* [PATCH 1/2] ARM: multi_v7_defconfig: Enable ARM SCMI protocol and drivers
2020-11-09 4:42 [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations Florian Fainelli
@ 2020-11-09 4:42 ` Florian Fainelli
2020-11-09 4:42 ` [PATCH 2/2] arm64: defconfig: " Florian Fainelli
2020-11-09 9:57 ` [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations Sudeep Holla
2 siblings, 0 replies; 6+ messages in thread
From: Florian Fainelli @ 2020-11-09 4:42 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Dong Aisheng, Vinod Koul, Florian Fainelli, Anson Huang,
Geert Uytterhoeven, Li Yang, Catalin Marinas, Michael Walle,
Russell King, Krzysztof Kozlowski, Lad Prabhakar,
Enric Balletbo i Serra, Christian Gmeiner, Joel Stanley,
Sudeep Holla, Olof Johansson, Shawn Guo, Bjorn Andersson,
Will Deacon, open list
Enable the ARM SCMI protocol and the common clock, cpufreq and sensors
drivers. Broadcom STB platforms (ARCH_BRCMSTB) implement SCMI to provide
support for CPU frequency scaling, clock configuration and temperature
and current sensors.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm/configs/multi_v7_defconfig | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index a611b0c1e540..10facef5558c 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -109,6 +109,7 @@ CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
CONFIG_CPUFREQ_DT=y
CONFIG_ARM_IMX6Q_CPUFREQ=y
+CONFIG_ARM_SCMI_CPUFREQ=y
CONFIG_ARM_RASPBERRYPI_CPUFREQ=y
CONFIG_QORIQ_CPUFREQ=y
CONFIG_CPU_IDLE=y
@@ -117,6 +118,7 @@ CONFIG_ARM_ZYNQ_CPUIDLE=y
CONFIG_ARM_EXYNOS_CPUIDLE=y
CONFIG_ARM_TEGRA_CPUIDLE=y
CONFIG_KERNEL_MODE_NEON=y
+CONFIG_ARM_SCMI_PROTOCOL=y
CONFIG_RASPBERRYPI_FIRMWARE=y
CONFIG_TRUSTED_FOUNDATIONS=y
CONFIG_BCM47XX_NVRAM=y
@@ -488,6 +490,7 @@ CONFIG_CHARGER_MAX77693=m
CONFIG_CHARGER_MAX8997=m
CONFIG_CHARGER_MAX8998=m
CONFIG_CHARGER_TPS65090=y
+CONFIG_SENSORS_ARM_SCMI=y
CONFIG_SENSORS_ASPEED=m
CONFIG_SENSORS_IIO_HWMON=y
CONFIG_SENSORS_LM90=y
@@ -959,6 +962,7 @@ CONFIG_CROS_EC_I2C=m
CONFIG_CROS_EC_SPI=m
CONFIG_COMMON_CLK_MAX77686=y
CONFIG_COMMON_CLK_RK808=m
+CONFIG_COMMON_CLK_SCMI=y
CONFIG_COMMON_CLK_S2MPS11=m
CONFIG_CLK_RASPBERRYPI=y
CONFIG_COMMON_CLK_QCOM=y
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] arm64: defconfig: Enable ARM SCMI protocol and drivers
2020-11-09 4:42 [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations Florian Fainelli
2020-11-09 4:42 ` [PATCH 1/2] ARM: multi_v7_defconfig: Enable ARM SCMI protocol and drivers Florian Fainelli
@ 2020-11-09 4:42 ` Florian Fainelli
2020-11-09 9:57 ` [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations Sudeep Holla
2 siblings, 0 replies; 6+ messages in thread
From: Florian Fainelli @ 2020-11-09 4:42 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Dong Aisheng, Vinod Koul, Florian Fainelli, Anson Huang,
Geert Uytterhoeven, Li Yang, Catalin Marinas, Michael Walle,
Russell King, Krzysztof Kozlowski, Lad Prabhakar,
Enric Balletbo i Serra, Christian Gmeiner, Joel Stanley,
Sudeep Holla, Olof Johansson, Shawn Guo, Bjorn Andersson,
Will Deacon, open list
Enable the ARM SCMI protocol and the common clock, cpufreq, reset and
sensors drivers. Broadcom STB platforms (ARCH_BRCMSTB) implement SCMI to
provide support for CPU frequency scaling, clock configuration and
temperature and current sensors.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm64/configs/defconfig | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 5cfe3cf6f2ac..5fcd09e505b4 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -93,8 +93,10 @@ CONFIG_ARM_IMX_CPUFREQ_DT=m
CONFIG_ARM_QCOM_CPUFREQ_NVMEM=y
CONFIG_ARM_QCOM_CPUFREQ_HW=y
CONFIG_ARM_RASPBERRYPI_CPUFREQ=m
+CONFIG_ARM_SCMI_CPUFREQ=y
CONFIG_ARM_TEGRA186_CPUFREQ=y
CONFIG_QORIQ_CPUFREQ=y
+CONFIG_ARM_SCMI_PROTOCOL=y
CONFIG_ARM_SCPI_PROTOCOL=y
CONFIG_RASPBERRYPI_FIRMWARE=y
CONFIG_INTEL_STRATIX10_SERVICE=y
@@ -522,6 +524,7 @@ CONFIG_POWER_RESET_SYSCON=y
CONFIG_SYSCON_REBOOT_MODE=y
CONFIG_BATTERY_SBS=m
CONFIG_BATTERY_BQ27XXX=y
+CONFIG_SENSORS_ARM_SCMI=y
CONFIG_SENSORS_ARM_SCPI=y
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_PWM_FAN=m
@@ -865,6 +868,7 @@ CONFIG_CROS_EC=y
CONFIG_CROS_EC_I2C=y
CONFIG_CROS_EC_SPI=y
CONFIG_CROS_EC_CHARDEV=m
+CONFIG_COMMON_CLK_SCMI=y
CONFIG_COMMON_CLK_RK808=y
CONFIG_COMMON_CLK_SCPI=y
CONFIG_COMMON_CLK_CS2000_CP=y
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations
2020-11-09 4:42 [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations Florian Fainelli
2020-11-09 4:42 ` [PATCH 1/2] ARM: multi_v7_defconfig: Enable ARM SCMI protocol and drivers Florian Fainelli
2020-11-09 4:42 ` [PATCH 2/2] arm64: defconfig: " Florian Fainelli
@ 2020-11-09 9:57 ` Sudeep Holla
2020-11-12 23:08 ` Florian Fainelli
2020-11-28 4:52 ` Florian Fainelli
2 siblings, 2 replies; 6+ messages in thread
From: Sudeep Holla @ 2020-11-09 9:57 UTC (permalink / raw)
To: Florian Fainelli
Cc: Dong Aisheng, Vinod Koul, Michael Walle, Anson Huang,
Geert Uytterhoeven, Will Deacon, Li Yang, Catalin Marinas,
open list, Russell King, Krzysztof Kozlowski, Lad Prabhakar,
Enric Balletbo i Serra, Christian Gmeiner, Joel Stanley,
Sudeep Holla, Olof Johansson, Bjorn Andersson, Shawn Guo,
linux-arm-kernel
On Sun, Nov 08, 2020 at 08:42:26PM -0800, Florian Fainelli wrote:
> This patch series enables support for the ARM SCMI and the various
> drivers provided (cpufreq, clock, sensors, reset) since these are
> utilized by Broadcom STB platforms.
>
> Please let me know if you would like me to carry those patches through
> the ARM SoC pull requests for v5.11 or if you would like to see those
> applied differently.
Both looks fine to me.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
--
Regards,
Sudeep
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations
2020-11-09 9:57 ` [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations Sudeep Holla
@ 2020-11-12 23:08 ` Florian Fainelli
2020-11-28 4:52 ` Florian Fainelli
1 sibling, 0 replies; 6+ messages in thread
From: Florian Fainelli @ 2020-11-12 23:08 UTC (permalink / raw)
To: Sudeep Holla
Cc: Dong Aisheng, Vinod Koul, Michael Walle, Anson Huang,
Geert Uytterhoeven, Will Deacon, Li Yang, Catalin Marinas,
open list, Russell King, Krzysztof Kozlowski, Lad Prabhakar,
Enric Balletbo i Serra, Christian Gmeiner, Joel Stanley,
Olof Johansson, Bjorn Andersson, Shawn Guo, linux-arm-kernel
On 11/9/20 1:57 AM, Sudeep Holla wrote:
> On Sun, Nov 08, 2020 at 08:42:26PM -0800, Florian Fainelli wrote:
>> This patch series enables support for the ARM SCMI and the various
>> drivers provided (cpufreq, clock, sensors, reset) since these are
>> utilized by Broadcom STB platforms.
>>
>> Please let me know if you would like me to carry those patches through
>> the ARM SoC pull requests for v5.11 or if you would like to see those
>> applied differently.
>
> Both looks fine to me.
>
> Acked-by: Sudeep Holla <sudeep.holla@arm.com>
>
Thank you Sudeep, other ARM SoC maintainers, do you mind me picking up
those changes through the Broadcom ARM SoC pull request for 5.11?
--
Florian
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations
2020-11-09 9:57 ` [PATCH 0/2] ARM/ARM64: Enable SCMI in default configurations Sudeep Holla
2020-11-12 23:08 ` Florian Fainelli
@ 2020-11-28 4:52 ` Florian Fainelli
1 sibling, 0 replies; 6+ messages in thread
From: Florian Fainelli @ 2020-11-28 4:52 UTC (permalink / raw)
To: Sudeep Holla
Cc: Dong Aisheng, Vinod Koul, Michael Walle, Anson Huang,
Geert Uytterhoeven, Will Deacon, Li Yang, Catalin Marinas,
open list, Russell King, Krzysztof Kozlowski, Lad Prabhakar,
Enric Balletbo i Serra, Christian Gmeiner, Joel Stanley,
Olof Johansson, Bjorn Andersson, Shawn Guo, linux-arm-kernel
On 11/9/2020 1:57 AM, Sudeep Holla wrote:
> On Sun, Nov 08, 2020 at 08:42:26PM -0800, Florian Fainelli wrote:
>> This patch series enables support for the ARM SCMI and the various
>> drivers provided (cpufreq, clock, sensors, reset) since these are
>> utilized by Broadcom STB platforms.
>>
>> Please let me know if you would like me to carry those patches through
>> the ARM SoC pull requests for v5.11 or if you would like to see those
>> applied differently.
>
> Both looks fine to me.
>
> Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Series applied, thanks!
--
Florian
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread