Re: initrd-xxx.img create dracut not correct

[yeyouqun <yeyouqun1981-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>]

于 2013-3-12 16:37, Harald Hoyer 写道:
> Am 12.03.2013 02:14, schrieb yeyouqun:
>> 于 2013-3-11 17:31, Harald Hoyer 写道:
>>> Am 10.03.2013 10:29, schrieb yeyouqun:
>>>> 于 2013-3-8 15:02, Harald Hoyer 写道:
>>>>> Am 08.03.2013 05:11, schrieb yeyouqun:
>>>>>> Recently I upgraded linux kernel to 3.6.10 and upgrade dracut version to 024,
>>>>>> system starts up OK on 3.6.10. But when I upgraded kernel from 3.6.10 to
>>>>>> 3.8.2,
>>>>>> dracut failed to start up the system. Message when start up reads:
>>>>>>
>>>>>> ......
>>>>>>       dracut: dracut-dracut-024-
>>>>>>        rpcbind: cannot create socket for udp6
>>>>>>        rpcbind: cannot create socket for tcp6
>>>>>>        mount: unknoun filesys
>>>>>>        udev: starting version 147
>>>>>>        systend-udevd (139): /proc/139/oom_adj is deprecated, please use
>>>>>>        /proc/139/oom_score_adj instead.
>>>>>>        dracut Warning: Could not boot.
>>>>>>        dracut Warning: Could not boot.
>>>>>>        Dropping to debug shell.
>>>>>>        /bin/sh: can't access tty; job control turned off
>>>>>> ......
>>>>>>
>>>>>> But when I unpack the initrd-3.8.2.img, the /lib/modules directory shows as
>>>>>> below:
>>>>>>
>>>>>> modules ---- 3.8.2
>>>>>>             |
>>>>>>             |__ 3.6.10
>>>>>>
>>>>>> all the kernel modules reside in "3.6.10" directory and other files, such as
>>>>>> "modules.dep" and etc. reside in 3.8.2, I think this is the reason why system
>>>>>> can't start up.
>>>>>>
>>>>>> I upgraded kernel by the steps as(in kernel source tree of 3.8.2):
>>>>>>
>>>>>>        make
>>>>>>        make modules_install
>>>>>>        make install
>>>>>>
>>>>>> Any one can tell how to fix this behavior of dracut?
>>>>> What's the output of:
>>>> output is two big, I appende it.
>>>>> # dracut --debug test.img 3.8.2
>>> /usr/lib/dracut/dracut-functions.sh@1377(dracut_kernel_post): xargs -r modprobe
>>> -a -d / --ignore-install --show-depends --set-version 3.8.2
>>> /usr/lib/dracut/dracut-functions.sh@1382(dracut_kernel_post): [[ insmod =
>>> insmod ]]
>>> /usr/lib/dracut/dracut-functions.sh@1383(dracut_kernel_post): echo
>>> ///lib/modules/3.6.10/kernel/arch/x86/crypto/crc32c-intel.ko
>>>
>>>
>>> This looks fishy...
>>>
>>>
>>> What is the output of:
>>>
>>> # modprobe -a --ignore-install --show-depends --set-version 3.8.2 xor
>>>
>> [root@localhost mnt]# modprobe -a --ignore-install --show-depends --set-version
>> 3.8.2 xor
>> insmod /lib/modules/3.8.2/kernel/crypto/xor.ko
> and what is the output of:
>
> # modprobe -a -d / --ignore-install --show-depends --set-version 3.8.2 xor
[root@localhost mnt]# modprobe -a -d / --ignore-install --show-depends 
--set-version 3.8.2 xor
insmod ///lib/modules/3.6.10/kernel/crypto/xor.ko

BTW:I tried to upgrade dracut to 025 and problem seems gone!