From: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
To: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Subject: Re: [PATCH 03/10] drm/i915: add pipe_config->timings_set
Date: Fri, 22 Feb 2013 15:51:15 +0200 [thread overview]
Message-ID: <20130222135115.GN4469@intel.com> (raw)
In-Reply-To: <1361491014-13888-4-git-send-email-daniel.vetter@ffwll.ch>
On Fri, Feb 22, 2013 at 12:56:47AM +0100, Daniel Vetter wrote:
> Only used by the lvds encoder. Note that we shouldn't do the same
> simple conversion with the FORCE_6BPC flag, since that's much better
> handled by moving all the pipe_bpc computation around.
>
> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
> ---
> drivers/gpu/drm/i915/intel_display.c | 12 +++++++++++-
> drivers/gpu/drm/i915/intel_drv.h | 10 ++++++----
> drivers/gpu/drm/i915/intel_lvds.c | 19 +++++++++----------
> 3 files changed, 26 insertions(+), 15 deletions(-)
>
<snip>
> @@ -359,6 +357,7 @@ static bool intel_lvds_mode_fixup(struct drm_encoder *encoder,
> I915_WRITE(BCLRPAT(pipe), 0);
>
> drm_mode_set_crtcinfo(adjusted_mode, 0);
> + pipe_config->timings_set = true;
This changes the behaviour a bit. Previously the flag was only set from
the centering funcs, but now it's set always. Is that intentional?
>
> switch (intel_connector->panel.fitting_mode) {
> case DRM_MODE_SCALE_CENTER:
> @@ -661,7 +660,6 @@ static int intel_lvds_set_property(struct drm_connector *connector,
> }
>
> static const struct drm_encoder_helper_funcs intel_lvds_helper_funcs = {
> - .mode_fixup = intel_lvds_mode_fixup,
> .mode_set = intel_lvds_mode_set,
> };
>
> @@ -1102,6 +1100,7 @@ bool intel_lvds_init(struct drm_device *dev)
> intel_encoder->enable = intel_enable_lvds;
> intel_encoder->pre_enable = intel_pre_enable_lvds;
> intel_encoder->pre_pll_enable = intel_pre_pll_enable_lvds;
> + intel_encoder->compute_config = intel_lvds_compute_config;
> intel_encoder->disable = intel_disable_lvds;
> intel_encoder->get_hw_state = intel_lvds_get_hw_state;
> intel_connector->get_hw_state = intel_connector_get_hw_state;
> --
> 1.7.11.4
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Ville Syrjälä
Intel OTC
next prev parent reply other threads:[~2013-02-22 13:51 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-02-21 23:56 [PATCH 00/10] basic infrastructure for pipe_config Daniel Vetter
2013-02-21 23:56 ` [PATCH 01/10] drm/i915: introduce struct intel_crtc_config Daniel Vetter
2013-02-22 10:23 ` Ville Syrjälä
2013-02-22 11:05 ` [PATCH] " Daniel Vetter
2013-02-26 17:09 ` Paulo Zanoni
2013-02-21 23:56 ` [PATCH 02/10] drm/i915: compute pipe_config earlier Daniel Vetter
2013-02-26 17:11 ` Paulo Zanoni
2013-02-21 23:56 ` [PATCH 03/10] drm/i915: add pipe_config->timings_set Daniel Vetter
2013-02-22 13:51 ` Ville Syrjälä [this message]
2013-03-03 18:01 ` Daniel Vetter
2013-03-04 14:18 ` Ville Syrjälä
2013-02-26 17:23 ` Paulo Zanoni
2013-03-03 17:58 ` Daniel Vetter
2013-02-21 23:56 ` [PATCH 04/10] drm/i915: add pipe_config->pixel_multiplier Daniel Vetter
2013-02-26 17:27 ` Paulo Zanoni
2013-03-03 18:05 ` Daniel Vetter
2013-02-21 23:56 ` [PATCH 05/10] drm/i915: drop helper vtable for sdvo encoder Daniel Vetter
2013-02-21 23:56 ` [PATCH 06/10] drm/i915: add pipe_config->has_pch_encoder Daniel Vetter
2013-02-26 17:39 ` Paulo Zanoni
2013-03-03 18:13 ` Daniel Vetter
2013-03-03 18:16 ` [PATCH] " Daniel Vetter
2013-03-04 22:24 ` Daniel Vetter
2013-02-21 23:56 ` [PATCH 07/10] drm/i915: add pipe_config->limited_color_range Daniel Vetter
2013-02-26 17:46 ` Paulo Zanoni
2013-02-21 23:56 ` [PATCH 08/10] drm/i915: move pipe bpp computation to pipe_config Daniel Vetter
2013-03-26 21:12 ` Jesse Barnes
2013-03-26 21:32 ` Daniel Vetter
2013-02-21 23:56 ` [PATCH 09/10] drm/i915: clean up plane bpp confusion Daniel Vetter
2013-03-26 21:04 ` Jesse Barnes
2013-02-21 23:56 ` [PATCH 10/10] drm/i915: clean up pipe " Daniel Vetter
2013-03-26 21:06 ` Jesse Barnes
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130222135115.GN4469@intel.com \
--to=ville.syrjala@linux.intel.com \
--cc=daniel.vetter@ffwll.ch \
--cc=intel-gfx@lists.freedesktop.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox