[PATCH 1/2] dt-bindings: arm: rockchip: Add EmbedFire LubanCat 4 board

[PATCH 1/2] dt-bindings: arm: rockchip: Add EmbedFire LubanCat 4 board

[LemonFan-maker]

The LubanCat 4 is a single board computer based on the Rockchip
RK3588S SoC.

Specification:
- Rockchip RK3588S
- 4/8/16GB LPDDR4X
- 32/64/128GB eMMC 5.1
- microSD slot
- HDMI 2.1 Type-A
- Gigabit Ethernet (JLSemi JL21xx PHY)
- Mini PCIe (PCIe 2.0 x1)
- USB-C (with FUSB302 typec controller)
- USB 3.0 Type-A x1
- USB 2.0 Type-A x2
- 3.5mm audio jack (ES8388 codec)
- HYM8563 RTC
- PWM fan header
- 40-pin GPIO header

Signed-off-by: LemonFan-maker <2254650260@qq.com>
---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index aa66a15be233..44b005bc709a 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -191,6 +191,11 @@ properties:
           - const: embedfire,lubancat-2
           - const: rockchip,rk3568
 
+      - description: EmbedFire LubanCat 4
+        items:
+          - const: embedfire,lubancat-4
+          - const: rockchip,rk3588s
+
       - description: Engicam PX30.Core C.TOUCH 2.0
         items:
           - const: engicam,px30-core-ctouch2
-- 
2.55.0

[PATCH 2/2] arm64: dts: rockchip: Add EmbedFire LubanCat 4 board

[LemonFan-maker]

The LubanCat 4 is a single board computer based on the Rockchip
RK3588S SoC.

Add basic device tree support for this board. Currently enabled
peripherals allow the board to boot into a userspace via serial
console, eMMC or SD card, with networking over the on-board
Gigabit Ethernet:

- UART2 debug console
- RK806 SPI PMIC and RK8602/RK8603 CPU/NPU supplies
- eMMC (HS400 enhanced strobe) and SD card (UHS SDR104)
- GMAC1 with RGMII PHY on MDIO1
- HDMI0 output
- PCIe 2.0 x1 (mini PCIe)
- USB 2.0 host ports and USB 3.0 host port
- HYM8563 RTC
- On-board heartbeat LED and PWM fan header

Signed-off-by: LemonFan-maker <2254650260@qq.com>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3588s-lubancat-4.dts  | 782 ++++++++++++++++++
 2 files changed, 783 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-lubancat-4.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 519bb6c431ac..d9fe4cefd67e 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -222,6 +222,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-evb1-v10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-gameforce-ace.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-indiedroid-nova.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-khadas-edge2.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-lubancat-4.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-lubancat-4.dts b/arch/arm64/boot/dts/rockchip/rk3588s-lubancat-4.dts
new file mode 100644
index 000000000000..f8c78df4a14b
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-lubancat-4.dts
@@ -0,0 +1,782 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device tree for EmbedFire LubanCat-4 SBC.
+ *
+ * Copyright (c) 2026 LemonFan-maker <2254650260@qq.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3588s.dtsi"
+
+/ {
+	model = "EmbedFire LubanCat-4";
+	compatible = "embedfire,lubancat-4", "rockchip,rk3588s";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	hdmi0-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi0_con_in: endpoint {
+				remote-endpoint = <&hdmi0_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&sys_status_led_pin>;
+
+		sys-led {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	fan: pwm-fan {
+		compatible = "pwm-fan";
+		cooling-levels = <0 100 150 200 255>;
+		pwms = <&pwm0 0 5000 0>;
+		#cooling-cells = <2>;
+	};
+
+	vcc5v0_dcin: regulator-vcc5v0-dcin {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc5v0_sys: regulator-vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_dcin>;
+	};
+
+	vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v1_nldo_s3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc3v3_pcie20: regulator-vcc3v3-pcie20 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie20";
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb20_host: regulator-vcc5v0-usb20-host {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb20_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb20_host_pwr_en>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb30_host: regulator-vcc5v0-usb30-host {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb30_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb30_host_pwr_en>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&combphy0_ps {
+	status = "okay";
+};
+
+&combphy2_psu {
+	status = "okay";
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&gmac1 {
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	/* The board has 1.5ns delays on RX lines; TX delay is provided by the MAC. */
+	phy-mode = "rgmii-rxid";
+	pinctrl-0 = <&gmac1_miim
+		     &gmac1_tx_bus2
+		     &gmac1_rx_bus2
+		     &gmac1_rgmii_clk
+		     &gmac1_rgmii_bus>;
+	pinctrl-names = "default";
+	tx_delay = <0x1b>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu_s0>;
+	status = "okay";
+};
+
+&hdmi0 {
+	pinctrl-0 = <&hdmim0_tx0_cec
+		     &hdmim0_tx0_hpd
+		     &hdmim0_tx0_scl
+		     &hdmim0_tx0_sda>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&hdmi0_in {
+	hdmi0_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi0>;
+	};
+};
+
+&hdmi0_out {
+	hdmi0_out_con: endpoint {
+		remote-endpoint = <&hdmi0_con_in>;
+	};
+};
+
+&hdptxphy0 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0m2_xfer>;
+	status = "okay";
+
+	vdd_cpu_big0_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big0_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_cpu_big1_s0: regulator@43 {
+		compatible = "rockchip,rk8603", "rockchip,rk8602";
+		reg = <0x43>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big1_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-output-names = "hym8563";
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+		wakeup-source;
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1m2_xfer>;
+	status = "okay";
+
+	vdd_npu_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_npu_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <950000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gmac1_phy_rst>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pcie2x1l2 {
+	pinctrl-0 = <&pcie2_reset>;
+	pinctrl-names = "default";
+	reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie20>;
+	status = "okay";
+};
+
+&pd_gpu {
+	domain-supply = <&vdd_gpu_s0>;
+};
+
+&pinctrl {
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		sys_status_led_pin: sys-status-led-pin {
+			rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	gmac1 {
+		gmac1_phy_rst: gmac1-phy-rst {
+			rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie2_reset: pcie2-reset {
+			rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		usb20_host_pwr_en: usb20-host-pwr-en {
+			rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		usb30_host_pwr_en: usb30-host-pwr-en {
+			rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0m2_pins>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&avcc_1v8_s0>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	no-sdio;
+	no-sd;
+	non-removable;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	max-frequency = <150000000>;
+	no-mmc;
+	no-sdio;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vccio_sd_s0>;
+	status = "okay";
+};
+
+&spi2 {
+	assigned-clocks = <&cru CLK_SPI2>;
+	assigned-clock-rates = <200000000>;
+	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+	status = "okay";
+
+	pmic@0 {
+		compatible = "rockchip,rk806";
+		reg = <0x0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+		spi-max-frequency = <1000000>;
+		system-power-controller;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc5v0_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc5v0_sys>;
+		vcc13-supply = <&vcc_1v1_nldo_s3>;
+		vcc14-supply = <&vcc_1v1_nldo_s3>;
+		vcca-supply = <&vcc5v0_sys>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		regulators {
+			vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
+				regulator-name = "vdd_gpu_s0";
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-enable-ramp-delay = <400>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
+				regulator-name = "vdd_cpu_lit_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_log_s0: dcdc-reg3 {
+				regulator-name = "vdd_log_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <750000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
+				regulator-name = "vdd_vdenc_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_ddr_s0: dcdc-reg5 {
+				regulator-name = "vdd_ddr_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <900000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg6 {
+				regulator-name = "vdd2_ddr_s3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_2v0_pldo_s3: dcdc-reg7 {
+				regulator-name = "vdd_2v0_pldo_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2000000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg8 {
+				regulator-name = "vcc_3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vddq_ddr_s0: dcdc-reg9 {
+				regulator-name = "vddq_ddr_s0";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: dcdc-reg10 {
+				regulator-name = "vcc_1v8_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_1v8_s0: pldo-reg1 {
+				regulator-name = "vcc_1v8_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			avcc_1v8_s0: pldo-reg2 {
+				regulator-name = "avcc_1v8_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			avdd_1v2_s0: pldo-reg3 {
+				regulator-name = "avdd_1v2_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3_s0: pldo-reg4 {
+				regulator-name = "vcc_3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-name = "vccio_sd_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			pldo6_s3: pldo-reg6 {
+				regulator-name = "pldo6_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_0v75_s3: nldo-reg1 {
+				regulator-name = "vdd_0v75_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdd_ddr_pll_s0: nldo-reg2 {
+				regulator-name = "vdd_ddr_pll_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			avdd_0v75_s0: nldo-reg3 {
+				regulator-name = "avdd_0v75_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_0v85_s0: nldo-reg4 {
+				regulator-name = "vdd_0v85_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_0v75_s0: nldo-reg5 {
+				regulator-name = "vdd_0v75_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_otg {
+	status = "okay";
+};
+
+&u2phy2 {
+	status = "okay";
+};
+
+&u2phy2_host {
+	phy-supply = <&vcc5v0_usb30_host>;
+	status = "okay";
+};
+
+&u2phy3 {
+	status = "okay";
+};
+
+&u2phy3_host {
+	phy-supply = <&vcc5v0_usb20_host>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-0 = <&uart2m0_xfer>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host2_xhci {
+	status = "okay";
+};
+
+&usbdp_phy0 {
+	status = "okay";
+};
+
+&vop {
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi0_in_vp0>;
+	};
+};
-- 
2.55.0

Re: [PATCH 1/2] dt-bindings: arm: rockchip: Add EmbedFire LubanCat 4 board

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 75 bytes --]

Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH 1/2] dt-bindings: arm: rockchip: Add EmbedFire LubanCat 4 board

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 256 bytes --]

On Sun, Jul 05, 2026 at 03:37:00PM +0100, Conor Dooley wrote:
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> pw-bot: not-applicable

Actually no, I just noticed you're not using your real name/a known
identity. un-acked until you sort that out.



[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH 2/2] arm64: dts: rockchip: Add EmbedFire LubanCat 4 board

[Andrew Lunn]

> +&gmac1 {
> +	clock_in_out = "output";
> +	phy-handle = <&rgmii_phy1>;
> +	/* The board has 1.5ns delays on RX lines; TX delay is provided by the MAC. */

That is pretty unusual. How is this RX delay done?

> +	phy-mode = "rgmii-rxid";
> +	pinctrl-0 = <&gmac1_miim
> +		     &gmac1_tx_bus2
> +		     &gmac1_rx_bus2
> +		     &gmac1_rgmii_clk
> +		     &gmac1_rgmii_bus>;
> +	pinctrl-names = "default";
> +	tx_delay = <0x1b>;

please take a read of:

https://elixir.bootlin.com/linux/v6.15/source/Documentation/devicetree/bindings/net/ethernet-controller.yaml#L287

Ideally, you want to the PHY adding the delay, not the MAC. 99% of
rockchip boards get this wrong, they have phy-mode 'rgmii', and
{tx|rx}_delay properties. And i tell developers to swap to 'rgmii-id'
and remove the delay properties.

With the PCB adding some delays, you board is slightly
different. Please drop the tx_delay and adjust the phy-mode so the PHY
adds the delay.

	Andrew

Re: [PATCH 2/2] arm64: dts: rockchip: Add EmbedFire LubanCat 4 board

[Pufan Jin]

On Sun, Jul 05, 2026 at 05:11:58PM +0200, Andrew Lunn wrote:
> > +	/* The board has 1.5ns delays on RX lines; TX delay is provided by the MAC. */
>
> That is pretty unusual. How is this RX delay done?

You're right to question this, and I apologise -- the comment was
inaccurate. I re-checked the board schematic and both TXC and RXC
have ~2ns of trace delay added on the PCB (annotated as
"TXC / RXC : delays 2ns" next to the RGMII bus). So neither the MAC
nor the PHY should add any internal delay.

> Ideally, you want to the PHY adding the delay, not the MAC. 99% of
> rockchip boards get this wrong, they have phy-mode 'rgmii', and
> {tx|rx}_delay properties. And i tell developers to swap to 'rgmii-id'
> and remove the delay properties.
>
> With the PCB adding some delays, you board is slightly
> different. Please drop the tx_delay and adjust the phy-mode so the PHY
> adds the delay.

Since the PCB already provides the required clock skew on both
directions, for v2 I will switch to:

    phy-mode = "rgmii";

and drop both the tx_delay property and the misleading comment.

I also need to correct the cover letter: the PHY on the shipping
board revision (20241026) is a Realtek RTL8211F, not a JLSemi JL21xx.
An earlier revision (20240221) used JL21xx, but the current hardware
uses RTL8211F. The cover letter and binding commit message will be
updated accordingly in v2.

I will collect the remaining reviewer feedback before sending v2 and
will re-test the link on hardware with the corrected phy-mode before
posting.

Thanks for the pointer to ethernet-controller.yaml.

Pufan Jin

Re: [PATCH 1/2] dt-bindings: arm: rockchip: Add EmbedFire LubanCat 4 board

[Pufan Jin]

On Sun, Jul 05, 2026 at 03:38:00PM +0100, Conor Dooley wrote:
> On Sun, Jul 05, 2026 at 03:37:00PM +0100, Conor Dooley wrote:
> > Acked-by: Conor Dooley <conor.dooley@microchip.com>
> > pw-bot: not-applicable
>
> Actually no, I just noticed you're not using your real name/a known
> identity. un-acked until you sort that out.

Apologies for the confusion. My real name is Jin Pufan.
In v2 I will change the author identity to:

    From: Pufan Jin <2254650260@qq.com>
    Signed-off-by: Pufan Jin <2254650260@qq.com>

(family name Jin, given name Pufan; using given-name-first Latin
order as is customary on the list.) The Copyright line in the
DTS will be updated to match.

Thanks for the review, and sorry for the noise.

Pufan Jin

Re: [PATCH 2/2] arm64: dts: rockchip: Add EmbedFire LubanCat 4 board

[Andrew Lunn]

On Tue, Jul 07, 2026 at 05:20:35AM +0800, Pufan Jin wrote:
> On Sun, Jul 05, 2026 at 05:11:58PM +0200, Andrew Lunn wrote:
> > > +	/* The board has 1.5ns delays on RX lines; TX delay is provided by the MAC. */
> >
> > That is pretty unusual. How is this RX delay done?
> 
> You're right to question this, and I apologise -- the comment was
> inaccurate. I re-checked the board schematic and both TXC and RXC
> have ~2ns of trace delay added on the PCB (annotated as
> "TXC / RXC : delays 2ns" next to the RGMII bus).

O.K. So both having delays on the PCB is what i would call "somewhat
unusual", vs "pretty unusual" for a single delay.

> Since the PCB already provides the required clock skew on both
> directions, for v2 I will switch to:
> 
>     phy-mode = "rgmii";
> 
> and drop both the tx_delay property and the misleading comment.

Please correct the comment. One issue we have is that many boards use
"rgmii" and are broken. You have a board which uses "rgmii" and it is
in fact correct. It is good to explain why it is correct, otherwise
people could think it is just another broken board.

       Andrew