[PATCH 0/2] Add support for S805X based P241 Reference Design board

[PATCH 0/2] Add support for S805X based P241 Reference Design board

[Neil Armstrong]

The Amlogic P241 board is the Reference Design board for the S805X
variant of the Amlogic Meson GXL SoC family.

The S805X is a variant of the Amlogic Meson GXL SoC family with the
following physical limitations :
- No SDCard interface
- No GPIOCLK pins
- No USB OTG ID pin (but Gadget feature can stil be forced)
- No 5V regulator
- Reduced ADC inputs (only ADC0 and ADC1)
- GPIODV_26, GPIOAO_3, GPIOAO_4, GPIOAO_5, GPIOAO_6, GPIOX_14,
  GPIOX_15, GPIOH_3 are no more exposed on the package

Amlogic exposes the following SW limitations :
- HDMI max resolution should be 1080p60, VPU clock should be downgraded
- Video Decoding should be limited to 1080p60, VDEC clock should be downgraded
- CPU speed should be limited by SCPI OPP table to 1.2GHz
- DRAM interface is limited to DDR4 16bit up to 1GiB

The P241 board has the following features :
- 1GiB DDR4 Memory
- HDMI Connector with CEC
- A/V jack with Stereo Audio and CVBS
- 10/100 Ethernet
- 2x USB2.0 Type-A
- On-board WiFi SDIO Module
- On-board eMMC storage
- Infraread Received
- Factory Reset button
- UART connector

Neil Armstrong (2):
  dt-bindings: amlogic: Add support for GXL S805X and the P241 board
  ARM64: dts: add S805X based P241 board

 Documentation/devicetree/bindings/arm/amlogic.txt  |   6 +
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s805x-p241.dts      | 218 +++++++++++++++++++++
 3 files changed, 225 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts

-- 
2.7.4

[PATCH 1/2] dt-bindings: amlogic: Add support for GXL S805X and the P241 board

[Neil Armstrong]

The S805X is a variant of the Amlogic Meson GXL SoC family with the
following physical limitations :
- No SDCard interface
- No GPIOCLK pins
- No USB OTG ID pin (but Gadget feature can stil be forced)
- No 5V regulator
- Reduced ADC inputs (only ADC0 and ADC1)
- GPIODV_26, GPIOAO_3, GPIOAO_4, GPIOAO_5, GPIOAO_6, GPIOX_14,
  GPIOX_15, GPIOH_3 are no more exposed on the package

Amlogic exposes the following SW limitations :
- HDMI max resolution should be 1080p60, VPU clock should be downgraded
- Video Decoding should be limited to 1080p60, VDEC clock should be downgraded
- CPU speed should be limited by SCPI OPP table to 1.2GHz
- DRAM interface is limited to DDR4 16bit up to 1GiB

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 Documentation/devicetree/bindings/arm/amlogic.txt | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 6988056..849834c 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -41,6 +41,10 @@ Boards with the Amlogic Meson GXL S905D SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,s905d", "amlogic,meson-gxl";
 
+Boards with the Amlogic Meson GXL S805X SoC shall have the following properties:
+  Required root node property:
+    compatible: "amlogic,s805x", "amlogic,meson-gxl";
+
 Boards with the Amlogic Meson GXM S912 SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,s912", "amlogic,meson-gxm";
@@ -79,6 +83,8 @@ Board compatible values (alphabetically, grouped by SoC):
   - "amlogic,p230" (Meson gxl s905d)
   - "amlogic,p231" (Meson gxl s905d)
 
+  - "amlogic,p241" (Meson gxl s805x)
+
   - "amlogic,q200" (Meson gxm s912)
   - "amlogic,q201" (Meson gxm s912)
   - "khadas,vim2" (Meson gxm s912)
-- 
2.7.4

[PATCH 1/2] dt-bindings: amlogic: Add support for GXL S805X and the P241 board

[Rob Herring]

On Thu, Jul 05, 2018 at 11:50:42AM +0200, Neil Armstrong wrote:
> The S805X is a variant of the Amlogic Meson GXL SoC family with the
> following physical limitations :
> - No SDCard interface
> - No GPIOCLK pins
> - No USB OTG ID pin (but Gadget feature can stil be forced)
> - No 5V regulator
> - Reduced ADC inputs (only ADC0 and ADC1)
> - GPIODV_26, GPIOAO_3, GPIOAO_4, GPIOAO_5, GPIOAO_6, GPIOX_14,
>   GPIOX_15, GPIOH_3 are no more exposed on the package
> 
> Amlogic exposes the following SW limitations :
> - HDMI max resolution should be 1080p60, VPU clock should be downgraded
> - Video Decoding should be limited to 1080p60, VDEC clock should be downgraded
> - CPU speed should be limited by SCPI OPP table to 1.2GHz
> - DRAM interface is limited to DDR4 16bit up to 1GiB
> 
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
> ---
>  Documentation/devicetree/bindings/arm/amlogic.txt | 6 ++++++
>  1 file changed, 6 insertions(+)

Reviewed-by: Rob Herring <robh@kernel.org>

[PATCH 2/2] ARM64: dts: add S805X based P241 board

[Neil Armstrong]

The Amlogic P241 board is the Reference Design board for the S805X
variant of the Amlogic Meson GXL SoC family.

The P241 board has the following features :
- 1GiB DDR4 Memory
- HDMI Connector with CEC
- A/V jack with Stereo Audio and CVBS
- 10/100 Ethernet
- 2x USB2.0 Type-A
- On-board WiFi SDIO Module
- On-board eMMC storage
- Infraread Received
- Factory Reset button
- UART connector

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/meson-gxl-s805x-p241.dts      | 218 +++++++++++++++++++++
 2 files changed, 219 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 34dd0e9..4dcffb0 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -17,6 +17,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-nexbox-a1.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-q200.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts
new file mode 100644
index 0000000..70433e0
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts
@@ -0,0 +1,218 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+#include "meson-gxl-s905x.dtsi"
+
+/ {
+	compatible = "amlogic,p241", "amlogic,s805x", "amlogic,meson-gxl";
+	model = "Amlogic Meson GXL (S805X) P241 Development Board";
+
+	aliases {
+		serial0 = &uart_AO;
+		serial1 = &uart_A;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	memory at 0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x20000000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+};
+
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <100000000>;
+
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};
-- 
2.7.4

[PATCH 0/2] Add support for S805X based P241 Reference Design board

[Jerome Brunet]

On Thu, 2018-07-05 at 11:50 +0200, Neil Armstrong wrote:
> Neil Armstrong (2):
>   dt-bindings: amlogic: Add support for GXL S805X and the P241 board
>   ARM64: dts: add S805X based P241 board
> 
>  Documentation/devicetree/bindings/arm/amlogic.txt  |   6 +
>  arch/arm64/boot/dts/amlogic/Makefile               |   1 +
>  .../boot/dts/amlogic/meson-gxl-s805x-p241.dts      | 218 +++++++++++++++++++++
>  3 files changed, 225 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts

Looks good to me

Acked-by: Jerome Brunet <jbrunet@baylibre.com>

[PATCH 0/2] Add support for S805X based P241 Reference Design board

[Kevin Hilman]

Neil Armstrong <narmstrong@baylibre.com> writes:

> The Amlogic P241 board is the Reference Design board for the S805X
> variant of the Amlogic Meson GXL SoC family.
>
> The S805X is a variant of the Amlogic Meson GXL SoC family with the
> following physical limitations :
> - No SDCard interface
> - No GPIOCLK pins
> - No USB OTG ID pin (but Gadget feature can stil be forced)
> - No 5V regulator
> - Reduced ADC inputs (only ADC0 and ADC1)
> - GPIODV_26, GPIOAO_3, GPIOAO_4, GPIOAO_5, GPIOAO_6, GPIOX_14,
>   GPIOX_15, GPIOH_3 are no more exposed on the package
>
> Amlogic exposes the following SW limitations :
> - HDMI max resolution should be 1080p60, VPU clock should be downgraded
> - Video Decoding should be limited to 1080p60, VDEC clock should be downgraded
> - CPU speed should be limited by SCPI OPP table to 1.2GHz
> - DRAM interface is limited to DDR4 16bit up to 1GiB
>
> The P241 board has the following features :
> - 1GiB DDR4 Memory
> - HDMI Connector with CEC
> - A/V jack with Stereo Audio and CVBS
> - 10/100 Ethernet
> - 2x USB2.0 Type-A
> - On-board WiFi SDIO Module
> - On-board eMMC storage
> - Infraread Received
> - Factory Reset button
> - UART connector

Applied to v4.19/dt64.

The cover letter didn't say, but I assume this was at least boot tested
on a p241 board?

Thanks,

Kevin

[PATCH 0/2] Add support for S805X based P241 Reference Design board

[Neil Armstrong]

On 10/07/2018 00:48, Kevin Hilman wrote:
> Neil Armstrong <narmstrong@baylibre.com> writes:
> 
>> The Amlogic P241 board is the Reference Design board for the S805X
>> variant of the Amlogic Meson GXL SoC family.
>>
>> The S805X is a variant of the Amlogic Meson GXL SoC family with the
>> following physical limitations :
>> - No SDCard interface
>> - No GPIOCLK pins
>> - No USB OTG ID pin (but Gadget feature can stil be forced)
>> - No 5V regulator
>> - Reduced ADC inputs (only ADC0 and ADC1)
>> - GPIODV_26, GPIOAO_3, GPIOAO_4, GPIOAO_5, GPIOAO_6, GPIOX_14,
>>   GPIOX_15, GPIOH_3 are no more exposed on the package
>>
>> Amlogic exposes the following SW limitations :
>> - HDMI max resolution should be 1080p60, VPU clock should be downgraded
>> - Video Decoding should be limited to 1080p60, VDEC clock should be downgraded
>> - CPU speed should be limited by SCPI OPP table to 1.2GHz
>> - DRAM interface is limited to DDR4 16bit up to 1GiB
>>
>> The P241 board has the following features :
>> - 1GiB DDR4 Memory
>> - HDMI Connector with CEC
>> - A/V jack with Stereo Audio and CVBS
>> - 10/100 Ethernet
>> - 2x USB2.0 Type-A
>> - On-board WiFi SDIO Module
>> - On-board eMMC storage
>> - Infraread Received
>> - Factory Reset button
>> - UART connector
> 
> Applied to v4.19/dt64.
> 
> The cover letter didn't say, but I assume this was at least boot tested
> on a p241 board?

Exact, it's boot tested on a p241 board.

Neil


> 
> Thanks,
> 
> Kevin
>