* [PATCH 1/5] arm: dts: mt2701: Add ethernet device node
2017-08-01 7:03 [PATCH 0/5] Add some DT nodes for Mediatek MT2701 Erin Lo
@ 2017-08-01 7:03 ` Erin Lo
2017-08-01 7:03 ` [PATCH 2/5] arm: dts: mt2701: Add display bls related nodes for MT2701 Erin Lo
` (4 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Erin Lo @ 2017-08-01 7:03 UTC (permalink / raw)
To: linux-arm-kernel
From: Sean Wang <sean.wang@mediatek.com>
Add ethernet device node for MT2701
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
---
arch/arm/boot/dts/mt2701.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi
index f1efdc6..0619b86 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mt2701.dtsi
@@ -597,6 +597,30 @@
#clock-cells = <1>;
};
+ eth: ethernet at 1b100000 {
+ compatible = "mediatek,mt2701-eth", "syscon";
+ reg = <0 0x1b100000 0 0x20000>;
+ interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 199 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
+ <ðsys CLK_ETHSYS_ESW>,
+ <ðsys CLK_ETHSYS_GP1>,
+ <ðsys CLK_ETHSYS_GP2>,
+ <&apmixedsys CLK_APMIXED_TRGPLL>;
+ clock-names = "ethif", "esw", "gp1", "gp2", "trgpll";
+ resets = <ðsys MT2701_ETHSYS_FE_RST>,
+ <ðsys MT2701_ETHSYS_GMAC_RST>,
+ <ðsys MT2701_ETHSYS_PPE_RST>;
+ reset-names = "fe", "gmac", "ppe";
+ power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>;
+ mediatek,ethsys = <ðsys>;
+ mediatek,pctl = <&syscfg_pctl_a>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
bdpsys: syscon at 1c000000 {
compatible = "mediatek,mt2701-bdpsys", "syscon";
reg = <0 0x1c000000 0 0x1000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 2/5] arm: dts: mt2701: Add display bls related nodes for MT2701
2017-08-01 7:03 [PATCH 0/5] Add some DT nodes for Mediatek MT2701 Erin Lo
2017-08-01 7:03 ` [PATCH 1/5] arm: dts: mt2701: Add ethernet device node Erin Lo
@ 2017-08-01 7:03 ` Erin Lo
2017-08-01 7:03 ` [PATCH 3/5] " Erin Lo
` (3 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Erin Lo @ 2017-08-01 7:03 UTC (permalink / raw)
To: linux-arm-kernel
From: Weiqing Kong <weiqing.kong@mediatek.com>
This patch adds the device node of display backlight for MT2701
Signed-off-by: Weiqing Kong <weiqing.kong@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
---
arch/arm/boot/dts/mt2701.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi
index 0619b86..2bcf739 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mt2701.dtsi
@@ -529,6 +529,15 @@
#clock-cells = <1>;
};
+ bls: bls at 1400a000 {
+ compatible = "mediatek,mt2701-disp-pwm";
+ reg = <0 0x1400a000 0 0x1000>;
+ #pwm-cells = <2>;
+ clocks = <&mmsys CLK_MM_MDP_BLS_26M>, <&mmsys CLK_MM_DISP_BLS>;
+ clock-names = "main", "mm";
+ status = "disabled";
+ };
+
larb0: larb at 14010000 {
compatible = "mediatek,mt2701-smi-larb";
reg = <0 0x14010000 0 0x1000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 3/5] arm: dts: mt2701: Add display bls related nodes for MT2701
2017-08-01 7:03 [PATCH 0/5] Add some DT nodes for Mediatek MT2701 Erin Lo
2017-08-01 7:03 ` [PATCH 1/5] arm: dts: mt2701: Add ethernet device node Erin Lo
2017-08-01 7:03 ` [PATCH 2/5] arm: dts: mt2701: Add display bls related nodes for MT2701 Erin Lo
@ 2017-08-01 7:03 ` Erin Lo
2017-08-01 7:03 ` [PATCH 4/5] arm: dts: mt2701: Add display subsystem " Erin Lo
` (2 subsequent siblings)
5 siblings, 0 replies; 8+ messages in thread
From: Erin Lo @ 2017-08-01 7:03 UTC (permalink / raw)
To: linux-arm-kernel
From: Weiqing Kong <weiqing.kong@mediatek.com>
This patch adds board related config for backlight
Signed-off-by: Weiqing Kong <weiqing.kong@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
---
arch/arm/boot/dts/mt2701-evb.dts | 27 +++++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm/boot/dts/mt2701-evb.dts b/arch/arm/boot/dts/mt2701-evb.dts
index f484973..b96e34d 100644
--- a/arch/arm/boot/dts/mt2701-evb.dts
+++ b/arch/arm/boot/dts/mt2701-evb.dts
@@ -23,6 +23,19 @@
reg = <0 0x80000000 0 0x40000000>;
};
+ backlight_lcd: backlight_lcd {
+ compatible = "pwm-backlight";
+ pwms = <&bls 0 100000>;
+ brightness-levels = <
+ 0 16 32 48 64 80 96 112
+ 128 144 160 176 192 208 224 240
+ 255
+ >;
+ default-brightness-level = <9>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_bls_gpio>;
+ };
+
sound:sound {
compatible = "mediatek,mt2701-cs42448-machine";
mediatek,platform = <&afe>;
@@ -62,6 +75,10 @@
status = "okay";
};
+&bls {
+ status = "okay";
+};
+
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
@@ -86,6 +103,10 @@
};
};
+&mmsys {
+ status = "okay";
+};
+
&pio {
i2c0_pins_a: i2c0 at 0 {
pins1 {
@@ -111,6 +132,12 @@
};
};
+ pwm_bls_gpio: pwm_bls_gpio {
+ pins_cmd_dat {
+ pinmux = <MT2701_PIN_208_AUD_EXT_CK1__FUNC_DISP_PWM>;
+ };
+ };
+
spi_pins_a: spi0 at 0 {
pins_spi {
pinmux = <MT2701_PIN_53_SPI0_CSN__FUNC_SPI0_CS>,
--
1.9.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 4/5] arm: dts: mt2701: Add display subsystem related nodes for MT2701
2017-08-01 7:03 [PATCH 0/5] Add some DT nodes for Mediatek MT2701 Erin Lo
` (2 preceding siblings ...)
2017-08-01 7:03 ` [PATCH 3/5] " Erin Lo
@ 2017-08-01 7:03 ` Erin Lo
2017-08-01 7:03 ` [PATCH 5/5] arm: dts: mt2701: Add usb3 device nodes Erin Lo
2017-08-01 14:06 ` [PATCH 0/5] Add some DT nodes for Mediatek MT2701 Matthias Brugger
5 siblings, 0 replies; 8+ messages in thread
From: Erin Lo @ 2017-08-01 7:03 UTC (permalink / raw)
To: linux-arm-kernel
From: YT Shen <yt.shen@mediatek.com>
This patch adds the device nodes for the DISP function blocks for MT2701
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
---
arch/arm/boot/dts/mt2701.dtsi | 77 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 77 insertions(+)
diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi
index 2bcf739..efb5118 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mt2701.dtsi
@@ -25,6 +25,11 @@
compatible = "mediatek,mt2701";
interrupt-parent = <&cirq>;
+ aliases {
+ rdma0 = &rdma0;
+ rdma1 = &rdma1;
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
@@ -202,6 +207,16 @@
power-domains = <&scpsys MT2701_POWER_DOMAIN_DISP>;
};
+ mipi_tx0: mipi-dphy at 10010000 {
+ compatible = "mediatek,mt2701-mipi-tx";
+ reg = <0 0x10010000 0 0x90>;
+ clocks = <&clk26m>;
+ clock-output-names = "mipi_tx0_pll";
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
sysirq: interrupt-controller at 10200100 {
compatible = "mediatek,mt2701-sysirq",
"mediatek,mt6577-sysirq";
@@ -529,6 +544,33 @@
#clock-cells = <1>;
};
+ ovl at 14007000 {
+ compatible = "mediatek,mt2701-disp-ovl";
+ reg = <0 0x14007000 0 0x1000>;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_DISP_OVL>;
+ iommus = <&iommu MT2701_M4U_PORT_DISP_OVL_0>;
+ mediatek,larb = <&larb0>;
+ };
+
+ rdma0: rdma at 14008000 {
+ compatible = "mediatek,mt2701-disp-rdma";
+ reg = <0 0x14008000 0 0x1000>;
+ interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_DISP_RDMA>;
+ iommus = <&iommu MT2701_M4U_PORT_DISP_RDMA>;
+ mediatek,larb = <&larb0>;
+ };
+
+ wdma at 14009000 {
+ compatible = "mediatek,mt2701-disp-wdma";
+ reg = <0 0x14009000 0 0x1000>;
+ interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_DISP_WDMA>;
+ iommus = <&iommu MT2701_M4U_PORT_DISP_WDMA>;
+ mediatek,larb = <&larb0>;
+ };
+
bls: bls at 1400a000 {
compatible = "mediatek,mt2701-disp-pwm";
reg = <0 0x1400a000 0 0x1000>;
@@ -538,6 +580,32 @@
status = "disabled";
};
+ color at 1400b000 {
+ compatible = "mediatek,mt2701-disp-color";
+ reg = <0 0x1400b000 0 0x1000>;
+ interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_DISP_COLOR>;
+ };
+
+ dsi: dsi at 1400c000 {
+ compatible = "mediatek,mt2701-dsi";
+ reg = <0 0x1400c000 0 0x1000>;
+ interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_DSI_ENGINE>, <&mmsys CLK_MM_DSI_DIG>,
+ <&mipi_tx0>;
+ clock-names = "engine", "digital", "hs";
+ phys = <&mipi_tx0>;
+ phy-names = "dphy";
+ status = "disabled";
+ };
+
+ mutex: mutex at 1400e000 {
+ compatible = "mediatek,mt2701-disp-mutex";
+ reg = <0 0x1400e000 0 0x1000>;
+ interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_MUTEX_32K>;
+ };
+
larb0: larb at 14010000 {
compatible = "mediatek,mt2701-smi-larb";
reg = <0 0x14010000 0 0x1000>;
@@ -548,6 +616,15 @@
power-domains = <&scpsys MT2701_POWER_DOMAIN_DISP>;
};
+ rdma1: rdma at 14012000 {
+ compatible = "mediatek,mt2701-disp-rdma";
+ reg = <0 0x14012000 0 0x1000>;
+ interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_DISP_RDMA1>;
+ iommus = <&iommu MT2701_M4U_PORT_DISP_RDMA1>;
+ mediatek,larb = <&larb0>;
+ };
+
imgsys: syscon at 15000000 {
compatible = "mediatek,mt2701-imgsys", "syscon";
reg = <0 0x15000000 0 0x1000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 5/5] arm: dts: mt2701: Add usb3 device nodes
2017-08-01 7:03 [PATCH 0/5] Add some DT nodes for Mediatek MT2701 Erin Lo
` (3 preceding siblings ...)
2017-08-01 7:03 ` [PATCH 4/5] arm: dts: mt2701: Add display subsystem " Erin Lo
@ 2017-08-01 7:03 ` Erin Lo
2017-08-01 14:06 ` [PATCH 0/5] Add some DT nodes for Mediatek MT2701 Matthias Brugger
5 siblings, 0 replies; 8+ messages in thread
From: Erin Lo @ 2017-08-01 7:03 UTC (permalink / raw)
To: linux-arm-kernel
From: Chunfeng Yun <chunfeng.yun@mediatek.com>
Add xhci nodes and usb3 phy nodes for MT2701
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
---
arch/arm/boot/dts/mt2701.dtsi | 79 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 79 insertions(+)
diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi
index efb5118..16242f5 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mt2701.dtsi
@@ -13,6 +13,7 @@
*/
#include <dt-bindings/clock/mt2701-clk.h>
+#include <dt-bindings/phy/phy.h>
#include <dt-bindings/power/mt2701-power.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -677,6 +678,84 @@
#clock-cells = <1>;
};
+ usb0: usb at 1a1c0000 {
+ compatible = "mediatek,mt8173-xhci";
+ reg = <0 0x1a1c0000 0 0x1000>,
+ <0 0x1a1c4700 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&hifsys CLK_HIFSYS_USB0PHY>,
+ <&topckgen CLK_TOP_ETHIF_SEL>;
+ clock-names = "sys_ck", "ref_ck";
+ power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
+ phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
+ status = "disabled";
+ };
+
+ u3phy0: usb-phy at 1a1c4000 {
+ compatible = "mediatek,mt2701-u3phy";
+ reg = <0 0x1a1c4000 0 0x0700>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ u2port0: usb-phy at 1a1c4800 {
+ reg = <0 0x1a1c4800 0 0x0100>;
+ clocks = <&topckgen CLK_TOP_USB_PHY48M>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+
+ u3port0: usb-phy at 1a1c4900 {
+ reg = <0 0x1a1c4900 0 0x0700>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+ };
+
+ usb1: usb at 1a240000 {
+ compatible = "mediatek,mt8173-xhci";
+ reg = <0 0x1a240000 0 0x1000>,
+ <0 0x1a244700 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&hifsys CLK_HIFSYS_USB1PHY>,
+ <&topckgen CLK_TOP_ETHIF_SEL>;
+ clock-names = "sys_ck", "ref_ck";
+ power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
+ phys = <&u2port1 PHY_TYPE_USB2>, <&u3port1 PHY_TYPE_USB3>;
+ status = "disabled";
+ };
+
+ u3phy1: usb-phy at 1a244000 {
+ compatible = "mediatek,mt2701-u3phy";
+ reg = <0 0x1a244000 0 0x0700>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ u2port1: usb-phy at 1a244800 {
+ reg = <0 0x1a244800 0 0x0100>;
+ clocks = <&topckgen CLK_TOP_USB_PHY48M>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+
+ u3port1: usb-phy at 1a244900 {
+ reg = <0 0x1a244900 0 0x0700>;
+ clocks = <&clk26m>;
+ clock-names = "ref";
+ #phy-cells = <1>;
+ status = "okay";
+ };
+ };
+
ethsys: syscon at 1b000000 {
compatible = "mediatek,mt2701-ethsys", "syscon";
reg = <0 0x1b000000 0 0x1000>;
--
1.9.1
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 0/5] Add some DT nodes for Mediatek MT2701
2017-08-01 7:03 [PATCH 0/5] Add some DT nodes for Mediatek MT2701 Erin Lo
` (4 preceding siblings ...)
2017-08-01 7:03 ` [PATCH 5/5] arm: dts: mt2701: Add usb3 device nodes Erin Lo
@ 2017-08-01 14:06 ` Matthias Brugger
2017-08-02 4:56 ` Erin Lo
5 siblings, 1 reply; 8+ messages in thread
From: Matthias Brugger @ 2017-08-01 14:06 UTC (permalink / raw)
To: linux-arm-kernel
Hi Erin,
On 08/01/2017 09:03 AM, Erin Lo wrote:
> This patch series based on v4.13-rc1, include MT2701 ethernet/disp bls/display/usb3 function DT nodes.
>
> Chunfeng Yun (1):
> arm: dts: mt2701: Add usb3 device nodes
>
> Sean Wang (1):
> arm: dts: mt2701: Add ethernet device node
>
> Weiqing Kong (2):
> arm: dts: mt2701: Add display bls related nodes for MT2701
> arm: dts: mt2701: Add display bls related nodes for MT2701
>
> YT Shen (1):
> arm: dts: mt2701: Add display subsystem related nodes for MT2701
>
I took 1/5 and 5/5 in v4.13-next/dts32
Please reword the commit message on 2/5 and 3/5.
Also the node should be called pwm instead of bls.
Regards,
Matthias
> arch/arm/boot/dts/mt2701-evb.dts | 27 ++++++
> arch/arm/boot/dts/mt2701.dtsi | 189 +++++++++++++++++++++++++++++++++++++++
> 2 files changed, 216 insertions(+)
>
> --
> 1.9.1
>
^ permalink raw reply [flat|nested] 8+ messages in thread* [PATCH 0/5] Add some DT nodes for Mediatek MT2701
2017-08-01 14:06 ` [PATCH 0/5] Add some DT nodes for Mediatek MT2701 Matthias Brugger
@ 2017-08-02 4:56 ` Erin Lo
0 siblings, 0 replies; 8+ messages in thread
From: Erin Lo @ 2017-08-02 4:56 UTC (permalink / raw)
To: linux-arm-kernel
Hi Matthias,
On Tue, 2017-08-01 at 16:06 +0200, Matthias Brugger wrote:
> Hi Erin,
>
> On 08/01/2017 09:03 AM, Erin Lo wrote:
> > This patch series based on v4.13-rc1, include MT2701 ethernet/disp bls/display/usb3 function DT nodes.
> >
> > Chunfeng Yun (1):
> > arm: dts: mt2701: Add usb3 device nodes
> >
> > Sean Wang (1):
> > arm: dts: mt2701: Add ethernet device node
> >
> > Weiqing Kong (2):
> > arm: dts: mt2701: Add display bls related nodes for MT2701
> > arm: dts: mt2701: Add display bls related nodes for MT2701
> >
> > YT Shen (1):
> > arm: dts: mt2701: Add display subsystem related nodes for MT2701
> >
>
> I took 1/5 and 5/5 in v4.13-next/dts32
>
> Please reword the commit message on 2/5 and 3/5.
> Also the node should be called pwm instead of bls.
>
> Regards,
> Matthias
>
Thanks for your comment.
We will reword pwm instead of bls in next version and send them with 4/5
in recent days.
Regards,
Erin
> > arch/arm/boot/dts/mt2701-evb.dts | 27 ++++++
> > arch/arm/boot/dts/mt2701.dtsi | 189 +++++++++++++++++++++++++++++++++++++++
> > 2 files changed, 216 insertions(+)
> >
> > --
> > 1.9.1
> >
^ permalink raw reply [flat|nested] 8+ messages in thread