From: sashiko-bot@kernel.org
To: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: lee@kernel.org, robh@kernel.org, conor+dt@kernel.org,
devicetree@vger.kernel.org, dri-devel@lists.freedesktop.org,
mfd@lists.linux.dev
Subject: Re: [PATCH 01/16] dt-bindings: twl-regulator: Add bindings for exposing ti, twl4030-regen
Date: Sat, 11 Jul 2026 06:10:10 +0000 [thread overview]
Message-ID: <20260711061010.AB35D1F00A3A@smtp.kernel.org> (raw)
In-Reply-To: <00718b18253a764c2a7c9a2b95c3b8c411796583.1783749722.git.hns@goldelico.com>
Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
- [Medium] The binding schema fails to enforce the required properties for the `ti,twl4030-regen` compatible string and rejects the `startup-delay-us` property.
- [Low] The commit message contains misspellings and an incorrect hardware model number.
--
--- Patch [1]: [PATCH 01/16] dt-bindings: twl-regulator: Add bindings for exposing ti,twl4030-regen ---
commit 47a2b827603c26c697c09f74aba57400724a478c
Author: Grond <grond66@riseup.net>
dt-bindings: twl-regulator: Add bindings for exposing ti,twl4030-regen
This commit adds the ti,twl4030-regen compatible string to the bindings. It
also updates the commit message to document its newly required regulator
properties.
> +Reguired properties:
> +For twl3040 REGEN signal:
[Severity: Low]
This isn't a bug, but should "Reguired" be "Required" and "twl3040" be
"twl4030"?
> diff --git a/Documentation/devicetree/bindings/mfd/ti,twl.yaml b/Documentation/devicetree/bindings/mfd/ti,twl.yaml
> index 9cc3e4721612e..183fc015e40ad 100644
> --- a/Documentation/devicetree/bindings/mfd/ti,twl.yaml
> +++ b/Documentation/devicetree/bindings/mfd/ti,twl.yaml
> @@ -46,6 +46,7 @@ allOf:
> - ti,twl4030-vusb1v5
> - ti,twl4030-vusb1v8
> - ti,twl4030-vusb3v1
> + - ti,twl4030-regen
> ti,retain-on-reset: false
>
> properties:
[Severity: Medium]
Will this schema allow validation to pass without the properties described in
the commit message?
Since there is no corresponding if-then block added to enforce
regulator-min-microvolt and regulator-max-microvolt, they won't be required
for ti,twl4030-regen.
Also, does this cause validation to fail when startup-delay-us is used?
Because startup-delay-us is not defined in the base regulator schema and
unevaluatedProperties is set to false for the regulator pattern block, any
device tree attempting to use startup-delay-us as instructed will likely be
rejected during dt_binding_check and dtbs_check.
--
Sashiko AI review · https://sashiko.dev/#/patchset/cover.1783749722.git.hns@goldelico.com?part=1
next prev parent reply other threads:[~2026-07-11 6:10 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-07-11 6:01 [PATCH 00/16] ARM: omap3: pandora: Modernize audio and backlight to Device Tree to finally remove pdata-quirks H. Nikolaus Schaller
2026-07-11 6:01 ` [PATCH 01/16] dt-bindings: twl-regulator: Add bindings for exposing ti, twl4030-regen H. Nikolaus Schaller
2026-07-11 6:10 ` sashiko-bot [this message]
2026-07-11 6:01 ` [PATCH 02/16] regulator: twl: Expose the TWL4030's REGEN signal as a regulator H. Nikolaus Schaller
2026-07-11 6:16 ` sashiko-bot
2026-07-11 6:01 ` [PATCH 03/16] arm: dts: twl4030: add twl4030-regen child H. Nikolaus Schaller
2026-07-11 6:18 ` sashiko-bot
2026-07-11 6:01 ` [PATCH 04/16] arm: dts: omap3pandora: Populate DT data for the TWL4030's REGEN regulator H. Nikolaus Schaller
2026-07-11 6:19 ` sashiko-bot
2026-07-11 6:01 ` [PATCH 05/16] arm: dts: omap3pandora: Don't use DMA channels for unused SPI masters H. Nikolaus Schaller
2026-07-11 6:06 ` sashiko-bot
2026-07-11 6:01 ` [PATCH 06/16] ASoC: twl4030-codec: Allow setting APLL rate through the .set_sysclk() interface H. Nikolaus Schaller
2026-07-11 6:12 ` sashiko-bot
2026-07-11 6:01 ` [PATCH 07/16] ASoC: dt-bindings: add TI PCM1773 H. Nikolaus Schaller
2026-07-11 6:08 ` sashiko-bot
2026-07-11 7:39 ` Rob Herring (Arm)
2026-07-11 6:01 ` [PATCH 08/16] ASoC: pcm1773-codec: write a driver for the PCM1773 chip from TI H. Nikolaus Schaller
2026-07-11 6:14 ` sashiko-bot
2026-07-11 6:01 ` [PATCH 09/16] ASoC: dt-bindings: add OpenPandora Sound Card H. Nikolaus Schaller
2026-07-11 6:10 ` sashiko-bot
2026-07-11 7:39 ` Rob Herring (Arm)
2026-07-11 6:01 ` [PATCH 10/16] ASoC: omap3pandora: Rewrite sound card driver as a platform driver with DT H. Nikolaus Schaller
2026-07-11 6:15 ` sashiko-bot
2026-07-11 6:01 ` [PATCH 11/16] ARM: dts: omap3-pandora-common: Enable audio in/out (mcbsp4/2) H. Nikolaus Schaller
2026-07-11 6:17 ` sashiko-bot
2026-07-11 6:01 ` [PATCH 12/16] arm: dts: omap3pandora: Add device node for PCM1773 codec H. Nikolaus Schaller
2026-07-11 6:15 ` sashiko-bot
2026-07-11 6:02 ` [PATCH 13/16] arm: dts: omap3pandora: create new DT node for the sound card H. Nikolaus Schaller
2026-07-11 6:17 ` sashiko-bot
2026-07-11 6:02 ` [PATCH 14/16] arm: dts: omap3-pandora-common: backlight: switch to twl4030 pwm and pwm_bl H. Nikolaus Schaller
2026-07-11 6:15 ` sashiko-bot
2026-07-11 6:02 ` [PATCH 15/16] backlight: remove pandora_bl H. Nikolaus Schaller
2026-07-11 6:16 ` sashiko-bot
2026-07-11 6:02 ` [PATCH 16/16] arm: omap2: remove remaining pdata-quirks for pandora legacy devices H. Nikolaus Schaller
2026-07-11 6:13 ` sashiko-bot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260711061010.AB35D1F00A3A@smtp.kernel.org \
--to=sashiko-bot@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=hns@goldelico.com \
--cc=lee@kernel.org \
--cc=mfd@lists.linux.dev \
--cc=robh@kernel.org \
--cc=sashiko-reviews@lists.linux.dev \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox