From: Jerome Brunet <jbrunet@baylibre.com>
To: Neil Armstrong <neil.armstrong@linaro.org>,
Maarten Lankhorst <maarten.lankhorst@linux.intel.com>,
Maxime Ripard <mripard@kernel.org>,
Thomas Zimmermann <tzimmermann@suse.de>,
David Airlie <airlied@gmail.com>, Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Brunet <jbrunet@baylibre.com>,
Kevin Hilman <khilman@baylibre.com>,
Martin Blumenstingl <martin.blumenstingl@googlemail.com>,
dri-devel@lists.freedesktop.org,
linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: [PATCH 2/2] drm/meson: dw-hdmi: add bandgap setting for g12
Date: Fri, 26 Apr 2024 18:02:54 +0200 [thread overview]
Message-ID: <20240426160256.3089978-3-jbrunet@baylibre.com> (raw)
In-Reply-To: <20240426160256.3089978-1-jbrunet@baylibre.com>
When no mode is set, the utility pin appears to be grounded. No signal
is getting through.
This is problematic because ARC and eARC use this line and may do so even
if no display mode is set.
This change enable the bandgap setting on g12 chip, which fix the problem
with the utility pin. This is done by restoring init values on PHY init and
disable.
Fixes: 3b7c1237a72a ("drm/meson: Add G12A support for the DW-HDMI Glue")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
drivers/gpu/drm/meson/meson_dw_hdmi.c | 43 ++++++++++++++++-----------
1 file changed, 26 insertions(+), 17 deletions(-)
diff --git a/drivers/gpu/drm/meson/meson_dw_hdmi.c b/drivers/gpu/drm/meson/meson_dw_hdmi.c
index a83d93078537..5565f7777529 100644
--- a/drivers/gpu/drm/meson/meson_dw_hdmi.c
+++ b/drivers/gpu/drm/meson/meson_dw_hdmi.c
@@ -106,6 +106,8 @@
#define HHI_HDMI_CLK_CNTL 0x1cc /* 0x73 */
#define HHI_HDMI_PHY_CNTL0 0x3a0 /* 0xe8 */
#define HHI_HDMI_PHY_CNTL1 0x3a4 /* 0xe9 */
+#define PHY_CNTL1_INIT 0x03900000
+#define PHY_INVERT BIT(17)
#define HHI_HDMI_PHY_CNTL2 0x3a8 /* 0xea */
#define HHI_HDMI_PHY_CNTL3 0x3ac /* 0xeb */
#define HHI_HDMI_PHY_CNTL4 0x3b0 /* 0xec */
@@ -130,6 +132,8 @@ struct meson_dw_hdmi_data {
unsigned int addr);
void (*dwc_write)(struct meson_dw_hdmi *dw_hdmi,
unsigned int addr, unsigned int data);
+ u32 cntl0_init;
+ u32 cntl1_init;
};
struct meson_dw_hdmi {
@@ -458,7 +462,9 @@ static void dw_hdmi_phy_disable(struct dw_hdmi *hdmi,
DRM_DEBUG_DRIVER("\n");
- regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL0, 0);
+ /* Fallback to init mode */
+ regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL1, dw_hdmi->data->cntl1_init);
+ regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL0, dw_hdmi->data->cntl0_init);
}
static enum drm_connector_status dw_hdmi_read_hpd(struct dw_hdmi *hdmi,
@@ -576,11 +582,22 @@ static const struct regmap_config meson_dw_hdmi_regmap_config = {
.fast_io = true,
};
-static const struct meson_dw_hdmi_data meson_dw_hdmi_gx_data = {
+static const struct meson_dw_hdmi_data meson_dw_hdmi_gxbb_data = {
.top_read = dw_hdmi_top_read,
.top_write = dw_hdmi_top_write,
.dwc_read = dw_hdmi_dwc_read,
.dwc_write = dw_hdmi_dwc_write,
+ .cntl0_init = 0x0,
+ .cntl1_init = PHY_CNTL1_INIT | PHY_INVERT,
+};
+
+static const struct meson_dw_hdmi_data meson_dw_hdmi_gxl_data = {
+ .top_read = dw_hdmi_top_read,
+ .top_write = dw_hdmi_top_write,
+ .dwc_read = dw_hdmi_dwc_read,
+ .dwc_write = dw_hdmi_dwc_write,
+ .cntl0_init = 0x0,
+ .cntl1_init = PHY_CNTL1_INIT,
};
static const struct meson_dw_hdmi_data meson_dw_hdmi_g12a_data = {
@@ -588,6 +605,8 @@ static const struct meson_dw_hdmi_data meson_dw_hdmi_g12a_data = {
.top_write = dw_hdmi_g12a_top_write,
.dwc_read = dw_hdmi_g12a_dwc_read,
.dwc_write = dw_hdmi_g12a_dwc_write,
+ .cntl0_init = 0x000b4242, /* Bandgap */
+ .cntl1_init = PHY_CNTL1_INIT,
};
static void meson_dw_hdmi_init(struct meson_dw_hdmi *meson_dw_hdmi)
@@ -626,18 +645,8 @@ static void meson_dw_hdmi_init(struct meson_dw_hdmi *meson_dw_hdmi)
meson_dw_hdmi->data->top_write(meson_dw_hdmi, HDMITX_TOP_BIST_CNTL, BIT(12));
/* Setup PHY */
- regmap_update_bits(priv->hhi, HHI_HDMI_PHY_CNTL1,
- 0xffff << 16, 0x0390 << 16);
-
- /* BIT_INVERT */
- if (dw_hdmi_is_compatible(meson_dw_hdmi, "amlogic,meson-gxl-dw-hdmi") ||
- dw_hdmi_is_compatible(meson_dw_hdmi, "amlogic,meson-gxm-dw-hdmi") ||
- dw_hdmi_is_compatible(meson_dw_hdmi, "amlogic,meson-g12a-dw-hdmi"))
- regmap_update_bits(priv->hhi, HHI_HDMI_PHY_CNTL1,
- BIT(17), 0);
- else
- regmap_update_bits(priv->hhi, HHI_HDMI_PHY_CNTL1,
- BIT(17), BIT(17));
+ regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL1, meson_dw_hdmi->data->cntl1_init);
+ regmap_write(priv->hhi, HHI_HDMI_PHY_CNTL0, meson_dw_hdmi->data->cntl0_init);
/* Enable HDMI-TX Interrupt */
meson_dw_hdmi->data->top_write(meson_dw_hdmi, HDMITX_TOP_INTR_STAT_CLR,
@@ -848,11 +857,11 @@ static const struct dev_pm_ops meson_dw_hdmi_pm_ops = {
static const struct of_device_id meson_dw_hdmi_of_table[] = {
{ .compatible = "amlogic,meson-gxbb-dw-hdmi",
- .data = &meson_dw_hdmi_gx_data },
+ .data = &meson_dw_hdmi_gxbb_data },
{ .compatible = "amlogic,meson-gxl-dw-hdmi",
- .data = &meson_dw_hdmi_gx_data },
+ .data = &meson_dw_hdmi_gxl_data },
{ .compatible = "amlogic,meson-gxm-dw-hdmi",
- .data = &meson_dw_hdmi_gx_data },
+ .data = &meson_dw_hdmi_gxl_data },
{ .compatible = "amlogic,meson-g12a-dw-hdmi",
.data = &meson_dw_hdmi_g12a_data },
{ }
--
2.43.0
_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic
next prev parent reply other threads:[~2024-04-26 16:03 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-04-26 16:02 [PATCH 0/2] drm/meson: fix hdmi auxiliary system operation without display Jerome Brunet
2024-04-26 16:02 ` [PATCH 1/2] drm/meson: dw-hdmi: power up phy on device init Jerome Brunet
2024-05-03 8:42 ` Neil Armstrong
2024-04-26 16:02 ` Jerome Brunet [this message]
2024-05-03 8:46 ` [PATCH 2/2] drm/meson: dw-hdmi: add bandgap setting for g12 Neil Armstrong
2024-05-03 8:51 ` [PATCH 0/2] drm/meson: fix hdmi auxiliary system operation without display Neil Armstrong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240426160256.3089978-3-jbrunet@baylibre.com \
--to=jbrunet@baylibre.com \
--cc=airlied@gmail.com \
--cc=daniel@ffwll.ch \
--cc=dri-devel@lists.freedesktop.org \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=maarten.lankhorst@linux.intel.com \
--cc=martin.blumenstingl@googlemail.com \
--cc=mripard@kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=tzimmermann@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox