From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
To: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Subject: Re: [PATCH 1/5] drm/rcar-du: Use drm_mode_get_hv_timing() to populate plane clip rectangle
Date: Wed, 24 Jan 2018 02:07:30 +0200 [thread overview]
Message-ID: <3491323.Vvjl2Tpm6D@avalon> (raw)
In-Reply-To: <20180123170857.13818-1-ville.syrjala@linux.intel.com>
Hi Ville,
Thank you for the patch.
On Tuesday, 23 January 2018 19:08:53 EET Ville Syrjala wrote:
> From: Ville Syrjälä <ville.syrjala@linux.intel.com>
>
> Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
>
> No functional changes as the code already uses crtc_state->mode
> to populate the clip, which is also what drm_mode_get_hv_timing()
> uses.
>
> Once everyone agrees on this we can move the clip handling into
> drm_atomic_helper_check_plane_state().
>
> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
> ---
> drivers/gpu/drm/rcar-du/rcar_du_plane.c | 9 ++++-----
> 1 file changed, 4 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/gpu/drm/rcar-du/rcar_du_plane.c
> b/drivers/gpu/drm/rcar-du/rcar_du_plane.c index 4a3d16cf3ed6..5687a94d4cb1
> 100644
> --- a/drivers/gpu/drm/rcar-du/rcar_du_plane.c
> +++ b/drivers/gpu/drm/rcar-du/rcar_du_plane.c
> @@ -572,7 +572,7 @@ int __rcar_du_plane_atomic_check(struct drm_plane
> *plane, {
> struct drm_device *dev = plane->dev;
> struct drm_crtc_state *crtc_state;
> - struct drm_rect clip;
> + struct drm_rect clip = {};
Nitpicking, isn't the correct C99 zero initializer { 0 } ? I doesn't matter
too much as the variable is removed in patch 5/5 but we could as well fix it
if needed.
Apart from that,
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> int ret;
>
> if (!state->crtc) {
> @@ -589,10 +589,9 @@ int __rcar_du_plane_atomic_check(struct drm_plane
> *plane, if (IS_ERR(crtc_state))
> return PTR_ERR(crtc_state);
>
> - clip.x1 = 0;
> - clip.y1 = 0;
> - clip.x2 = crtc_state->mode.hdisplay;
> - clip.y2 = crtc_state->mode.vdisplay;
> + if (crtc_state->enable)
> + drm_mode_get_hv_timing(&crtc_state->mode,
> + &clip.x2, &clip.y2);
>
> ret = drm_atomic_helper_check_plane_state(state, crtc_state, &clip,
> DRM_PLANE_HELPER_NO_SCALING,
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
next prev parent reply other threads:[~2018-01-24 0:07 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-23 17:08 [PATCH 1/5] drm/rcar-du: Use drm_mode_get_hv_timing() to populate plane clip rectangle Ville Syrjala
2018-01-23 17:08 ` [PATCH 2/5] drm/sun4i: " Ville Syrjala
2018-02-02 15:04 ` Ville Syrjälä
2018-01-23 17:08 ` [PATCH 3/5] drm/armada: Construct a temporary crtc state for plane checks Ville Syrjala
2018-01-23 18:42 ` Russell King - ARM Linux
2018-01-23 19:02 ` Ville Syrjälä
2018-02-02 14:10 ` Ville Syrjälä
2018-02-02 15:10 ` Ville Syrjälä
2018-02-23 15:55 ` Ville Syrjälä
2018-02-23 19:14 ` Russell King - ARM Linux
2018-01-23 17:08 ` [PATCH 4/5] drm/armada: Use drm_mode_get_hv_timing() to populate plane clip rectangle Ville Syrjala
2018-03-05 8:41 ` Daniel Vetter
2018-03-05 18:58 ` Ville Syrjälä
2018-01-23 17:08 ` [PATCH 5/5] drm: Don't pass clip to drm_atomic_helper_check_plane_state() Ville Syrjala
2018-01-23 18:06 ` Philipp Zabel
2018-01-24 0:12 ` Laurent Pinchart
2018-01-24 19:48 ` Sinclair Yeh
[not found] ` <20180123170857.13818-5-ville.syrjala-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
2018-01-23 17:46 ` Liviu Dudau
2018-01-26 5:23 ` Neil Armstrong
2018-02-05 6:50 ` Shawn Guo
2018-01-24 0:07 ` Laurent Pinchart [this message]
2018-01-24 15:01 ` [PATCH 1/5] drm/rcar-du: Use drm_mode_get_hv_timing() to populate plane clip rectangle Ville Syrjälä
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3491323.Vvjl2Tpm6D@avalon \
--to=laurent.pinchart@ideasonboard.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=ville.syrjala@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox