
>>>>>
>>>>> However, as mentioned above there is no support available from
>>>>> Variscite
>>>>> and there is no specific defconfig for my hardware, so I tried to
>>>>> start
>>>>> with freescale_imx8mmevk_defconfig as this seems to be close with
>>>>> what
>>>>> appear to be correct settings under the "target options" menu.
>>>>
>>>> Yes, that's an excellent start!
>>>>
>>>> ... but not enough to get a working board...
>>>>
>>>>
>>>>> However I am not getting anything at the console.
>>>>>
>>>>> I noticed that the freescale_imx8mmevk_defconfig sets the getty
>>>>> TTY port
>>>>> to ttymxc1, so I tried changing this to ttymxc0 as that is the port
>>>>> mapped to the debug interface on the development board. Still
>>>>> nothing at
>>>>> the console.
>>>>
>>>> That is one of the things you need to change indeed. However,
>>>> things already
>>>> went wrong way before that, because you should have gotten U-Boot
>>>> and kernel
>>>> debug output on the console.
>>>>
>>>> There are a number of things you have to change in a defconfig
>>>> when you switch
>>>> to a different (but similar) board. I'm going to list them below
>>>> with the symbol
>>>> names, not how they appear in the menu. You can always search for
>>>> those symbols
>>>> in `make menuconfig` by typing /
>>>>
>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
>>>> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>>>>
>>>>
>>>> You should check Variscite's yocto layer to see if they use the NXP
>>>> TF-A or if
>>>> they fork it even more. They may also use a different version.
>>>>
>>>>
>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>>>>
>>>> I expect that this will be OK for the Variscite board as well, but
>>>> it is
>>>> possible that they have defined their own platform.
>>>>
>>>>
>>>>
>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
>>>> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>
>>>>
>>>> You should check Variscite's yocto layer to see if they use the NXP
>>>> U-Boot or if
>>>> they fork it even more. They may also use a different version.
>>>>
>>>>
>>>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>>>>
>>>> This needs to change to the U-Boot defconfig. That defconfig could
>>>> be in NXP's
>>>> U-Boot fork already, or it could be in Variscite's fork, or
>>>> Variscite may supply
>>>> it in their u-boot yocto recipe.
>>>>
>>>>
>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
>>>> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>
>>>> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
>>>> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
>>>> freescale/imx8mm-evk-revb-qca-wifi"
>>>>
>>>> You probably start to know the drill, right? The defconfig is
>>>> probably OK,
>>>> although it's possible that Variscite appends a fragment to it in
>>>> their
>>>> bbappend. The DTS name is most definitely not OK, but it might come
>>>> from
>>>> Variscite's metalayer instead of NXP's kernel. The kernel is
>>>> unlikely to be
>>>> forked by Variscite so that one is probably OK, but it may be a
>>>> different version.
>>>>
>>>>
>>>>> I tried changing the init system from busybox to systemd. Still
>>>>> nothing.
>>>>
>>>> No, busybox init should work fine.
>>>>
>>>>
>>>>> I feel like I am poking around in the dark. Any thoughts on what I
>>>>> should try next?
>>>>
>>>> If you do manage to advance with this, there are two contributions
>>>> you could make:
>>>> - You can add a defconfig for the Variscite board.
>>>> - You could update the documentation with a "how to add support for
>>>> a new board"
>>>> section that explains what I wrote above in a better (more generic)
>>>> way.
>>>>
>>>>
>>>> Regards,
>>>> Arnout
>>>>
>>
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-23 20:53 ` Neil Webster
2024-09-24 2:58 ` Neil Webster
@ 2024-09-24 6:23 ` Arnout Vandecappelle via buildroot
2024-09-24 15:24 ` Neil Webster
1 sibling, 1 reply; 15+ messages in thread
From: Arnout Vandecappelle via buildroot @ 2024-09-24 6:23 UTC (permalink / raw)
To: Neil Webster, buildroot@buildroot.org
On 23/09/2024 22:53, Neil Webster wrote:
> Hi Arnout,
>
> Thanks for the quick response.
>
> I looked through the yocto build directory and it seems that they are using
> 6.1.1-1.0.0 for all of the below.
>
> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION
>
> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION
>
> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION
>
> So I changed them (.config attached).
>
> The build failed with the following ...
>
> ERROR: No hash found for linux-imx-lf-6.1.1-1.0.0.tar.gz
> make[1]: *** [package/pkg-generic.mk:179: /home/neil/buildroot-2024.08/output/
> build/linux-headers-custom/.stamp_downloaded] Error 1
You probably have BR2_DOWNLOAD_FORCE_CHECK_HASHES=y turned on because you
started from a defconfig that has a hash file. Either disable this option, or
update board/freescale/imx8mmevk/patches/linux/linux.hash with the hash of the
tarball.
Regards,
Arnout
>
> Thoughts on next steps appreciated.
>
> Thanks for your patience in working through this with a newbie.
>
> Cheers, Neil
>
> On 2024-09-23 3:36 p.m., Arnout Vandecappelle wrote:
>>
>>
>> On 23/09/2024 21:30, Neil Webster wrote:
>>> Hi Arnout,
>>>
>>> Thank you for the response.
>>>
>>> I will work through each of your suggestions and I started with the one that
>>> you stated was definitely incorrect i.e. The DTS name.
>>>
>>> The Variscite device trees are described here
>>>
>>> https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
>>>
>>> I found and copied three DTS(I) files
>>>
>>> imx8mm-var-dart-dt8mcustomboard.dts
>>>
>>> which #includes ...
>>>
>>> imx8mm-var-dart.dtsi
>>>
>>> which #includes ...
>>>
>>> imx8mm.dtsi
>>
>> This one, at least, should be in the kernel source itself. If you're using a
>> kernel that doesn't already have imx8mm.dtsi, it's probably going to be wildly
>> incompatible with Variscite's device tree.
>>
>>
>>> I referenced the location of these files in BR2_LINUX_KERNEL_CUSTOM_DTS_PATH
>>> and I see it copies them to output/build/linux-custom/arch/arm64/boot/dts/
>>>
>>> The subsequent build complained about missing dependencies and I also had to
>>> add imx8mm-pinfunc.h and mxl-8611x.h to BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is
>>> that
>>
>> Again, these should normally be part of the kernel already.
>>
>>> the correct way to add .h dependencies or is there a cleaner way or doing
>>> this i.e. should the BR2_LINUX_KERNEL_CUSTOM_DTS_PATH be reserved for DTS
>>> files only as the name suggests?
>>
>> Not really - the header files are shared between device tree and
>> corresponding drivers. So they should already be part of the kernel source. If
>> they are not, it's quite likely that things are not going to work.
>>
>> There may be situations where it makes sense to add header files to
>> CUSTOM_DTS_PATH, but that's squarely You Must Know What You're Doing territory...
>>
>>
>>>
>>> Anyway the build succeeded after adding those .h files but sadly still no
>>> console. I will now move onto looking at the other items you mentioned.
>>
>> Well, I'd start with concentrating on getting output from TF-A and U-Boot.
>> Right now you don't even know if the kernel is loaded!
>>
>>
>> Regards,
>> Arnout
>>
>>
>>>
>>> Cheers, Neil
>>>
>>> On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
>>>> [You don't often get email from arnout@mind.be. Learn why this is important
>>>> at https://aka.ms/LearnAboutSenderIdentification ]
>>>>
>>>> Hi Neil,
>>>>
>>>> On 19/09/2024 00:19, Neil Webster wrote:
>>>>> Hello,
>>>>>
>>>>> I am new to Buildroot and have been struggling for a couple of days with
>>>>> something and wondering if I could get some pointers. Please let me know
>>>>> if this is not the appropriate place to post such questions.
>>>>>
>>>>> I want to get an embedded Linux image running on a Variscite Dart Mini
>>>>> (link below)
>>>>>
>>>>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/
>>>>> dart- mx8m-mini-nxp-i-mx8m-mini/
>>>>>
>>>>> I have the SOM connected to a dev kit referenced in the same link above.
>>>>>
>>>>> I wanted to use the opportunity to get familiar with Buildroot but sadly
>>>>> Variscite do not support Buildroot and instead they steered me towards
>>>>> Yocto.
>>>>
>>>> :sad-face:
>>>>
>>>>
>>>>> I have been able to get an image running with Yocto following their
>>>>> recipes but I found the whole process to be obscure and opaque and I am
>>>>> therefore back to my original objective of using Buildroot.
>>>>
>>>> Please make sure to give this feedback to Variscite!
>>>>
>>>>
>>>>>
>>>>> I have been able to follow the tutorials and get a build working on a
>>>>> Raspberry Pi.
>>>>>
>>>>> However, as mentioned above there is no support available from Variscite
>>>>> and there is no specific defconfig for my hardware, so I tried to start
>>>>> with freescale_imx8mmevk_defconfig as this seems to be close with what
>>>>> appear to be correct settings under the "target options" menu.
>>>>
>>>> Yes, that's an excellent start!
>>>>
>>>> ... but not enough to get a working board...
>>>>
>>>>
>>>>> However I am not getting anything at the console.
>>>>>
>>>>> I noticed that the freescale_imx8mmevk_defconfig sets the getty TTY port
>>>>> to ttymxc1, so I tried changing this to ttymxc0 as that is the port
>>>>> mapped to the debug interface on the development board. Still nothing at
>>>>> the console.
>>>>
>>>> That is one of the things you need to change indeed. However, things already
>>>> went wrong way before that, because you should have gotten U-Boot and kernel
>>>> debug output on the console.
>>>>
>>>> There are a number of things you have to change in a defconfig when you switch
>>>> to a different (but similar) board. I'm going to list them below with the
>>>> symbol
>>>> names, not how they appear in the menu. You can always search for those symbols
>>>> in `make menuconfig` by typing /
>>>>
>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
>>>> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>>>>
>>>> You should check Variscite's yocto layer to see if they use the NXP TF-A or if
>>>> they fork it even more. They may also use a different version.
>>>>
>>>>
>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>>>>
>>>> I expect that this will be OK for the Variscite board as well, but it is
>>>> possible that they have defined their own platform.
>>>>
>>>>
>>>>
>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
>>>> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>
>>>> You should check Variscite's yocto layer to see if they use the NXP U-Boot
>>>> or if
>>>> they fork it even more. They may also use a different version.
>>>>
>>>>
>>>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>>>>
>>>> This needs to change to the U-Boot defconfig. That defconfig could be in NXP's
>>>> U-Boot fork already, or it could be in Variscite's fork, or Variscite may
>>>> supply
>>>> it in their u-boot yocto recipe.
>>>>
>>>>
>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
>>>> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>>>> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
>>>> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
>>>> freescale/imx8mm-evk-revb-qca-wifi"
>>>>
>>>> You probably start to know the drill, right? The defconfig is probably OK,
>>>> although it's possible that Variscite appends a fragment to it in their
>>>> bbappend. The DTS name is most definitely not OK, but it might come from
>>>> Variscite's metalayer instead of NXP's kernel. The kernel is unlikely to be
>>>> forked by Variscite so that one is probably OK, but it may be a different
>>>> version.
>>>>
>>>>
>>>>> I tried changing the init system from busybox to systemd. Still nothing.
>>>>
>>>> No, busybox init should work fine.
>>>>
>>>>
>>>>> I feel like I am poking around in the dark. Any thoughts on what I
>>>>> should try next?
>>>>
>>>> If you do manage to advance with this, there are two contributions you
>>>> could make:
>>>> - You can add a defconfig for the Variscite board.
>>>> - You could update the documentation with a "how to add support for a new
>>>> board"
>>>> section that explains what I wrote above in a better (more generic) way.
>>>>
>>>>
>>>> Regards,
>>>> Arnout
>>>>
>>
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-24 6:23 ` Arnout Vandecappelle via buildroot
@ 2024-09-24 15:24 ` Neil Webster
2024-09-24 16:04 ` Arnout Vandecappelle via buildroot
0 siblings, 1 reply; 15+ messages in thread
From: Neil Webster @ 2024-09-24 15:24 UTC (permalink / raw)
To: Arnout Vandecappelle, buildroot@buildroot.org
Hi Arnout,
I was using an incorrect version and the url was not correct.
The Yocto build uses 6.1.36-2.1.0 and I changed the three tarballs to
that. I also disabled the hash checking as per your previous comment.
The download now works but I hit this error ...
INSTALL
/home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-gnu/sysroot/usr/include
if ! support/scripts/check-kernel-headers.sh
/home/neil/buildroot-2024.08/output/build
/home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-gnu/sysroot
6.6 strict; then exit 1; fi
Incorrect selection of kernel headers: expected 6.6.x, got 6.1.x
Regards, Neil
On 2024-09-24 2:23 a.m., Arnout Vandecappelle wrote:
>
>
> On 23/09/2024 22:53, Neil Webster wrote:
>> Hi Arnout,
>>
>> Thanks for the quick response.
>>
>> I looked through the yocto build directory and it seems that they are
>> using 6.1.1-1.0.0 for all of the below.
>>
>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION
>>
>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION
>>
>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION
>>
>> So I changed them (.config attached).
>>
>> The build failed with the following ...
>>
>> ERROR: No hash found for linux-imx-lf-6.1.1-1.0.0.tar.gz
>> make[1]: *** [package/pkg-generic.mk:179:
>> /home/neil/buildroot-2024.08/output/
>> build/linux-headers-custom/.stamp_downloaded] Error 1
>
> You probably have BR2_DOWNLOAD_FORCE_CHECK_HASHES=y turned on because
> you started from a defconfig that has a hash file. Either disable this
> option, or update board/freescale/imx8mmevk/patches/linux/linux.hash
> with the hash of the tarball.
>
> Regards,
> Arnout
>
>>
>> Thoughts on next steps appreciated.
>>
>> Thanks for your patience in working through this with a newbie.
>>
>> Cheers, Neil
>>
>> On 2024-09-23 3:36 p.m., Arnout Vandecappelle wrote:
>>>
>>>
>>> On 23/09/2024 21:30, Neil Webster wrote:
>>>> Hi Arnout,
>>>>
>>>> Thank you for the response.
>>>>
>>>> I will work through each of your suggestions and I started with the
>>>> one that you stated was definitely incorrect i.e. The DTS name.
>>>>
>>>> The Variscite device trees are described here
>>>>
>>>> https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
>>>>
>>>>
>>>> I found and copied three DTS(I) files
>>>>
>>>> imx8mm-var-dart-dt8mcustomboard.dts
>>>>
>>>> which #includes ...
>>>>
>>>> imx8mm-var-dart.dtsi
>>>>
>>>> which #includes ...
>>>>
>>>> imx8mm.dtsi
>>>
>>> This one, at least, should be in the kernel source itself. If
>>> you're using a kernel that doesn't already have imx8mm.dtsi, it's
>>> probably going to be wildly incompatible with Variscite's device tree.
>>>
>>>
>>>> I referenced the location of these files in
>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH and I see it copies them to
>>>> output/build/linux-custom/arch/arm64/boot/dts/
>>>>
>>>> The subsequent build complained about missing dependencies and I
>>>> also had to add imx8mm-pinfunc.h and mxl-8611x.h to
>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is that
>>>
>>> Again, these should normally be part of the kernel already.
>>>
>>>> the correct way to add .h dependencies or is there a cleaner way or
>>>> doing this i.e. should the BR2_LINUX_KERNEL_CUSTOM_DTS_PATH be
>>>> reserved for DTS files only as the name suggests?
>>>
>>> Not really - the header files are shared between device tree and
>>> corresponding drivers. So they should already be part of the kernel
>>> source. If they are not, it's quite likely that things are not going
>>> to work.
>>>
>>> There may be situations where it makes sense to add header files to
>>> CUSTOM_DTS_PATH, but that's squarely You Must Know What You're Doing
>>> territory...
>>>
>>>
>>>>
>>>> Anyway the build succeeded after adding those .h files but sadly
>>>> still no console. I will now move onto looking at the other items
>>>> you mentioned.
>>>
>>> Well, I'd start with concentrating on getting output from TF-A and
>>> U-Boot. Right now you don't even know if the kernel is loaded!
>>>
>>>
>>> Regards,
>>> Arnout
>>>
>>>
>>>>
>>>> Cheers, Neil
>>>>
>>>> On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
>>>>> [You don't often get email from arnout@mind.be. Learn why this is
>>>>> important at https://aka.ms/LearnAboutSenderIdentification ]
>>>>>
>>>>> Hi Neil,
>>>>>
>>>>> On 19/09/2024 00:19, Neil Webster wrote:
>>>>>> Hello,
>>>>>>
>>>>>> I am new to Buildroot and have been struggling for a couple of
>>>>>> days with
>>>>>> something and wondering if I could get some pointers. Please let
>>>>>> me know
>>>>>> if this is not the appropriate place to post such questions.
>>>>>>
>>>>>> I want to get an embedded Linux image running on a Variscite Dart
>>>>>> Mini
>>>>>> (link below)
>>>>>>
>>>>>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/
>>>>>> dart- mx8m-mini-nxp-i-mx8m-mini/
>>>>>>
>>>>>> I have the SOM connected to a dev kit referenced in the same link
>>>>>> above.
>>>>>>
>>>>>> I wanted to use the opportunity to get familiar with Buildroot
>>>>>> but sadly
>>>>>> Variscite do not support Buildroot and instead they steered me
>>>>>> towards
>>>>>> Yocto.
>>>>>
>>>>> :sad-face:
>>>>>
>>>>>
>>>>>> I have been able to get an image running with Yocto following their
>>>>>> recipes but I found the whole process to be obscure and opaque
>>>>>> and I am
>>>>>> therefore back to my original objective of using Buildroot.
>>>>>
>>>>> Please make sure to give this feedback to Variscite!
>>>>>
>>>>>
>>>>>>
>>>>>> I have been able to follow the tutorials and get a build working
>>>>>> on a
>>>>>> Raspberry Pi.
>>>>>>
>>>>>> However, as mentioned above there is no support available from
>>>>>> Variscite
>>>>>> and there is no specific defconfig for my hardware, so I tried to
>>>>>> start
>>>>>> with freescale_imx8mmevk_defconfig as this seems to be close with
>>>>>> what
>>>>>> appear to be correct settings under the "target options" menu.
>>>>>
>>>>> Yes, that's an excellent start!
>>>>>
>>>>> ... but not enough to get a working board...
>>>>>
>>>>>
>>>>>> However I am not getting anything at the console.
>>>>>>
>>>>>> I noticed that the freescale_imx8mmevk_defconfig sets the getty
>>>>>> TTY port
>>>>>> to ttymxc1, so I tried changing this to ttymxc0 as that is the port
>>>>>> mapped to the debug interface on the development board. Still
>>>>>> nothing at
>>>>>> the console.
>>>>>
>>>>> That is one of the things you need to change indeed. However,
>>>>> things already
>>>>> went wrong way before that, because you should have gotten U-Boot
>>>>> and kernel
>>>>> debug output on the console.
>>>>>
>>>>> There are a number of things you have to change in a defconfig
>>>>> when you switch
>>>>> to a different (but similar) board. I'm going to list them below
>>>>> with the symbol
>>>>> names, not how they appear in the menu. You can always search for
>>>>> those symbols
>>>>> in `make menuconfig` by typing /
>>>>>
>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
>>>>> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>>>>>
>>>>>
>>>>> You should check Variscite's yocto layer to see if they use the
>>>>> NXP TF-A or if
>>>>> they fork it even more. They may also use a different version.
>>>>>
>>>>>
>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>>>>>
>>>>> I expect that this will be OK for the Variscite board as well, but
>>>>> it is
>>>>> possible that they have defined their own platform.
>>>>>
>>>>>
>>>>>
>>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
>>>>> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>
>>>>>
>>>>> You should check Variscite's yocto layer to see if they use the
>>>>> NXP U-Boot or if
>>>>> they fork it even more. They may also use a different version.
>>>>>
>>>>>
>>>>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>>>>>
>>>>> This needs to change to the U-Boot defconfig. That defconfig could
>>>>> be in NXP's
>>>>> U-Boot fork already, or it could be in Variscite's fork, or
>>>>> Variscite may supply
>>>>> it in their u-boot yocto recipe.
>>>>>
>>>>>
>>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
>>>>> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>
>>>>> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
>>>>> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
>>>>> freescale/imx8mm-evk-revb-qca-wifi"
>>>>>
>>>>> You probably start to know the drill, right? The defconfig is
>>>>> probably OK,
>>>>> although it's possible that Variscite appends a fragment to it in
>>>>> their
>>>>> bbappend. The DTS name is most definitely not OK, but it might
>>>>> come from
>>>>> Variscite's metalayer instead of NXP's kernel. The kernel is
>>>>> unlikely to be
>>>>> forked by Variscite so that one is probably OK, but it may be a
>>>>> different version.
>>>>>
>>>>>
>>>>>> I tried changing the init system from busybox to systemd. Still
>>>>>> nothing.
>>>>>
>>>>> No, busybox init should work fine.
>>>>>
>>>>>
>>>>>> I feel like I am poking around in the dark. Any thoughts on what I
>>>>>> should try next?
>>>>>
>>>>> If you do manage to advance with this, there are two
>>>>> contributions you could make:
>>>>> - You can add a defconfig for the Variscite board.
>>>>> - You could update the documentation with a "how to add support
>>>>> for a new board"
>>>>> section that explains what I wrote above in a better (more
>>>>> generic) way.
>>>>>
>>>>>
>>>>> Regards,
>>>>> Arnout
>>>>>
>>>
>
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-24 15:24 ` Neil Webster
@ 2024-09-24 16:04 ` Arnout Vandecappelle via buildroot
2024-09-24 16:11 ` Neil Webster
0 siblings, 1 reply; 15+ messages in thread
From: Arnout Vandecappelle via buildroot @ 2024-09-24 16:04 UTC (permalink / raw)
To: Neil Webster, buildroot@buildroot.org
On 24/09/2024 17:24, Neil Webster wrote:
> Hi Arnout,
>
> I was using an incorrect version and the url was not correct.
>
> The Yocto build uses 6.1.36-2.1.0 and I changed the three tarballs to that. I
> also disabled the hash checking as per your previous comment. The download now
> works but I hit this error ...
>
> INSTALL /home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-gnu/
> sysroot/usr/include
> if ! support/scripts/check-kernel-headers.sh /home/neil/buildroot-2024.08/
> output/build /home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-
> gnu/sysroot 6.6 strict; then exit 1; fi
> Incorrect selection of kernel headers: expected 6.6.x, got 6.1.x
As it says: you have to change the kernel headers version to 6.1.x.
But it's probably better to just switch to an external (Bootlin) toolchain.
We're going to make that the default for the defconfigs in the future.
Regards,
Arnout
>
> Regards, Neil
>
>
> On 2024-09-24 2:23 a.m., Arnout Vandecappelle wrote:
>>
>>
>> On 23/09/2024 22:53, Neil Webster wrote:
>>> Hi Arnout,
>>>
>>> Thanks for the quick response.
>>>
>>> I looked through the yocto build directory and it seems that they are using
>>> 6.1.1-1.0.0 for all of the below.
>>>
>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION
>>>
>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION
>>>
>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION
>>>
>>> So I changed them (.config attached).
>>>
>>> The build failed with the following ...
>>>
>>> ERROR: No hash found for linux-imx-lf-6.1.1-1.0.0.tar.gz
>>> make[1]: *** [package/pkg-generic.mk:179: /home/neil/buildroot-2024.08/
>>> output/ build/linux-headers-custom/.stamp_downloaded] Error 1
>>
>> You probably have BR2_DOWNLOAD_FORCE_CHECK_HASHES=y turned on because you
>> started from a defconfig that has a hash file. Either disable this option, or
>> update board/freescale/imx8mmevk/patches/linux/linux.hash with the hash of the
>> tarball.
>>
>> Regards,
>> Arnout
>>
>>>
>>> Thoughts on next steps appreciated.
>>>
>>> Thanks for your patience in working through this with a newbie.
>>>
>>> Cheers, Neil
>>>
>>> On 2024-09-23 3:36 p.m., Arnout Vandecappelle wrote:
>>>>
>>>>
>>>> On 23/09/2024 21:30, Neil Webster wrote:
>>>>> Hi Arnout,
>>>>>
>>>>> Thank you for the response.
>>>>>
>>>>> I will work through each of your suggestions and I started with the one
>>>>> that you stated was definitely incorrect i.e. The DTS name.
>>>>>
>>>>> The Variscite device trees are described here
>>>>>
>>>>> https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
>>>>>
>>>>> I found and copied three DTS(I) files
>>>>>
>>>>> imx8mm-var-dart-dt8mcustomboard.dts
>>>>>
>>>>> which #includes ...
>>>>>
>>>>> imx8mm-var-dart.dtsi
>>>>>
>>>>> which #includes ...
>>>>>
>>>>> imx8mm.dtsi
>>>>
>>>> This one, at least, should be in the kernel source itself. If you're using
>>>> a kernel that doesn't already have imx8mm.dtsi, it's probably going to be
>>>> wildly incompatible with Variscite's device tree.
>>>>
>>>>
>>>>> I referenced the location of these files in
>>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH and I see it copies them to output/build/
>>>>> linux-custom/arch/arm64/boot/dts/
>>>>>
>>>>> The subsequent build complained about missing dependencies and I also had
>>>>> to add imx8mm-pinfunc.h and mxl-8611x.h to
>>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is that
>>>>
>>>> Again, these should normally be part of the kernel already.
>>>>
>>>>> the correct way to add .h dependencies or is there a cleaner way or doing
>>>>> this i.e. should the BR2_LINUX_KERNEL_CUSTOM_DTS_PATH be reserved for DTS
>>>>> files only as the name suggests?
>>>>
>>>> Not really - the header files are shared between device tree and
>>>> corresponding drivers. So they should already be part of the kernel source.
>>>> If they are not, it's quite likely that things are not going to work.
>>>>
>>>> There may be situations where it makes sense to add header files to
>>>> CUSTOM_DTS_PATH, but that's squarely You Must Know What You're Doing
>>>> territory...
>>>>
>>>>
>>>>>
>>>>> Anyway the build succeeded after adding those .h files but sadly still no
>>>>> console. I will now move onto looking at the other items you mentioned.
>>>>
>>>> Well, I'd start with concentrating on getting output from TF-A and U-Boot.
>>>> Right now you don't even know if the kernel is loaded!
>>>>
>>>>
>>>> Regards,
>>>> Arnout
>>>>
>>>>
>>>>>
>>>>> Cheers, Neil
>>>>>
>>>>> On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
>>>>>> [You don't often get email from arnout@mind.be. Learn why this is
>>>>>> important at https://aka.ms/LearnAboutSenderIdentification ]
>>>>>>
>>>>>> Hi Neil,
>>>>>>
>>>>>> On 19/09/2024 00:19, Neil Webster wrote:
>>>>>>> Hello,
>>>>>>>
>>>>>>> I am new to Buildroot and have been struggling for a couple of days with
>>>>>>> something and wondering if I could get some pointers. Please let me know
>>>>>>> if this is not the appropriate place to post such questions.
>>>>>>>
>>>>>>> I want to get an embedded Linux image running on a Variscite Dart Mini
>>>>>>> (link below)
>>>>>>>
>>>>>>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/
>>>>>>> dart- mx8m-mini-nxp-i-mx8m-mini/
>>>>>>>
>>>>>>> I have the SOM connected to a dev kit referenced in the same link above.
>>>>>>>
>>>>>>> I wanted to use the opportunity to get familiar with Buildroot but sadly
>>>>>>> Variscite do not support Buildroot and instead they steered me towards
>>>>>>> Yocto.
>>>>>>
>>>>>> :sad-face:
>>>>>>
>>>>>>
>>>>>>> I have been able to get an image running with Yocto following their
>>>>>>> recipes but I found the whole process to be obscure and opaque and I am
>>>>>>> therefore back to my original objective of using Buildroot.
>>>>>>
>>>>>> Please make sure to give this feedback to Variscite!
>>>>>>
>>>>>>
>>>>>>>
>>>>>>> I have been able to follow the tutorials and get a build working on a
>>>>>>> Raspberry Pi.
>>>>>>>
>>>>>>> However, as mentioned above there is no support available from Variscite
>>>>>>> and there is no specific defconfig for my hardware, so I tried to start
>>>>>>> with freescale_imx8mmevk_defconfig as this seems to be close with what
>>>>>>> appear to be correct settings under the "target options" menu.
>>>>>>
>>>>>> Yes, that's an excellent start!
>>>>>>
>>>>>> ... but not enough to get a working board...
>>>>>>
>>>>>>
>>>>>>> However I am not getting anything at the console.
>>>>>>>
>>>>>>> I noticed that the freescale_imx8mmevk_defconfig sets the getty TTY port
>>>>>>> to ttymxc1, so I tried changing this to ttymxc0 as that is the port
>>>>>>> mapped to the debug interface on the development board. Still nothing at
>>>>>>> the console.
>>>>>>
>>>>>> That is one of the things you need to change indeed. However, things already
>>>>>> went wrong way before that, because you should have gotten U-Boot and kernel
>>>>>> debug output on the console.
>>>>>>
>>>>>> There are a number of things you have to change in a defconfig when you
>>>>>> switch
>>>>>> to a different (but similar) board. I'm going to list them below with the
>>>>>> symbol
>>>>>> names, not how they appear in the menu. You can always search for those
>>>>>> symbols
>>>>>> in `make menuconfig` by typing /
>>>>>>
>>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
>>>>>> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>>>>>>
>>>>>> You should check Variscite's yocto layer to see if they use the NXP TF-A
>>>>>> or if
>>>>>> they fork it even more. They may also use a different version.
>>>>>>
>>>>>>
>>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>>>>>>
>>>>>> I expect that this will be OK for the Variscite board as well, but it is
>>>>>> possible that they have defined their own platform.
>>>>>>
>>>>>>
>>>>>>
>>>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
>>>>>> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>>
>>>>>> You should check Variscite's yocto layer to see if they use the NXP U-Boot
>>>>>> or if
>>>>>> they fork it even more. They may also use a different version.
>>>>>>
>>>>>>
>>>>>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>>>>>>
>>>>>> This needs to change to the U-Boot defconfig. That defconfig could be in
>>>>>> NXP's
>>>>>> U-Boot fork already, or it could be in Variscite's fork, or Variscite may
>>>>>> supply
>>>>>> it in their u-boot yocto recipe.
>>>>>>
>>>>>>
>>>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
>>>>>> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
>>>>>> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
>>>>>> freescale/imx8mm-evk-revb-qca-wifi"
>>>>>>
>>>>>> You probably start to know the drill, right? The defconfig is probably OK,
>>>>>> although it's possible that Variscite appends a fragment to it in their
>>>>>> bbappend. The DTS name is most definitely not OK, but it might come from
>>>>>> Variscite's metalayer instead of NXP's kernel. The kernel is unlikely to be
>>>>>> forked by Variscite so that one is probably OK, but it may be a different
>>>>>> version.
>>>>>>
>>>>>>
>>>>>>> I tried changing the init system from busybox to systemd. Still nothing.
>>>>>>
>>>>>> No, busybox init should work fine.
>>>>>>
>>>>>>
>>>>>>> I feel like I am poking around in the dark. Any thoughts on what I
>>>>>>> should try next?
>>>>>>
>>>>>> If you do manage to advance with this, there are two contributions you
>>>>>> could make:
>>>>>> - You can add a defconfig for the Variscite board.
>>>>>> - You could update the documentation with a "how to add support for a new
>>>>>> board"
>>>>>> section that explains what I wrote above in a better (more generic) way.
>>>>>>
>>>>>>
>>>>>> Regards,
>>>>>> Arnout
>>>>>>
>>>>
>>
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-24 16:04 ` Arnout Vandecappelle via buildroot
@ 2024-09-24 16:11 ` Neil Webster
2024-09-24 17:58 ` Neil Webster
0 siblings, 1 reply; 15+ messages in thread
From: Neil Webster @ 2024-09-24 16:11 UTC (permalink / raw)
To: Arnout Vandecappelle, buildroot@buildroot.org
Hi Arnout,
Yes I had found that just after I posted. The build has progressed much
further but bails with this message ...
GIT_DIR=.
PATH="/home/neil/buildroot-2024.08/output/host/bin:/home/neil/buildroot-2024.08/output/host/sbin:/home/neil/.local/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/snap/bin:/snap/bin"
PKG_CONFIG="/home/neil/buildroot-2024.08/output/host/bin/pkg-config"
PKG_CONFIG_SYSROOT_DIR="/" PKG_CONFIG_ALLOW_SYSTEM_CFLAGS=1
PKG_CONFIG_ALLOW_SYSTEM_LIBS=1
PKG_CONFIG_LIBDIR="/home/neil/buildroot-2024.08/output/host/lib/pkgconfig:/home/neil/buildroot-2024.08/output/host/share/pkgconfig"
BR_BINARIES_DIR=/home/neil/buildroot-2024.08/output/images
KCFLAGS=-Wno-attribute-alias /usr/bin/make -j9 HOSTCC="/usr/bin/gcc -O2
-isystem /home/neil/buildroot-2024.08/output/host/include
-L/home/neil/buildroot-2024.08/output/host/lib
-Wl,-rpath,/home/neil/buildroot-2024.08/output/host/lib" ARCH=arm64
INSTALL_MOD_PATH=/home/neil/buildroot-2024.08/output/target
CROSS_COMPILE="/home/neil/buildroot-2024.08/output/host/bin/aarch64-buildroot-linux-gnu-"
WERROR=0 REGENERATE_PARSERS=1
DEPMOD=/home/neil/buildroot-2024.08/output/host/sbin/depmod
INSTALL_MOD_STRIP=1 -C
/home/neil/buildroot-2024.08/output/build/linux-custom
variscite/imx8mm-var-dart-dt8mcustomboard.dts.dtb
variscite/imx8mm-var-dart.dtsi.dtb variscite/imx8mm.dtsi.dtb
make[3]: *** No rule to make target
'arch/arm64/boot/dts/variscite/imx8mm-var-dart-dt8mcustomboard.dts.dtb'.
Stop.
make[2]: *** [Makefile:1471:
variscite/imx8mm-var-dart-dt8mcustomboard.dts.dtb] Error 2
make[1]: *** [package/pkg-generic.mk:289:
/home/neil/buildroot-2024.08/output/build/linux-custom/.stamp_built] Error 2
make: *** [Makefile:83: _all] Error 2
Regards, Neil
On 2024-09-24 12:04 p.m., Arnout Vandecappelle wrote:
>
>
> On 24/09/2024 17:24, Neil Webster wrote:
>> Hi Arnout,
>>
>> I was using an incorrect version and the url was not correct.
>>
>> The Yocto build uses 6.1.36-2.1.0 and I changed the three tarballs to
>> that. I also disabled the hash checking as per your previous comment.
>> The download now works but I hit this error ...
>>
>> INSTALL
>> /home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-gnu/
>> sysroot/usr/include
>> if ! support/scripts/check-kernel-headers.sh
>> /home/neil/buildroot-2024.08/ output/build
>> /home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-
>> gnu/sysroot 6.6 strict; then exit 1; fi
>> Incorrect selection of kernel headers: expected 6.6.x, got 6.1.x
>
> As it says: you have to change the kernel headers version to 6.1.x.
>
> But it's probably better to just switch to an external (Bootlin)
> toolchain. We're going to make that the default for the defconfigs in
> the future.
>
> Regards,
> Arnout
>
>>
>> Regards, Neil
>>
>>
>> On 2024-09-24 2:23 a.m., Arnout Vandecappelle wrote:
>>>
>>>
>>> On 23/09/2024 22:53, Neil Webster wrote:
>>>> Hi Arnout,
>>>>
>>>> Thanks for the quick response.
>>>>
>>>> I looked through the yocto build directory and it seems that they
>>>> are using 6.1.1-1.0.0 for all of the below.
>>>>
>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION
>>>>
>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION
>>>>
>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION
>>>>
>>>> So I changed them (.config attached).
>>>>
>>>> The build failed with the following ...
>>>>
>>>> ERROR: No hash found for linux-imx-lf-6.1.1-1.0.0.tar.gz
>>>> make[1]: *** [package/pkg-generic.mk:179:
>>>> /home/neil/buildroot-2024.08/ output/
>>>> build/linux-headers-custom/.stamp_downloaded] Error 1
>>>
>>> You probably have BR2_DOWNLOAD_FORCE_CHECK_HASHES=y turned on
>>> because you started from a defconfig that has a hash file. Either
>>> disable this option, or update
>>> board/freescale/imx8mmevk/patches/linux/linux.hash with the hash of
>>> the tarball.
>>>
>>> Regards,
>>> Arnout
>>>
>>>>
>>>> Thoughts on next steps appreciated.
>>>>
>>>> Thanks for your patience in working through this with a newbie.
>>>>
>>>> Cheers, Neil
>>>>
>>>> On 2024-09-23 3:36 p.m., Arnout Vandecappelle wrote:
>>>>>
>>>>>
>>>>> On 23/09/2024 21:30, Neil Webster wrote:
>>>>>> Hi Arnout,
>>>>>>
>>>>>> Thank you for the response.
>>>>>>
>>>>>> I will work through each of your suggestions and I started with
>>>>>> the one that you stated was definitely incorrect i.e. The DTS name.
>>>>>>
>>>>>> The Variscite device trees are described here
>>>>>>
>>>>>> https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
>>>>>>
>>>>>>
>>>>>> I found and copied three DTS(I) files
>>>>>>
>>>>>> imx8mm-var-dart-dt8mcustomboard.dts
>>>>>>
>>>>>> which #includes ...
>>>>>>
>>>>>> imx8mm-var-dart.dtsi
>>>>>>
>>>>>> which #includes ...
>>>>>>
>>>>>> imx8mm.dtsi
>>>>>
>>>>> This one, at least, should be in the kernel source itself. If
>>>>> you're using a kernel that doesn't already have imx8mm.dtsi, it's
>>>>> probably going to be wildly incompatible with Variscite's device
>>>>> tree.
>>>>>
>>>>>
>>>>>> I referenced the location of these files in
>>>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH and I see it copies them to
>>>>>> output/build/ linux-custom/arch/arm64/boot/dts/
>>>>>>
>>>>>> The subsequent build complained about missing dependencies and I
>>>>>> also had to add imx8mm-pinfunc.h and mxl-8611x.h to
>>>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is that
>>>>>
>>>>> Again, these should normally be part of the kernel already.
>>>>>
>>>>>> the correct way to add .h dependencies or is there a cleaner way
>>>>>> or doing this i.e. should the BR2_LINUX_KERNEL_CUSTOM_DTS_PATH be
>>>>>> reserved for DTS files only as the name suggests?
>>>>>
>>>>> Not really - the header files are shared between device tree and
>>>>> corresponding drivers. So they should already be part of the
>>>>> kernel source. If they are not, it's quite likely that things are
>>>>> not going to work.
>>>>>
>>>>> There may be situations where it makes sense to add header files
>>>>> to CUSTOM_DTS_PATH, but that's squarely You Must Know What You're
>>>>> Doing territory...
>>>>>
>>>>>
>>>>>>
>>>>>> Anyway the build succeeded after adding those .h files but sadly
>>>>>> still no console. I will now move onto looking at the other items
>>>>>> you mentioned.
>>>>>
>>>>> Well, I'd start with concentrating on getting output from TF-A
>>>>> and U-Boot. Right now you don't even know if the kernel is loaded!
>>>>>
>>>>>
>>>>> Regards,
>>>>> Arnout
>>>>>
>>>>>
>>>>>>
>>>>>> Cheers, Neil
>>>>>>
>>>>>> On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
>>>>>>> [You don't often get email from arnout@mind.be. Learn why this
>>>>>>> is important at https://aka.ms/LearnAboutSenderIdentification ]
>>>>>>>
>>>>>>> Hi Neil,
>>>>>>>
>>>>>>> On 19/09/2024 00:19, Neil Webster wrote:
>>>>>>>> Hello,
>>>>>>>>
>>>>>>>> I am new to Buildroot and have been struggling for a couple of
>>>>>>>> days with
>>>>>>>> something and wondering if I could get some pointers. Please
>>>>>>>> let me know
>>>>>>>> if this is not the appropriate place to post such questions.
>>>>>>>>
>>>>>>>> I want to get an embedded Linux image running on a Variscite
>>>>>>>> Dart Mini
>>>>>>>> (link below)
>>>>>>>>
>>>>>>>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/
>>>>>>>> dart- mx8m-mini-nxp-i-mx8m-mini/
>>>>>>>>
>>>>>>>> I have the SOM connected to a dev kit referenced in the same
>>>>>>>> link above.
>>>>>>>>
>>>>>>>> I wanted to use the opportunity to get familiar with Buildroot
>>>>>>>> but sadly
>>>>>>>> Variscite do not support Buildroot and instead they steered me
>>>>>>>> towards
>>>>>>>> Yocto.
>>>>>>>
>>>>>>> :sad-face:
>>>>>>>
>>>>>>>
>>>>>>>> I have been able to get an image running with Yocto following
>>>>>>>> their
>>>>>>>> recipes but I found the whole process to be obscure and opaque
>>>>>>>> and I am
>>>>>>>> therefore back to my original objective of using Buildroot.
>>>>>>>
>>>>>>> Please make sure to give this feedback to Variscite!
>>>>>>>
>>>>>>>
>>>>>>>>
>>>>>>>> I have been able to follow the tutorials and get a build
>>>>>>>> working on a
>>>>>>>> Raspberry Pi.
>>>>>>>>
>>>>>>>> However, as mentioned above there is no support available from
>>>>>>>> Variscite
>>>>>>>> and there is no specific defconfig for my hardware, so I tried
>>>>>>>> to start
>>>>>>>> with freescale_imx8mmevk_defconfig as this seems to be close
>>>>>>>> with what
>>>>>>>> appear to be correct settings under the "target options" menu.
>>>>>>>
>>>>>>> Yes, that's an excellent start!
>>>>>>>
>>>>>>> ... but not enough to get a working board...
>>>>>>>
>>>>>>>
>>>>>>>> However I am not getting anything at the console.
>>>>>>>>
>>>>>>>> I noticed that the freescale_imx8mmevk_defconfig sets the getty
>>>>>>>> TTY port
>>>>>>>> to ttymxc1, so I tried changing this to ttymxc0 as that is the
>>>>>>>> port
>>>>>>>> mapped to the debug interface on the development board. Still
>>>>>>>> nothing at
>>>>>>>> the console.
>>>>>>>
>>>>>>> That is one of the things you need to change indeed. However,
>>>>>>> things already
>>>>>>> went wrong way before that, because you should have gotten
>>>>>>> U-Boot and kernel
>>>>>>> debug output on the console.
>>>>>>>
>>>>>>> There are a number of things you have to change in a defconfig
>>>>>>> when you switch
>>>>>>> to a different (but similar) board. I'm going to list them below
>>>>>>> with the symbol
>>>>>>> names, not how they appear in the menu. You can always search
>>>>>>> for those symbols
>>>>>>> in `make menuconfig` by typing /
>>>>>>>
>>>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
>>>>>>> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>>>>>>>
>>>>>>>
>>>>>>> You should check Variscite's yocto layer to see if they use the
>>>>>>> NXP TF-A or if
>>>>>>> they fork it even more. They may also use a different version.
>>>>>>>
>>>>>>>
>>>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>>>>>>>
>>>>>>> I expect that this will be OK for the Variscite board as well,
>>>>>>> but it is
>>>>>>> possible that they have defined their own platform.
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
>>>>>>> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>>>
>>>>>>>
>>>>>>> You should check Variscite's yocto layer to see if they use the
>>>>>>> NXP U-Boot or if
>>>>>>> they fork it even more. They may also use a different version.
>>>>>>>
>>>>>>>
>>>>>>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>>>>>>>
>>>>>>> This needs to change to the U-Boot defconfig. That defconfig
>>>>>>> could be in NXP's
>>>>>>> U-Boot fork already, or it could be in Variscite's fork, or
>>>>>>> Variscite may supply
>>>>>>> it in their u-boot yocto recipe.
>>>>>>>
>>>>>>>
>>>>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
>>>>>>> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>>>
>>>>>>> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
>>>>>>> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
>>>>>>> freescale/imx8mm-evk-revb-qca-wifi"
>>>>>>>
>>>>>>> You probably start to know the drill, right? The defconfig is
>>>>>>> probably OK,
>>>>>>> although it's possible that Variscite appends a fragment to it
>>>>>>> in their
>>>>>>> bbappend. The DTS name is most definitely not OK, but it might
>>>>>>> come from
>>>>>>> Variscite's metalayer instead of NXP's kernel. The kernel is
>>>>>>> unlikely to be
>>>>>>> forked by Variscite so that one is probably OK, but it may be a
>>>>>>> different version.
>>>>>>>
>>>>>>>
>>>>>>>> I tried changing the init system from busybox to systemd. Still
>>>>>>>> nothing.
>>>>>>>
>>>>>>> No, busybox init should work fine.
>>>>>>>
>>>>>>>
>>>>>>>> I feel like I am poking around in the dark. Any thoughts on what I
>>>>>>>> should try next?
>>>>>>>
>>>>>>> If you do manage to advance with this, there are two
>>>>>>> contributions you could make:
>>>>>>> - You can add a defconfig for the Variscite board.
>>>>>>> - You could update the documentation with a "how to add support
>>>>>>> for a new board"
>>>>>>> section that explains what I wrote above in a better (more
>>>>>>> generic) way.
>>>>>>>
>>>>>>>
>>>>>>> Regards,
>>>>>>> Arnout
>>>>>>>
>>>>>
>>>
>
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-24 16:11 ` Neil Webster
@ 2024-09-24 17:58 ` Neil Webster
2024-09-24 19:05 ` Neil Webster
0 siblings, 1 reply; 15+ messages in thread
From: Neil Webster @ 2024-09-24 17:58 UTC (permalink / raw)
To: Arnout Vandecappelle, buildroot@buildroot.org
Quick update. Sorry for all the noise but I don't want to send you down
a bad path ...
I had previously zapped my .config and in remaking it I placed the dts
file pointers in the "in-tree" rather than "out-of-tree" entry. I have
moved them and the build is progressing. I will update again with results.
Cheers, Neil
On 2024-09-24 12:11 p.m., Neil Webster wrote:
> Hi Arnout,
>
> Yes I had found that just after I posted. The build has progressed
> much further but bails with this message ...
>
> GIT_DIR=.
> PATH="/home/neil/buildroot-2024.08/output/host/bin:/home/neil/buildroot-2024.08/output/host/sbin:/home/neil/.local/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/snap/bin:/snap/bin"
> PKG_CONFIG="/home/neil/buildroot-2024.08/output/host/bin/pkg-config"
> PKG_CONFIG_SYSROOT_DIR="/" PKG_CONFIG_ALLOW_SYSTEM_CFLAGS=1
> PKG_CONFIG_ALLOW_SYSTEM_LIBS=1
> PKG_CONFIG_LIBDIR="/home/neil/buildroot-2024.08/output/host/lib/pkgconfig:/home/neil/buildroot-2024.08/output/host/share/pkgconfig"
> BR_BINARIES_DIR=/home/neil/buildroot-2024.08/output/images
> KCFLAGS=-Wno-attribute-alias /usr/bin/make -j9 HOSTCC="/usr/bin/gcc
> -O2 -isystem /home/neil/buildroot-2024.08/output/host/include
> -L/home/neil/buildroot-2024.08/output/host/lib
> -Wl,-rpath,/home/neil/buildroot-2024.08/output/host/lib" ARCH=arm64
> INSTALL_MOD_PATH=/home/neil/buildroot-2024.08/output/target
> CROSS_COMPILE="/home/neil/buildroot-2024.08/output/host/bin/aarch64-buildroot-linux-gnu-"
> WERROR=0 REGENERATE_PARSERS=1
> DEPMOD=/home/neil/buildroot-2024.08/output/host/sbin/depmod
> INSTALL_MOD_STRIP=1 -C
> /home/neil/buildroot-2024.08/output/build/linux-custom
> variscite/imx8mm-var-dart-dt8mcustomboard.dts.dtb
> variscite/imx8mm-var-dart.dtsi.dtb variscite/imx8mm.dtsi.dtb
> make[3]: *** No rule to make target
> 'arch/arm64/boot/dts/variscite/imx8mm-var-dart-dt8mcustomboard.dts.dtb'.
> Stop.
> make[2]: *** [Makefile:1471:
> variscite/imx8mm-var-dart-dt8mcustomboard.dts.dtb] Error 2
> make[1]: *** [package/pkg-generic.mk:289:
> /home/neil/buildroot-2024.08/output/build/linux-custom/.stamp_built]
> Error 2
> make: *** [Makefile:83: _all] Error 2
>
> Regards, Neil
>
> On 2024-09-24 12:04 p.m., Arnout Vandecappelle wrote:
>>
>>
>> On 24/09/2024 17:24, Neil Webster wrote:
>>> Hi Arnout,
>>>
>>> I was using an incorrect version and the url was not correct.
>>>
>>> The Yocto build uses 6.1.36-2.1.0 and I changed the three tarballs
>>> to that. I also disabled the hash checking as per your previous
>>> comment. The download now works but I hit this error ...
>>>
>>> INSTALL
>>> /home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-gnu/
>>> sysroot/usr/include
>>> if ! support/scripts/check-kernel-headers.sh
>>> /home/neil/buildroot-2024.08/ output/build
>>> /home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-
>>> gnu/sysroot 6.6 strict; then exit 1; fi
>>> Incorrect selection of kernel headers: expected 6.6.x, got 6.1.x
>>
>> As it says: you have to change the kernel headers version to 6.1.x.
>>
>> But it's probably better to just switch to an external (Bootlin)
>> toolchain. We're going to make that the default for the defconfigs in
>> the future.
>>
>> Regards,
>> Arnout
>>
>>>
>>> Regards, Neil
>>>
>>>
>>> On 2024-09-24 2:23 a.m., Arnout Vandecappelle wrote:
>>>>
>>>>
>>>> On 23/09/2024 22:53, Neil Webster wrote:
>>>>> Hi Arnout,
>>>>>
>>>>> Thanks for the quick response.
>>>>>
>>>>> I looked through the yocto build directory and it seems that they
>>>>> are using 6.1.1-1.0.0 for all of the below.
>>>>>
>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION
>>>>>
>>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION
>>>>>
>>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION
>>>>>
>>>>> So I changed them (.config attached).
>>>>>
>>>>> The build failed with the following ...
>>>>>
>>>>> ERROR: No hash found for linux-imx-lf-6.1.1-1.0.0.tar.gz
>>>>> make[1]: *** [package/pkg-generic.mk:179:
>>>>> /home/neil/buildroot-2024.08/ output/
>>>>> build/linux-headers-custom/.stamp_downloaded] Error 1
>>>>
>>>> You probably have BR2_DOWNLOAD_FORCE_CHECK_HASHES=y turned on
>>>> because you started from a defconfig that has a hash file. Either
>>>> disable this option, or update
>>>> board/freescale/imx8mmevk/patches/linux/linux.hash with the hash of
>>>> the tarball.
>>>>
>>>> Regards,
>>>> Arnout
>>>>
>>>>>
>>>>> Thoughts on next steps appreciated.
>>>>>
>>>>> Thanks for your patience in working through this with a newbie.
>>>>>
>>>>> Cheers, Neil
>>>>>
>>>>> On 2024-09-23 3:36 p.m., Arnout Vandecappelle wrote:
>>>>>>
>>>>>>
>>>>>> On 23/09/2024 21:30, Neil Webster wrote:
>>>>>>> Hi Arnout,
>>>>>>>
>>>>>>> Thank you for the response.
>>>>>>>
>>>>>>> I will work through each of your suggestions and I started with
>>>>>>> the one that you stated was definitely incorrect i.e. The DTS name.
>>>>>>>
>>>>>>> The Variscite device trees are described here
>>>>>>>
>>>>>>> https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
>>>>>>>
>>>>>>>
>>>>>>> I found and copied three DTS(I) files
>>>>>>>
>>>>>>> imx8mm-var-dart-dt8mcustomboard.dts
>>>>>>>
>>>>>>> which #includes ...
>>>>>>>
>>>>>>> imx8mm-var-dart.dtsi
>>>>>>>
>>>>>>> which #includes ...
>>>>>>>
>>>>>>> imx8mm.dtsi
>>>>>>
>>>>>> This one, at least, should be in the kernel source itself. If
>>>>>> you're using a kernel that doesn't already have imx8mm.dtsi, it's
>>>>>> probably going to be wildly incompatible with Variscite's device
>>>>>> tree.
>>>>>>
>>>>>>
>>>>>>> I referenced the location of these files in
>>>>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH and I see it copies them to
>>>>>>> output/build/ linux-custom/arch/arm64/boot/dts/
>>>>>>>
>>>>>>> The subsequent build complained about missing dependencies and I
>>>>>>> also had to add imx8mm-pinfunc.h and mxl-8611x.h to
>>>>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is that
>>>>>>
>>>>>> Again, these should normally be part of the kernel already.
>>>>>>
>>>>>>> the correct way to add .h dependencies or is there a cleaner way
>>>>>>> or doing this i.e. should the BR2_LINUX_KERNEL_CUSTOM_DTS_PATH
>>>>>>> be reserved for DTS files only as the name suggests?
>>>>>>
>>>>>> Not really - the header files are shared between device tree and
>>>>>> corresponding drivers. So they should already be part of the
>>>>>> kernel source. If they are not, it's quite likely that things are
>>>>>> not going to work.
>>>>>>
>>>>>> There may be situations where it makes sense to add header files
>>>>>> to CUSTOM_DTS_PATH, but that's squarely You Must Know What You're
>>>>>> Doing territory...
>>>>>>
>>>>>>
>>>>>>>
>>>>>>> Anyway the build succeeded after adding those .h files but sadly
>>>>>>> still no console. I will now move onto looking at the other
>>>>>>> items you mentioned.
>>>>>>
>>>>>> Well, I'd start with concentrating on getting output from TF-A
>>>>>> and U-Boot. Right now you don't even know if the kernel is loaded!
>>>>>>
>>>>>>
>>>>>> Regards,
>>>>>> Arnout
>>>>>>
>>>>>>
>>>>>>>
>>>>>>> Cheers, Neil
>>>>>>>
>>>>>>> On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
>>>>>>>> [You don't often get email from arnout@mind.be. Learn why this
>>>>>>>> is important at https://aka.ms/LearnAboutSenderIdentification ]
>>>>>>>>
>>>>>>>> Hi Neil,
>>>>>>>>
>>>>>>>> On 19/09/2024 00:19, Neil Webster wrote:
>>>>>>>>> Hello,
>>>>>>>>>
>>>>>>>>> I am new to Buildroot and have been struggling for a couple of
>>>>>>>>> days with
>>>>>>>>> something and wondering if I could get some pointers. Please
>>>>>>>>> let me know
>>>>>>>>> if this is not the appropriate place to post such questions.
>>>>>>>>>
>>>>>>>>> I want to get an embedded Linux image running on a Variscite
>>>>>>>>> Dart Mini
>>>>>>>>> (link below)
>>>>>>>>>
>>>>>>>>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/
>>>>>>>>> dart- mx8m-mini-nxp-i-mx8m-mini/
>>>>>>>>>
>>>>>>>>> I have the SOM connected to a dev kit referenced in the same
>>>>>>>>> link above.
>>>>>>>>>
>>>>>>>>> I wanted to use the opportunity to get familiar with Buildroot
>>>>>>>>> but sadly
>>>>>>>>> Variscite do not support Buildroot and instead they steered me
>>>>>>>>> towards
>>>>>>>>> Yocto.
>>>>>>>>
>>>>>>>> :sad-face:
>>>>>>>>
>>>>>>>>
>>>>>>>>> I have been able to get an image running with Yocto following
>>>>>>>>> their
>>>>>>>>> recipes but I found the whole process to be obscure and opaque
>>>>>>>>> and I am
>>>>>>>>> therefore back to my original objective of using Buildroot.
>>>>>>>>
>>>>>>>> Please make sure to give this feedback to Variscite!
>>>>>>>>
>>>>>>>>
>>>>>>>>>
>>>>>>>>> I have been able to follow the tutorials and get a build
>>>>>>>>> working on a
>>>>>>>>> Raspberry Pi.
>>>>>>>>>
>>>>>>>>> However, as mentioned above there is no support available from
>>>>>>>>> Variscite
>>>>>>>>> and there is no specific defconfig for my hardware, so I tried
>>>>>>>>> to start
>>>>>>>>> with freescale_imx8mmevk_defconfig as this seems to be close
>>>>>>>>> with what
>>>>>>>>> appear to be correct settings under the "target options" menu.
>>>>>>>>
>>>>>>>> Yes, that's an excellent start!
>>>>>>>>
>>>>>>>> ... but not enough to get a working board...
>>>>>>>>
>>>>>>>>
>>>>>>>>> However I am not getting anything at the console.
>>>>>>>>>
>>>>>>>>> I noticed that the freescale_imx8mmevk_defconfig sets the
>>>>>>>>> getty TTY port
>>>>>>>>> to ttymxc1, so I tried changing this to ttymxc0 as that is the
>>>>>>>>> port
>>>>>>>>> mapped to the debug interface on the development board. Still
>>>>>>>>> nothing at
>>>>>>>>> the console.
>>>>>>>>
>>>>>>>> That is one of the things you need to change indeed. However,
>>>>>>>> things already
>>>>>>>> went wrong way before that, because you should have gotten
>>>>>>>> U-Boot and kernel
>>>>>>>> debug output on the console.
>>>>>>>>
>>>>>>>> There are a number of things you have to change in a defconfig
>>>>>>>> when you switch
>>>>>>>> to a different (but similar) board. I'm going to list them
>>>>>>>> below with the symbol
>>>>>>>> names, not how they appear in the menu. You can always search
>>>>>>>> for those symbols
>>>>>>>> in `make menuconfig` by typing /
>>>>>>>>
>>>>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
>>>>>>>> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>>>>>>>>
>>>>>>>>
>>>>>>>> You should check Variscite's yocto layer to see if they use the
>>>>>>>> NXP TF-A or if
>>>>>>>> they fork it even more. They may also use a different version.
>>>>>>>>
>>>>>>>>
>>>>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>>>>>>>>
>>>>>>>> I expect that this will be OK for the Variscite board as well,
>>>>>>>> but it is
>>>>>>>> possible that they have defined their own platform.
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
>>>>>>>> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>>>>
>>>>>>>>
>>>>>>>> You should check Variscite's yocto layer to see if they use the
>>>>>>>> NXP U-Boot or if
>>>>>>>> they fork it even more. They may also use a different version.
>>>>>>>>
>>>>>>>>
>>>>>>>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>>>>>>>>
>>>>>>>> This needs to change to the U-Boot defconfig. That defconfig
>>>>>>>> could be in NXP's
>>>>>>>> U-Boot fork already, or it could be in Variscite's fork, or
>>>>>>>> Variscite may supply
>>>>>>>> it in their u-boot yocto recipe.
>>>>>>>>
>>>>>>>>
>>>>>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
>>>>>>>> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>>>>
>>>>>>>> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
>>>>>>>> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
>>>>>>>> freescale/imx8mm-evk-revb-qca-wifi"
>>>>>>>>
>>>>>>>> You probably start to know the drill, right? The defconfig is
>>>>>>>> probably OK,
>>>>>>>> although it's possible that Variscite appends a fragment to it
>>>>>>>> in their
>>>>>>>> bbappend. The DTS name is most definitely not OK, but it might
>>>>>>>> come from
>>>>>>>> Variscite's metalayer instead of NXP's kernel. The kernel is
>>>>>>>> unlikely to be
>>>>>>>> forked by Variscite so that one is probably OK, but it may be a
>>>>>>>> different version.
>>>>>>>>
>>>>>>>>
>>>>>>>>> I tried changing the init system from busybox to systemd.
>>>>>>>>> Still nothing.
>>>>>>>>
>>>>>>>> No, busybox init should work fine.
>>>>>>>>
>>>>>>>>
>>>>>>>>> I feel like I am poking around in the dark. Any thoughts on
>>>>>>>>> what I
>>>>>>>>> should try next?
>>>>>>>>
>>>>>>>> If you do manage to advance with this, there are two
>>>>>>>> contributions you could make:
>>>>>>>> - You can add a defconfig for the Variscite board.
>>>>>>>> - You could update the documentation with a "how to add support
>>>>>>>> for a new board"
>>>>>>>> section that explains what I wrote above in a better (more
>>>>>>>> generic) way.
>>>>>>>>
>>>>>>>>
>>>>>>>> Regards,
>>>>>>>> Arnout
>>>>>>>>
>>>>>>
>>>>
>>
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-24 17:58 ` Neil Webster
@ 2024-09-24 19:05 ` Neil Webster
2024-09-24 19:09 ` Fabio Estevam
0 siblings, 1 reply; 15+ messages in thread
From: Neil Webster @ 2024-09-24 19:05 UTC (permalink / raw)
To: Arnout Vandecappelle, buildroot@buildroot.org
Hi Arnout,
Build completed with no errors but sadly still no console.
Just to summarise what has been changed:-
BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION
BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION
BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION
BR2_LINUX_KERNEL_INTREE_DTS_NAME
BR2_LINUX_KERNEL_CUSTOM_DTS_PATH
The items below you had mentioned but are still set to the original
values (as shown) from the initial defconfig
BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
Should I try changing these? If so what to? Any other ideas?
Cheers, Neil
On 2024-09-24 1:58 p.m., Neil Webster wrote:
> Quick update. Sorry for all the noise but I don't want to send you
> down a bad path ...
>
> I had previously zapped my .config and in remaking it I placed the dts
> file pointers in the "in-tree" rather than "out-of-tree" entry. I have
> moved them and the build is progressing. I will update again with
> results.
>
> Cheers, Neil
>
> On 2024-09-24 12:11 p.m., Neil Webster wrote:
>> Hi Arnout,
>>
>> Yes I had found that just after I posted. The build has progressed
>> much further but bails with this message ...
>>
>> GIT_DIR=.
>> PATH="/home/neil/buildroot-2024.08/output/host/bin:/home/neil/buildroot-2024.08/output/host/sbin:/home/neil/.local/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/snap/bin:/snap/bin"
>> PKG_CONFIG="/home/neil/buildroot-2024.08/output/host/bin/pkg-config"
>> PKG_CONFIG_SYSROOT_DIR="/" PKG_CONFIG_ALLOW_SYSTEM_CFLAGS=1
>> PKG_CONFIG_ALLOW_SYSTEM_LIBS=1
>> PKG_CONFIG_LIBDIR="/home/neil/buildroot-2024.08/output/host/lib/pkgconfig:/home/neil/buildroot-2024.08/output/host/share/pkgconfig"
>> BR_BINARIES_DIR=/home/neil/buildroot-2024.08/output/images
>> KCFLAGS=-Wno-attribute-alias /usr/bin/make -j9 HOSTCC="/usr/bin/gcc
>> -O2 -isystem /home/neil/buildroot-2024.08/output/host/include
>> -L/home/neil/buildroot-2024.08/output/host/lib
>> -Wl,-rpath,/home/neil/buildroot-2024.08/output/host/lib" ARCH=arm64
>> INSTALL_MOD_PATH=/home/neil/buildroot-2024.08/output/target
>> CROSS_COMPILE="/home/neil/buildroot-2024.08/output/host/bin/aarch64-buildroot-linux-gnu-"
>> WERROR=0 REGENERATE_PARSERS=1
>> DEPMOD=/home/neil/buildroot-2024.08/output/host/sbin/depmod
>> INSTALL_MOD_STRIP=1 -C
>> /home/neil/buildroot-2024.08/output/build/linux-custom
>> variscite/imx8mm-var-dart-dt8mcustomboard.dts.dtb
>> variscite/imx8mm-var-dart.dtsi.dtb variscite/imx8mm.dtsi.dtb
>> make[3]: *** No rule to make target
>> 'arch/arm64/boot/dts/variscite/imx8mm-var-dart-dt8mcustomboard.dts.dtb'.
>> Stop.
>> make[2]: *** [Makefile:1471:
>> variscite/imx8mm-var-dart-dt8mcustomboard.dts.dtb] Error 2
>> make[1]: *** [package/pkg-generic.mk:289:
>> /home/neil/buildroot-2024.08/output/build/linux-custom/.stamp_built]
>> Error 2
>> make: *** [Makefile:83: _all] Error 2
>>
>> Regards, Neil
>>
>> On 2024-09-24 12:04 p.m., Arnout Vandecappelle wrote:
>>>
>>>
>>> On 24/09/2024 17:24, Neil Webster wrote:
>>>> Hi Arnout,
>>>>
>>>> I was using an incorrect version and the url was not correct.
>>>>
>>>> The Yocto build uses 6.1.36-2.1.0 and I changed the three tarballs
>>>> to that. I also disabled the hash checking as per your previous
>>>> comment. The download now works but I hit this error ...
>>>>
>>>> INSTALL
>>>> /home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-gnu/
>>>> sysroot/usr/include
>>>> if ! support/scripts/check-kernel-headers.sh
>>>> /home/neil/buildroot-2024.08/ output/build
>>>> /home/neil/buildroot-2024.08/output/host/aarch64-buildroot-linux-
>>>> gnu/sysroot 6.6 strict; then exit 1; fi
>>>> Incorrect selection of kernel headers: expected 6.6.x, got 6.1.x
>>>
>>> As it says: you have to change the kernel headers version to 6.1.x.
>>>
>>> But it's probably better to just switch to an external (Bootlin)
>>> toolchain. We're going to make that the default for the defconfigs
>>> in the future.
>>>
>>> Regards,
>>> Arnout
>>>
>>>>
>>>> Regards, Neil
>>>>
>>>>
>>>> On 2024-09-24 2:23 a.m., Arnout Vandecappelle wrote:
>>>>>
>>>>>
>>>>> On 23/09/2024 22:53, Neil Webster wrote:
>>>>>> Hi Arnout,
>>>>>>
>>>>>> Thanks for the quick response.
>>>>>>
>>>>>> I looked through the yocto build directory and it seems that they
>>>>>> are using 6.1.1-1.0.0 for all of the below.
>>>>>>
>>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION
>>>>>>
>>>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION
>>>>>>
>>>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION
>>>>>>
>>>>>> So I changed them (.config attached).
>>>>>>
>>>>>> The build failed with the following ...
>>>>>>
>>>>>> ERROR: No hash found for linux-imx-lf-6.1.1-1.0.0.tar.gz
>>>>>> make[1]: *** [package/pkg-generic.mk:179:
>>>>>> /home/neil/buildroot-2024.08/ output/
>>>>>> build/linux-headers-custom/.stamp_downloaded] Error 1
>>>>>
>>>>> You probably have BR2_DOWNLOAD_FORCE_CHECK_HASHES=y turned on
>>>>> because you started from a defconfig that has a hash file. Either
>>>>> disable this option, or update
>>>>> board/freescale/imx8mmevk/patches/linux/linux.hash with the hash
>>>>> of the tarball.
>>>>>
>>>>> Regards,
>>>>> Arnout
>>>>>
>>>>>>
>>>>>> Thoughts on next steps appreciated.
>>>>>>
>>>>>> Thanks for your patience in working through this with a newbie.
>>>>>>
>>>>>> Cheers, Neil
>>>>>>
>>>>>> On 2024-09-23 3:36 p.m., Arnout Vandecappelle wrote:
>>>>>>>
>>>>>>>
>>>>>>> On 23/09/2024 21:30, Neil Webster wrote:
>>>>>>>> Hi Arnout,
>>>>>>>>
>>>>>>>> Thank you for the response.
>>>>>>>>
>>>>>>>> I will work through each of your suggestions and I started with
>>>>>>>> the one that you stated was definitely incorrect i.e. The DTS
>>>>>>>> name.
>>>>>>>>
>>>>>>>> The Variscite device trees are described here
>>>>>>>>
>>>>>>>> https://www.variscite.com/blog/getting-started-with-variscite-device-trees/
>>>>>>>>
>>>>>>>>
>>>>>>>> I found and copied three DTS(I) files
>>>>>>>>
>>>>>>>> imx8mm-var-dart-dt8mcustomboard.dts
>>>>>>>>
>>>>>>>> which #includes ...
>>>>>>>>
>>>>>>>> imx8mm-var-dart.dtsi
>>>>>>>>
>>>>>>>> which #includes ...
>>>>>>>>
>>>>>>>> imx8mm.dtsi
>>>>>>>
>>>>>>> This one, at least, should be in the kernel source itself. If
>>>>>>> you're using a kernel that doesn't already have imx8mm.dtsi,
>>>>>>> it's probably going to be wildly incompatible with Variscite's
>>>>>>> device tree.
>>>>>>>
>>>>>>>
>>>>>>>> I referenced the location of these files in
>>>>>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH and I see it copies them to
>>>>>>>> output/build/ linux-custom/arch/arm64/boot/dts/
>>>>>>>>
>>>>>>>> The subsequent build complained about missing dependencies and
>>>>>>>> I also had to add imx8mm-pinfunc.h and mxl-8611x.h to
>>>>>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH. Is that
>>>>>>>
>>>>>>> Again, these should normally be part of the kernel already.
>>>>>>>
>>>>>>>> the correct way to add .h dependencies or is there a cleaner
>>>>>>>> way or doing this i.e. should the
>>>>>>>> BR2_LINUX_KERNEL_CUSTOM_DTS_PATH be reserved for DTS files only
>>>>>>>> as the name suggests?
>>>>>>>
>>>>>>> Not really - the header files are shared between device tree
>>>>>>> and corresponding drivers. So they should already be part of the
>>>>>>> kernel source. If they are not, it's quite likely that things
>>>>>>> are not going to work.
>>>>>>>
>>>>>>> There may be situations where it makes sense to add header
>>>>>>> files to CUSTOM_DTS_PATH, but that's squarely You Must Know What
>>>>>>> You're Doing territory...
>>>>>>>
>>>>>>>
>>>>>>>>
>>>>>>>> Anyway the build succeeded after adding those .h files but
>>>>>>>> sadly still no console. I will now move onto looking at the
>>>>>>>> other items you mentioned.
>>>>>>>
>>>>>>> Well, I'd start with concentrating on getting output from TF-A
>>>>>>> and U-Boot. Right now you don't even know if the kernel is loaded!
>>>>>>>
>>>>>>>
>>>>>>> Regards,
>>>>>>> Arnout
>>>>>>>
>>>>>>>
>>>>>>>>
>>>>>>>> Cheers, Neil
>>>>>>>>
>>>>>>>> On 2024-09-19 7:53 a.m., Arnout Vandecappelle wrote:
>>>>>>>>> [You don't often get email from arnout@mind.be. Learn why this
>>>>>>>>> is important at https://aka.ms/LearnAboutSenderIdentification ]
>>>>>>>>>
>>>>>>>>> Hi Neil,
>>>>>>>>>
>>>>>>>>> On 19/09/2024 00:19, Neil Webster wrote:
>>>>>>>>>> Hello,
>>>>>>>>>>
>>>>>>>>>> I am new to Buildroot and have been struggling for a couple
>>>>>>>>>> of days with
>>>>>>>>>> something and wondering if I could get some pointers. Please
>>>>>>>>>> let me know
>>>>>>>>>> if this is not the appropriate place to post such questions.
>>>>>>>>>>
>>>>>>>>>> I want to get an embedded Linux image running on a Variscite
>>>>>>>>>> Dart Mini
>>>>>>>>>> (link below)
>>>>>>>>>>
>>>>>>>>>> https://www.variscite.com/product/system-on-module-som/cortex-a53-krait/
>>>>>>>>>> dart- mx8m-mini-nxp-i-mx8m-mini/
>>>>>>>>>>
>>>>>>>>>> I have the SOM connected to a dev kit referenced in the same
>>>>>>>>>> link above.
>>>>>>>>>>
>>>>>>>>>> I wanted to use the opportunity to get familiar with
>>>>>>>>>> Buildroot but sadly
>>>>>>>>>> Variscite do not support Buildroot and instead they steered
>>>>>>>>>> me towards
>>>>>>>>>> Yocto.
>>>>>>>>>
>>>>>>>>> :sad-face:
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>> I have been able to get an image running with Yocto following
>>>>>>>>>> their
>>>>>>>>>> recipes but I found the whole process to be obscure and
>>>>>>>>>> opaque and I am
>>>>>>>>>> therefore back to my original objective of using Buildroot.
>>>>>>>>>
>>>>>>>>> Please make sure to give this feedback to Variscite!
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>>
>>>>>>>>>> I have been able to follow the tutorials and get a build
>>>>>>>>>> working on a
>>>>>>>>>> Raspberry Pi.
>>>>>>>>>>
>>>>>>>>>> However, as mentioned above there is no support available
>>>>>>>>>> from Variscite
>>>>>>>>>> and there is no specific defconfig for my hardware, so I
>>>>>>>>>> tried to start
>>>>>>>>>> with freescale_imx8mmevk_defconfig as this seems to be close
>>>>>>>>>> with what
>>>>>>>>>> appear to be correct settings under the "target options" menu.
>>>>>>>>>
>>>>>>>>> Yes, that's an excellent start!
>>>>>>>>>
>>>>>>>>> ... but not enough to get a working board...
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>> However I am not getting anything at the console.
>>>>>>>>>>
>>>>>>>>>> I noticed that the freescale_imx8mmevk_defconfig sets the
>>>>>>>>>> getty TTY port
>>>>>>>>>> to ttymxc1, so I tried changing this to ttymxc0 as that is
>>>>>>>>>> the port
>>>>>>>>>> mapped to the debug interface on the development board. Still
>>>>>>>>>> nothing at
>>>>>>>>>> the console.
>>>>>>>>>
>>>>>>>>> That is one of the things you need to change indeed. However,
>>>>>>>>> things already
>>>>>>>>> went wrong way before that, because you should have gotten
>>>>>>>>> U-Boot and kernel
>>>>>>>>> debug output on the console.
>>>>>>>>>
>>>>>>>>> There are a number of things you have to change in a
>>>>>>>>> defconfig when you switch
>>>>>>>>> to a different (but similar) board. I'm going to list them
>>>>>>>>> below with the symbol
>>>>>>>>> names, not how they appear in the menu. You can always search
>>>>>>>>> for those symbols
>>>>>>>>> in `make menuconfig` by typing /
>>>>>>>>>
>>>>>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call
>>>>>>>>> github,nxp-imx,imx-atf,lf-6.6.23-2.0.0)/imx-atf-lf-6.6.23-2.0.0.tar.gz"
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> You should check Variscite's yocto layer to see if they use
>>>>>>>>> the NXP TF-A or if
>>>>>>>>> they fork it even more. They may also use a different version.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="imx8mm"
>>>>>>>>>
>>>>>>>>> I expect that this will be OK for the Variscite board as well,
>>>>>>>>> but it is
>>>>>>>>> possible that they have defined their own platform.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call
>>>>>>>>> github,nxp-imx,uboot-imx,lf-6.6.23-2.0.0)/uboot-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> You should check Variscite's yocto layer to see if they use
>>>>>>>>> the NXP U-Boot or if
>>>>>>>>> they fork it even more. They may also use a different version.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>>>>>>>>>
>>>>>>>>> This needs to change to the U-Boot defconfig. That defconfig
>>>>>>>>> could be in NXP's
>>>>>>>>> U-Boot fork already, or it could be in Variscite's fork, or
>>>>>>>>> Variscite may supply
>>>>>>>>> it in their u-boot yocto recipe.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call
>>>>>>>>> github,nxp-imx,linux-imx,lf-6.6.23-2.0.0)/linux-imx-lf-6.6.23-2.0.0.tar.gz"
>>>>>>>>>
>>>>>>>>> BR2_LINUX_KERNEL_DEFCONFIG="imx_v8"
>>>>>>>>> BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/imx8mm-evk
>>>>>>>>> freescale/imx8mm-evk-revb-qca-wifi"
>>>>>>>>>
>>>>>>>>> You probably start to know the drill, right? The defconfig is
>>>>>>>>> probably OK,
>>>>>>>>> although it's possible that Variscite appends a fragment to it
>>>>>>>>> in their
>>>>>>>>> bbappend. The DTS name is most definitely not OK, but it might
>>>>>>>>> come from
>>>>>>>>> Variscite's metalayer instead of NXP's kernel. The kernel is
>>>>>>>>> unlikely to be
>>>>>>>>> forked by Variscite so that one is probably OK, but it may be
>>>>>>>>> a different version.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>> I tried changing the init system from busybox to systemd.
>>>>>>>>>> Still nothing.
>>>>>>>>>
>>>>>>>>> No, busybox init should work fine.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>> I feel like I am poking around in the dark. Any thoughts on
>>>>>>>>>> what I
>>>>>>>>>> should try next?
>>>>>>>>>
>>>>>>>>> If you do manage to advance with this, there are two
>>>>>>>>> contributions you could make:
>>>>>>>>> - You can add a defconfig for the Variscite board.
>>>>>>>>> - You could update the documentation with a "how to add
>>>>>>>>> support for a new board"
>>>>>>>>> section that explains what I wrote above in a better (more
>>>>>>>>> generic) way.
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> Regards,
>>>>>>>>> Arnout
>>>>>>>>>
>>>>>>>
>>>>>
>>>
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-24 19:05 ` Neil Webster
@ 2024-09-24 19:09 ` Fabio Estevam
2024-09-24 19:47 ` Neil Webster
0 siblings, 1 reply; 15+ messages in thread
From: Fabio Estevam @ 2024-09-24 19:09 UTC (permalink / raw)
To: Neil Webster; +Cc: buildroot@buildroot.org
On Tue, Sep 24, 2024 at 4:05 PM Neil Webster <jarraneil@gmail.com> wrote:
> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
You cannot use the U-Boot imx8mm_evk_defconfig for the i.MX8MM
Variscite Dart board.
You must use a specific i.MX8MM Variscite Dart U-Boot defconfig instead.
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-24 19:09 ` Fabio Estevam
@ 2024-09-24 19:47 ` Neil Webster
2024-09-25 17:56 ` Arnout Vandecappelle via buildroot
0 siblings, 1 reply; 15+ messages in thread
From: Neil Webster @ 2024-09-24 19:47 UTC (permalink / raw)
To: Fabio Estevam; +Cc: buildroot@buildroot.org
Thanks Fabio.
The trouble is that Variscite do not support buildroot so I can't get
anything useful out of them. I have tried. They keep trying to steer me
to Yocto.
Cheers, Neil
On 2024-09-24 3:09 p.m., Fabio Estevam wrote:
> On Tue, Sep 24, 2024 at 4:05 PM Neil Webster <jarraneil@gmail.com> wrote:
>
>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
> You cannot use the U-Boot imx8mm_evk_defconfig for the i.MX8MM
> Variscite Dart board.
>
> You must use a specific i.MX8MM Variscite Dart U-Boot defconfig instead.
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] Variscite Dart
2024-09-24 19:47 ` Neil Webster
@ 2024-09-25 17:56 ` Arnout Vandecappelle via buildroot
0 siblings, 0 replies; 15+ messages in thread
From: Arnout Vandecappelle via buildroot @ 2024-09-25 17:56 UTC (permalink / raw)
To: Neil Webster, Fabio Estevam; +Cc: buildroot@buildroot.org
On 24/09/2024 21:47, Neil Webster wrote:
> Thanks Fabio.
>
> The trouble is that Variscite do not support buildroot so I can't get anything
> useful out of them. I have tried. They keep trying to steer me to Yocto.
You can check in their yocto layer to see what they use for U-Boot defconfig.
It should be in the same .bbappend in the variscite layer where you found the
reference to the U-Boot source.
Or you can look in their custom U-Boot source in the configs/ directory, the
defconfig name probably is something recognizable.
Regards,
Arnout
>
> Cheers, Neil
>
> On 2024-09-24 3:09 p.m., Fabio Estevam wrote:
>> On Tue, Sep 24, 2024 at 4:05 PM Neil Webster <jarraneil@gmail.com> wrote:
>>
>>> BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imx8mm_evk"
>> You cannot use the U-Boot imx8mm_evk_defconfig for the i.MX8MM
>> Variscite Dart board.
>>
>> You must use a specific i.MX8MM Variscite Dart U-Boot defconfig instead.
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread
end of thread, other threads:[~2024-09-25 17:56 UTC | newest]
Thread overview: 15+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-09-18 22:19 [Buildroot] Variscite Dart Neil Webster
2024-09-19 11:53 ` Arnout Vandecappelle via buildroot
2024-09-23 19:30 ` Neil Webster
2024-09-23 19:36 ` Arnout Vandecappelle via buildroot
2024-09-23 20:53 ` Neil Webster
2024-09-24 2:58 ` Neil Webster
2024-09-24 6:23 ` Arnout Vandecappelle via buildroot
2024-09-24 15:24 ` Neil Webster
2024-09-24 16:04 ` Arnout Vandecappelle via buildroot
2024-09-24 16:11 ` Neil Webster
2024-09-24 17:58 ` Neil Webster
2024-09-24 19:05 ` Neil Webster
2024-09-24 19:09 ` Fabio Estevam
2024-09-24 19:47 ` Neil Webster
2024-09-25 17:56 ` Arnout Vandecappelle via buildroot
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox