* [v3,4/5] dmaengine: xilinx_dma: autodetect whether the HW supports scatter-gather
@ 2018-06-29 7:37 Vinod Koul
0 siblings, 0 replies; 3+ messages in thread
From: Vinod Koul @ 2018-06-29 7:37 UTC (permalink / raw)
To: Andrea Merello
Cc: dan.j.williams, michal.simek, appana.durga.rao, dmaengine,
linux-arm-kernel, linux-kernel, Rob Herring, Mark Rutland,
devicetree, Radhey Shyam Pandey
On 25-06-18, 11:27, Andrea Merello wrote:
> The AXIDMA and CDMA HW can be either direct-access or scatter-gather
> version. These are SW incompatible.
>
> The driver can handle both version: a DT property was used to
^^^^
versions
> tell the driver whether to assume the HW is is scatter-gather mode.
^^^^^
is in?
>
> This patch makes the driver to autodetect this information. The DT
> property is not required anymore.
>
> No changes for VDMA.
>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Mark Rutland <mark.rutland@arm.com>
> Cc: devicetree@vger.kernel.org
> Cc: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
> Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
> ---
> Changes in v2:
> - autodetect only in !VDMA case
> Changes in v3:
> - cc DT maintainers/ML
> ---
> drivers/dma/xilinx/xilinx_dma.c | 14 ++++++++++----
> 1 file changed, 10 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/dma/xilinx/xilinx_dma.c b/drivers/dma/xilinx/xilinx_dma.c
> index 7f0ab904b749..43fcc71ff287 100644
> --- a/drivers/dma/xilinx/xilinx_dma.c
> +++ b/drivers/dma/xilinx/xilinx_dma.c
> @@ -86,6 +86,7 @@
> #define XILINX_DMA_DMASR_DMA_DEC_ERR BIT(6)
> #define XILINX_DMA_DMASR_DMA_SLAVE_ERR BIT(5)
> #define XILINX_DMA_DMASR_DMA_INT_ERR BIT(4)
> +#define XILINX_DMA_DMASR_SG_MASK BIT(3)
> #define XILINX_DMA_DMASR_IDLE BIT(1)
> #define XILINX_DMA_DMASR_HALTED BIT(0)
> #define XILINX_DMA_DMASR_DELAY_MASK GENMASK(31, 24)
> @@ -406,7 +407,6 @@ struct xilinx_dma_config {
> * @dev: Device Structure
> * @common: DMA device structure
> * @chan: Driver specific DMA channel
> - * @has_sg: Specifies whether Scatter-Gather is present or not
> * @mcdma: Specifies whether Multi-Channel is present or not
> * @flush_on_fsync: Flush on frame sync
> * @ext_addr: Indicates 64 bit addressing is supported by dma device
> @@ -426,7 +426,6 @@ struct xilinx_dma_device {
> struct device *dev;
> struct dma_device common;
> struct xilinx_dma_chan *chan[XILINX_DMA_MAX_CHANS_PER_DEVICE];
> - bool has_sg;
> bool mcdma;
> u32 flush_on_fsync;
> bool ext_addr;
> @@ -2393,7 +2392,6 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
>
> chan->dev = xdev->dev;
> chan->xdev = xdev;
> - chan->has_sg = xdev->has_sg;
> chan->desc_pendingcount = 0x0;
> chan->ext_addr = xdev->ext_addr;
> /* This variable ensures that descriptors are not
> @@ -2486,6 +2484,15 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
> chan->stop_transfer = xilinx_dma_stop_transfer;
> }
>
> + /* check if SG is enabled (only for AXIDMA and CDMA) */
> + if (xdev->dma_config->dmatype != XDMA_TYPE_VDMA) {
> + if (dma_ctrl_read(chan, XILINX_DMA_REG_DMASR) &
> + XILINX_DMA_DMASR_SG_MASK)
why not read this for VDMA too, will it return false?
> + chan->has_sg = true;
> + dev_dbg(chan->dev, "ch %d: SG %s\n", chan->id,
> + chan->has_sg ? "enabled" : "disabled");
this debug print can be removed
^ permalink raw reply [flat|nested] 3+ messages in thread* [v3,4/5] dmaengine: xilinx_dma: autodetect whether the HW supports scatter-gather
@ 2018-06-29 7:53 Andrea Merello
0 siblings, 0 replies; 3+ messages in thread
From: Andrea Merello @ 2018-06-29 7:53 UTC (permalink / raw)
To: Vinod
Cc: dan.j.williams, michal.simek, appana.durga.rao, dmaengine,
linux-arm-kernel, linux-kernel, Rob Herring, Mark Rutland,
devicetree, Radhey Shyam Pandey
On Fri, Jun 29, 2018 at 9:37 AM, Vinod <vkoul@kernel.org> wrote:
> On 25-06-18, 11:27, Andrea Merello wrote:
>> The AXIDMA and CDMA HW can be either direct-access or scatter-gather
>> version. These are SW incompatible.
>>
>> The driver can handle both version: a DT property was used to
> ^^^^
> versions
>
OK
>> tell the driver whether to assume the HW is is scatter-gather mode.
> ^^^^^
> is in?
Yes, it is. Thanks
>>
>> This patch makes the driver to autodetect this information. The DT
>> property is not required anymore.
>>
>> No changes for VDMA.
>>
>> Cc: Rob Herring <robh+dt@kernel.org>
>> Cc: Mark Rutland <mark.rutland@arm.com>
>> Cc: devicetree@vger.kernel.org
>> Cc: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
>> Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
>> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
>> ---
>> Changes in v2:
>> - autodetect only in !VDMA case
>> Changes in v3:
>> - cc DT maintainers/ML
>> ---
>> drivers/dma/xilinx/xilinx_dma.c | 14 ++++++++++----
>> 1 file changed, 10 insertions(+), 4 deletions(-)
>>
>> diff --git a/drivers/dma/xilinx/xilinx_dma.c b/drivers/dma/xilinx/xilinx_dma.c
>> index 7f0ab904b749..43fcc71ff287 100644
>> --- a/drivers/dma/xilinx/xilinx_dma.c
>> +++ b/drivers/dma/xilinx/xilinx_dma.c
>> @@ -86,6 +86,7 @@
>> #define XILINX_DMA_DMASR_DMA_DEC_ERR BIT(6)
>> #define XILINX_DMA_DMASR_DMA_SLAVE_ERR BIT(5)
>> #define XILINX_DMA_DMASR_DMA_INT_ERR BIT(4)
>> +#define XILINX_DMA_DMASR_SG_MASK BIT(3)
>> #define XILINX_DMA_DMASR_IDLE BIT(1)
>> #define XILINX_DMA_DMASR_HALTED BIT(0)
>> #define XILINX_DMA_DMASR_DELAY_MASK GENMASK(31, 24)
>> @@ -406,7 +407,6 @@ struct xilinx_dma_config {
>> * @dev: Device Structure
>> * @common: DMA device structure
>> * @chan: Driver specific DMA channel
>> - * @has_sg: Specifies whether Scatter-Gather is present or not
>> * @mcdma: Specifies whether Multi-Channel is present or not
>> * @flush_on_fsync: Flush on frame sync
>> * @ext_addr: Indicates 64 bit addressing is supported by dma device
>> @@ -426,7 +426,6 @@ struct xilinx_dma_device {
>> struct device *dev;
>> struct dma_device common;
>> struct xilinx_dma_chan *chan[XILINX_DMA_MAX_CHANS_PER_DEVICE];
>> - bool has_sg;
>> bool mcdma;
>> u32 flush_on_fsync;
>> bool ext_addr;
>> @@ -2393,7 +2392,6 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
>>
>> chan->dev = xdev->dev;
>> chan->xdev = xdev;
>> - chan->has_sg = xdev->has_sg;
>> chan->desc_pendingcount = 0x0;
>> chan->ext_addr = xdev->ext_addr;
>> /* This variable ensures that descriptors are not
>> @@ -2486,6 +2484,15 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
>> chan->stop_transfer = xilinx_dma_stop_transfer;
>> }
>>
>> + /* check if SG is enabled (only for AXIDMA and CDMA) */
>> + if (xdev->dma_config->dmatype != XDMA_TYPE_VDMA) {
>> + if (dma_ctrl_read(chan, XILINX_DMA_REG_DMASR) &
>> + XILINX_DMA_DMASR_SG_MASK)
>
> why not read this for VDMA too, will it return false?
AFAIK this bit is reserved in VDMA, so reading it can lead to any
random thing.. I would say that potentially it could even be used for
other purposes in future IP releases..
>> + chan->has_sg = true;
>> + dev_dbg(chan->dev, "ch %d: SG %s\n", chan->id,
>> + chan->has_sg ? "enabled" : "disabled");
>
> this debug print can be removed
IMHO if someone will ever enable debug prints for debugging something
and then he/she reports us a log, then it would be useful to see in
the log if the IP was SG or not..
> --
> ~Vinod
---
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 3+ messages in thread* [v3,4/5] dmaengine: xilinx_dma: autodetect whether the HW supports scatter-gather
@ 2018-06-25 9:27 Andrea Merello
0 siblings, 0 replies; 3+ messages in thread
From: Andrea Merello @ 2018-06-25 9:27 UTC (permalink / raw)
To: vkoul, dan.j.williams, michal.simek, appana.durga.rao, dmaengine
Cc: linux-arm-kernel, linux-kernel, Andrea Merello, Rob Herring,
Mark Rutland, devicetree, Radhey Shyam Pandey
The AXIDMA and CDMA HW can be either direct-access or scatter-gather
version. These are SW incompatible.
The driver can handle both version: a DT property was used to
tell the driver whether to assume the HW is is scatter-gather mode.
This patch makes the driver to autodetect this information. The DT
property is not required anymore.
No changes for VDMA.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
---
Changes in v2:
- autodetect only in !VDMA case
Changes in v3:
- cc DT maintainers/ML
---
drivers/dma/xilinx/xilinx_dma.c | 14 ++++++++++----
1 file changed, 10 insertions(+), 4 deletions(-)
diff --git a/drivers/dma/xilinx/xilinx_dma.c b/drivers/dma/xilinx/xilinx_dma.c
index 7f0ab904b749..43fcc71ff287 100644
--- a/drivers/dma/xilinx/xilinx_dma.c
+++ b/drivers/dma/xilinx/xilinx_dma.c
@@ -86,6 +86,7 @@
#define XILINX_DMA_DMASR_DMA_DEC_ERR BIT(6)
#define XILINX_DMA_DMASR_DMA_SLAVE_ERR BIT(5)
#define XILINX_DMA_DMASR_DMA_INT_ERR BIT(4)
+#define XILINX_DMA_DMASR_SG_MASK BIT(3)
#define XILINX_DMA_DMASR_IDLE BIT(1)
#define XILINX_DMA_DMASR_HALTED BIT(0)
#define XILINX_DMA_DMASR_DELAY_MASK GENMASK(31, 24)
@@ -406,7 +407,6 @@ struct xilinx_dma_config {
* @dev: Device Structure
* @common: DMA device structure
* @chan: Driver specific DMA channel
- * @has_sg: Specifies whether Scatter-Gather is present or not
* @mcdma: Specifies whether Multi-Channel is present or not
* @flush_on_fsync: Flush on frame sync
* @ext_addr: Indicates 64 bit addressing is supported by dma device
@@ -426,7 +426,6 @@ struct xilinx_dma_device {
struct device *dev;
struct dma_device common;
struct xilinx_dma_chan *chan[XILINX_DMA_MAX_CHANS_PER_DEVICE];
- bool has_sg;
bool mcdma;
u32 flush_on_fsync;
bool ext_addr;
@@ -2393,7 +2392,6 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
chan->dev = xdev->dev;
chan->xdev = xdev;
- chan->has_sg = xdev->has_sg;
chan->desc_pendingcount = 0x0;
chan->ext_addr = xdev->ext_addr;
/* This variable ensures that descriptors are not
@@ -2486,6 +2484,15 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
chan->stop_transfer = xilinx_dma_stop_transfer;
}
+ /* check if SG is enabled (only for AXIDMA and CDMA) */
+ if (xdev->dma_config->dmatype != XDMA_TYPE_VDMA) {
+ if (dma_ctrl_read(chan, XILINX_DMA_REG_DMASR) &
+ XILINX_DMA_DMASR_SG_MASK)
+ chan->has_sg = true;
+ dev_dbg(chan->dev, "ch %d: SG %s\n", chan->id,
+ chan->has_sg ? "enabled" : "disabled");
+ }
+
/* Initialize the tasklet */
tasklet_init(&chan->tasklet, xilinx_dma_do_tasklet,
(unsigned long)chan);
@@ -2624,7 +2631,6 @@ static int xilinx_dma_probe(struct platform_device *pdev)
return PTR_ERR(xdev->regs);
/* Retrieve the DMA engine properties from the device tree */
- xdev->has_sg = of_property_read_bool(node, "xlnx,include-sg");
xdev->max_buffer_len = GENMASK(XILINX_DMA_MAX_TRANS_LEN_MAX - 1, 0);
if (xdev->dma_config->dmatype == XDMA_TYPE_AXIDMA) {
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2018-06-29 7:53 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2018-06-29 7:37 [v3,4/5] dmaengine: xilinx_dma: autodetect whether the HW supports scatter-gather Vinod Koul
-- strict thread matches above, loose matches on Subject: below --
2018-06-29 7:53 Andrea Merello
2018-06-25 9:27 Andrea Merello
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox