From: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
To: Manasi Navare <manasi.d.navare@intel.com>
Cc: intel-gfx@lists.freedesktop.org,
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>,
Rodrigo Vivi <rodrigo.vivi@intel.com>
Subject: Re: [PATCH] drm/i915/dp: Give up link training clock recovery after 10 failed attempts
Date: Fri, 13 Jul 2018 16:17:03 -0700 [thread overview]
Message-ID: <20180713231703.GA28794@nc-new> (raw)
In-Reply-To: <20180713221832.GA7428@intel.com>
On Fri, Jul 13, 2018 at 03:18:32PM -0700, Manasi Navare wrote:
> On Fri, Jul 13, 2018 at 03:23:41PM -0700, Dhinakaran Pandiyan wrote:
> > On Fri, 2018-07-13 at 14:22 -0700, Rodrigo Vivi wrote:
> > > On Fri, Jul 13, 2018 at 10:32:15AM -0700, Nathan Ciobanu wrote:
> > > >
> > > > Limit the link training clock recovery loop to 10 failed attempts
> > > > at
> > > > LANEx_CR_DONE per DP 1.4 spec.
> > > Where exactly in the spec?
>
> I see that this is specified in 3.5.1.2.2 Clock Recovery Sequence section
> in DP 1.4 spec. Might be a good idea to mention this expliitly in the commit message.
Right, I'll do that.
>
> > >
> > > >
> > > > Some USB-C MST hubs cause us to get
> > > > stuck in this loop on hot-plugging indefinitely as
>
> This is likely to occur in case of USB Type C cases where only fewer lanes
> might be connected whereas the max lane count returned is still 4.
> If this is the case, explicitly mentioning this is also a good idea.
I'm pretty sure this device uses 4 lanes. I am getting voltage swing/pre-emphasis
values and status on all 4.
>
> Doesnt this get recovered at all after the fallback when it will eventually
> try with the lower lane count?
Yes it does recover after the 10 attempts.
>
> >
> > Also include the information (the vswing toggling part) about why it is
> > stuck in the loop.
> >
> > > > drm_dp_clock_recovery_ok() never returns true and none of the
> > > > other conditions occur.
> > > Although it seems really bad situation that we need to avoid...
> > >
> > > >
> > > >
> > > > Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
> > > > ---
> > > > drivers/gpu/drm/i915/intel_dp_link_training.c | 8 +++++++-
> > > > 1 file changed, 7 insertions(+), 1 deletion(-)
> > > >
> > > > diff --git a/drivers/gpu/drm/i915/intel_dp_link_training.c
> > > > b/drivers/gpu/drm/i915/intel_dp_link_training.c
> > > > index 4da6e33c7fa1..66c1a70343ba 100644
> > > > --- a/drivers/gpu/drm/i915/intel_dp_link_training.c
> > > > +++ b/drivers/gpu/drm/i915/intel_dp_link_training.c
> > > > @@ -129,7 +129,7 @@ static bool
> > > > intel_dp_link_max_vswing_reached(struct intel_dp *intel_dp)
> > > > intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp)
> > > > {
> > > > uint8_t voltage;
> > > > - int voltage_tries, max_vswing_tries;
> > > > + int voltage_tries, max_vswing_tries, cr_tries;
> > > > uint8_t link_config[2];
> > > > uint8_t link_bw, rate_select;
> > > >
> > > > @@ -172,6 +172,7 @@ static bool
> > > > intel_dp_link_max_vswing_reached(struct intel_dp *intel_dp)
> > > >
> > > > voltage_tries = 1;
> > > > max_vswing_tries = 0;
> > > > + cr_tries = 0;
> > > > for (;;) {
> > > > uint8_t link_status[DP_LINK_STATUS_SIZE];
> > > >
> > > > @@ -215,6 +216,11 @@ static bool
> > > > intel_dp_link_max_vswing_reached(struct intel_dp *intel_dp)
> > > > if (intel_dp_link_max_vswing_reached(intel_dp))
> > > > ++max_vswing_tries;
> > > >
> > > > + if (cr_tries == 9) {
> > > > + DRM_ERROR("Failed clock recovery 10 times,
> > > > giving up!\n");
> > > > + return false;
> > > > + }
> > > > + ++cr_tries;
> > > If I understood correctly this is a global thing for the for(;;)
> > > right?
> > >
> > > Shouldn't we make then like a:
> > >
> > > - for(;;)
> > > + for(cr_tries = 0; cr_tries < 10; cr_tries++)
> > > {
> > > }
>
> I think incrementing it at the end of the loop makes sense because we
> are checking for the 10 total read requests for lane_cr_done
> and adjust_request_lane.
> But if the max voltage swing is reached before that it should exit earlier.
>
> Manasi
>
> > >
> > > + DRM_ERROR("Failed clock recovery 10 times, giving up!\n");
> > > + return false;
> > > }
> > >
> > > Thanks,
> > > Rodrigo.
> > >
> > > >
> > > > }
> > > > }
> > > >
> > _______________________________________________
> > Intel-gfx mailing list
> > Intel-gfx@lists.freedesktop.org
> > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
>
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2018-07-13 23:24 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-13 17:32 [PATCH] drm/i915/dp: Give up link training clock recovery after 10 failed attempts Nathan Ciobanu
2018-07-13 18:25 ` ✓ Fi.CI.BAT: success for " Patchwork
2018-07-13 21:22 ` [PATCH] " Rodrigo Vivi
2018-07-13 22:23 ` Dhinakaran Pandiyan
2018-07-13 22:18 ` Manasi Navare
2018-07-13 23:17 ` Nathan Ciobanu [this message]
2018-07-13 22:49 ` Nathan Ciobanu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180713231703.GA28794@nc-new \
--to=nathan.d.ciobanu@linux.intel.com \
--cc=dhinakaran.pandiyan@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=manasi.d.navare@intel.com \
--cc=rodrigo.vivi@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox