* [Buildroot] glibc support
@ 2009-01-23 22:37 Dan Lykowski
2009-01-24 6:43 ` Peter Korsgaard
0 siblings, 1 reply; 6+ messages in thread
From: Dan Lykowski @ 2009-01-23 22:37 UTC (permalink / raw)
To: buildroot
I was the person who submitted the glibc patch in December.
No one ever commented so I have never pursued the matter.
I made the changes because I need to run fglrx ( closed source ATI driver )
for 3D performance reasons.
If there is interest, I can create the patch again.
Dan Lykowski
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.busybox.net/pipermail/buildroot/attachments/20090123/f70c3dfe/attachment.htm
^ permalink raw reply [flat|nested] 6+ messages in thread
* [Buildroot] glibc support
@ 2010-01-19 22:29 Matthew Davison
2010-01-20 6:46 ` Joachim Pihl
2010-01-20 9:07 ` Anders Darander
0 siblings, 2 replies; 6+ messages in thread
From: Matthew Davison @ 2010-01-19 22:29 UTC (permalink / raw)
To: buildroot
Is building with glibc instead of uClibc currently supported in
buildroot? If so, what steps are required?
Thanks for your help.
Matt
**********************************************************************
This e-mail is the property of Lantronix. It is intended only for the person or entity to which it is addressed and may contain information that is privileged, confidential, or otherwise protected from disclosure. Distribution or copying of this e-mail, or the information contained herein, to anyone other than the intended recipient is prohibited.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20100119/ffc015d2/attachment.htm>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [Buildroot] glibc support
2010-01-19 22:29 Matthew Davison
@ 2010-01-20 6:46 ` Joachim Pihl
2010-01-20 9:07 ` Anders Darander
1 sibling, 0 replies; 6+ messages in thread
From: Joachim Pihl @ 2010-01-20 6:46 UTC (permalink / raw)
To: buildroot
On Tue, 19 Jan 2010 23:29:09 +0100, Matthew Davison
<matt.davison@lantronix.com> wrote:
> Is building with glibc instead of uClibc currently supported in
> buildroot? If so, what steps are required?
>
> Thanks for your help.
I _think_ buildroot is tied in with uClibc pretty tight, but I'd like to
utter a "me too" if the process of integrating crosstool-ng makes the use
of EGLIBC with buildroot possible.
--
Joachim Pihl
Senior R&D Engineer
Nevion
Tel: +47 33 48 94 66
Fax: +47 33 48 99 98
Mobile: +47 91 33 98 91
jpihl at nevion.com
www.nevion.com
-----------------------------------
The Global Video Transport Leader
-----------------------------------
^ permalink raw reply [flat|nested] 6+ messages in thread
* [Buildroot] glibc support
2010-01-19 22:29 Matthew Davison
2010-01-20 6:46 ` Joachim Pihl
@ 2010-01-20 9:07 ` Anders Darander
2010-01-21 0:06 ` Matthew Davison
1 sibling, 1 reply; 6+ messages in thread
From: Anders Darander @ 2010-01-20 9:07 UTC (permalink / raw)
To: buildroot
Hi Matt,
On Tue, Jan 19, 2010 at 23:29, Matthew Davison
<matt.davison@lantronix.com> wrote:
> Is building with glibc instead of uClibc currently supported in buildroot?
> If so, what steps are required?
I've done this in a few projects. What I did (and I suppose everyone
else) is to build the cross-toolchain and glibc using crosstool-NG.
Then this toolchain can be used as an external toolchain in buildroot,
together with the glibc that you build. It is mostly pretty
straightforward.
Regards,
Anders
^ permalink raw reply [flat|nested] 6+ messages in thread
* [Buildroot] glibc support
2010-01-20 9:07 ` Anders Darander
@ 2010-01-21 0:06 ` Matthew Davison
0 siblings, 0 replies; 6+ messages in thread
From: Matthew Davison @ 2010-01-21 0:06 UTC (permalink / raw)
To: buildroot
Thanks for your help. I followed your advice and successfully built a
toolchain with crosstool-NG, and configured it as my external toolchain
in buildroot. I spent a little time getting the buildroot's toolchain
configuration options to match those of my new toolchain, but this was
fairly simple, and mostly a process of trial and error. Once my
toolchain configuration options were correct, the resulting build was
successful.
Matt
-----Original Message-----
From: Anders Darander [mailto:anders.darander at gmail.com]
Sent: Wednesday, January 20, 2010 1:08 AM
To: Matthew Davison
Cc: buildroot at busybox.net
Subject: Re: [Buildroot] glibc support
Hi Matt,
On Tue, Jan 19, 2010 at 23:29, Matthew Davison
<matt.davison@lantronix.com> wrote:
> Is building with glibc instead of uClibc currently supported in
buildroot?
> If so, what steps are required?
I've done this in a few projects. What I did (and I suppose everyone
else) is to build the cross-toolchain and glibc using crosstool-NG.
Then this toolchain can be used as an external toolchain in buildroot,
together with the glibc that you build. It is mostly pretty
straightforward.
Regards,
Anders
**********************************************************************
This e-mail is the property of Lantronix. It is intended only for the person or entity to which it is addressed and may contain information that is privileged, confidential, or otherwise protected from disclosure. Distribution or copying of this e-mail, or the information contained herein, to anyone other than the intended recipient is prohibited.
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2010-01-21 0:06 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-01-23 22:37 [Buildroot] glibc support Dan Lykowski
2009-01-24 6:43 ` Peter Korsgaard
-- strict thread matches above, loose matches on Subject: below --
2010-01-19 22:29 Matthew Davison
2010-01-20 6:46 ` Joachim Pihl
2010-01-20 9:07 ` Anders Darander
2010-01-21 0:06 ` Matthew Davison
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox