[PATCH AUTOSEL 6.14 108/642] i3c: master: svc: Fix missing STOP for master request

[PATCH AUTOSEL 6.14 108/642] i3c: master: svc: Fix missing STOP for master request

[Sasha Levin]

From: Stanley Chu <yschu@nuvoton.com>

[ Upstream commit 0430bf9bc1ac068c8b8c540eb93e5751872efc51 ]

The controller driver nacked the master request but didn't emit a
STOP to end the transaction. The driver shall refuse the unsupported
requests and return the controller state to IDLE by emitting a STOP.

Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250318053606.3087121-4-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/i3c/master/svc-i3c-master.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/i3c/master/svc-i3c-master.c b/drivers/i3c/master/svc-i3c-master.c
index 0fc03bb5d0a6e..a18fe62962b0c 100644
--- a/drivers/i3c/master/svc-i3c-master.c
+++ b/drivers/i3c/master/svc-i3c-master.c
@@ -551,6 +551,7 @@ static void svc_i3c_master_ibi_work(struct work_struct *work)
 			queue_work(master->base.wq, &master->hj_work);
 		break;
 	case SVC_I3C_MSTATUS_IBITYPE_MASTER_REQUEST:
+		svc_i3c_master_emit_stop(master);
 	default:
 		break;
 	}
-- 
2.39.5

[PATCH AUTOSEL 6.14 217/642] crypto: mxs-dcp - Only set OTP_KEY bit for OTP key

[Sasha Levin]

From: Sven Schwermer <sven@svenschwermer.de>

[ Upstream commit caa9dbb76ff52ec848a57245062aaeaa07740adc ]

While MXS_DCP_CONTROL0_OTP_KEY is set, the CRYPTO_KEY (DCP_PAES_KEY_OTP)
is used even if the UNIQUE_KEY (DCP_PAES_KEY_UNIQUE) is selected. This
is not clearly documented, but this implementation is consistent with
NXP's downstream kernel fork and optee_os.

Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/crypto/mxs-dcp.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/crypto/mxs-dcp.c b/drivers/crypto/mxs-dcp.c
index d94a26c3541a0..133ebc9982362 100644
--- a/drivers/crypto/mxs-dcp.c
+++ b/drivers/crypto/mxs-dcp.c
@@ -265,12 +265,12 @@ static int mxs_dcp_run_aes(struct dcp_async_ctx *actx,
 		    MXS_DCP_CONTROL0_INTERRUPT |
 		    MXS_DCP_CONTROL0_ENABLE_CIPHER;
 
-	if (key_referenced)
-		/* Set OTP key bit to select the key via KEY_SELECT. */
-		desc->control0 |= MXS_DCP_CONTROL0_OTP_KEY;
-	else
+	if (!key_referenced)
 		/* Payload contains the key. */
 		desc->control0 |= MXS_DCP_CONTROL0_PAYLOAD_KEY;
+	else if (actx->key[0] == DCP_PAES_KEY_OTP)
+		/* Set OTP key bit to select the key via KEY_SELECT. */
+		desc->control0 |= MXS_DCP_CONTROL0_OTP_KEY;
 
 	if (rctx->enc)
 		desc->control0 |= MXS_DCP_CONTROL0_CIPHER_ENCRYPT;
-- 
2.39.5

[PATCH AUTOSEL 6.14 281/642] clk: imx8mp: inform CCF of maximum frequency of clocks

[Sasha Levin]

From: Ahmad Fatoum <a.fatoum@pengutronix.de>

[ Upstream commit 06a61b5cb6a8638fa8823cd09b17233b29696fa2 ]

The IMX8MPCEC datasheet lists maximum frequencies allowed for different
modules. Some of these limits are universal, but some depend on
whether the SoC is operating in nominal or in overdrive mode.

The imx8mp.dtsi currently assumes overdrive mode and configures some
clocks in accordance with this. Boards wishing to make use of nominal
mode will need to override some of the clock rates manually.

As operating the clocks outside of their allowed range can lead to
difficult to debug issues, it makes sense to register the maximum rates
allowed in the driver, so the CCF can take them into account.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20250218-imx8m-clk-v4-6-b7697dc2dcd0@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/imx/clk-imx8mp.c | 151 +++++++++++++++++++++++++++++++++++
 1 file changed, 151 insertions(+)

diff --git a/drivers/clk/imx/clk-imx8mp.c b/drivers/clk/imx/clk-imx8mp.c
index fb18f507f1213..fe6dac70f1a15 100644
--- a/drivers/clk/imx/clk-imx8mp.c
+++ b/drivers/clk/imx/clk-imx8mp.c
@@ -8,6 +8,7 @@
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/module.h>
+#include <linux/units.h>
 #include <linux/of_address.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
@@ -406,11 +407,151 @@ static const char * const imx8mp_clkout_sels[] = {"audio_pll1_out", "audio_pll2_
 static struct clk_hw **hws;
 static struct clk_hw_onecell_data *clk_hw_data;
 
+struct imx8mp_clock_constraints {
+	unsigned int clkid;
+	u32 maxrate;
+};
+
+/*
+ * Below tables are taken from IMX8MPCEC Rev. 2.1, 07/2023
+ * Table 13. Maximum frequency of modules.
+ * Probable typos fixed are marked with a comment.
+ */
+static const struct imx8mp_clock_constraints imx8mp_clock_common_constraints[] = {
+	{ IMX8MP_CLK_A53_DIV,             1000 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ENET_AXI,             266666667 }, /* Datasheet claims 266MHz */
+	{ IMX8MP_CLK_NAND_USDHC_BUS,       266666667 }, /* Datasheet claims 266MHz */
+	{ IMX8MP_CLK_MEDIA_APB,            200 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_HDMI_APB,             133333333 }, /* Datasheet claims 133MHz */
+	{ IMX8MP_CLK_ML_AXI,               800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_AHB,                  133333333 },
+	{ IMX8MP_CLK_IPG_ROOT,              66666667 },
+	{ IMX8MP_CLK_AUDIO_AHB,            400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_DISP2_PIX,      170 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_DRAM_ALT,             666666667 },
+	{ IMX8MP_CLK_DRAM_APB,             200 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_CAN1,                  80 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_CAN2,                  80 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_PCIE_AUX,              10 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_I2C5,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_I2C6,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_SAI1,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_SAI2,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_SAI3,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_SAI5,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_SAI6,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_ENET_QOS,             125 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ENET_QOS_TIMER,       200 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ENET_REF,             125 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ENET_TIMER,           125 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ENET_PHY_REF,         125 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_NAND,                 500 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_QSPI,                 400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_USDHC1,               400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_USDHC2,               400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_I2C1,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_I2C2,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_I2C3,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_I2C4,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_UART1,                 80 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_UART2,                 80 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_UART3,                 80 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_UART4,                 80 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ECSPI1,                80 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ECSPI2,                80 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_PWM1,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_PWM2,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_PWM3,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_PWM4,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_GPT1,                 100 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPT2,                 100 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPT3,                 100 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPT4,                 100 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPT5,                 100 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPT6,                 100 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_WDOG,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_IPP_DO_CLKO1,         200 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_IPP_DO_CLKO2,         200 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_HDMI_REF_266M,        266 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_USDHC3,               400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_MIPI_PHY1_REF,  300 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_DISP1_PIX,      250 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_CAM2_PIX,       277 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_LDB,            595 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_MIPI_TEST_BYTE, 200 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ECSPI3,                80 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_PDM,                  200 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_SAI7,                  66666667 }, /* Datasheet claims 66MHz */
+	{ IMX8MP_CLK_MAIN_AXI,             400 * HZ_PER_MHZ },
+	{ /* Sentinel */ }
+};
+
+static const struct imx8mp_clock_constraints imx8mp_clock_nominal_constraints[] = {
+	{ IMX8MP_CLK_M7_CORE,           600 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ML_CORE,           800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU3D_CORE,        800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU3D_SHADER_CORE, 800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU2D_CORE,        800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_AUDIO_AXI_SRC,     600 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_HSIO_AXI,          400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_ISP,         400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_VPU_BUS,           600 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_AXI,         400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_HDMI_AXI,          400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU_AXI,           600 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU_AHB,           300 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_NOC,               800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_NOC_IO,            600 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ML_AHB,            300 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_VPU_G1,            600 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_VPU_G2,            500 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_CAM1_PIX,    400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_VPU_VC8000E,       400 * HZ_PER_MHZ }, /* Datasheet claims 500MHz */
+	{ IMX8MP_CLK_DRAM_CORE,         800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GIC,               400 * HZ_PER_MHZ },
+	{ /* Sentinel */ }
+};
+
+static const struct imx8mp_clock_constraints imx8mp_clock_overdrive_constraints[] = {
+	{ IMX8MP_CLK_M7_CORE,            800 * HZ_PER_MHZ},
+	{ IMX8MP_CLK_ML_CORE,           1000 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU3D_CORE,        1000 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU3D_SHADER_CORE, 1000 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU2D_CORE,        1000 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_AUDIO_AXI_SRC,      800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_HSIO_AXI,           500 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_ISP,          500 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_VPU_BUS,            800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_AXI,          500 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_HDMI_AXI,           500 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU_AXI,            800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GPU_AHB,            400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_NOC,               1000 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_NOC_IO,             800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_ML_AHB,             400 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_VPU_G1,             800 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_VPU_G2,             700 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_MEDIA_CAM1_PIX,     500 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_VPU_VC8000E,        500 * HZ_PER_MHZ }, /* Datasheet claims 400MHz */
+	{ IMX8MP_CLK_DRAM_CORE,         1000 * HZ_PER_MHZ },
+	{ IMX8MP_CLK_GIC,                500 * HZ_PER_MHZ },
+	{ /* Sentinel */ }
+};
+
+static void imx8mp_clocks_apply_constraints(const struct imx8mp_clock_constraints constraints[])
+{
+	const struct imx8mp_clock_constraints *constr;
+
+	for (constr = constraints; constr->clkid; constr++)
+		clk_hw_set_rate_range(hws[constr->clkid], 0, constr->maxrate);
+}
+
 static int imx8mp_clocks_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct device_node *np;
 	void __iomem *anatop_base, *ccm_base;
+	const char *opmode;
 	int err;
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx8mp-anatop");
@@ -715,6 +856,16 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)
 
 	imx_check_clk_hws(hws, IMX8MP_CLK_END);
 
+	imx8mp_clocks_apply_constraints(imx8mp_clock_common_constraints);
+
+	err = of_property_read_string(np, "fsl,operating-mode", &opmode);
+	if (!err) {
+		if (!strcmp(opmode, "nominal"))
+			imx8mp_clocks_apply_constraints(imx8mp_clock_nominal_constraints);
+		else if (!strcmp(opmode, "overdrive"))
+			imx8mp_clocks_apply_constraints(imx8mp_clock_overdrive_constraints);
+	}
+
 	err = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
 	if (err < 0) {
 		dev_err(dev, "failed to register hws for i.MX8MP\n");
-- 
2.39.5

[PATCH AUTOSEL 6.14 376/642] i3c: master: svc: Flush FIFO before sending Dynamic Address Assignment(DAA)

[Sasha Levin]

From: Frank Li <Frank.Li@nxp.com>

[ Upstream commit a892ee4cf22a50e1d6988d0464a9a421f3e5db2f ]

Ensure the FIFO is empty before issuing the DAA command to prevent
incorrect command data from being sent. Align with other data transfers,
such as svc_i3c_master_start_xfer_locked(), which flushes the FIFO before
sending a command.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250129162250.3629189-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/i3c/master/svc-i3c-master.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/i3c/master/svc-i3c-master.c b/drivers/i3c/master/svc-i3c-master.c
index a18fe62962b0c..2cf2c567f8931 100644
--- a/drivers/i3c/master/svc-i3c-master.c
+++ b/drivers/i3c/master/svc-i3c-master.c
@@ -899,6 +899,8 @@ static int svc_i3c_master_do_daa_locked(struct svc_i3c_master *master,
 	u32 reg;
 	int ret, i;
 
+	svc_i3c_master_flush_fifo(master);
+
 	while (true) {
 		/* clean SVC_I3C_MINT_IBIWON w1c bits */
 		writel(SVC_I3C_MINT_IBIWON, master->regs + SVC_I3C_MSTATUS);
-- 
2.39.5

[PATCH AUTOSEL 6.14 390/642] serial: mctrl_gpio: split disable_ms into sync and no_sync APIs

[Sasha Levin]

From: Alexis Lothoré <alexis.lothore@bootlin.com>

[ Upstream commit 1bd2aad57da95f7f2d2bb52f7ad15c0f4993a685 ]

The following splat has been observed on a SAMA5D27 platform using
atmel_serial:

BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last  enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last  enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
  unwind_backtrace from show_stack+0x18/0x1c
  show_stack from dump_stack_lvl+0x44/0x70
  dump_stack_lvl from __might_resched+0x38c/0x598
  __might_resched from disable_irq+0x1c/0x48
  disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
  mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
  atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
  atmel_set_termios from uart_change_line_settings+0x15c/0x994
  uart_change_line_settings from uart_set_termios+0x2b0/0x668
  uart_set_termios from tty_set_termios+0x600/0x8ec
  tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
  ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
  wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
  hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
  hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
  hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
  process_one_work from worker_thread+0x6e0/0xfb4
  worker_thread from kthread+0x3d4/0x484
  kthread from ret_from_fork+0x14/0x28

This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly.  The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).

Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock.

Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20250217-atomic_sleep_mctrl_serial_gpio-v3-1-59324b313eef@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 Documentation/driver-api/serial/driver.rst |  2 +-
 drivers/tty/serial/8250/8250_port.c        |  2 +-
 drivers/tty/serial/atmel_serial.c          |  2 +-
 drivers/tty/serial/imx.c                   |  2 +-
 drivers/tty/serial/serial_mctrl_gpio.c     | 34 +++++++++++++++++-----
 drivers/tty/serial/serial_mctrl_gpio.h     | 17 +++++++++--
 drivers/tty/serial/sh-sci.c                |  2 +-
 drivers/tty/serial/stm32-usart.c           |  2 +-
 8 files changed, 47 insertions(+), 16 deletions(-)

diff --git a/Documentation/driver-api/serial/driver.rst b/Documentation/driver-api/serial/driver.rst
index 84b43061c11be..60434f2b02863 100644
--- a/Documentation/driver-api/serial/driver.rst
+++ b/Documentation/driver-api/serial/driver.rst
@@ -103,4 +103,4 @@ Some helpers are provided in order to set/get modem control lines via GPIO.
 .. kernel-doc:: drivers/tty/serial/serial_mctrl_gpio.c
    :identifiers: mctrl_gpio_init mctrl_gpio_free mctrl_gpio_to_gpiod
            mctrl_gpio_set mctrl_gpio_get mctrl_gpio_enable_ms
-           mctrl_gpio_disable_ms
+           mctrl_gpio_disable_ms_sync mctrl_gpio_disable_ms_no_sync
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 442967a6cd52d..886e40f680d45 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1680,7 +1680,7 @@ static void serial8250_disable_ms(struct uart_port *port)
 	if (up->bugs & UART_BUG_NOMSR)
 		return;
 
-	mctrl_gpio_disable_ms(up->gpios);
+	mctrl_gpio_disable_ms_no_sync(up->gpios);
 
 	up->ier &= ~UART_IER_MSI;
 	serial_port_out(port, UART_IER, up->ier);
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index f44f9d20a9744..8918fbd4bddd5 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -700,7 +700,7 @@ static void atmel_disable_ms(struct uart_port *port)
 
 	atmel_port->ms_irq_enabled = false;
 
-	mctrl_gpio_disable_ms(atmel_port->gpios);
+	mctrl_gpio_disable_ms_no_sync(atmel_port->gpios);
 
 	if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
 		idr |= ATMEL_US_CTSIC;
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 9c59ec128bb4f..cfeb3f8cf45ea 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1608,7 +1608,7 @@ static void imx_uart_shutdown(struct uart_port *port)
 		imx_uart_dma_exit(sport);
 	}
 
-	mctrl_gpio_disable_ms(sport->gpios);
+	mctrl_gpio_disable_ms_sync(sport->gpios);
 
 	uart_port_lock_irqsave(&sport->port, &flags);
 	ucr2 = imx_uart_readl(sport, UCR2);
diff --git a/drivers/tty/serial/serial_mctrl_gpio.c b/drivers/tty/serial/serial_mctrl_gpio.c
index 8855688a5b6c0..ca55bcc0b6111 100644
--- a/drivers/tty/serial/serial_mctrl_gpio.c
+++ b/drivers/tty/serial/serial_mctrl_gpio.c
@@ -322,11 +322,7 @@ void mctrl_gpio_enable_ms(struct mctrl_gpios *gpios)
 }
 EXPORT_SYMBOL_GPL(mctrl_gpio_enable_ms);
 
-/**
- * mctrl_gpio_disable_ms - disable irqs and handling of changes to the ms lines
- * @gpios: gpios to disable
- */
-void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios)
+static void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios, bool sync)
 {
 	enum mctrl_gpio_idx i;
 
@@ -342,10 +338,34 @@ void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios)
 		if (!gpios->irq[i])
 			continue;
 
-		disable_irq(gpios->irq[i]);
+		if (sync)
+			disable_irq(gpios->irq[i]);
+		else
+			disable_irq_nosync(gpios->irq[i]);
 	}
 }
-EXPORT_SYMBOL_GPL(mctrl_gpio_disable_ms);
+
+/**
+ * mctrl_gpio_disable_ms_sync - disable irqs and handling of changes to the ms
+ * lines, and wait for any pending IRQ to be processed
+ * @gpios: gpios to disable
+ */
+void mctrl_gpio_disable_ms_sync(struct mctrl_gpios *gpios)
+{
+	mctrl_gpio_disable_ms(gpios, true);
+}
+EXPORT_SYMBOL_GPL(mctrl_gpio_disable_ms_sync);
+
+/**
+ * mctrl_gpio_disable_ms_no_sync - disable irqs and handling of changes to the
+ * ms lines, and return immediately
+ * @gpios: gpios to disable
+ */
+void mctrl_gpio_disable_ms_no_sync(struct mctrl_gpios *gpios)
+{
+	mctrl_gpio_disable_ms(gpios, false);
+}
+EXPORT_SYMBOL_GPL(mctrl_gpio_disable_ms_no_sync);
 
 void mctrl_gpio_enable_irq_wake(struct mctrl_gpios *gpios)
 {
diff --git a/drivers/tty/serial/serial_mctrl_gpio.h b/drivers/tty/serial/serial_mctrl_gpio.h
index fc76910fb105a..79e97838ebe56 100644
--- a/drivers/tty/serial/serial_mctrl_gpio.h
+++ b/drivers/tty/serial/serial_mctrl_gpio.h
@@ -87,9 +87,16 @@ void mctrl_gpio_free(struct device *dev, struct mctrl_gpios *gpios);
 void mctrl_gpio_enable_ms(struct mctrl_gpios *gpios);
 
 /*
- * Disable gpio interrupts to report status line changes.
+ * Disable gpio interrupts to report status line changes, and block until
+ * any corresponding IRQ is processed
  */
-void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios);
+void mctrl_gpio_disable_ms_sync(struct mctrl_gpios *gpios);
+
+/*
+ * Disable gpio interrupts to report status line changes, and return
+ * immediately
+ */
+void mctrl_gpio_disable_ms_no_sync(struct mctrl_gpios *gpios);
 
 /*
  * Enable gpio wakeup interrupts to enable wake up source.
@@ -148,7 +155,11 @@ static inline void mctrl_gpio_enable_ms(struct mctrl_gpios *gpios)
 {
 }
 
-static inline void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios)
+static inline void mctrl_gpio_disable_ms_sync(struct mctrl_gpios *gpios)
+{
+}
+
+static inline void mctrl_gpio_disable_ms_no_sync(struct mctrl_gpios *gpios)
 {
 }
 
diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index b1ea48f38248e..41f987632bce8 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -2298,7 +2298,7 @@ static void sci_shutdown(struct uart_port *port)
 	dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
 
 	s->autorts = false;
-	mctrl_gpio_disable_ms(to_sci_port(port)->gpios);
+	mctrl_gpio_disable_ms_sync(to_sci_port(port)->gpios);
 
 	uart_port_lock_irqsave(port, &flags);
 	sci_stop_rx(port);
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 0854ad8c90cd2..ad06b760cfca7 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -944,7 +944,7 @@ static void stm32_usart_enable_ms(struct uart_port *port)
 
 static void stm32_usart_disable_ms(struct uart_port *port)
 {
-	mctrl_gpio_disable_ms(to_stm32_port(port)->gpios);
+	mctrl_gpio_disable_ms_sync(to_stm32_port(port)->gpios);
 }
 
 /* Transmit stop */
-- 
2.39.5

[PATCH AUTOSEL 6.14 392/642] pmdomain: imx: gpcv2: use proper helper for property detection

[Sasha Levin]

From: Ahmad Fatoum <a.fatoum@pengutronix.de>

[ Upstream commit 6568cb40e73163fa25e2779f7234b169b2e1a32e ]

Starting with commit c141ecc3cecd7 ("of: Warn when of_property_read_bool()
is used on non-boolean properties"), probing the gpcv2 device on i.MX8M
SoCs leads to warnings when LOCKDEP is enabled.

Fix this by checking property presence with of_property_present as
intended.

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20250218-gpcv2-of-property-present-v1-1-3bb1a9789654@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pmdomain/imx/gpcv2.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/pmdomain/imx/gpcv2.c b/drivers/pmdomain/imx/gpcv2.c
index 958d34d4821b1..105fcaf13a34c 100644
--- a/drivers/pmdomain/imx/gpcv2.c
+++ b/drivers/pmdomain/imx/gpcv2.c
@@ -1361,7 +1361,7 @@ static int imx_pgc_domain_probe(struct platform_device *pdev)
 	}
 
 	if (IS_ENABLED(CONFIG_LOCKDEP) &&
-	    of_property_read_bool(domain->dev->of_node, "power-domains"))
+	    of_property_present(domain->dev->of_node, "power-domains"))
 		lockdep_set_subclass(&domain->genpd.mlock, 1);
 
 	ret = of_genpd_add_provider_simple(domain->dev->of_node,
-- 
2.39.5

[PATCH AUTOSEL 6.14 507/642] net: fec: Refactor MAC reset to function

[Sasha Levin]

From: Csókás, Bence <csokas.bence@prolan.hu>

[ Upstream commit 67800d296191d0a9bde0a7776f99ca1ddfa0fc26 ]

The core is reset both in `fec_restart()` (called on link-up) and
`fec_stop()` (going to sleep, driver remove etc.). These two functions
had their separate implementations, which was at first only a register
write and a `udelay()` (and the accompanying block comment). However,
since then we got soft-reset (MAC disable) and Wake-on-LAN support, which
meant that these implementations diverged, often causing bugs.

For instance, as of now, `fec_stop()` does not check for
`FEC_QUIRK_NO_HARD_RESET`, meaning the MII/RMII mode is cleared on eg.
a PM power-down event; and `fec_restart()` missed the refactor renaming
the "magic" constant `1` to `FEC_ECR_RESET`.

To harmonize current implementations, and eliminate this source of
potential future bugs, refactor implementation to a common function.

Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20250207121255.161146-2-csokas.bence@prolan.hu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/freescale/fec_main.c | 52 +++++++++++------------
 1 file changed, 25 insertions(+), 27 deletions(-)

diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index f7c4ce8e9a265..a86cfebedaa8b 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -1093,6 +1093,29 @@ static void fec_enet_enable_ring(struct net_device *ndev)
 	}
 }
 
+/* Whack a reset.  We should wait for this.
+ * For i.MX6SX SOC, enet use AXI bus, we use disable MAC
+ * instead of reset MAC itself.
+ */
+static void fec_ctrl_reset(struct fec_enet_private *fep, bool allow_wol)
+{
+	u32 val;
+
+	if (!allow_wol || !(fep->wol_flag & FEC_WOL_FLAG_SLEEP_ON)) {
+		if (fep->quirks & FEC_QUIRK_HAS_MULTI_QUEUES ||
+		    ((fep->quirks & FEC_QUIRK_NO_HARD_RESET) && fep->link)) {
+			writel(0, fep->hwp + FEC_ECNTRL);
+		} else {
+			writel(FEC_ECR_RESET, fep->hwp + FEC_ECNTRL);
+			udelay(10);
+		}
+	} else {
+		val = readl(fep->hwp + FEC_ECNTRL);
+		val |= (FEC_ECR_MAGICEN | FEC_ECR_SLEEP);
+		writel(val, fep->hwp + FEC_ECNTRL);
+	}
+}
+
 /*
  * This function is called to start or restart the FEC during a link
  * change, transmit timeout, or to reconfigure the FEC.  The network
@@ -1109,17 +1132,7 @@ fec_restart(struct net_device *ndev)
 	if (fep->bufdesc_ex)
 		fec_ptp_save_state(fep);
 
-	/* Whack a reset.  We should wait for this.
-	 * For i.MX6SX SOC, enet use AXI bus, we use disable MAC
-	 * instead of reset MAC itself.
-	 */
-	if (fep->quirks & FEC_QUIRK_HAS_MULTI_QUEUES ||
-	    ((fep->quirks & FEC_QUIRK_NO_HARD_RESET) && fep->link)) {
-		writel(0, fep->hwp + FEC_ECNTRL);
-	} else {
-		writel(1, fep->hwp + FEC_ECNTRL);
-		udelay(10);
-	}
+	fec_ctrl_reset(fep, false);
 
 	/*
 	 * enet-mac reset will reset mac address registers too,
@@ -1373,22 +1386,7 @@ fec_stop(struct net_device *ndev)
 	if (fep->bufdesc_ex)
 		fec_ptp_save_state(fep);
 
-	/* Whack a reset.  We should wait for this.
-	 * For i.MX6SX SOC, enet use AXI bus, we use disable MAC
-	 * instead of reset MAC itself.
-	 */
-	if (!(fep->wol_flag & FEC_WOL_FLAG_SLEEP_ON)) {
-		if (fep->quirks & FEC_QUIRK_HAS_MULTI_QUEUES) {
-			writel(0, fep->hwp + FEC_ECNTRL);
-		} else {
-			writel(FEC_ECR_RESET, fep->hwp + FEC_ECNTRL);
-			udelay(10);
-		}
-	} else {
-		val = readl(fep->hwp + FEC_ECNTRL);
-		val |= (FEC_ECR_MAGICEN | FEC_ECR_SLEEP);
-		writel(val, fep->hwp + FEC_ECNTRL);
-	}
+	fec_ctrl_reset(fep, true);
 	writel(fep->phy_speed, fep->hwp + FEC_MII_SPEED);
 	writel(FEC_DEFAULT_IMASK, fep->hwp + FEC_IMASK);
 
-- 
2.39.5

[PATCH AUTOSEL 6.14 622/642] i3c: master: svc: Fix implicit fallthrough in svc_i3c_master_ibi_work()

[Sasha Levin]

From: Nathan Chancellor <nathan@kernel.org>

[ Upstream commit e8d2d287e26d9bd9114cf258a123a6b70812442e ]

Clang warns (or errors with CONFIG_WERROR=y):

  drivers/i3c/master/svc-i3c-master.c:596:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
    596 |         default:
        |         ^
  drivers/i3c/master/svc-i3c-master.c:596:2: note: insert 'break;' to avoid fall-through
    596 |         default:
        |         ^
        |         break;
  1 error generated.

Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing break to silence
the warning.

Fixes: 0430bf9bc1ac ("i3c: master: svc: Fix missing STOP for master request")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20250319-i3c-fix-clang-fallthrough-v1-1-d8e02be1ef5c@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/i3c/master/svc-i3c-master.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/i3c/master/svc-i3c-master.c b/drivers/i3c/master/svc-i3c-master.c
index 2cf2c567f8931..75127b6c161f0 100644
--- a/drivers/i3c/master/svc-i3c-master.c
+++ b/drivers/i3c/master/svc-i3c-master.c
@@ -552,6 +552,7 @@ static void svc_i3c_master_ibi_work(struct work_struct *work)
 		break;
 	case SVC_I3C_MSTATUS_IBITYPE_MASTER_REQUEST:
 		svc_i3c_master_emit_stop(master);
+		break;
 	default:
 		break;
 	}
-- 
2.39.5