[PATCH V6 00/12] pci-imx6: Add support for parsing the reset property in new Root Port binding

[PATCH V6 00/12] pci-imx6: Add support for parsing the reset property in new Root Port binding

[Sherry Sun]

This patch set adds support for parsing the reset property in new Root Port
binding in pci-imx6 driver, similar to the implementation in the qcom pcie
driver[1].

Also introduce generic helper functions to parse Root Port device tree
nodes and extract common properties like reset GPIOs. This allows multiple
PCI host controller drivers to share the same parsing logic.

Define struct pci_host_port to hold common Root Port properties
(currently only reset GPIO descriptor) and add
pci_host_common_parse_ports() to parse Root Port nodes from device tree.
Also add the 'ports' list to struct pci_host_bridge for better maintain
parsed Root Port information.

The plan is to add the wake-gpio property to the root port in subsequent
patches. Also, the vpcie-supply property will be moved to the root port
node later based on the refactoring patch set for the PCI pwrctrl
framework[2]. 

The initial idea is to adopt the Manivannan’s recent PCIe M.2 KeyE
connector support patch set[3] and PCI power control framework patches[2],
and extend them to the pcie-imx6 driver. Since the new M.2/pwrctrl model is
implemented based on Root Ports and requires the pwrctrl driver to bind to
a Root Port device, we need to introduce a Root Port child node on i.MX
boards that provide an M.2 connector.

To follow a more standardized DT structure, it also makes sense to move
the reset-gpios and wake-gpios properties into the Root Port node. These
signals logically belong to the Root Port rather than the host bridge,
and placing them there aligns with the new M.2/pwrctrl model.

Regarding backward compatibility, as Frank suggested, I will not remove
the old reset-gpio property from existing DTS files to avoid function
break.

For new i.MX platforms — such as the upcoming i.MX952-evk will add
vpcie-supply, reset-gpios, and wake-gpios directly under the Root Port
node.
Therefore, driver updates are needed to support both the legacy
properties and the new standardized Root Port based layout.

[1] https://lore.kernel.org/linux-pci/20250702-perst-v5-0-920b3d1f6ee1@qti.qualcomm.com/
[2] https://lore.kernel.org/linux-pci/20260115-pci-pwrctrl-rework-v5-0-9d26da3ce903@oss.qualcomm.com/
[3] https://lore.kernel.org/linux-pci/20260112-pci-m2-e-v4-0-eff84d2c6d26@oss.qualcomm.com/

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
Changes in V6:
1. Drop the pre-allocate pci_host_bridge struct changes in dw_pcie_host_init()
   and imx_pcie_probe().
2. Parse Root Port nodes in dw_pcie_host_init() as Frank and Mani suggested.
3. Move the imx_pcie_parse_legacy_binding() from imx_pcie_probe() to
   imx_pcie_host_init(), so that dw_pcie_host_init() parse Root Port first, if
   no Root Port nodes were parsed(indicated by empty ports list), then parse
   legacy binding.
4. Add device pointer parameter for pci_host_common_parse_ports().
5. Add NULL pointer check for reset gpio in imx_pcie_parse_legacy_binding().

Changes in V5:
1. Add the Root Port list(pci_host_port) to struct pci_host_bridge for better
   maintain parsed Root Port information.
2. Delete the pci_host_common_delete_ports() as now the Root Port list in
   pci_host_bridge can be cleared by pci_release_host_bridge_dev().
3. Change the common API pci_host_common_parse_ports() pass down struct
   pci_host_bridge *. 
4. Modify dw_pcie_host_init() to allow drivers to pre-allocate pci_host_bridge
   struct when needed.
5. Allocate bridge early in imx_pcie_probe() to parse Root Ports.

Changes in V4:
1. Add common helpers for parsing Root Port properties in pci-host-common.c in
   patch#2.
2. Call common pci_host_common_parse_ports() and pci_host_common_delete_ports()
   in pci-imx6 driver.
3. Use PCIE_T_PVPERL_MS and PCIE_RESET_CONFIG_WAIT_MS instead of magic number
   100 in patch#3 as Manivannan suggested.
4. Use "PERST#" instead of "PCIe reset" for the reset gpio lable in patch#3.

Changes in V3:
1. Improve the patch#2 commit message as Frank suggested.
2. Add Reviewed-by tag for patch#1.

Changes in V2:
1. Improve the patch#1 commit message as Frank suggested.
2. Also mark the reset-gpio-active-high property as deprecated in
   imx6q-pcie DT binding as Rob suggested.
3. The imx_pcie_delete_ports() has been moved up so that the
   imx_pcie_parse_ports() can call this helper function in error handling.
4. Keep the old reset-gpio property in the host bridge node for the
   existing dts files and add comments to avoid confusion.
---

Sherry Sun (12):
  dt-bindings: PCI: fsl,imx6q-pcie: Add reset GPIO in Root Port node
  PCI: host-generic: Add common helpers for parsing Root Port properties
  PCI: dwc: Parse Root Port nodes in dw_pcie_host_init()
  PCI: imx6: Add support for parsing the reset property in new Root Port
    binding
  arm: dts: imx6qdl: Add Root Port node and PERST property
  arm: dts: imx6sx: Add Root Port node and PERST property
  arm: dts: imx7d: Add Root Port node and PERST property
  arm64: dts: imx8mm: Add Root Port node and PERST property
  arm64: dts: imx8mp: Add Root Port node and PERST property
  arm64: dts: imx8mq: Add Root Port node and PERST property
  arm64: dts: imx8dxl/qm/qxp: Add Root Port node and PERST property
  arm64: dts: imx95: Add Root Port node and PERST property

 .../bindings/pci/fsl,imx6q-pcie.yaml          | 32 ++++++++
 .../arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi |  5 ++
 arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi        | 11 +++
 .../arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts |  5 ++
 arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi     |  5 ++
 arch/arm/boot/dts/nxp/imx/imx6sx.dtsi         | 11 +++
 arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts       |  5 ++
 arch/arm/boot/dts/nxp/imx/imx7d.dtsi          | 11 +++
 .../boot/dts/freescale/imx8-ss-hsio.dtsi      | 11 +++
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts |  5 ++
 arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi |  5 ++
 arch/arm64/boot/dts/freescale/imx8mm.dtsi     | 11 +++
 arch/arm64/boot/dts/freescale/imx8mp-evk.dts  |  5 ++
 arch/arm64/boot/dts/freescale/imx8mp.dtsi     | 11 +++
 arch/arm64/boot/dts/freescale/imx8mq-evk.dts  | 10 +++
 arch/arm64/boot/dts/freescale/imx8mq.dtsi     | 22 ++++++
 arch/arm64/boot/dts/freescale/imx8qm-mek.dts  | 10 +++
 .../boot/dts/freescale/imx8qm-ss-hsio.dtsi    | 22 ++++++
 arch/arm64/boot/dts/freescale/imx8qxp-mek.dts |  5 ++
 .../boot/dts/freescale/imx95-15x15-evk.dts    |  5 ++
 .../boot/dts/freescale/imx95-19x19-evk.dts    | 10 +++
 arch/arm64/boot/dts/freescale/imx95.dtsi      | 22 ++++++
 drivers/pci/controller/dwc/pci-imx6.c         | 76 +++++++++++++++----
 .../pci/controller/dwc/pcie-designware-host.c |  8 ++
 drivers/pci/controller/pci-host-common.c      | 58 ++++++++++++++
 drivers/pci/controller/pci-host-common.h      | 15 ++++
 drivers/pci/probe.c                           |  2 +
 include/linux/pci.h                           |  1 +
 28 files changed, 384 insertions(+), 15 deletions(-)

-- 
2.37.1

[PATCH V6 01/12] dt-bindings: PCI: fsl,imx6q-pcie: Add reset GPIO in Root Port node

[Sherry Sun]

Update fsl,imx6q-pcie.yaml to include the standard reset-gpios property
for the Root Port node.

The reset-gpios property is already defined in pci-bus-common.yaml for
PERST#, so use it instead of the local reset-gpio property. Keep the
existing reset-gpio property in the bridge node for backward
compatibility, but mark it as deprecated.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
---
 .../bindings/pci/fsl,imx6q-pcie.yaml          | 32 +++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
index 12a01f7a5744..d1a2526f43dc 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
@@ -59,16 +59,34 @@ properties:
       - const: dma
 
   reset-gpio:
+    deprecated: true
     description: Should specify the GPIO for controlling the PCI bus device
       reset signal. It's not polarity aware and defaults to active-low reset
       sequence (L=reset state, H=operation state) (optional required).
+      This property is deprecated, instead of referencing this property from the
+      host bridge node, use the reset-gpios property from the root port node.
 
   reset-gpio-active-high:
+    deprecated: true
     description: If present then the reset sequence using the GPIO
       specified in the "reset-gpio" property is reversed (H=reset state,
       L=operation state) (optional required).
+      This property is deprecated along with the reset-gpio property above, use
+      the reset-gpios property from the root port node.
     type: boolean
 
+  pcie@0:
+    description:
+      Describe the i.MX6 PCIe Root Port.
+    type: object
+    $ref: /schemas/pci/pci-pci-bridge.yaml#
+
+    properties:
+      reg:
+        maxItems: 1
+
+    unevaluatedProperties: false
+
 required:
   - compatible
   - reg
@@ -229,6 +247,7 @@ unevaluatedProperties: false
 examples:
   - |
     #include <dt-bindings/clock/imx6qdl-clock.h>
+    #include <dt-bindings/gpio/gpio.h>
     #include <dt-bindings/interrupt-controller/arm-gic.h>
 
     pcie: pcie@1ffc000 {
@@ -255,5 +274,18 @@ examples:
                 <&clks IMX6QDL_CLK_LVDS1_GATE>,
                 <&clks IMX6QDL_CLK_PCIE_REF_125M>;
         clock-names = "pcie", "pcie_bus", "pcie_phy";
+
+        pcie_port0: pcie@0 {
+            compatible = "pciclass,0604";
+            device_type = "pci";
+            reg = <0x0 0x0 0x0 0x0 0x0>;
+            bus-range = <0x01 0xff>;
+
+            #address-cells = <3>;
+            #size-cells = <2>;
+            ranges;
+
+            reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+        };
     };
 ...
-- 
2.37.1

[PATCH V6 02/12] PCI: host-generic: Add common helpers for parsing Root Port properties

[Sherry Sun]

Introduce generic helper functions to parse Root Port device tree nodes
and extract common properties like reset GPIOs. This allows multiple
PCI host controller drivers to share the same parsing logic.

Define struct pci_host_port to hold common Root Port properties
(currently only reset GPIO descriptor) and add
pci_host_common_parse_ports() to parse Root Port nodes from device tree.

Also add the 'ports' list to struct pci_host_bridge for better maintain
parsed Root Port information.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 drivers/pci/controller/pci-host-common.c | 58 ++++++++++++++++++++++++
 drivers/pci/controller/pci-host-common.h | 15 ++++++
 drivers/pci/probe.c                      |  2 +
 include/linux/pci.h                      |  1 +
 4 files changed, 76 insertions(+)

diff --git a/drivers/pci/controller/pci-host-common.c b/drivers/pci/controller/pci-host-common.c
index d6258c1cffe5..b9a958f745d9 100644
--- a/drivers/pci/controller/pci-host-common.c
+++ b/drivers/pci/controller/pci-host-common.c
@@ -9,6 +9,7 @@
 
 #include <linux/kernel.h>
 #include <linux/module.h>
+#include <linux/gpio/consumer.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_pci.h>
@@ -17,6 +18,63 @@
 
 #include "pci-host-common.h"
 
+/**
+ * pci_host_common_parse_port - Parse a single Root Port node
+ * @bridge: PCI host bridge
+ * @node: Device tree node of the Root Port
+ *
+ * Returns: 0 on success, negative error code on failure
+ */
+static int pci_host_common_parse_port(struct pci_host_bridge *bridge,
+				      struct device_node *node)
+{
+	struct device *dev = &bridge->dev;
+	struct pci_host_port *port;
+	struct gpio_desc *reset;
+
+	reset = devm_fwnode_gpiod_get(dev, of_fwnode_handle(node),
+				      "reset", GPIOD_OUT_HIGH, "PERST#");
+	if (IS_ERR(reset))
+		return PTR_ERR(reset);
+
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	port->reset = reset;
+	INIT_LIST_HEAD(&port->list);
+	list_add_tail(&port->list, &bridge->ports);
+
+	return 0;
+}
+
+/**
+ * pci_host_common_parse_ports - Parse Root Port nodes from device tree
+ * @dev: Device pointer
+ * @bridge: PCI host bridge
+ *
+ * This function iterates through child nodes of the host bridge and parses
+ * Root Port properties (currently only reset GPIO).
+ *
+ * Returns: 0 on success, -ENOENT if no ports found, other negative error codes
+ * on failure
+ */
+int pci_host_common_parse_ports(struct device *dev, struct pci_host_bridge *bridge)
+{
+	int ret = -ENOENT;
+
+	for_each_available_child_of_node_scoped(dev->of_node, of_port) {
+		if (!of_node_is_type(of_port, "pci"))
+			continue;
+		ret = pci_host_common_parse_port(bridge, of_port);
+		if (ret)
+			return ret;
+	}
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(pci_host_common_parse_ports);
+
 static void gen_pci_unmap_cfg(void *ptr)
 {
 	pci_ecam_free((struct pci_config_window *)ptr);
diff --git a/drivers/pci/controller/pci-host-common.h b/drivers/pci/controller/pci-host-common.h
index b5075d4bd7eb..1de015d10b9f 100644
--- a/drivers/pci/controller/pci-host-common.h
+++ b/drivers/pci/controller/pci-host-common.h
@@ -12,6 +12,21 @@
 
 struct pci_ecam_ops;
 
+/**
+ * struct pci_host_port - Generic Root Port properties
+ * @list: List node for linking multiple ports
+ * @reset: GPIO descriptor for PERST# signal
+ *
+ * This structure contains common properties that can be parsed from
+ * Root Port device tree nodes.
+ */
+struct pci_host_port {
+	struct list_head	list;
+	struct gpio_desc	*reset;
+};
+
+int pci_host_common_parse_ports(struct device *dev, struct pci_host_bridge *bridge);
+
 int pci_host_common_probe(struct platform_device *pdev);
 int pci_host_common_init(struct platform_device *pdev,
 			 struct pci_host_bridge *bridge,
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index bccc7a4bdd79..9cc3f4ebb370 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -647,6 +647,7 @@ static void pci_release_host_bridge_dev(struct device *dev)
 
 	pci_free_resource_list(&bridge->windows);
 	pci_free_resource_list(&bridge->dma_ranges);
+	pci_free_resource_list(&bridge->ports);
 
 	/* Host bridges only have domain_nr set in the emulation case */
 	if (bridge->domain_nr != PCI_DOMAIN_NR_NOT_SET)
@@ -671,6 +672,7 @@ static void pci_init_host_bridge(struct pci_host_bridge *bridge)
 {
 	INIT_LIST_HEAD(&bridge->windows);
 	INIT_LIST_HEAD(&bridge->dma_ranges);
+	INIT_LIST_HEAD(&bridge->ports);
 
 	/*
 	 * We assume we can manage these PCIe features.  Some systems may
diff --git a/include/linux/pci.h b/include/linux/pci.h
index 1c270f1d5123..b05482355abc 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -634,6 +634,7 @@ struct pci_host_bridge {
 	int		domain_nr;
 	struct list_head windows;	/* resource_entry */
 	struct list_head dma_ranges;	/* dma ranges resource list */
+	struct list_head ports;		/* Root Port list (pci_host_port) */
 #ifdef CONFIG_PCI_IDE
 	u16 nr_ide_streams; /* Max streams possibly active in @ide_stream_ida */
 	struct ida ide_stream_ida;
-- 
2.37.1

[PATCH V6 03/12] PCI: dwc: Parse Root Port nodes in dw_pcie_host_init()

[Sherry Sun]

Add support for parsing Root Port child nodes in dw_pcie_host_init()
using pci_host_common_parse_ports(). This allows DWC-based drivers to
specify Root Port properties (like reset GPIOs) in individual Root Port
nodes rather than in the host bridge node.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 drivers/pci/controller/dwc/pcie-designware-host.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
index 6ae6189e9b8a..6ceb146e9a04 100644
--- a/drivers/pci/controller/dwc/pcie-designware-host.c
+++ b/drivers/pci/controller/dwc/pcie-designware-host.c
@@ -20,6 +20,7 @@
 #include <linux/platform_device.h>
 
 #include "../../pci.h"
+#include "../pci-host-common.h"
 #include "pcie-designware.h"
 
 static struct pci_ops dw_pcie_ops;
@@ -581,6 +582,13 @@ int dw_pcie_host_init(struct dw_pcie_rp *pp)
 
 	pp->bridge = bridge;
 
+	/* Parse Root Port nodes if present */
+	ret = pci_host_common_parse_ports(dev, bridge);
+	if (ret && ret != -ENOENT) {
+		dev_err(dev, "Failed to parse Root Port nodes: %d\n", ret);
+		return ret;
+	}
+
 	ret = dw_pcie_host_get_resources(pp);
 	if (ret)
 		return ret;
-- 
2.37.1

[PATCH V6 04/12] PCI: imx6: Add support for parsing the reset property in new Root Port binding

[Sherry Sun]

The current DT binding for pci-imx6 specifies the 'reset-gpios' property
in the host bridge node. However, the PERST# signal logically belongs to
individual Root Ports rather than the host bridge itself. This becomes
important when supporting PCIe KeyE connector and PCI power control
framework for pci-imx6 driver, which requires properties to be specified
in Root Port nodes.

With the common Root Port parsing now handled in dw_pcie_host_init(),
update the reset GPIO handling to use the parsed port list from
bridge->ports. To maintain DT backwards compatibility, fallback to the
legacy method of parsing the host bridge node if the reset property is
not present in the Root Port node (indicated by an empty ports list).

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 drivers/pci/controller/dwc/pci-imx6.c | 76 +++++++++++++++++++++------
 1 file changed, 61 insertions(+), 15 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index a5b8d0b71677..4860575f5005 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -34,6 +34,7 @@
 #include <linux/pm_runtime.h>
 
 #include "../../pci.h"
+#include "../pci-host-common.h"
 #include "pcie-designware.h"
 
 #define IMX8MQ_GPR_PCIE_REF_USE_PAD		BIT(9)
@@ -150,7 +151,6 @@ struct imx_lut_data {
 
 struct imx_pcie {
 	struct dw_pcie		*pci;
-	struct gpio_desc	*reset_gpiod;
 	struct clk_bulk_data	*clks;
 	int			num_clks;
 	bool			supports_clkreq;
@@ -897,29 +897,40 @@ static int imx95_pcie_core_reset(struct imx_pcie *imx_pcie, bool assert)
 
 static void imx_pcie_assert_core_reset(struct imx_pcie *imx_pcie)
 {
+	struct dw_pcie *pci = imx_pcie->pci;
+	struct pci_host_bridge *bridge = pci->pp.bridge;
+	struct pci_host_port *port;
+
 	reset_control_assert(imx_pcie->pciephy_reset);
 
 	if (imx_pcie->drvdata->core_reset)
 		imx_pcie->drvdata->core_reset(imx_pcie, true);
 
 	/* Some boards don't have PCIe reset GPIO. */
-	gpiod_set_value_cansleep(imx_pcie->reset_gpiod, 1);
+	if (bridge)
+		list_for_each_entry(port, &bridge->ports, list)
+			gpiod_set_value_cansleep(port->reset, 1);
 }
 
 static int imx_pcie_deassert_core_reset(struct imx_pcie *imx_pcie)
 {
+	struct dw_pcie *pci = imx_pcie->pci;
+	struct pci_host_bridge *bridge = pci->pp.bridge;
+	struct pci_host_port *port;
+
 	reset_control_deassert(imx_pcie->pciephy_reset);
 
 	if (imx_pcie->drvdata->core_reset)
 		imx_pcie->drvdata->core_reset(imx_pcie, false);
 
 	/* Some boards don't have PCIe reset GPIO. */
-	if (imx_pcie->reset_gpiod) {
-		msleep(100);
-		gpiod_set_value_cansleep(imx_pcie->reset_gpiod, 0);
-		/* Wait for 100ms after PERST# deassertion (PCIe r5.0, 6.6.1) */
-		msleep(100);
-	}
+	if (bridge)
+		list_for_each_entry(port, &bridge->ports, list)
+			if (port->reset) {
+				msleep(PCIE_T_PVPERL_MS);
+				gpiod_set_value_cansleep(port->reset, 0);
+				msleep(PCIE_RESET_CONFIG_WAIT_MS);
+			}
 
 	return 0;
 }
@@ -1233,6 +1244,44 @@ static void imx_pcie_disable_device(struct pci_host_bridge *bridge,
 	imx_pcie_remove_lut(imx_pcie, pci_dev_id(pdev));
 }
 
+static int imx_pcie_parse_legacy_binding(struct imx_pcie *pcie)
+{
+	struct device *dev = pcie->pci->dev;
+	struct pci_host_bridge *bridge = pcie->pci->pp.bridge;
+	struct pci_host_port *port;
+	struct gpio_desc *reset;
+
+	if (!bridge) {
+		dev_err(dev, "Bridge not allocated yet\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * For DT backward compatibility: if no Root Port nodes were parsed
+	 * (indicated by empty ports list), parse reset-gpios from the host
+	 * bridge node.
+	 */
+	if (!list_empty(&bridge->ports))
+		return 0;
+
+	reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(reset))
+		return PTR_ERR(reset);
+
+	if (!reset)
+		return 0;
+
+	port = devm_kzalloc(dev, sizeof(*port), GFP_KERNEL);
+	if (!port)
+		return -ENOMEM;
+
+	port->reset = reset;
+	INIT_LIST_HEAD(&port->list);
+	list_add_tail(&port->list, &bridge->ports);
+
+	return 0;
+}
+
 static int imx_pcie_host_init(struct dw_pcie_rp *pp)
 {
 	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
@@ -1240,6 +1289,10 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
 	struct imx_pcie *imx_pcie = to_imx_pcie(pci);
 	int ret;
 
+	ret = imx_pcie_parse_legacy_binding(imx_pcie);
+	if (ret)
+		return ret;
+
 	if (imx_pcie->vpcie) {
 		ret = regulator_enable(imx_pcie->vpcie);
 		if (ret) {
@@ -1688,13 +1741,6 @@ static int imx_pcie_probe(struct platform_device *pdev)
 			return PTR_ERR(imx_pcie->phy_base);
 	}
 
-	/* Fetch GPIOs */
-	imx_pcie->reset_gpiod = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
-	if (IS_ERR(imx_pcie->reset_gpiod))
-		return dev_err_probe(dev, PTR_ERR(imx_pcie->reset_gpiod),
-				     "unable to get reset gpio\n");
-	gpiod_set_consumer_name(imx_pcie->reset_gpiod, "PCIe reset");
-
 	/* Fetch clocks */
 	imx_pcie->num_clks = devm_clk_bulk_get_all(dev, &imx_pcie->clks);
 	if (imx_pcie->num_clks < 0)
-- 
2.37.1

[PATCH V6 05/12] arm: dts: imx6qdl: Add Root Port node and PERST property

[Sherry Sun]

Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi |  5 +++++
 arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi         | 11 +++++++++++
 arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts |  5 +++++
 3 files changed, 21 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
index ba29720e3f72..fe9046c03ddd 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
@@ -754,11 +754,16 @@ lvds0_out: endpoint {
 &pcie {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie>;
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
 	vpcie-supply = <&reg_pcie>;
 	status = "okay";
 };
 
+&pcie_port0 {
+	reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+};
+
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
index 76e6043e1f91..eeb376193398 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
@@ -289,6 +289,17 @@ pcie: pcie@1ffc000 {
 				 <&clks IMX6QDL_CLK_PCIE_REF_125M>;
 			clock-names = "pcie", "pcie_bus", "pcie_phy";
 			status = "disabled";
+
+			pcie_port0: pcie@0 {
+				compatible = "pciclass,0604";
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
 		aips1: bus@2000000 { /* AIPS1 */
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
index c5b220aeaefd..6b12cab7175f 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
@@ -45,10 +45,15 @@ MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 };
 
 &pcie {
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&max7310_c 5 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
+&pcie_port0 {
+	reset-gpios = <&max7310_c 5 GPIO_ACTIVE_LOW>;
+};
+
 &sata {
 	status = "okay";
 };
-- 
2.37.1

[PATCH V6 06/12] arm: dts: imx6sx: Add Root Port node and PERST property

[Sherry Sun]

Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi |  5 +++++
 arch/arm/boot/dts/nxp/imx/imx6sx.dtsi     | 11 +++++++++++
 2 files changed, 16 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
index 3e238d8118fa..338de4d144b2 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi
@@ -282,11 +282,16 @@ codec: wm8962@1a {
 &pcie {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie>;
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&gpio2 0 GPIO_ACTIVE_LOW>;
 	vpcie-supply = <&reg_pcie_gpio>;
 	status = "okay";
 };
 
+&pcie_port0 {
+	reset-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+};
+
 &lcdif1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcd>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
index 1426f357d474..d42363cb5105 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
@@ -1470,6 +1470,17 @@ pcie: pcie@8ffc000 {
 			power-domains = <&pd_disp>, <&pd_pci>;
 			power-domain-names = "pcie", "pcie_phy";
 			status = "disabled";
+
+			pcie_port0: pcie@0 {
+				compatible = "pciclass,0604";
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 	};
 };
-- 
2.37.1

[PATCH V6 07/12] arm: dts: imx7d: Add Root Port node and PERST property

[Sherry Sun]

Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts |  5 +++++
 arch/arm/boot/dts/nxp/imx/imx7d.dtsi    | 11 +++++++++++
 2 files changed, 16 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts b/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
index a370e868cafe..0046b276b8b9 100644
--- a/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts
@@ -456,10 +456,15 @@ display_out: endpoint {
 };
 
 &pcie {
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&extended_io 1 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
+&pcie_port0 {
+	reset-gpios = <&extended_io 1 GPIO_ACTIVE_LOW>;
+};
+
 &reg_1p0d {
 	vin-supply = <&sw2_reg>;
 };
diff --git a/arch/arm/boot/dts/nxp/imx/imx7d.dtsi b/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
index d961c61a93af..3c5c1f2c1460 100644
--- a/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx7d.dtsi
@@ -155,6 +155,17 @@ pcie: pcie@33800000 {
 			reset-names = "pciephy", "apps", "turnoff";
 			fsl,imx7d-pcie-phy = <&pcie_phy>;
 			status = "disabled";
+
+			pcie_port0: pcie@0 {
+				compatible = "pciclass,0604";
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 	};
 };
-- 
2.37.1

[PATCH V6 08/12] arm64: dts: imx8mm: Add Root Port node and PERST property

[Sherry Sun]

Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi |  5 +++++
 arch/arm64/boot/dts/freescale/imx8mm.dtsi     | 11 +++++++++++
 2 files changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
index 6eab8a6001db..060860f24e7a 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
@@ -533,6 +533,7 @@ &pcie_phy {
 &pcie0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie0>;
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&gpio4 21 GPIO_ACTIVE_LOW>;
 	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&pcie0_refclk>,
 		 <&clk IMX8MM_CLK_PCIE1_AUX>;
@@ -559,6 +560,10 @@ &pcie0_ep {
 	status = "disabled";
 };
 
+&pcie0_port0 {
+	reset-gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
+};
+
 &sai2 {
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index 9f49c0b386d3..1204cc4d3f37 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -1369,6 +1369,17 @@ pcie0: pcie@33800000 {
 			phys = <&pcie_phy>;
 			phy-names = "pcie-phy";
 			status = "disabled";
+
+			pcie0_port0: pcie@0 {
+				compatible = "pciclass,0604";
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
 		pcie0_ep: pcie-ep@33800000 {
-- 
2.37.1

[PATCH V6 09/12] arm64: dts: imx8mp: Add Root Port node and PERST property

[Sherry Sun]

Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mp-evk.dts |  5 +++++
 arch/arm64/boot/dts/freescale/imx8mp.dtsi    | 11 +++++++++++
 2 files changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
index 50850cb6d287..dfcdcc739ec6 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
@@ -769,6 +769,7 @@ &pcie_phy {
 &pcie0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie0>;
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&gpio2 7 GPIO_ACTIVE_LOW>;
 	vpcie-supply = <&reg_pcie0>;
 	vpcie3v3aux-supply = <&reg_pcie0>;
@@ -782,6 +783,10 @@ &pcie0_ep {
 	status = "disabled";
 };
 
+&pcie0_port0 {
+	reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+};
+
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
index 9b2b3a9bf9e8..f66667735a02 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -2266,6 +2266,17 @@ pcie0: pcie: pcie@33800000 {
 			phys = <&pcie_phy>;
 			phy-names = "pcie-phy";
 			status = "disabled";
+
+			pcie0_port0: pcie@0 {
+				compatible = "pciclass,0604";
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
 		pcie0_ep: pcie_ep: pcie-ep@33800000 {
-- 
2.37.1

[PATCH V6 10/12] arm64: dts: imx8mq: Add Root Port node and PERST property

[Sherry Sun]

Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 10 +++++++++
 arch/arm64/boot/dts/freescale/imx8mq.dtsi    | 22 ++++++++++++++++++++
 2 files changed, 32 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
index d48f901487d4..e7d87ea81b69 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
@@ -369,6 +369,7 @@ mipi_dsi_out: endpoint {
 &pcie0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie0>;
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&gpio5 28 GPIO_ACTIVE_LOW>;
 	clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
 		 <&pcie0_refclk>,
@@ -389,9 +390,14 @@ &pcie0_ep {
 	status = "disabled";
 };
 
+&pcie0_port0 {
+	reset-gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
+};
+
 &pcie1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie1>;
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&gpio5 12 GPIO_ACTIVE_LOW>;
 	clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
 		 <&pcie0_refclk>,
@@ -414,6 +420,10 @@ &pcie1_ep {
 	status = "disabled";
 };
 
+&pcie1_port0 {
+	reset-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+};
+
 &pgc_gpu {
 	power-supply = <&sw1a_reg>;
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 607962f807be..de2ba4ee9da6 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -1768,6 +1768,17 @@ pcie0: pcie@33800000 {
 			assigned-clock-rates = <250000000>, <100000000>,
 			                       <10000000>;
 			status = "disabled";
+
+			pcie0_port0: pcie@0 {
+				compatible = "pciclass,0604";
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
 		pcie0_ep: pcie-ep@33800000 {
@@ -1846,6 +1857,17 @@ pcie1: pcie@33c00000 {
 			assigned-clock-rates = <250000000>, <100000000>,
 			                       <10000000>;
 			status = "disabled";
+
+			pcie1_port0: pcie@0 {
+				compatible = "pciclass,0604";
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
 		pcie1_ep: pcie-ep@33c00000 {
-- 
2.37.1

[PATCH V6 11/12] arm64: dts: imx8dxl/qm/qxp: Add Root Port node and PERST property

[Sherry Sun]

Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 .../boot/dts/freescale/imx8-ss-hsio.dtsi      | 11 ++++++++++
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts |  5 +++++
 arch/arm64/boot/dts/freescale/imx8qm-mek.dts  | 10 +++++++++
 .../boot/dts/freescale/imx8qm-ss-hsio.dtsi    | 22 +++++++++++++++++++
 arch/arm64/boot/dts/freescale/imx8qxp-mek.dts |  5 +++++
 5 files changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi
index 469de8b536b5..009990b2e559 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-hsio.dtsi
@@ -78,6 +78,17 @@ pcieb: pcie@5f010000 {
 		power-domains = <&pd IMX_SC_R_PCIE_B>;
 		fsl,max-link-speed = <3>;
 		status = "disabled";
+
+		pcieb_port0: pcie@0 {
+			compatible = "pciclass,0604";
+			device_type = "pci";
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			bus-range = <0x01 0xff>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+		};
 	};
 
 	pcieb_ep: pcie-ep@5f010000 {
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
index 5c68d33e19f2..8f2c2bd00cde 100644
--- a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
@@ -651,6 +651,7 @@ &pcie0 {
 	phy-names = "pcie-phy";
 	pinctrl-0 = <&pinctrl_pcieb>;
 	pinctrl-names = "default";
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
 	vpcie-supply = <&reg_pcieb>;
 	vpcie3v3aux-supply = <&reg_pcieb>;
@@ -667,6 +668,10 @@ &pcie0_ep {
 	status = "disabled";
 };
 
+&pcieb_port0 {
+	reset-gpios = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
+};
+
 &sai0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sai0>;
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index dadc136aec6e..02f7589bd860 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -802,6 +802,7 @@ &pciea {
 	phy-names = "pcie-phy";
 	pinctrl-0 = <&pinctrl_pciea>;
 	pinctrl-names = "default";
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&lsio_gpio4 29 GPIO_ACTIVE_LOW>;
 	vpcie-supply = <&reg_pciea>;
 	vpcie3v3aux-supply = <&reg_pciea>;
@@ -809,15 +810,24 @@ &pciea {
 	status = "okay";
 };
 
+&pciea_port0 {
+	reset-gpios = <&lsio_gpio4 29 GPIO_ACTIVE_LOW>;
+};
+
 &pcieb {
 	phys = <&hsio_phy 1 PHY_TYPE_PCIE 1>;
 	phy-names = "pcie-phy";
 	pinctrl-0 = <&pinctrl_pcieb>;
 	pinctrl-names = "default";
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&lsio_gpio5 0 GPIO_ACTIVE_LOW>;
 	status = "disabled";
 };
 
+&pcieb_port0 {
+	reset-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_LOW>;
+};
+
 &qm_pwm_lvds0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm_lvds0>;
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi
index bd6e0aa27efe..48c29c2cfe8b 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-hsio.dtsi
@@ -40,6 +40,17 @@ pcie0: pciea: pcie@5f000000 {
 		power-domains = <&pd IMX_SC_R_PCIE_A>;
 		fsl,max-link-speed = <3>;
 		status = "disabled";
+
+		pciea_port0: pcie@0 {
+			compatible = "pciclass,0604";
+			device_type = "pci";
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			bus-range = <0x01 0xff>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+		};
 	};
 
 	pcie0_ep: pciea_ep: pcie-ep@5f000000 {
@@ -90,6 +101,17 @@ pcie1: pcieb: pcie@5f010000 {
 		power-domains = <&pd IMX_SC_R_PCIE_B>;
 		fsl,max-link-speed = <3>;
 		status = "disabled";
+
+		pcieb_port0: pcie@0 {
+			compatible = "pciclass,0604";
+			device_type = "pci";
+			reg = <0x0 0x0 0x0 0x0 0x0>;
+			bus-range = <0x01 0xff>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+		};
 	};
 
 	sata: sata@5f020000 {
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
index 40a0bc9f4e84..cd127d0a0a75 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
@@ -722,6 +722,7 @@ &pcie0 {
 	phy-names = "pcie-phy";
 	pinctrl-0 = <&pinctrl_pcieb>;
 	pinctrl-names = "default";
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpios = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
 	vpcie-supply = <&reg_pcieb>;
 	vpcie3v3aux-supply = <&reg_pcieb>;
@@ -738,6 +739,10 @@ &pcie0_ep {
 	status = "disabled";
 };
 
+&pcieb_port0 {
+	reset-gpios = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
+};
+
 &scu_key {
 	status = "okay";
 };
-- 
2.37.1

[PATCH V6 12/12] arm64: dts: imx95: Add Root Port node and PERST property

[Sherry Sun]

Since describing the PCIe PERST# property under Host Bridge node is now
deprecated, it is recommended to add it to the Root Port node, so
creating the Root Port node and add the reset-gpios property in Root
Port.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 .../boot/dts/freescale/imx95-15x15-evk.dts    |  5 +++++
 .../boot/dts/freescale/imx95-19x19-evk.dts    | 10 +++++++++
 arch/arm64/boot/dts/freescale/imx95.dtsi      | 22 +++++++++++++++++++
 3 files changed, 37 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts b/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts
index d4184fb8b28c..42bc09e48b80 100644
--- a/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-15x15-evk.dts
@@ -554,6 +554,7 @@ &netcmix_blk_ctrl {
 &pcie0 {
 	pinctrl-0 = <&pinctrl_pcie0>;
 	pinctrl-names = "default";
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&gpio5 13 GPIO_ACTIVE_LOW>;
 	vpcie-supply = <&reg_m2_pwr>;
 	vpcie3v3aux-supply = <&reg_m2_pwr>;
@@ -568,6 +569,10 @@ &pcie0_ep {
 	status = "disabled";
 };
 
+&pcie0_port0 {
+	reset-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+};
+
 &sai1 {
 	assigned-clocks = <&scmi_clk IMX95_CLK_AUDIOPLL1_VCO>,
 			  <&scmi_clk IMX95_CLK_AUDIOPLL2_VCO>,
diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
index 041fd838fabb..6f193cf04119 100644
--- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
@@ -540,6 +540,7 @@ &netc_timer {
 &pcie0 {
 	pinctrl-0 = <&pinctrl_pcie0>;
 	pinctrl-names = "default";
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&i2c7_pcal6524 5 GPIO_ACTIVE_LOW>;
 	vpcie-supply = <&reg_pcie0>;
 	vpcie3v3aux-supply = <&reg_pcie0>;
@@ -554,9 +555,14 @@ &pcie0_ep {
 	status = "disabled";
 };
 
+&pcie0_port0 {
+	reset-gpios = <&i2c7_pcal6524 5 GPIO_ACTIVE_LOW>;
+};
+
 &pcie1 {
 	pinctrl-0 = <&pinctrl_pcie1>;
 	pinctrl-names = "default";
+	/* This property is deprecated, use reset-gpios from the Root Port node. */
 	reset-gpio = <&i2c7_pcal6524 16 GPIO_ACTIVE_LOW>;
 	vpcie-supply = <&reg_slot_pwr>;
 	vpcie3v3aux-supply = <&reg_slot_pwr>;
@@ -570,6 +576,10 @@ &pcie1_ep {
 	status = "disabled";
 };
 
+&pcie1_port0 {
+	reset-gpios = <&i2c7_pcal6524 16 GPIO_ACTIVE_LOW>;
+};
+
 &sai1 {
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/freescale/imx95.dtsi b/arch/arm64/boot/dts/freescale/imx95.dtsi
index 55e2da094c88..7c5f350fe3a4 100644
--- a/arch/arm64/boot/dts/freescale/imx95.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx95.dtsi
@@ -1883,6 +1883,17 @@ pcie0: pcie@4c300000 {
 			iommu-map-mask = <0x1ff>;
 			fsl,max-link-speed = <3>;
 			status = "disabled";
+
+			pcie0_port0: pcie@0 {
+				compatible = "pciclass,0604";
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
 		pcie0_ep: pcie-ep@4c300000 {
@@ -1960,6 +1971,17 @@ pcie1: pcie@4c380000 {
 			iommu-map-mask = <0x1ff>;
 			fsl,max-link-speed = <3>;
 			status = "disabled";
+
+			pcie1_port0: pcie@0 {
+				compatible = "pciclass,0604";
+				device_type = "pci";
+				reg = <0x0 0x0 0x0 0x0 0x0>;
+				bus-range = <0x01 0xff>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+				ranges;
+			};
 		};
 
 		pcie1_ep: pcie-ep@4c380000 {
-- 
2.37.1

Re: [PATCH V6 00/12] pci-imx6: Add support for parsing the reset property in new Root Port binding

[Manivannan Sadhasivam]

On Wed, Feb 25, 2026 at 06:55:11PM +0800, Sherry Sun wrote:
> This patch set adds support for parsing the reset property in new Root Port
> binding in pci-imx6 driver, similar to the implementation in the qcom pcie
> driver[1].
> 
> Also introduce generic helper functions to parse Root Port device tree
> nodes and extract common properties like reset GPIOs. This allows multiple
> PCI host controller drivers to share the same parsing logic.
> 
> Define struct pci_host_port to hold common Root Port properties
> (currently only reset GPIO descriptor) and add
> pci_host_common_parse_ports() to parse Root Port nodes from device tree.
> Also add the 'ports' list to struct pci_host_bridge for better maintain
> parsed Root Port information.
> 
> The plan is to add the wake-gpio property to the root port in subsequent
> patches. Also, the vpcie-supply property will be moved to the root port
> node later based on the refactoring patch set for the PCI pwrctrl
> framework[2]. 
> 
> The initial idea is to adopt the Manivannan’s recent PCIe M.2 KeyE
> connector support patch set[3] and PCI power control framework patches[2],
> and extend them to the pcie-imx6 driver. Since the new M.2/pwrctrl model is
> implemented based on Root Ports and requires the pwrctrl driver to bind to
> a Root Port device, we need to introduce a Root Port child node on i.MX
> boards that provide an M.2 connector.
> 
> To follow a more standardized DT structure, it also makes sense to move
> the reset-gpios and wake-gpios properties into the Root Port node. These
> signals logically belong to the Root Port rather than the host bridge,
> and placing them there aligns with the new M.2/pwrctrl model.
> 
> Regarding backward compatibility, as Frank suggested, I will not remove
> the old reset-gpio property from existing DTS files to avoid function
> break.
> 
> For new i.MX platforms — such as the upcoming i.MX952-evk will add
> vpcie-supply, reset-gpios, and wake-gpios directly under the Root Port
> node.
> Therefore, driver updates are needed to support both the legacy
> properties and the new standardized Root Port based layout.
> 
> [1] https://lore.kernel.org/linux-pci/20250702-perst-v5-0-920b3d1f6ee1@qti.qualcomm.com/
> [2] https://lore.kernel.org/linux-pci/20260115-pci-pwrctrl-rework-v5-0-9d26da3ce903@oss.qualcomm.com/
> [3] https://lore.kernel.org/linux-pci/20260112-pci-m2-e-v4-0-eff84d2c6d26@oss.qualcomm.com/
> 
> Signed-off-by: Sherry Sun <sherry.sun@nxp.com>

Please do not send next version before closing or even giving a window.

- Mani

> ---
> Changes in V6:
> 1. Drop the pre-allocate pci_host_bridge struct changes in dw_pcie_host_init()
>    and imx_pcie_probe().
> 2. Parse Root Port nodes in dw_pcie_host_init() as Frank and Mani suggested.
> 3. Move the imx_pcie_parse_legacy_binding() from imx_pcie_probe() to
>    imx_pcie_host_init(), so that dw_pcie_host_init() parse Root Port first, if
>    no Root Port nodes were parsed(indicated by empty ports list), then parse
>    legacy binding.
> 4. Add device pointer parameter for pci_host_common_parse_ports().
> 5. Add NULL pointer check for reset gpio in imx_pcie_parse_legacy_binding().
> 
> Changes in V5:
> 1. Add the Root Port list(pci_host_port) to struct pci_host_bridge for better
>    maintain parsed Root Port information.
> 2. Delete the pci_host_common_delete_ports() as now the Root Port list in
>    pci_host_bridge can be cleared by pci_release_host_bridge_dev().
> 3. Change the common API pci_host_common_parse_ports() pass down struct
>    pci_host_bridge *. 
> 4. Modify dw_pcie_host_init() to allow drivers to pre-allocate pci_host_bridge
>    struct when needed.
> 5. Allocate bridge early in imx_pcie_probe() to parse Root Ports.
> 
> Changes in V4:
> 1. Add common helpers for parsing Root Port properties in pci-host-common.c in
>    patch#2.
> 2. Call common pci_host_common_parse_ports() and pci_host_common_delete_ports()
>    in pci-imx6 driver.
> 3. Use PCIE_T_PVPERL_MS and PCIE_RESET_CONFIG_WAIT_MS instead of magic number
>    100 in patch#3 as Manivannan suggested.
> 4. Use "PERST#" instead of "PCIe reset" for the reset gpio lable in patch#3.
> 
> Changes in V3:
> 1. Improve the patch#2 commit message as Frank suggested.
> 2. Add Reviewed-by tag for patch#1.
> 
> Changes in V2:
> 1. Improve the patch#1 commit message as Frank suggested.
> 2. Also mark the reset-gpio-active-high property as deprecated in
>    imx6q-pcie DT binding as Rob suggested.
> 3. The imx_pcie_delete_ports() has been moved up so that the
>    imx_pcie_parse_ports() can call this helper function in error handling.
> 4. Keep the old reset-gpio property in the host bridge node for the
>    existing dts files and add comments to avoid confusion.
> ---
> 
> Sherry Sun (12):
>   dt-bindings: PCI: fsl,imx6q-pcie: Add reset GPIO in Root Port node
>   PCI: host-generic: Add common helpers for parsing Root Port properties
>   PCI: dwc: Parse Root Port nodes in dw_pcie_host_init()
>   PCI: imx6: Add support for parsing the reset property in new Root Port
>     binding
>   arm: dts: imx6qdl: Add Root Port node and PERST property
>   arm: dts: imx6sx: Add Root Port node and PERST property
>   arm: dts: imx7d: Add Root Port node and PERST property
>   arm64: dts: imx8mm: Add Root Port node and PERST property
>   arm64: dts: imx8mp: Add Root Port node and PERST property
>   arm64: dts: imx8mq: Add Root Port node and PERST property
>   arm64: dts: imx8dxl/qm/qxp: Add Root Port node and PERST property
>   arm64: dts: imx95: Add Root Port node and PERST property
> 
>  .../bindings/pci/fsl,imx6q-pcie.yaml          | 32 ++++++++
>  .../arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi |  5 ++
>  arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi        | 11 +++
>  .../arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts |  5 ++
>  arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi     |  5 ++
>  arch/arm/boot/dts/nxp/imx/imx6sx.dtsi         | 11 +++
>  arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts       |  5 ++
>  arch/arm/boot/dts/nxp/imx/imx7d.dtsi          | 11 +++
>  .../boot/dts/freescale/imx8-ss-hsio.dtsi      | 11 +++
>  arch/arm64/boot/dts/freescale/imx8dxl-evk.dts |  5 ++
>  arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi |  5 ++
>  arch/arm64/boot/dts/freescale/imx8mm.dtsi     | 11 +++
>  arch/arm64/boot/dts/freescale/imx8mp-evk.dts  |  5 ++
>  arch/arm64/boot/dts/freescale/imx8mp.dtsi     | 11 +++
>  arch/arm64/boot/dts/freescale/imx8mq-evk.dts  | 10 +++
>  arch/arm64/boot/dts/freescale/imx8mq.dtsi     | 22 ++++++
>  arch/arm64/boot/dts/freescale/imx8qm-mek.dts  | 10 +++
>  .../boot/dts/freescale/imx8qm-ss-hsio.dtsi    | 22 ++++++
>  arch/arm64/boot/dts/freescale/imx8qxp-mek.dts |  5 ++
>  .../boot/dts/freescale/imx95-15x15-evk.dts    |  5 ++
>  .../boot/dts/freescale/imx95-19x19-evk.dts    | 10 +++
>  arch/arm64/boot/dts/freescale/imx95.dtsi      | 22 ++++++
>  drivers/pci/controller/dwc/pci-imx6.c         | 76 +++++++++++++++----
>  .../pci/controller/dwc/pcie-designware-host.c |  8 ++
>  drivers/pci/controller/pci-host-common.c      | 58 ++++++++++++++
>  drivers/pci/controller/pci-host-common.h      | 15 ++++
>  drivers/pci/probe.c                           |  2 +
>  include/linux/pci.h                           |  1 +
>  28 files changed, 384 insertions(+), 15 deletions(-)
> 
> -- 
> 2.37.1
> 

-- 
மணிவண்ணன் சதாசிவம்

RE: [PATCH V6 00/12] pci-imx6: Add support for parsing the reset property in new Root Port binding

[Sherry Sun]

> Subject: Re: [PATCH V6 00/12] pci-imx6: Add support for parsing the reset
> property in new Root Port binding
> 
> On Wed, Feb 25, 2026 at 06:55:11PM +0800, Sherry Sun wrote:
> > This patch set adds support for parsing the reset property in new Root
> > Port binding in pci-imx6 driver, similar to the implementation in the
> > qcom pcie driver[1].
> >
> > Also introduce generic helper functions to parse Root Port device tree
> > nodes and extract common properties like reset GPIOs. This allows
> > multiple PCI host controller drivers to share the same parsing logic.
> >
> > Define struct pci_host_port to hold common Root Port properties
> > (currently only reset GPIO descriptor) and add
> > pci_host_common_parse_ports() to parse Root Port nodes from device
> tree.
> > Also add the 'ports' list to struct pci_host_bridge for better
> > maintain parsed Root Port information.
> >
> > The plan is to add the wake-gpio property to the root port in
> > subsequent patches. Also, the vpcie-supply property will be moved to
> > the root port node later based on the refactoring patch set for the
> > PCI pwrctrl framework[2].
> >
> > The initial idea is to adopt the Manivannan’s recent PCIe M.2 KeyE
> > connector support patch set[3] and PCI power control framework
> > patches[2], and extend them to the pcie-imx6 driver. Since the new
> > M.2/pwrctrl model is implemented based on Root Ports and requires the
> > pwrctrl driver to bind to a Root Port device, we need to introduce a
> > Root Port child node on i.MX boards that provide an M.2 connector.
> >
> > To follow a more standardized DT structure, it also makes sense to
> > move the reset-gpios and wake-gpios properties into the Root Port
> > node. These signals logically belong to the Root Port rather than the
> > host bridge, and placing them there aligns with the new M.2/pwrctrl model.
> >
> > Regarding backward compatibility, as Frank suggested, I will not
> > remove the old reset-gpio property from existing DTS files to avoid
> > function break.
> >
> > For new i.MX platforms — such as the upcoming i.MX952-evk will add
> > vpcie-supply, reset-gpios, and wake-gpios directly under the Root Port
> > node.
> > Therefore, driver updates are needed to support both the legacy
> > properties and the new standardized Root Port based layout.
> >
> > [1]
> > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flore
> > .kernel.org%2Flinux-pci%2F20250702-perst-v5-0-920b3d1f6ee1%40qti.qualc
> >
> omm.com%2F&data=05%7C02%7Csherry.sun%40nxp.com%7C45ad939b00ee
> 49dc95530
> >
> 8de74707409%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C63907
> 62234966
> >
> 08878%7CUnknown%7CTWFpbGZsb3d8eyJFbXB0eU1hcGkiOnRydWUsIlYiOiI
> wLjAuMDAw
> >
> MCIsIlAiOiJXaW4zMiIsIkFOIjoiTWFpbCIsIldUIjoyfQ%3D%3D%7C0%7C%7C%7C
> &sdat
> >
> a=DpBA%2FzMVVWBnv6CYX%2BFNVcvkE%2B%2FqrRLxpO5B6M4%2BGEA%3
> D&reserved=0
> > [2]
> > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flore
> > .kernel.org%2Flinux-pci%2F20260115-pci-pwrctrl-rework-v5-0-9d26da3ce90
> >
> 3%40oss.qualcomm.com%2F&data=05%7C02%7Csherry.sun%40nxp.com%7C
> 45ad939b
> >
> 00ee49dc955308de74707409%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0
> %7C0%7C
> >
> 639076223496632453%7CUnknown%7CTWFpbGZsb3d8eyJFbXB0eU1hcGkiOn
> RydWUsIlY
> >
> iOiIwLjAuMDAwMCIsIlAiOiJXaW4zMiIsIkFOIjoiTWFpbCIsIldUIjoyfQ%3D%3D%
> 7C0%
> >
> 7C%7C%7C&sdata=NIB0nG8cabdGEDSIRyPwplVtLoF18N5747IOUg5wj3s%3D&
> reserved
> > =0 [3]
> > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2Flore
> > .kernel.org%2Flinux-pci%2F20260112-pci-m2-e-v4-0-
> eff84d2c6d26%40oss.qu
> >
> alcomm.com%2F&data=05%7C02%7Csherry.sun%40nxp.com%7C45ad939b0
> 0ee49dc95
> >
> 5308de74707409%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C63
> 90762234
> >
> 96641988%7CUnknown%7CTWFpbGZsb3d8eyJFbXB0eU1hcGkiOnRydWUsIlYi
> OiIwLjAuM
> >
> DAwMCIsIlAiOiJXaW4zMiIsIkFOIjoiTWFpbCIsIldUIjoyfQ%3D%3D%7C0%7C%7
> C%7C&s
> >
> data=nVlsou%2F9GBR4JW391xJfhFVgW9f8gdc22VVrICNxDKM%3D&reserved=
> 0
> >
> > Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
> 
> Please do not send next version before closing or even giving a window.
> 

Hi Manivannan, sorry, will pay attention next time.
Will check and close all comments for V5 and V6 before sending next version.

Best Regards
Sherry
> 
> > ---
> > Changes in V6:
> > 1. Drop the pre-allocate pci_host_bridge struct changes in
> dw_pcie_host_init()
> >    and imx_pcie_probe().
> > 2. Parse Root Port nodes in dw_pcie_host_init() as Frank and Mani
> suggested.
> > 3. Move the imx_pcie_parse_legacy_binding() from imx_pcie_probe() to
> >    imx_pcie_host_init(), so that dw_pcie_host_init() parse Root Port first, if
> >    no Root Port nodes were parsed(indicated by empty ports list), then parse
> >    legacy binding.
> > 4. Add device pointer parameter for pci_host_common_parse_ports().
> > 5. Add NULL pointer check for reset gpio in
> imx_pcie_parse_legacy_binding().
> >
> > Changes in V5:
> > 1. Add the Root Port list(pci_host_port) to struct pci_host_bridge for better
> >    maintain parsed Root Port information.
> > 2. Delete the pci_host_common_delete_ports() as now the Root Port list in
> >    pci_host_bridge can be cleared by pci_release_host_bridge_dev().
> > 3. Change the common API pci_host_common_parse_ports() pass down
> struct
> >    pci_host_bridge *.
> > 4. Modify dw_pcie_host_init() to allow drivers to pre-allocate
> pci_host_bridge
> >    struct when needed.
> > 5. Allocate bridge early in imx_pcie_probe() to parse Root Ports.
> >
> > Changes in V4:
> > 1. Add common helpers for parsing Root Port properties in pci-host-
> common.c in
> >    patch#2.
> > 2. Call common pci_host_common_parse_ports() and
> pci_host_common_delete_ports()
> >    in pci-imx6 driver.
> > 3. Use PCIE_T_PVPERL_MS and PCIE_RESET_CONFIG_WAIT_MS instead of
> magic number
> >    100 in patch#3 as Manivannan suggested.
> > 4. Use "PERST#" instead of "PCIe reset" for the reset gpio lable in patch#3.
> >
> > Changes in V3:
> > 1. Improve the patch#2 commit message as Frank suggested.
> > 2. Add Reviewed-by tag for patch#1.
> >
> > Changes in V2:
> > 1. Improve the patch#1 commit message as Frank suggested.
> > 2. Also mark the reset-gpio-active-high property as deprecated in
> >    imx6q-pcie DT binding as Rob suggested.
> > 3. The imx_pcie_delete_ports() has been moved up so that the
> >    imx_pcie_parse_ports() can call this helper function in error handling.
> > 4. Keep the old reset-gpio property in the host bridge node for the
> >    existing dts files and add comments to avoid confusion.
> > ---
> >
> > Sherry Sun (12):
> >   dt-bindings: PCI: fsl,imx6q-pcie: Add reset GPIO in Root Port node
> >   PCI: host-generic: Add common helpers for parsing Root Port properties
> >   PCI: dwc: Parse Root Port nodes in dw_pcie_host_init()
> >   PCI: imx6: Add support for parsing the reset property in new Root Port
> >     binding
> >   arm: dts: imx6qdl: Add Root Port node and PERST property
> >   arm: dts: imx6sx: Add Root Port node and PERST property
> >   arm: dts: imx7d: Add Root Port node and PERST property
> >   arm64: dts: imx8mm: Add Root Port node and PERST property
> >   arm64: dts: imx8mp: Add Root Port node and PERST property
> >   arm64: dts: imx8mq: Add Root Port node and PERST property
> >   arm64: dts: imx8dxl/qm/qxp: Add Root Port node and PERST property
> >   arm64: dts: imx95: Add Root Port node and PERST property
> >
> >  .../bindings/pci/fsl,imx6q-pcie.yaml          | 32 ++++++++
> >  .../arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi |  5 ++
> >  arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi        | 11 +++
> >  .../arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts |  5 ++
> >  arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi     |  5 ++
> >  arch/arm/boot/dts/nxp/imx/imx6sx.dtsi         | 11 +++
> >  arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts       |  5 ++
> >  arch/arm/boot/dts/nxp/imx/imx7d.dtsi          | 11 +++
> >  .../boot/dts/freescale/imx8-ss-hsio.dtsi      | 11 +++
> >  arch/arm64/boot/dts/freescale/imx8dxl-evk.dts |  5 ++
> > arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi |  5 ++
> >  arch/arm64/boot/dts/freescale/imx8mm.dtsi     | 11 +++
> >  arch/arm64/boot/dts/freescale/imx8mp-evk.dts  |  5 ++
> >  arch/arm64/boot/dts/freescale/imx8mp.dtsi     | 11 +++
> >  arch/arm64/boot/dts/freescale/imx8mq-evk.dts  | 10 +++
> >  arch/arm64/boot/dts/freescale/imx8mq.dtsi     | 22 ++++++
> >  arch/arm64/boot/dts/freescale/imx8qm-mek.dts  | 10 +++
> >  .../boot/dts/freescale/imx8qm-ss-hsio.dtsi    | 22 ++++++
> >  arch/arm64/boot/dts/freescale/imx8qxp-mek.dts |  5 ++
> >  .../boot/dts/freescale/imx95-15x15-evk.dts    |  5 ++
> >  .../boot/dts/freescale/imx95-19x19-evk.dts    | 10 +++
> >  arch/arm64/boot/dts/freescale/imx95.dtsi      | 22 ++++++
> >  drivers/pci/controller/dwc/pci-imx6.c         | 76 +++++++++++++++----
> >  .../pci/controller/dwc/pcie-designware-host.c |  8 ++
> >  drivers/pci/controller/pci-host-common.c      | 58 ++++++++++++++
> >  drivers/pci/controller/pci-host-common.h      | 15 ++++
> >  drivers/pci/probe.c                           |  2 +
> >  include/linux/pci.h                           |  1 +
> >  28 files changed, 384 insertions(+), 15 deletions(-)
> >
> > --
> > 2.37.1
> >
> 
> --
> மணிவண்ணன் சதாசிவம்