* [Buildroot] can't find root fs kernel panic [not found] <mailman.1147.1213963958.1345.buildroot@uclibc.org> @ 2008-06-20 15:03 ` Joseph G. Boike 2008-06-20 19:32 ` Peter Korsgaard ` (3 more replies) 0 siblings, 4 replies; 5+ messages in thread From: Joseph G. Boike @ 2008-06-20 15:03 UTC (permalink / raw) To: buildroot I'm hoping someone can help me with this. I'm using this morning buildroot (How do I determine the rev #?) Built for an Atmel at91sam9260 processor and eval board. I've tried using the ext2, ext2.gz and jffs root filesystems with the same results. Below is an abridged capture from the kernel during boot. I've tried google, but everything I saw was related to the bootloader pointing to the wrong disk. My u-boot invocation is: bootp 21500000 linux.gz; bootp 20410000 rootfs.ext2.gz; bootm 21500000 Is the Kernel command line correct? (I've tried 2 different boards, so I don't think it's h/w.) Regards, Joe Starting kernel ... Uncompressing Linux.................................................................................................... Linux version 2.6.24.4 (JoeB at elab14_linux.localdomain) (gcc version 4.2.1) #2 Fri Jun 20 10:07:40 EDT 2008 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 Machine: Atmel AT91SAM9260-EK Memory policy: ECC disabled, Data cache writeback Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz CPU0: D VIVT write-back cache CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: mem=64M console=ttyS0,115200 initrd=0x20410000,3145728 root=/dev/ram0 rw Memory: 64MB = 64MB total Memory: 58056KB available (3352K code, 238K data, 140K init) checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd Freeing initrd memory: 3072K NetWinder Floating Point Emulator V0.97 (double precision) DLM (built Jun 20 2008 09:40:47) installed JFS: nTxBlock = 478, nTxLock = 3824 RAMDISK driver initialized: 16 RAM disks of 15360K size 1024 blocksize RAMDISK: Couldn't find valid RAM disk image starting at 0. List of all partitions: No filesystem could mount root, tried: ext2 cramfs msdos vfat jfs Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0) ^ permalink raw reply [flat|nested] 5+ messages in thread
* [Buildroot] can't find root fs kernel panic 2008-06-20 15:03 ` [Buildroot] can't find root fs kernel panic Joseph G. Boike @ 2008-06-20 19:32 ` Peter Korsgaard 2008-06-20 20:48 ` Thiago A. Corrêa ` (2 subsequent siblings) 3 siblings, 0 replies; 5+ messages in thread From: Peter Korsgaard @ 2008-06-20 19:32 UTC (permalink / raw) To: buildroot >>>>> "Joseph" == Joseph G Boike <joe.boike@acsatlanta.com> writes: Joseph> I'm hoping someone can help me with this. Joseph> I'm using this morning buildroot (How do I determine the rev #?) type svn info Joseph> Built for an Atmel at91sam9260 processor and eval board. Joseph> I've tried using the ext2, ext2.gz and jffs root filesystems Joseph> with the same results. <cut> Joseph> Kernel command line: mem=64M console=ttyS0,115200 Joseph> initrd=0x20410000,3145728 root=/dev/ram0 rw What do you want to do? With jffs2 it sounds like you want to boot from a flash partition, but you tell the kernel to boot from a ramdisk (initrd). -- Bye, Peter Korsgaard ^ permalink raw reply [flat|nested] 5+ messages in thread
* [Buildroot] can't find root fs kernel panic 2008-06-20 15:03 ` [Buildroot] can't find root fs kernel panic Joseph G. Boike 2008-06-20 19:32 ` Peter Korsgaard @ 2008-06-20 20:48 ` Thiago A. Corrêa 2008-06-21 2:28 ` [Buildroot] can t " Mike Sander [not found] ` <485C66DD.2070304@ripnet.com> 3 siblings, 0 replies; 5+ messages in thread From: Thiago A. Corrêa @ 2008-06-20 20:48 UTC (permalink / raw) To: buildroot On Fri, Jun 20, 2008 at 12:03 PM, Joseph G. Boike <joe.boike@acsatlanta.com> wrote: > I'm hoping someone can help me with this. > I'm using this morning buildroot (How do I determine the rev #?) svn info > Built for an Atmel at91sam9260 processor and eval board. > I've tried using the ext2, ext2.gz and jffs root filesystems with the > same results. > Below is an abridged capture from the kernel during boot. > I've tried google, but everything I saw was related to the bootloader > pointing to the wrong disk. > My u-boot invocation is: > bootp 21500000 linux.gz; bootp 20410000 rootfs.ext2.gz; bootm 21500000 > Is the Kernel command line correct? There is no kernel parameters there. I guess the kernel would use the default parameters compiled within. Are you really using ramdisk? Did you compile the filesystem drivers within the kernel or as modules? I'm not familiar with arms, I use AVR32. Perhaps Ulf will be able to help you better. > (I've tried 2 different boards, so I don't think it's h/w.) > > Regards, > Joe > > Starting kernel ... > > Uncompressing > Linux.................................................................................................... > Linux version 2.6.24.4 (JoeB at elab14_linux.localdomain) (gcc version > 4.2.1) #2 Fri Jun 20 10:07:40 EDT 2008 > CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 > Machine: Atmel AT91SAM9260-EK > Memory policy: ECC disabled, Data cache writeback > Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz > CPU0: D VIVT write-back cache > CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets > CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 > Kernel command line: mem=64M console=ttyS0,115200 > initrd=0x20410000,3145728 root=/dev/ram0 rw > > Memory: 64MB = 64MB total > Memory: 58056KB available (3352K code, 238K data, 140K init) > > checking if image is initramfs...it isn't (bad gzip magic numbers); > looks like an initrd > Freeing initrd memory: 3072K > NetWinder Floating Point Emulator V0.97 (double precision) > DLM (built Jun 20 2008 09:40:47) installed > JFS: nTxBlock = 478, nTxLock = 3824 > > RAMDISK driver initialized: 16 RAM disks of 15360K size 1024 blocksize > > RAMDISK: Couldn't find valid RAM disk image starting at 0. > List of all partitions: > No filesystem could mount root, tried: ext2 cramfs msdos vfat jfs > Kernel panic - not syncing: VFS: Unable to mount root fs on > unknown-block(1,0) > > > > _______________________________________________ > buildroot mailing list > buildroot at uclibc.org > http://busybox.net/mailman/listinfo/buildroot > ^ permalink raw reply [flat|nested] 5+ messages in thread
* [Buildroot] can t find root fs kernel panic 2008-06-20 15:03 ` [Buildroot] can't find root fs kernel panic Joseph G. Boike 2008-06-20 19:32 ` Peter Korsgaard 2008-06-20 20:48 ` Thiago A. Corrêa @ 2008-06-21 2:28 ` Mike Sander [not found] ` <485C66DD.2070304@ripnet.com> 3 siblings, 0 replies; 5+ messages in thread From: Mike Sander @ 2008-06-21 2:28 UTC (permalink / raw) To: buildroot Joseph G. Boike wrote: > I'm hoping someone can help me with this. > I'm using this morning buildroot (How do I determine the rev #?) > Built for an Atmel at91sam9260 processor and eval board. > I've tried using the ext2, ext2.gz and jffs root filesystems with the > same results. > Below is an abridged capture from the kernel during boot. > I've tried google, but everything I saw was related to the bootloader > pointing to the wrong disk. > My u-boot invocation is: > bootp 21500000 linux.gz; bootp 20410000 rootfs.ext2.gz; bootm 21500000 > Is the Kernel command line correct? > (I've tried 2 different boards, so I don't think it's h/w.) > > Regards, > Joe > > Starting kernel ... > > Uncompressing > Linux.................................................................................................... > Linux version 2.6.24.4 (JoeB at elab14_linux.localdomain) (gcc version > 4.2.1) #2 Fri Jun 20 10:07:40 EDT 2008 > CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 > Machine: Atmel AT91SAM9260-EK > Memory policy: ECC disabled, Data cache writeback > Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz > CPU0: D VIVT write-back cache > CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets > CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 > Kernel command line: mem=64M console=ttyS0,115200 > initrd=0x20410000,3145728 root=/dev/ram0 rw > > Memory: 64MB = 64MB total > Memory: 58056KB available (3352K code, 238K data, 140K init) > > checking if image is initramfs...it isn't (bad gzip magic numbers); > looks like an initrd > Freeing initrd memory: 3072K > NetWinder Floating Point Emulator V0.97 (double precision) > DLM (built Jun 20 2008 09:40:47) installed > JFS: nTxBlock = 478, nTxLock = 3824 > > RAMDISK driver initialized: 16 RAM disks of 15360K size 1024 blocksize > > RAMDISK: Couldn't find valid RAM disk image starting at 0. > List of all partitions: > No filesystem could mount root, tried: ext2 cramfs msdos vfat jfs > Kernel panic - not syncing: VFS: Unable to mount root fs on > unknown-block(1,0) > > Joseph, I have just grabbed todays snapshot & built for an at91sam9260ek [you're not specific on the exact board you are using]. Using all the default I can boot and mount ext2 (i'm sure others will work). the ext2 is a good one to start with as the kernel has support for this in the default configuration. I'm using u-boot. I put the ext2 image (binaries/uclibc/rootfs.arm-20080620.ext2) at 0x21100000. I put the uImage at 0x21400000. I used the default kernel command line set up for this target (which has initrd at 21100000). Its the same as yours, but slightly different address for the initrd. Are you loading the correct file system image? Are you putting at the correct address corresponding to the kernel command line (either default or supplied by you)? Here is my u-boot stuff & boot log. Maybe this might help U-Boot> tftp 21100000 rootfs.arm-20080620.ext2 TFTP from server 192.168.1.2; our IP address is 192.168.1.3 Filename 'rootfs.arm-20080620.ext2'. Load address: 0x21100000 Loading: ################################################################# ################################################################# ################################################################# ####T ############################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####### done Bytes transferred = 4026368 (3d7000 hex) U-Boot> tftp 21400000 uImage.buildroot-20080620 TFTP from server 192.168.1.2; our IP address is 192.168.1.3 Filename 'uImage.buildroot-20080620'. Load address: 0x21400000 Loading: ################################################################# ################################################################# ################################################################# ###### done Bytes transferred = 1025408 (fa580 hex) U-Boot> bootm ## Booting image at 21400000 ... Image Name: Linux-2.6.22.1 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1025344 Bytes = 1001.3 kB Load Address: 20008000 Entry Point: 20008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux.................................................................... done, booting the kernel. Linux version 2.6.22.1 (mike at himalia) (gcc version 4.2.4) #1 Fri Jun 20 16:53:37 EDT 2008 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 Machine: Atmel AT91SAM9260-EK Memory policy: ECC disabled, Data cache writeback Clocks: CPU 198 MHz, master 99 MHz, main 18.432 MHz CPU0: D VIVT write-back cache CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets Built 1 zonelists. Total pages: 16256 Kernel command line: mem=64M console=ttyS0,115200 initrd=0x21100000,3145728 root=/dev/ram0 rw AT91: 96 gpio irqs in 3 banks PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 59648KB available (1856K code, 188K data, 100K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd Freeing initrd memory: 3072K NetWinder Floating Point Emulator V0.97 (double precision) io scheduler noop registered io scheduler anticipatory registered (default) atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize usbmon: debugfs is not available at91_ohci at91_ohci: AT91 OHCI at91_ohci at91_ohci: new USB bus registered, assigned bus number 1 at91_ohci at91_ohci: irq 20, io mem 0x00500000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. udc: at91_udc version 3 May 2006 mice: PS/2 mouse device common for all mice TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RAMDISK: ext2 filesystem found at block 0 RAMDISK: Loading 3932KiB [1 disk] into ram disk... done. VFS: Mounted root (ext2 filesystem). Freeing init memory: 100K Initializing random number generator... done. Starting network... ip: RTNETLINK answers: File exists Welcome to the Erik's uClibc development environment. uclibc login: root Mike > _______________________________________________ > buildroot mailing list > buildroot at uclibc.org > http://busybox.net/mailman/listinfo/buildroot > > > =-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- > Scanned with Copfilter Version 0.84beta3a (P3Scan 2.2.1) > AntiSpam: SpamAssassin 3.2.3 > by Markus Madlener @ http://www.copfilter.org > > ^ permalink raw reply [flat|nested] 5+ messages in thread
[parent not found: <485C66DD.2070304@ripnet.com>]
* [Buildroot] can t find root fs kernel panic [not found] ` <485C66DD.2070304@ripnet.com> @ 2008-06-23 16:48 ` Joseph G. Boike 0 siblings, 0 replies; 5+ messages in thread From: Joseph G. Boike @ 2008-06-23 16:48 UTC (permalink / raw) To: buildroot Mike Sander wrote: > Joseph G. Boike wrote: >> I'm hoping someone can help me with this. >> I'm using this morning buildroot (How do I determine the rev #?) >> Built for an Atmel at91sam9260 processor and eval board. >> I've tried using the ext2, ext2.gz and jffs root filesystems with the >> same results. >> Below is an abridged capture from the kernel during boot. >> I've tried google, but everything I saw was related to the bootloader >> pointing to the wrong disk. >> My u-boot invocation is: >> bootp 21500000 linux.gz; bootp 20410000 rootfs.ext2.gz; bootm 21500000 >> Is the Kernel command line correct? >> (I've tried 2 different boards, so I don't think it's h/w.) >> >> Regards, >> Joe >> >> Starting kernel ... >> >> Uncompressing >> Linux.................................................................................................... >> >> Linux version 2.6.24.4 (JoeB at elab14_linux.localdomain) (gcc version >> 4.2.1) #2 Fri Jun 20 10:07:40 EDT 2008 >> CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 >> Machine: Atmel AT91SAM9260-EK >> Memory policy: ECC disabled, Data cache writeback >> Clocks: CPU 199 MHz, master 99 MHz, main 18.432 MHz >> CPU0: D VIVT write-back cache >> CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets >> CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets >> Built 1 zonelists in Zone order, mobility grouping on. Total pages: >> 16256 >> Kernel command line: mem=64M console=ttyS0,115200 >> initrd=0x20410000,3145728 root=/dev/ram0 rw >> >> Memory: 64MB = 64MB total >> Memory: 58056KB available (3352K code, 238K data, 140K init) >> >> checking if image is initramfs...it isn't (bad gzip magic numbers); >> looks like an initrd >> Freeing initrd memory: 3072K >> NetWinder Floating Point Emulator V0.97 (double precision) >> DLM (built Jun 20 2008 09:40:47) installed >> JFS: nTxBlock = 478, nTxLock = 3824 >> >> RAMDISK driver initialized: 16 RAM disks of 15360K size 1024 blocksize >> >> RAMDISK: Couldn't find valid RAM disk image starting at 0. >> List of all partitions: >> No filesystem could mount root, tried: ext2 cramfs msdos vfat jfs >> Kernel panic - not syncing: VFS: Unable to mount root fs on >> unknown-block(1,0) >> >> >> > Joseph, > > I have just grabbed todays snapshot & built for an at91sam9260ek > [you're not specific on the exact board you are using]. Using all > the default I can boot and mount ext2 (i'm sure others will work). > the ext2 is a good one to start with as the kernel has support for > this in the default configuration. > > I'm using u-boot. I put the ext2 image > (binaries/uclibc/rootfs.arm-20080620.ext2) at 0x21100000. I put the > uImage at 0x21400000. I used the default kernel command line set up > for this target (which has initrd at 21100000). Its the same as > yours, but slightly different address for the initrd. Are you > loading the correct file system image? Are you putting at the correct > address corresponding to the kernel command line (either default or > supplied by you)? > > Here is my u-boot stuff & boot log. Maybe this might help > > U-Boot> tftp 21100000 rootfs.arm-20080620.ext2 > TFTP from server 192.168.1.2; our IP address is 192.168.1.3 > Filename 'rootfs.arm-20080620.ext2'. > Load address: 0x21100000 > Loading: > ################################################################# > ################################################################# > ################################################################# > ####T > ############################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ################################################################# > ####### > done > Bytes transferred = 4026368 (3d7000 hex) > U-Boot> tftp 21400000 uImage.buildroot-20080620 > TFTP from server 192.168.1.2; our IP address is 192.168.1.3 > Filename 'uImage.buildroot-20080620'. > Load address: 0x21400000 > Loading: > ################################################################# > ################################################################# > ################################################################# > ###### > done > Bytes transferred = 1025408 (fa580 hex) > U-Boot> bootm > ## Booting image at 21400000 ... > Image Name: Linux-2.6.22.1 > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 1025344 Bytes = 1001.3 kB > Load Address: 20008000 > Entry Point: 20008000 > Verifying Checksum ... OK > OK > > Starting kernel ... > > Uncompressing > Linux.................................................................... > done, booting the kernel. > Linux version 2.6.22.1 (mike at himalia) (gcc version 4.2.4) #1 Fri Jun > 20 16:53:37 EDT 2008 > CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 > Machine: Atmel AT91SAM9260-EK > Memory policy: ECC disabled, Data cache writeback > Clocks: CPU 198 MHz, master 99 MHz, main 18.432 MHz > CPU0: D VIVT write-back cache > CPU0: I cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets > CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets > Built 1 zonelists. Total pages: 16256 > Kernel command line: mem=64M console=ttyS0,115200 > initrd=0x21100000,3145728 root=/dev/ram0 rw > AT91: 96 gpio irqs in 3 banks > PID hash table entries: 256 (order: 8, 1024 bytes) > Console: colour dummy device 80x30 > Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) > Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) > Memory: 64MB = 64MB total > Memory: 59648KB available (1856K code, 188K data, 100K init) > Mount-cache hash table entries: 512 > CPU: Testing write buffer coherency: ok > NET: Registered protocol family 16 > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > NET: Registered protocol family 2 > IP route cache hash table entries: 1024 (order: 0, 4096 bytes) > TCP established hash table entries: 2048 (order: 2, 16384 bytes) > TCP bind hash table entries: 2048 (order: 1, 8192 bytes) > TCP: Hash tables configured (established 2048 bind 2048) > TCP reno registered > checking if image is initramfs...it isn't (bad gzip magic numbers); > looks like an initrd > Freeing initrd memory: 3072K > NetWinder Floating Point Emulator V0.97 (double precision) > io scheduler noop registered > io scheduler anticipatory registered (default) > atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL > atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL > atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL > RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize > usbmon: debugfs is not available > at91_ohci at91_ohci: AT91 OHCI > at91_ohci at91_ohci: new USB bus registered, assigned bus number 1 > at91_ohci at91_ohci: irq 20, io mem 0x00500000 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > udc: at91_udc version 3 May 2006 > mice: PS/2 mouse device common for all mice > TCP cubic registered > NET: Registered protocol family 1 > NET: Registered protocol family 17 > RAMDISK: ext2 filesystem found at block 0 > RAMDISK: Loading 3932KiB [1 disk] into ram disk... done. > VFS: Mounted root (ext2 filesystem). > Freeing init memory: 100K > Initializing random number generator... done. > Starting network... > ip: RTNETLINK answers: File exists > > > > Welcome to the Erik's uClibc development environment. > uclibc login: root > > Mike Mike, Thanks, The kernel command line came from "make at91sam9260dfc_defconfig", but it was the problem. When my kernel was expanded @ 20008000 by u-boot it overran the start of the root filesystem @ 20410000. Additionally, my root fs was bigger than the ramdisk size (that's the 2nd parameter in the initrd command (3072K or 3145728)). So now that I've fixed those and have u-boot w/ the proper addresses, I can boot linux. Joe ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2008-06-23 16:48 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <mailman.1147.1213963958.1345.buildroot@uclibc.org>
2008-06-20 15:03 ` [Buildroot] can't find root fs kernel panic Joseph G. Boike
2008-06-20 19:32 ` Peter Korsgaard
2008-06-20 20:48 ` Thiago A. Corrêa
2008-06-21 2:28 ` [Buildroot] can t " Mike Sander
[not found] ` <485C66DD.2070304@ripnet.com>
2008-06-23 16:48 ` Joseph G. Boike
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox