[PATCH v4 0/2] Add support for Amediatech X98Q (Amlogic S905W2)

[PATCH v4 0/2] Add support for Amediatech X98Q (Amlogic S905W2)

[christian.koever-draxl]

From: Christian Stefan Kövér-Draxl <christian.koever-draxl@student.uibk.ac.at>

Supported features:
- 1GB RAM (2GB variants exist)
- 10/100 Ethernet (Internal PHY)
- eMMC and SD card storage
- PWM-based CPU voltage regulation
- UART (Serial console)

Notes:
- The console uses uart_b at 921600 baud.
- Verified memory via /proc/device-tree; U-Boot patches the node.
- Tested on the 2GB RAM plus 16GB eMMC variant. 

Changes in v4:
- Add/Change hardware description to cover letter and dts patch.

Changes in v3:
- Change position of the entry in the amlogic.yaml.
- Change formatting of the Amlogic W150S1 Wi-Fi module comment.
- Fix several formatting issues.

Changes in v2:
- Split dt-bindings and dts changes into separate patches.
- Updated model string to match documented vendor prefix.
- Put vddio_sd states array in a single line.
- Added a comment for the unsupported Amlogic W150S1 Wi-Fi module. 

Christian Stefan Kövér-Draxl (2):
  dt-bindings: arm: amlogic: add support for Amediatech X98Q
  arm64: dts: amlogic: add support for Amediatech X98Q

 .../devicetree/bindings/arm/amlogic.yaml      |   7 +
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../boot/dts/amlogic/meson-s4-s905w2-x98q.dts | 249 ++++++++++++++++++
 3 files changed, 257 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts

-- 
2.53.0

[PATCH v4 1/2] dt-bindings: arm: amlogic: add support for Amediatech X98Q

[christian.koever-draxl]

From: Christian Stefan Kövér-Draxl <christian.koever-draxl@student.uibk.ac.at>

Add the board binding for the Amediatech X98Q TV box.

Signed-off-by: Christian Stefan Kövér-Draxl <christian.koever-draxl@student.uibk.ac.at>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index a885278bc4e2..c0167fbc310a 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -248,6 +248,13 @@ properties:
           - const: amlogic,s805x2
           - const: amlogic,s4
 
+      - description: Boards with the Amlogic Meson S4 S905W2 SoC
+        items:
+          - enum:
+              - amediatech,x98q
+          - const: amlogic,s905w2
+          - const: amlogic,s4
+
       - description: Boards with the Amlogic Meson S4 S905Y4 SoC
         items:
           - enum:
-- 
2.53.0

[PATCH v4 2/2] arm64: dts: amlogic: add support for Amediatech X98Q

[christian.koever-draxl]

From: Christian Stefan Kövér-Draxl <christian.koever-draxl@student.uibk.ac.at>

Add dts enabling core hardware for the Amediatech X98Q TV box.

The board features:
- Amlogic S905W2 (Meson S4) SoC
- 1 GiB RAM (2 GiB variants exist)
- eMMC and microSD card slot
- SDIO-based WiFi module (unsupported)
- RMII Ethernet with internal PHY
- IR receiver and UART console
- Status LED

Enabled peripherals:
- eMMC (HS200)
- SD card interface
- SDIO bus (WiFi, no driver yet)
- Ethernet (RMII)
- UART_B
- IR receiver
- PWM-controlled CPU regulator
- PWM and Fixed regulators for core and IO rails

Known limitations:
- No support for the onboard WiFi module
- Missing multimedia (HDMI/audio)

Signed-off-by: Christian Stefan Kövér-Draxl <christian.koever-draxl@student.uibk.ac.at>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../boot/dts/amlogic/meson-s4-s905w2-x98q.dts | 249 ++++++++++++++++++
 2 files changed, 250 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 15f9c817e502..c7752684dea6 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -85,6 +85,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-ugoos-am3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-s4-s905w2-x98q.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-s4-s905y4-khadas-vim1s.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts b/arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts
index 000000000000..3eecbc858522
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts
@@ -0,0 +1,249 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2026 Christian Stefan Köver-Draxl
+ * Based on meson-s4-s905y4-khadas-vim1s.dts:
+ *  - Copyright (c) 2026 Khadas Technology Co., Ltd.
+ */
+
+/dts-v1/;
+
+#include "meson-s4.dtsi"
+
+/ {
+	model = "Shenzhen Amediatech Technology Co., Ltd X98Q";
+	compatible = "amediatech,x98q", "amlogic,s905w2", "amlogic,s4";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		mmc0 = &emmc; /* eMMC */
+		mmc1 = &sd; /* SD card */
+		mmc2 = &sdio; /* SDIO */
+		serial0 = &uart_b;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 52 MiB reserved for ARM Trusted Firmware */
+		secmon_reserved: secmon@5000000 {
+			reg = <0x0 0x05000000 0x0 0x3400000>;
+			no-map;
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio GPIOB_9 GPIO_ACTIVE_LOW>;
+	};
+
+	sdio_32k: sdio-32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&sdio_32k>;
+		clock-names = "ext_clock";
+	};
+
+	main_5v: regulator-main-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	sd_3v3: regulator-sd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "SD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio GPIOD_4 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+	};
+
+	vddio_sd: regulator-vddio-sd {
+		compatible = "regulator-gpio";
+		regulator-name = "VDDIO_SD";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio GPIOD_9 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <1800000 1 3300000 0>;
+	};
+
+	vddao_3v3: regulator-vddao-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_5v>;
+		regulator-always-on;
+	};
+
+	vddio_ao1v8: regulator-vddio-ao1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	/* SY8120B1ABC DC/DC Regulator. */
+	vddcpu: regulator-vddcpu {
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <689000>;
+		regulator-max-microvolt = <1049000>;
+
+		vin-supply = <&main_5v>;
+
+		pwms = <&pwm_ij 1 1500 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+		/* Voltage Duty-Cycle */
+		voltage-table = <1049000 0>,
+				<1039000 3>,
+				<1029000 6>,
+				<1019000 9>,
+				<1009000 12>,
+				<999000 14>,
+				<989000 17>,
+				<979000 20>,
+				<969000 23>,
+				<959000 26>,
+				<949000 29>,
+				<939000 31>,
+				<929000 34>,
+				<919000 37>,
+				<909000 40>,
+				<899000 43>,
+				<889000 45>,
+				<879000 48>,
+				<869000 51>,
+				<859000 54>,
+				<849000 56>,
+				<839000 59>,
+				<829000 62>,
+				<819000 65>,
+				<809000 68>,
+				<799000 70>,
+				<789000 73>,
+				<779000 76>,
+				<769000 79>,
+				<759000 81>,
+				<749000 84>,
+				<739000 87>,
+				<729000 89>,
+				<719000 92>,
+				<709000 95>,
+				<699000 98>,
+				<689000 100>;
+	};
+};
+
+&emmc {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_ao1v8>;
+};
+
+&ethmac {
+	status = "okay";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins1>;
+	pinctrl-names = "default";
+};
+
+&pwm_ij {
+	status = "okay";
+};
+
+&sd {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_3v3>;
+};
+
+     /*
+      * Wireless SDIO Module (Amlogic W150S1)
+      * Note: There is no driver for this at the moment.
+      */
+
+&sdio {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	no-sd;
+	no-mmc;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_ao1v8>;
+};
+
+&uart_b {
+	status = "okay";
+};
-- 
2.53.0

Re: [PATCH v4 2/2] arm64: dts: amlogic: add support for Amediatech X98Q

[Ferass El Hafidi]

On Wed, 22 Apr 2026 09:58, christian.koever-draxl@student.uibk.ac.at wrote:
>From: Christian Stefan Kövér-Draxl <christian.koever-draxl@student.uibk.ac.at>
>
>Add dts enabling core hardware for the Amediatech X98Q TV box.
>
>The board features:
>- Amlogic S905W2 (Meson S4) SoC
>- 1 GiB RAM (2 GiB variants exist)
>- eMMC and microSD card slot
>- SDIO-based WiFi module (unsupported)
>- RMII Ethernet with internal PHY
>- IR receiver and UART console
>- Status LED
>
>Enabled peripherals:
>- eMMC (HS200)
>- SD card interface
>- SDIO bus (WiFi, no driver yet)
>- Ethernet (RMII)
>- UART_B
>- IR receiver
>- PWM-controlled CPU regulator
>- PWM and Fixed regulators for core and IO rails
>
>Known limitations:
>- No support for the onboard WiFi module
>- Missing multimedia (HDMI/audio)
>
>Signed-off-by: Christian Stefan Kövér-Draxl <christian.koever-draxl@student.uibk.ac.at>
>---
> arch/arm64/boot/dts/amlogic/Makefile          |   1 +
> .../boot/dts/amlogic/meson-s4-s905w2-x98q.dts | 249 ++++++++++++++++++
> 2 files changed, 250 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts
><...>
>+&sd {
>+	status = "okay";
>+	pinctrl-0 = <&sdcard_pins>;
>+	pinctrl-1 = <&sdcard_clk_gate_pins>;
>+	pinctrl-names = "default", "clk-gate";
>+	bus-width = <4>;
>+	cap-sd-highspeed;
>+	max-frequency = <50000000>;
>+	disable-wp;
>+
>+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
>+
>+	vmmc-supply = <&vddao_3v3>;
>+	vqmmc-supply = <&vddao_3v3>;
>+};
>+
>+     /*
>+      * Wireless SDIO Module (Amlogic W150S1)
>+      * Note: There is no driver for this at the moment.
>+      */
>+

I didn't mean to indent, just to align the '*'.
Sorry it wasn't clear.

>+&sdio {
>+	status = "okay";
>+	pinctrl-0 = <&sdio_pins>;
>+	pinctrl-1 = <&sdio_clk_gate_pins>;
>+	pinctrl-names = "default", "clk-gate";
>+	#address-cells = <1>;
>+	#size-cells = <0>;
>+	bus-width = <4>;
>+	cap-sd-highspeed;
>+	sd-uhs-sdr50;
>+	sd-uhs-sdr104;
>+	max-frequency = <200000000>;
>+	non-removable;
>+	disable-wp;
>+
>+	no-sd;
>+	no-mmc;
>+	mmc-pwrseq = <&sdio_pwrseq>;
>+	vmmc-supply = <&vddao_3v3>;
>+	vqmmc-supply = <&vddio_ao1v8>;
>+};
>+
>+&uart_b {
>+	status = "okay";
>+};
>-- 
>2.53.0

--
Best regards,
Ferass

Re: [PATCH v4 2/2] arm64: dts: amlogic: add support for Amediatech X98Q

[Christian Hewitt]

> On 22 Apr 2026, at 1:58 pm, christian.koever-draxl@student.uibk.ac.at wrote:
> 
> From: Christian Stefan Kövér-Draxl <christian.koever-draxl@student.uibk.ac.at>
> 
> Add dts enabling core hardware for the Amediatech X98Q TV box.
> 
> The board features:
> - Amlogic S905W2 (Meson S4) SoC
> - 1 GiB RAM (2 GiB variants exist)
> - eMMC and microSD card slot
> - SDIO-based WiFi module (unsupported)
> - RMII Ethernet with internal PHY
> - IR receiver and UART console
> - Status LED
> 
> Enabled peripherals:
> - eMMC (HS200)
> - SD card interface
> - SDIO bus (WiFi, no driver yet)
> - Ethernet (RMII)
> - UART_B
> - IR receiver
> - PWM-controlled CPU regulator
> - PWM and Fixed regulators for core and IO rails
> 
> Known limitations:
> - No support for the onboard WiFi module
> - Missing multimedia (HDMI/audio)
> 
> Signed-off-by: Christian Stefan Kövér-Draxl <christian.koever-draxl@student.uibk.ac.at>
> ---
> arch/arm64/boot/dts/amlogic/Makefile          |   1 +
> .../boot/dts/amlogic/meson-s4-s905w2-x98q.dts | 249 ++++++++++++++++++
> 2 files changed, 250 insertions(+)
> create mode 100644 arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 15f9c817e502..c7752684dea6 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -85,6 +85,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-ugoos-am3.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-s4-s905w2-x98q.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-s4-s905y4-khadas-vim1s.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
> dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts b/arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts
> index 000000000000..3eecbc858522
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-s4-s905w2-x98q.dts
> @@ -0,0 +1,249 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2026 Christian Stefan Köver-Draxl
> + * Based on meson-s4-s905y4-khadas-vim1s.dts:
> + *  - Copyright (c) 2026 Khadas Technology Co., Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-s4.dtsi"
> +
> +/ {
> + model = "Shenzhen Amediatech Technology Co., Ltd X98Q";
> + compatible = "amediatech,x98q", "amlogic,s905w2", "amlogic,s4";
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + aliases {
> + mmc0 = &emmc; /* eMMC */
> + mmc1 = &sd; /* SD card */
> + mmc2 = &sdio; /* SDIO */
> + serial0 = &uart_b;
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x40000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* 52 MiB reserved for ARM Trusted Firmware */
> + secmon_reserved: secmon@5000000 {
> + reg = <0x0 0x05000000 0x0 0x3400000>;
> + no-map;
> + };
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio GPIOB_9 GPIO_ACTIVE_LOW>;
> + };
> +
> + sdio_32k: sdio-32k {
> + compatible = "pwm-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> + };
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> + clocks = <&sdio_32k>;
> + clock-names = "ext_clock";
> + };
> +
> + main_5v: regulator-main-5v {
> + compatible = "regulator-fixed";
> + regulator-name = "5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + sd_3v3: regulator-sd-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "SD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio GPIOD_4 GPIO_ACTIVE_LOW>;
> + regulator-always-on;
> + };
> +
> + vddio_sd: regulator-vddio-sd {
> + compatible = "regulator-gpio";
> + regulator-name = "VDDIO_SD";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + gpios = <&gpio GPIOD_9 GPIO_ACTIVE_HIGH>;
> + gpios-states = <1>;
> + states = <1800000 1 3300000 0>;
> + };
> +
> + vddao_3v3: regulator-vddao-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDAO_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&main_5v>;
> + regulator-always-on;
> + };
> +
> + vddio_ao1v8: regulator-vddio-ao1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddao_3v3>;
> + regulator-always-on;
> + };
> +
> + /* SY8120B1ABC DC/DC Regulator. */
> + vddcpu: regulator-vddcpu {
> + compatible = "pwm-regulator";
> +
> + regulator-name = "VDDCPU";
> + regulator-min-microvolt = <689000>;
> + regulator-max-microvolt = <1049000>;
> +
> + vin-supply = <&main_5v>;
> +
> + pwms = <&pwm_ij 1 1500 0>;
> + pwm-dutycycle-range = <100 0>;
> +
> + regulator-boot-on;
> + regulator-always-on;
> + /* Voltage Duty-Cycle */
> + voltage-table = <1049000 0>,
> + <1039000 3>,
> + <1029000 6>,
> + <1019000 9>,
> + <1009000 12>,
> + <999000 14>,
> + <989000 17>,
> + <979000 20>,
> + <969000 23>,
> + <959000 26>,
> + <949000 29>,
> + <939000 31>,
> + <929000 34>,
> + <919000 37>,
> + <909000 40>,
> + <899000 43>,
> + <889000 45>,
> + <879000 48>,
> + <869000 51>,
> + <859000 54>,
> + <849000 56>,
> + <839000 59>,
> + <829000 62>,
> + <819000 65>,
> + <809000 68>,
> + <799000 70>,
> + <789000 73>,
> + <779000 76>,
> + <769000 79>,
> + <759000 81>,
> + <749000 84>,
> + <739000 87>,
> + <729000 89>,
> + <719000 92>,
> + <709000 95>,
> + <699000 98>,
> + <689000 100>;
> + };
> +};
> +
> +&emmc {
> + status = "okay";
> + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddio_ao1v8>;
> +};
> +
> +&ethmac {
> + status = "okay";
> + phy-handle = <&internal_ephy>;
> + phy-mode = "rmii";
> +};
> +
> +&ir {
> + status = "okay";
> + pinctrl-0 = <&remote_pins>;
> + pinctrl-names = "default";
> +};
> +
> +&pwm_ef {
> + status = "okay";
> + pinctrl-0 = <&pwm_e_pins1>;
> + pinctrl-names = "default";
> +};
> +
> +&pwm_ij {
> + status = "okay";
> +};
> +
> +&sd {
> + status = "okay";
> + pinctrl-0 = <&sdcard_pins>;
> + pinctrl-1 = <&sdcard_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> + bus-width = <4>;
> + cap-sd-highspeed;
> + max-frequency = <50000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
> +
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddao_3v3>;
> +};
> +
> +     /*
> +      * Wireless SDIO Module (Amlogic W150S1)
> +      * Note: There is no driver for this at the moment.
> +      */

^ drop this comment

> +
> +&sdio {
> + status = "okay";
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-1 = <&sdio_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + bus-width = <4>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + max-frequency = <200000000>;
> + non-removable;
> + disable-wp;
> +
> + no-sd;
> + no-mmc;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + vmmc-supply = <&vddao_3v3>;
> + vqmmc-supply = <&vddio_ao1v8>;

	sdio: wifi@1 {
		/* Amlogic W150S1 */
		reg = <1>;
  	};

^ add this to generically describe the hardware without
the need for a specific compatible (as done in several of
the Amlogic reference designs where we cannot guarantee
which chipset is used). The reg value should be enough to
result in the downstream driver probing should a distro
choose to package it; thus avoiding the need for distros
to forever carry a device-tree patch to add support (as
Amlogic have no plans to upstream the driver). Should that
ever change the comment can be replaced with a compatible.

Christian

> +};
> +
> +&uart_b {
> + status = "okay";
> +};
> -- 
> 2.53.0
> 
> 
> _______________________________________________
> linux-amlogic mailing list
> linux-amlogic@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-amlogic