From: Jani Nikula <jani.nikula@intel.com>
To: Aditya Swarup <aditya.swarup@intel.com>, intel-gfx@lists.freedesktop.org
Subject: Re: [PATCH v9] drm/i915/icl: Set GCP_COLOR_INDICATION only for 10/12 bit deep color
Date: Tue, 07 May 2019 09:42:48 +0300 [thread overview]
Message-ID: <87h8a6n4t3.fsf@intel.com> (raw)
In-Reply-To: <20190429230811.9983-1-aditya.swarup@intel.com>
On Mon, 29 Apr 2019, Aditya Swarup <aditya.swarup@intel.com> wrote:
> From: Clinton Taylor <Clinton.A.Taylor@intel.com>
>
> v2: Fix commit msg to reflect why issue occurs(Jani)
> Set GCP_COLOR_INDICATION only when we set 10/12 bit deep color.
>
> Changing settings from 10/12 bit deep color to 8 bit(& vice versa)
> doesn't work correctly using xrandr max bpc property. When we
> connect a monitor which supports deep color, the highest deep color
> setting is selected; which sets GCP_COLOR_INDICATION. When we change
> the setting to 8 bit color, we still set GCP_COLOR_INDICATION which
> doesn't allow the switch back to 8 bit color.
>
> v3,4: Add comments & drop changes in intel_hdmi_compute_config(Ville)
> Since HSW+, GCP_COLOR_INDICATION is not required for 8bpc.
>
> Drop the changes in intel_hdmi_compute_config as desired_bpp
> is needed to change values for pipe_bpp based on bw_constrained flag.
>
> v5: Fix missing logical && in condition for setting GCP_COLOR_INDICATION.
>
> v6: Fix comment formatting (Ville)
>
> v7: Add reviewed by Ville
>
> v8: Set GCP_COLOR_INDICATION based on spec:
> For Gen 7.5 or later platforms, indicate color depth only for deep
> color modes. Bspec: 8135,7751,50524
>
> Pre DDI platforms, indicate color depth if deep color is supported
> by sink. Bspec: 7854
>
> Exception: CHERRYVIEW behaves like Pre DDI platforms.
> Bspec: 15975
>
> Check pipe_bpp is less than bpp * 3 in hdmi_deep_color_possible,
> to not set 12 bit deep color for every modeset. This fixes the issue
> where 12 bit color was selected even when user selected 10 bit.(Ville)
>
> v9: Maintain a consistent behavior for all platforms and support
> GCP_COLOR_INDICATION only when we are in deep color mode. Remove
> hdmi_sink_is_deep_color() - no longer needed as checking pipe_bpp > 24
> takes care of the deep color mode scenario.
>
> Separate patch for fixing switch from 12 bit to 10 bit deep color
> mode.
>
> Co-developed-by: Aditya Swarup <aditya.swarup@intel.com>
> Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
> Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
> Cc: Jani Nikula <jani.nikula@intel.com>
> Cc: Manasi Navare <manasi.d.navare@intel.com>
> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Ville, does this apply to this version of the patch?
BR,
Jani.
> ---
> drivers/gpu/drm/i915/intel_hdmi.c | 17 ++---------------
> 1 file changed, 2 insertions(+), 15 deletions(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_hdmi.c b/drivers/gpu/drm/i915/intel_hdmi.c
> index e1005d7b75fd..991eb362ef4f 100644
> --- a/drivers/gpu/drm/i915/intel_hdmi.c
> +++ b/drivers/gpu/drm/i915/intel_hdmi.c
> @@ -856,19 +856,6 @@ static void g4x_set_infoframes(struct intel_encoder *encoder,
> &crtc_state->infoframes.hdmi);
> }
>
> -static bool hdmi_sink_is_deep_color(const struct drm_connector_state *conn_state)
> -{
> - struct drm_connector *connector = conn_state->connector;
> -
> - /*
> - * HDMI cloning is only supported on g4x which doesn't
> - * support deep color or GCP infoframes anyway so no
> - * need to worry about multiple HDMI sinks here.
> - */
> -
> - return connector->display_info.bpc > 8;
> -}
> -
> /*
> * Determine if default_phase=1 can be indicated in the GCP infoframe.
> *
> @@ -973,8 +960,8 @@ static void intel_hdmi_compute_gcp_infoframe(struct intel_encoder *encoder,
> crtc_state->infoframes.enable |=
> intel_hdmi_infoframe_enable(HDMI_PACKET_TYPE_GENERAL_CONTROL);
>
> - /* Indicate color depth whenever the sink supports deep color */
> - if (hdmi_sink_is_deep_color(conn_state))
> + /* Indicate color indication for deep color mode */
> + if (crtc_state->pipe_bpp > 24)
> crtc_state->infoframes.gcp |= GCP_COLOR_INDICATION;
>
> /* Enable default_phase whenever the display mode is suitably aligned */
--
Jani Nikula, Intel Open Source Graphics Center
_______________________________________________
Intel-gfx mailing list
Intel-gfx@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
next prev parent reply other threads:[~2019-05-07 6:40 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-04-29 23:08 [PATCH v9] drm/i915/icl: Set GCP_COLOR_INDICATION only for 10/12 bit deep color Aditya Swarup
2019-04-30 8:21 ` ✓ Fi.CI.BAT: success for drm/i915/icl: Set GCP_COLOR_INDICATION only for 10/12 bit deep color (rev8) Patchwork
2019-04-30 13:46 ` ✗ Fi.CI.IGT: failure " Patchwork
2019-05-03 23:04 ` Aditya Swarup
2019-05-04 5:55 ` Saarinen, Jani
2019-05-06 6:59 ` Tomi Sarvela
2019-05-03 20:44 ` ✓ Fi.CI.BAT: success for drm/i915/icl: Set GCP_COLOR_INDICATION only for 10/12 bit deep color (rev10) Patchwork
2019-05-04 2:00 ` ✓ Fi.CI.IGT: " Patchwork
2019-05-07 6:42 ` Jani Nikula [this message]
2019-05-07 10:34 ` [PATCH v9] drm/i915/icl: Set GCP_COLOR_INDICATION only for 10/12 bit deep color Ville Syrjälä
2019-05-07 11:19 ` Jani Nikula
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87h8a6n4t3.fsf@intel.com \
--to=jani.nikula@intel.com \
--cc=aditya.swarup@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox