* [PATCH AUTOSEL 6.6 052/294] i3c: master: svc: Fix missing STOP for master request
[not found] <20250505225634.2688578-1-sashal@kernel.org>
@ 2025-05-05 22:52 ` Sasha Levin
2025-05-05 22:53 ` [PATCH AUTOSEL 6.6 130/294] clk: imx8mp: inform CCF of maximum frequency of clocks Sasha Levin
` (4 subsequent siblings)
5 siblings, 0 replies; 6+ messages in thread
From: Sasha Levin @ 2025-05-05 22:52 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Stanley Chu, Frank Li, Alexandre Belloni, Sasha Levin,
miquel.raynal, linux-i3c, imx
From: Stanley Chu <yschu@nuvoton.com>
[ Upstream commit 0430bf9bc1ac068c8b8c540eb93e5751872efc51 ]
The controller driver nacked the master request but didn't emit a
STOP to end the transaction. The driver shall refuse the unsupported
requests and return the controller state to IDLE by emitting a STOP.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250318053606.3087121-4-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/i3c/master/svc-i3c-master.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/i3c/master/svc-i3c-master.c b/drivers/i3c/master/svc-i3c-master.c
index fa1f12a89158c..3cef3794f10d3 100644
--- a/drivers/i3c/master/svc-i3c-master.c
+++ b/drivers/i3c/master/svc-i3c-master.c
@@ -503,6 +503,7 @@ static void svc_i3c_master_ibi_work(struct work_struct *work)
queue_work(master->base.wq, &master->hj_work);
break;
case SVC_I3C_MSTATUS_IBITYPE_MASTER_REQUEST:
+ svc_i3c_master_emit_stop(master);
default:
break;
}
--
2.39.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH AUTOSEL 6.6 130/294] clk: imx8mp: inform CCF of maximum frequency of clocks
[not found] <20250505225634.2688578-1-sashal@kernel.org>
2025-05-05 22:52 ` [PATCH AUTOSEL 6.6 052/294] i3c: master: svc: Fix missing STOP for master request Sasha Levin
@ 2025-05-05 22:53 ` Sasha Levin
2025-05-05 22:54 ` [PATCH AUTOSEL 6.6 184/294] i3c: master: svc: Flush FIFO before sending Dynamic Address Assignment(DAA) Sasha Levin
` (3 subsequent siblings)
5 siblings, 0 replies; 6+ messages in thread
From: Sasha Levin @ 2025-05-05 22:53 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Ahmad Fatoum, Peng Fan, Abel Vesa, Sasha Levin, abelvesa,
mturquette, sboyd, shawnguo, linux-clk, imx, linux-arm-kernel
From: Ahmad Fatoum <a.fatoum@pengutronix.de>
[ Upstream commit 06a61b5cb6a8638fa8823cd09b17233b29696fa2 ]
The IMX8MPCEC datasheet lists maximum frequencies allowed for different
modules. Some of these limits are universal, but some depend on
whether the SoC is operating in nominal or in overdrive mode.
The imx8mp.dtsi currently assumes overdrive mode and configures some
clocks in accordance with this. Boards wishing to make use of nominal
mode will need to override some of the clock rates manually.
As operating the clocks outside of their allowed range can lead to
difficult to debug issues, it makes sense to register the maximum rates
allowed in the driver, so the CCF can take them into account.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20250218-imx8m-clk-v4-6-b7697dc2dcd0@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/clk/imx/clk-imx8mp.c | 151 +++++++++++++++++++++++++++++++++++
1 file changed, 151 insertions(+)
diff --git a/drivers/clk/imx/clk-imx8mp.c b/drivers/clk/imx/clk-imx8mp.c
index 747f5397692e5..2a0804dd4b846 100644
--- a/drivers/clk/imx/clk-imx8mp.c
+++ b/drivers/clk/imx/clk-imx8mp.c
@@ -8,6 +8,7 @@
#include <linux/err.h>
#include <linux/io.h>
#include <linux/module.h>
+#include <linux/units.h>
#include <linux/of_address.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
@@ -406,11 +407,151 @@ static const char * const imx8mp_clkout_sels[] = {"audio_pll1_out", "audio_pll2_
static struct clk_hw **hws;
static struct clk_hw_onecell_data *clk_hw_data;
+struct imx8mp_clock_constraints {
+ unsigned int clkid;
+ u32 maxrate;
+};
+
+/*
+ * Below tables are taken from IMX8MPCEC Rev. 2.1, 07/2023
+ * Table 13. Maximum frequency of modules.
+ * Probable typos fixed are marked with a comment.
+ */
+static const struct imx8mp_clock_constraints imx8mp_clock_common_constraints[] = {
+ { IMX8MP_CLK_A53_DIV, 1000 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ENET_AXI, 266666667 }, /* Datasheet claims 266MHz */
+ { IMX8MP_CLK_NAND_USDHC_BUS, 266666667 }, /* Datasheet claims 266MHz */
+ { IMX8MP_CLK_MEDIA_APB, 200 * HZ_PER_MHZ },
+ { IMX8MP_CLK_HDMI_APB, 133333333 }, /* Datasheet claims 133MHz */
+ { IMX8MP_CLK_ML_AXI, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_AHB, 133333333 },
+ { IMX8MP_CLK_IPG_ROOT, 66666667 },
+ { IMX8MP_CLK_AUDIO_AHB, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_DISP2_PIX, 170 * HZ_PER_MHZ },
+ { IMX8MP_CLK_DRAM_ALT, 666666667 },
+ { IMX8MP_CLK_DRAM_APB, 200 * HZ_PER_MHZ },
+ { IMX8MP_CLK_CAN1, 80 * HZ_PER_MHZ },
+ { IMX8MP_CLK_CAN2, 80 * HZ_PER_MHZ },
+ { IMX8MP_CLK_PCIE_AUX, 10 * HZ_PER_MHZ },
+ { IMX8MP_CLK_I2C5, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_I2C6, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_SAI1, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_SAI2, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_SAI3, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_SAI5, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_SAI6, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_ENET_QOS, 125 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ENET_QOS_TIMER, 200 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ENET_REF, 125 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ENET_TIMER, 125 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ENET_PHY_REF, 125 * HZ_PER_MHZ },
+ { IMX8MP_CLK_NAND, 500 * HZ_PER_MHZ },
+ { IMX8MP_CLK_QSPI, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_USDHC1, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_USDHC2, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_I2C1, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_I2C2, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_I2C3, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_I2C4, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_UART1, 80 * HZ_PER_MHZ },
+ { IMX8MP_CLK_UART2, 80 * HZ_PER_MHZ },
+ { IMX8MP_CLK_UART3, 80 * HZ_PER_MHZ },
+ { IMX8MP_CLK_UART4, 80 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ECSPI1, 80 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ECSPI2, 80 * HZ_PER_MHZ },
+ { IMX8MP_CLK_PWM1, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_PWM2, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_PWM3, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_PWM4, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_GPT1, 100 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPT2, 100 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPT3, 100 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPT4, 100 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPT5, 100 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPT6, 100 * HZ_PER_MHZ },
+ { IMX8MP_CLK_WDOG, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_IPP_DO_CLKO1, 200 * HZ_PER_MHZ },
+ { IMX8MP_CLK_IPP_DO_CLKO2, 200 * HZ_PER_MHZ },
+ { IMX8MP_CLK_HDMI_REF_266M, 266 * HZ_PER_MHZ },
+ { IMX8MP_CLK_USDHC3, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_MIPI_PHY1_REF, 300 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_DISP1_PIX, 250 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_CAM2_PIX, 277 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_LDB, 595 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_MIPI_TEST_BYTE, 200 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ECSPI3, 80 * HZ_PER_MHZ },
+ { IMX8MP_CLK_PDM, 200 * HZ_PER_MHZ },
+ { IMX8MP_CLK_SAI7, 66666667 }, /* Datasheet claims 66MHz */
+ { IMX8MP_CLK_MAIN_AXI, 400 * HZ_PER_MHZ },
+ { /* Sentinel */ }
+};
+
+static const struct imx8mp_clock_constraints imx8mp_clock_nominal_constraints[] = {
+ { IMX8MP_CLK_M7_CORE, 600 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ML_CORE, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU3D_CORE, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU3D_SHADER_CORE, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU2D_CORE, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_AUDIO_AXI_SRC, 600 * HZ_PER_MHZ },
+ { IMX8MP_CLK_HSIO_AXI, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_ISP, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_VPU_BUS, 600 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_AXI, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_HDMI_AXI, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU_AXI, 600 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU_AHB, 300 * HZ_PER_MHZ },
+ { IMX8MP_CLK_NOC, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_NOC_IO, 600 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ML_AHB, 300 * HZ_PER_MHZ },
+ { IMX8MP_CLK_VPU_G1, 600 * HZ_PER_MHZ },
+ { IMX8MP_CLK_VPU_G2, 500 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_CAM1_PIX, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_VPU_VC8000E, 400 * HZ_PER_MHZ }, /* Datasheet claims 500MHz */
+ { IMX8MP_CLK_DRAM_CORE, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GIC, 400 * HZ_PER_MHZ },
+ { /* Sentinel */ }
+};
+
+static const struct imx8mp_clock_constraints imx8mp_clock_overdrive_constraints[] = {
+ { IMX8MP_CLK_M7_CORE, 800 * HZ_PER_MHZ},
+ { IMX8MP_CLK_ML_CORE, 1000 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU3D_CORE, 1000 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU3D_SHADER_CORE, 1000 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU2D_CORE, 1000 * HZ_PER_MHZ },
+ { IMX8MP_CLK_AUDIO_AXI_SRC, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_HSIO_AXI, 500 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_ISP, 500 * HZ_PER_MHZ },
+ { IMX8MP_CLK_VPU_BUS, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_AXI, 500 * HZ_PER_MHZ },
+ { IMX8MP_CLK_HDMI_AXI, 500 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU_AXI, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GPU_AHB, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_NOC, 1000 * HZ_PER_MHZ },
+ { IMX8MP_CLK_NOC_IO, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_ML_AHB, 400 * HZ_PER_MHZ },
+ { IMX8MP_CLK_VPU_G1, 800 * HZ_PER_MHZ },
+ { IMX8MP_CLK_VPU_G2, 700 * HZ_PER_MHZ },
+ { IMX8MP_CLK_MEDIA_CAM1_PIX, 500 * HZ_PER_MHZ },
+ { IMX8MP_CLK_VPU_VC8000E, 500 * HZ_PER_MHZ }, /* Datasheet claims 400MHz */
+ { IMX8MP_CLK_DRAM_CORE, 1000 * HZ_PER_MHZ },
+ { IMX8MP_CLK_GIC, 500 * HZ_PER_MHZ },
+ { /* Sentinel */ }
+};
+
+static void imx8mp_clocks_apply_constraints(const struct imx8mp_clock_constraints constraints[])
+{
+ const struct imx8mp_clock_constraints *constr;
+
+ for (constr = constraints; constr->clkid; constr++)
+ clk_hw_set_rate_range(hws[constr->clkid], 0, constr->maxrate);
+}
+
static int imx8mp_clocks_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct device_node *np;
void __iomem *anatop_base, *ccm_base;
+ const char *opmode;
int err;
np = of_find_compatible_node(NULL, NULL, "fsl,imx8mp-anatop");
@@ -715,6 +856,16 @@ static int imx8mp_clocks_probe(struct platform_device *pdev)
imx_check_clk_hws(hws, IMX8MP_CLK_END);
+ imx8mp_clocks_apply_constraints(imx8mp_clock_common_constraints);
+
+ err = of_property_read_string(np, "fsl,operating-mode", &opmode);
+ if (!err) {
+ if (!strcmp(opmode, "nominal"))
+ imx8mp_clocks_apply_constraints(imx8mp_clock_nominal_constraints);
+ else if (!strcmp(opmode, "overdrive"))
+ imx8mp_clocks_apply_constraints(imx8mp_clock_overdrive_constraints);
+ }
+
err = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, clk_hw_data);
if (err < 0) {
dev_err(dev, "failed to register hws for i.MX8MP\n");
--
2.39.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH AUTOSEL 6.6 184/294] i3c: master: svc: Flush FIFO before sending Dynamic Address Assignment(DAA)
[not found] <20250505225634.2688578-1-sashal@kernel.org>
2025-05-05 22:52 ` [PATCH AUTOSEL 6.6 052/294] i3c: master: svc: Fix missing STOP for master request Sasha Levin
2025-05-05 22:53 ` [PATCH AUTOSEL 6.6 130/294] clk: imx8mp: inform CCF of maximum frequency of clocks Sasha Levin
@ 2025-05-05 22:54 ` Sasha Levin
2025-05-05 22:54 ` [PATCH AUTOSEL 6.6 186/294] serial: mctrl_gpio: split disable_ms into sync and no_sync APIs Sasha Levin
` (2 subsequent siblings)
5 siblings, 0 replies; 6+ messages in thread
From: Sasha Levin @ 2025-05-05 22:54 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Frank Li, Miquel Raynal, Alexandre Belloni, Sasha Levin,
linux-i3c, imx
From: Frank Li <Frank.Li@nxp.com>
[ Upstream commit a892ee4cf22a50e1d6988d0464a9a421f3e5db2f ]
Ensure the FIFO is empty before issuing the DAA command to prevent
incorrect command data from being sent. Align with other data transfers,
such as svc_i3c_master_start_xfer_locked(), which flushes the FIFO before
sending a command.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250129162250.3629189-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/i3c/master/svc-i3c-master.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/i3c/master/svc-i3c-master.c b/drivers/i3c/master/svc-i3c-master.c
index 3cef3794f10d3..3d1734849e0d9 100644
--- a/drivers/i3c/master/svc-i3c-master.c
+++ b/drivers/i3c/master/svc-i3c-master.c
@@ -841,6 +841,8 @@ static int svc_i3c_master_do_daa_locked(struct svc_i3c_master *master,
u32 reg;
int ret, i;
+ svc_i3c_master_flush_fifo(master);
+
while (true) {
/* Enter/proceed with DAA */
writel(SVC_I3C_MCTRL_REQUEST_PROC_DAA |
--
2.39.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH AUTOSEL 6.6 186/294] serial: mctrl_gpio: split disable_ms into sync and no_sync APIs
[not found] <20250505225634.2688578-1-sashal@kernel.org>
` (2 preceding siblings ...)
2025-05-05 22:54 ` [PATCH AUTOSEL 6.6 184/294] i3c: master: svc: Flush FIFO before sending Dynamic Address Assignment(DAA) Sasha Levin
@ 2025-05-05 22:54 ` Sasha Levin
2025-05-05 22:54 ` [PATCH AUTOSEL 6.6 188/294] pmdomain: imx: gpcv2: use proper helper for property detection Sasha Levin
2025-05-05 22:55 ` [PATCH AUTOSEL 6.6 239/294] net: fec: Refactor MAC reset to function Sasha Levin
5 siblings, 0 replies; 6+ messages in thread
From: Sasha Levin @ 2025-05-05 22:54 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Alexis Lothoré, Jiri Slaby, Richard Genoud,
Greg Kroah-Hartman, Sasha Levin, corbet, nicolas.ferre,
alexandre.belloni, claudiu.beznea, shawnguo, mcoquelin.stm32,
alexandre.torgue, john.ogness, pmladek, arnd, namcao,
benjamin.larsson, schnelle, esben, zack.rusin, festevam, marex,
stefan.eichenberger, linux, tglx, jeff.johnson, linux,
geert+renesas, wsa+renesas, prabhakar.mahadev-lad.rj,
ben.wolsieffer, cheick.traore, u.kleine-koenig, linux-serial,
linux-doc, linux-arm-kernel, imx, linux-stm32
From: Alexis Lothoré <alexis.lothore@bootlin.com>
[ Upstream commit 1bd2aad57da95f7f2d2bb52f7ad15c0f4993a685 ]
The following splat has been observed on a SAMA5D27 platform using
atmel_serial:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:738
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 27, name: kworker/u5:0
preempt_count: 1, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
CPU: 0 UID: 0 PID: 27 Comm: kworker/u5:0 Not tainted 6.13.0-rc7+ #74
Hardware name: Atmel SAMA5
Workqueue: hci0 hci_power_on [bluetooth]
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __might_resched+0x38c/0x598
__might_resched from disable_irq+0x1c/0x48
disable_irq from mctrl_gpio_disable_ms+0x74/0xc0
mctrl_gpio_disable_ms from atmel_disable_ms.part.0+0x80/0x1f4
atmel_disable_ms.part.0 from atmel_set_termios+0x764/0x11e8
atmel_set_termios from uart_change_line_settings+0x15c/0x994
uart_change_line_settings from uart_set_termios+0x2b0/0x668
uart_set_termios from tty_set_termios+0x600/0x8ec
tty_set_termios from ttyport_set_flow_control+0x188/0x1e0
ttyport_set_flow_control from wilc_setup+0xd0/0x524 [hci_wilc]
wilc_setup [hci_wilc] from hci_dev_open_sync+0x330/0x203c [bluetooth]
hci_dev_open_sync [bluetooth] from hci_dev_do_open+0x40/0xb0 [bluetooth]
hci_dev_do_open [bluetooth] from hci_power_on+0x12c/0x664 [bluetooth]
hci_power_on [bluetooth] from process_one_work+0x998/0x1a38
process_one_work from worker_thread+0x6e0/0xfb4
worker_thread from kthread+0x3d4/0x484
kthread from ret_from_fork+0x14/0x28
This warning is emitted when trying to toggle, at the highest level,
some flow control (with serdev_device_set_flow_control) in a device
driver. At the lowest level, the atmel_serial driver is using
serial_mctrl_gpio lib to enable/disable the corresponding IRQs
accordingly. The warning emitted by CONFIG_DEBUG_ATOMIC_SLEEP is due to
disable_irq (called in mctrl_gpio_disable_ms) being possibly called in
some atomic context (some tty drivers perform modem lines configuration
in regions protected by port lock).
Split mctrl_gpio_disable_ms into two differents APIs, a non-blocking one
and a blocking one. Replace mctrl_gpio_disable_ms calls with the
relevant version depending on whether the call is protected by some port
lock.
Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Acked-by: Richard Genoud <richard.genoud@bootlin.com>
Link: https://lore.kernel.org/r/20250217-atomic_sleep_mctrl_serial_gpio-v3-1-59324b313eef@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
Documentation/driver-api/serial/driver.rst | 2 +-
drivers/tty/serial/8250/8250_port.c | 2 +-
drivers/tty/serial/atmel_serial.c | 2 +-
drivers/tty/serial/imx.c | 2 +-
drivers/tty/serial/serial_mctrl_gpio.c | 34 +++++++++++++++++-----
drivers/tty/serial/serial_mctrl_gpio.h | 17 +++++++++--
drivers/tty/serial/sh-sci.c | 2 +-
drivers/tty/serial/stm32-usart.c | 2 +-
8 files changed, 47 insertions(+), 16 deletions(-)
diff --git a/Documentation/driver-api/serial/driver.rst b/Documentation/driver-api/serial/driver.rst
index 84b43061c11be..60434f2b02863 100644
--- a/Documentation/driver-api/serial/driver.rst
+++ b/Documentation/driver-api/serial/driver.rst
@@ -103,4 +103,4 @@ Some helpers are provided in order to set/get modem control lines via GPIO.
.. kernel-doc:: drivers/tty/serial/serial_mctrl_gpio.c
:identifiers: mctrl_gpio_init mctrl_gpio_free mctrl_gpio_to_gpiod
mctrl_gpio_set mctrl_gpio_get mctrl_gpio_enable_ms
- mctrl_gpio_disable_ms
+ mctrl_gpio_disable_ms_sync mctrl_gpio_disable_ms_no_sync
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index c2778300e1510..d5ad6cae6b652 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -1676,7 +1676,7 @@ static void serial8250_disable_ms(struct uart_port *port)
if (up->bugs & UART_BUG_NOMSR)
return;
- mctrl_gpio_disable_ms(up->gpios);
+ mctrl_gpio_disable_ms_no_sync(up->gpios);
up->ier &= ~UART_IER_MSI;
serial_port_out(port, UART_IER, up->ier);
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index bcca5627afaca..85559d9b35d83 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -698,7 +698,7 @@ static void atmel_disable_ms(struct uart_port *port)
atmel_port->ms_irq_enabled = false;
- mctrl_gpio_disable_ms(atmel_port->gpios);
+ mctrl_gpio_disable_ms_no_sync(atmel_port->gpios);
if (!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
idr |= ATMEL_US_CTSIC;
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index 349d4849ba5e3..04809b781f45b 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -1597,7 +1597,7 @@ static void imx_uart_shutdown(struct uart_port *port)
imx_uart_dma_exit(sport);
}
- mctrl_gpio_disable_ms(sport->gpios);
+ mctrl_gpio_disable_ms_sync(sport->gpios);
spin_lock_irqsave(&sport->port.lock, flags);
ucr2 = imx_uart_readl(sport, UCR2);
diff --git a/drivers/tty/serial/serial_mctrl_gpio.c b/drivers/tty/serial/serial_mctrl_gpio.c
index 7d5aaa8d422b1..d5fb293dd5a93 100644
--- a/drivers/tty/serial/serial_mctrl_gpio.c
+++ b/drivers/tty/serial/serial_mctrl_gpio.c
@@ -322,11 +322,7 @@ void mctrl_gpio_enable_ms(struct mctrl_gpios *gpios)
}
EXPORT_SYMBOL_GPL(mctrl_gpio_enable_ms);
-/**
- * mctrl_gpio_disable_ms - disable irqs and handling of changes to the ms lines
- * @gpios: gpios to disable
- */
-void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios)
+static void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios, bool sync)
{
enum mctrl_gpio_idx i;
@@ -342,10 +338,34 @@ void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios)
if (!gpios->irq[i])
continue;
- disable_irq(gpios->irq[i]);
+ if (sync)
+ disable_irq(gpios->irq[i]);
+ else
+ disable_irq_nosync(gpios->irq[i]);
}
}
-EXPORT_SYMBOL_GPL(mctrl_gpio_disable_ms);
+
+/**
+ * mctrl_gpio_disable_ms_sync - disable irqs and handling of changes to the ms
+ * lines, and wait for any pending IRQ to be processed
+ * @gpios: gpios to disable
+ */
+void mctrl_gpio_disable_ms_sync(struct mctrl_gpios *gpios)
+{
+ mctrl_gpio_disable_ms(gpios, true);
+}
+EXPORT_SYMBOL_GPL(mctrl_gpio_disable_ms_sync);
+
+/**
+ * mctrl_gpio_disable_ms_no_sync - disable irqs and handling of changes to the
+ * ms lines, and return immediately
+ * @gpios: gpios to disable
+ */
+void mctrl_gpio_disable_ms_no_sync(struct mctrl_gpios *gpios)
+{
+ mctrl_gpio_disable_ms(gpios, false);
+}
+EXPORT_SYMBOL_GPL(mctrl_gpio_disable_ms_no_sync);
void mctrl_gpio_enable_irq_wake(struct mctrl_gpios *gpios)
{
diff --git a/drivers/tty/serial/serial_mctrl_gpio.h b/drivers/tty/serial/serial_mctrl_gpio.h
index fc76910fb105a..79e97838ebe56 100644
--- a/drivers/tty/serial/serial_mctrl_gpio.h
+++ b/drivers/tty/serial/serial_mctrl_gpio.h
@@ -87,9 +87,16 @@ void mctrl_gpio_free(struct device *dev, struct mctrl_gpios *gpios);
void mctrl_gpio_enable_ms(struct mctrl_gpios *gpios);
/*
- * Disable gpio interrupts to report status line changes.
+ * Disable gpio interrupts to report status line changes, and block until
+ * any corresponding IRQ is processed
*/
-void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios);
+void mctrl_gpio_disable_ms_sync(struct mctrl_gpios *gpios);
+
+/*
+ * Disable gpio interrupts to report status line changes, and return
+ * immediately
+ */
+void mctrl_gpio_disable_ms_no_sync(struct mctrl_gpios *gpios);
/*
* Enable gpio wakeup interrupts to enable wake up source.
@@ -148,7 +155,11 @@ static inline void mctrl_gpio_enable_ms(struct mctrl_gpios *gpios)
{
}
-static inline void mctrl_gpio_disable_ms(struct mctrl_gpios *gpios)
+static inline void mctrl_gpio_disable_ms_sync(struct mctrl_gpios *gpios)
+{
+}
+
+static inline void mctrl_gpio_disable_ms_no_sync(struct mctrl_gpios *gpios)
{
}
diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index 4350a69d97d7a..2434eb6e6847d 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -2237,7 +2237,7 @@ static void sci_shutdown(struct uart_port *port)
dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
s->autorts = false;
- mctrl_gpio_disable_ms(to_sci_port(port)->gpios);
+ mctrl_gpio_disable_ms_sync(to_sci_port(port)->gpios);
spin_lock_irqsave(&port->lock, flags);
sci_stop_rx(port);
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 9ef90bb30a47e..b58422ae156c9 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -952,7 +952,7 @@ static void stm32_usart_enable_ms(struct uart_port *port)
static void stm32_usart_disable_ms(struct uart_port *port)
{
- mctrl_gpio_disable_ms(to_stm32_port(port)->gpios);
+ mctrl_gpio_disable_ms_sync(to_stm32_port(port)->gpios);
}
/* Transmit stop */
--
2.39.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH AUTOSEL 6.6 188/294] pmdomain: imx: gpcv2: use proper helper for property detection
[not found] <20250505225634.2688578-1-sashal@kernel.org>
` (3 preceding siblings ...)
2025-05-05 22:54 ` [PATCH AUTOSEL 6.6 186/294] serial: mctrl_gpio: split disable_ms into sync and no_sync APIs Sasha Levin
@ 2025-05-05 22:54 ` Sasha Levin
2025-05-05 22:55 ` [PATCH AUTOSEL 6.6 239/294] net: fec: Refactor MAC reset to function Sasha Levin
5 siblings, 0 replies; 6+ messages in thread
From: Sasha Levin @ 2025-05-05 22:54 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Ahmad Fatoum, Ulf Hansson, Sasha Levin, shawnguo, shengjiu.wang,
dario.binacchi, peng.fan, michael, krzysztof.kozlowski, joe,
linux-pm, imx, linux-arm-kernel
From: Ahmad Fatoum <a.fatoum@pengutronix.de>
[ Upstream commit 6568cb40e73163fa25e2779f7234b169b2e1a32e ]
Starting with commit c141ecc3cecd7 ("of: Warn when of_property_read_bool()
is used on non-boolean properties"), probing the gpcv2 device on i.MX8M
SoCs leads to warnings when LOCKDEP is enabled.
Fix this by checking property presence with of_property_present as
intended.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20250218-gpcv2-of-property-present-v1-1-3bb1a9789654@pengutronix.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/pmdomain/imx/gpcv2.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/pmdomain/imx/gpcv2.c b/drivers/pmdomain/imx/gpcv2.c
index 13fce2b134f60..84d68c805cac8 100644
--- a/drivers/pmdomain/imx/gpcv2.c
+++ b/drivers/pmdomain/imx/gpcv2.c
@@ -1350,7 +1350,7 @@ static int imx_pgc_domain_probe(struct platform_device *pdev)
}
if (IS_ENABLED(CONFIG_LOCKDEP) &&
- of_property_read_bool(domain->dev->of_node, "power-domains"))
+ of_property_present(domain->dev->of_node, "power-domains"))
lockdep_set_subclass(&domain->genpd.mlock, 1);
ret = of_genpd_add_provider_simple(domain->dev->of_node,
--
2.39.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH AUTOSEL 6.6 239/294] net: fec: Refactor MAC reset to function
[not found] <20250505225634.2688578-1-sashal@kernel.org>
` (4 preceding siblings ...)
2025-05-05 22:54 ` [PATCH AUTOSEL 6.6 188/294] pmdomain: imx: gpcv2: use proper helper for property detection Sasha Levin
@ 2025-05-05 22:55 ` Sasha Levin
5 siblings, 0 replies; 6+ messages in thread
From: Sasha Levin @ 2025-05-05 22:55 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Csókás, Bence, Michal Swiatkowski, Jacob Keller,
Simon Horman, Paolo Abeni, Sasha Levin, wei.fang, andrew+netdev,
davem, edumazet, kuba, imx, netdev
From: Csókás, Bence <csokas.bence@prolan.hu>
[ Upstream commit 67800d296191d0a9bde0a7776f99ca1ddfa0fc26 ]
The core is reset both in `fec_restart()` (called on link-up) and
`fec_stop()` (going to sleep, driver remove etc.). These two functions
had their separate implementations, which was at first only a register
write and a `udelay()` (and the accompanying block comment). However,
since then we got soft-reset (MAC disable) and Wake-on-LAN support, which
meant that these implementations diverged, often causing bugs.
For instance, as of now, `fec_stop()` does not check for
`FEC_QUIRK_NO_HARD_RESET`, meaning the MII/RMII mode is cleared on eg.
a PM power-down event; and `fec_restart()` missed the refactor renaming
the "magic" constant `1` to `FEC_ECR_RESET`.
To harmonize current implementations, and eliminate this source of
potential future bugs, refactor implementation to a common function.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Csókás, Bence <csokas.bence@prolan.hu>
Link: https://patch.msgid.link/20250207121255.161146-2-csokas.bence@prolan.hu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/net/ethernet/freescale/fec_main.c | 52 +++++++++++------------
1 file changed, 25 insertions(+), 27 deletions(-)
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
index 2d6b50903c923..419df6559492e 100644
--- a/drivers/net/ethernet/freescale/fec_main.c
+++ b/drivers/net/ethernet/freescale/fec_main.c
@@ -1074,6 +1074,29 @@ static void fec_enet_enable_ring(struct net_device *ndev)
}
}
+/* Whack a reset. We should wait for this.
+ * For i.MX6SX SOC, enet use AXI bus, we use disable MAC
+ * instead of reset MAC itself.
+ */
+static void fec_ctrl_reset(struct fec_enet_private *fep, bool allow_wol)
+{
+ u32 val;
+
+ if (!allow_wol || !(fep->wol_flag & FEC_WOL_FLAG_SLEEP_ON)) {
+ if (fep->quirks & FEC_QUIRK_HAS_MULTI_QUEUES ||
+ ((fep->quirks & FEC_QUIRK_NO_HARD_RESET) && fep->link)) {
+ writel(0, fep->hwp + FEC_ECNTRL);
+ } else {
+ writel(FEC_ECR_RESET, fep->hwp + FEC_ECNTRL);
+ udelay(10);
+ }
+ } else {
+ val = readl(fep->hwp + FEC_ECNTRL);
+ val |= (FEC_ECR_MAGICEN | FEC_ECR_SLEEP);
+ writel(val, fep->hwp + FEC_ECNTRL);
+ }
+}
+
/*
* This function is called to start or restart the FEC during a link
* change, transmit timeout, or to reconfigure the FEC. The network
@@ -1090,17 +1113,7 @@ fec_restart(struct net_device *ndev)
if (fep->bufdesc_ex)
fec_ptp_save_state(fep);
- /* Whack a reset. We should wait for this.
- * For i.MX6SX SOC, enet use AXI bus, we use disable MAC
- * instead of reset MAC itself.
- */
- if (fep->quirks & FEC_QUIRK_HAS_MULTI_QUEUES ||
- ((fep->quirks & FEC_QUIRK_NO_HARD_RESET) && fep->link)) {
- writel(0, fep->hwp + FEC_ECNTRL);
- } else {
- writel(1, fep->hwp + FEC_ECNTRL);
- udelay(10);
- }
+ fec_ctrl_reset(fep, false);
/*
* enet-mac reset will reset mac address registers too,
@@ -1354,22 +1367,7 @@ fec_stop(struct net_device *ndev)
if (fep->bufdesc_ex)
fec_ptp_save_state(fep);
- /* Whack a reset. We should wait for this.
- * For i.MX6SX SOC, enet use AXI bus, we use disable MAC
- * instead of reset MAC itself.
- */
- if (!(fep->wol_flag & FEC_WOL_FLAG_SLEEP_ON)) {
- if (fep->quirks & FEC_QUIRK_HAS_MULTI_QUEUES) {
- writel(0, fep->hwp + FEC_ECNTRL);
- } else {
- writel(FEC_ECR_RESET, fep->hwp + FEC_ECNTRL);
- udelay(10);
- }
- } else {
- val = readl(fep->hwp + FEC_ECNTRL);
- val |= (FEC_ECR_MAGICEN | FEC_ECR_SLEEP);
- writel(val, fep->hwp + FEC_ECNTRL);
- }
+ fec_ctrl_reset(fep, true);
writel(fep->phy_speed, fep->hwp + FEC_MII_SPEED);
writel(FEC_DEFAULT_IMASK, fep->hwp + FEC_IMASK);
--
2.39.5
^ permalink raw reply related [flat|nested] 6+ messages in thread
end of thread, other threads:[~2025-05-05 23:04 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <20250505225634.2688578-1-sashal@kernel.org>
2025-05-05 22:52 ` [PATCH AUTOSEL 6.6 052/294] i3c: master: svc: Fix missing STOP for master request Sasha Levin
2025-05-05 22:53 ` [PATCH AUTOSEL 6.6 130/294] clk: imx8mp: inform CCF of maximum frequency of clocks Sasha Levin
2025-05-05 22:54 ` [PATCH AUTOSEL 6.6 184/294] i3c: master: svc: Flush FIFO before sending Dynamic Address Assignment(DAA) Sasha Levin
2025-05-05 22:54 ` [PATCH AUTOSEL 6.6 186/294] serial: mctrl_gpio: split disable_ms into sync and no_sync APIs Sasha Levin
2025-05-05 22:54 ` [PATCH AUTOSEL 6.6 188/294] pmdomain: imx: gpcv2: use proper helper for property detection Sasha Levin
2025-05-05 22:55 ` [PATCH AUTOSEL 6.6 239/294] net: fec: Refactor MAC reset to function Sasha Levin
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox