From: Jani Nikula <jani.nikula@linux.intel.com>
To: Ville Syrjala <ville.syrjala@linux.intel.com>,
intel-gfx@lists.freedesktop.org
Subject: Re: [PATCH 07/10] drm/i915/crt: s/pipe_config/crtc_state/
Date: Fri, 08 Nov 2024 15:14:13 +0200 [thread overview]
Message-ID: <87ed3leul6.fsf@intel.com> (raw)
In-Reply-To: <20241107161123.16269-8-ville.syrjala@linux.intel.com>
On Thu, 07 Nov 2024, Ville Syrjala <ville.syrjala@linux.intel.com> wrote:
> From: Ville Syrjälä <ville.syrjala@linux.intel.com>
>
> Call the crtc state 'crtc_state' rather than 'pipe_config',
> as is the modern style.
>
> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
> ---
> drivers/gpu/drm/i915/display/intel_crt.c | 62 ++++++++++++------------
> 1 file changed, 31 insertions(+), 31 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/display/intel_crt.c b/drivers/gpu/drm/i915/display/intel_crt.c
> index 4784a858b4a2..0962a239288b 100644
> --- a/drivers/gpu/drm/i915/display/intel_crt.c
> +++ b/drivers/gpu/drm/i915/display/intel_crt.c
> @@ -150,27 +150,27 @@ static unsigned int intel_crt_get_flags(struct intel_encoder *encoder)
> }
>
> static void intel_crt_get_config(struct intel_encoder *encoder,
> - struct intel_crtc_state *pipe_config)
> + struct intel_crtc_state *crtc_state)
> {
> - pipe_config->output_types |= BIT(INTEL_OUTPUT_ANALOG);
> + crtc_state->output_types |= BIT(INTEL_OUTPUT_ANALOG);
>
> - pipe_config->hw.adjusted_mode.flags |= intel_crt_get_flags(encoder);
> + crtc_state->hw.adjusted_mode.flags |= intel_crt_get_flags(encoder);
>
> - pipe_config->hw.adjusted_mode.crtc_clock = pipe_config->port_clock;
> + crtc_state->hw.adjusted_mode.crtc_clock = crtc_state->port_clock;
> }
>
> static void hsw_crt_get_config(struct intel_encoder *encoder,
> - struct intel_crtc_state *pipe_config)
> + struct intel_crtc_state *crtc_state)
> {
> - lpt_pch_get_config(pipe_config);
> + lpt_pch_get_config(crtc_state);
>
> - hsw_ddi_get_config(encoder, pipe_config);
> + hsw_ddi_get_config(encoder, crtc_state);
>
> - pipe_config->hw.adjusted_mode.flags &= ~(DRM_MODE_FLAG_PHSYNC |
> - DRM_MODE_FLAG_NHSYNC |
> - DRM_MODE_FLAG_PVSYNC |
> - DRM_MODE_FLAG_NVSYNC);
> - pipe_config->hw.adjusted_mode.flags |= intel_crt_get_flags(encoder);
> + crtc_state->hw.adjusted_mode.flags &= ~(DRM_MODE_FLAG_PHSYNC |
> + DRM_MODE_FLAG_NHSYNC |
> + DRM_MODE_FLAG_PVSYNC |
> + DRM_MODE_FLAG_NVSYNC);
> + crtc_state->hw.adjusted_mode.flags |= intel_crt_get_flags(encoder);
> }
>
> /* Note: The caller is required to filter out dpms modes not supported by the
> @@ -408,48 +408,48 @@ intel_crt_mode_valid(struct drm_connector *connector,
> }
>
> static int intel_crt_compute_config(struct intel_encoder *encoder,
> - struct intel_crtc_state *pipe_config,
> + struct intel_crtc_state *crtc_state,
> struct drm_connector_state *conn_state)
> {
> struct drm_display_mode *adjusted_mode =
> - &pipe_config->hw.adjusted_mode;
> + &crtc_state->hw.adjusted_mode;
>
> if (adjusted_mode->flags & DRM_MODE_FLAG_DBLSCAN)
> return -EINVAL;
>
> - pipe_config->sink_format = INTEL_OUTPUT_FORMAT_RGB;
> - pipe_config->output_format = INTEL_OUTPUT_FORMAT_RGB;
> + crtc_state->sink_format = INTEL_OUTPUT_FORMAT_RGB;
> + crtc_state->output_format = INTEL_OUTPUT_FORMAT_RGB;
>
> return 0;
> }
>
> static int pch_crt_compute_config(struct intel_encoder *encoder,
> - struct intel_crtc_state *pipe_config,
> + struct intel_crtc_state *crtc_state,
> struct drm_connector_state *conn_state)
> {
> struct drm_display_mode *adjusted_mode =
> - &pipe_config->hw.adjusted_mode;
> + &crtc_state->hw.adjusted_mode;
>
> if (adjusted_mode->flags & DRM_MODE_FLAG_DBLSCAN)
> return -EINVAL;
>
> - pipe_config->has_pch_encoder = true;
> - if (!intel_fdi_compute_pipe_bpp(pipe_config))
> + crtc_state->has_pch_encoder = true;
> + if (!intel_fdi_compute_pipe_bpp(crtc_state))
> return -EINVAL;
>
> - pipe_config->output_format = INTEL_OUTPUT_FORMAT_RGB;
> + crtc_state->output_format = INTEL_OUTPUT_FORMAT_RGB;
>
> return 0;
> }
>
> static int hsw_crt_compute_config(struct intel_encoder *encoder,
> - struct intel_crtc_state *pipe_config,
> + struct intel_crtc_state *crtc_state,
> struct drm_connector_state *conn_state)
> {
> struct intel_display *display = to_intel_display(encoder);
> struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
> struct drm_display_mode *adjusted_mode =
> - &pipe_config->hw.adjusted_mode;
> + &crtc_state->hw.adjusted_mode;
>
> if (adjusted_mode->flags & DRM_MODE_FLAG_DBLSCAN)
> return -EINVAL;
> @@ -459,30 +459,30 @@ static int hsw_crt_compute_config(struct intel_encoder *encoder,
> adjusted_mode->crtc_hblank_start > 4096)
> return -EINVAL;
>
> - pipe_config->has_pch_encoder = true;
> - if (!intel_fdi_compute_pipe_bpp(pipe_config))
> + crtc_state->has_pch_encoder = true;
> + if (!intel_fdi_compute_pipe_bpp(crtc_state))
> return -EINVAL;
>
> - pipe_config->output_format = INTEL_OUTPUT_FORMAT_RGB;
> + crtc_state->output_format = INTEL_OUTPUT_FORMAT_RGB;
>
> /* LPT FDI RX only supports 8bpc. */
> if (HAS_PCH_LPT(dev_priv)) {
> /* TODO: Check crtc_state->max_link_bpp_x16 instead of bw_constrained */
> - if (pipe_config->bw_constrained && pipe_config->pipe_bpp < 24) {
> + if (crtc_state->bw_constrained && crtc_state->pipe_bpp < 24) {
> drm_dbg_kms(display->drm,
> "LPT only supports 24bpp\n");
> return -EINVAL;
> }
>
> - pipe_config->pipe_bpp = 24;
> + crtc_state->pipe_bpp = 24;
> }
>
> /* FDI must always be 2.7 GHz */
> - pipe_config->port_clock = 135000 * 2;
> + crtc_state->port_clock = 135000 * 2;
>
> - pipe_config->enhanced_framing = true;
> + crtc_state->enhanced_framing = true;
>
> - adjusted_mode->crtc_clock = lpt_iclkip(pipe_config);
> + adjusted_mode->crtc_clock = lpt_iclkip(crtc_state);
>
> return 0;
> }
--
Jani Nikula, Intel
next prev parent reply other threads:[~2024-11-08 13:14 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-11-07 16:11 [PATCH 00/10] drm/i915: Potential boot oops fix and some cleanups Ville Syrjala
2024-11-07 16:11 ` [PATCH 01/10] drm/i915: Grab intel_display from the encoder to avoid potential oopsies Ville Syrjala
2024-11-08 13:00 ` Jani Nikula
2024-11-11 22:03 ` Ville Syrjälä
2024-11-07 16:11 ` [PATCH 02/10] drm/i915/crt: Split long line Ville Syrjala
2024-11-08 13:01 ` Jani Nikula
2024-11-07 16:11 ` [PATCH 03/10] drm/i915/crt: Drop the unused ADPA_DPMS bit definitions Ville Syrjala
2024-11-08 13:02 ` Jani Nikula
2024-11-07 16:11 ` [PATCH 04/10] drm/i915/crt: Use REG_BIT() & co Ville Syrjala
2024-11-08 13:08 ` Jani Nikula
2024-11-07 16:11 ` [PATCH 05/10] drm/i915/crt: Clean up ADPA_HOTPLUG_BITS definitions Ville Syrjala
2024-11-08 13:12 ` Jani Nikula
2024-11-07 16:11 ` [PATCH 06/10] drm/i915/crt: Extract intel_crt_regs.h Ville Syrjala
2024-11-08 13:13 ` Jani Nikula
2024-11-07 16:11 ` [PATCH 07/10] drm/i915/crt: s/pipe_config/crtc_state/ Ville Syrjala
2024-11-08 13:14 ` Jani Nikula [this message]
2024-11-07 16:11 ` [PATCH 08/10] drm/i915/crt: Drop pointless drm_device variables Ville Syrjala
2024-11-08 13:15 ` Jani Nikula
2024-11-07 16:11 ` [PATCH 09/10] drm/i915/crt: Rename some variables Ville Syrjala
2024-11-08 13:16 ` Jani Nikula
2024-11-07 16:11 ` [PATCH 10/10] drm/i915/crt: Nuke unused crt->connector Ville Syrjala
2024-11-08 13:16 ` Jani Nikula
2024-11-08 4:56 ` ✗ Fi.CI.CHECKPATCH: warning for drm/i915: Potential boot oops fix and some cleanups (rev2) Patchwork
2024-11-08 4:56 ` ✗ Fi.CI.SPARSE: " Patchwork
2024-11-08 5:10 ` ✗ Fi.CI.BAT: failure " Patchwork
2024-11-08 17:08 ` ✗ Fi.CI.CHECKPATCH: warning for drm/i915: Potential boot oops fix and some cleanups (rev3) Patchwork
2024-11-08 17:08 ` ✗ Fi.CI.SPARSE: " Patchwork
2024-11-08 17:24 ` ✓ Fi.CI.BAT: success " Patchwork
2024-11-08 18:22 ` ✓ Fi.CI.IGT: " Patchwork
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87ed3leul6.fsf@intel.com \
--to=jani.nikula@linux.intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=ville.syrjala@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox