From: Ben Widawsky <ben@bwidawsk.net>
To: intel-gfx@lists.freedesktop.org
Cc: Ben Widawsky <ben@bwidawsk.net>
Subject: [PATCH 1/4 v5] drm/i915: timeout parameter for seqno wait
Date: Thu, 24 May 2012 15:03:08 -0700 [thread overview]
Message-ID: <1337896991-4795-1-git-send-email-ben@bwidawsk.net> (raw)
Insert a wait parameter in the code so we can possibly timeout on a
seqno wait if need be. The code should be functionally the same as
before because all the callers will continue to retry if an arbitrary
timeout elapses.
We'd like to have nanosecond granularity, but the only way to do this is
with hrtimer, and that doesn't fit well with the needs of this code.
v2: Fix rebase error (Chris)
Return proper time even in wedged + signal case (Chris + Ben)
Use timespec constructs (Ben)
Didn't take Daniel's advice regarding the Frankenstein-ness of the
function. I did try his advice, but in the end I liked the way the
original code looked, better.
v3: Make wakeups far less frequent for infinite waits (Chris)
v4: Remove dummy_wait variable (Daniel)
Use raw monotonic time instead of jiffies (made the code a bit cleaner) (Ben)
Added a couple of warnings (Ben)
v5: Remove warnings (Daniel)
Use more accurate time diff for default case (Daniel)
Bikeshed for setting the return timespec in timeout case (Daniel)
s/jiffies/time in one of the comments
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
---
drivers/gpu/drm/i915/i915_gem.c | 70 ++++++++++++++++++++++++++++++++-------
1 file changed, 58 insertions(+), 12 deletions(-)
diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c
index 44a5f24..d25464a 100644
--- a/drivers/gpu/drm/i915/i915_gem.c
+++ b/drivers/gpu/drm/i915/i915_gem.c
@@ -1868,34 +1868,82 @@ i915_gem_check_olr(struct intel_ring_buffer *ring, u32 seqno)
return ret;
}
+/**
+ * __wait_seqno - wait until execution of seqno has finished
+ * @ring: the ring expected to report seqno
+ * @seqno: duh!
+ * @interruptible: do an interruptible wait (normally yes)
+ * @timeout: in - how long to wait (NULL forever); out - how much time remaining
+ *
+ * Returns 0 if the seqno was found within the alloted time. Else returns the
+ * errno with remaining time filled in timeout argument.
+ */
static int __wait_seqno(struct intel_ring_buffer *ring, u32 seqno,
- bool interruptible)
+ bool interruptible, struct timespec *timeout)
{
drm_i915_private_t *dev_priv = ring->dev->dev_private;
- int ret = 0;
+ struct timespec before, now, wait_time={1,0};
+ unsigned long timeout_jiffies;
+ long end;
+ bool wait_forever = true;
if (i915_seqno_passed(ring->get_seqno(ring), seqno))
return 0;
trace_i915_gem_request_wait_begin(ring, seqno);
+
+ if (timeout != NULL) {
+ wait_time = *timeout;
+ wait_forever = false;
+ }
+
+ timeout_jiffies = timespec_to_jiffies(&wait_time);
+
if (WARN_ON(!ring->irq_get(ring)))
return -ENODEV;
+ /* Record current time in case interrupted by signal, or wedged * */
+ getrawmonotonic(&before);
+
#define EXIT_COND \
(i915_seqno_passed(ring->get_seqno(ring), seqno) || \
atomic_read(&dev_priv->mm.wedged))
+ do {
+ if (interruptible)
+ end = wait_event_interruptible_timeout(ring->irq_queue,
+ EXIT_COND,
+ timeout_jiffies);
+ else
+ end = wait_event_timeout(ring->irq_queue, EXIT_COND,
+ timeout_jiffies);
- if (interruptible)
- ret = wait_event_interruptible(ring->irq_queue,
- EXIT_COND);
- else
- wait_event(ring->irq_queue, EXIT_COND);
+ if (atomic_read(&dev_priv->mm.wedged))
+ end = -EAGAIN;
+ } while (end == 0 && wait_forever);
+
+ getrawmonotonic(&now);
ring->irq_put(ring);
trace_i915_gem_request_wait_end(ring, seqno);
#undef EXIT_COND
- return ret;
+ if (timeout) {
+ struct timespec sleep_time = timespec_sub(now, before);
+ *timeout = timespec_sub(*timeout, sleep_time);
+ }
+
+ switch (end) {
+ case -EAGAIN: /* Wedged */
+ case -ERESTARTSYS: /* Signal */
+ return (int)end;
+ case 0: /* Timeout */
+ if (timeout)
+ set_normalized_timespec(timeout, 0, 0);
+ return -ETIME;
+ default: /* Completed */
+ WARN_ON(end < 0); /* We're not aware of other errors */
+ return 0;
+ }
}
/**
@@ -1919,9 +1967,7 @@ i915_wait_request(struct intel_ring_buffer *ring,
if (ret)
return ret;
- ret = __wait_seqno(ring, seqno, dev_priv->mm.interruptible);
- if (atomic_read(&dev_priv->mm.wedged))
- ret = -EAGAIN;
+ ret = __wait_seqno(ring, seqno, dev_priv->mm.interruptible, NULL);
return ret;
}
@@ -2996,7 +3042,7 @@ i915_gem_ring_throttle(struct drm_device *dev, struct drm_file *file)
if (seqno == 0)
return 0;
- ret = __wait_seqno(ring, seqno, true);
+ ret = __wait_seqno(ring, seqno, true, NULL);
if (ret == 0)
queue_delayed_work(dev_priv->wq, &dev_priv->mm.retire_work, 0);
--
1.7.10.2
next reply other threads:[~2012-05-24 22:05 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-05-24 22:03 Ben Widawsky [this message]
2012-05-24 22:03 ` [PATCH 2/4 v3] [RESEND] drm/i915: improve i915_wait_request_begin trace Ben Widawsky
2012-05-24 22:03 ` [PATCH 3/4 v7] drm/i915: wait render timeout ioctl Ben Widawsky
2012-05-25 3:18 ` Ben Widawsky
2012-06-05 21:09 ` Chris Wilson
2012-05-24 22:03 ` [PATCH 4/4] [RESEND] drm/i915: s/i915_wait_request/i915_wait_seqno/g Ben Widawsky
2012-05-25 12:20 ` Daniel Vetter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1337896991-4795-1-git-send-email-ben@bwidawsk.net \
--to=ben@bwidawsk.net \
--cc=intel-gfx@lists.freedesktop.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox