From: Johan Sagaert <sagaert.johan@proximus.be>
To: buildroot@busybox.net
Subject: [Buildroot] problem booting from ext2 µsd card
Date: Thu, 17 Sep 2015 01:56:20 +0200 [thread overview]
Message-ID: <55FA01A4.5070107@proximus.be> (raw)
Hi
just extracted my rootfs to a ?sd card
configured u-boot to boot from it
Any idea ? i have a single ext2 partition on a 4GB transcend class 10 card.
not sure where to start searching...
Tried several cards with equal results.
used cfdisk as tool.
snip from bootlog
usbcore: registered new interface driver usb-storage
ci_hdrc ci_hdrc.1: EHCI Host Controller
ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
input: 20b8000.kpp as
/devices/soc0/soc/2000000.aips-bus/20b8000.kpp/input/input0
input: EP0700M06 as
/devices/soc0/soc/2100000.aips-bus/21a8000.i2c/i2c-2/2-0038/input/input1
rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0
snvs_rtc 20cc034.snvs-rtc-lp: rtc core: registered 20cc034.snvs-rtc-lp
as rtc1
i2c /dev entries driver
mxc_v4l2_output v4l2_out: V4L2 device registered as video16
mxc_v4l2_output v4l2_out: V4L2 device registered as video17
imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: no vqmmc regulator found
mmc0: no vmmc regulator found
mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
mmc1: no vqmmc regulator found
mmc1: no vmmc regulator found
mmc1: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA
galcore: clk_get vg clock failed, disable vg!
Galcore version 5.0.11.25762
mmc0: new high speed SDHC card at address 59b4
*mmcblk0: mmc0:59b4 USD 3.74 GiB
mmcblk0: p1*
mxc_vpu 2040000.vpu: VPU initialized
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
sgtl5000 2-000a: sgtl5000 revision 0x11
2-000a: 1200 mV normal
sgtl5000 2-000a: Using internal LDO instead of VDDD
imx-sgtl5000 sound: sgtl5000 <-> 2028000.ssi mapping ok
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
8021q: 802.1Q VLAN Support v1.8
Key type dns_resolver registered
failed to disable 1.2 GHz OPP
Registering SWP/SWPB emulation handler
input: gpio-keys as /devices/soc0/gpio-keys/input/input2
rtc-ds1307 0-0068: setting system clock to 2000-01-01 13:27:11 UTC
(946733231)
ALSA device list:
#0: sgtl5000-audio
VFS: Mounted root (ext2 filesystem) on device 179:1.
devtmpfs: mounted
Freeing unused kernel memory: 252K (80835000 - 80874000)
Starting logging: OK
Populating /dev using udev: udevd[116]: starting version 3.1.1
random: udevd urandom read with 55 bits of entropy available
done
Initializing random number generator... done.
Starting system message bus: done
Starting rpcbind: OK
Starting network...
fec 2188000.ethernet eth0: Freescale FEC PHY driver [SMSC
LAN8710/LAN8720] (mii_bus:phy_addr=2188000.ethernet:00, irq=-1)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.23.2) started
Sending discover...
Sending discover...
fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Sending discover...
Sending select for 192.168.1.145...
Lease of 192.168.1.145 obtained, lease time 3600
deleting routers
adding dns 192.168.1.1
Starting ntpd: OK
Starting dropbear sshd: OK
Starting inetd : OK
/etc/init.d/S80tunetouch: line 16: can't create
/sys/bus/i2c/devices/0-0038/threshold: nonexistent directory
/etc/init.d/S80tunetouch: line 16: can't create
/sys/bus/i2c/devices/0-0038/gain: nonexistent directory
/etc/init.d/S80tunetouch: line 16: can't create
/sys/bus/i2c/devices/0-0038/report_rate: nonexistent directory
Starting mpd: OK
Segmentation fault
fb-test 1.1.0 (rosetta)
fb res 800x480 virtual 800x480, line_len 3200, bpp 32
attempt to access beyond end of device
mmcblk0p1: rw=0, want=11524007040, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=33325320632, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=20728214080, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=8149861624, limit=7857074
attempt to access beyond end of device
Welcome to Buildrootmmcblk0p1: rw=0, want=26925577088, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=11576436144, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=26035639288, limit=7857074
attempt to access beyond end of device
apex_systems login: mmcblk0p1: rw=0, want=30960508736, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=873814192, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=18769465248, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=13401729144, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=8730814792, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=30741356216, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=7043620368, limit=7857074
attempt to access beyond end of device
mmcblk0p1: rw=0, want=13247852320, limit=7857074
attempt to access beyond end of device
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20150917/b8cdd2f8/attachment.html>
next reply other threads:[~2015-09-16 23:56 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-16 23:56 Johan Sagaert [this message]
2015-09-17 0:27 ` [Buildroot] problem booting from ext2 µsd card Brendan Heading
2015-09-17 8:03 ` Johan Sagaert
2015-09-17 11:20 ` Brendan Heading
2015-09-20 23:59 ` Johan Sagaert
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55FA01A4.5070107@proximus.be \
--to=sagaert.johan@proximus.be \
--cc=buildroot@busybox.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox