[PATCH v4 0/3] MT8173 HDMI 4K support

[PATCH v4 0/3] MT8173 HDMI 4K support

[Bibby Hsieh]

This is MT8173 HDMI 4K support PATCH v4, based on 4.8-rc1.

In order to support HDMI 4K on MT8173,
we have to make some modifications.
1) Make sure that mtk_hdmi_send_infoframe is sent successfully.
2) Enhance the HDMI driving current to improve performance.
3) Make sure that pixel clock is 297MHz when resolution is 4K.

Changes since v3:
 - Rebase to 4.8-rc1.
 - The valid range of tvdpll is 1G to 2G Hz, so, we Change the
   if statement of mode->clock to fit that and add a comment.

Changes since v2:
 - Remove the change about preparation for MT2701 support.

Changes since v1:
 - According to the suggestion from philipp, We use the new
   dpi0_sel rate set method.
 - calls clk_set_rate to set the dpi0_sel according to the
   pixel clock.
 - Remove the direct access to all the intermediate clock part.
 - Remove the intermediate tvdpll_d* clocks in dts.
 - According to suggestion from CK, we rename the clock parse
   function and remove it from mtk_dpi_conf struct.
 - Merges the hdmi Pll set rate for pixel clock greater than
   165MHz and smaller parts.

The PATCH depends on the following patch:
https://patchwork.kernel.org/patch/9262575/
(arm64: dts: mt8173: add mmsel clocks for 4K support)

Junzhi Zhao (3):
  drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable
  drm/mediatek: enhance the HDMI driving current
  drm/mediatek: fix the wrong pixel clock when resolution is 4K

 drivers/gpu/drm/mediatek/mtk_dpi.c             |    9 +++--
 drivers/gpu/drm/mediatek/mtk_hdmi.c            |   17 ++++++----
 drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
 3 files changed, 48 insertions(+), 20 deletions(-)

-- 
1.7.9.5

[PATCH v4 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

The mtk_hdmi_send_infoframe have to
be run after PLL and PIXEL clock of HDMI enable.
Make sure that HDMI inforframes can be sent
successfully.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_hdmi.c |   17 +++++++++++------
 1 file changed, 11 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
index 334562d..875b045 100644
--- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
+++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
@@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
 	phy_power_on(hdmi->phy);
 	mtk_hdmi_aud_output_config(hdmi, mode);
 
-	mtk_hdmi_setup_audio_infoframe(hdmi);
-	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
-	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
-	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
-		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
-
 	mtk_hdmi_hw_vid_black(hdmi, false);
 	mtk_hdmi_hw_aud_unmute(hdmi);
 	mtk_hdmi_hw_send_av_unmute(hdmi);
@@ -1401,6 +1395,16 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
 	hdmi->powered = true;
 }
 
+static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
+				    struct drm_display_mode *mode)
+{
+	mtk_hdmi_setup_audio_infoframe(hdmi);
+	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
+	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
+	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
+		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
+}
+
 static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
 {
 	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
@@ -1409,6 +1413,7 @@ static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
 	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
 	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
 	phy_power_on(hdmi->phy);
+	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
 
 	hdmi->enabled = true;
 }
-- 
1.7.9.5

[PATCH v4 2/3] drm/mediatek: enhance the HDMI driving current

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

In order to improve 4K resolution performance,
we have to enhance the HDMI driving current
when clock rate is greater than 165MHz.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c |   42 +++++++++++++++++-------
 1 file changed, 30 insertions(+), 12 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
index 8a24754..51cb9cf 100644
--- a/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
+++ b/drivers/gpu/drm/mediatek/mtk_mt8173_hdmi_phy.c
@@ -265,6 +265,9 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 	struct mtk_hdmi_phy *hdmi_phy = to_mtk_hdmi_phy(hw);
 	unsigned int pre_div;
 	unsigned int div;
+	unsigned int pre_ibias;
+	unsigned int hdmi_ibias;
+	unsigned int imp_en;
 
 	dev_dbg(hdmi_phy->dev, "%s: %lu Hz, parent: %lu Hz\n", __func__,
 		rate, parent_rate);
@@ -298,18 +301,31 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 			  (0x1 << PLL_BR_SHIFT),
 			  RG_HDMITX_PLL_BP | RG_HDMITX_PLL_BC |
 			  RG_HDMITX_PLL_BR);
-	mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3, RG_HDMITX_PRD_IMP_EN);
+	if (rate < 165000000) {
+		mtk_hdmi_phy_clear_bits(hdmi_phy, HDMI_CON3,
+					RG_HDMITX_PRD_IMP_EN);
+		pre_ibias = 0x3;
+		imp_en = 0x0;
+		hdmi_ibias = hdmi_phy->ibias;
+	} else {
+		mtk_hdmi_phy_set_bits(hdmi_phy, HDMI_CON3,
+				      RG_HDMITX_PRD_IMP_EN);
+		pre_ibias = 0x6;
+		imp_en = 0xf;
+		hdmi_ibias = hdmi_phy->ibias_up;
+	}
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON4,
-			  (0x3 << PRD_IBIAS_CLK_SHIFT) |
-			  (0x3 << PRD_IBIAS_D2_SHIFT) |
-			  (0x3 << PRD_IBIAS_D1_SHIFT) |
-			  (0x3 << PRD_IBIAS_D0_SHIFT),
+			  (pre_ibias << PRD_IBIAS_CLK_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D2_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D1_SHIFT) |
+			  (pre_ibias << PRD_IBIAS_D0_SHIFT),
 			  RG_HDMITX_PRD_IBIAS_CLK |
 			  RG_HDMITX_PRD_IBIAS_D2 |
 			  RG_HDMITX_PRD_IBIAS_D1 |
 			  RG_HDMITX_PRD_IBIAS_D0);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON3,
-			  (0x0 << DRV_IMP_EN_SHIFT), RG_HDMITX_DRV_IMP_EN);
+			  (imp_en << DRV_IMP_EN_SHIFT),
+			  RG_HDMITX_DRV_IMP_EN);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON6,
 			  (hdmi_phy->drv_imp_clk << DRV_IMP_CLK_SHIFT) |
 			  (hdmi_phy->drv_imp_d2 << DRV_IMP_D2_SHIFT) |
@@ -318,12 +334,14 @@ static int mtk_hdmi_pll_set_rate(struct clk_hw *hw, unsigned long rate,
 			  RG_HDMITX_DRV_IMP_CLK | RG_HDMITX_DRV_IMP_D2 |
 			  RG_HDMITX_DRV_IMP_D1 | RG_HDMITX_DRV_IMP_D0);
 	mtk_hdmi_phy_mask(hdmi_phy, HDMI_CON5,
-			  (hdmi_phy->ibias << DRV_IBIAS_CLK_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D2_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D1_SHIFT) |
-			  (hdmi_phy->ibias << DRV_IBIAS_D0_SHIFT),
-			  RG_HDMITX_DRV_IBIAS_CLK | RG_HDMITX_DRV_IBIAS_D2 |
-			  RG_HDMITX_DRV_IBIAS_D1 | RG_HDMITX_DRV_IBIAS_D0);
+			  (hdmi_ibias << DRV_IBIAS_CLK_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D2_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D1_SHIFT) |
+			  (hdmi_ibias << DRV_IBIAS_D0_SHIFT),
+			  RG_HDMITX_DRV_IBIAS_CLK |
+			  RG_HDMITX_DRV_IBIAS_D2 |
+			  RG_HDMITX_DRV_IBIAS_D1 |
+			  RG_HDMITX_DRV_IBIAS_D0);
 	return 0;
 }
 
-- 
1.7.9.5

[PATCH v4 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[Bibby Hsieh]

From: Junzhi Zhao <junzhi.zhao@mediatek.com>

Pixel clock should be 297MHz when resolution is 4K.

Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dpi.c |    9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
index 0186e50..90fb831 100644
--- a/drivers/gpu/drm/mediatek/mtk_dpi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
@@ -432,11 +432,16 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
 	unsigned long pll_rate;
 	unsigned int factor;
 
+	/* let pll_rate can fix the valid range of tvdpll (1G~2GHz) */
 	pix_rate = 1000UL * mode->clock;
-	if (mode->clock <= 74000)
+	if (mode->clock <= 27000)
+		factor = 16 * 3;
+	else if (mode->clock <= 84000)
 		factor = 8 * 3;
-	else
+	else if (mode->clock <= 167000)
 		factor = 4 * 3;
+	else
+		factor = 2 * 3;
 	pll_rate = pix_rate * factor;
 
 	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",
-- 
1.7.9.5

[PATCH v4 3/3] drm/mediatek: fix the wrong pixel clock when resolution is 4K

[CK Hu]

Hi, Bibby:

Sorry for the late reply.

On Wed, 2016-08-17 at 14:58 +0800, Bibby Hsieh wrote:
> From: Junzhi Zhao <junzhi.zhao@mediatek.com>
> 
> Pixel clock should be 297MHz when resolution is 4K.
> 

>From the code you modified, I think title should be: "Enlarge pll_rate
range from (<original lower bound>, <original upper bound>) to (<new
lower bound>, <new upper bound>)"

In description, you can explain the pll_rate for 4K and this enlargement
could support more resolution include 4K (Not only 4K).

> Signed-off-by: Junzhi Zhao <junzhi.zhao@mediatek.com>
> Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dpi.c |    9 +++++++--
>  1 file changed, 7 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dpi.c b/drivers/gpu/drm/mediatek/mtk_dpi.c
> index 0186e50..90fb831 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dpi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dpi.c
> @@ -432,11 +432,16 @@ static int mtk_dpi_set_display_mode(struct mtk_dpi *dpi,
>  	unsigned long pll_rate;
>  	unsigned int factor;
>  
> +	/* let pll_rate can fix the valid range of tvdpll (1G~2GHz) */
>  	pix_rate = 1000UL * mode->clock;
> -	if (mode->clock <= 74000)
> +	if (mode->clock <= 27000)
> +		factor = 16 * 3;
> +	else if (mode->clock <= 84000)
>  		factor = 8 * 3;
> -	else
> +	else if (mode->clock <= 167000)
>  		factor = 4 * 3;
> +	else
> +		factor = 2 * 3;
>  	pll_rate = pix_rate * factor;
>  
>  	dev_dbg(dpi->dev, "Want PLL %lu Hz, pixel clock %lu Hz\n",

Regards,
CK