[PATCH 0/3] Add Variscite i.MX6UL SoM and Concerto board support

[PATCH 0/3] Add Variscite i.MX6UL SoM and Concerto board support

[Antonin Godard]

This patch series adds support for the i.MX6UL Variscite SoM
(VAR-SOM-6UL) and the Variscite Concerto Carrier Board.

I tested this with a VAR-SOM-6UL_G2_700C_512R_8N_IT_REV1.3A (one variant
of this SoM), meaning I couldn't test all of the possible options of the
SoM - so this device tree includes partial support for it.

These are based on the 5.15 Variscite kernel fork but adapted for
mainline.

Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
---
Antonin Godard (3):
      dt-bindings: arm: fsl: Add VAR-SOM-MX6UL SoM and Concerto board
      ARM: dts: imx6ul: Add Variscite VAR-SOM-MX6UL SoM support
      ARM: dts: imx6ul: Add Variscite Concerto board support

 Documentation/devicetree/bindings/arm/fsl.yaml     |   6 +
 arch/arm/boot/dts/nxp/imx/Makefile                 |   1 +
 .../boot/dts/nxp/imx/imx6ul-var-som-concerto.dts   | 331 +++++++++++++++++++++
 arch/arm/boot/dts/nxp/imx/imx6ul-var-som.dtsi      | 232 +++++++++++++++
 4 files changed, 570 insertions(+)
---
base-commit: ffd294d346d185b70e28b1a28abe367bbfe53c04
change-id: 20250120-varsom6ul-concerto-dts-a08be2a6219b

Best regards,
-- 
Antonin Godard <antonin.godard@bootlin.com>

[PATCH 1/3] dt-bindings: arm: fsl: Add VAR-SOM-MX6UL SoM and Concerto board

[Antonin Godard]

Add support for the Variscite i.MX6UL VAR-SOM-MX6UL and the Variscite
Concerto carrier board.

Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 6e0dcf4307f10040dafd96b8e12079813e414c08..5c1a27884f0d7ab0c7adc307ff502e179f85523f 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -402,6 +402,12 @@ properties:
           - const: variscite,var-som-imx6q
           - const: fsl,imx6q
 
+      - description: i.MX6UL Variscite VAR-SOM-MX6 Boards
+        items:
+          - const: variscite,mx6concerto
+          - const: variscite,var-som-imx6ul
+          - const: fsl,imx6ul
+
       - description: TQ-Systems TQMa6Q SoM (variant A) on MBa6x
         items:
           - const: tq,imx6q-mba6x-a

-- 
2.47.0.2.g7caf9f4c55.dirty

Re: [PATCH 1/3] dt-bindings: arm: fsl: Add VAR-SOM-MX6UL SoM and Concerto board

[Krzysztof Kozlowski]

On 21/01/2025 10:33, Antonin Godard wrote:
> Add support for the Variscite i.MX6UL VAR-SOM-MX6UL and the Variscite
> Concerto carrier board.
> 
> Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
> ---
>  Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
>  1 file changed, 6 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index 6e0dcf4307f10040dafd96b8e12079813e414c08..5c1a27884f0d7ab0c7adc307ff502e179f85523f 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -402,6 +402,12 @@ properties:
>            - const: variscite,var-som-imx6q
>            - const: fsl,imx6q
>  
> +      - description: i.MX6UL Variscite VAR-SOM-MX6 Boards
> +        items:
> +          - const: variscite,mx6concerto
> +          - const: variscite,var-som-imx6ul
> +          - const: fsl,imx6ul

You placed this just between two imx6q entries, so no, keep the order
instead of inserting randomly.

> +
>        - description: TQ-Systems TQMa6Q SoM (variant A) on MBa6x
>          items:
>            - const: tq,imx6q-mba6x-a
Best regards,
Krzysztof

[PATCH 2/3] ARM: dts: imx6ul: Add Variscite VAR-SOM-MX6UL SoM support

[Antonin Godard]

This patch adds support for the Variscite VAR_SOM-MX6UL SoM with :
- NXP i.MX6 UltraLite SoC
- 128–1024 MB DDR3L
- 8–128 GB eMMC
- 128–512 MB SLC NAND
- Camera Interface
- LVDS / Parallel RGB interfaces (not configured)
- Touch controller (not configured)
- Ethernet RMII interface (not configured)
- On-SoM Wi-Fi/Bluetooth with CYW43353 on SDIO Module (not configured)
- SD/MMC/SDIO interface
- USB Host + USB OTG interface
- I2C interfaces
- SPI interfaces
- PCI-Express 2.0 interface
- on-SoM Audio Codec (not configured)
- S/PDIF interface (not configured)

Product website: https://www.variscite.com/product/system-on-module-som/cortex-a7/var-som-6ul-nxp-imx6ul-6ull-6ulz

Support is handled with a SoM-centric dtsi exporting the default
interfaces along the default pinmuxing to be enabled by the board dts
file.

I tested this on a VAR-SOM-6UL_G2_700C_512R_8N_IT_REV1.3A, which is why
some of the features above are mentioned as "not configured" (I couldn't
test them).

This file is based on the one provided by Variscite on their own kernel,
but adapted for mainline.

Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-var-som.dtsi | 232 ++++++++++++++++++++++++++
 1 file changed, 232 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-var-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..6eda5726f2f17acfc5f705b9de524f8195c63845
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som.dtsi
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Support for Variscite VAR-SOM-MX6UL Module
+ *
+ * Copyright 2019 Variscite Ltd.
+ * Copyright 2025 Bootlin
+ */
+
+/dts-v1/;
+
+#include "imx6ul.dtsi"
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Variscite VAR-SOM-MX6UL module";
+	compatible = "variscite,var-som-imx6ul", "fsl,imx6ul";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_gpio_dvfs: reg-gpio-dvfs {
+		compatible = "regulator-gpio";
+		regulator-min-microvolt = <1300000>;
+		regulator-max-microvolt = <1400000>;
+		regulator-name = "gpio_dvfs";
+		regulator-type = "voltage";
+		gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		states = <1300000 0x1 1400000 0x0>;
+	};
+
+	rmii_ref_clk: rmii-ref-clk-grp {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+		clock-output-names = "rmii-ref";
+	};
+};
+
+&cpu0 {
+	dc-supply = <&reg_gpio_dvfs>;
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <786432000>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>, <&pinctrl_enet1_gpio>, <&pinctrl_enet1_mdio>;
+	phy-mode = "rmii";
+	phy-reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			micrel,rmii-reference-clock-select-25-mhz = <1>;
+			micrel,led-mode = <1>;
+			clocks = <&rmii_ref_clk>;
+			clock-names = "rmii-ref";
+			reg = <1>;
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x1b0b0	/* BT Enable */
+			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x03029	/* WLAN Enable */
+		>;
+	};
+
+	pinctrl_enet1_gpio: enet1-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0 /* fec1 reset */
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+		>;
+	};
+
+	pinctrl_enet1_mdio: enet1-mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x11088
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x11088
+			MX6UL_PAD_JTAG_TMS__SAI2_MCLK		0x17088
+		>;
+	};
+
+	pinctrl_tsc: tscgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0xb0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART2_CTS_B__UART2_DCE_CTS	0x1b0b1
+			MX6UL_PAD_UART2_RTS_B__UART2_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170b9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170b9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170b9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x170f9
+		>;
+	};
+};
+
+&pxp {
+	status = "okay";
+};
+
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
+			  <&clks IMX6UL_CLK_SAI2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <0>, <12288000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&tsc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_tsc>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	measure-delay-time = <0xffff>;
+	pre-charge-time = <0xfff>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};

-- 
2.47.0.2.g7caf9f4c55.dirty

[PATCH 3/3] ARM: dts: imx6ul: Add Variscite Concerto board support

[Antonin Godard]

This patch adds support for the Variscite Concerto Carrier Board.

This Carrier-Board has the following:
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch
  display (not configured)
- USB Host + USB OTG Connector
- 10/100 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- S-ATA
- On-board DMIC

Product Page: https://www.variscite.com/product/single-board-computers/concerto-board

This file is based on the one provided by Variscite on their own kernel,
but adapted for mainline.

Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
---
 arch/arm/boot/dts/nxp/imx/Makefile                 |   1 +
 .../boot/dts/nxp/imx/imx6ul-var-som-concerto.dts   | 331 +++++++++++++++++++++
 2 files changed, 332 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index 39a153536d2a2b8f75b5fbe4332660f89442064a..94c9bc94cc8e2daa1fb3b5686b0b58db1f6678b6 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -329,6 +329,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-tx6ul-0010.dtb \
 	imx6ul-tx6ul-0011.dtb \
 	imx6ul-tx6ul-mainboard.dtb \
+	imx6ul-var-som-concerto.dtb \
 	imx6ull-14x14-evk.dtb \
 	imx6ull-colibri-aster.dtb \
 	imx6ull-colibri-emmc-aster.dtb \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts
new file mode 100644
index 0000000000000000000000000000000000000000..4289641d94c5a72ba985f339652039dbf13da40c
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts
@@ -0,0 +1,331 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Support for Variscite MX6 Concerto Carrier board with the VAR-SOM-MX6UL
+ * Variscite SoM mounted on it
+ *
+ * Copyright 2019 Variscite Ltd.
+ * Copyright 2025 Bootlin
+ */
+
+#include "imx6ul-var-som.dtsi"
+
+/ {
+	model = "Variscite VAR-SOM-MX6UL Concerto Board";
+	compatible = "variscite,mx6concerto", "variscite,var-som-imx6ul", "fsl,imx6ul";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 20000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_key_back>, <&pinctrl_gpio_key_wakeup>;
+
+		key-back {
+			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BACK>;
+		};
+
+		key-wakeup {
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		gpled2 {
+			gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&fec1 {
+	status = "disabled";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>, <&pinctrl_enet2_gpio>, <&pinctrl_enet2_mdio>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	phy-reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <100>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@3 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			micrel,rmii-reference-clock-select-25-mhz = <1>;
+			micrel,led-mode = <0>;
+			clocks = <&rmii_ref_clk>;
+			clock-names = "rmii-ref";
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* DS1337 RTC module */
+	rtc@68 {
+		/*
+		 * To actually use this interrupt
+		 * connect pins J14.8 & J14.10 on the Concerto-Board.
+		 */
+		compatible = "dallas,ds1337";
+		reg = <0x68>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
+&iomuxc {
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b031
+		>;
+	};
+
+	pinctrl_enet2_mdio: enet2-mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+		>;
+	};
+
+	pinctrl_enet2_gpio: enet2-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0 /* fec2 reset */
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_gpio_key_back: gpio-key-backgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CE1_B__GPIO4_IO14	0x17059 /* Back */
+		>;
+	};
+
+	pinctrl_gpio_leds: gpio-ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0x1b0b0	/* GPLED2 */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO05__PWM4_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0x1b0b0 /* RTC alarm IRQ */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA00__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_CSI_DATA01__UART5_DCE_RX	0x1b0b1
+			MX6UL_PAD_GPIO1_IO09__UART5_DCE_CTS	0x1b0b1
+			MX6UL_PAD_GPIO1_IO08__UART5_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1_id: usbotg1idgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__ANATOP_OTG1_ID	0x17059
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__WDOG1_WDOG_B	0x78b0
+		>;
+	};
+
+	pinctrl_ft5x06_ts_gpio: ft5x06-ts-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x80000000
+		>;
+	};
+
+	pinctrl_gpio_key_wakeup: gpio-keys-wakeupgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x17059 /* Wakeup */
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x17059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_usdhc1_gpio: usdhc1-gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00	0x1b0b1 /* CD */
+		>;
+	};
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "disabled";
+};
+
+&snvs_rtc {
+	status = "disabled";
+};
+
+&tsc {
+	/*
+	 * Conflics with wdog1 ext-reset-output & SD CD pins,
+	 * so we keep it disabled by default.
+	 */
+	status = "disabled";
+};
+
+/* Console UART */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* ttymxc4 UART */
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1_id>;
+	dr_mode = "otg";
+	disable-over-current;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	/*
+	 * To actually use ext-reset-output
+	 * connect pins J17.3 & J17.8 on the Concerto-Board
+	 */
+	fsl,ext-reset-output;
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};

-- 
2.47.0.2.g7caf9f4c55.dirty

Re: [PATCH 3/3] ARM: dts: imx6ul: Add Variscite Concerto board support

[Krzysztof Kozlowski]

On 21/01/2025 10:33, Antonin Godard wrote:
> This patch adds support for the Variscite Concerto Carrier Board.

Please do not use "This commit/patch/change", but imperative mood. See
longer explanation here:
https://elixir.bootlin.com/linux/v5.17.1/source/Documentation/process/submitting-patches.rst#L95
> 
> This Carrier-Board has the following:
> - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch
>   display (not configured)
> - USB Host + USB OTG Connector
> - 10/100 Mbps Ethernet
> - miniPCI-Express slot
> - SD Card connector
> - Audio Headphone/Line In jack connectors
> - S-ATA
> - On-board DMIC
> 
> Product Page: https://www.variscite.com/product/single-board-computers/concerto-board
> 
> This file is based on the one provided by Variscite on their own kernel,
> but adapted for mainline.
> 
> Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
> ---
>  arch/arm/boot/dts/nxp/imx/Makefile                 |   1 +
>  .../boot/dts/nxp/imx/imx6ul-var-som-concerto.dts   | 331 +++++++++++++++++++++
>  2 files changed, 332 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
> index 39a153536d2a2b8f75b5fbe4332660f89442064a..94c9bc94cc8e2daa1fb3b5686b0b58db1f6678b6 100644
> --- a/arch/arm/boot/dts/nxp/imx/Makefile
> +++ b/arch/arm/boot/dts/nxp/imx/Makefile
> @@ -329,6 +329,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
>  	imx6ul-tx6ul-0010.dtb \
>  	imx6ul-tx6ul-0011.dtb \
>  	imx6ul-tx6ul-mainboard.dtb \
> +	imx6ul-var-som-concerto.dtb \
>  	imx6ull-14x14-evk.dtb \
>  	imx6ull-colibri-aster.dtb \
>  	imx6ull-colibri-emmc-aster.dtb \
> diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts
> new file mode 100644
> index 0000000000000000000000000000000000000000..4289641d94c5a72ba985f339652039dbf13da40c
> --- /dev/null
> +++ b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts
> @@ -0,0 +1,331 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Support for Variscite MX6 Concerto Carrier board with the VAR-SOM-MX6UL
> + * Variscite SoM mounted on it
> + *
> + * Copyright 2019 Variscite Ltd.
> + * Copyright 2025 Bootlin
> + */
> +
> +#include "imx6ul-var-som.dtsi"
> +
> +/ {
> +	model = "Variscite VAR-SOM-MX6UL Concerto Board";
> +	compatible = "variscite,mx6concerto", "variscite,var-som-imx6ul", "fsl,imx6ul";
> +
> +	backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm4 0 20000 0>;
> +		brightness-levels = <0 4 8 16 32 64 128 255>;
> +		default-brightness-level = <6>;
> +		status = "okay";

Which file disables it?

> +	};
> +
> +	chosen {
> +		stdout-path = &uart1;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_key_back>, <&pinctrl_gpio_key_wakeup>;
> +
> +		key-back {
> +			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_BACK>;
> +		};
> +
> +		key-wakeup {
> +			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_WAKEUP>;
> +			wakeup-source;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> +		gpled2 {

led-0
led-1
led-2

Are there other leds here?


> +			gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";

Missing function and color

> +		};
> +	};
> +};
> +
> +&can1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan1>;
> +	status = "okay";
> +};
> +
> +&fec1 {
> +	status = "disabled";
> +};
> +
> +&fec2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet2>, <&pinctrl_enet2_gpio>, <&pinctrl_enet2_mdio>;
> +	phy-mode = "rmii";
> +	phy-handle = <&ethphy1>;
> +	phy-reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
> +	phy-reset-duration = <100>;
> +	status = "okay";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy1: ethernet-phy@3 {
> +			compatible = "ethernet-phy-ieee802.3-c22";
> +			micrel,rmii-reference-clock-select-25-mhz = <1>;
> +			micrel,led-mode = <0>;
> +			clocks = <&rmii_ref_clk>;
> +			clock-names = "rmii-ref";
> +			reg = <3>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	status = "okay";
> +
> +	/* DS1337 RTC module */

Drop comment, obvious. This cannot be anything else, because node name
and compatible told that.

> +	rtc@68 {
> +		/*
> +		 * To actually use this interrupt
> +		 * connect pins J14.8 & J14.10 on the Concerto-Board.
> +		 */
> +		compatible = "dallas,ds1337";
> +		reg = <0x68>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_rtc>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
> +	};
> +};


Best regards,
Krzysztof

Re: [PATCH 3/3] ARM: dts: imx6ul: Add Variscite Concerto board support

[Antonin Godard]

Hi Krzysztof,

On Tue Jan 21, 2025 at 5:03 PM CET, Krzysztof Kozlowski wrote:
> On 21/01/2025 10:33, Antonin Godard wrote:
>> This patch adds support for the Variscite Concerto Carrier Board.
>
> Please do not use "This commit/patch/change", but imperative mood. See
> longer explanation here:
> https://elixir.bootlin.com/linux/v5.17.1/source/Documentation/process/submitting-patches.rst#L95

Will do in v2.

>>
>> This Carrier-Board has the following:
>> - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch
>>   display (not configured)
>> - USB Host + USB OTG Connector
>> - 10/100 Mbps Ethernet
>> - miniPCI-Express slot
>> - SD Card connector
>> - Audio Headphone/Line In jack connectors
>> - S-ATA
>> - On-board DMIC
>> 
>> Product Page: https://www.variscite.com/product/single-board-computers/concerto-board
>> 
>> This file is based on the one provided by Variscite on their own kernel,
>> but adapted for mainline.
>> 
>> Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
>> ---
>>  arch/arm/boot/dts/nxp/imx/Makefile                 |   1 +
>>  .../boot/dts/nxp/imx/imx6ul-var-som-concerto.dts   | 331 +++++++++++++++++++++
>>  2 files changed, 332 insertions(+)
>> 
>> diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
>> index 39a153536d2a2b8f75b5fbe4332660f89442064a..94c9bc94cc8e2daa1fb3b5686b0b58db1f6678b6 100644
>> --- a/arch/arm/boot/dts/nxp/imx/Makefile
>> +++ b/arch/arm/boot/dts/nxp/imx/Makefile
>> @@ -329,6 +329,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
>>  	imx6ul-tx6ul-0010.dtb \
>>  	imx6ul-tx6ul-0011.dtb \
>>  	imx6ul-tx6ul-mainboard.dtb \
>> +	imx6ul-var-som-concerto.dtb \
>>  	imx6ull-14x14-evk.dtb \
>>  	imx6ull-colibri-aster.dtb \
>>  	imx6ull-colibri-emmc-aster.dtb \
>> diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts
>> new file mode 100644
>> index 0000000000000000000000000000000000000000..4289641d94c5a72ba985f339652039dbf13da40c
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/nxp/imx/imx6ul-var-som-concerto.dts
>> @@ -0,0 +1,331 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Support for Variscite MX6 Concerto Carrier board with the VAR-SOM-MX6UL
>> + * Variscite SoM mounted on it
>> + *
>> + * Copyright 2019 Variscite Ltd.
>> + * Copyright 2025 Bootlin
>> + */
>> +
>> +#include "imx6ul-var-som.dtsi"
>> +
>> +/ {
>> +	model = "Variscite VAR-SOM-MX6UL Concerto Board";
>> +	compatible = "variscite,mx6concerto", "variscite,var-som-imx6ul", "fsl,imx6ul";
>> +
>> +	backlight {
>> +		compatible = "pwm-backlight";
>> +		pwms = <&pwm4 0 20000 0>;
>> +		brightness-levels = <0 4 8 16 32 64 128 255>;
>> +		default-brightness-level = <6>;
>> +		status = "okay";
>
> Which file disables it?

This is a mistake, I forgot to remove this when removing the parts I couldn't
test. Will remove this node in v2.

>> +	};
>> +
>> +	chosen {
>> +		stdout-path = &uart1;
>> +	};
>> +
>> +	gpio-keys {
>> +		compatible = "gpio-keys";
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_gpio_key_back>, <&pinctrl_gpio_key_wakeup>;
>> +
>> +		key-back {
>> +			gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
>> +			linux,code = <KEY_BACK>;
>> +		};
>> +
>> +		key-wakeup {
>> +			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
>> +			linux,code = <KEY_WAKEUP>;
>> +			wakeup-source;
>> +		};
>> +	};
>> +
>> +	leds {
>> +		compatible = "gpio-leds";
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_gpio_leds>;
>> +
>> +		gpled2 {
>
> led-0
> led-1
> led-2

Will rename this node to led-0, and set the label to "gpled2" (this is how it's
named on the schematic/datasheet).

> Are there other leds here?

Nothing else is obvious to me on the schematic. There is no gpled0 or gpled1.

>> +			gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
>> +			linux,default-trigger = "heartbeat";
>
> Missing function and color

Will set the function to STATUS, color green. This is a general purpose led that
can be used for debugging purposes or as a status indicator, I think.

>> +		};
>> +	};
>> +};
>> +
>> +&can1 {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_flexcan1>;
>> +	status = "okay";
>> +};
>> +
>> +&fec1 {
>> +	status = "disabled";
>> +};
>> +
>> +&fec2 {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_enet2>, <&pinctrl_enet2_gpio>, <&pinctrl_enet2_mdio>;
>> +	phy-mode = "rmii";
>> +	phy-handle = <&ethphy1>;
>> +	phy-reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
>> +	phy-reset-duration = <100>;
>> +	status = "okay";
>> +
>> +	mdio {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		ethphy1: ethernet-phy@3 {
>> +			compatible = "ethernet-phy-ieee802.3-c22";
>> +			micrel,rmii-reference-clock-select-25-mhz = <1>;
>> +			micrel,led-mode = <0>;
>> +			clocks = <&rmii_ref_clk>;
>> +			clock-names = "rmii-ref";
>> +			reg = <3>;
>> +		};
>> +	};
>> +};
>> +
>> +&i2c1 {
>> +	clock-frequency = <100000>;
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_i2c1>;
>> +	status = "okay";
>> +
>> +	/* DS1337 RTC module */
>
> Drop comment, obvious. This cannot be anything else, because node name
> and compatible told that.

Will do in v2.

>> +	rtc@68 {
>> +		/*
>> +		 * To actually use this interrupt
>> +		 * connect pins J14.8 & J14.10 on the Concerto-Board.
>> +		 */
>> +		compatible = "dallas,ds1337";
>> +		reg = <0x68>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&pinctrl_rtc>;
>> +		interrupt-parent = <&gpio1>;
>> +		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
>> +	};
>> +};
>
>
> Best regards,
> Krzysztof

Thanks for the review,
Antonin

-- 
Antonin Godard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Re: [PATCH 0/3] Add Variscite i.MX6UL SoM and Concerto board support

[Rob Herring (Arm)]

On Tue, 21 Jan 2025 10:33:26 +0100, Antonin Godard wrote:
> This patch series adds support for the i.MX6UL Variscite SoM
> (VAR-SOM-6UL) and the Variscite Concerto Carrier Board.
> 
> I tested this with a VAR-SOM-6UL_G2_700C_512R_8N_IT_REV1.3A (one variant
> of this SoM), meaning I couldn't test all of the possible options of the
> SoM - so this device tree includes partial support for it.
> 
> These are based on the 5.15 Variscite kernel fork but adapted for
> mainline.
> 
> Signed-off-by: Antonin Godard <antonin.godard@bootlin.com>
> ---
> Antonin Godard (3):
>       dt-bindings: arm: fsl: Add VAR-SOM-MX6UL SoM and Concerto board
>       ARM: dts: imx6ul: Add Variscite VAR-SOM-MX6UL SoM support
>       ARM: dts: imx6ul: Add Variscite Concerto board support
> 
>  Documentation/devicetree/bindings/arm/fsl.yaml     |   6 +
>  arch/arm/boot/dts/nxp/imx/Makefile                 |   1 +
>  .../boot/dts/nxp/imx/imx6ul-var-som-concerto.dts   | 331 +++++++++++++++++++++
>  arch/arm/boot/dts/nxp/imx/imx6ul-var-som.dtsi      | 232 +++++++++++++++
>  4 files changed, 570 insertions(+)
> ---
> base-commit: ffd294d346d185b70e28b1a28abe367bbfe53c04
> change-id: 20250120-varsom6ul-concerto-dts-a08be2a6219b
> 
> Best regards,
> --
> Antonin Godard <antonin.godard@bootlin.com>
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y for arch/arm/boot/dts/nxp/' for 20250121-varsom6ul-concerto-dts-v1-0-eb349acf0ac6@bootlin.com:

arch/arm/boot/dts/nxp/imx/imx6dl-b125v2.dtb: clock-controller@20c4000: clocks: [[23]] is too short
	from schema $id: http://devicetree.org/schemas/clock/imx6q-clock.yaml#